BIANCA-BRICK-FR-MIB
55 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | Counter enterprises |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.10.32 | Nodefrpublic | |||
| 1.3.6.1.2.1.10.32.1 | TablefrDlcmiTable | not-accessible | mandatory | The Parameters for the Data Link Connection Management Interface for the frame relay service on this interface. |
| 1.3.6.1.2.1.10.32.1.1 | RowfrDlcmiEntry | not-accessible | mandatory | The Parameters for a particular Data Link Con- nection Management Interface. |
| 1.3.6.1.2.1.10.32.1.1.1 | ColumnfrDlcmiIfIndex | read-only | mandatory | The ifIndex value of the corresponding ifEn- try. |
| 1.3.6.1.2.1.10.32.1.1.2 | ColumnfrDlcmiState | read-write | mandatory | This variable states which Data Link Connec- tion Management scheme is active (and by impli- cation, what DLCI it uses) on the Frame Relay interface. |
| 1.3.6.1.2.1.10.32.1.1.3 | ColumnfrDlcmiAddress | read-write | mandatory | This variable states which address format is in use on the Frame Relay interface. |
| 1.3.6.1.2.1.10.32.1.1.4 | ColumnfrDlcmiAddressLen | read-write | mandatory | This variable states which address length in octets. In the case of Q922 format, the length indicates the entire length of the address in- cluding the control … |
| 1.3.6.1.2.1.10.32.1.1.5 | ColumnfrDlcmiPollingInterval | read-write | mandatory | This is the number of seconds between succes- sive status enquiry messages. |
| 1.3.6.1.2.1.10.32.1.1.6 | ColumnfrDlcmiFullEnquiryInterval | read-write | mandatory | Number of status enquiry intervals that pass before issuance of a full status enquiry mes- sage. |
| 1.3.6.1.2.1.10.32.1.1.7 | ColumnfrDlcmiErrorThreshold | read-write | mandatory | This is the maximum number of unanswered Status Enquiries the equipment shall accept be- fore declaring the interface down. |
| 1.3.6.1.2.1.10.32.1.1.8 | ColumnfrDlcmiMonitoredEvents | read-write | mandatory | This is the number of status polling intervals over which the error threshold is counted. For example, if within 'MonitoredEvents' number of events the station… |
| 1.3.6.1.2.1.10.32.1.1.9 | ColumnfrDlcmiMaxSupportedVCs | read-write | mandatory | The maximum number of Virtual Circuits allowed for this interface. Usually dictated by the Frame Relay network. In response to a SET, if a value less than zero… |
| 1.3.6.1.2.1.10.32.1.1.10 | ColumnfrDlcmiMulticast | read-write | mandatory | This indicates whether the Frame Relay inter- face is using a multicast service. |
| 1.3.6.1.2.1.10.32.1.1.42 | ColumnfrDlcmiDceIdleInterval | read-write | mandatory | This is the number of seconds within a status enquiry messages should be received. |
| 1.3.6.1.2.1.10.32.1.1.43 | ColumnfrDlcmiDceErrorThreshold | read-write | mandatory | This is the maximum number of unsent Status Enquiries the equipment shall accept be- fore declaring the interface down. |
| 1.3.6.1.2.1.10.32.1.1.44 | ColumnfrDlcmiDceMonitoredEvents | read-write | mandatory | This is the number of status polling intervals over which the error threshold is counted. For example, if within 'MonitoredEvents' number of events the station… |
| 1.3.6.1.2.1.10.32.1.1.45 | ColumnfrDlcmiMode | read-write | mandatory | This indicates the mode of the interface. dte(1) does status enquiry polling, dce(2) does status answering. nni(3) is bidirectional use of both dte and dce. |
| 1.3.6.1.2.1.10.32.1.1.46 | ColumnfrDlcmiDefaultRouteIfIndex | read-write | mandatory | This is the default route interface index when a new PVC is established by means of line management. |
| 1.3.6.1.2.1.10.32.2 | TablefrCircuitTable | not-accessible | mandatory | A table containing information about specific Data Link Connection Identifiers and corresponding virtual circuits. |
| 1.3.6.1.2.1.10.32.2.1 | RowfrCircuitEntry | not-accessible | mandatory | The information regarding a single Data Link Connection Identifier. |
| 1.3.6.1.2.1.10.32.2.1.1 | ColumnfrCircuitIfIndex | read-write | mandatory | The ifIndex Value of the ifEntry this virtual circuit is layered onto. |
| 1.3.6.1.2.1.10.32.2.1.2 | ColumnfrCircuitDlci | read-write | mandatory | The Data Link Connection Identifier for this virtual circuit. |
| 1.3.6.1.2.1.10.32.2.1.3 | ColumnfrCircuitState | read-write | mandatory | Indicates whether the particular virtual cir- cuit is operational. In the absence of a Data Link Connection Management Interface, virtual circuit entries (rows… |
| 1.3.6.1.2.1.10.32.2.1.4 | ColumnfrCircuitReceivedFECNs | read-only | mandatory | Number of frames received from the network in- dicating forward congestion since the virtual circuit was created. |
| 1.3.6.1.2.1.10.32.2.1.5 | ColumnfrCircuitReceivedBECNs | read-only | mandatory | Number of frames received from the network in- dicating backward congestion since the virtual circuit was created. |
| 1.3.6.1.2.1.10.32.2.1.6 | ColumnfrCircuitSentFrames | read-only | mandatory | The number of frames sent from this virtual circuit since it was created. |
| 1.3.6.1.2.1.10.32.2.1.7 | ColumnfrCircuitSentOctets | read-only | mandatory | The number of octets sent from this virtual circuit since it was created. |
| 1.3.6.1.2.1.10.32.2.1.8 | ColumnfrCircuitReceivedFrames | read-only | mandatory | Number of frames received over this virtual circuit since it was created. |
| 1.3.6.1.2.1.10.32.2.1.9 | ColumnfrCircuitReceivedOctets | read-only | mandatory | Number of octets received over this virtual circuit since it was created. |
| 1.3.6.1.2.1.10.32.2.1.10 | ColumnfrCircuitCreationTime | read-only | mandatory | The value of sysUpTime when the virtual cir- cuit was created, whether by the Data Link Con- nection Management Interface or by a SetRe- quest. |
| 1.3.6.1.2.1.10.32.2.1.11 | ColumnfrCircuitLastTimeChange | read-only | mandatory | The value of sysUpTime when last there was a change in the virtual circuit state |
| 1.3.6.1.2.1.10.32.2.1.12 | ColumnfrCircuitCommittedBurst | read-write | mandatory | This variable indicates the maximum amount of data, in bits, that the network agrees to transfer under normal conditions, during the measurement interval. |
| 1.3.6.1.2.1.10.32.2.1.13 | ColumnfrCircuitExcessBurst | read-write | mandatory | This variable indicates the maximum amount of uncommitted data bits that the network will at- tempt to deliver over the measurement interval. By default, if no… |
| 1.3.6.1.2.1.10.32.2.1.14 | ColumnfrCircuitThroughput | read-write | mandatory | Throughput is the average number of 'Frame Re- lay Information Field' bits transferred per second across a user network interface in one direction, measured ov… |
| 1.3.6.1.2.1.10.32.2.1.42 | ColumnfrCircuitRouteType | read-only | mandatory | Type of routing entry. This field is intended for informational purpose only. |
| 1.3.6.1.2.1.10.32.2.1.43 | ColumnfrCircuitRouteIfIndex | read-write | mandatory | The destination IfIndex is a pointer to either a second frame relay interface (frame relay switching) or to a frame relay virtual interface (multiprotocol rout… |
| 1.3.6.1.2.1.10.32.2.1.44 | ColumnfrCircuitRouteDlci | read-write | mandatory | The destination DLCI. When the circuit is used for switching, all packets are sent using this DLCI. This field is void for multiprotocol routing. |
| 1.3.6.1.2.1.10.32.3 | TablefrErrTable | not-accessible | mandatory | A table containing information about Errors on the Frame Relay interface. |
| 1.3.6.1.2.1.10.32.3.1 | RowfrErrEntry | not-accessible | mandatory | The error information for a single frame relay interface. |
| 1.3.6.1.2.1.10.32.3.1.1 | ColumnfrErrIfIndex | read-only | mandatory | The ifIndex Value of the corresponding ifEn- try. |
| 1.3.6.1.2.1.10.32.3.1.2 | ColumnfrErrType | read-only | mandatory | The type of error that was last seen on this interface. |
| 1.3.6.1.2.1.10.32.3.1.3 | ColumnfrErrData | read-only | mandatory | An octet string containing as much of the er- ror packet as possible. As a minimum, it must contain the Q.922 Address or as much as was delivered. It is desira… |
| 1.3.6.1.2.1.10.32.3.1.4 | ColumnfrErrTime | read-only | mandatory | The value of sysUpTime at which the error was detected. |
| 1.3.6.1.2.1.10.32.4 | NodefrGlobals | |||
| 1.3.6.1.2.1.10.32.4.1 | ScalarfrTrapState | read-write | mandatory | This variable indicates whether the system produces the frDLCIStatusChange trap. |
| 1.3.6.1.4.1.272 | Nodebintec | |||
| 1.3.6.1.4.1.272.4 | Nodebibo | |||
| 1.3.6.1.4.1.272.4.13 | Nodefr | |||
| 1.3.6.1.4.1.272.4.13.1 | TablefrMprTable | not-accessible | mandatory | This table contains an entry for each frame relay DCE virtual interface. This interface is called virtual because it does not necessarily reflect to a single h… |
| 1.3.6.1.4.1.272.4.13.1.1 | RowfrMprEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.272.4.13.1.1.1 | ColumnfrMprIfIndex | read-write | mandatory | This object contains an interface index and assigns the row to an entry in ifTable. When creating new entries in the table, the value of this object shall be s… |
| 1.3.6.1.4.1.272.4.13.1.1.2 | ColumnfrMprMtu | read-write | mandatory | The Maximum transfer unit to be used with the interface (see also ifMtu). |
| 1.3.6.1.4.1.272.4.13.1.1.3 | ColumnfrMprEncapsulation | read-write | mandatory | This object specifies the encapsulation method to be used. If this object is set to mpr, the encapsulation method described in Q933a is used for the protocols … |
| 1.3.6.1.4.1.272.4.13.1.1.4 | ColumnfrMprIfcType | read-write | mandatory | This object specifies wether the interface is a multipoint(1) or a point-to-point(2) interface. |
| 1.3.6.1.4.1.272.4.13.1.1.5 | ColumnfrMprInverseArp | read-write | mandatory | This object specifies the use of Inverse Arp (as described in RFC 1490) to automatically detect upper layer network addresses. |