ADIC-SANMGR-PROXY-MIB

438 objects

No module-level DESCRIPTION found.

Imported Objects

ADIC-INTELLIGENT-STORAGE-MIB	--Type assignments AdicAgentStatus AdicGlobalId Index for Proxy componentId
RFC-1212	OBJECT-TYPE
RFC-1215	TRAP-TYPE
RFC1155-SMI	enterprises experimental Gauge IpAddress TimeTicks
RFC1213-MIB	DisplayString

OID	Name	Access	Status	Description
1.3.6.1.4.1.3764.1.1.400.10	Nodesanmgr-proxy
1.3.6.1.4.1.3764.1.1.400.10.10	Nodepathlight
1.3.6.1.4.1.3764.1.1.400.10.10.2	Nodeagent
1.3.6.1.4.1.3764.1.1.400.10.10.2.1	TableagentScalarTable	not-accessible	mandatory
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1	RowagentScalarEntry	not-accessible	mandatory	A component entry containing objects for a particular component.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.1	ColumnpaIdentify	read-write	mandatory	Flash the READY light on the SAN Data Gateway front panel. A non-zero value turns the LED on for the specified number of seconds. Zero turns LED off.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.2	ColumnpaReboot	read-write	mandatory	Writing a reboot(2) value here causes immediate reboot.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.3	ColumnpaHealthCheckValue	read-only	mandatory	Value in percent of health check tests passed.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.4	ColumnpaHealthCheckLevel	read-write	mandatory	Scrutiny level of health check function.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.5	ColumnpaHealthCheckInterval	read-write	mandatory	Health Check interval in minutes.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.6	ColumnpaEvRptLevel	read-write	mandatory	Used when retrieving Event Log. Events with log level greater than paEvRptLevel are not retrieved.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.7	ColumnpaEventLogLevels	read-write	mandatory	Each of 255 event types has an 8-bit level used when reading log. Currently valid LogLevel range is 0-3.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.8	ColumnpaTrapThresholds	read-write	mandatory	Each of 255 event types has an 8-bit threshold. When the number of events exceeds the Trap Threshold, a trap is generated and sent to all parties listed in the…
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.9	ColumnpaBaudRate	read-write	mandatory	Serial baud rate for SAN Gateway Service Port. Currently, the Agent does not support baud rate change: the rate is hard-coded to 19200 baud.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.11	ColumnpaLogSize	read-write	mandatory	Number of records in entire event log. (Not just current records since boot.)
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.12	ColumnpaCommand	read-write	mandatory	Used for issuing command to SNMP agent.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.13	ColumnpaLogBoot	read-only	mandatory	Absolute index of first log entry at boot.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.14	ColumnpaLogNCurrent	read-write	mandatory	SNMP Get (read) returns number of records since boot subject to viewing level filtering. SNMP Set (write) copies this number of records since boot (subject to …
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.15	ColumnpaLogChronFirst	read-write	obsolete	Used to request range of records from paLogChronFirst to paLogChronLast
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.16	ColumnpaLogChronLast	read-write	obsolete	Used to request range of records from paLogChronFirst to paLogChronLast
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.17	ColumnpaLogScroll	read-write	obsolete	Used to request previous/next range of records event log
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.18	ColumnpaLogFilename	read-write	mandatory	Used to save event log to a file.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.19	ColumnpaEnvironmentState	read-only	mandatory	Temperature and Voltage Status of SAN Data Gateway: ********************************** (LSB) bit 0 Auxiliary Power bit 1 Main Power bit 2 Temperature Warning b…
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.20	ColumnpaGatewayFWRev	read-only	mandatory	SAN Data Gateway Firmware Revision information.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.21	ColumnpaGatewayHWRev	read-only	mandatory	SAN Data Gateway Hardware Revision information.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.22	ColumnpaSnmpFWRev	read-only	mandatory	SNMP Agent Firmware Revision information.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.23	ColumnpaRidTag	read-only	mandatory	SAN Data Gateway RIDTag.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.24	ColumnpaSerialNumber	read-only	mandatory	SAN Data Gateway Serial Number.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.25	ColumnpaServerVersion	read-write	mandatory	Remote Management software writes Server version information here to customize SNMP Agent behavior.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.26	ColumnpaProductType	read-only	mandatory	Type of SAN device
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.27	ColumnpaVPSEnabled	read-only	mandatory	State of VPS Access Control enable.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.28	ColumnpaLicenseKey	read-write	mandatory	Used to pass feature enabling license keys.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.29	ColumnpaThirdPartyCopyEnabled	read-only	mandatory	State of Extended 3rd Party Copy enable. Enabled means that a valid license key has been entered for this feature.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.30	ColumnpaVPSStatus	read-write	mandatory	State of Virtual Private SAN feature. bit 0 : active or inactive. bit 1 : licensed or not licensed. Bit 1 is redundant with MIB var paVPSEnabled. Writing 1 to …
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.31	ColumnpaThirdPartyCopyStatus	read-write	mandatory	State of Extended 3rd Party Copy feature. bit 0 : active or inactive. bit 1 : licensed or not licensed. Bit 1 is redundant with MIB var paThirdPartyCopyEnabled…
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.32	ColumnpaCommandControlLUN	read-write	mandatory	Gateway/Router Command and Control LUN
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.33	ColumnpaSanDirectorEnabled	read-only	mandatory	State of SAN Director Support for this device. To enable, user must write a valid license key to OID paLicenseKey or enter the license key from the service por…
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.34	ColumnpaNodeName	read-only	mandatory	SAN Gateway Node Name.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.35	ColumnpaVPMStatus	read-write	mandatory	State of Virtual Private Map feature. bit 0 : active or inactive. bit 1 : licensed or not licensed.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.36	ColumnpaSRSStatus	read-write	mandatory	State of SAN Replication Services feature. bit 0 : active or inactive. bit 1 : licensed or not licensed.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.37	ColumnpaEthernetType	read-only	mandatory	Current Ethernet Speed.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.38	ColumnpaTrapSequenceNumber	read-only	mandatory	Sequence number of last trap sent by this SNMP Agent.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.39	ColumnpaSysNodeNameMode	read-write	mandatory	Algorithm used when computing Fibre Channel World Wide Node Name for each port. If the value is sameForEachPort(0), then the World Wide Node Name is the same f…
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.40	ColumnpaGhostIOTimeToLive	read-write	mandatory	The amount of time that commands can remain queued in the SNC before being considered stale and discarded. 0 : Never discard (ghost I/O disabled) 1 - 30 : TTL …
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.41	ColumnpaMaxLun	read-only	mandatory	The maximum LUN value possible.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.42	ColumnpaEVPSEnabled	read-write	mandatory	Bit 0: EVPS active if 1, inactive if 0 Bit 1: EVPS licensed if 1, unlicensed if 0
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.43	ColumnpaMaxHostLun	read-only	mandatory	The number of devices one host can see
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.44	ColumnpaAMPStatus	read-write	mandatory	Status of Automatic Multipath feature. bit 0 : active or inactive. bit 1 : licensed or not licensed.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.45	ColumnpaEnableAllScsiTargets	read-write	mandatory	Used to Enable/Disable all-scsi-targets.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.46	ColumnpaHPFStatus	read-write	mandatory	Bit 0: HPF active if 1, inactive if 0 Bit 1: HPF licensed if 1, unlicensed if 0
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.47	ColumnpaSoip2iRescan	read-write	mandatory	Writing true(1) here causes SOIP2 initiator to rescan its bus.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.48	ColumnpaSoipiRescan	read-write	mandatory	Writing true(1) here causes SOIP initiator to rescan its bus.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.49	ColumnpaFLBStatus	read-write	mandatory	Status of Load Balancing feature. bit 0 : active or inactive. bit 1 : licensed or not licensed.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.50	ColumnpaSoip2iScanPeriod	read-write	mandatory	SOIP2 Initiator Scan period in seconds. 0 will disable scan.
1.3.6.1.4.1.3764.1.1.400.10.10.2.1.1.51	ColumnpaCommandFlowLogEnabled	read-only	mandatory	Returns TRUE iff Command Flow Logging is available. Returns FALSE otherwise.
1.3.6.1.4.1.3764.1.1.400.10.10.2.500	TablepaEventLog	not-accessible	mandatory	Entry point for the Agent Event Log Table.
1.3.6.1.4.1.3764.1.1.400.10.10.2.500.1	RowpaEventLogEntry	not-accessible	mandatory
1.3.6.1.4.1.3764.1.1.400.10.10.2.500.1.1	ColumnpaIndex	read-only	mandatory	MIB EventLogEntry Table index.
1.3.6.1.4.1.3764.1.1.400.10.10.2.500.1.2	ColumnpaTime	read-only	mandatory	Time stamp (since boot).
1.3.6.1.4.1.3764.1.1.400.10.10.2.500.1.3	ColumnpaProducer	read-only	mandatory	Numeric identifier for this event's producer.
1.3.6.1.4.1.3764.1.1.400.10.10.2.500.1.4	ColumnpaEventClass	read-only	mandatory	Numeric identifier for this event's class.
1.3.6.1.4.1.3764.1.1.400.10.10.2.500.1.5	ColumnpaEventCode	read-only	mandatory	Numeric code for this event.
1.3.6.1.4.1.3764.1.1.400.10.10.2.500.1.6	ColumnpaSeq	read-only	mandatory	Sequence number (relative record number) since boot.
1.3.6.1.4.1.3764.1.1.400.10.10.2.500.1.7	ColumnpaEventVars	read-only	mandatory	Text description of event.
1.3.6.1.4.1.3764.1.1.400.10.10.3	Nodedevices
1.3.6.1.4.1.3764.1.1.400.10.10.3.1	TablepdDevices	not-accessible	mandatory	Pathlight Physical Device Group *********************************** Each device attached to the Gateway has an entry here.
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1	RowpdDevEntry	not-accessible	mandatory
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.1	ColumnpdIndex	read-only	mandatory	MIB table index
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.2	ColumnpdUID	read-only	mandatory	Universal Identifier
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.3	ColumnpdType	read-only	mandatory	Device Type i.e. disk/tape/cd etc.
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.4	ColumnpdVendor	read-only	mandatory	Device Vendor
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.5	ColumnpdProduct	read-only	mandatory	Device Product Identifier
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.6	ColumnpdBlockSize	read-only	mandatory	Block size in Bytes
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.7	ColumnpdCapacity	read-only	mandatory	Capacity in BLOCKS (see pdBlockSize)
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.8	ColumnpdAccess	read-only	mandatory
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.9	ColumnpdRemovable	read-only	mandatory	Is device removable ?
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.10	ColumnpdStatus	read-only	mandatory	Device Status
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.11	ColumnpdSpeed	read-only	mandatory	Device Speed in MBytes/second
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.12	ColumnpdWidth	read-only	mandatory	Data path width in bits
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.13	ColumnpdSerial	read-only	mandatory	Device Serial Number
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.14	ColumnpdIdentify	read-write	mandatory	Number of seconds to flash identifying LED. Write here to flash LED on device if supported by Gateway and device. Zero turns LED off.
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.15	ColumnpdInterfaceType	read-only	mandatory	This device's type of communication interface.
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.16	ColumnpdBus	read-only	mandatory	SCSI bus number
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.17	ColumnpdId	read-only	mandatory	SCSI Address ID
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.18	ColumnpdLun	read-only	mandatory	SCSI Logical Unit Number.
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.19	ColumnpdCtlrIndex	read-only	mandatory	Index of this device's controller in the Controllers MIB table and type-specific controller tables
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.20	ColumnpdHWRev	read-only	mandatory	Device hardware revision number/identifier
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.21	ColumnpdFWRev	read-only	mandatory	Device firmware revision number/identifier
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.22	ColumnpdReset	read-write	mandatory	Generic device reset if supported. Write reset(1) here to reset device if supported by Gateway firmware and device.
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.23	ColumnpdStatusBits	read-only	mandatory	Device status bits as per SCSI spec.
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.24	ColumnpdScsiAnsiLevel	read-only	mandatory	Device SCSI level.
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.25	ColumnpdTargetLun	read-only	mandatory	This target device's Logical Unit Number as seen from attached host.
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.26	ColumnpdIpAddress	read-only	mandatory	This target device's IP Address if applicable. In case of SAN Gateway or Router, this information is used to allow arbitrary drill-down capability.
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.27	ColumnpdAltVendor	read-only	mandatory	Device alternate Vendor
1.3.6.1.4.1.3764.1.1.400.10.10.3.1.1.28	ColumnpdAltProduct	read-only	mandatory	Device alternate Product Identifier
1.3.6.1.4.1.3764.1.1.400.10.10.4	Nodecontrollers
1.3.6.1.4.1.3764.1.1.400.10.10.4.1	TablepcControllers	not-accessible	mandatory	Pathlight Controller Group ******************************* All controllers installed in the SAN Data Gateway have an entry here AND a parallel entry in the con…
1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1	RowpcCtlrEntry	not-accessible	mandatory
1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.1	ColumnpcIndex	read-only	mandatory	MIB Table index.
1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.2	ColumnpcType	read-only	mandatory	Communication Interface type.
1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.3	ColumnpcVendorId	read-only	mandatory	Integer vendor ID for this controller.
1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.4	ColumnpcProductId	read-only	mandatory	Vendor's integer ID for this controller.
1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.5	ColumnpcRevision	read-only	deprecated	Revision information for this controller. See also pcHWRev and pcFWRev.
1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.6	ColumnpcSubVendor	read-only	mandatory	Integer sub-vendor ID for this controller.
1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.7	ColumnpcSubProduct	read-only	mandatory	Vendor's integer sub-product ID for this controller.
1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.8	ColumnpcMaxBurst	read-write	mandatory	Maximum burst transfer rate in MBytes/second
1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.9	ColumnpcLatency	read-write	mandatory	Latency Timer in Clock Ticks.
1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.10	ColumnpcIdentify	read-write	mandatory	Reserved for flashing identifying LED on device.
1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.11	ColumnpcPCIBus	read-only	mandatory	PCI Bus number in SAN Data Gateway for this controller.
1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.12	ColumnpcPCIDev	read-only	mandatory	PCI device number in SAN Data Gateway for this controller.
1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.13	ColumnpcPCIFunc	read-only	mandatory	PCI Function number in SAN Data Gateway for this contoller.
1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.14	ColumnpcReset	read-write	mandatory	Generic controller reset variable. Not supported for all controller types.
1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.15	ColumnpcRescan	read-write	mandatory	Writing true(1) here causes controller to rescan its bus if rescan is supported for this controller type.
1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.16	ColumnpcLED	read-only	mandatory	Is LED on?
1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.17	ColumnpcHWRev	read-only	mandatory	Hardware revision for this controller.
1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.18	ColumnpcFWRev	read-only	mandatory	Firmware revision for this controller
1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.19	ColumnpcPCISlot	read-only	mandatory	Location of Channel Card on PCI bus
1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.20	ColumnpcPMCSlot	read-only	mandatory	Location of Card: PMC 1, 2 or 3. 0=> Not a PMC card
1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.21	ColumnpcPCIClass	read-only	mandatory	Device class code as per PCI specification.
1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.22	ColumnpcSplitMode	read-write	mandatory	Enable/Disable Split Mode for this controller.
1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.23	ColumnpcChannelMask	read-write	mandatory	Specifies access permissions for this initiator in bits 0 through 18 ************************************************* -* SCSI Channels *- Bit 0 => Is access D…
1.3.6.1.4.1.3764.1.1.400.10.10.4.1.1.24	ColumnpcPortHostType	read-write	mandatory	Host type for this port. Used if VPS is not enabled.
1.3.6.1.4.1.3764.1.1.400.10.10.4.2	TablepcFCCtlrs	not-accessible	mandatory	Entry point for Fibre Channel Controller Device Group ****************************************************** This table parallels the Controller Table: a Fibre…
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1	RowfcCtlrEntry	not-accessible	mandatory
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.1	ColumnfcStatus	read-only	mandatory	Status of the Fibre Channel Controller
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.2	ColumnfcMaxSpeed	read-only	mandatory	Maximum Transfer Speed in MBytes per second.
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.3	ColumnfcWWID	read-only	mandatory	World Wide Identifier for this Fibre Channel Controller.
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.4	ColumnfcFWRev	read-only	mandatory	Firmware revision number/identifier for this Fibre Channel Controller.
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.5	ColumnfcHWRev	read-only	mandatory	Hardware revision number/identifier for this Fibre Channel Controller.
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.6	ColumnfcLoopID	read-write	mandatory	Fibre Channel Loop ID. soft = -1
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.7	ColumnfcFrameSize	read-write	mandatory	Fibre Channel frame size.
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.8	ColumnfcPortType	read-write	mandatory	Fibre Channel Port Type
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.9	ColumnfcMedia	read-only	mandatory	Media type for this Fibre Channel Controller
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.10	ColumnfcSerialNumber	read-only	mandatory	Serial Number for this Fibre Channel Controller.
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.11	ColumnfcLoopIDMode	read-only	mandatory	Fibre Channel Loop ID mode (soft or hard)
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.12	ColumnfcALPhysicalAddress	read-only	mandatory	Arbitrated Loop Physical Address (ALPA)
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.13	ColumnfcPortMode	read-write	mandatory	Fibre Channel Port Mode.
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.14	ColumnfcConnectionOptions	read-write	mandatory	Connection options for ISP2200 FC chip. Values 4 - 8 are reserved.
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.15	ColumnfcCtlrChipType	read-only	mandatory	Type of Fibre Channel controller chip. Valid types are 2100 , 2200 for QLogic ISP2100 and ISP2200 chips.
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.16	ColumnfcTapeFeature	read-only	mandatory	Status of Fibre Channel Tape Specification support. true means this controller supports FC Tape false means this controller does not support FC Tape
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.17	ColumnfcHardID	read-write	mandatory	Fibre Channel Hard ID, the preferred loop ID for this controller. Even if the controller is in Hard Loop ID mode, the actual loop ID is not guaranteed to be fc…
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.18	ColumnfcCurrentSpeedSetting	read-write	mandatory	Speed in Gb/sec. 0: Auto, 1: 1Gb, 2: 2Gb
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.19	ColumnfcCurrentSpeed	read-only	mandatory	Current Speed Indicator Gb/sec.
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.20	ColumnfcFrameBufferSize	read-only	mandatory	Fibre Channel Frame Buffer Size
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.21	ColumnfcLinkFailureCount	read-only	mandatory	Fibre Channel Link Failure Count
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.22	ColumnfcLossSyncCount	read-only	mandatory	Fibre Channel Loss of Sync Count
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.23	ColumnfcLossSignalCount	read-only	mandatory	Fibre Channel Loss of Signal Count
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.24	ColumnfcProtocolErrorCount	read-only	mandatory	Fibre Channel Primitive Sequence Protocol Error Count
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.25	ColumnfcInvalidTxWordCount	read-only	mandatory	Fibre Channel Invalid Transmission Word Count
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.26	ColumnfcInvalidCRCCount	read-only	mandatory	Fibre Channel Invalid CRC Count
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.27	ColumnfcWWNodeName	read-only	mandatory	The World Wide Node Name for this Fibre Channel Controller. The Node Name for this port may computer strictly on the World Wide Node Name for the gateway, or o…
1.3.6.1.4.1.3764.1.1.400.10.10.4.2.1.28	ColumnfcPortID	read-only	mandatory	Fibre Channel Port Identifier 24 bit quantity which uniquely identifies the port within the loop or fabric.
1.3.6.1.4.1.3764.1.1.400.10.10.4.3	TablepcSSACtlrs	not-accessible	obsolete	Entry point for SSA Controller Device Group **************************************************** This table parallels the Controller Table: an SSA controller w…
1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1	RowssaCtlrEntry	not-accessible	obsolete
1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1.1	ColumnssaStatus1	read-only	mandatory	Status on port 1 of dual port SSA card
1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1.2	ColumnssaStatus2	read-only	mandatory	Status on port 2 of dual port SSA card
1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1.3	ColumnssaSpeed	read-write	mandatory	SSA transfer speed 80 Mbytes/second or 160 MBytes/second
1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1.4	ColumnssaUID	read-only	mandatory	Universal Identifier for this SSA Controller.
1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1.5	ColumnssaFWRev	read-only	mandatory	Firmware revision number/identifier for this SSA controller.
1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1.6	ColumnssaMaxTarg	read-write	mandatory	Maximum number of targets supported.
1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1.7	ColumnssaMaxInit	read-write	mandatory	Maximum number of initiators supported.
1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1.8	ColumnssaPathAlg	read-write	mandatory	SSA pathing algorithm.
1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1.9	ColumnssaHWRev	read-only	mandatory	Hardware revision number/identifier for this SSA controller.
1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1.10	ColumnssaMasterPriority	read-only	mandatory	The SSA Master Priority of an SSA node is a number from 0 to 7. SSA initiators elect a master based on this priority. If more than one SSA node has the same pr…
1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1.11	ColumnssaSATAQuota	read-only	mandatory	The SSA SAT Quota A parameter is an 8 bit number that determines 'the maximum number of frames which can be originated from this port before the port is SATisf…
1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1.12	ColumnssaSATBQuota	read-only	mandatory	The SSA SAT Quota B parameter is an 8 bit number that determines 'the maximum number of frames which this port can originate without forwarding a SAT character…
1.3.6.1.4.1.3764.1.1.400.10.10.4.3.1.13	ColumnssaSATIQuota	read-only	mandatory
1.3.6.1.4.1.3764.1.1.400.10.10.4.4	TablepcSCSICtlrs	not-accessible	mandatory	Entry point for SCSI Controller Device Group **************************************************** This table parallels the Controller Table: a SCSI controller …
1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1	RowscsiCtlrEntry	not-accessible	mandatory
1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.1	ColumnscsiStatus	read-only	mandatory	Status for this SCSI controller.
1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.2	ColumnscsiSpeed	read-write	mandatory	SCSI Transaction speed.
1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.3	ColumnscsiRole	read-write	mandatory	Is this a Target or an Initiator ?
1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.4	ColumnscsiHostId	read-write	mandatory	Host ID defaults to 7.
1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.5	ColumnscsiMaxSpeed	read-write	mandatory	Maximum Speed of this SCSI Channel.
1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.6	ColumnscsiTerm	read-write	mandatory	State of internal SCSI bus terminations, if any.
1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.7	ColumnscsiIoCard	read-only	mandatory	Type of SCSI controller hardware.
1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.8	ColumnscsiMaxIds	read-write	mandatory	Maximum Number of IDs for this SCSI controller.
1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.9	ColumnscsiMaxLuns	read-write	mandatory	Maximum Number of LUNs for this SCSI controller.
1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.10	ColumnscsiMaxWidth	read-only	mandatory	Maximum transfer width in bits.
1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.11	ColumnscsiHWRev	read-only	mandatory	Hardware revision for this SCSI controller.
1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.12	ColumnscsiFWRev	read-only	mandatory	Firmware revision for this SCSI controller.
1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.13	ColumnscsiResetOnPowerUp	read-write	mandatory	Enables/Disables SCSI bus reset upon Gateway power-up for this SCSI controller.
1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.14	ColumnscsiMultiInitEnabled	read-write	mandatory	Enables/Disables multi-initiator support on for this SCSI controller.
1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.15	ColumnscsiAlternateHostId	read-write	mandatory	Alternate Host ID for this SCSI controller. -1 means use automatic.
1.3.6.1.4.1.3764.1.1.400.10.10.4.4.1.16	ColumnscsiTargetEnabled	read-only	mandatory	Indicates target ScsiRole support for this SCSI controller.
1.3.6.1.4.1.3764.1.1.400.10.10.5	Nodenotification
1.3.6.1.4.1.3764.1.1.400.10.10.5.1	TablepnTrapDest	not-accessible	obsolete	Trap destination Group Table ****************************************** A list of IP addresses to which SNMP Traps are sent in parallel using UDP Port 162.
1.3.6.1.4.1.3764.1.1.400.10.10.5.1.1	RowpnTrapDestEntry	not-accessible	obsolete
1.3.6.1.4.1.3764.1.1.400.10.10.5.1.1.1	ColumnpnIndex	read-write	obsolete	Index into TrapDest table
1.3.6.1.4.1.3764.1.1.400.10.10.5.1.1.2	ColumnpnIPAddr	read-write	obsolete	IP Address of destination entity to which traps are sent.
1.3.6.1.4.1.3764.1.1.400.10.10.5.1.1.3	ColumnpnUdpPort	read-write	obsolete	UDP Port on which traps are sent to this entity.
1.3.6.1.4.1.3764.1.1.400.10.10.5.1.1.4	ColumnpnTrapStyle	read-write	obsolete	Style to be used when building a trap PDU to be sent to this entity. A value of proprietary(1) selects the proprietary format used by the Pathlight SAN Directo…
1.3.6.1.4.1.3764.1.1.400.10.10.5.1.1.5	ColumnpnTrapBroadcastMode	read-write	mandatory	Used to Enable/Disable the broadcasting of traps.
1.3.6.1.4.1.3764.1.1.400.10.10.6	NodepanelLED
1.3.6.1.4.1.3764.1.1.400.10.10.7	NodepaHost
1.3.6.1.4.1.3764.1.1.400.10.10.7.1	TablehostCommandTable	not-accessible	mandatory
1.3.6.1.4.1.3764.1.1.400.10.10.7.1.1	RowhostCommandEntry	not-accessible	mandatory	An object for issuing host-related commands to the SNC.
1.3.6.1.4.1.3764.1.1.400.10.10.7.1.1.1	ColumnhostCommand	read-write	mandatory	Used to issue commands to VPS control software. Possible commands are: commitChanges: commits any pending LUN Mapping changes to persistent memory.
1.3.6.1.4.1.3764.1.1.400.10.10.7.2	TablehostInitiator	not-accessible	mandatory	Attached Host Group Table *************************** List of attached hosts and pertinent information.
1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1	RowhostInitiatorEntry	not-accessible	mandatory
1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1.1	ColumnhostIndex	read-write	mandatory	Index into Host Initiator table
1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1.2	ColumnhostRowStatus	read-write	mandatory	Row Status for this row.
1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1.3	ColumnhostWWName	read-write	mandatory	World Wide name of this Initiator.
1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1.4	ColumnhostName	read-write	mandatory	Name for this Initiator.
1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1.5	ColumnhostType	read-write	mandatory	Operating System and other host environment information.
1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1.6	ColumnhostPortID	read-write	mandatory
1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1.7	ColumnhostSANConnection	read-only	mandatory	SAN Connection (1-6) to which this host is connected.
1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1.8	ColumnhostConnectionType	read-only	mandatory	Type of data connection (FCAL , etc.)
1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1.9	ColumnhostITLData	read-write	mandatory	ITL Access Control data for this host. 256 possible LUNs with one Byte of data per LUN.
1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1.10	ColumnhostIPAddr	read-only	mandatory	IP Address of this host. Host is not required to have an IP address.
1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1.11	ColumnhostLunType	read-write	mandatory	The type of this host for EVPS. 8-bit, 16-bit, or volume set
1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1.12	ColumnhostLunMap	read-write	mandatory	EVPS Map data. 256 possible LUNs with two Bytes of data for each lun
1.3.6.1.4.1.3764.1.1.400.10.10.7.2.1.13	ColumnhostInbandAccess	read-write	mandatory	The in-band access level of the host
1.3.6.1.4.1.3764.1.1.400.10.10.8	NodescsiMap
1.3.6.1.4.1.3764.1.1.400.10.10.8.1	TablescsiMapCommandTable	not-accessible	mandatory
1.3.6.1.4.1.3764.1.1.400.10.10.8.1.1	RowscsiMapCommandEntry	not-accessible	mandatory	An object for issuing VPM-related commands to the SNC.
1.3.6.1.4.1.3764.1.1.400.10.10.8.1.1.1	ColumnscsiMapCommand	read-write	mandatory	Used to issue commands to SCSI Channel map (VPM) routines.
1.3.6.1.4.1.3764.1.1.400.10.10.8.2	TablescsiChannelMap	not-accessible	mandatory	SCSI Channel Device Map Table ****************************** List of devices presented to SCSI attached initiator. The initiator sees a series of (Target ID , …
1.3.6.1.4.1.3764.1.1.400.10.10.8.2.1	RowscsiMapEntry	not-accessible	mandatory
1.3.6.1.4.1.3764.1.1.400.10.10.8.2.1.1	ColumnscsiMapRowStatus	read-write	mandatory	Specifies the state of the row.
1.3.6.1.4.1.3764.1.1.400.10.10.8.2.1.2	ColumnscsiMapPort	read-only	mandatory	SCSI port (bus) number for this entry (1 thru 10).
1.3.6.1.4.1.3764.1.1.400.10.10.8.2.1.3	ColumnscsiMapTid	read-only	mandatory	SCSI Target ID for this entry.
1.3.6.1.4.1.3764.1.1.400.10.10.8.2.1.4	ColumnscsiMapLun	read-only	mandatory	SCSI LUN for this entry.
1.3.6.1.4.1.3764.1.1.400.10.10.8.2.1.5	ColumnscsiMapAssignedLun	read-write	mandatory	Pathlight LUN assigned to this entry. This assigned LUN maps to some device connected to the Gateway/Router by some other means (FC, SSA, SCSI, ...).
1.3.6.1.4.1.3764.1.1.400.10.10.8.2.1.6	ColumnscsiMapComments	read-write	mandatory	User's comments for this entry.
1.3.6.1.4.1.3764.1.1.400.10.10.8.2.1.7	ColumnscsiMapPdIndex	read-only	mandatory	Index into Pathlight SANMgr MIB Device Table ( pd group ). The Device Table has more detailed information about attached devices.
1.3.6.1.4.1.3764.1.1.400.10.10.9	NodedeviceMap
1.3.6.1.4.1.3764.1.1.400.10.10.9.1	TabledeviceMapCommandTable	not-accessible	mandatory
1.3.6.1.4.1.3764.1.1.400.10.10.9.1.1	RowdeviceMapCommandEntry	not-accessible	mandatory	An object for issuing VPM-related commands to the SNC.
1.3.6.1.4.1.3764.1.1.400.10.10.9.1.1.1	ColumndeviceMapCommand	read-write	mandatory	Used to issue commands to device map map routines.
1.3.6.1.4.1.3764.1.1.400.10.10.9.1.1.2	ColumndeviceMapMultipathMode	read-write	mandatory	Used to set the Multipath mode.
1.3.6.1.4.1.3764.1.1.400.10.10.9.1.1.3	ColumndeviceMapRemoveDevice	write-only	mandatory	Used to remove a device from the Device Map given its Device-Id. Warning: This command stops the IO for this device before removing
1.3.6.1.4.1.3764.1.1.400.10.10.9.1.1.4	ColumndeviceLoadBalancingMode	read-write	mandatory	Used to set the Load Balancing Mode.
1.3.6.1.4.1.3764.1.1.400.10.10.9.2	TabledmDeviceMap	not-accessible	mandatory	Device Map Group *********************************** Each device attached to the Gateway has an entry here. Historical data of devices not presently connected …
1.3.6.1.4.1.3764.1.1.400.10.10.9.2.1	RowdmDevMapEntry	not-accessible	mandatory
1.3.6.1.4.1.3764.1.1.400.10.10.9.2.1.1	ColumndmRowStatus	read-write	mandatory	Row Control Object for this row
1.3.6.1.4.1.3764.1.1.400.10.10.9.2.1.2	ColumndmAssignedLun	read-only	mandatory	Logical Unit Number assigned to this attached device. Range is 0 thru 255.
1.3.6.1.4.1.3764.1.1.400.10.10.9.2.1.3	ColumndmType	read-write	mandatory	Type of device (FC, SCSI, SNA, SSA).
1.3.6.1.4.1.3764.1.1.400.10.10.9.2.1.4	ColumndmPort	read-write	mandatory	SAN Gateway Port to which this device is connected. May be 1 thru 10 for SCSI, 1 thru 6 for Fibre Channel, 1 thru 3 for SSA.
1.3.6.1.4.1.3764.1.1.400.10.10.9.2.1.5	ColumndmTargetId	read-write	mandatory	The Target ID of the attached target device. This is the actual target ID of the device, not fabricated by the Gateway or Router.
1.3.6.1.4.1.3764.1.1.400.10.10.9.2.1.6	ColumndmTargetLun	read-write	mandatory	The Logical Unit Number of the attached target device. This is the actual LUN of the device, not fabricated by the Gateway or Router.
1.3.6.1.4.1.3764.1.1.400.10.10.9.2.1.7	ColumndmUid	read-write	mandatory	A universally unique identifier for this target device.
1.3.6.1.4.1.3764.1.1.400.10.10.9.2.1.8	ColumndmPath	read-only	mandatory	The Multipath Mode of the device. The mode can only be single(0), manual(1), or auto(1).
1.3.6.1.4.1.3764.1.1.400.10.10.9.2.1.9	ColumndmSerialNum	read-only	mandatory	The Serial Number of the device.
1.3.6.1.4.1.3764.1.1.400.10.10.10	Nodereplication
1.3.6.1.4.1.3764.1.1.400.10.10.10.1	TablesrsDevTable	not-accessible	mandatory	Entry point for SAN Replication Service Device Group ***************************************************** Each SAN Replication Service Device has an entry in …
1.3.6.1.4.1.3764.1.1.400.10.10.10.1.1	RowsrsDevEntry	not-accessible	mandatory
1.3.6.1.4.1.3764.1.1.400.10.10.10.1.1.1	ColumnsrsDevId	read-only	mandatory	Device ID for this SRS Device.
1.3.6.1.4.1.3764.1.1.400.10.10.10.1.1.2	ColumnsrsDevState	read-only	mandatory	State of this LUN Replicated Device.
1.3.6.1.4.1.3764.1.1.400.10.10.10.1.1.3	ColumnsrsDevCommand	read-write	mandatory	Used to invoke SAN Replication Services API commands. Parameters may be passed in the same SNMP Set varbind list with the srsDevCommand as the last varbind. **…
1.3.6.1.4.1.3764.1.1.400.10.10.10.1.1.4	ColumnsrsDevAssignedLun	read-write	mandatory	Assigned LUN of the SAN Replication Service Device's Primary.
1.3.6.1.4.1.3764.1.1.400.10.10.10.1.1.5	ColumnsrsDevMemberCount	read-only	mandatory	Number of members of this LUN Replicated Device.
1.3.6.1.4.1.3764.1.1.400.10.10.10.1.1.6	ColumnsrsDevMembersOnline	read-only	mandatory	Number of members online.
1.3.6.1.4.1.3764.1.1.400.10.10.10.1.1.7	ColumnsrsDevFlags	read-write	mandatory	SCSI device flags for this SAN Replication Service Device.
1.3.6.1.4.1.3764.1.1.400.10.10.10.1.1.8	ColumnsrsDevSizeInBlocks	read-write	mandatory	Size in blocks of this SAN Replication Services Device.
1.3.6.1.4.1.3764.1.1.400.10.10.10.1.1.9	ColumnsrsDevBlockSize	read-write	mandatory	Block size in octets.
1.3.6.1.4.1.3764.1.1.400.10.10.10.1.1.10	ColumnsrsDevPrimary	read-write	mandatory	The Assigned LUN of this SRS Device's Primary.
1.3.6.1.4.1.3764.1.1.400.10.10.10.2	TablesrsMemTable	not-accessible	mandatory	Entry point for SAN Replication Services Member Group ***************************************************** This table lists the Members of each SRS Device.
1.3.6.1.4.1.3764.1.1.400.10.10.10.2.1	RowsrsMemEntry	not-accessible	mandatory
1.3.6.1.4.1.3764.1.1.400.10.10.10.2.1.1	ColumnsrsMemDeviceId	read-only	mandatory	Device ID of the SAN Replication Services Device to which this member belongs.
1.3.6.1.4.1.3764.1.1.400.10.10.10.2.1.2	ColumnsrsMemId	read-only	mandatory	Member ID (index) of this member device.
1.3.6.1.4.1.3764.1.1.400.10.10.10.2.1.3	ColumnsrsMemState	read-only	mandatory	State of this SAN Replication Services Device Member.
1.3.6.1.4.1.3764.1.1.400.10.10.10.2.1.4	ColumnsrsMemCommand	read-write	mandatory	Used to invoke SAN Replication Services API methods. Parameters may be passed in the same SNMP Set varbind list with the lrmCommand as the last varbind.
1.3.6.1.4.1.3764.1.1.400.10.10.10.2.1.5	ColumnsrsMemType	read-only	mandatory	Is this device a primary or secondary member.
1.3.6.1.4.1.3764.1.1.400.10.10.10.2.1.6	ColumnsrsMemSyncPoint	read-only	mandatory	Number of blocks synchronized so far. Used for monitoring synchronization.
1.3.6.1.4.1.3764.1.1.400.10.10.10.2.1.7	ColumnsrsMemAssignedLun	read-write	mandatory	Assigned LUN for this SRS Member.
1.3.6.1.4.1.3764.1.1.400.10.10.10.2.1.8	ColumnsrsMemReadOptions	read-write	mandatory	SRS Member read options.
1.3.6.1.4.1.3764.1.1.400.10.10.10.2.1.9	ColumnsrsMemWriteOptions	read-write	mandatory	SRS Member write options.
1.3.6.1.4.1.3764.1.1.400.10.10.11	NodeenvData
1.3.6.1.4.1.3764.1.1.400.10.10.11.1	TableenvDataTable	not-accessible	mandatory	Entry point for Environmental Data Group ***************************************************** This table lists the attributes of each environmental data.
1.3.6.1.4.1.3764.1.1.400.10.10.11.1.1	RowenvDataEntry	not-accessible	mandatory
1.3.6.1.4.1.3764.1.1.400.10.10.11.1.1.1	ColumnenvDataId	read-only	mandatory
1.3.6.1.4.1.3764.1.1.400.10.10.11.1.1.2	ColumnenvDataName	read-only	mandatory	Name of this environmental data
1.3.6.1.4.1.3764.1.1.400.10.10.11.1.1.3	ColumnenvNominalLo	read-only	mandatory	Minimum value for Nominal status Warning state occurs if the current value is less than this
1.3.6.1.4.1.3764.1.1.400.10.10.11.1.1.4	ColumnenvNominalHi	read-only	mandatory	Maximum Value for Nominal status Warning state occurs if the current value is greater than this.
1.3.6.1.4.1.3764.1.1.400.10.10.11.1.1.5	ColumnenvWarningLo	read-only	mandatory	Minimum value for Warning status Alarm state occurs if the current value is less than this
1.3.6.1.4.1.3764.1.1.400.10.10.11.1.1.6	ColumnenvWarningHi	read-only	mandatory	Maximum Value for Warning status Alarm state occurs if the current value is greater than this.
1.3.6.1.4.1.3764.1.1.400.10.10.11.1.1.7	ColumnenvCurValue	read-only	mandatory	Current Value.
1.3.6.1.4.1.3764.1.1.400.10.10.11.1.1.8	ColumnenvCurStatus	read-only	mandatory	Current Status: Nominal, Warning, or Alarm.
1.3.6.1.4.1.3764.1.1.400.10.10.11.1.1.9	ColumnenvUnit	read-only	mandatory	Unit
1.3.6.1.4.1.3764.1.1.400.10.10.12	NodeportFailover
1.3.6.1.4.1.3764.1.1.400.10.10.12.1	NodefcHostPortFailover
1.3.6.1.4.1.3764.1.1.400.10.10.12.1.1	TablefcHPFPortMappings	not-accessible	mandatory	FC Host Port Failover Mapping *********************************** This table consists of port mappings for the FC Host Port Failover
1.3.6.1.4.1.3764.1.1.400.10.10.12.1.1.1	RowfcHPFMapEntry	not-accessible	mandatory	SNMP table for FC Host Port Failover Mappings
1.3.6.1.4.1.3764.1.1.400.10.10.12.1.1.1.1	ColumnfcHPFMapRowStatus	read-write	mandatory	Row Control Object for this row
1.3.6.1.4.1.3764.1.1.400.10.10.12.1.1.1.2	ColumnfcHPFMapVirtualPort	read-write	mandatory	The virtual port index. Depends on the configuration. Usaually same as phys port index, but 0 if not configured
1.3.6.1.4.1.3764.1.1.400.10.10.12.1.1.1.3	ColumnfcHPFMapPrimaryPort	read-write	mandatory	The physical port index that acts as the default standby
1.3.6.1.4.1.3764.1.1.400.10.10.12.1.1.1.4	ColumnfcHPFMapStandbyList	read-write	mandatory	The comma seperated list of ports that are configured as standbys for the virtual port, excluding the primary port.
1.3.6.1.4.1.3764.1.1.400.10.10.12.1.1.1.5	ColumnfcHPFMapActivePort	read-write	mandatory	The physical port thats active on this virtual port
1.3.6.1.4.1.3764.1.1.400.10.10.12.1.2	TablefcHPFPhysicalPorts	not-accessible	mandatory	FC Host Port Failover Physical Ports *************************************** This table consists of physical port settings for the FC Host Port Failover
1.3.6.1.4.1.3764.1.1.400.10.10.12.1.2.1	RowfcHPFPhysicalPortEntry	not-accessible	mandatory	SNMP table for FC Host Port Failover Port Settings
1.3.6.1.4.1.3764.1.1.400.10.10.12.1.2.1.1	ColumnfcHPFPhysicalPortRowStatus	read-write	mandatory	Row Control Object for this row
1.3.6.1.4.1.3764.1.1.400.10.10.12.1.2.1.2	ColumnfcHPFPhysicalPort	read-only	mandatory	The physical FC port Index. The range depends on the pathlight model.
1.3.6.1.4.1.3764.1.1.400.10.10.12.1.2.1.3	ColumnfcHPFPhysicalPortFailureType	read-only	mandatory	If this phys port failed, this field gives the type of failure.Values 0 = None, 1 = Link Down 2 = Link Error
1.3.6.1.4.1.3764.1.1.400.10.10.12.1.2.1.4	ColumnfcHPFPhysicalPortCurrentState	read-only	mandatory	The current state of this physical port. The values 0 = Online, 1 = Offline
1.3.6.1.4.1.3764.1.1.400.10.10.12.1.2.1.5	ColumnfcHPFPhysicalPortIntervention	read-write	mandatory	Does this physical port require intervention? Values 1 = true, 2 = false
1.3.6.1.4.1.3764.1.1.400.10.10.12.1.3	TablefcHPFGlobalTable	not-accessible	mandatory	FC Host Port Failover Global Settings **************************************** This table consists of settings global to the HPF function.
1.3.6.1.4.1.3764.1.1.400.10.10.12.1.3.1	RowfcHPFGlobalEntry	not-accessible	mandatory	SNMP table for FC Host Port Failover Global Settings
1.3.6.1.4.1.3764.1.1.400.10.10.12.1.3.1.1	ColumnfcHPFLinkDownThreshold	read-write	mandatory	Used to set the Link Down threshold in seconds. Only after this delay the failover triggers
1.3.6.1.4.1.3764.1.1.400.10.10.12.1.3.1.2	ColumnfcHPFErrorRecoveryMode	read-write	mandatory	Used to set the global recovery mode for failures that happen due to FC cable errors Values: returnToActive(0), returnToStandby(1), requiresIntervention(2)
1.3.6.1.4.1.3764.1.1.400.10.10.12.1.3.1.3	ColumnfcHPFLinkDownRecoveryMode	read-write	mandatory	Used to set the global recovery mode for failures that happen due to Link Down Errors Values: returnToActive(0), returnToStandby(1), requiresIntervention(2)
1.3.6.1.4.1.3764.1.1.400.10.10.13	NodeutilityModule
1.3.6.1.4.1.3764.1.1.400.10.10.13.1	TableutilityModuleTable	not-accessible	mandatory	Entry point for Utility Module Group *****************************************************
1.3.6.1.4.1.3764.1.1.400.10.10.13.1.1	RowutilityModuleEntry	not-accessible	mandatory
1.3.6.1.4.1.3764.1.1.400.10.10.13.1.1.1	ColumnutilityModuleId	read-only	mandatory	Utility module index.
1.3.6.1.4.1.3764.1.1.400.10.10.13.1.1.2	ColumnutilityModuleVersion	read-only	mandatory	Utility module version identifier.
1.3.6.1.4.1.3764.1.1.400.10.10.1000	NodetrapDefinition
1.3.6.1.4.1.3764.1.1.400.10.10.1000.1	NodessaPortUpEvent			An SSA Port Up Event has occurred.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.2	NodessaPortDownEvent			An SSA Port Down Event has occurred.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.3	NodessaUidAddedEvent			An SSA UID Added Event has occurred.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.4	NodessaUidRemovedEvent			An SSA UID Removed Event has occurred.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.5	NodessaWebReconfiguredEvent			An SSA Web Reconfigured Event has occurred.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.6	NodessaAsyncErrorEvent			An SSA Async Error Event has occurred.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.7	NodessaAdapterEvent			An SSA Adapter Event has occurred.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.8	NodesenseDataEvent			Sense Data recorded following a check condition. Normally, the host system will request and process sense data, and then perform error recovery.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.9	NodeunitAttentionEvent			A LUN reports a unit attention condition on a non-removable media device.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.10	NodeibfEvent			An Internal Bus Fault event has occurred.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.11	NodetemperatureChangeEvent			A temperature sensor has reported a change from one of three possible states to a another. The possible states are OK, High, Very High. The display string cont…
1.3.6.1.4.1.3764.1.1.400.10.10.1000.12	NodetimeReferenceEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.13	NodeshutdownEvent			This unit is shutting down as a result of a restart request.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.14	NodediagnosticEvent			This event is used for diagnostic purposes.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.15	NodeconfigurationEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.16	NodeunexpectedScsiInterruptEvent			A SCSI bus reports an unexpected interrupt.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.17	NodelipResetEvent			A Fibre Channel interface reports a LIP reset was received from a host.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.18	NodefcSystemErrorEvent			A Fibre Channel interace reports a system error.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.19	NodefcRequestTransferErrorEvent			A Fibre Channel interface reports an error processing a request.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.20	NodefcResponseTransferErrorEvent			A Fibre Channel interface reports an error processing a response.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.21	NodememoryFaultEvent			Processor memory fault detected.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.22	NodefcLipEvent			A Fibre Channel interface detected a LIP.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.23	NodefcLoopUpEvent			A Fibre Channel interface reports loop up.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.24	NodefcLoopDownEvent			A Fibre Channel interface reports loop down.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.25	NodepciBusParityErrorEvent			Parity error detected on unit internal PCI bus.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.26	NodepciInterfaceErrorEvent			Interface error detected on unit internal PCI bus.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.27	NodescsiDeviceAddedEvent			A device has been added to a SCSI bus.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.28	NodescsiBusResetEvent			A SCSI interface reports a bus reset was detected.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.29	NodedeviceAddedEvent			This unit has added a device to its configuration table. Note: This trap is held off until the unit has been up for 60 seconds.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.30	NodedeviceRemovedEvent			This unit has removed a device from its configuration table.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.31	NodeloggingStartedEvent			Event logging service has started.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.32	NodeloggingStoppedEvent			Event logging service has stopped.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.33	NodeinterfaceBusFaultEvent			An interface has detected a bus fault. The display string contained in varbind paEventVars contains the details of which interface detected the fault.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.34	NodeinterfaceDeviceFaultEvent			An interface has detected a device fault. The display string contained in varbind paEventVars contains the details of which interface detected the fault.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.35	NodescsiUnexpectedDisconnectEvent			A SCSI interface has reported an unexpected disconnect by a device.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.36	NodescsiParityErrorEvent			A SCSI interface has detected a parity error on the bus.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.37	NodefcPortDatabaseChangeEvent			Fibre Channel port databse change detected.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.38	NodeddfMemoryErrorEvent			An error was detected on the Direct Data Flow memory board.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.39	NodefcDirectoryServerChangeEvent			The Directory Server on the Fibre Channel fabric has changed.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.40	NodelunLimitExcededEvent			The maximum LUN limit has been exceded, too many devices connected.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.41	NodefcTransferFailureEvent			Fibre Channel transfer error.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.42	NodedeviceLimitExcededEvent			The maximum device limit has been exceded, the persistent device map database is full.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.43	NodefcDebugDumpEvent			A Fibre Channel interface driver has reported a a debug dump.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.44	NodeexcessiveScsiBusErrorsEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.45	NodememoryScrubberErrorEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.46	NodesrsDeviceCreatedEvent			A new SAN Replication Services device has been created
1.3.6.1.4.1.3764.1.1.400.10.10.1000.47	NodesrsDeviceOnlineEvent			A SAN Replication Services device has entered the online state.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.48	NodesrsDeviceRemovedEvent			A SAN Replication Services device has been removed (deleted).
1.3.6.1.4.1.3764.1.1.400.10.10.1000.49	NodesrsDeviceFailedEvent			A SAN Replication Services device has failed.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.50	NodesrsMemberAddedEvent			A new member LUN has been added to a SAN Replication Services device.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.51	NodesrsMemberSuspendedEvent			A SAN Replication Services member has been suspended.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.52	NodesrsMemberRemovedEvent			A SAN Replication Services member has been removed.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.53	NodesrsMemberSyncStartedEvent			A SAN Replication Service member has begun synchronization to the primary member.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.54	NodesrsMemberSyncDoneEvent			A SAN Replication Service member has completed synchronization to the primary member.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.55	NodesrsMemberSyncErrorEvent			An error was detect during synchronization of a SAN Replication Service member to the primary member.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.56	NodesrsMemberRetryEvent			A command issued to a SAN Replication Services member has failed and is being retried.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.57	NodesrsMemberErrorEvent			A command issued to a SAN Replication Services member has resulted in an error.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.58	NodeenvPowerNominalEvent			Power has returned to nominal state from a warning or alarm state.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.59	NodeenvPowerWarningEvent			Power has entered a warning state from a nominal state (power degrading) or alarm state (power improving).
1.3.6.1.4.1.3764.1.1.400.10.10.1000.60	NodeenvPowerAlarmEvent			Power has entered an alarm state.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.61	NodeenvTemperatureNominalEvent			Inlet air, outlet air, or I/O processor temperature has returned to nominal state from a warning or alarm state.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.62	NodeenvInletTemperatureWarningEvent			Inlet air temperature has entered a warning state from a nominal state (temperature increasing) or an alarm state (temperature decreasing).
1.3.6.1.4.1.3764.1.1.400.10.10.1000.63	NodeenvInletTemperatureAlarmEvent			Inlet air temperature has entered an alarm state.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.64	NodeenvOutletTemperatureWarningEvent			Outlet air temperature has entered a warning state from a nominal state (temperature increasing) or an alarm state (temperature decreasing).
1.3.6.1.4.1.3764.1.1.400.10.10.1000.65	NodeenvOutletTemperatureAlarmEvent			Outlet air temperature has entered an alarm state.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.66	NodeenvFanNominalEvent			Fan has entered a nominal state from a fault state.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.67	NodeenvFanWarningEvent			Fan has entered a warning range (tachometer fans only).
1.3.6.1.4.1.3764.1.1.400.10.10.1000.68	NodeenvFanAlarmEvent			Fan has entered an alarm range (tachometer fans) or is stalled (rotor stall fans).
1.3.6.1.4.1.3764.1.1.400.10.10.1000.69	NodeeccMemoryErrorEvent			Error correcting code memory has detected an error.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.70	NoderestartCompleteEvent			Restart process has completed.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.71	NodefirmwareUploadCompleteEvent			Firmware upload process has completed.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.72	NodemaxInitiatorsExceededEvent			Maximum number of initiators has been exceeded.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.73	NodedataPathFailoverEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.74	NodeamemWarningEvent			Amem memory not properly installed.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.75	NodehostOfflineEvent			An attached host has been moved to the offline state.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.76	NodehostOnlineEvent			An attached host has been moved to the online state.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.77	NodehostPortFailoverEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.78	NodehpfRequiresInterventionEvent			Host port failover requires invention.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.79	NodecontrollerResetCompletedEvent			The controller indicated in paEventVars has completed its reset sequence. The text format for paEventVars is: NOTICE: FC Controller %d Restart Complete
1.3.6.1.4.1.3764.1.1.400.10.10.1000.80	NodecontrollerStatusChangeEvent			The status of the controller indicated in paEventVars has changed. The controller index (pcIndex) and the new status (fcStatus for Fibre Channel, scsiStatus fo…
1.3.6.1.4.1.3764.1.1.400.10.10.1000.81	NodeethFailoverEvent			Ethernet Port Filover has occured.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.82	NodememUsageWarningEvent			Memory usage reached warning level.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.83	NodetaskSuspendedWarningEvent			Task suspended warning.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.84	NodeumTaskWatchdogWarningEvent			Utility module task watchdog warning.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.85	NodedataPathTrespassEvent			Data path trespass has occurred.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.86	NodedeviceListChangedEvent			Target device list changed on an interface.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.87	NodeautoLevelStart			Auto Level has begun.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.88	NodeautoLevelEnd			Auto Level is done.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.89	NodeautoLevelError			Auto Level has got error.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.90	NodecorruptNVRAMError			NVRAM corruption detected.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.100	NodepowerSupplyOutOfSpecEvent			The main power supply voltage is out of specified operating range.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.101	NodeauxPowerOutOfSpecEvent			The auxillary power supply voltage is out of specified operating range.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.102	NodenewTemperatureChangeEvent			Temperature change detected since last report. The possible temperature states are OK, High, and Very High.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.103	NodenewPciErrorsEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.104	NodenewMemoryParityErrorsEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.105	NodepciBusInterfaceErrorEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.106	NodefcInterfaceFailureEvent			Fibre Channel interface failed Health Check.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.107	NodescsiInterfaceFailureEvent			SCSI interface failed Health Check.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.108	NodessaInterfaceFailureEvent			SSA interface failed Health Check.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.109	NodedeviceFailureEvent			Target device failed Health Check.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.110	NodefcLinkStatusChangeEvent			Fibre Channel link status has changed.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.111	NodenewFcTranferErrorsEvent			New Fibre Channel transfer errors were detected since last report.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.112	NodeenvFanEvent			The health check task has detected a fan running in warning or alarm range.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.113	NodeenvPowerEvent			The health check task has detected a power supply running in warning or alarm range.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.114	NodeenvTemperatureEvent			The health check task has detected a temperature sensor reporting in warning or alarm range.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.115	NodeeccMemoryHealthCheckEvent			The health check task has detected an ECC memory error.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.116	NodeeccMemoryScrubberEvent			The health check task has detected an ECC memory scrubber event.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.118	NodedeviceRecoverEvent
1.3.6.1.4.1.3764.1.1.400.10.10.1000.150	NodelogWillOverwriteEvent			The event log circular buffer is about to wrap, overwriting the oldest entries.
1.3.6.1.4.1.3764.1.1.400.10.10.1000.4444	NodebootCompletedEvent			This unit has completed its boot sequence and is ready for SNMP communication with management applications. During the time period between the initiation of th…

Type Definitions

Name	Syntax	Status	Description
Boolean	INTEGER { true(1), false(2) }
DeviceType	INTEGER{ directAccess(0), sequentialAccess(1), printer(2), processor(3), worm(4), cd(5), scanner(6), opticalMemory(7), mediumChanger(8), communications(9), ascIt81(10), ascIt82(11), storageArrayController(12), enclosure(13), simplifiedDirectAccess(14), opticalCardReader(15), unknown(31) }
FcHPFPortFailType	INTEGER {none(0), linkDown(1), linkError(2)}
FcHPFPortState	INTEGER {onLine(0), offLine(1)}
FcHPFRecoveryType	INTEGER {returnToActive(0), returnToStandby(1), requiresIntervention(2)}
FcStatus	INTEGER { configWait(0), loopInit(1), login(2), ready(3), lostSync(4), error(5), reinit(6), nonPart(7), failed(8) }
FibreConnOptions	INTEGER{ loopOnly(0), pointToPointOnly(1), loopPreferred(2), pointToPointPreferred(3) }
FibreLoopIDMode	INTEGER{ soft(0) , hard(1) }
FibreMedia	INTEGER{ unknown(0), copper(1), shortWaveOptical(2), longWaveOptical(3), shortWaveOpticalDual(4) , longWaveOpticalDual(5), shortWaveOpticalLongDistance(6) , longWaveOpticalLongDistance(7), gbicSWOneGB(8), gbicLW1300OneGB(9), gbicLW1300HPOneGB(10), gbicLW1550HPOneGB(11), gbicCopperHSSDCOneGB(12), gbicCopperDB9OneGB(13), gbicSWTwoGB(14), gbicLW1300TwoGB(15), gbicLW1300HPTwoGB(16), gbicLW1550HPTwoGB(17), gbicCopperHSSDCTwoGB(18), gbicCopperDB9TwoGB(19), noGBIC(20) , sfpSWTwoGB(21) }
FibrePort	INTEGER{ nodeLoop(0) , node(1) , fabricLoop(3), fabric(4), none( 255 ) }
FibrePortMode	INTEGER{ privateTargetOnly(1), privateInitiatorOnly(2), privateTargetAndInitiator(3), publicTargetOnly(17), publicInitiatorOnly(18), publicTargetAndInitiator(19) }
HostLUNType	INTEGER {bit8(0), bit16(1), vsa(2)}
Interface	INTEGER { none(0), sanGateway(1), ssa(2), fibreChannel(3), scsi(4), ethernet(5), unknown(6), any(7) , sanReplication(8), vLib(9), soip(10), soip2(11) }
PathlightProduct	INTEGER{ sanGateway(1) , sanRouter(2) , sanBridge(3), adicFCR2(4), dellFCR2(5), siemensFCR2(6), sanHoneoye(7), adicHoneoye(8), dellHoneoye(9), siemensHoneoye(10), ibmGatewayModule(11), ibmHoneoye(12), adicPlt5000(13), dellPlt5000(14), ibmPlt5000(15), adicSNC4000(16), dellSNC4000(17), adicSNC6101(18), dellSNC6101(19), adicSNC6404(20), adicSNC6104(21) }
PltStatus	INTEGER { failed(1), down(2), testing(3), up(4) }
Reset	INTEGER { run(0) , reset(1) , reboot(2) }
RowStatus	INTEGER { active(1), notInService(2), notReady(3), createAndGo(4), createAndWait(5), destroy(6) }
ScsiAnsiLevel	INTEGER{ notScsi(0) , scsi-1(1), scsi-2(2) , scsi-3(3) }
ScsiCardType	INTEGER{ none(0), differentialNoTermination(1), differentialTerminated(2), singleEndedNoTermination(3), singleEndedTerminated(4), unknown(5), lowVoltageSingleEnded(6), lowVoltageDifferential(7), lowVoltageMultiFunction(8) }
ScsiSpeed	INTEGER { async(0), fast(1), ultra(2) , ultra2(3) , ultra160(4) , ultra320(5) }
VendorIDInt	INTEGER{ unknown(0) , symbios(4096) , amd(4130) , qlogic(4215) , pathlight(4537) }

MIB Viewer

What's a MIB?

What's SNMP?

What's an OID?

SNMP Fundamentals

Using net-snmp

Configuring SNMP on Cisco devices

Configuring SNMP on Fortinet devices

Understanding MIBs

Troubleshooting SNMP

Searching OIDs

Modem/MTA bootfiles

DOCSIS Monitoring

Linux snmpd passthrough

ADIC-SANMGR-PROXY-MIB

Bulk Translate

Search Vendor MIBs

Search Vendor Traps