CXAsync-MIB
139 objects
No module-level DESCRIPTION found.
Imported Objects
| CXProduct-SMI | Alias cxAsync SapIndex ThruputClass |
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | Counter |
| RFC1213-MIB | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.495.2.1.6.30.1 | NodeasySapAlarm | Indicates that the global object asyStatusEvent has occurred at the identified SAP (service access point) if the global object asyAlarms is enabled. | ||
| 1.3.6.1.4.1.495.2.1.6.30.1 | ScalarasyX25TxQThreshold | read-write | mandatory | Defines the global X.25 queue threshold, in number of frames. When the threshold is exceeded and the SAP (service access point) object asySapNetworkFlowControl… |
| 1.3.6.1.4.1.495.2.1.6.30.2 | ScalarasyPadIdBanner | read-write | mandatory | Defines the Async PAD Identification Banner. This banner is transmitted to the attached device whenever it raises interface signals. Range of Values: 1 - 255 D… |
| 1.3.6.1.4.1.495.2.1.6.30.7 | ScalarasyAlarms | read-write | mandatory | Indicates whether this layer produces the object asySapAlarm trap. Options: disabled (1) enable (2) Default Value: disable Configuration Changed: Administrative |
| 1.3.6.1.4.1.495.2.1.6.30.8 | ScalarasySapStatusEvent | read-only | mandatory | Identifies the status generated in the object asyAlarmTrap. This object is used for identification by the trap when it occurs and will always return the value … |
| 1.3.6.1.4.1.495.2.1.6.30.9 | ScalarasySoftwareVersions | read-only | mandatory | Identifies the revision numbers of the Async layer software. This is a read-only parameter that displays the revision number as a string of five numbers. Each … |
| 1.3.6.1.4.1.495.2.1.6.30.10 | ScalarasyMibLevel | read-only | mandatory | Used to determine current MIB module release supported by the agent. Object is in decimal. |
| 1.3.6.1.4.1.495.2.1.6.30.20 | TableasySapTable | not-accessible | mandatory | Contains configuration information about each Async layer SAP (service access point). |
| 1.3.6.1.4.1.495.2.1.6.30.20.1 | RowasySapEntry | not-accessible | mandatory | Contains the parameters for a specific Async layer SAP (service access point). |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.1 | ColumnasySapNumber | read-only | mandatory | Indicates the table row containing configuration or monitoring objects for a SAP (service access point) associated with the slot of a card, a port of this card… |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.2 | ColumnasySapRowStatus | read-write | mandatory | Indicates whether or not this specific entry is configured within the MIB. Options: invalid (1): Row is flagged and deleted from the table after the next reset… |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.3 | ColumnasySapAlias | read-write | mandatory | Determines the name which uniquely identifies the SAP (service access point). Range of Values: 1 to 16 alphanumeric characters beginning with an alpha characte… |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.4 | ColumnasySapMCompanionAlias | read-write | mandatory | Determines the name which uniquely identifies the companion MAC SAP (service access point) which will communicate with this SAP. Range of Values: 1 to 16 alpha… |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.5 | ColumnasySapNCompanionAlias | read-write | mandatory | Determines the name which uniquely identifies the X.25 SAP (service access point) which will communicate with this SAP. Range of Values: 1 to 16 alphanumeric c… |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.6 | ColumnasySapX3Profile | read-write | mandatory | Tells the SAP (service access point) which set of X.3 parameters to use. Range of Values: 1 - 255 Default Value: 92 Configuration Changed: Operative |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.7 | ColumnasySapNUI | read-write | mandatory | Defines the Network User ID for this SAP (service access point). Options: 1 to 14 alphanumeric characters Default Value: 0 Configuration Changed: Operative |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.8 | ColumnasySapAddress | read-write | mandatory | Defines the calling address for this SAP (service access point). Range of Values: 1 to 15 digits Default Value: 0 Configuration Changed: Operative |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.9 | ColumnasySapDisconnectRequest | read-write | mandatory | Sends a Disconnect Request to the MAC layer when the YT timer expires. Options: Yes = Enable the disconnect request No = Disable the disconnect request Default… |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.10 | ColumnasySapRxThruputClass | read-write | mandatory | Defines the default receive throughput class that is used at this SAP (service access point). Range of Values: 75 - 64000 bps Default Value: 9600 bps Configura… |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.11 | ColumnasySapTxThruputClass | read-write | mandatory | Defines the default transmit throughput class that is used at this SAP (service access point). Range of Values: 75 to 64000 bps Default Value: 9600 bps Configu… |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.12 | ColumnasySapTxPacketSize | read-write | mandatory | Defines the size of the transmit packet for the Async layer. Range of Values: 16 to 4096 bytes Default Value: 128 bytes Configuration Changed: Operative |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.13 | ColumnasySapRxPacketSize | read-write | mandatory | Defines the size of the receive packet for the Async layer. Range of Values: 16 to 4096 bytes Default Value: 128 bytes Configuration Changed: Operative |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.14 | ColumnasySapTxWindowSize | read-write | mandatory | Defines the size of the transmit window for the Async layer. Range of Values: 1 to 127 Default Value: 2 Configuration Changed: Operative |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.15 | ColumnasySapRxWindowSize | read-write | mandatory | Defines the size of the receive window for the Async layer. Range of Values: 1 to 127 Default Value: 2 Configuration Changed: Operative |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.16 | ColumnasySapYTTimer | read-write | mandatory | Defines the time of inactivity, in seconds, after which the SAP (service access point) will send a disconnect request to the MAC layer. The timer starts when t… |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.17 | ColumnasySapSRTimer | read-write | mandatory | Defines the time of inactivity, in seconds, between command characters. The timer starts when the command mode is entered or when a character of a command is e… |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.18 | ColumnasySapNUILength | read-write | obsolete | Defines the length, in nibbles, allowed for the Network User ID. Range of Values: 1 to 14 Default Value: 0 Configuration Changed: Operative |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.19 | ColumnasySapReverseChargingAcceptance | read-write | mandatory | Authorizes the DCE (Async application) to transmit incoming calls to the DTE (Async user) that requested the reverse charging, if reverse charging acceptance i… |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.20 | ColumnasySapChargingInformation | read-write | mandatory | Authorizes the DCE (Async application) to send charging information to the DTE (user) with the Clear Indication or Clear Confirmation packet. Options: Yes No D… |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.21 | ColumnasySapSubscriptionCUG | read-write | mandatory | Enables the DTE (User) to subscribe to one or more CUGs (Closed User Groups). A CUG permits the DTEs belonging to the group to communicate with each other in t… |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.22 | ColumnasySapSubscriptionCUGOA | read-write | mandatory | Enables the DTE (user) to subscribe to one or more CUGs (Closed User Groups), as in object asySapSubscriptionCUG, with outgoing access. The DTE can originate v… |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.23 | ColumnasySapSubscriptionCUGIA | read-write | mandatory | Enables the DTE (user) to subscribe to one or more CUGs (Closed User Groups), as in object asySapSubscriptionCUG, with incoming access. The DTE can receive inc… |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.24 | ColumnasySapPreferentialCUGIndex | read-write | mandatory | Defines the preferential CUG (Closed User Group) for a DTE (user) with a CUG, CUGOA or CUGIA subscription. Range of Values: 0 to 99 Note: 0 = No preferential C… |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.25 | ColumnasySapReceiptConfirmation | read-write | mandatory | Tells the X.25 layer which receipt confirmation value is required by this SAP (service access point). Options: noAck dBit localAck xmitAck Default Value: noAck… |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.26 | ColumnasySapEnableProtocolId | read-write | mandatory | Controls whether or not the Protocol ID field of the user data is inserted by the Async layer. Options: enable = Allows up to 12 bytes, or 124 bytes for fast s… |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.27 | ColumnasySapProtocolId | read-write | mandatory | Defines the protocol format that is used for incoming call or call request packets to the X.25 call data field. The field consists of 4 hexadecimal octets wher… |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.28 | ColumnasySapPromptSignal | read-write | mandatory | Defines the prompt PAD service signal (banner) that is sent to the MAC layer whenever the Async PAD enters a PAD waiting state or waiting for command state. Op… |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.29 | ColumnasySapAutoConnectDteId | read-write | mandatory | Identifies the remote DTE (by name) to be connected to whenever the async sap receives a Connect Indication or Connect Confirm from the MAC layer. If no name i… |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.30 | ColumnasySapAutoConnectRetry | read-write | mandatory | Defines the number of times this async sap will try to connect (if Connect Accept is not received from the X.25 layer) to the remote DTE defined by the object … |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.31 | ColumnasySapAutoConnectDelayTimer | read-write | mandatory | Defines the time in seconds this async sap will wait before trying to connect to the remote DTE defined by the object asySapAutoConnectDteId whenever the async… |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.32 | ColumnasySapHardwareFlowControl | read-write | mandatory | Enables the MAC to flow control the device via the EIA RTS/CTS signal. Options: Yes No Default Value: No Configuration Changed: Operative |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.33 | ColumnasySapProtocolType | read-write | mandatory | Defines the Async Protocol type for this sap. Options: normal (1) for Normal Async (X.3, X.28, X.29) protocol. iocProtocol (2) for IOC Protocol. ModifiedUDF (3… |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.37 | ColumnasySapControl | write-only | mandatory | Defines the control that is used with the specified Async layer SAP (service access point). Options: clearStats (1): Zeros all the statistic counters for this … |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.40 | ColumnasySapState | read-only | mandatory | Indicates the current state of the Async layer SAP(service access point). Options: disconnected (1) enabled (2) connecting (3) data Transfer (4) resetting (5) … |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.41 | ColumnasySapAsyncFlowControlState | read-only | mandatory | Indicates whether this SAP (service access point) was forced to initiate flow control procedures by the MAC (media access control) layer. Options: flowControlO… |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.42 | ColumnasySapNetworkFlowControlState | read-only | mandatory | Indicates whether or not this SAP (service access point) was forced to initiate flow control procedures by the network layer. Options: flowControlOff (1) flowC… |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.43 | ColumnasySapAsyncTxQueueSize | read-only | mandatory | Indicates the current number of frames to be transmitted to the MAC (media access control) layer. |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.44 | ColumnasySapX25TxQueueSize | read-only | mandatory | Indicates the current number of frames to be send to the network layer. |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.50 | ColumnasySapNumberConnects | read-only | mandatory | Indicates the number of call attempts by this SAP (service access point). |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.51 | ColumnasySapNumberDisconnects | read-only | mandatory | Indicates the number of disconnects for this SAP (service access point). |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.52 | ColumnasySapTxDataCharacters | read-only | mandatory | Indicates the number of data characters that were transmitted from this SAP (service access point) to the MAC layer. |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.53 | ColumnasySapRxDataCharacters | read-only | mandatory | Indicates the number of data characters that were received at this SAP (service access point) from the MAC layer. |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.54 | ColumnasySapParityErrors | read-only | mandatory | Indicates the number of characters with parity errors that were received at this SAP (service access point). |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.55 | ColumnasySapOverruns | read-only | mandatory | Indicates the number of characters with overrun errors that were received at this SAP (service access point). |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.56 | ColumnasySapFlowControlByUser | read-only | mandatory | Indicates the number of flow control characters that were received by this SAP (service access point) from the Async port. |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.57 | ColumnasySapFlowControlByX25 | read-only | mandatory | Indicates the number of flow control messages that were received by this SAP (service access point) from the network layer. |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.58 | ColumnasySapFlowControlToUser | read-only | mandatory | Indicates the number of flow control characters that were transmitted by this SAP (service access point) to the Async port. |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.59 | ColumnasySapFlowControlToX25 | read-only | mandatory | Indicates the number of flow control messages that were sent by this SAP (service access point) to the network layer. |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.60 | ColumnasySapRxReset | read-only | mandatory | Indicates the number of resets that were received at this SAP (service access point) from the network layer. |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.61 | ColumnasySapRxBreak | read-only | mandatory | Indicates the number of breaks that were received at this SAP (service access point). |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.62 | ColumnasySapTxBreak | read-only | mandatory | Indicates the number of breaks that were transmitted from this SAP (service access point). |
| 1.3.6.1.4.1.495.2.1.6.30.20.1.63 | ColumnasySapRxDiscardCharacters | read-only | mandatory | Indicates the number of discard characters that were received at this SAP (service access point). |
| 1.3.6.1.4.1.495.2.1.6.30.21 | TableasyProfTable | not-accessible | mandatory | Contains the X.3 parameters for each defined X.3 profile. |
| 1.3.6.1.4.1.495.2.1.6.30.21.1 | RowasyProfEntry | not-accessible | mandatory | Provides the parameters for a specific X.3 profile SAP (service access point). |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.1 | ColumnasyProfNumber | read-only | mandatory | Identifies the profile SAP (service access point) using a unique numerical value. |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.2 | ColumnasyProfRowStatus | read-write | mandatory | Indicates whether or not this specific entry is configured within the MIB. Options: invalid (1): Row is flagged and deleted from the table after the next reset… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.3 | ColumnasyProfAlias | read-write | mandatory | Identifies the SAP (service access point) using a unique textual name. Range of Values: 1 to 16 alphanumeric characters beginning with an alpha character Defau… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.5 | ColumnasyProfParameter1 | read-write | mandatory | Defines the X.3 parameter 1, PAD recall using a character. This parameter allows the start-stop mode DTE (user) to initiate an escape from the data transfer or… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.6 | ColumnasyProfParameter2 | read-write | mandatory | Defines the X.3 parameter 2, Echo. This parameter provides for characters received from the start-stop mode DTE (user) to be transmitted back to the start-stop… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.7 | ColumnasyProfParameter3 | read-write | mandatory | Defines the X.3 parameter 3, Selection of data forwarding character(s). This parameter allows the selection of defined sets of characters received from the sta… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.8 | ColumnasyProfParameter4 | read-write | mandatory | Defines the X.3 parameter 4, Selection of idle timer delay, in tenths of a second. This parameter allows the selection of the duration of an interval between s… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.9 | ColumnasyProfParameter5 | read-write | mandatory | Defines the X.3 parameter 5, Ancillary device control. This parameter allows for flow control between the PAD and the start-stop mode DTE (user). Options: 0: N… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.10 | ColumnasyProfParameter6 | read-write | mandatory | Defines the X.3 parameter 6, Control of PAD service signals and PAD command signals. This parameter provides the start-stop mode DTE (user) with the ability to… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.11 | ColumnasyProfParameter7 | read-write | mandatory | Defines the X.3 parameter 7, Selection of operation of the PAD on receipt of a break signal from the start-stop mode DTE. This parameter allows the selection o… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.12 | ColumnasyProfParameter8 | read-write | mandatory | Defines the X.3 parameter 8, Discard output. This parameter provides for a PAD to discard the content of user sequences in packets upon request rather than dis… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.13 | ColumnasyProfParameter9 | read-write | mandatory | Defines the X.3 parameter 9, Padding after carriage return (CR). This parameter provides for the automatic insertion of padding characters by the PAD after a c… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.14 | ColumnasyProfParameter10 | read-write | mandatory | Defines the X.3 parameter 10, Line folding. This parameter provides for the automatic insertion of graphic characters by the PAD in the character stream transm… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.15 | ColumnasyProfParameter11 | read-only | mandatory | Defines the X.3 parameter 11, Binary speed of start-stop mode DTE. Options: 0: 110 bit/s 1: 134.5 bit/s 2: 300 bit/s 3: 1200 bit/s 4: 600 bit/s 5: 75 bit/s 6: … |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.16 | ColumnasyProfParameter12 | read-write | mandatory | Defines the X.3 parameter 12, Flow control of the PAD. This parameter allows for flow control between the start-stop mode DTE (user) and the PAD. Options: 0: N… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.17 | ColumnasyProfParameter13 | read-write | mandatory | Defines the X.3 parameter 13, Linefeed insertion after carriage return. This parameter allows for the automatic insertion of a linefeed character in the charac… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.18 | ColumnasyProfParameter14 | read-write | mandatory | Defines the X.3 parameter 14, Padding after linefeed. This parameter provides for the automatic insertion of padding characters in the character stream transmi… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.19 | ColumnasyProfParameter15 | read-write | mandatory | Defines the X.3 parameter 15, Editing. This parameter provides for character size delete, line delete and line display editing capabilities in the PAD command … |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.20 | ColumnasyProfParameter16 | read-write | mandatory | Defines the X.3 parameter 16, Character delete. Range of Values: 0 to 127 0 to126: One character from IA5 127: Character 7/15 (DEL) Default Value: 0 Configurat… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.21 | ColumnasyProfParameter17 | read-write | mandatory | Defines the X.3 parameter 17, Line delete. Range of Values: 0 to 127 0 to 23: One character from the range of IA5 24: Character 1/8 (CAN) 25 to 127: One charac… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.22 | ColumnasyProfParameter18 | read-write | mandatory | Defines the X.3 parameter 18, Line display. Range of Values: 0 to 127 0 to 17: One character from the range of IA5 18: Character 1/8 (DC2) 19 to 127: One chara… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.23 | ColumnasyProfParameter19 | read-write | mandatory | Defines the X.3 parameter 19, Editing PAD service signals. This parameter provides the start-stop mode DTE (user) with the ability to decide whether or not edi… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.24 | ColumnasyProfParameter20 | read-write | mandatory | Defines the X.3 parameter 20, Echo mask. This parameter allows selected defined sets of characters received from the start-stop mode DTE (user) not to be trans… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.25 | ColumnasyProfParameter21 | read-write | mandatory | Defines the X.3 parameter 21, Parity treatment. This parameter allows the PAD to check parity in the data stream from the start-stop mode DTE (user) or generat… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.26 | ColumnasyProfParameter22 | read-write | mandatory | Defines the X.3 parameter 22, Page wait. This parameter allows the PAD to suspend transmission of additional characters to the start-stop mode DTE (user) after… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.27 | ColumnasyProfParameter23 | read-write | mandatory | Defines parameter 23 (extension to X.3), Receive parity type. Options: 0: Parity disable 1: Even parity 2: Odd parity 3: Space parity 4: Mark parity Default Va… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.28 | ColumnasyProfParameter24 | read-write | mandatory | Defines parameter 24 (extension to X.3), Transmit parity type. Options: 0: Parity disable 1: Even parity 2: Odd parity 3: Space parity 4: Mark parity Default V… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.29 | ColumnasyProfParameter25 | read-write | mandatory | Defines parameter 25 (extension to X.3), Flow control on character to PAD. Range of Values: 0 to 127 Note: 0 to 18: One character from the range of IA5 19: DC3… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.30 | ColumnasyProfParameter26 | read-write | mandatory | Defines parameter 26 (extension to X.3), Flow control off character to PAD. Range of Values: 0 to 127 0 to 16: One character from the range of IA5 17: DC1 18 t… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.31 | ColumnasyProfParameter27 | read-write | mandatory | Defines parameter 27 (extension to X.3), Flow control on character to ancillary device. Range of Values: 0 to 127 Note: 0 to 18: One character from the range o… |
| 1.3.6.1.4.1.495.2.1.6.30.21.1.32 | ColumnasyProfParameter28 | read-write | mandatory | Defines parameter 28 (extension to X.3), Flow control off character to ancillary device. Range of Values: 0 to 127 0 to 16: One character from the range of IA5… |
| 1.3.6.1.4.1.495.2.1.6.30.22 | TableasySapProfTable | not-accessible | mandatory | Contains the operational X.3 parameters for each async SAP (service access point). |
| 1.3.6.1.4.1.495.2.1.6.30.22.1 | RowasySapProfEntry | not-accessible | mandatory | Provides the operational X.3 parameters for a specific async sap. |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.1 | ColumnasySapProfSapNumber | read-only | mandatory | Identifies the SAP (service access point) using a unique numerical value. |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.5 | ColumnasySapProfParameter1 | read-write | mandatory | Defines the X.3 parameter 1, PAD recall using a character. This parameter allows the start-stop mode DTE (user) to initiate an escape from the data transfer or… |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.6 | ColumnasySapProfParameter2 | read-write | mandatory | Defines the X.3 parameter 2, Echo. This parameter provides for characters received from the start-stop mode DTE (user) to be transmitted back to the start-stop… |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.7 | ColumnasySapProfParameter3 | read-write | mandatory | Defines the X.3 parameter 3, Selection of data forwarding character(s). This parameter allows the selection of defined sets of characters received from the sta… |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.8 | ColumnasySapProfParameter4 | read-write | mandatory | Defines the X.3 parameter 4, Selection of idle timer delay, in tenths of a second. This parameter allows the selection of the duration of an interval between s… |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.9 | ColumnasySapProfParameter5 | read-write | mandatory | Defines the X.3 parameter 5, Ancillary device control. This parameter allows for flow control between the PAD and the start-stop mode DTE (user). Options: 0: N… |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.10 | ColumnasySapProfParameter6 | read-write | mandatory | Defines the X.3 parameter 6, Control of PAD service signals and PAD command signals. This parameter provides the start-stop mode DTE (user) with the ability to… |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.11 | ColumnasySapProfParameter7 | read-write | mandatory | Defines the X.3 parameter 7, Selection of operation of the PAD on receipt of a break signal from the start-stop mode DTE. This parameter allows the selection o… |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.12 | ColumnasySapProfParameter8 | read-write | mandatory | Defines the X.3 parameter 8, Discard output. This parameter provides for a PAD to discard the content of user sequences in packets upon request rather than dis… |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.13 | ColumnasySapProfParameter9 | read-write | mandatory | Defines the X.3 parameter 9, Padding after carriage return (CR). This parameter provides for the automatic insertion of padding characters by the PAD after a c… |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.14 | ColumnasySapProfParameter10 | read-write | mandatory | Defines the X.3 parameter 10, Line folding. This parameter provides for the automatic insertion of graphic characters by the PAD in the character stream transm… |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.15 | ColumnasySapProfParameter11 | read-only | mandatory | Defines the X.3 parameter 11, Binary speed of start-stop mode DTE. Options: 0: 110 bit/s 1: 134.5 bit/s 2: 300 bit/s 3: 1200 bit/s 4: 600 bit/s 5: 75 bit/s 6: … |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.16 | ColumnasySapProfParameter12 | read-write | mandatory | Defines the X.3 parameter 12, Flow control of the PAD. This parameter allows for flow control between the start-stop mode DTE (user) and the PAD. Options: 0: N… |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.17 | ColumnasySapProfParameter13 | read-write | mandatory | Defines the X.3 parameter 13, Linefeed insertion after carriage return. This parameter allows for the automatic insertion of a linefeed character in the charac… |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.18 | ColumnasySapProfParameter14 | read-write | mandatory | Defines the X.3 parameter 14, Padding after linefeed. This parameter provides for the automatic insertion of padding characters in the character stream transmi… |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.19 | ColumnasySapProfParameter15 | read-write | mandatory | Defines the X.3 parameter 15, Editing. This parameter provides for character size delete, line delete and line display editing capabilities in the PAD command … |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.20 | ColumnasySapProfParameter16 | read-write | mandatory | Defines the X.3 parameter 16, Character delete. Range of Values: 0 to 127 0 to126: One character from IA5 127: Character 7/15 (DEL) Default Value: 0 Configurat… |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.21 | ColumnasySapProfParameter17 | read-write | mandatory | Defines the X.3 parameter 17, Line delete. Range of Values: 0 to 127 0 to 23: One character from the range of IA5 24: Character 1/8 (CAN) 25 to 127: One charac… |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.22 | ColumnasySapProfParameter18 | read-write | mandatory | Defines the X.3 parameter 18, Line display. Range of Values: 0 to 127 0 to 17: One character from the range of IA5 18: Character 1/8 (DC2) 19 to 127: One chara… |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.23 | ColumnasySapProfParameter19 | read-write | mandatory | Defines the X.3 parameter 19, Editing PAD service signals. This parameter provides the start-stop mode DTE (user) with the ability to decide whether or not edi… |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.24 | ColumnasySapProfParameter20 | read-write | mandatory | Defines the X.3 parameter 20, Echo mask. This parameter allows selected defined sets of characters received from the start-stop mode DTE (user) not to be trans… |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.25 | ColumnasySapProfParameter21 | read-write | mandatory | Defines the X.3 parameter 21, Parity treatment. This parameter allows the PAD to check parity in the data stream from the start-stop mode DTE (user) or generat… |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.26 | ColumnasySapProfParameter22 | read-write | mandatory | Defines the X.3 parameter 22, Page wait. This parameter allows the PAD to suspend transmission of additional characters to the start-stop mode DTE (user) after… |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.27 | ColumnasySapProfParameter23 | read-write | mandatory | Defines parameter 23 (extension to X.3), Receive parity type. Options: 0: Parity disable 1: Even parity 2: Odd parity 3: Space parity 4: Mark parity Default Va… |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.28 | ColumnasySapProfParameter24 | read-write | mandatory | Defines parameter 24 (extension to X.3), Transmit parity type. Options: 0: Parity disable 1: Even parity 2: Odd parity 3: Space parity 4: Mark parity Default V… |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.29 | ColumnasySapProfParameter25 | read-write | mandatory | Defines parameter 25 (extension to X.3), Flow control on character to PAD. Range of Values: 0 to 127 0 to 18: One character from the range of IA5 19: DC3 20 to… |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.30 | ColumnasySapProfParameter26 | read-write | mandatory | Defines parameter 26 (extension to X.3), Flow control off character to PAD. Range of Values: 0 to 127 0 to 16: One character from the range of IA5 17 = DC1 18 … |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.31 | ColumnasySapProfParameter27 | read-write | mandatory | Defines parameter 27 (extension to X.3), Flow control on character to ancillary device. Range of Values: 0 to 127 Note: 0 to 18: One character from the range o… |
| 1.3.6.1.4.1.495.2.1.6.30.22.1.32 | ColumnasySapProfParameter28 | read-write | mandatory | Defines parameter 28 (extension to X.3), Flow control off character to ancillary device. Range of Values: 0 to 127 0 to 16: One character from the range of IA5… |
| 1.3.6.1.4.1.495.2.1.6.30.23 | TableasyDteTable | not-accessible | mandatory | A table containing the DTE X.28 Selection command objects for each defined 'abbreviated address'. |
| 1.3.6.1.4.1.495.2.1.6.30.23.1 | RowasyDteEntry | not-accessible | mandatory | The objects for a specific DTE X.28 Selection entry. |
| 1.3.6.1.4.1.495.2.1.6.30.23.1.1 | ColumnasyDteNumber | read-only | mandatory | Identifies the DTE X.28 Selection entry by a unique numerical value. |
| 1.3.6.1.4.1.495.2.1.6.30.23.1.2 | ColumnasyDteRowStatus | read-write | mandatory | Indicates whether this specific entry is configured within the MIB. Entries (rows) may be created by setting this object value to 'valid', or deleted by changi… |
| 1.3.6.1.4.1.495.2.1.6.30.23.1.3 | ColumnasyDteAlias | read-write | mandatory | Identifies the DTE entry by a textual name. Names are unique per service access point. Note: Dte alias (name) must be preceded by a '.' (period) when used in a… |
| 1.3.6.1.4.1.495.2.1.6.30.23.1.5 | ColumnasyDteCalledAddress | read-write | mandatory | Defines the network address of a remote device for this DTE entry. Allowable values: 1 to 15 numerical digits. |
| 1.3.6.1.4.1.495.2.1.6.30.23.1.6 | ColumnasyDteFacilityField | read-write | mandatory | Defines the facility codes and parameters requires for the X.28 Selection command for this DTE entry. The facility codes and parameters must be entered as defi… |
| 1.3.6.1.4.1.495.2.1.6.30.23.1.7 | ColumnasyDteUserDataField | read-write | mandatory | Defines the user data field of the X.28 Selection command for this DTE entry. A value of nul string (blank) means no user data. |
| 1.3.6.1.4.1.495.2.1.6.30.23.1.8 | ColumnasyDteX3Profile | read-write | mandatory | Defines the X.3 Profile number for a specific set of X.3 parameters. The Async layer will initialize its SAP to this X.3 Profile before establishing a logical … |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| DteIndex | INTEGER (1..255) | ||
| PacketSize | INTEGER { bytes16 (4), bytes32 (5), bytes64 (6), bytes128 (7), bytes256 (8), bytes512 (9), bytes1024 (10), bytes2048 (11), bytes4096 (12) } | ||
| ProfIndex | INTEGER (1..255) | ||
| YesNo | INTEGER { no (1), yes (2) } |