DOCS-PNM-MIB
295 objects
This MIB module contains management objects for the management of DOCSIS 3.1 Proactive Network Maintenance. Copyright 2015-2017 Cable Television Laboratories, Inc. All rights reserved.
Imported Objects
| CLAB-DEF-MIB | clabProjDocsis |
| DOCS-IF-MIB | -- RFC 4001 TenthdB |
| DOCS-IF3-MIB | -- RFC 2863 docsIf3CmSpectrumAnalysisCtrlCmd |
| DOCS-IF31-MIB | -- RFC 4546 DsOfdmModulationType |
| IF-MIB | -- RFC 3411 ifIndex InterfaceIndex InterfaceIndexOrZero |
| INET-ADDRESS-MIB | InetAddress InetAddressType |
| SNMP-FRAMEWORK-MIB | -- RFC 2580 SnmpAdminString |
| SNMPv2-CONF | -- RFC 2579 OBJECT-GROUP MODULE-COMPLIANCE |
| SNMPv2-SMI | Counter64 Integer32 MODULE-IDENTITY OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | -- RFC 2578 TEXTUAL-CONVENTION MacAddress RowStatus TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.4491.2.1.20.1.34.10 | ScalardocsIf3CmSpectrumAnalysisCtrlCmdFileEnable | read-write | current | This attribute, when set to 'true', causes the CM to begin a Spectrum Analysis measurement with the parameters defined by the docsIf3CmSpectrumAnalysisCtrlCmd … |
| 1.3.6.1.4.1.4491.2.1.20.1.34.11 | ScalardocsIf3CmSpectrumAnalysisCtrlCmdMeasStatus | read-only | current | This attribute is used to determine the status of the measurement. An application server will query this value to determine when the file is ready for transfer. |
| 1.3.6.1.4.1.4491.2.1.20.1.34.12 | ScalardocsIf3CmSpectrumAnalysisCtrlCmdFileName | read-write | current | This attribute is the name of the file containing the spectrum analysis data. This value can only be changed while a test is not in progress. An attempt to set… |
| 1.3.6.1.4.1.4491.2.1.27 | IdentitydocsPnmMIB | This MIB module contains management objects for the management of DOCSIS 3.1 Proactive Network Maintenance. Copyright 2015-2017 Cable Television Laboratories, … | ||
| 1.3.6.1.4.1.4491.2.1.27.0 | NodedocsPnmNotifications | |||
| 1.3.6.1.4.1.4491.2.1.27.1 | NodedocsPnmMibObjects | |||
| 1.3.6.1.4.1.4491.2.1.27.1.1 | NodedocsPnmBulkData | |||
| 1.3.6.1.4.1.4491.2.1.27.1.1.1 | NodedocsPnmBulkCtl | |||
| 1.3.6.1.4.1.4491.2.1.27.1.1.1.1 | ScalardocsPnmBulkDestIpAddrType | read-write | current | This object represents the IP address type of the 'docsPnmBulkDestIpAddr' object. This value is of type InetAddressType which is defined by RFC4001. Allowed va… |
| 1.3.6.1.4.1.4491.2.1.27.1.1.1.2 | ScalardocsPnmBulkDestIpAddr | read-write | current | This object represents the IP address of the server to which the bulk data file is to be sent. This attribute is further defined by the 'docsPnmBulkDestIpAddrT… |
| 1.3.6.1.4.1.4491.2.1.27.1.1.1.3 | ScalardocsPnmBulkDestPath | read-write | current | This object represents the path, excluding the filename, at the server to which the captured data file is to be sent. The CM must NOT allow the value of docsPn… |
| 1.3.6.1.4.1.4491.2.1.27.1.1.1.4 | ScalardocsPnmBulkUploadControl | read-write | current | This attribute controls the action taken by the device when a new bulk data file is generated. The possible values are defined below. noAutoUpload - Bulk Data … |
| 1.3.6.1.4.1.4491.2.1.27.1.1.2 | TabledocsPnmBulkFileTable | not-accessible | current | This table provides the objects needed for the device to upload a bulk data file to the Server. This object is a table with a row for each file that is availab… |
| 1.3.6.1.4.1.4491.2.1.27.1.1.2.1 | RowdocsPnmBulkFileEntry | not-accessible | current | The conceptual row of the 'docsPnmBulkFileTable'. An instance is dynamically created and exists for each file that is available for upload. The device must cre… |
| 1.3.6.1.4.1.4491.2.1.27.1.1.2.1.1 | ColumndocsPnmBulkFileIndex | not-accessible | current | This object is the index for the table. |
| 1.3.6.1.4.1.4491.2.1.27.1.1.2.1.2 | ColumndocsPnmBulkFileName | read-only | current | This object contains the name of the bulk data file stored in the device, that is available to be uploaded to the server. Filenames are defined by the applicat… |
| 1.3.6.1.4.1.4491.2.1.27.1.1.2.1.3 | ColumndocsPnmBulkFileControl | read-write | current | This object controls the action taken by the device regarding the file specified by the 'docsPnmBulkFileName' object. When a value is written to this object fo… |
| 1.3.6.1.4.1.4491.2.1.27.1.1.2.1.4 | ColumndocsPnmBulkFileUploadStatus | read-only | current | This attribute reflects the status of the bulk data file. The possible values are listed below. other(1) - Any condition not covered by the other defined value… |
| 1.3.6.1.4.1.4491.2.1.27.1.2 | NodedocsPnmCmObjects | |||
| 1.3.6.1.4.1.4491.2.1.27.1.2.1 | NodedocsPnmCmControlObjects | |||
| 1.3.6.1.4.1.4491.2.1.27.1.2.1.1 | ScalardocsPnmCmCtlTest | read-only | current | This attribute represents the current test. The value could represent the current test in-progress or if no test is running, the last test that was attempted. … |
| 1.3.6.1.4.1.4491.2.1.27.1.2.1.2 | ScalardocsPnmCmCtlTestDuration | read-only | current | This attribute represents the number of seconds that the test specified in 'PnmCmCtlTest' spent with a 'PnmCmCtlStatus' of 'testInProgress'. This serves to pro… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.1.3 | ScalardocsPnmCmCtlStatus | read-only | current | This attribute represents the overall status of the PNM test platform. Individual tests, within the PNM test suite, have their own specific objects to start an… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.2 | TabledocsPnmCmDsOfdmSymCapTable | not-accessible | current | The purpose of downstream symbol capture is to provide partial functionality of a network analyzer to analyze the response of the cable plant from the CM's per… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.2.1 | RowdocsPnmCmDsOfdmSymCapEntry | not-accessible | current | The conceptual row of the docsPnmCmDsOfdmSymCapTable. An instance is dynamically created and exists for an associated ifIndex of the physical downstream channe… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.2.1.1 | ColumndocsPnmCmDsOfdmSymTrigEnable | read-write | current | If this attribute is set to a value of 'true' the CM must begin looking for the presence of the Trigger Message Block in the PLC with a Group ID matching the C… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.2.1.2 | ColumndocsPnmCmDsOfdmSymTrigEnableTimeout | read-write | current | This attribute is used to disable the TrigEnable if no PLC containing a Group ID matching the CM's TrigGroupId in a Trigger Message Block is received within th… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.2.1.3 | ColumndocsPnmCmDsOfdmSymTrigGroupId | read-write | current | This attribute is used to associate a CM with a group of CMs expected to perform Symbol Capture measurements for the designated symbol. This value can only be … |
| 1.3.6.1.4.1.4491.2.1.27.1.2.2.1.4 | ColumndocsPnmCmDsOfdmSymRxWindowing | read-only | current | This attribute is a flag indicating if vendor proprietary receiver windowing was enabled during the capture. |
| 1.3.6.1.4.1.4491.2.1.27.1.2.2.1.5 | ColumndocsPnmCmDsOfdmSymTransactionId | read-only | current | This attribute is the Transaction ID sent by the CMTS in the Trigger Message Block. The CMTS increments this field by one on each trigger message that is sent,… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.2.1.6 | ColumndocsPnmCmDsOfdmSymSampleRate | read-only | current | This attribute is the FFT sample rate in use by the CM for the channel. Typically the sample rate for the downstream channel will be 204.8MHz. |
| 1.3.6.1.4.1.4491.2.1.27.1.2.2.1.7 | ColumndocsPnmCmDsOfdmSymFftLength | read-only | current | This attribute is the FFT length in use by the CM for the channel; typically this value is 4096 or 8192 for the Downstream Channel. |
| 1.3.6.1.4.1.4491.2.1.27.1.2.2.1.8 | ColumndocsPnmCmDsOfdmSymMeasStatus | read-only | current | This attribute is used to determine the status of the measurement. The PNM server will query this value to determine when the file is ready for transfer. |
| 1.3.6.1.4.1.4491.2.1.27.1.2.2.1.9 | ColumndocsPnmCmDsOfdmSymCaptFileName | read-write | current | This attribute is the name of the file, at the CM and containing captured symbol data, which is to be downloaded by the PNM server. This value can only be chan… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.3 | TabledocsPnmCmOfdmChanEstCoefTable | not-accessible | current | The purpose of this table is for the CM to report its estimate of the downstream channel response. The reciprocals of the channel response coefficients are typ… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.3.1 | RowdocsPnmCmOfdmChanEstCoefEntry | not-accessible | current | The conceptual row of the docsPnmCmOfdmChanEstCoefTable. An instance is dynamically created and exists for an associated ifIndex of the physical downstream cha… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.3.1.1 | ColumndocsPnmCmOfdmChEstCoefTrigEnable | read-write | current | Setting this object to a value of 'true' instructs the CM to begin collection and storing the channel estimate coefficients into the file specified by the 'doc… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.3.1.2 | ColumndocsPnmCmOfdmChEstCoefAmpRipplePkToPk | read-only | current | This attribute represents the value of the peak to peak ripple in the magnitude of the equalizer coefficients [PHYv3.1]. The slope component calculated for the… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.3.1.3 | ColumndocsPnmCmOfdmChEstCoefAmpRippleRms | read-only | current | This attribute represents the value of the RMS ripple in the magnitude of the equalizer coefficients. The slope component calculated for the AmplitudeSlope is … |
| 1.3.6.1.4.1.4491.2.1.27.1.2.3.1.4 | ColumndocsPnmCmOfdmChEstCoefAmpSlope | read-only | current | This attribute represents the slope in 0.001 dB per MHz in the magnitude of the equalizer coefficients. The slope is calculated as the slope of a linear least … |
| 1.3.6.1.4.1.4491.2.1.27.1.2.3.1.5 | ColumndocsPnmCmOfdmChEstCoefGrpDelayRipplePkToPk | read-only | current | This attribute represents the peak-to-peak group delay ripple expressed in units of 0.001 nsec. This attribute represents the group delay variation across the … |
| 1.3.6.1.4.1.4491.2.1.27.1.2.3.1.6 | ColumndocsPnmCmOfdmChEstCoefGrpDelayRippleRms | read-only | current | This attribute represents the RMS value of the group delay ripple expressed in units of 0.001 nsec. This attribute represents the group delay variation across … |
| 1.3.6.1.4.1.4491.2.1.27.1.2.3.1.7 | ColumndocsPnmCmOfdmChEstCoefMeasStatus | read-only | current | This attribute is used to determine the status of the measurement. The PNM server will query this value to determine when the file is ready for transfer. |
| 1.3.6.1.4.1.4491.2.1.27.1.2.3.1.8 | ColumndocsPnmCmOfdmChEstCoefFileName | read-write | current | This attribute is the name of the file at the CM which is to be transferred to the PNM server. The data is stored as 16 bit integers for the I and Q data. This… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.3.1.9 | ColumndocsPnmCmOfdmChEstCoefAmpMean | read-only | current | This attribute represents the mean, in 0.001 dB, of the magnitude of the equilizer coefficients. |
| 1.3.6.1.4.1.4491.2.1.27.1.2.3.1.10 | ColumndocsPnmCmOfdmChEstCoefGrpDelaySlope | read-only | current | This attribute represents the slope in 0.001 nsec per MHz in the group delay of the equalizer coefficients. This attribute represents the slope across the enti… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.3.1.11 | ColumndocsPnmCmOfdmChEstCoefGrpDelayMean | read-only | current | This attribute represents the mean of the group delay, in units of 0.001 nsec. |
| 1.3.6.1.4.1.4491.2.1.27.1.2.4 | TabledocsPnmCmDsConstDispMeasTable | not-accessible | current | The downstream constellation display provides received QAM constellation points for display. Equalized soft decisions (I and Q) at the slicer input are collect… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.4.1 | RowdocsPnmCmDsConstDispMeasEntry | not-accessible | current | The conceptual row of the docsPnmCmDsConstDispMeasTable. An instance is dynamically created and exists for an associated ifIndex upon which the test defined by… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.4.1.1 | ColumndocsPnmCmDsConstDispTrigEnable | read-write | current | Setting this object to a value of 'true' instructs the CM to begin collection and storing the constellation points into the file specified by the 'docsPnmCmDsC… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.4.1.2 | ColumndocsPnmCmDsConstDispModOrderOffset | read-write | current | This attribute specifies an offset from the lowest order modulation for the data subcarriers in any of the profiles in the downstream channel. If the lowest or… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.4.1.3 | ColumndocsPnmCmDsConstDispNumSampleSymb | read-write | current | This attribute tells the CM how many soft decision samples of OFDM subcarriers with the specified modulation order are captured. This value can only be changed… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.4.1.4 | ColumndocsPnmCmDsConstDispSelModOrder | read-only | current | This object provides the actual Modulation Order that will be used for the Constellation display based on the selected ModulationOrderOffset. |
| 1.3.6.1.4.1.4491.2.1.27.1.2.4.1.5 | ColumndocsPnmCmDsConstDispMeasStatus | read-only | current | This attribute is used to determine the status of the measurement. The PNM server will query this value to determine when the file is ready for transfer. |
| 1.3.6.1.4.1.4491.2.1.27.1.2.4.1.6 | ColumndocsPnmCmDsConstDispFileName | read-write | current | This attribute is the name of the file at the CM which is to be transferred to the PNM server. The data is stored as 16 bit integers for the I and Q data. This… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.5 | TabledocsPnmCmDsOfdmRxMerTable | not-accessible | current | This item provides measurements of the receive modulation error ratio (RxMER) for each subcarrier. Each subcarrier RxMER value consists of one byte which repre… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.5.1 | RowdocsPnmCmDsOfdmRxMerEntry | not-accessible | current | The conceptual row of the docsPnmCmDsOfdmRxMerTable. An instance is dynamically created and exists for an associated ifIndex upon which the test defined by thi… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.5.1.1 | ColumndocsPnmCmDsOfdmRxMerFileEnable | read-write | current | This attribute causes the CM to begin the RxMer measurement for the purpose of creating a file of RxMer data. When the measurement is complete the FileEnable a… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.5.1.2 | ColumndocsPnmCmDsOfdmRxMerPercentile | read-write | current | This attribute specifies the percentile (such as 2nd percentile or 5th percentile) of all active subcarriers in an OFDM channel at which the ThresholdRxMerValu… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.5.1.3 | ColumndocsPnmCmDsOfdmRxMerMean | read-only | current | This attribute is the mean of the dB values of the RxMER measurements of all active subcarriers. The mean is computed directly on the dB values as follows: Mea… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.5.1.4 | ColumndocsPnmCmDsOfdmRxMerStdDev | read-only | current | This attribute is the standard deviation of the dB values of the RxMER measurements of all active subcarriers. The standard deviation is computed directly on t… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.5.1.5 | ColumndocsPnmCmDsOfdmRxMerThrVal | read-only | current | This attribute is the RxMER value corresponding to the specified Percentile value. The CM sorts the subcarriers in ascending order of RxMER, resulting in a pos… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.5.1.6 | ColumndocsPnmCmDsOfdmRxMerThrHighestFreq | read-only | current | This attribute is the frequency in Hz of the highest-frequency subcarrier having RxMER = ThresholdRxMerValue. |
| 1.3.6.1.4.1.4491.2.1.27.1.2.5.1.7 | ColumndocsPnmCmDsOfdmRxMerMeasStatus | read-only | current | This attribute is used to determine the status of the measurement. The PNM server will query this value to determine when the file is ready for transfer. |
| 1.3.6.1.4.1.4491.2.1.27.1.2.5.1.8 | ColumndocsPnmCmDsOfdmRxMerFileName | read-write | current | This attribute is the name of the file at the CM which is to be downloaded by the PNM server. This value can only be changed while a test is not in progress. A… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.6 | TabledocsPnmCmDsOfdmMerMarTable | not-accessible | current | The purpose of this item is to provide an estimate of the MER margin available on the downstream data channel with respect to a candidate modulation profile. T… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.6.1 | RowdocsPnmCmDsOfdmMerMarEntry | not-accessible | current | The conceptual row of the docsPnmCmDsOfdmMerMarTable. An instance is dynamically created and exists for an associated ifIndex upon which the test defined by th… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.6.1.1 | ColumndocsPnmCmDsOfdmMerMarProfileId | read-write | current | This attribute represents the Downstream Profile ID of the candidate Profile. This value can only be changed while a test is not in progress. An attempt to set… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.6.1.2 | ColumndocsPnmCmDsOfdmMerMarThrshldOffset | read-write | current | This attribute represents the number of dB below the RequiredDsOfdmQamMer value which is likely to cause uncorrectable errors. Measurements of Subcarrier MER t… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.6.1.3 | ColumndocsPnmCmDsOfdmMerMarMeasEnable | read-write | current | This attribute causes the CM to begin the measurement. When the measurement is complete the MeasEnable attribute is set internally to 'false' by the CM. Settin… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.6.1.4 | ColumndocsPnmCmDsOfdmMerMarNumSymPerSubCarToAvg | read-write | current | This attribute represents the number of symbols that will be used in the calculation of the average MER per subcarrier. This value can only be changed while a … |
| 1.3.6.1.4.1.4491.2.1.27.1.2.6.1.5 | ColumndocsPnmCmDsOfdmMerMarReqAvgMer | read-write | current | This attribute represents the minimum required average MER. The CM subtracts this value from the MeasuredAvgMer to obtain the AverageMerMargin. If this value i… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.6.1.6 | ColumndocsPnmCmDsOfdmMerMarNumSubCarBelowThrshld | read-only | current | This object represents the number of subcarriers which were counted due to satisfying the criteria defined for the 'docsPnmCmDsOfdmMerMarThrshldOffset' object. |
| 1.3.6.1.4.1.4491.2.1.27.1.2.6.1.7 | ColumndocsPnmCmDsOfdmMerMarMeasuredAvgMer | read-only | current | This attribute is the average of all MER dB values measured over all of the subcarriers. That is, the average is taken of all the dB values. |
| 1.3.6.1.4.1.4491.2.1.27.1.2.6.1.8 | ColumndocsPnmCmDsOfdmMerMarAvgMerMargin | read-only | current | This attribute represents the difference between the 'docsPnmCmDsOfdmMerMarMeasuredAvgMer' and the 'docsPnmCmDsOfdmMerMarReqAvgMer'. |
| 1.3.6.1.4.1.4491.2.1.27.1.2.6.1.9 | ColumndocsPnmCmDsOfdmMerMarMeasStatus | read-only | current | This attribute is used to determine the status of the measurement. The PNM server will query this value to determine when the data is ready for evaluation. |
| 1.3.6.1.4.1.4491.2.1.27.1.2.7 | TabledocsPnmCmDsOfdmFecTable | not-accessible | current | The purpose of the table is to provide a series of codword error rate measurements on a per profle basis over a set period of time. This table will have a row … |
| 1.3.6.1.4.1.4491.2.1.27.1.2.7.1 | RowdocsPnmCmDsOfdmFecEntry | not-accessible | current | The conceptual row of the docsPnmCmDsOfdmFecTable. An instance is dynamically created and exists for an associated ifIndex upon which the test defined by this … |
| 1.3.6.1.4.1.4491.2.1.27.1.2.7.1.1 | ColumndocsPnmCmDsOfdmFecSumType | read-write | current | This attribute is the type of summary test to be performed. If set to 'interval10min(2)', when enabled the CM must perform a test of 10 minutes in duration rec… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.7.1.2 | ColumndocsPnmCmDsOfdmFecFileEnable | read-write | current | When this attribute is set to 'true' the CM must begin the SummaryType codeword error summary test. While the test is in progress, the CM must return a MeasSta… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.7.1.3 | ColumndocsPnmCmDsOfdmFecMeasStatus | read-only | current | This attribute is used to determine the status of the measurement. The PNM server will query this value to determine when the file is ready for transfer. |
| 1.3.6.1.4.1.4491.2.1.27.1.2.7.1.4 | ColumndocsPnmCmDsOfdmFecFileName | read-write | current | This attribute is the name of the file at the CM which is to be transferred to the PNM server. This value can only be changed while a test is not in progress. … |
| 1.3.6.1.4.1.4491.2.1.27.1.2.8 | NodedocsPnmCmDsOfdmReqMERObjects | |||
| 1.3.6.1.4.1.4491.2.1.27.1.2.8.1 | ScalardocsPnmCmDsOfdmReqMerQam16 | read-write | current | This attribute represents the minimum required MER value for this Modulation Order. It is used in determining the SNR Margin for the Candidate Downstream Profi… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.8.2 | ScalardocsPnmCmDsOfdmReqMerQam64 | read-write | current | This attribute represents the minimum required MER value for this Modulation Order. It is used in determining the SNR Margin for the Candidate Downstream Profi… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.8.3 | ScalardocsPnmCmDsOfdmReqMerQam128 | read-write | current | This attribute represents the minimum required MER value for this Modulation Order. It is used in determining the SNR Margin for the Candidate Downstream Profi… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.8.4 | ScalardocsPnmCmDsOfdmReqMerQam256 | read-write | current | This attribute represents the minimum required MER value for this Modulation Order. It is used in determining the SNR Margin for the Candidate Downstream Profi… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.8.5 | ScalardocsPnmCmDsOfdmReqMerQam512 | read-write | current | This attribute represents the minimum required MER value for this Modulation Order. It is used in determining the SNR Margin for the Candidate Downstream Profi… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.8.6 | ScalardocsPnmCmDsOfdmReqMerQam1024 | read-write | current | This attribute represents the minimum required MER value for this Modulation Order. It is used in determining the SNR Margin for the Candidate Downstream Profi… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.8.7 | ScalardocsPnmCmDsOfdmReqMerQam2048 | read-write | current | This attribute represents the minimum required MER value for this Modulation Order. It is used in determining the SNR Margin for the Candidate Downstream Profi… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.8.8 | ScalardocsPnmCmDsOfdmReqMerQam4096 | read-write | current | This attribute represents the minimum required MER value for this Modulation Order. It is used in determining the SNR Margin for the Candidate Downstream Profi… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.8.9 | ScalardocsPnmCmDsOfdmReqMerQam8192 | read-write | current | This attribute represents the minimum required MER value for this Modulation Order. It is used in determining the SNR Margin for the Candidate Downstream Profi… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.8.10 | ScalardocsPnmCmDsOfdmReqMerQam16384 | read-write | current | This attribute represents the minimum required MER value for this Modulation Order. It is used in determining the SNR Margin for the Candidate Downstream Profi… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.9 | TabledocsPnmCmDsHistTable | not-accessible | current | The purpose of the downstream histogram is to provide a measurement of nonlinear effects in the channel such as amplifier compression and laser clipping. For e… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.9.1 | RowdocsPnmCmDsHistEntry | not-accessible | current | The conceptual row of the docsPnmCmDsHistTable. An instance is dynamically created and exists for an associated ifIndex of the RF MAC interface upon which the … |
| 1.3.6.1.4.1.4491.2.1.27.1.2.9.1.1 | ColumndocsPnmCmDsHistEnable | read-write | current | Setting this object to a value of 'true' instructs the CM to begin collection of histogram data and when enabled, the CM continues producing new data at its ow… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.9.1.2 | ColumndocsPnmCmDsHistTimeOut | read-write | current | This object sets a seconds time-out timer for capturing histogram data. This attribute is used to automatically clear the Enable attribute when the timeout exp… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.9.1.3 | ColumndocsPnmCmDsHistMeasStatus | read-only | current | This attribute is used to determine the status of the measurement. The PNM server will query this value to determine when the file is ready for transfer. |
| 1.3.6.1.4.1.4491.2.1.27.1.2.9.1.4 | ColumndocsPnmCmDsHistFileName | read-write | current | This object is the name of the file at the CM which is to be transferred to the PNM server. The data is stored as 32 bit integers for the hit and dwell count v… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.10 | TabledocsPnmCmUsPreEqTable | not-accessible | current | This object provides access to CM upstream pre-equalizer coefficients. The CM pre-equalizer coefficients and the CMTS upstream adaptive equalizer coefficient u… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.10.1 | RowdocsPnmCmUsPreEqEntry | not-accessible | current | The conceptual row of the docsPnmCmUsPreEqTable. An instance is dynamically created and exists for an associated ifIndex upon which the test defined by this ta… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.10.1.1 | ColumndocsPnmCmUsPreEqFileEnable | read-write | current | This object causes the files defined by the 'docsPnmCmUsPreEqFileName' and the 'docsPnmCmUsPreEqlastUpdateFileName' objects to be created. The files, once crea… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.10.1.2 | ColumndocsPnmCmUsPreEqAmpRipplePkToPk | read-only | current | This attribute represents the value of the peak to peak ripple in the magnitude of the equalizer coefficients. This attribute represents the ripple across the … |
| 1.3.6.1.4.1.4491.2.1.27.1.2.10.1.3 | ColumndocsPnmCmUsPreEqAmpRippleRms | read-only | current | This attribute represents the value of the RMS ripple in the magnitude of the equalizer coefficients. This attribute represents the ripple across the entire OF… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.10.1.4 | ColumndocsPnmCmUsPreEqAmpSlope | read-only | current | This attribute represents the slope in 0.001 dB per MHz in the magnitude of the equalizer coefficients. This attribute represents the slope across the entire O… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.10.1.5 | ColumndocsPnmCmUsPreEqGrpDelayRipplePkToPk | read-only | current | This attribute represents the peak-to-peak Group Delay Ripple expressed in units of 0.001 nsec. This attribute represents the group delay variation across the … |
| 1.3.6.1.4.1.4491.2.1.27.1.2.10.1.6 | ColumndocsPnmCmUsPreEqGrpDelayRippleRms | read-only | current | This attribute represents the RMS value of the Group Delay Ripple expressed in units of 0.001 nsec. This attribute represents the group delay variation across … |
| 1.3.6.1.4.1.4491.2.1.27.1.2.10.1.7 | ColumndocsPnmCmUsPreEqPreEqCoAdjStatus | read-only | current | This object represents whether the last set of Pre-Equalization coefficient adjustments that were fully applied or were only partially applied due to excessive… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.10.1.8 | ColumndocsPnmCmUsPreEqMeasStatus | read-only | current | This attribute is used to determine the status of the measurement. The PNM server will query this value to determine when the file is ready for transfer. Summa… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.10.1.9 | ColumndocsPnmCmUsPreEqLastUpdateFileName | read-write | current | This attribute is the name of the file at the CM which is to be transferred to the PNM server. The data represents the values sent to the CM by the CMTS in the… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.10.1.10 | ColumndocsPnmCmUsPreEqFileName | read-write | current | This attribute is the name of the file at the CM which is to be transferred to the PNM server. The data represents the current value of the Pre-Equalization va… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.10.1.11 | ColumndocsPnmCmUsPreEqAmpMean | read-only | current | This attribute represents the mean in 0.001 dB, of the magnitude of the equalizer coefficients. Note: An algorithm for calculating the ripple and slope for the… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.10.1.12 | ColumndocsPnmCmUsPreEqGrpDelaySlope | read-only | current | This attribute represents the slope in 0.001 nsec per MHz in the group delay of the equalizer coefficients. This attribute represents the slope across the enti… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.10.1.13 | ColumndocsPnmCmUsPreEqGrpDelayMean | read-only | current | This attribute represents the mean of the group delay in units of 0.001 nsec. |
| 1.3.6.1.4.1.4491.2.1.27.1.2.11 | TabledocsPnmCmDsOfdmModProfTable | not-accessible | current | The purpose of the table is to provide the per subcarrier bit load of the modulation profiles. This table will have a row for each ifIndex for the modem. |
| 1.3.6.1.4.1.4491.2.1.27.1.2.11.1 | RowdocsPnmCmDsOfdmModProfEntry | not-accessible | current | The conceptual row of the docsPnmCmDsOfdmModProfTable. An instance is dynamically created and exists for an associated ifIndex upon which the test defined by t… |
| 1.3.6.1.4.1.4491.2.1.27.1.2.11.1.1 | ColumndocsPnmCmDsOfdmModProfFileEnable | read-write | current | When this attribute is set to 'true' the CM must begin the Modulation Profile Summary report. While the report is in progress, the CM must return a MeasStatus … |
| 1.3.6.1.4.1.4491.2.1.27.1.2.11.1.2 | ColumndocsPnmCmDsOfdmModProfMeasStatus | read-only | current | This attribute is used to determine the status of the measurement. The PNM server will query this value to determine when the file is ready for transfer. |
| 1.3.6.1.4.1.4491.2.1.27.1.2.11.1.3 | ColumndocsPnmCmDsOfdmModProfFileName | read-write | current | This attribute is the name of the file at the CM which is to be transferred to the PNM server. This value can only be changed while a test is not in progress. … |
| 1.3.6.1.4.1.4491.2.1.27.1.3 | NodedocsPnmCmtsObjects | |||
| 1.3.6.1.4.1.4491.2.1.27.1.3.1 | TabledocsPnmCmtsDsOfdmSymCapTable | not-accessible | current | The DsOfdmSymbolCapture object capture provides partial functionality of a network analyzer to analyze the response of the cable plant. At the CMTS, the transm… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.1.1 | RowdocsPnmCmtsDsOfdmSymCapEntry | not-accessible | current | The conceptual row of the 'docsPnmCmtsDsOfdmSymCapTable'. An instance is dynamically created and exists for an associated ifIndex of the physical downstream ch… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.1.1.1 | ColumndocsPnmCmtsDsOfdmSymTrigEnable | read-write | current | Setting this object to a value of 'true' instructs the CMTS to insert a Trigger Message Block in the PLC with a Group ID matching the CM's TriggerGroupID. The … |
| 1.3.6.1.4.1.4491.2.1.27.1.3.1.1.2 | ColumndocsPnmCmtsDsOfdmSymTrigGroupId | read-write | current | This attribute is used by the CMTS to be inserted in the PLC Trigger Message Block to identify a CM or a group of CMs expected to perform Symbol Capture measur… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.1.1.3 | ColumndocsPnmCmtsDsOfdmSymFirstActSubCarIdx | read-only | current | This object is used to denote the subcarrier index of the lowest frequency of the Encompassed Spectrum for the OFDM channel. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.1.1.4 | ColumndocsPnmCmtsDsOfdmSymLastActSubCarIdx | read-only | current | This object is used to denote the subcarrier index of the highest frequency of the Encompassed Spectrum for the OFDM channel. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.1.1.5 | ColumndocsPnmCmtsDsOfdmSymRxWindowing | read-only | current | This attribute is a flag indicating if vendor proprietary windowing was enabled during the capture. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.1.1.6 | ColumndocsPnmCmtsDsOfdmSymTransactionId | read-only | current | This attribute is the Transaction ID sent by the CMTS in the Trigger Message Block. Prior to completion of a measurement this attribute has no meaning. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.1.1.7 | ColumndocsPnmCmtsDsOfdmSymSampleRate | read-only | current | This attribute is the FFT sample rate in use by the CM for the channel; typically the sample rate for the downstream channel will be 204.8MHz. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.1.1.8 | ColumndocsPnmCmtsDsOfdmSymFftLength | read-only | current | This attribute is the FFT length in use by the CM for the channel; typically this value is 4096 or 8192 for the Downstream Channel. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.1.1.9 | ColumndocsPnmCmtsDsOfdmSymMeasStatus | read-only | current | This attribute is used to determine the status of the measurement. The PNM server will query this value to determine when the measurement is complete. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.1.1.10 | ColumndocsPnmCmtsDsOfdmSymCaptFileName | read-write | current | This attribute is the name of the file with the captured symbol data at the CMTS that is to be downloaded using TFTP by the PNM server. This value can only be … |
| 1.3.6.1.4.1.4491.2.1.27.1.3.2 | TabledocsPnmCmtsDsOfdmNoisePwrRatioTable | not-accessible | current | The purpose of downstream NPR measurement is to view the noise, interference and intermodulation products underlying a portion of the OFDM signal. As an out-of… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.2.1 | RowdocsPnmCmtsDsOfdmNoisePwrRatioEntry | not-accessible | current | The conceptual row of the 'docsPnmCmtsDsOfdmNoisePwrRatioTable'. An instance is dynamically created and exists for an associated ifIndex of the physical downst… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.2.1.1 | ColumndocsPnmCmtsDsOfdmNprStartSubcar | read-write | current | This attribute is the Subcarrier index corresponding to the frequency at the start of the spectral notch. This value can only be changed while the value of 'do… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.2.1.2 | ColumndocsPnmCmtsDsOfdmNprStopSubcar | read-write | current | This object is the Subcarrier index corresponding to the frequency at the upper end of the spectral notch. This value can only be changed while the value of 'd… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.2.1.3 | ColumndocsPnmCmtsDsOfdmNprEnable | read-write | current | This object is used to enable the CMTS to create the spectral notch. The CMTS MAY require the interface to have an ifAdminStatus of 'down' before allowing the … |
| 1.3.6.1.4.1.4491.2.1.27.1.3.2.1.4 | ColumndocsPnmCmtsDsOfdmNprDuration | read-write | current | This object indicates the length of time in seconds that the spectral notch is to be maintained. The CMTS MAY make the excluded subcarriers active after the ex… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.3 | TabledocsPnmCmtsUsOfdmaAQProbeTable | not-accessible | current | The purpose of upstream capture is to measure plant response and view the underlying noise floor, by capturing at least one OFDMA symbol during a scheduled act… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.3.1 | RowdocsPnmCmtsUsOfdmaAQProbeEntry | not-accessible | current | The conceptual row of the 'docsPnmCmtsUsOfdmaAQProbeTable'. An instance is dynamically created and exists for an associated ifIndex of the physical upstream ch… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.3.1.1 | ColumndocsPnmCmtsUsOfdmaAQProbeCmMacAddr | read-write | current | This attribute represents the MAC address of the CM transmitting the probe to be measured. This object cannot be changed while a capture is in progress. It wil… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.3.1.2 | ColumndocsPnmCmtsUsOfdmaAQProbeUseIdleSid | read-write | current | This attribute, when enabled, causes the CMTS to measure the channel during a quiet period when no CM is transmitting. This object cannot be changed while a ca… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.3.1.3 | ColumndocsPnmCmtsUsOfdmaAQProbePreEqOn | read-write | current | This attribute, when enabled, causes the CMTS to enable pre-equalization in the Probe Information Element for the CM transmitting the probe to be measured. Thi… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.3.1.4 | ColumndocsPnmCmtsUsOfdmaAQProbeEnable | read-write | current | This attribute causes the CMTS to begin the measurement of a probe for the selected CM or for a quiet period if the UseIdleSid attribute is enabled. The Enable… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.3.1.5 | ColumndocsPnmCmtsUsOfdmaAQProbeTimeout | read-write | current | This attribute provides a timeout for the measurement if the CMTS is unable to perform the measurement for some reason. A value of zero for the Timeout attribu… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.3.1.6 | ColumndocsPnmCmtsUsOfdmaAQProbeNumSymToCapt | read-write | current | This object represents the number of symbols the CMTS is to capture for the modem whose probe is being measured or the number of symbol times to measure for th… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.3.1.7 | ColumndocsPnmCmtsUsOfdmaAQProbeMaxCaptSymbols | read-only | current | This object represents the number of symbols the CMTS can capture for one measurement. Typically for a 50kHz Subcarrier Spacing the CMTS can capture two symbol… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.3.1.8 | ColumndocsPnmCmtsUsOfdmaAQProbeNumSamples | read-only | current | This object represents the number of FFT samples used for the measurement. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.3.1.9 | ColumndocsPnmCmtsUsOfdmaAQProbeTimeStamp | read-only | current | This object represents the timestamp corresponding to the time when the measurement was performed. In the case in which the Primary Downstream is an OFDM chann… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.3.1.10 | ColumndocsPnmCmtsUsOfdmaAQProbeMeasStatus | read-only | current | This attribute is used to determine the status of the measurement. When the Status = 'SampleReady', the CCAP has completed the measurement and the Enable attri… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.3.1.11 | ColumndocsPnmCmtsUsOfdmaAQProbeFileName | read-write | current | This attribute is the name of the file, with the captured probe data, at the CMTS that is to be downloaded using TFTP to the PNM server. This value can only be… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.4 | TabledocsPnmCmtsUsImpNoiseTable | not-accessible | current | This table provides statistics of burst/impulse noise occurring in a selected narrow band. A bandpass filter is positioned in an unoccupied upstream band. A th… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.4.1 | RowdocsPnmCmtsUsImpNoiseEntry | not-accessible | current | The conceptual row of the docsPnmCmtsUsImpNoiseTable. An instance is dynamically created and exists for an associated ifIndex of the physical upstream channel … |
| 1.3.6.1.4.1.4491.2.1.27.1.3.4.1.1 | ColumndocsPnmCmtsUsImpNoiseEnable | read-write | current | This attribute causes the CCAP to begin the collection of the configured Impulse Noise events. If the FreeRunDuration is set to a value greater than zero, the … |
| 1.3.6.1.4.1.4491.2.1.27.1.3.4.1.2 | ColumndocsPnmCmtsUsImpNoiseFreeRunDuration | read-write | current | This attribute provides length of time to perform the measurement when the Enable attribute is set to true. This object cannot be changed while a capture is in… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.4.1.3 | ColumndocsPnmCmtsUsImpNoiseStTrigLvl | read-write | current | If the FreeRunDuration is set to zero and the Enable attribute is set to true, an individual burst event starts when the burst noise exceeds the StartTriggerLe… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.4.1.4 | ColumndocsPnmCmtsUsImpNoiseEndTrigLvl | read-write | current | The measurement of an individual burst event ends when the burst noise falls below the EndTriggerLevel. It is worth noting that if the EndTriggerLevel is set t… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.4.1.5 | ColumndocsPnmCmtsUsImpNoiseCenterFrq | read-write | current | This attribute defines the center frequency for the noise power measurement. This object cannot be changed while a capture is in progress. It will return a val… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.4.1.6 | ColumndocsPnmCmtsUsImpNoiseMeasBw | read-write | current | This attribute defines the bandwidth for the noise power measurement. The MeasurementBw is the -3 dB bandwidth; the occupied bandwidth is typically 1.25 times … |
| 1.3.6.1.4.1.4491.2.1.27.1.3.4.1.7 | ColumndocsPnmCmtsUsImpNoiseNumEvtsCnted | read-only | current | This attribute is used to indicate how many impulse noise events have been recorded since the enable was set to true. This value will be 1024 in steady state, … |
| 1.3.6.1.4.1.4491.2.1.27.1.3.4.1.8 | ColumndocsPnmCmtsUsImpNoiseLastEvtTimeStamp | read-only | current | This attribute provides represents the timestamp corresponding to the start of the last recorded event. The measurement is time-stamped using the 64-bit extend… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.4.1.9 | ColumndocsPnmCmtsUsImpNoiseLastEvtDuration | read-only | current | This attribute provides represents the time corresponding to the duration of the last recorded event. The EventDuration is expressed in ns. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.4.1.10 | ColumndocsPnmCmtsUsImpNoiseLastEvtAvgPwr | read-only | current | This attribute represents the average power measured during the last recorded event. The LastEventAveragePower is expressed in units of dBmV with 32-bit fixed … |
| 1.3.6.1.4.1.4491.2.1.27.1.3.4.1.11 | ColumndocsPnmCmtsUsImpNoiseMeasStatus | read-only | current | This attribute is used to determine the status of the command. When the Status is sampleReady, the CCAP has completed the measurement and the Enable attribute … |
| 1.3.6.1.4.1.4491.2.1.27.1.3.4.1.12 | ColumndocsPnmCmtsUsImpNoiseFileName | read-write | current | This attribute is the name of the file with the captured impulse noise data at the CMTS that is to be downloaded using TFTP to the PNM server. This value can o… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.5 | TabledocsPnmCmtsUsHistTable | not-accessible | current | The Upstream Histogram provides a measurement of nonlinear effects in the channel such as amplifier compression and laser clipping. For example, laser clipping… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.5.1 | RowdocsPnmCmtsUsHistEntry | not-accessible | current | The conceptual row of the docsPnmCmtsUsHistTable. An instance is dynamically created and exists for an associated ifIndex of an upstream RF port upon which the… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.5.1.1 | ColumndocsPnmCmtsUsHistEnable | read-write | current | Setting this object to a value of 'true' instructs the CCAP to begin collection of histogram data and when enabled, the CCAP continues producing new data at it… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.5.1.2 | ColumndocsPnmCmtsUsHistTimeOut | read-write | current | This attribute sets a seconds time-out timer for capturing histogram data. This attribute is used to automatically clear the Enable attribute when the timeout … |
| 1.3.6.1.4.1.4491.2.1.27.1.3.5.1.3 | ColumndocsPnmCmtsUsHistMeasStatus | read-only | current | This attribute is used to determine the status of the measurement. The PNM server will query this value to determine when the file is ready for transfer. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.5.1.4 | ColumndocsPnmCmtsUsHistFileName | read-write | current | This object is the name of the file at the CCAP which is to be transferred to the PNM server. The data is stored as 32 bit integers for the hit and dwell count… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.6 | TabledocsPnmCmtsUsOfdmaRxPwrTable | not-accessible | current | The purpose of the upstream channel power metric is to provide an estimate of the received power in a specified OFDMA channel at the F connector input of the C… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.6.1 | RowdocsPnmCmtsUsOfdmaRxPwrEntry | not-accessible | current | The conceptual row of the docsPnmCmtsUsOfdmaRxPwrTable. An instance is dynamically created and exists for an associated ifIndex upon which the test defined by … |
| 1.3.6.1.4.1.4491.2.1.27.1.3.6.1.1 | ColumndocsPnmCmtsUsOfdmaRxPwrEnable | read-write | current | This attribute causes the CMTS to begin a measurement of the received upstream channel power for the CM whose MAC address was specified in the CmMac attribute.… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.6.1.2 | ColumndocsPnmCmtsUsOfdmaRxPwrCmMac | not-accessible | current | This attribute represents the MAC address of the CM whose Received upstream channel power is being measured. This object cannot be changed while a capture is i… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.6.1.3 | ColumndocsPnmCmtsUsOfdmaRxPwrPreEq | read-write | current | This attribute is used by the CMTS to enable or disable pre-equalization of the probe. The pre-equalization is controlled by a bit in the Probe Information Ele… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.6.1.4 | ColumndocsPnmCmtsUsOfdmaRxPwrNumAvgs | read-write | current | This attribute controls the time average over the number of probes the CCAP will use to calculate the docsPnmCmtsUsOfdmaRxPwrOnePtSix. The average is simply th… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.6.1.5 | ColumndocsPnmCmtsUsOfdmaRxPwrOnePtSixPsd | read-only | current | This attribute represents the average power of the probe measured by the CCAP, reported as the Power Spectral Density in an equivalent 1.6 MHz spectrum, for th… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.6.1.6 | ColumndocsPnmCmtsUsOfdmaRxPwrMeasStatus | read-only | current | This attribute is used to determine the status of the measurement. When the Status = SampleReady, the CCAP is ready for the Upstream Power data to be read. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.7 | TabledocsPnmCmtsUsOfdmaRxMerTable | not-accessible | current | This item provides measurements of the upstream receive modulation error ratio (RxMER) for each subcarrier. The CMTS measures the RxMER using an upstream probe… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.7.1 | RowdocsPnmCmtsUsOfdmaRxMerEntry | not-accessible | current | The conceptual row of the docsPnmCmtsUsOfdmaRxMerTable. An instance is dynamically created and exists for an associated ifIndex upon which the test defined by … |
| 1.3.6.1.4.1.4491.2.1.27.1.3.7.1.1 | ColumndocsPnmCmtsUsOfdmaRxMerEnable | read-write | current | This attribute causes the CMTS to begin a measurement of the received MER per subcarrier for the CM whose MAC address was specified in the CmMac attribute. Int… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.7.1.2 | ColumndocsPnmCmtsUsOfdmaRxMerCmMac | read-write | current | This attribute represents the MAC address of the CM whose Rx MER is being measured. This object cannot be changed while a capture is in progress. It will retur… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.7.1.3 | ColumndocsPnmCmtsUsOfdmaRxMerPreEq | read-write | current | This attribute is used by the CMTS to enable or disable Pre Equalization of the probe. The Pre Equalization is controlled by a bit in the Probe Information Ele… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.7.1.4 | ColumndocsPnmCmtsUsOfdmaRxMerNumAvgs | read-write | current | This attribute controls the number of probes the CMTS will use to calculate the Rx MER per subcarrier. The average will be computed using the 'leaky integrator… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.7.1.5 | ColumndocsPnmCmtsUsOfdmaRxMerMeasStatus | read-only | current | This attribute is used to determine the status of the measurement. When the MeasStatus = SampleReady, the CMTS is ready for the RxMER data to be read. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.7.1.6 | ColumndocsPnmCmtsUsOfdmaRxMerFileName | read-write | current | This attribute is the name of the file with the RxMER data for a specified CM at the CMTS that is to be downloaded using TFTP to the PNM server. This value can… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.8 | TabledocsPnmCmtsUsSpecAnTable | not-accessible | deprecated | The upstream triggered spectrum analysis measurement provides a wideband spectrum analyzer function in the CMTS which can be triggered to examine desired upstr… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.8.1 | RowdocsPnmCmtsUsSpecAnEntry | not-accessible | deprecated | The conceptual row of the docsPnmCmtsUsSpecAnTable. An instance is dynamically created and exists for an associated ifIndex of an OFDMA upstream RF Port upon w… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.8.1.1 | ColumndocsPnmCmtsUsSpecAnEnable | read-write | deprecated | This attribute causes the CMTS to begin the measurement of a probe for the selected CM or for a quiet period if the UseIdleSid attribute is enabled. The Enable… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.8.1.2 | ColumndocsPnmCmtsUsSpecAnTrigMode | read-write | deprecated | This attribute is used to control the trigger mode for the Spectrum Analysis capture. This object cannot be changed while a capture is in progress. It will ret… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.8.1.3 | ColumndocsPnmCmtsUsSpecAnMiniSlotCnt | read-write | deprecated | This attribute controls the numbe rof minislots the CMTS capturs during the Spectrum Analysis capture. This object cannot be changed while a capture is in prog… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.8.1.4 | ColumndocsPnmCmtsUsSpecAnSid | read-write | deprecated | This attribute is the SID corresponding to the CM which is granted a burst opportunity for the purpose of Spectrum Analysis. Typically the CMTS will schedule a… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.8.1.5 | ColumndocsPnmCmtsUsSpecAnMiniSlotNum | read-write | deprecated | This attribute provides a mechanism by which the CMTS can begin the Spectrum Analysis at a subcarrier frequency corresponding to the MiniSlotNumber. This attri… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.8.1.6 | ColumndocsPnmCmtsUsSpecAnCmMac | read-write | deprecated | This attribute is used by the CCAP to trigger on a grant for any SID assigned to the CM and to perform the Spectrum Analysis Capture when the burst correspondi… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.8.1.7 | ColumndocsPnmCmtsUsSpecAnCenterFreq | read-write | deprecated | This attribute determines the center frequency of the Spectrum Analysis capture if the trigger mode is FreeRunning. If the trigger mode is not FreeRunning, the… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.8.1.8 | ColumndocsPnmCmtsUsSpecAnSpan | read-write | deprecated | This attribute determines the frequency span of the Spectrum Analysis capture if the trigger mode is FreeRunning. If the trigger mode is not FreeRunning, the C… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.8.1.9 | ColumndocsPnmCmtsUsSpecAnNumberOfBins | read-write | deprecated | This attribute determines the number of bins for the Spectrum Analysis capture if the trigger mode is FreeRunning. If the trigger mode is not FreeRunning, the … |
| 1.3.6.1.4.1.4491.2.1.27.1.3.8.1.10 | ColumndocsPnmCmtsUsSpecAnMeasStatus | read-only | deprecated | This attribute is used to determine the status of the measurement. The PNM server will query this value to determine when the file is ready for transfer. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.8.1.11 | ColumndocsPnmCmtsUsSpecAnFileName | read-write | deprecated | This attribute is the name of the file with the Spectrum Analysis data at the CMTS that is to be downloaded using TFTP to the PNM server. This value can only b… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9 | NodedocsPnmCmtsOptObjects | |||
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.1 | TabledocsPnmCmtsOptReqTable | not-accessible | current | This table is used to initiate the OPT-REQ message for a given OFDM DS channel. The message and resulting tests and requirements are defined in the OPT-REQ TLV… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.1.1 | RowdocsPnmCmtsOptReqEntry | not-accessible | current | The conceptual row of the docsPnmCmtsOptReqTable. The conceptual rows do not persist across device resets. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.1.1.1 | ColumndocsPnmCmtsOptReqCmMacAddr | not-accessible | current | This attribute is a key which represents the MAC address for the referenced CM. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.1.1.2 | ColumndocsPnmCmtsOptReqDsOfdmChanCfgIndex | not-accessible | current | This attribute is a key which represents an instance of the DsOfdmChannelCfg of the Downstream OFDM channel. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.1.1.3 | ColumndocsPnmCmtsOptReqDsOfdmProfCfgId | not-accessible | current | This attribute is a key that is the targeted profile being tested with OPT for the instance of DsOfdmChannelIndex. For Data Profile testing the ID of the profi… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.1.1.4 | ColumndocsPnmCmtsOptReqOpCode | read-create | current | This attribute controls the testing to be performed by the CM receiving the OPT-REQ message. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.1.1.5 | ColumndocsPnmCmtsOptReqProfileTest | read-create | current | This attribute defines which of the OPT tests are to be run by the CM. The tests are encoded as individual bits according to rxMerSubCarrierStats(0) RxMER Stat… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.1.1.6 | ColumndocsPnmCmtsOptReqMaxDuration | read-create | current | This attribute allows the tester to determine how long a test may run before returning results or aborting. This attribute corresponds to TLV 4 in the OPT Requ… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.1.1.7 | ColumndocsPnmCmtsOptReqMaxCodewords | read-create | current | This attribute defines the maximum number of codewords that the CM should examine before the test is complete. When either Nc or more codewords have been recei… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.1.1.8 | ColumndocsPnmCmtsOptReqMaxUncorrectableCws | read-create | current | This attribute defines the max num of uncorrectable codewords the CM should examine before the test is complete. When either Nc or more codewords have been rec… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.1.1.9 | ColumndocsPnmCmtsOptReqCwTaggingEnabled | read-create | current | This attribute indicates whether Codeword Tagging is in use for this test. This attribute is defined as a Boolean with the value 'false' meaning that codeword … |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.1.1.10 | ColumndocsPnmCmtsOptReqNcpFields | read-create | current | This attribute defines the maximum number of NCP fields to be examined during the test. When the CM has examined this number or more NCP fields, it returns the… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.1.1.11 | ColumndocsPnmCmtsOptReqMaxNcpCrcFails | read-create | current | This attribute defines the maximum number of NCP fields that are allowed to fail the NCP CRC checks to be examined during the test. When the CM has examined th… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.1.1.12 | ColumndocsPnmCmtsOptReqStatus | read-create | current | The status of this instance. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.2 | TabledocsPnmCmtsOptMerThreshCfgTable | not-accessible | current | This table is used to configure parameters for RxMER tests defined in docsPnmCmtsOptReqTable that require Pass/Fail criteria. It is necessary to define the par… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.2.1 | RowdocsPnmCmtsOptMerThreshCfgEntry | not-accessible | current | The conceptual row of the docsPnmCmtsOptMerThreshCfgTable. The conceptual rows do not persist across device resets. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.2.1.1 | ColumndocsPnmCmtsOptMerThreshCfgModOrder | not-accessible | current | This attribute is a key which represents the modulation types supported by the CCAP modulator. The value of zeroBitLoaded means that the subcarrier is BPSK mod… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.2.1.2 | ColumndocsPnmCmtsOptMerThreshCfgRxMerVsBitloadingTarget | read-create | current | This attribute is the required value for the profile RxMER (refer to OPT-RSP) in units of 0.25dB (0xFF is 63.75dB). This is the required RxMER value that the C… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.2.1.3 | ColumndocsPnmCmtsOptMerThreshCfgRxMerMargin | read-create | current | The CM reports the number of subcarriers with a measured RxMER value that is at least this value below the target RxMER for the bitloading of the given subcarr… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.2.1.4 | ColumndocsPnmCmtsOptMerThreshCfgStatus | read-create | current | The status of this instance. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.3 | TabledocsPnmCmtsOptProfChgCfgTable | not-accessible | current | This table allows the Operator to force changes in the assigned profiles on a given registered CM. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.3.1 | RowdocsPnmCmtsOptProfChgCfgEntry | not-accessible | current | The conceptual row of the docsPnmCmtsOptProfChgCfgTable. The conceptual rows do not persist across device resets. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.3.1.1 | ColumndocsPnmCmtsOptProfChgCfgIfIndex | not-accessible | current | This attribute is the ifIndex of the DS OFDM channel that the CMTS will instruct the CM to adjust it's profiles for. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.3.1.2 | ColumndocsPnmCmtsOptProfChgCfgDsProfList | read-create | current | This attribute is a list of N 1-byte downstream OFDM profile IDs assigned for the OFDM channel. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.3.1.3 | ColumndocsPnmCmtsOptProfChgCfgStatus | read-create | current | The status of this instance. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.4 | TabledocsPnmCmtsOptRespTable | not-accessible | current | This table is used to read the OPT-RSP message for a given OFDM DS channel. One of the main issues for the modeling for OPT-RSP is that all OPT responses will … |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.4.1 | RowdocsPnmCmtsOptRespEntry | not-accessible | current | The conceptual row of the docsPnmCmtsOptRespTable. The conceptual rows do not persist across device resets. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.4.1.1 | ColumndocsPnmCmtsOptRespStatus | read-only | current | This attribute allows the CCAP to return the status of a specific OPT test request. The value of this attribute is found in the status portion of the OPT-RSP h… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.4.1.2 | ColumndocsPnmCmtsOptRespFirstActiveSubcarrierNum | read-only | current | This attribute is the subcarrier index of the lowest subcarrier in the Occupied Bandwidth of the channel. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.4.1.3 | ColumndocsPnmCmtsOptRespMerData | read-only | current | This attribute contains the MER data for the active subcarriers in the instance of the DsOfdmChannel. The data represents Integer modulation error ratio measur… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.4.1.4 | ColumndocsPnmCmtsOptRespMerPassFailData | read-only | current | This attribute contains a Pass/Fail indication for each subcarrier's RxMER (1 bit for each subcarrier). A value of 1 indicates that the measured MER is greater… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.4.1.5 | ColumndocsPnmCmtsOptRespNumSubcarriersBelowThresh | read-only | current | This attribute indicates the number of subcarriers (less then or equal to 7680) whose RxMER is greater then or equal to the RxMER Margin below the RxMER target… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.4.1.6 | ColumndocsPnmCmtsOptRespSnrMarginData | read-only | current | This attribute indicates the SNR margin of the candidate data profile (signed integer), in units of 0.25dB, calculation is as defined in the PHY3.1 Spec. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.4.1.7 | ColumndocsPnmCmtsOptRespCodewordCt | read-only | current | This attribute is a count of the measured number of codewords that the CM has successfully received during the testing interval for the profile being tested. U… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.4.1.8 | ColumndocsPnmCmtsOptRespCorrectedCodewordCt | read-only | current | This attribute is a count of the measured number of codewords that the CM has successfully received and was able to correct during the testing interval for the… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.4.1.9 | ColumndocsPnmCmtsOptRespUncorrectableCodewordCt | read-only | current | This attribute is a count of the measured num of uncorrectable codewords that the CM has received during the testing interval for the profile being tested. Uns… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.4.1.10 | ColumndocsPnmCmtsOptRespNcpFieldCt | read-only | current | This attribute records the number of NCP fields that were examined by the CM during the test interval. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.9.4.1.11 | ColumndocsPnmCmtsOptRespNcpCrcFailCt | read-only | current | This attribute records the number of NCP fields that failed the NCP CRC check. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10 | NodedocsPnmCmtsUtscObjects | |||
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.1 | TabledocsPnmCmtsUtscCapabTable | not-accessible | current | This table exposes capabilities supported by the CCAP for Upstream Triggered Spectrum Capture trigger modes, data output formats, and windowing function used w… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.1.1 | RowdocsPnmCmtsUtscCapabEntry | not-accessible | current | The conceptual row of the docsPnmCmtsUtscCapabTable. The conceptual rows persist across device resets. A separate entry exists for every Upstream RF Port which… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.1.1.1 | ColumndocsPnmCmtsUtscCapabTriggerMode | read-only | current | This attribute indicates which of the upstream triggered spectrum capture function trigger modes is supported by the CCAP. The attribute is reported in BITS fo… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.1.1.2 | ColumndocsPnmCmtsUtscCapabOutputFormat | read-only | current | This attribute indicates which of the upstream triggered spectrum capture function data output formats are supported by the CCAP. This attribute is reported in… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.1.1.3 | ColumndocsPnmCmtsUtscCapabWindow | read-only | current | This attribute indicates which of the upstream triggered spectrum capture function window formats are supported by the CCAP. This attribute is reported in BITS… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.1.1.4 | ColumndocsPnmCmtsUtscCapabDescription | read-only | current | This attribute reports a textual description of a CCAPs upstream triggered spectrum capture capabilities. The format is vendor-specific. Example content can in… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.2 | TabledocsPnmCmtsUtscCfgTable | not-accessible | current | This table provides configuration functionality for the Upstream Triggered Spectrum Capture function. Refer to the reference for additional details. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.2.1 | RowdocsPnmCmtsUtscCfgEntry | not-accessible | current | The conceptual row of the docsPnmCmtsUtscCfgTable. The conceptual rows does not persist across device resets. A separate entry exists for every Upstream RF Por… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.2.1.1 | ColumndocsPnmCmtsUtscCfgIndex | not-accessible | current | This key attribute is a unique identifier for a particular set of configuration settings. If the CCAP does not support multiple Upstream Triggered Spectrum Sam… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.2.1.2 | ColumndocsPnmCmtsUtscCfgLogicalChIfIndex | read-write | current | This attribute is the interface index of the logical channel to which the sample capture trigger applies, when TriggerMode is miniSlotCount, sid, idleSid, quie… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.2.1.3 | ColumndocsPnmCmtsUtscCfgTriggerMode | read-write | current | This attribute is used to control the trigger mode for the Upstream Triggered Spectrum Analysis sample capture. Values allowed for this attribute are listed an… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.2.1.4 | ColumndocsPnmCmtsUtscCfgMinislotCount | read-write | current | This attribute specifies the minislot number at the beginning of which the CCAP starts the upstream spectrum sample capture. This attribute is applicable only … |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.2.1.5 | ColumndocsPnmCmtsUtscCfgSid | read-write | current | This attribute specifies the SID corresponding to the CM which is granted a burst opportunity for the purpose of Upstream Triggered Spectrum Analysis. This att… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.2.1.6 | ColumndocsPnmCmtsUtscCfgCmMacAddr | read-write | current | This attribute specifies from which cable modem the CCAP will capture upstream transmissions. The CCAP MUST trigger upstream spectrum sample capture on a grant… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.2.1.7 | ColumndocsPnmCmtsUtscCfgTimestamp | read-write | current | This attribute specifies the specific time in the future when upstream spectrum sample capture is required to be initiated. If Enable is true, TriggerMode is s… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.2.1.8 | ColumndocsPnmCmtsUtscCfgCenterFreq | read-write | current | This attribute specifies the center frequency of the upstream spectrum to be sampled for analysis. When this attribute is read, it provides the actual center f… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.2.1.9 | ColumndocsPnmCmtsUtscCfgSpan | read-write | current | This attribute determines the frequency span of the upstream spectrum sample capture. When this attribute is read, it provides the actual span, which may be di… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.2.1.10 | ColumndocsPnmCmtsUtscCfgNumBins | read-write | current | This attribute determines the number of frequency bins or samples per span when sampling the upstream spectrum. When this attribute is read, it provides the ac… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.2.1.11 | ColumndocsPnmCmtsUtscCfgAveraging | read-write | current | This attribute specifies whether the CCAP is to average spectral frequency domain sample power to remove spurious spectral peaks and troughs, and the number of… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.2.1.12 | ColumndocsPnmCmtsUtscCfgFilename | read-write | current | This attribute specifies the name of the file with the upstream triggered spectrum capture data at the CCAP that is to be transferred from the CCAP using TFTP … |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.2.1.13 | ColumndocsPnmCmtsUtscCfgQualifyCenterFreq | read-write | current | This attribute specifies the center frequency of a band that is used to qualify a spectrum for upload. The average of the FFT linear power values in this band … |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.2.1.14 | ColumndocsPnmCmtsUtscCfgQualifyBw | read-write | current | This attribute specifies the bandwidth of a band that is used to qualify a spectrum for upload. The average of the FFT linear power values in this band is comp… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.2.1.15 | ColumndocsPnmCmtsUtscCfgQualifyThrshld | read-write | current | This attribute specifies the threshold applied to qualify a spectrum for upload. The average of the FFT linear power values in the specified band is computed a… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.2.1.16 | ColumndocsPnmCmtsUtscCfgWindow | read-write | current | This attribute specifies the windowing function that will be used when performing the discrete Fourier transform for the upstream spectrum analysis. Use of 'mo… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.2.1.17 | ColumndocsPnmCmtsUtscCfgOutputFormat | read-write | current | This attribute specifies the format of the data returned in the upstream spectrum sample capture file and in the Output attribute of the Results table. The CCA… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.2.1.18 | ColumndocsPnmCmtsUtscCfgRepeatPeriod | read-write | current | This attribute specifies the interval in microseconds between consecutive triggers for FFT sample capture. The CCAP is permitted to trigger at larger intervals… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.2.1.19 | ColumndocsPnmCmtsUtscCfgFreeRunDuration | read-write | current | This attribute specifies the length of time in milliseconds for which the CCAP continues to capture and return FFT results when in free running mode. Sample ca… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.2.1.20 | ColumndocsPnmCmtsUtscCfgTriggerCount | read-write | current | This attribute determines the number of times to trigger upstream spectrum sample capture when Enable and InitiateTest are set to true and configured trigger c… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.2.1.21 | ColumndocsPnmCmtsUtscCfgStatus | read-write | current | The status of this conceptual table row entry. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.3 | TabledocsPnmCmtsUtscCtrlTable | not-accessible | current | This table provides command and control functionality for the Upstream Triggered Spectrum Capture function. Refer to the reference for additional details. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.3.1 | RowdocsPnmCmtsUtscCtrlEntry | not-accessible | current | The conceptual row of the docsPnmCmtsUtscCtrlTable. The conceptual rows does not persist across device resets. A separate entry exists for every Upstream RF Po… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.3.1.1 | ColumndocsPnmCmtsUtscCtrlInitiateTest | read-write | current | This attribute is used to trigger an Upstream Triggered Spectrum Capture. Setting this attribute to true applies all configured upstream triggered spectrum sam… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.4 | TabledocsPnmCmtsUtscStatusTable | not-accessible | current | This table provides functionality for monitoring and reporting status of the Upstream Triggered Spectrum Capture function. Refer to the reference for additiona… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.4.1 | RowdocsPnmCmtsUtscStatusEntry | not-accessible | current | The conceptual row of the docsPnmCmtsUtscStatusTable. The conceptual rows does not persist across device resets. A separate entry exists for every Upstream RF … |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.4.1.1 | ColumndocsPnmCmtsUtscStatusMeasStatus | read-only | current | This attribute is used to report the status of the Upstream Triggered Spectrum Capture. When the value is sampleReady, the CCAP has completed capturing and rec… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.5 | TabledocsPnmCmtsUtscResultTable | not-accessible | current | This table provides functionality for reporting results of the Upstream Triggered Spectrum Capture function. Refer to the reference for additional details. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.5.1 | RowdocsPnmCmtsUtscResultEntry | not-accessible | current | The conceptual row of the docsPnmCmtsUtscResultTable. The conceptual rows does not persist across device resets. A separate entry exists for every Upstream RF … |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.5.1.1 | ColumndocsPnmCmtsUtscResultSampleRate | read-only | current | This attribute reports the FFT sample rate used by the CCAP when sampling the upstream spectrum. The input to the FFT can be the ADC output, the ADC output fol… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.5.1.2 | ColumndocsPnmCmtsUtscResultUsSampleSize | read-only | current | This attribute reports the number of samples collected for FFT. The FFT payload size will be the number of samples multiplied by the number of bytes per sample… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.5.1.3 | ColumndocsPnmCmtsUtscResultSampleTimestamp | read-only | current | This attribute reports the date and time when the FFT sample was recorded. |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.5.1.4 | ColumndocsPnmCmtsUtscResultResolutionBw | read-only | current | This attribute reports the resolution bandwidth used when samples were collected. The resolution bandwidth is the same as the bin spacing for rectangular windo… |
| 1.3.6.1.4.1.4491.2.1.27.1.3.10.5.1.5 | ColumndocsPnmCmtsUtscResultOutput | read-only | current | This attribute returns the upstream spectrum sample capture data in hexadecimal format according to the output format configured in attribute OutputFormat. Ref… |
| 1.3.6.1.4.1.4491.2.1.27.2 | NodedocsPnmMibConformance | |||
| 1.3.6.1.4.1.4491.2.1.27.2.1 | NodedocsPnmMibCompliances | |||
| 1.3.6.1.4.1.4491.2.1.27.2.1.1 | CompliancedocsPnmCmtsCompliance | current | The compliance statement for the CMTS. | |
| 1.3.6.1.4.1.4491.2.1.27.2.1.2 | CompliancedocsPnmCmCompliance | current | The compliance statement for the CM. | |
| 1.3.6.1.4.1.4491.2.1.27.2.1.3 | CompliancedocsPnmCmtsDeprecatedCompliance | deprecated | The compliance statement for deprecated objects. | |
| 1.3.6.1.4.1.4491.2.1.27.2.2 | NodedocsPnmMibGroups | |||
| 1.3.6.1.4.1.4491.2.1.27.2.2.1 | GroupdocsPnmBulkDataGroup | current | Group of objects implemented For Bulk-Data support | |
| 1.3.6.1.4.1.4491.2.1.27.2.2.2 | GroupdocsPnmCmtsGroup | current | Group of objects implemented in the CMTS | |
| 1.3.6.1.4.1.4491.2.1.27.2.2.3 | GroupdocsPnmCmGroup | current | Group of objects implemented in the CM | |
| 1.3.6.1.4.1.4491.2.1.27.2.2.4 | GroupdocsPnmCmtsDeprecatedGroup | deprecated | Deprecated Objects of objects implemented in the CMTS |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| MeasStatusType | INTEGER {other(1), inactive(2), busy(3), sampleReady(4), error(5), resourceUnavailable(6), sampleTruncated(7), interfaceModification(8) } | current | This data type is used to determine the state of a measurement. The enumerated values associated with MeasStatusType are: 'other' Indicates any state not described below. 'inactive' Indicates that a test is not started … |
| ThousandthdB | Integer32 | current | This data type represents power levels that are normally expressed in dB. Units are in thousands of a dB; for example, 5.175 dB will be represented as 5175. |
| UsOfdmaWindowingSizeType | Unsigned32 (0 | 32 | 64 | 96 | 128 | 160 | 192 | 224) | current | This data type is defined to specify the eight possible values for the upstream windowing roll-off period samples. The Roll-Off Period Samples (NRP) are given in number of samples using the sample rate of 102.4 Msamples… |