DECHUB90-MIB
217 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | Counter enterprises Gauge IpAddress TimeTicks |
| RFC1213-MIB | -- ifIndex DisplayString ifOperStatus -- |
| RFC1316-MIB | -- charPortIndex charPortOperStatus -- |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 0.0 | Scalardh90SlotPrimarySpecific | read-only | mandatory | |
| 0.0 | Scalardh90SlotSecondarySpecific | read-only | mandatory | |
| 0.0 | NodenullSpecific | |||
| 1.3.6.1.4.1.36 | Nodedec | |||
| 1.3.6.1.4.1.36.2 | Nodeema | |||
| 1.3.6.1.4.1.36.2.15 | NodeemaSystem | |||
| 1.3.6.1.4.1.36.2.15.10 | NodeproxyAgent | |||
| 1.3.6.1.4.1.36.2.15.10.1 | Nodedecagent90 | |||
| 1.3.6.1.4.1.36.2.15.10.1.1 | Nodedecagent90v1 | |||
| 1.3.6.1.4.1.36.2.15.10.1.1.1 | NodeconsolePasswordFailure | There have been three consecutive failures to enter a correct password when attempting to log into the DECagent 90 console port. | ||
| 1.3.6.1.4.1.36.2.15.10.1.1.2 | NodenonVolatileRamError | An error in the non-volatile storage on the DECagent 90 has occurred. Some configuration information may have been lost. | ||
| 1.3.6.1.4.1.36.2.15.10.1.1.3 | NodeconfigurationExceeded | An attempt was made to exceed the maximum configuration supported by the DECagent 90. The request to create the additional community or to add the additional m… | ||
| 1.3.6.1.4.1.36.2.15.10.1.1.4 | NodepopulationChange | A module has been added or discovered, or has been deleted or undiscovered. The objects dh90PopulationChange and dh90PopulationLastChange have been updated to … | ||
| 1.3.6.1.4.1.36.2.15.10.1.1.5 | NodemoduleStatusChange | A module has become reachable or unreachable. The objects dh90StatusChange and dh90StatusLastChange have been updated to reflect this change. The community ind… | ||
| 1.3.6.1.4.1.36.2.15.10.1.1.6 | NoderptrPortStatusChange | The port status has changed on a repeater module. The objects dh90StatusChange and dh90StatusLastChange have been updated to reflect this change. The community… | ||
| 1.3.6.1.4.1.36.2.15.10.1.1.7 | NodesrvrPortStatusChange | The port status has changed on a terminal server module. The objects dh90StatusChange and dh90StatusLastChange have been updated to reflect this change. The co… | ||
| 1.3.6.1.4.1.36.2.15.10.1.1.8 | NodebrdgPortStatusChange | The port status has changed on a bridge module. The objects dh90StatusChange and dh90StatusLastChange have been updated to reflect this change. The community i… | ||
| 1.3.6.1.4.1.36.2.18 | NodedecMIBextension | |||
| 1.3.6.1.4.1.36.2.18.10 | Nodedechub90 | |||
| 1.3.6.1.4.1.36.2.18.10.1 | Nodedh90 | |||
| 1.3.6.1.4.1.36.2.18.10.1.1 | Scalardh90Type | read-write | mandatory | Identifies the type of community (hub, string or standalone device) managed by DECagent 90 modules. Setting this variable to invalid(2) deletes the community a… |
| 1.3.6.1.4.1.36.2.18.10.1.2 | Scalardh90Backplane | read-only | mandatory | Media on the backplane of hub. |
| 1.3.6.1.4.1.36.2.18.10.1.3 | Scalardh90LastChange | read-only | mandatory | The value of the sysUpTime at the time a module was added or removed from this community. |
| 1.3.6.1.4.1.36.2.18.10.1.4 | Scalardh90NumberSlots | read-write | mandatory | Number of slots in the hub backplane. Setting this variable to the value 1, 8 or 16 defines the size of a hub in a particular community. Note that attempting t… |
| 1.3.6.1.4.1.36.2.18.10.1.5 | Tabledh90SlotTable | not-accessible | mandatory | A list of modules installed in the DEChub 90. To create a new row (module) in the slot table, set an instance (slot) of dh90SlotModuleType which is currently e… |
| 1.3.6.1.4.1.36.2.18.10.1.5.1 | Rowdh90SlotEntry | not-accessible | mandatory | Contains objects defining characteristics of modules in the community. |
| 1.3.6.1.4.1.36.2.18.10.1.5.1.1 | Columndh90SlotIndex | read-write | mandatory | The slot number containing the module. Setting this variable to the slot number of an empty slot in the community will result in the module being moved to that… |
| 1.3.6.1.4.1.36.2.18.10.1.5.1.2 | Columndh90SlotModuleType | read-write | mandatory | - do not use, provided for backwards compatibility only - Use dh90SlotObjectID instead. The type of the module in a slot. If the slot is known to be empty, a v… |
| 1.3.6.1.4.1.36.2.18.10.1.5.1.3 | Columndh90SlotModuleName | read-write | mandatory | A textual description of the module. Setting a value with embedded spaces or tabs will result in a 'badValue' response. Note that for a DECserver 90, you canno… |
| 1.3.6.1.4.1.36.2.18.10.1.5.1.4 | Columndh90SlotModuleVersion | read-only | mandatory | A textual description of the version level of the hardware and firmware of the module. |
| 1.3.6.1.4.1.36.2.18.10.1.5.1.5 | Columndh90SlotCounterTime | read-only | mandatory | Time since the counters of this module were zeroed. Devices which do not support MOP counters will return a 'noSuchName' response. |
| 1.3.6.1.4.1.36.2.18.10.1.5.1.6 | Columndh90SlotIfBase | read-only | mandatory | An index into the ifTable for the first network interface on this module. Add one to this value to reference the ifTable entry which corresponds to the second … |
| 1.3.6.1.4.1.36.2.18.10.1.5.1.7 | Columndh90SlotIfNumber | read-only | mandatory | The number of network interfaces on this module. For example, a DECbridge 90 has 2 network interfaces, the backbone and the workgroup ports. A DECserver 90L ha… |
| 1.3.6.1.4.1.36.2.18.10.1.5.1.8 | Columndh90SlotPhysicalAddress | read-write | mandatory | A read-write variable for the physical address to allow devices to be added to the hub remotely. Writing this variable as part of a remote add device routine w… |
| 1.3.6.1.4.1.36.2.18.10.1.5.1.9 | Columndh90SlotNumberOfPorts | read-only | mandatory | The number of ports on this module. Returns the following values for the indicated devices: Device Value ================ ===== DECagent 90 1 DECbridge 90 2 DE… |
| 1.3.6.1.4.1.36.2.18.10.1.5.1.10 | Columndh90SlotPassword | read-write | mandatory | Password used to enable privileged operations on devices which support the MOP and RBMS protocols for remote management. Setting a value containing embedded sp… |
| 1.3.6.1.4.1.36.2.18.10.1.5.1.11 | Columndh90SlotNewPassword | read-write | mandatory | Setting this variable causes the agent to set a new password on the device using the value provided as the new password and the current value of dh90SlotPasswo… |
| 1.3.6.1.4.1.36.2.18.10.1.5.1.12 | Columndh90SlotPolling | read-write | mandatory | The current polling status of the module. If the DECagent 90 is polling this device, a get of this variable will return on(2), otherwise off(1) is returned. Se… |
| 1.3.6.1.4.1.36.2.18.10.1.5.1.15 | Columndh90SlotIpAddress | read-write | mandatory | The IP address of the device in the given slot. This value is returned only for devices which implement their own on-board SNMP agent. |
| 1.3.6.1.4.1.36.2.18.10.1.5.1.16 | Columndh90SlotCommunityString | read-write | mandatory | The community string of the device in the given slot. This value is returned only for devices which implement their own on-board SNMP agent. For the managing a… |
| 1.3.6.1.4.1.36.2.18.10.1.5.1.17 | Columndh90SlotObjectID | read-write | mandatory | The sysObjectID of the module in the given slot. This value is provided by the DECagent 90 for modules in community 1. It can be stored manually for modules in… |
| 1.3.6.1.4.1.36.2.18.10.1.5.1.18 | Columndh90SlotProxyStatus | read-only | mandatory | The state of the module as known by the proxy agent. The possible states and their meanings are: reachable - indicates an operational module for which this age… |
| 1.3.6.1.4.1.36.2.18.10.1.5.1.19 | Columndh90SlotConflictStatus | read-only | mandatory | Indicates whether a module conflict has been detected. A conflict indicates that the agent has discovered a module in this slot which is a different type from … |
| 1.3.6.1.4.1.36.2.18.10.1.5.1.20 | Columndh90SlotConflictDiscoveredID | read-only | mandatory | If dh90SlotConflictStatus has a value of conflict(2) then this object indicates the sysObjectID of the module that has been discovered thus creating the confli… |
| 1.3.6.1.4.1.36.2.18.10.1.5.1.21 | Columndh90SlotReset | read-write | mandatory | A control variable to perform reset functions on DEChub 90 modules which are in the same hub as the managing agent. The agent must be the hub master (see da90B… |
| 1.3.6.1.4.1.36.2.18.10.1.6 | Tabledh90TrapAddressTable | not-accessible | mandatory | A table of IP addresses to which this device will send SNMP traps. |
| 1.3.6.1.4.1.36.2.18.10.1.6.1 | Rowdh90TrapEntry | not-accessible | mandatory | Each entry contains an IP address to which all SNMP traps will be sent by this community. |
| 1.3.6.1.4.1.36.2.18.10.1.6.1.1 | Columndh90TrapAddress | read-write | mandatory | An IP address to which all SNMP traps generated for this community will be sent. Setting an instance to a value of zero will delete the row in the table. Setti… |
| 1.3.6.1.4.1.36.2.18.10.1.7 | Scalardh90LastErrorMsg | read-only | mandatory | Indicates the last error message for this community. Examples of errors which may cause this string to be updated are: - An error in a proxy operation (get or … |
| 1.3.6.1.4.1.36.2.18.10.1.8 | Scalardh90LastErrorChange | read-only | mandatory | The value of MIB-II's sysUpTime (in the agent supporting this MIB) when a module event occurred which caused the dh90LastErrorMsg object to be updated. |
| 1.3.6.1.4.1.36.2.18.10.1.9 | Scalardh90LastErrorSlot | read-only | mandatory | The slot of the module which caused the dh90LastErrorMsg object to be updated. A value of zero (0) indicates that an error has not yet occurred. |
| 1.3.6.1.4.1.36.2.18.10.1.10 | Scalardh90PopulationChange | read-only | mandatory | The total number of changes in population of the modules within the community. This counter is incremented: - when a module is added or discovered, or - when a… |
| 1.3.6.1.4.1.36.2.18.10.1.11 | Scalardh90PopulationLastChange | read-only | mandatory | The value of MIB-II's sysUpTime (in the agent supporting this MIB) when a module event occurred which caused the increment of the dh90PopulationChange counter. |
| 1.3.6.1.4.1.36.2.18.10.1.12 | Scalardh90StatusChange | read-only | mandatory | The total number of changes to status of the modules within the community. This counter is incremented: - when a proxied module becomes reachable, or - when a … |
| 1.3.6.1.4.1.36.2.18.10.1.13 | Scalardh90StatusLastChange | read-only | mandatory | The value of MIB-II's sysUpTime (in the agent supporting this MIB) when a module event occurred which caused the increment of the dh90StatusChange counter. |
| 1.3.6.1.4.1.36.2.18.10.2 | Nodeda90 | |||
| 1.3.6.1.4.1.36.2.18.10.2.1 | Scalarda90FlashErasures | read-only | mandatory | The number of times the flash memory on this DECagent 90 has been erased. This number is the total of erasures for all flash segments. |
| 1.3.6.1.4.1.36.2.18.10.2.2 | Scalarda90Maintenance | read-write | mandatory | A control variable to perform reset functions on a DECagent 90. In response to a Get or a getNext request, the agent returns ready(1) if SNMP sets are enabled,… |
| 1.3.6.1.4.1.36.2.18.10.2.3 | Scalarda90CommunityNumber | read-only | mandatory | Number of entries in the da90CommunityTable. |
| 1.3.6.1.4.1.36.2.18.10.2.4 | Tableda90CommunityTable | not-accessible | mandatory | A table of community strings for client communities. |
| 1.3.6.1.4.1.36.2.18.10.2.4.1 | Rowda90CommunityEntry | not-accessible | mandatory | Contains community type and strings, including the read-only profile, the read-write profile and a trap string. |
| 1.3.6.1.4.1.36.2.18.10.2.4.1.1 | Columnda90CommunityIndex | read-only | mandatory | Index into hub-community string pair table, identifies the community being accessed. |
| 1.3.6.1.4.1.36.2.18.10.2.4.1.2 | Columnda90CommunityType | read-write | mandatory | Identifies whether the current community information is active for this row in the community table. The value unknown(1) is read-only and indicates that this r… |
| 1.3.6.1.4.1.36.2.18.10.2.4.1.3 | Columnda90CommunityROString | read-write | mandatory | Community string, with a read-only profile, used to access a client hub. All community strings in the read-only set must be unique. Setting such a community st… |
| 1.3.6.1.4.1.36.2.18.10.2.4.1.4 | Columnda90CommunityRWString | read-write | mandatory | Community string, with a read-write profile, used to access a client hub. All community strings in the read-write set must be unique. Setting such a community … |
| 1.3.6.1.4.1.36.2.18.10.2.4.1.5 | Columnda90CommunityTrapString | read-write | mandatory | Community string sent with traps generated due to events caused by this community. The trap community strings do not have to be unique. This variable is read u… |
| 1.3.6.1.4.1.36.2.18.10.2.5 | Scalarda90AgentSlot | read-only | mandatory | The slot number in which the managing DECagent 90 resides. |
| 1.3.6.1.4.1.36.2.18.10.2.6 | Tableda90ErrorlogTable | not-accessible | mandatory | The da90ErrorlogTable is a ring of eight (8) errorlog entries for this DECagent 90. Thus, the ninth entry will overwrite the first entry, the tenth entry will … |
| 1.3.6.1.4.1.36.2.18.10.2.6.1 | Rowda90ErrorlogEntry | not-accessible | mandatory | An entry in the errorlog containing the DECagent reset count at the time the entry was logged, the timestamp in hundredths of a second since the last reset occ… |
| 1.3.6.1.4.1.36.2.18.10.2.6.1.1 | Columnda90ErrorlogIndex | read-only | mandatory | The index into the errorlog table. |
| 1.3.6.1.4.1.36.2.18.10.2.6.1.2 | Columnda90ErrorlogResetCount | read-only | mandatory | The number of times the DECagent has been reset (soft or hard reset) since the creation of the errorlog or the last reset-to-factory settings. A value of zero … |
| 1.3.6.1.4.1.36.2.18.10.2.6.1.3 | Columnda90ErrorlogTimeStamp | read-only | mandatory | The uptime, in hundredths of a second, of the DECagent when this entry was logged. |
| 1.3.6.1.4.1.36.2.18.10.2.6.1.4 | Columnda90ErrorlogWriteCount | read-only | mandatory | The number of times this row in the errorlog table has been written. |
| 1.3.6.1.4.1.36.2.18.10.2.6.1.5 | Columnda90ErrorlogData | read-only | mandatory | A textual description of the error for this errorlog entry. |
| 1.3.6.1.4.1.36.2.18.10.2.7 | Scalarda90ResetCount | read-only | mandatory | The total number of resets to the agent that has occurred, including power-ups. This counter is maintained in non-volatile storage and is reset to zero only wh… |
| 1.3.6.1.4.1.36.2.18.10.2.8 | Scalarda90BackplaneMode | read-write | mandatory | The desired state of the DECagent 90's hub mastership (i.e. it's ability to directly manage repeaters, terminal servers and bridges and discover other modules … |
| 1.3.6.1.4.1.36.2.18.10.2.9 | Scalarda90BackplaneState | read-only | mandatory | Indicates whether the DECagent 90 is managing the hub (i.e. capable of directly managing repeaters, terminal servers and bridges and discovering other modules). |
| 1.3.6.1.4.1.36.2.18.10.2.10 | Scalarda90BackplaneAddrDbAgingTime | read-write | mandatory | A non-volatile value indicating the number of minutes an address discovered by the agent will remain in the forwarding database address table. This variable is… |
| 1.3.6.1.4.1.36.2.18.10.2.11 | Scalarda90LoadAdminStatus | read-write | mandatory | This object is used to control the program TFTP load process of a device. When read, the value other(1) is returned. When set to start-read(2) the device initi… |
| 1.3.6.1.4.1.36.2.18.10.2.12 | Scalarda90LoadOperStatus | read-only | mandatory | The final state of the last load attempt. The value none(1) indicates that no load has been attempted, ever. This object is non-volatile. It's default value is… |
| 1.3.6.1.4.1.36.2.18.10.2.13 | Scalarda90LoadFilename | read-write | mandatory | The name of the file in which to load. When the device is reading, this is the name of the file to be read. When the device is being written, this is the only … |
| 1.3.6.1.4.1.36.2.18.10.2.14 | Scalarda90LoadIpHostAddr | read-write | mandatory | The IP address of the host from which to load. When the device is reading, this is the IP address of the host in which the read will be directed. When the devi… |
| 1.3.6.1.4.1.36.2.18.10.2.15 | Scalarda90LoadDevSpecific | read-only | mandatory | A device specific parameter which is used to indicate detailed error information about the last attempted load. A value of none(0) indicates that no load has b… |
| 1.3.6.1.4.1.36.2.18.10.2.16 | Scalarda90SetupPortStatus | read-write | mandatory | This object indicates the current status of the setup port on the front panel of the DECagent. When read, it will return either console(1) or slip(2). Writing … |
| 1.3.6.1.4.1.36.2.18.10.3 | Nodeds90L | |||
| 1.3.6.1.4.1.36.2.18.10.3.1 | Scalards90LNumberModules | read-only | mandatory | Number of DECserver 90 modules represented in the ds90LModuleTable. |
| 1.3.6.1.4.1.36.2.18.10.3.2 | Tableds90LModuleTable | not-accessible | mandatory | A table of DECserver 90 modules installed in the group. The number of entries is given by ds90LNumberModules. |
| 1.3.6.1.4.1.36.2.18.10.3.2.1 | Rowds90LModuleEntry | not-accessible | mandatory | Contains objects defining characteristics of DECserver 90 modules in the group. |
| 1.3.6.1.4.1.36.2.18.10.3.2.1.1 | Columnds90LSlotIndex | read-only | mandatory | The slot index value which addresses the dh90SlotTable for this module. |
| 1.3.6.1.4.1.36.2.18.10.3.2.1.2 | Columnds90LDot3StatsDeferredTransmissions | read-only | mandatory | A count of frames for which the first transmission attempt on a particular interface is delayed because the medium is busy. The count represented by an instanc… |
| 1.3.6.1.4.1.36.2.18.10.3.2.1.3 | Columnds90LDot3StatsSingleCollisionFrames | read-only | mandatory | A count of successfully transmitted frames on a particular interface for which transmission is inhibited by exactly one collision. (If the DECserver 90 impleme… |
| 1.3.6.1.4.1.36.2.18.10.3.2.1.4 | Columnds90LDot3StatsMultipleCollisionFrames | read-only | mandatory | A count of successfully transmitted frames on a particular interface for which transmission is inhibited by more than one collision. (If the DECserver 90 imple… |
| 1.3.6.1.4.1.36.2.18.10.3.2.1.5 | Columnds90LEnetDataOverruns | read-only | mandatory | A count of the number of frames arriving at the DECserver 90 that were lost due to data overrun since it last reinitialized or zeroed counters. |
| 1.3.6.1.4.1.36.2.18.10.3.2.1.6 | Columnds90LLatCircMsgsIns | read-only | mandatory | A count of the number of LAT circuit messages received by this DECserver 90 since it last reinitialized or zeroed counters. |
| 1.3.6.1.4.1.36.2.18.10.3.2.1.7 | Columnds90LLatCircMsgsOuts | read-only | mandatory | A count of the number of LAT circuit messages transmitted by this DECserver 90 since it last reinitialized or zeroed counters. |
| 1.3.6.1.4.1.36.2.18.10.3.2.1.8 | Columnds90LLatSessSolicitAccepts | read-only | mandatory | A count of the number of LAT solicits accepted by this DECserver 90 since it last reinitialized or zeroed counters. |
| 1.3.6.1.4.1.36.2.18.10.3.2.1.9 | Columnds90LLatSessSolicitRejects | read-only | mandatory | A count of the number of LAT solicits rejected by this DECserver 90 since it last reinitialized or zeroed counters. |
| 1.3.6.1.4.1.36.2.18.10.3.2.1.10 | Columnds90LLatCircDuplsMsgs | read-only | mandatory | A count of the number of duplicate LAT messages the DECserver 90 LAT implementation has discarded since it last reinitialized or zeroed counters. |
| 1.3.6.1.4.1.36.2.18.10.3.2.1.11 | Columnds90LLatCircMsgRetransmits | read-only | mandatory | A count of the total number of LAT circuit messages this DECserver 90 has retransmitted since it last reinitialized or zeroed counters. |
| 1.3.6.1.4.1.36.2.18.10.3.2.1.12 | Columnds90LLatSessIllegalSlots | read-only | mandatory | A count of the number of illegal LAT slots this DECserver 90 has received on all LAT sessions since it last reinitialized or zeroed counters. |
| 1.3.6.1.4.1.36.2.18.10.3.2.1.13 | Columnds90LIllegalMulticastRcvs | read-only | mandatory | A count of the number of illegal multicast LAT messages received on this DECserver 90 since it last reinitialized or zeroed counters. |
| 1.3.6.1.4.1.36.2.18.10.3.2.1.14 | Columnds90LLatCircKeepAlive | read-only | mandatory | This defines the number of seconds the LAT circuits provider waits between transmitting LAT circuit layer keep-alive messages. Writing to this object is equiva… |
| 1.3.6.1.4.1.36.2.18.10.3.2.1.15 | Columnds90LLatCircRetransmitLimit | read-only | mandatory | This object defines the maximum number of LAT circuit message retransmissions the server will attempt before declaring the circuit failed. Writing to this obje… |
| 1.3.6.1.4.1.36.2.18.10.3.2.1.16 | Columnds90LLatCircInvalidMsgs | read-only | mandatory | This counts the number of invalid LAT messages received on its entry's LAT circuit since the DECserver last reinitialized or zeroed counters. |
| 1.3.6.1.4.1.36.2.18.10.3.2.1.17 | Columnds90LAuthorizeMode | read-write | mandatory | Setting a value of enable(1) causes the DECserver to enter an enable-authorized-mode-pending state. The device will enter authorized mode if the power is cycle… |
| 1.3.6.1.4.1.36.2.18.10.3.2.1.18 | Columnds90LMaintenance | read-write | mandatory | A control variable to reset the counters on a DECserver 90. In response to a Get or a getNext request, the agent always returns ready(1). Setting the value to … |
| 1.3.6.1.4.1.36.2.18.10.3.2.1.19 | Columnds90LPrompt | read-write | mandatory | Contains the prompt displayed when a session is local to the DECserver 90L+ terminal server. The default value is '->'. This variable returns 'noSuchName' for … |
| 1.3.6.1.4.1.36.2.18.10.3.3 | Tableds90LPortTable | not-accessible | mandatory | A table of port specific variables on this DECserver 90. The index for a terminal server port is given by (slot number * 100) + port number The number of ports… |
| 1.3.6.1.4.1.36.2.18.10.3.3.1 | Rowds90LPortEntry | not-accessible | mandatory | A single LAT session instance this DECserver 90 currently provides. |
| 1.3.6.1.4.1.36.2.18.10.3.3.1.1 | Columnds90LPortIndex | read-only | mandatory | The value of charPortIndex for this port. |
| 1.3.6.1.4.1.36.2.18.10.3.3.1.2 | Columnds90LPortRemoteModification | read-write | mandatory | Enables and disables remote modification of the port by the host system. |
| 1.3.6.1.4.1.36.2.18.10.3.3.1.3 | Columnds90LPortType | read-write | mandatory | Selects the type of device connected to the port. |
| 1.3.6.1.4.1.36.2.18.10.3.3.1.4 | Columnds90LPortBreak | read-write | mandatory | Determines if the port responds to local or remote break. |
| 1.3.6.1.4.1.36.2.18.10.3.3.1.5 | Columnds90LPortTest | read-write | mandatory | Setting this variable to enable(2) places the port into loopback mode. Loopback mode can be used to verify that a port is receiving and sending characters. |
| 1.3.6.1.4.1.36.2.18.10.3.3.1.6 | Columnds90LPortAutoConfigure | read-write | mandatory | Enables or disables the autoconfiguration of a port on a DECserver 90L+. Enabling autoconfiguration allows default settings to be restored to a port after each… |
| 1.3.6.1.4.1.36.2.18.10.3.3.1.7 | Columnds90LPortOnDemandLoading | read-write | mandatory | Enables or disables on-demand loading of fonts to a port in a DECserver 90L+. For the DECserver 90L, reads of this variable always return disable(1). Setting t… |
| 1.3.6.1.4.1.36.2.18.10.3.3.1.8 | Columnds90LPortDedicatedServiceStatus | read-only | mandatory | A status variable indicating whether or not dedicated service is enabled on a terminal server port. Dedicated service on a port means that the port will attemp… |
| 1.3.6.1.4.1.36.2.18.10.3.3.1.9 | Columnds90LPortDedicatedServiceName | read-write | mandatory | The name of the dedicated service to which a connection will be attempted when a connection to the terminal server port is made. Setting a valid name, from 1 t… |
| 1.3.6.1.4.1.36.2.18.10.3.3.1.10 | Columnds90LPortDedicatedServiceNode | read-write | mandatory | The node name of the remote system to which a connection will be attempted when a connection to the terminal server port is made. This variable can only be set… |
| 1.3.6.1.4.1.36.2.18.10.3.3.1.11 | Columnds90LPortDedicatedServicePort | read-write | mandatory | The port on the remote system to which a connection will be attempted when a connection to the terminal server port is made. This variable can only be set for … |
| 1.3.6.1.4.1.36.2.18.10.3.3.1.12 | Columnds90LPortPreferredServiceStatus | read-only | mandatory | A status variable indicating whether or not preferred service is enabled on a terminal server port. Preferred service on a port means that the port will attemp… |
| 1.3.6.1.4.1.36.2.18.10.3.3.1.13 | Columnds90LPortPreferredServiceName | read-write | mandatory | The name of the preferred service to which a connection will be attempted when a connection to the terminal server port is made. Setting a valid name, from 1 t… |
| 1.3.6.1.4.1.36.2.18.10.3.3.1.14 | Columnds90LPortPreferredServiceNode | read-write | mandatory | The node name of the remote system to which a connection will be attempted when a connection to the terminal server port is made. This variable can only be set… |
| 1.3.6.1.4.1.36.2.18.10.3.3.1.15 | Columnds90LPortPreferredServicePort | read-write | mandatory | The port on the remote system to which a connection will be attempted when a connection to the terminal server port is made. This variable can only be set for … |
| 1.3.6.1.4.1.36.2.18.10.3.4 | Tableds90LSessionTable | not-accessible | mandatory | The list of all LAT sessions active on this DECserver 90. |
| 1.3.6.1.4.1.36.2.18.10.3.4.1 | Rowds90LSessionEntry | not-accessible | mandatory | A single LAT session instance this DECserver 90 currently provides. |
| 1.3.6.1.4.1.36.2.18.10.3.4.1.1 | Columnds90LSessionPort | read-only | mandatory | The value of charPortIndex for the port to which this session belongs. |
| 1.3.6.1.4.1.36.2.18.10.3.4.1.2 | Columnds90LSessionIndex | read-only | mandatory | The session index in the context of the port, a non-zero positive integer. Will be 1 for the DECserver 90L, 4 for DECserver 90L+. |
| 1.3.6.1.4.1.36.2.18.10.3.4.1.3 | Columnds90LSessionRemoteNode | read-only | mandatory | The name of the remote node providing the service for this session. |
| 1.3.6.1.4.1.36.2.18.10.3.4.1.4 | Columnds90LSessionService | read-only | mandatory | The service to which this session is connected. |
| 1.3.6.1.4.1.36.2.18.10.3.4.1.5 | Columnds90LSessionRemotePortId | read-only | mandatory | The name of the port at the remote node providing the connection, for example, LAT121. |
| 1.3.6.1.4.1.36.2.18.10.4 | Nodedrpt90 | |||
| 1.3.6.1.4.1.36.2.18.10.4.1 | Tabledrpt90PortTable | not-accessible | mandatory | A table of port specific variables on this DECrepeater 90. The index for a repeater port is given by (slot number * 100) + port number The number of ports is g… |
| 1.3.6.1.4.1.36.2.18.10.4.1.1 | Rowdrpt90PortEntry | not-accessible | mandatory | A collection of objects containing information for a given interface. |
| 1.3.6.1.4.1.36.2.18.10.4.1.1.1 | Columndrpt90PortIndex | read-only | mandatory | Identifies the module and port. The value of this object is given by: (slot number * 100) + port number |
| 1.3.6.1.4.1.36.2.18.10.4.1.1.2 | Columndrpt90PortName | read-write | mandatory | The text description of the port given by the network manager. Setting a value containing embedded spaces or tabs will result in a 'badValue' response. |
| 1.3.6.1.4.1.36.2.18.10.4.1.1.3 | Columndrpt90PortAdminStatus | read-write | mandatory | The desired state of the port. |
| 1.3.6.1.4.1.36.2.18.10.4.1.1.4 | Columndrpt90PortState | read-only | mandatory | The state of the port. The value unknown(1) is returned when the port state cannot be determined. The value autoPartitioned(2) indicates that the repeater has … |
| 1.3.6.1.4.1.36.2.18.10.4.1.1.5 | Columndrpt90PortType | read-only | mandatory | The physical medium type of the port. |
| 1.3.6.1.4.1.36.2.18.10.4.1.1.6 | Columndrpt90PortPartitions | read-only | mandatory | The number of times this port has partitioned. This value is significant only if drpt90PortStatus is not unknown(1). |
| 1.3.6.1.4.1.36.2.18.10.4.1.1.7 | Columndrpt90PortAutoPartitionReason | read-only | mandatory | Errors currently detected on the port. |
| 1.3.6.1.4.1.36.2.18.10.4.1.1.8 | Columndrpt90PortJamBits | read-only | mandatory | The number of jam bits being used on the port segment. |
| 1.3.6.1.4.1.36.2.18.10.4.2 | Tabledrpt90PortAddrTable | not-accessible | mandatory | A list of MAC addresses paired with the repeater port on which they have been seen. |
| 1.3.6.1.4.1.36.2.18.10.4.2.1 | Rowdrpt90PortAddrEntry | not-accessible | mandatory | A MAC address and the repeater port on which it resides. |
| 1.3.6.1.4.1.36.2.18.10.4.2.1.1 | Columndrpt90PortPhyAddr | read-only | mandatory | A MAC address seen on this port. |
| 1.3.6.1.4.1.36.2.18.10.4.2.1.2 | Columndrpt90PortAddrIndex | read-only | mandatory | Identifies the module and port. The value of this object is the same as drpt90PortIndex and is given by: (slot number * 100) + port number |
| 1.3.6.1.4.1.36.2.18.10.5 | Nodedb90ext | |||
| 1.3.6.1.4.1.36.2.18.10.5.1 | Nodedb90system | |||
| 1.3.6.1.4.1.36.2.18.10.5.1.1 | NodedbSysChar | |||
| 1.3.6.1.4.1.36.2.18.10.5.1.1.1 | ScalardbSysRomVersion | read-only | mandatory | The version number of the software stored in ROM. The return value is encoded as (major_version*10 + minor version). For example, version 1.0 is returned as 10… |
| 1.3.6.1.4.1.36.2.18.10.5.1.1.2 | ScalardbSysInitSwitch | read-write | mandatory | This object allows the management action of initializing a device and forcing it to run selftest. It can also be used to reset all information added to the dev… |
| 1.3.6.1.4.1.36.2.18.10.5.1.2 | NodedbSysStatus | |||
| 1.3.6.1.4.1.36.2.18.10.5.1.2.1 | ScalardbSysDeviceState | read-only | mandatory | The operational state of the device. |
| 1.3.6.1.4.1.36.2.18.10.5.1.2.2 | ScalardbSysNvramFailed | read-only | mandatory | A flag that, when set to true(1), indicates that the NVRAM failed selftest following the last initialization of the device. Values set to variables maintained … |
| 1.3.6.1.4.1.36.2.18.10.5.2 | Nodedb90interfaces | |||
| 1.3.6.1.4.1.36.2.18.10.5.2.1 | TabledbIfTable | not-accessible | mandatory | A list of interface entries. The number of entries is given by ifNumber. |
| 1.3.6.1.4.1.36.2.18.10.5.2.1.1 | RowdbIfEntry | not-accessible | mandatory | A collection of objects containing information for a given interface. |
| 1.3.6.1.4.1.36.2.18.10.5.2.1.1.1 | ColumndbIfIndex | read-only | mandatory | Identifies the interface. The value of this object is the same as the ifIndex for this interface. |
| 1.3.6.1.4.1.36.2.18.10.5.2.1.1.2 | ColumndbIfReceiveBadFrames | read-only | mandatory | Number of frames received with a bad frame check sequence or the device received a frame loss indication from the hardware on the interface. |
| 1.3.6.1.4.1.36.2.18.10.5.2.1.1.3 | ColumndbIfTransmitErrorFrames | read-only | mandatory | Number of frames that were transmitted with an error on the line. |
| 1.3.6.1.4.1.36.2.18.10.5.3 | Nodedb90bridge | |||
| 1.3.6.1.4.1.36.2.18.10.5.3.1 | Nodedb90Char | |||
| 1.3.6.1.4.1.36.2.18.10.5.3.1.1 | Scalardb90LB100SpanningTreeVer | read-only | mandatory | The version number of the Spanning Tree algorithm used by the bridge when in the LAN Bridge 100 Spanning Tree mode. |
| 1.3.6.1.4.1.36.2.18.10.5.3.1.2 | Scalardb90802SpanningTreeVer | read-only | mandatory | The version number of the Spanning Tree algorithm used by the bridge when in the 802.1d Spanning Tree mode. |
| 1.3.6.1.4.1.36.2.18.10.5.3.1.3 | Scalardb90MaxForwardingDBEntries | read-only | mandatory | The maximum number of address entries that the bridge can store in its volatile memory. |
| 1.3.6.1.4.1.36.2.18.10.5.3.1.4 | Scalardb90MaxNVForwardingDBEntries | read-only | mandatory | The maximum number of permanent address entries that the bridge can store in its NVRAM. |
| 1.3.6.1.4.1.36.2.18.10.5.3.1.5 | Scalardb90MaxProtocolDBEntries | read-only | mandatory | The maximum number of protocol entries that the bridge can store in its protocol database. These entries control the handling of frames based on their Ethernet… |
| 1.3.6.1.4.1.36.2.18.10.5.3.1.6 | Scalardb90MaxNVProtocolDBEntries | read-only | mandatory | The maximum number of protocol entries that the bridge can store in its NVRAM. These are retained after a power-down. |
| 1.3.6.1.4.1.36.2.18.10.5.3.2 | Nodedb90Stat | |||
| 1.3.6.1.4.1.36.2.18.10.5.3.2.1 | Scalardb90CurrProtocolDBEntries | read-only | mandatory | The number of protocol entries that are stored in the bridge's protocol database. These control the handling of frames based on their Ethernet protocol type, I… |
| 1.3.6.1.4.1.36.2.18.10.5.3.2.2 | Scalardb90CurrNVProtocolDBEntries | read-only | mandatory | The number of protocol entries in the bridge's NVRAM. These are retained after a power loss. |
| 1.3.6.1.4.1.36.2.18.10.5.3.2.3 | Scalardb90MgmtHeardPort | read-only | mandatory | The port on which this command was received. |
| 1.3.6.1.4.1.36.2.18.10.5.3.2.4 | Scalardb90LB100BeingPolled | read-only | mandatory | The address of the LAN Bridge 100 mode bridge that sent this bridge into the LAN Bridge 100 Spanning Tree mode. If this bridge is the Root, this object indicat… |
| 1.3.6.1.4.1.36.2.18.10.5.3.2.5 | Scalardb90TimeSinceLastHello | read-only | mandatory | The number of seconds since the bridge last sent a hello message. |
| 1.3.6.1.4.1.36.2.18.10.5.3.2.6 | Scalardb90HubManagement | read-write | mandatory | Indicates whether the bridge is managing the hub (i.e., is capable of managing repeaters inserted in the hub). |
| 1.3.6.1.4.1.36.2.18.10.5.3.2.7 | Scalardb90CurrFdbEntries | read-only | mandatory | The number of entries currently active in the DECbridge 90 forwarding database, or one more than the value of db90MaxForwardingDBEntries if the bridge has exce… |
| 1.3.6.1.4.1.36.2.18.10.5.3.3 | Nodedb90Coun | |||
| 1.3.6.1.4.1.36.2.18.10.5.3.3.1 | Scalardb90SpanningTreeModeChanges | read-only | mandatory | The number of times that the bridge switched from the 802.1d Spanning Tree mode to the LB100 Spanning Tree mode. |
| 1.3.6.1.4.1.36.2.18.10.5.3.4 | Nodedb90Span | |||
| 1.3.6.1.4.1.36.2.18.10.5.3.4.1 | Scalardb90BestRootAge | read-only | mandatory | The age, in hundredths of seconds, of the hello message that established the best root. |
| 1.3.6.1.4.1.36.2.18.10.5.3.4.2 | Scalardb90TopologyChangeFlag | read-only | mandatory | A flag that indicates whether a topology change is currently in effect on the extended LAN. |
| 1.3.6.1.4.1.36.2.18.10.5.3.4.3 | Scalardb90TellParentFlag | read-only | mandatory | A flag that indicates if the bridge is attempting to propagate a topology change towards the root. |
| 1.3.6.1.4.1.36.2.18.10.5.3.4.4 | Scalardb90ForwardingDBShortAgingTime | read-only | mandatory | The number of seconds that the bridge keeps learned entries active while a topology change is in effect. |
| 1.3.6.1.4.1.36.2.18.10.5.3.4.5 | Scalardb90BadHelloLimit | read-only | mandatory | The number of hello intervals during which the bridge receives one or more bad hellos on a line, before the bridge performs a test on the link. A bad hello mes… |
| 1.3.6.1.4.1.36.2.18.10.5.3.4.6 | Scalardb90BadHelloResetTimer | read-write | mandatory | The number of hello intervals without bad hellos that the bridge will wait before it resets its bad hello count to zero. |
| 1.3.6.1.4.1.36.2.18.10.5.3.4.7 | Scalardb90NoFrameInterval | read-only | mandatory | The number of seconds of inactivity on a line that will cause the bridge to run a test on that line. The bridge considers a line to be inactive if it does not … |
| 1.3.6.1.4.1.36.2.18.10.5.3.4.8 | Scalardb90LB100PollTime | read-only | mandatory | The number of seconds that a root bridge in LAN Bridge 100 mode waits between polling the LAN Bridge 100 that is keeping it in this mode. This polling is done … |
| 1.3.6.1.4.1.36.2.18.10.5.3.4.9 | Scalardb90LB100ResponseTimeout | read-only | mandatory | The number of seconds that a Root in LAN Bridge 100 Spanning Tree mode will wait for a response from the LAN Bridge 100 which is keeping it in this mode, befor… |
| 1.3.6.1.4.1.36.2.18.10.5.3.4.10 | Scalardb90LB100SpanningTreeCompat | read-only | mandatory | A switch that controls the Spanning Tree mode used by the bridge. If in Auto-Select mode, the bridge will go into 802 Spanning Tree mode by default, but will s… |
| 1.3.6.1.4.1.36.2.18.10.5.3.5 | Nodedb90PortInterfaces | |||
| 1.3.6.1.4.1.36.2.18.10.5.3.5.1 | Tabledb90IfTable | not-accessible | mandatory | A list of interface entries. The number of entries is given by ifNumber. |
| 1.3.6.1.4.1.36.2.18.10.5.3.5.1.1 | Rowdb90IfEntry | not-accessible | mandatory | A collection of objects containing information for a given interface. |
| 1.3.6.1.4.1.36.2.18.10.5.3.5.1.1.1 | Columndb90IfIndex | read-only | mandatory | Identifies the interface. The value of this object is the same as the ifIndex for this interface. |
| 1.3.6.1.4.1.36.2.18.10.5.3.5.1.1.2 | Columndb90IfReceiveDeviceFrames | read-only | mandatory | The number of frames addressed to the bridge itself that were received on this line. |
| 1.3.6.1.4.1.36.2.18.10.5.3.5.1.1.3 | Columndb90IfExceededBadHelloLimits | read-only | mandatory | The number of times that the bad hellos on the line exceeded the bad hello limit. |
| 1.3.6.1.4.1.36.2.18.10.5.3.5.2 | Tabledb90IfEtherTable | not-accessible | mandatory | A list of interface entries for an Ethernet port. |
| 1.3.6.1.4.1.36.2.18.10.5.3.5.2.1 | Rowdb90IfEtherEntry | not-accessible | mandatory | A collection of objects containing information for a given interface. |
| 1.3.6.1.4.1.36.2.18.10.5.3.5.2.1.1 | Columndb90IfEthIndex | read-only | mandatory | Identifies the interface. The value of this object is the same as the ifIndex for this interface. |
| 1.3.6.1.4.1.36.2.18.10.5.3.5.2.1.2 | Columndb90IfEthFramingErrors | read-only | mandatory | The number of times that a frame received on the line contained both a non-integer multiple of eight bits and a CRC error. |
| 1.3.6.1.4.1.36.2.18.10.5.3.5.2.1.3 | Columndb90IfEthCarrierLosses | read-only | mandatory | The number of times that the bridge detected a loss of the carrier signal while transmitting a frame on the line. |
| 1.3.6.1.4.1.36.2.18.10.5.3.5.2.1.4 | Columndb90IfEthExceededCollisionLimits | read-only | mandatory | The number of times that the bridge failed to transmit a frame on this line after 16 attempts, the collision limit. |
| 1.3.6.1.4.1.36.2.18.10.5.3.5.3 | Tabledb90IfSpanTable | not-accessible | mandatory | A list of interface entries for a port. |
| 1.3.6.1.4.1.36.2.18.10.5.3.5.3.1 | Rowdb90IfSpanEntry | not-accessible | mandatory | A collection of objects containing information for a given interface. |
| 1.3.6.1.4.1.36.2.18.10.5.3.5.3.1.1 | Columndb90IfSpIndex | read-only | mandatory | Identifies the interface. The value of this object is the same as the ifIndex for this interface. |
| 1.3.6.1.4.1.36.2.18.10.5.3.5.3.1.2 | Columndb90IfSpDesigRootAge | read-only | mandatory | The age, in hundredths of a second, of the last hello message received from the designated bridge on the line. |
| 1.3.6.1.4.1.36.2.18.10.5.3.5.3.1.3 | Columndb90IfSpForwardDelayTimer | read-only | mandatory | The time remaining, in hundredths of a second, before the bridge will leave the learning state of Preforwarding, and enter the Forwarding state. |
| 1.3.6.1.4.1.36.2.18.10.5.3.5.3.1.4 | Columndb90IfSpBadHelloCounts | read-only | mandatory | The number of hello intervals during which at least one bad hello was received. |
| 1.3.6.1.4.1.36.2.18.10.5.3.5.3.1.5 | Columndb90IfSpTopologyChangeAckFlag | read-only | mandatory | A flag that indicates whether a topology change notification received on a link that we are designated on needs to be acknowledged. |
| 1.3.6.1.4.1.36.2.18.10.5.3.6 | Nodedb90ProtoFilt | |||
| 1.3.6.1.4.1.36.2.18.10.5.3.6.1 | Scalardb90ProtoFilterOther | read-only | mandatory | Action taken by the bridge on Ethernet protocol types or the 5-byte SNAP SAPs other than those specified in the db90ProtoTable. forward(1) indicates that a 'fi… |
| 1.3.6.1.4.1.36.2.18.10.5.3.6.2 | Tabledb90ProtoFilterTable | not-accessible | mandatory | A table that contains filtering information about Ethernet protocol types and 5 byte SNAP SAPs for the DECbridge 90. |
| 1.3.6.1.4.1.36.2.18.10.5.3.6.2.1 | Rowdb90ProtoFilterEntry | not-accessible | mandatory | A table that contains filtering characteristics for Ethernet protocol types and 5 byte SNAP SAPs for the DECbridge 90. |
| 1.3.6.1.4.1.36.2.18.10.5.3.6.2.1.1 | Columndb90ProtoFilterProtocol | read-write | mandatory | The protocol type or SNAP SAP in a frame to which this entry's filtering information applies. The length is 2 for Ethernet protocol types and 5 for SNAP SAP. |
| 1.3.6.1.4.1.36.2.18.10.5.3.6.2.1.2 | Columndb90ProtoFilterType | read-write | mandatory | The type of this entry. unknown(1) specifies that this protocol filter is unused. invalid(2) deletes the filter. ethernet(3) or snap-sap(4) defines the size of… |
| 1.3.6.1.4.1.36.2.18.10.5.3.6.2.1.3 | Columndb90ProtoFilterStatus | read-write | mandatory | Action taken by the bridge when it sees this Ethernet protocol type or SNAP SAP in a received frame. Note that this value must be identical to db90ProtoFilterO… |
| 1.3.6.1.4.1.36.2.18.10.5.3.6.2.1.4 | Columndb90ProtoFilterMulticastFlag | read-write | mandatory | Identifies whether or not filtering is based on the multicast bit in the MAC destination address. If allFrames(1), then filtering is performed as per db90Proto… |
| 1.3.6.1.4.1.36.2.18.10.5.3.6.2.1.5 | Columndb90ProtoFilterPortMask | read-write | mandatory | Must be allPorts(3) unless db90ProtoFilterMulticastFlag is multicastOnly, in which case any specification is valid. |