ARICENT-ISS-ACL-MIB
121 objects
The MIB for AricentISSAcessControl.
Imported Objects
| INET-ADDRESS-MIB | InetAddress InetAddressPrefixLength InetAddressType |
| SNMPv2-SMI | Counter32 enterprises Integer32 MODULE-IDENTITY OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DisplayString MacAddress RowStatus TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.29601.2.21 | IdentityissAcl | The MIB for AricentISSAcessControl. | ||
| 1.3.6.1.4.1.29601.2.21.1 | ScalarAn | current | A simple status value for the object. | |
| 1.3.6.1.4.1.29601.2.21.1 | NodeissAclRateControl | |||
| 1.3.6.1.4.1.29601.2.21.1.1 | TableissAclRateCtrlTable | not-accessible | current | This object specifies a table to control the rate limiting parameters either for the entire switch or for each interface in the switch. |
| 1.3.6.1.4.1.29601.2.21.1.1.1 | RowissAclRateCtrlEntry | not-accessible | current | This object specifies an entry which appears in this table for each physical interface in the switch. |
| 1.3.6.1.4.1.29601.2.21.1.1.1.1 | ColumnissAclRateCtrlIndex | not-accessible | current | This object specifies the interface index for which the configuration in this entry applies. |
| 1.3.6.1.4.1.29601.2.21.1.1.1.2 | ColumnissAclRateCtrlDLFLimitValue | read-write | current | This object is used to configure the limiting value for the maximum number of dlf packets that can be transmitted per second over this interface. Setting this … |
| 1.3.6.1.4.1.29601.2.21.1.1.1.3 | ColumnissAclRateCtrlBCASTLimitValue | read-write | current | This object is used to configure the limiting value for the maximum number of broadcast packets that can be transmitted per second over this interface. Setting… |
| 1.3.6.1.4.1.29601.2.21.1.1.1.4 | ColumnissAclRateCtrlMCASTLimitValue | read-write | current | This object is used to configure the limiting value for the maximum number of multicast packets that can be transmitted per second over this interface. Setting… |
| 1.3.6.1.4.1.29601.2.21.1.1.1.5 | ColumnissAclRateCtrlPortRateLimit | read-write | current | This object is used to configure interface Rate Limit (Packet that can be transferred on a port at a particular second). This object's value will take effect o… |
| 1.3.6.1.4.1.29601.2.21.1.1.1.6 | ColumnissAclRateCtrlPortBurstSize | read-write | current | this object is used to configure interface Burst Pkt Rate. (Packet Burst that can be transferred on a port at a particular second) This object's value will tak… |
| 1.3.6.1.4.1.29601.2.21.2 | NodeissAclL2Filter | |||
| 1.3.6.1.4.1.29601.2.21.2.1 | TableissAclL2FilterTable | not-accessible | current | This object specifies the table which is used to configure L2 filter rules in the system. |
| 1.3.6.1.4.1.29601.2.21.2.1.1 | RowissAclL2FilterEntry | not-accessible | current | This object specifies that each entry in this table is a L2 filter rule. Index to the table is the L2 filter number. |
| 1.3.6.1.4.1.29601.2.21.2.1.1.1 | ColumnissAclL2FilterNo | not-accessible | current | This object specifies the L2 Filter rule number. |
| 1.3.6.1.4.1.29601.2.21.2.1.1.2 | ColumnissAclL2FilterPriority | read-write | current | This object specifies the priority of the L2 filter can be used to decide which filter rule is applicable when Higher value of 'filter priority' implies a high… |
| 1.3.6.1.4.1.29601.2.21.2.1.1.3 | ColumnissAclL2FilterEtherType | read-write | current | This object specifies the value in the Type/Len field of a frame that will be matched to trigger this filter. The default value of this object is '0'. When thi… |
| 1.3.6.1.4.1.29601.2.21.2.1.1.4 | ColumnissAclL2FilterProtocolType | read-write | current | This object specifies the non IP protocol type to be filtered. aarp | amber | dec-spanning | decnet-iv | diagnostic | dsm |etype-6000 | etype-8042 | lat | lavc… |
| 1.3.6.1.4.1.29601.2.21.2.1.1.5 | ColumnissAclL2FilterDstMacAddr | read-write | current | This object specifies that the Destination MAC address to be matched with the packet. By Default, the Destination Mac Address will be zero which means dont car… |
| 1.3.6.1.4.1.29601.2.21.2.1.1.6 | ColumnissAclL2FilterSrcMacAddr | read-write | current | This object specifies that the Source MAC address to be matched with the packet. By Default, the Source Mac Address will be zero which means dont care conditio… |
| 1.3.6.1.4.1.29601.2.21.2.1.1.7 | ColumnissAclL2FilterVlanId | read-write | current | This object specifies that the Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will be treated as customer Vlan Id. A value of '0' means, thi… |
| 1.3.6.1.4.1.29601.2.21.2.1.1.8 | ColumnissAclL2FilterInPortList | read-write | current | This object specifies the complete set of ports over which this filter is applied for packets ingress at ports in this list. If the In port list is '0', the fi… |
| 1.3.6.1.4.1.29601.2.21.2.1.1.9 | ColumnissAclL2FilterAction | read-write | current | This object specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be forwarded according to the … |
| 1.3.6.1.4.1.29601.2.21.2.1.1.10 | ColumnissAclL2FilterMatchCount | read-only | current | This object specifies the number of times this filter is matched. |
| 1.3.6.1.4.1.29601.2.21.2.1.1.11 | ColumnissAclL2FilterStatus | read-create | current | This object specifies the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.29601.2.21.2.1.1.12 | ColumnissAclL2FilterOutPortList | read-write | current | This object specifies the complete set of ports over which this filter is applied for packets egress at Ports in this list. If the Out port list is '0', the fi… |
| 1.3.6.1.4.1.29601.2.21.2.1.1.13 | ColumnissAclL2FilterDirection | read-write | current | This object specifies the direction of this filter to be applied. By Default the filter will be applied on ingress direction. When the direction of this filter… |
| 1.3.6.1.4.1.29601.2.21.2.1.1.14 | ColumnissAclL2FilterSubAction | read-write | current | This object specifies that the action to be taken on the incoming packet is detailed below - none - no action modifyVlan - Traffic matching ACL rule will have … |
| 1.3.6.1.4.1.29601.2.21.2.1.1.15 | ColumnissAclL2FilterSubActionId | read-write | current | This object specifies that the Id to be used if the object as specified by issAclL2FilterSubAction is either modifyvlan or nestedvlan only. Non-Zero value need… |
| 1.3.6.1.4.1.29601.2.21.2.1.1.16 | ColumnissAclL2FilterRedirectId | read-only | current | This object specifies the redirect index associated with L2Filter entry. |
| 1.3.6.1.4.1.29601.2.21.2.1.1.17 | ColumnissAclL2NextFilterNo | read-write | current | This object specifies that the Next Filter rule number to be matched for traffic matching the current ACL rule |
| 1.3.6.1.4.1.29601.2.21.2.1.1.18 | ColumnissAclL2NextFilterType | read-write | current | This object specifies the type of the next access-control list. The type could take the value 'l2filter' for MAC-based ACLs and 'l3filter' for IP-based ACLs. I… |
| 1.3.6.1.4.1.29601.2.21.2.1.1.19 | ColumnissAclL2FilterCfiDeiBit | read-write | current | This object specifies the CfiDei bit value in the c-vlan tag or s-vlan tag of the packet to be applied in the filter. |
| 1.3.6.1.4.1.29601.2.21.2.1.1.20 | ColumnissAclL2FilterDP | read-write | current | This object specifies the drop precedence level to be applied in the filter. |
| 1.3.6.1.4.1.29601.2.21.2.1.1.21 | ColumnissAclL2FilterRestore | read-write | current | This object stores the order of PCL index while storing the configurations. |
| 1.3.6.1.4.1.29601.2.21.2.1.1.22 | ColumnissAclL2FilterDstMacAddrMask | read-write | current | This object specifies that the mask used to match the Destination MAC address with the packet. By Default, the Destination Mac Address Mask will be ff:ff:ff:ff… |
| 1.3.6.1.4.1.29601.2.21.2.1.1.23 | ColumnissAclL2FilterSrcMacAddrMask | read-write | current | This object specifies that the mask used to match the Source MAC address with the packet. By Default, the Source Mac Address Mask will be ff:ff:ff:ff:ff:ff whi… |
| 1.3.6.1.4.1.29601.2.21.3 | NodeissAclL3Filter | |||
| 1.3.6.1.4.1.29601.2.21.3.1 | TableissAclL3FilterTable | not-accessible | current | This object specifies a table to configure L3 filter rules in the system. |
| 1.3.6.1.4.1.29601.2.21.3.1.1 | RowissAclL3FilterEntry | not-accessible | current | This object specifies that each entry in this table is a L3 filter rule. Index to the table is L3 filter number. |
| 1.3.6.1.4.1.29601.2.21.3.1.1.1 | ColumnissAclL3FilterNo | not-accessible | current | L3 Filter rule number. |
| 1.3.6.1.4.1.29601.2.21.3.1.1.2 | ColumnissAclL3FilterPriority | read-write | current | This object specifies that the priority of the filter can be used to decide which filter rule is applicable when Higher value of 'L3 filter priority' implies a… |
| 1.3.6.1.4.1.29601.2.21.3.1.1.3 | ColumnissAclL3FilterProtocol | read-write | current | This object specifies the type of protocol to be checked against the packet. The default value is 255. If the value is 255, it means that the protocol type can… |
| 1.3.6.1.4.1.29601.2.21.3.1.1.4 | ColumnissAclL3FilterMessageType | read-write | current | This object specifies the message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed… |
| 1.3.6.1.4.1.29601.2.21.3.1.1.5 | ColumnissAclL3FilterMessageCode | read-write | current | This object specifies the message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed… |
| 1.3.6.1.4.1.29601.2.21.3.1.1.6 | ColumnissAclL3FilteAddrType | read-create | current | This object specifies the type of IP address used by this classifier entry. While other types of addresses are defined in the InetAddressType textual conventio… |
| 1.3.6.1.4.1.29601.2.21.3.1.1.7 | ColumnissAclL3FilterDstIpAddr | read-create | current | This object specifies the IP address to match against the packet's destination IP address. This may not be a DNS name, but may be an IPv4 or IPv6 prefix. issAc… |
| 1.3.6.1.4.1.29601.2.21.3.1.1.8 | ColumnissAclL3FilterSrcIpAddr | read-create | current | This object specifies the IP address to match against the packet's source IP address. This may not be a DNS name, but may be an IPv4 or IPv6 prefix. issAclL3Fi… |
| 1.3.6.1.4.1.29601.2.21.3.1.1.9 | ColumnissAclL3FilterDstIpAddrPrefixLength | read-create | current | This object specifies the length of the CIDR Prefix carried in issAclL3FilterDstIpAddr. In IPv4 addresses, a length of 0 indicates a match of any address; a le… |
| 1.3.6.1.4.1.29601.2.21.3.1.1.10 | ColumnissAclL3FilterSrcIpAddrPrefixLength | read-create | current | This object specifies the length of the CIDR Prefix carried in issAclL3FilterSrcIpAddr. In IPv4 addresses, a length of 0 indicates a match of any address; a le… |
| 1.3.6.1.4.1.29601.2.21.3.1.1.11 | ColumnissAclL3FilterMinDstProtPort | read-write | current | This object specifies the minimum port in the destination port range. Please note these ports are the TCP / UDP ports. |
| 1.3.6.1.4.1.29601.2.21.3.1.1.12 | ColumnissAclL3FilterMaxDstProtPort | read-write | current | This object specifies the maximum port in the destination port range. Please note these ports are the TCP / UDP ports. |
| 1.3.6.1.4.1.29601.2.21.3.1.1.13 | ColumnissAclL3FilterMinSrcProtPort | read-write | current | This object specifies the minimum port in the source port range. Please note these ports are the TCP / UDP ports. |
| 1.3.6.1.4.1.29601.2.21.3.1.1.14 | ColumnissAclL3FilterMaxSrcProtPort | read-write | current | This object specifies the maximum port in the source port range. Please note these ports are the TCP / UDP ports. |
| 1.3.6.1.4.1.29601.2.21.3.1.1.15 | ColumnissAclL3FilterInPortList | read-write | current | This object specifies the complete set of ports over which if the packet arrives this filter rule will be applicable. If the In port list is '0', the filter ru… |
| 1.3.6.1.4.1.29601.2.21.3.1.1.16 | ColumnissAclL3FilterOutPortList | read-write | current | This object specifies the complete set of ports over which if the packet goes out, this filter rule will be applicable. If the outgoing port list is '0', the f… |
| 1.3.6.1.4.1.29601.2.21.3.1.1.17 | ColumnissAclL3FilterAckBit | read-create | current | This object specifies the TCP ACK bit to be checked against the packet. The default value is 'any'(3). It means that ACK bit will not be checked to decide the … |
| 1.3.6.1.4.1.29601.2.21.3.1.1.18 | ColumnissAclL3FilterRstBit | read-create | current | This object specifies the TCP RST bit to be checked against the packet. The default value is 'any'(3). It means that RST bit will not be checked to decide the … |
| 1.3.6.1.4.1.29601.2.21.3.1.1.19 | ColumnissAclL3FilterTos | read-create | current | This object specifies that the IP TOS bit to be checked against the packet. This is a single byte integer of which the last three bits (least significant bits)… |
| 1.3.6.1.4.1.29601.2.21.3.1.1.20 | ColumnissAclL3FilterDscp | read-create | current | This object specifies that the IP Dscp value to be checked against the packet. A value of '-1' means, the Dscp Field becomes dont care. |
| 1.3.6.1.4.1.29601.2.21.3.1.1.21 | ColumnissAclL3FilterDirection | read-write | current | This object specifies the direction of this filter to be applied. By Default the filter will be applied on ingress direction. When the direction of this filter… |
| 1.3.6.1.4.1.29601.2.21.3.1.1.22 | ColumnissAclL3FilterAction | read-write | current | This object specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be sent to the ports in 'out p… |
| 1.3.6.1.4.1.29601.2.21.3.1.1.23 | ColumnissAclL3FilterMatchCount | read-only | current | This object specifies the number of times this filter is matched. |
| 1.3.6.1.4.1.29601.2.21.3.1.1.24 | ColumnissAclL3FilterFlowId | read-create | current | This object specifies the flow identifier in an IPv6 header. |
| 1.3.6.1.4.1.29601.2.21.3.1.1.25 | ColumnissAclL3FilterStatus | read-create | current | This object specifies the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used w… |
| 1.3.6.1.4.1.29601.2.21.3.1.1.26 | ColumnissAclL3FilterSubAction | read-write | current | This object specifies the action that is to be taken on the incoming packet value specified by this object is detailed below - none - no action modifyVlan - Tr… |
| 1.3.6.1.4.1.29601.2.21.3.1.1.27 | ColumnissAclL3FilterSubActionId | read-write | current | This object specifies the Id to be used if the object as specified by issAcl3FilterSubAction is either modifyvlan or nestedvlan only. Non-Zero value need to be… |
| 1.3.6.1.4.1.29601.2.21.3.1.1.28 | ColumnissAclL3FilterRedirectId | read-only | current | This object specifies the redirect index associated with L3Filter entry. |
| 1.3.6.1.4.1.29601.2.21.3.1.1.29 | ColumnissAclL3FilterRestore | read-write | current | This object is used to store the order of PCL index while storing the configurations. |
| 1.3.6.1.4.1.29601.2.21.3.1.1.30 | ColumnissAclL3FilterSynBit | read-create | current | This object specifies the SYN RST bit to be checked against the packet. The default value is 'any'(3). It means that SYN bit will not be checked to decide the … |
| 1.3.6.1.4.1.29601.2.21.4 | NodeissAclUserDefinedFilter | |||
| 1.3.6.1.4.1.29601.2.21.4.1 | TableissAclUserDefinedFilterTable | not-accessible | current | This object specifies the table which is used to configure user defined filter rules in the system. This table is used for specifying the user defined packet h… |
| 1.3.6.1.4.1.29601.2.21.4.1.1 | RowissAclUserDefinedFilterEntry | not-accessible | current | This object specifies the user defined filter entry indexed uniquely by issAclUserDefinedFilterId. |
| 1.3.6.1.4.1.29601.2.21.4.1.1.1 | ColumnissAclUserDefinedFilterId | not-accessible | current | This object specifies an Index to uniquely identify the User defined filter table entry. |
| 1.3.6.1.4.1.29601.2.21.4.1.1.2 | ColumnissAclUserDefinedFilterPktType | read-write | current | This object specifies the type of packet for which packet-filter match needs to be applied on incoming traffic. |
| 1.3.6.1.4.1.29601.2.21.4.1.1.3 | ColumnissAclUserDefinedFilterOffSetBase | read-write | current | This object specifies the offset base from the start of packet header ( beginning of full packet) for which the match needs to be applied on incoming traffic. … |
| 1.3.6.1.4.1.29601.2.21.4.1.1.4 | ColumnissAclUserDefinedFilterOffSetValue | read-write | current | This object specifies the offset value for which packet-filter match needs to be applied on incoming traffic. A value of zero indicates that this field is dont… |
| 1.3.6.1.4.1.29601.2.21.4.1.1.5 | ColumnissAclUserDefinedFilterOffSetMask | read-write | current | This object specifies the mask for the offset value. The actual user defined value to be used for matching incoming traffic is obtained after ANDing the Offset… |
| 1.3.6.1.4.1.29601.2.21.4.1.1.6 | ColumnissAclUserDefinedFilterPriority | read-write | current | This object specifies the priority of the filter that can be used to decide which filter rule is applicable when Higher value of 'UserDefined filter priority' … |
| 1.3.6.1.4.1.29601.2.21.4.1.1.7 | ColumnissAclUserDefinedFilterAction | read-write | current | |
| 1.3.6.1.4.1.29601.2.21.4.1.1.8 | ColumnissAclUserDefinedFilterInPortList | read-write | current | This object specifies the complete set of ports over which this filter is applied for packets ingress at ports in this list. Filter will be applied in chip whe… |
| 1.3.6.1.4.1.29601.2.21.4.1.1.9 | ColumnissAclUserDefinedFilterIdOneType | read-write | current | This Object specifies the type of the Base ACL rule 1 that is used for deriving new ACL rule. |
| 1.3.6.1.4.1.29601.2.21.4.1.1.10 | ColumnissAclUserDefinedFilterIdOne | read-write | current | This Object specifies the ID of the Base ACL rule 1 (MAC-based or IP-based) that is used for deriving new ACL rule. |
| 1.3.6.1.4.1.29601.2.21.4.1.1.11 | ColumnissAclUserDefinedFilterIdTwoType | read-write | current | This Object specifies the type of the Base ACL rule 2 that is used for deriving new ACL rule. |
| 1.3.6.1.4.1.29601.2.21.4.1.1.12 | ColumnissAclUserDefinedFilterIdTwo | read-write | current | This Object specifies the ID of the Base ACL rule 2 (MAC-based or IP-based) that is used for deriving new ACL rule. |
| 1.3.6.1.4.1.29601.2.21.4.1.1.13 | ColumnissAclUserDefinedFilterSubAction | read-write | current | This object specifies the action that is to be taken on the incoming packet is detailed below - none - no action modifyVlan - Traffic matching ACL rule will ha… |
| 1.3.6.1.4.1.29601.2.21.4.1.1.14 | ColumnissAclUserDefinedFilterSubActionId | read-write | current | Id to be used if the object as specified by issAclUserDefinedFilterSubAction is either modifyvlan or nestedvlan only. Non-Zero value need to be specify when is… |
| 1.3.6.1.4.1.29601.2.21.4.1.1.15 | ColumnissAclUserDefinedFilterRedirectId | read-only | current | This object specifies the redirect index associated with UserDefinedFilter entry. |
| 1.3.6.1.4.1.29601.2.21.4.1.1.16 | ColumnissAclUserDefinedFilterStatus | read-create | current | This object speifies the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used wh… |
| 1.3.6.1.4.1.29601.2.21.5 | NodeissRedirectInterfaceGrp | |||
| 1.3.6.1.4.1.29601.2.21.5.1 | TableissRedirectInterfaceGrpTable | not-accessible | current | This object specifies an interface group which is a collection of physical ports ( or ) trunks that are grouped together for distributing traffic received on a… |
| 1.3.6.1.4.1.29601.2.21.5.1.1 | RowissRedirectInterfaceGrpEntry | not-accessible | current | This object specifies that there is one entry in this table for each created Interface-Group. An interface-group/virtual trunk is uniquely identified by the ob… |
| 1.3.6.1.4.1.29601.2.21.5.1.1.1 | ColumnissRedirectInterfaceGrpId | not-accessible | current | This object specifies an Index to the Redirect Interface Group table entry. Uniquely identifies the interface-group. |
| 1.3.6.1.4.1.29601.2.21.5.1.1.2 | ColumnissRedirectInterfaceGrpFilterType | read-write | current | This object specifies the type of the access-control list. The type could take the value 'l2filter' for MAC-based ACLs and 'l3filter' for IP-based ACLs. It tak… |
| 1.3.6.1.4.1.29601.2.21.5.1.1.3 | ColumnissRedirectInterfaceGrpFilterId | read-write | current | This Object specifies the ID of the MAC-based, IP-based or UserDefined access control list/filter-rule, the details of which should be matched against the inco… |
| 1.3.6.1.4.1.29601.2.21.5.1.1.4 | ColumnissRedirectInterfaceGrpDistByte | read-write | current | This object specifies the Distribution Byte that needs to be used for deriving the traffic distribution hash-logic for the set of interfaces in the interface-g… |
| 1.3.6.1.4.1.29601.2.21.5.1.1.5 | ColumnissRedirectInterfaceGrpPortList | read-write | current | Each octet in this object specifies the IfIndex of a physical interface or manually aggregated trunk.Based on the value specified by issRedirectInterfaceGrpTyp… |
| 1.3.6.1.4.1.29601.2.21.5.1.1.6 | ColumnissRedirectInterfaceGrpType | read-write | current | This object specifies whether the redirected interface is a single port or portlist.If the value of this object is port(1) then the redirected interface is a s… |
| 1.3.6.1.4.1.29601.2.21.5.1.1.7 | ColumnissRedirectInterfaceGrpUdbPosition | read-write | current | This object specifies the User defined postion of a byte in the packet when the value of the object as specified by issRedirectInterfaceGrpDistByte is udb. |
| 1.3.6.1.4.1.29601.2.21.5.1.1.8 | ColumnissRedirectInterfaceGrpStatus | read-create | current | This object specifies the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry is 'not-ready' when the… |
| 1.3.6.1.4.1.29601.2.21.6 | NodeissRedirectIdNextFree | |||
| 1.3.6.1.4.1.29601.2.21.6.1 | ScalarissRedirectInterfaceGrpIdNextFree | read-only | current | This object value the next free index (issRedirectInterfaceGrpId) to be used for creation of redirect interface entry, or a zero to indicate that none exist |
| 1.3.6.1.4.1.29601.2.21.7 | NodeissReservedFrameGrp | |||
| 1.3.6.1.4.1.29601.2.21.7.1 | TableissReservedFrameCtrlTable | not-accessible | current | A table to configure IEEE802 Reserved Multicast-MAC Address filter rules in the system. The reserved transmission control function is a function that takes fra… |
| 1.3.6.1.4.1.29601.2.21.7.1.1 | RowissReservedFrameCtrlEntry | not-accessible | current | An Reserved-Frame-Tranmission-Entry is uniquely identified by the object 'issReservedFrameTxnCtrlId'. |
| 1.3.6.1.4.1.29601.2.21.7.1.1.1 | ColumnissReservedFrameCtrlId | not-accessible | current | Index to the ReservedFrameTxnCtrl entry. Uniquely identifies the issReservedFrameTxnCtrl entry. |
| 1.3.6.1.4.1.29601.2.21.7.1.1.2 | ColumnissReservedFrameCtrlPktType | read-write | current | This object specifies the type of the PDUs. The type could take the following values bpdu - (MAC:01:80:C2:00:00:00) for Suppressing BPDU CPU transfer (Cannot b… |
| 1.3.6.1.4.1.29601.2.21.7.1.1.3 | ColumnissReservedFrameCtrlAction | read-write | current | |
| 1.3.6.1.4.1.29601.2.21.7.1.1.4 | ColumnissReservedFrameCtrlOtherMacAddr | read-write | current | Reserved Destination Multicast MAC address to be matched with the packet |
| 1.3.6.1.4.1.29601.2.21.7.1.1.5 | ColumnissReservedFrameCtrlOtherMacMask | read-write | current | The range of Mac addresses will be decided based on the Mask Specified. The possible masks are : Mask Value MAC addresses 0xff 1 0xfe 2 0xfc 4 0xf8 8 0xf0 16 0… |
| 1.3.6.1.4.1.29601.2.21.7.1.1.6 | ColumnissReservedFrameCtrlMatchCount | read-only | current | Number of times this ReservedFrameCtrl-entry is matched. |
| 1.3.6.1.4.1.29601.2.21.7.1.1.7 | ColumnissReservedFrameCtrlStatsEnabledStatus | read-write | current | This object specifies the status of ReservedFrameCtrl-entry statistics collection. When set as enabled, the number of hits for the specific entry is collected … |
| 1.3.6.1.4.1.29601.2.21.7.1.1.8 | ColumnissClearReservedFrameCtrlStats | read-write | current | This object clears the hit count of the specific ReservedFrameCtrl-entry. When this object is set as 'true'(1), the hit count for the filter is cleared and the… |
| 1.3.6.1.4.1.29601.2.21.7.1.1.9 | ColumnissReservedFrameCtrlStatus | read-create | current | This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry is 'not-ready' when the… |
| 1.3.6.1.4.1.29601.2.21.8 | NodeissAclTrc | |||
| 1.3.6.1.4.1.29601.2.21.8.1 | ScalarissAclTrcFlag | read-write | current | This object is used to enable trace statements in Acl module. A four byte integer is used for enabling the trace level. Each bit in the four byte integer repre… |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| EnabledStatus | INTEGER { enabled(1), disabled(2) } | current | A simple status value for the object. |
| IndexInteger | Unsigned32 (1..65535) | current | An integer which may be used as a table index. If 0 then it is invalid. |
| IndexIntegerNextFree | always contains a legal value (if non-zero) for an index that is not currently used in the relevant table. The Command Generator (Network Management Application) reads this variable and uses the (non-zero) value read when creating a new row with an SNMP SET. When the SET is performed, the Command Responder (agent) must determine whether the value is indeed still unused; Two Network Management Applications may attempt to create a row (configuration entry) simultaneously and use the same value. If it is currently unused, the SET succeeds and the Command Responder (agent) changes the value of this object, according to an implementation-specific algorithm. If the value is in use, however, the SET fails. The Network Management Application must then re-read this variable to obtain a new usable value. | current | |
| PortList | OCTET STRING | current | Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents… |
| ReservedFrameType | INTEGER { bpdu (1), lacpdu-udld (2), eap (3), lldpdu (4), other (5), all (6) } | current | IfDirection specifies a direction of data travel on an transmission on the interface. |