DOCS-RPHY-MIB
801 objects
This MIB module contains the management objects for the Remote PHY Device (RPD) management. Copyright 2016-2024 Cable Television Laboratories, Inc. All rights reserved.
Imported Objects
| CLAB-DEF-MIB | clabProjDocsis |
| DOCS-IF-MIB | -- RFC 4293 TenthdB TenthdBmV |
| DOCS-IF3-MIB | -- RFC2863 IfDirection docsIf3CmtsCmRegStatusId |
| ENTITY-MIB | PhysicalIndex PhysicalIndexOrZero |
| ENTITY-SENSOR-MIB | -- RFC 6933 EntitySensorDataType EntitySensorDataScale EntitySensorPrecision EntitySensorStatus EntitySensorValue |
| IANA-ENTITY-MIB | -- RFC 6933 IANAPhysicalClass |
| IANAifType-MIB | -- RFC 6933 IANAifType |
| IF-MIB | -- RFC 4546 InterfaceIndex ifIndex |
| INET-ADDRESS-MIB | -- RFC 3411 InetAddressType InetAddress InetAddressPrefixLength InetPortNumber InetVersion |
| IP-MIB | -- RFC 3433 IpAddressOriginTC IpAddressStatusTC Ipv6AddressIfIdentifierTC |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Counter64 Gauge32 Integer32 MODULE-IDENTITY OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | -- RFC 2578 TruthValue DateAndTime MacAddress PhysAddress TEXTUAL-CONVENTION TimeStamp |
| UUID-TC-MIB | -- RFC 4001 UUIDorZero |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.4491.2.1.30 | IdentitydocsRphyMib | This MIB module contains the management objects for the Remote PHY Device (RPD) management. Copyright 2016-2024 Cable Television Laboratories, Inc. All rights … | ||
| 1.3.6.1.4.1.4491.2.1.30.0 | NodedocsRphyNotifications | |||
| 1.3.6.1.4.1.4491.2.1.30.1 | NodedocsRphyObjects | |||
| 1.3.6.1.4.1.4491.2.1.30.1.1 | NodedocsRphyRpdDevMibObjects | |||
| 1.3.6.1.4.1.4491.2.1.30.1.1.1 | TabledocsRphyRpdDevInfoTable | not-accessible | current | This table identifies the RPD for which the details and statistics are being provided. The RpdInfo object is read from the GCP complex TLV Type 100. The attrib… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.1.1 | RowdocsRphyRpdDevInfoEntry | not-accessible | current | The conceptual row of docsRphyRpdDevInfoTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.1.1.1 | ColumndocsRphyRpdDevInfoUniqueId | not-accessible | current | This attribute specifies a globally unique 6-byte identifier for the RPD. By convention, an RPD SHOULD use the MAC address of the lowest numbered Ethernet port… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.1.1.2 | ColumndocsRphyRpdDevInfoSysUpTime | read-only | current | This attribute is the time (in hundredths of a second) since the RPD was last re-initialized. This value is reported by the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.1.1.3 | ColumndocsRphyRpdDevInfoNumCrashFilesAvail | read-only | current | This attribute provides the number of crash files. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.1.1.4 | ColumndocsRphyRpdDevInfoPrincipalCoreStatus | read-only | current | This attribute reports the RPD status with respect to the Principal Core initialization. connected: The RPD is connected to the Principal Core and in the proce… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.2 | TabledocsRphyRpdDevIdentificationTable | not-accessible | current | This table provides data that uniquely identifies the RPD. The Identification TLV Type is 50.19. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.2.1 | RowdocsRphyRpdDevIdentificationEntry | not-accessible | current | The conceptual row of docsRphyRpdDevIdentificationTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.1 | ColumndocsRphyRpdDevIdVendorName | read-only | current | This attribute identifies the RPD manufacturer. The format is vendor proprietary. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.2 | ColumndocsRphyRpdDevIdVendorId | read-only | current | This attribute is the IANA-assigned SMI Network Management Private Enterprise Code of the vendor, as specified in RFC 5612. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.3 | ColumndocsRphyRpdDevIdModelNum | read-only | current | This attribute is the model name and number used by the vendor to identify the RPD. The format is vendor proprietary. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.4 | ColumndocsRphyRpdDevIdSerialNum | read-only | current | This attribute is the serial number of the RPD. The format is vendor proprietary. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.5 | ColumndocsRphyRpdDevIdDeviceAlias | read-only | current | This attribute reports the device name assigned by the operator and represents a 'handle' for the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.6 | ColumndocsRphyRpdDevIdDeviceDescr | read-only | current | This attribute is a short text description of the RPD provided by the RPD manufacturer. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.7 | ColumndocsRphyRpdDevIdHwRev | read-only | current | This attribute is the revision number of the hardware of the RPD. The format is vendor proprietary. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.8 | ColumndocsRphyRpdDevIdCurrSwVer | read-only | current | This attribute is the version number of the software currently running on the RPD. The format is vendor proprietary. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.9 | ColumndocsRphyRpdDevIdBootRomVer | read-only | current | This attribute reports the version number of the boot ROM currently installed on the RPD. The format is vendor proprietary. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.10 | ColumndocsRphyRpdDevIdUsBurstRcvrVendorId | read-only | current | This attribute reports the IANA-assigned SMI Network Management Private Enterprise Code of the RPD's US burst receiver manufacturer, as specified in RFC 5612. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.11 | ColumndocsRphyRpdDevIdUsBurstRcvrModelNum | read-only | current | This attribute reports the model number used by the vendor to identify the RPD's US burst receiver. The format is vendor proprietary. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.12 | ColumndocsRphyRpdDevIdUsBurstRcvrDrivVer | read-only | current | This attribute reports the driver version of the RPD's US burst receiver. The format is vendor proprietary. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.13 | ColumndocsRphyRpdDevIdUsBurstRcvrSerialNum | read-only | current | This attribute reports the serial number of the RPD's US burst receiver. The format is vendor proprietary. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.14 | ColumndocsRphyRpdDevIdRcpProtocolVer | read-only | current | This attribute reports the version of the RCP protocol supported by the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.15 | ColumndocsRphyRpdDevIdRcpSchemaVer | read-only | current | This attribute reports the version of the RCP schema supported by the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.16 | ColumndocsRphyRpdDevIdCurrSwImageLastUpdate | read-only | current | This attribute reports the most recent date and time the software image currently running on the RPD was updated. The RPD preserves the value of this attribute… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.17 | ColumndocsRphyRpdDevIdCurrSwImageName | read-only | current | This attribute reports the name of the software image currently running on the RPD. The RPD preserves the value of this attribute across reboots for a given so… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.18 | ColumndocsRphyRpdDevIdCurrSwImageServerType | read-only | current | This attribute reports the server internet address type of the software image currently running on the RPD. The RPD preserves the value of this attribute acros… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.19 | ColumndocsRphyRpdDevIdCurrSwImageServerAddress | read-only | current | This attribute reports the Internet address of the server from which the software image currently running on the RPD was downloaded. The RPD preserves the valu… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.20 | ColumndocsRphyRpdDevIdCurrSwImageIndex | read-only | current | This attribute reports which software image is currently running on the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.21 | ColumndocsRphyRpdDevIdVspSelector | read-only | current | This attribute contains the Vendor-Specific Pre-configuration (VSP) Selector advertised by the RPD, defined as a human-readable string. This attribute is used … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.3 | TabledocsRphyRpdDevLocationTable | not-accessible | current | This table provides location details for the RPD. The values are populated via a management interface or other automatic mechanisms (e.g. GPS). |
| 1.3.6.1.4.1.4491.2.1.30.1.1.3.1 | RowdocsRphyRpdDevLocationEntry | not-accessible | current | The conceptual row of docsRphyRpdDevLocationTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.3.1.1 | ColumndocsRphyRpdDevLocationDescr | read-only | current | This attribute is short text description of where the RPD has been installed, such as a street address. The format is specific to the operator. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.3.1.2 | ColumndocsRphyRpdDevLocationLatitude | read-only | current | This attribute is the latitudinal coordinate of the RPD location, expressed as a 6-byte long string as described in ISO 6709-2008 (6 digit degrees, minutes, se… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.3.1.3 | ColumndocsRphyRpdDevLocationLongitude | read-only | current | This attribute is the longitudinal coordinate of the RPD location, expressed as a 7-byte long string as described in ISO 6709-2008 (7 digits degrees, minutes, … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.4 | TabledocsRphyRpdDevCoresConnectedTable | not-accessible | current | This table provides a list of CCAP-Cores to which the RPD is authenticated, including the CCAP-Core on which the MIB is polled. For each CCAP-Core instance, th… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.4.1 | RowdocsRphyRpdDevCoresConnectedEntry | not-accessible | current | The conceptual row of docsRphyRpdDevCoresConnectedTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.4.1.1 | ColumndocsRphyRpdDevCoresConnectedIndex | not-accessible | current | This key attribute uniquely identifies an instance of a row in the CoresConnected table. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.4.1.2 | ColumndocsRphyRpdDevCoresConnectedCoreId | read-only | current | This attribute reports the unique identifier, for example a MAC address, of the CCAP Core identified in the row entry. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.4.1.3 | ColumndocsRphyRpdDevCoresConnectedAddressType | read-only | current | This attribute represents the IP address type of the CCAP Core. This value is of type InetAddressType, which is defined by [RFC 4001]. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.4.1.4 | ColumndocsRphyRpdDevCoresConnectedAddress | read-only | current | This attribute provides the IPv4 or IPv6 address of the CCAP-Core. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.4.1.5 | ColumndocsRphyRpdDevCoresConnectedIsPrincipal | read-only | current | This attribute indicates if the CCAP-Core is the principal core. If true, this attribute indicates that this CCAP-Core is the principal core. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.4.1.6 | ColumndocsRphyRpdDevCoresConnectedName | read-only | current | This attribute provides the name of the CCAP-Core as conveyed to the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.4.1.7 | ColumndocsRphyRpdDevCoresConnectedVendorId | read-only | current | This attribute provides the IANA-assigned SMI Network Management Private Enterprise Code of the vendor, as specified in RFC 1700. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.4.1.8 | ColumndocsRphyRpdDevCoresConnectedCoreMode | read-only | current | This attribute indicates the role in which the CCAP core is currently acting for the RPD. It also identifies two intermediate states ('decisionPending' and 'co… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.4.1.9 | ColumndocsRphyRpdDevCoresConnectedInitConfigComplete | read-only | current | This attribute reports whether the Core has indicated that its initial configuration of the RPD is complete. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.4.1.10 | ColumndocsRphyRpdDevCoresConnectedCoreFunction | read-only | current | This attribute reports the operational functions that this Core provides. principal: Core operates as a Principal Core docsis: Core provides DOCSIS services br… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.4.1.11 | ColumndocsRphyRpdDevCoresConnectedAuxCoreGcpConnectionStatus | read-only | deprecated | This attribute reports the status of the GCP connection to the Auxiliary CCAP Core. If the attribute IsPrincipal contains a value of true, this attribute has n… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.4.1.12 | ColumndocsRphyRpdDevCoresConnectedAuxCoreRpdState | read-only | current | This attribute identifies the current operational status with this Auxiliary CCAP Core. If the attribute IsPrincipal contains a value of 'true', this attribute… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.4.1.13 | ColumndocsRphyRpdDevCoresConnectedResourceSetIndex | read-only | current | This attribute reports the resource set index used by the core. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.4.1.14 | ColumndocsRphyRpdDevCoresConnectedGcpBackupConnectionConfig | read-only | current | This attribute reports whether a GCP control connection is maintained to the Core when it is acting as a Backup Core. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.4.1.15 | ColumndocsRphyRpdDevCoresConnectedGcpConnectionStatus | read-only | current | This attribute reports the status of the GCP connection to the Core as seen by the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.4.1.16 | ColumndocsRphyRpdDevCoresConnectedGcpBackupCoreStatus | read-only | current | This attribute reports the operating mode of the Core as seen by the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.4.1.17 | ColumndocsRphyRpdDevCoresConnectedAuthenticationStatus | read-only | current | This attribute reports the authentication status of the selected CCAP Core. other: This value is reported in cases not defined below. authenticated: The RPD is… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5 | TabledocsRphyRpdDevCapabilitiesTable | not-accessible | current | This table provides information about the principal capabilities and constraints of the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1 | RowdocsRphyRpdDevCapabilitiesEntry | not-accessible | current | The conceptual row of docsRphyRpdDevCapabilitiesTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.1 | ColumndocsRphyRpdDevCapabNumDsPorts | read-only | current | This attribute reports the number of Full Spectrum downstream unidirectional RF ports available on a non-Partial Spectrum-capable RPD. A Partial Spectrum-capab… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.2 | ColumndocsRphyRpdDevCapabNumUsPorts | read-only | current | This attribute reports the number of Full Spectrum upstream unidirectional RF ports available on a non-Partial Spectrum-capable RPD. A Partial Spectrum-capable… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.3 | ColumndocsRphyRpdDevCapabNumTenGeNsPorts | read-only | current | This attribute provides the number of 10 Gigabit Ethernet ports supported by the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.4 | ColumndocsRphyRpdDevCapabNumOneGeNsPorts | read-only | current | This attribute provides the number 1 Gigabit Ethernet ports supported by the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.5 | ColumndocsRphyRpdDevCapabNumDsScQamChans | read-only | current | On a non-Partial Spectrum-capable RPD, this attribute reports the number of downstream SC-QAM channels supported per downstream RF port. On a Partial Spectrum-… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.6 | ColumndocsRphyRpdDevCapabNumDsOfdmChans | read-only | current | On a non-Partial Spectrum-capable RPD, this attribute reports the number of downstream OFDM channels supported per downstream RF port. On a Partial Spectrum-ca… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.7 | ColumndocsRphyRpdDevCapabNumUsScQamChans | read-only | current | On a non-Partial Spectrum-capable RPD, this attribute reports the number of upstream SC-QAM channels supported per upstream RF port. On a Partial Spectrum-capa… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.8 | ColumndocsRphyRpdDevCapabNumUsOfdmaChans | read-only | current | On a non-Partial Spectrum-capable RPD, this attribute reports the number of upstream OFDMA channels supported per upstream RF port. On a Partial Spectrum-capab… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.9 | ColumndocsRphyRpdDevCapabNumDsOob55d1Chans | read-only | current | This attribute represents the number of SCTE-55-1 forward (downstream) channels supported on any DS RF port of the RPD. The RPD must report a value of 1 when i… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.10 | ColumndocsRphyRpdDevCapabNumUsOob55d1Chans | read-only | current | On a non-Partial Spectrum-capable RPD, this attribute reports the number of upstream SCTE 55-1 channels supported per upstream RF port. On a Partial Spectrum-c… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.11 | ColumndocsRphyRpdDevCapabNumDsOob55d2Modules | read-only | current | This attribute provides the number of SCTE 55-2 modules supported. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.12 | ColumndocsRphyRpdDevCapabNumUsOob55d2Demods | read-only | current | This attribute provides the number of upstream demodulators per SCTE 55-2 modules supported. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.13 | ColumndocsRphyRpdDevCapabNumNdfChans | read-only | current | On a non-Partial Spectrum-capable RPD, this attribute reports the number of Narrowband Digital Forward (NDF) channels supported per downstream RF port. On a Pa… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.14 | ColumndocsRphyRpdDevCapabNumNdrChans | read-only | current | On a non-Partial Spectrum-capable RPD, this attribute reports the number of Narrowband Digital Return (NDR) channels supported per upstream RF port. On a Parti… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.15 | ColumndocsRphyRpdDevCapabNumDsPspFlowsPerChan | read-only | current | This attribute provides the number of distinct PSP flows supported by the RPD on downstream data pseudowires. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.16 | ColumndocsRphyRpdDevCapabNumUsPspFlowsPerChan | read-only | current | This attribute provides the number of distinct PSP flows supported by the RPD on upstream data pseudowires. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.17 | ColumndocsRphyRpdDevCapabNumAsynchVideoChans | read-only | current | This attribute provides the number of asynchronous MPEG video channels supported per downstream RF port. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.18 | ColumndocsRphyRpdDevCapabNumCwToneGens | read-only | current | This attribute provides the number of CW tone generators supported per downstream RF port. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.19 | ColumndocsRphyRpdDevCapabLowestCwToneFreq | read-only | current | This attribute provides the lowest frequency supported by the CW tone generators. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.20 | ColumndocsRphyRpdDevCapabHighestCwToneFreq | read-only | current | This attribute provides the highest frequency supported by the CW tone generators. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.21 | ColumndocsRphyRpdDevCapabMaxPwrDedCwTone | read-only | current | The attribute allows the RPD to inform the CCAP Core what is the maximum power level relative to the RF Port's BasePower that is supported by its dedicated CW … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.22 | ColumndocsRphyRpdDevCapabQamAsPilot | read-only | current | This attribute indicates if a QAM channel can be configured as a CW tone. A value of true indicates a QAM channel can be configured as a CW tone. A value of fa… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.23 | ColumndocsRphyRpdDevCapabSupportsUdpEncap | read-only | current | This attribute reports whether the RPD supports UDP encapsulation on L2TPv3 pseudowires. A value of true indicates the RPD supports UDP encapsulation on L2TPv3… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.24 | ColumndocsRphyRpdDevCapabSupportsFlowTags | read-only | current | This attribute indicates Flow Tags support capability. If the attribute returns a value of true, the RPD supports Flow Tags on OFDMA channels. A Flow Tag is a … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.25 | ColumndocsRphyRpdDevCapabSupportsFreqTilt | read-only | current | This attribute indicates Frequency Tilt support capability. If the attribute returns a value of true, the RPD supports Frequency Tilt settings on DS RF Ports. … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.26 | ColumndocsRphyRpdDevCapabMaxTiltValue | read-only | current | This attribute indicates the maximum value of tilt settings that the RPD supports. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.27 | ColumndocsRphyRpdDevCapabBufferDepthMonAlertSupp | read-only | current | This attribute indicates buffer depth monitoring alert supported by the RPD. For each bit set to 1, the RPD is capable of monitoring buffer depth on the corres… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.28 | ColumndocsRphyRpdDevCapabBufferDepthCfgSupp | read-only | current | This attribute indicates configuration of the output buffer depth supported by the RPD. This capability is only applicable to DOCSIS downstream channels. For e… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.29 | ColumndocsRphyRpdDevCapabRpdUcdProcTime | read-only | current | This attribute indicates the minimum interval needed by the RPD to process a UCD message received via GCP. This interval is equivalent to CM UCD processing tim… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.30 | ColumndocsRphyRpdDevCapabRpdUcdChgNullGrtTime | read-only | current | This attribute indicates the minimum Null grant interval needed by the RPD in the first MAP with incremented UCD change count. The RPD uses the Null grant in t… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.31 | ColumndocsRphyRpdDevCapabMultiSectionTimingMerRep | read-only | current | This attribute indicates whether the RPD supports Multi-Section Timing and MER reporting as opposed to just reporting a single average Timing and MER. More det… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.32 | ColumndocsRphyRpdDevCapabMinPwrDedCwTone | read-only | current | The object allows the RPD to inform the CCAP Core what is the minimum power level relative to the RF Port's BasePower that is supported by its dedicated CW ton… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.33 | ColumndocsRphyRpdDevCapabMaxPwrQamCwTone | read-only | current | The object allows the RPD to inform the CCAP Core what is the maximum power level setting relative to the RF Port's BasePower that is supported by its QAM chan… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.34 | ColumndocsRphyRpdDevCapabMinPwrQamCwTone | read-only | current | The object allows the RPD to inform the CCAP Core what is the minimum power level setting relative to the RF Port's BasePower that is supported by its QAM chan… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.35 | ColumndocsRphyRpdDevCapabSupportsOpticalNodeRf | read-only | current | This attribute reports whether the RPD supports the RF technology for an optical node. The RPD reports 'false' if it complies with the main section of the [DRF… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.36 | ColumndocsRphyRpdDevCapabMaxDsFrequency | read-only | current | This attribute reports the maximum frequency of any downstream signal that the RPD supports on its DS RF port. This attribute defines the highest frequency of … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.37 | ColumndocsRphyRpdDevCapabMinDsFrequency | read-only | current | This attribute reports the minimum frequency of any downstream signal that the RPD supports on its DS RF port. . This attribute defines the lowest frequency of… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.38 | ColumndocsRphyRpdDevCapabMaxBasePwr | read-only | current | This attribute reports the maximum power level setting that the RPD supports for downstream RF port. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.39 | ColumndocsRphyRpdDevCapabMinTiltValue | read-only | current | This attribute reports the minimum value of the tilt setting that the RPD supports. Note that the RPD can report this value as a negative number. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.40 | ColumndocsRphyRpdDevCapabMinPwrAdjustScQam | read-only | current | This attribute reports the minimum power adjustment value that the RPD supports for downstream SC-QAM channels. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.41 | ColumndocsRphyRpdDevCapabMaxPwrAdjustScQam | read-only | current | This attribute reports the maximum power adjustment that the RPD supports for downstream SC-QAM channel. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.42 | ColumndocsRphyRpdDevCapabMinPwrAdjustOfdm | read-only | current | This attribute reports the minimum power adjustment value that the RPD supports for downstream OFDM channels. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.43 | ColumndocsRphyRpdDevCapabMaxPwrAdjustOfdm | read-only | current | This attribute reports the maximum power adjustment that the RPD supports for downstream OFDM channels. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.44 | ColumndocsRphyRpdDevCapabVspSelector | read-only | deprecated | This attribute contains the Vendor-Specific Pre-configuration (VSP) Selector advertised by the RPD, defined as a human readable string. This attribute is used … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.45 | ColumndocsRphyRpdDevCapabMinBaseUsPowerTarLevel | read-only | current | This attribute reports the minimum value of the base target power reference level for upstream signals received on all upstream channels on an RF port that the… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.46 | ColumndocsRphyRpdDevCapabMaxBaseUsPowerTarLevel | read-only | current | This attribute reports the maximum value of the base target power reference level for upstream signals received on all upstream channels on an RF port that the… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.47 | ColumndocsRphyRpdDevCapabMinTarRxPowerAdjustScqam | read-only | current | This attribute reports the minimum power adjustment to the base target power level that the RPD supports for SC-QAM channels. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.48 | ColumndocsRphyRpdDevCapabMaxTarRxPowerAdjustScqam | read-only | current | This attribute reports the maximum power adjustment to the base target power level that the RPD supports for SC-QAM channels. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.49 | ColumndocsRphyRpdDevCapabMinTarRxPowerAdjustOfdma | read-only | current | This attribute reports the minimum power adjustment to the base target power level that the RPD supports for OFDMA channels. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.50 | ColumndocsRphyRpdDevCapabMaxTarRxPowerAdjustOfdma | read-only | current | This attribute reports the maximum power adjustment to the base target power level that the RPD supports for OFDMA channels. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.51 | ColumndocsRphyRpdDevCapabMinTarRxPowerAdjustNdr | read-only | current | This attribute reports the minimum power adjustment to the base target power level that the RPD supports for NDR channels. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.52 | ColumndocsRphyRpdDevCapabMaxTarRxPowerAdjustNdr | read-only | current | This attribute reports the maximum power adjustment to the base target power level that the RPD supports for NDR channels. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.53 | ColumndocsRphyRpdDevCapabMaxDsPspSegCount | read-only | current | This attribute reports how many PSP segments the RPD can support in a packet received on downstream PSP pseudowires. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.54 | ColumndocsRphyRpdDevCapabDirectDsFlowQueueMapping | read-only | current | This attribute reports whether the RPD supports direct mapping of downstream PSP flows to strict priority queues. [R-DEPI] provides more detailed information a… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.55 | ColumndocsRphyRpdDevCapabDsSchedulerPhbIdList | read-only | current | This attribute reports the list of PHB-IDs supported by the RPDs downstream scheduler. [R-DEPI] provides more detailed information about PHB-IDs for the RPDs d… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.56 | ColumndocsRphyRpdDevCapabRpdPendingEvRepQueueSize | read-only | current | This attribute reports the size of the RPDs Pending Event Report Queue. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.57 | ColumndocsRphyRpdDevCapabRpdLocalEventLogSize | read-only | current | This attribute reports the size of the RPDs Local Event Log. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.58 | ColumndocsRphyRpdDevCapabSupportsUsProfileQuery | read-only | current | This attribute reports whether the RPD supports UsScQamProfileQuery (TLV 150) and UsOfdmaConfigQuery (TLV 151) via UsScQamProfileResponse (TLV 152) and UsOfdma… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.59 | ColumndocsRphyRpdDevCapabSupportsFlowTagIncrement | read-only | current | This attribute reports whether the RPD supports the FlowTagIncrement TLV. The RPD reports a value of 'false' when it does not support the FlowTagIncrement TLV … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.60 | ColumndocsRphyRpdDevCapabMinBasePwr | read-only | current | This attribute reports the minimum power level setting that the RPD supports for a downstream RF port. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.61 | ColumndocsRphyRpdDevCapabNumCoresSupported | read-only | current | This attribute reports the number of Cores supported by the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.62 | ColumndocsRphyRpdDevCapabMaxDsOob55d1Frequency | read-only | current | This attribute reports the highest center frequency on which an SCTE 55-1 forward channel can be modulated in Hertz. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.63 | ColumndocsRphyRpdDevCapabSupportsDsOob55d2SecFreq | read-only | current | This attribute indicates whether the RPD supports modulating the SCTE-55-2 forward (downstream) channel on two frequencies per DS RF port. The RPD reports a va… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.64 | ColumndocsRphyRpdDevCapabMaxDsOob55d2Frequency | read-only | current | This attribute reports the highest center frequency on which an SCTE 55-2 forward channel can be modulated in Hertz. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.65 | ColumndocsRphyRpdDevCapabReportsOfdmConfigChangeCounts | read-only | current | This attribute reports the implementation of TLVs to report the configuration change counts of OFDM channels, namely OcdConfigChangeCount and DpdConfigChangeCo… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.6 | TabledocsRphyRpdDevChanReachabilityTable | not-accessible | current | This table provides RPD channel reachability constraints. In some RPD implementations, an Ethernet interface might not have connectivity to all channels on a p… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.6.1 | RowdocsRphyRpdDevChanReachabilityEntry | not-accessible | current | The conceptual row of docsRphyRpdDevChanReachabilityTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.6.1.1 | ColumndocsRphyRpdDevChanReachabilityEnetPortIndex | not-accessible | current | This attribute identifies the Ethernet port on the RPD that has the connectivity constraint. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.6.1.2 | ColumndocsRphyRpdDevChanReachabilityRfPortIndex | not-accessible | current | This attribute identifies the RF port with which the Ethernet port has a connectivity constraint. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.6.1.3 | ColumndocsRphyRpdDevChanReachabilityChanType | not-accessible | current | This attribute identifies the type of channel that is supported within the specified channel index range on this RF port from the specified Ethernet interface.… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.6.1.4 | ColumndocsRphyRpdDevChanReachabilityStartChanIndex | not-accessible | current | This attribute identifies the first channel of the specified channel type in the range of channels that does not have connectivity to the specified Ethernet po… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.6.1.5 | ColumndocsRphyRpdDevChanReachabilityEndChanIndex | read-only | current | This attribute identifies the last channel of the specified channel type in the range of channels that does not have connectivity to the specified Ethernet por… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.7 | TabledocsRphyRpdDevDsUsRfPortAllocTable | not-accessible | current | This table provides the allocation status for the downstream channel resources on the RPD on a per DS RF port basis as well as for the upstream channel resourc… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.7.1 | RowdocsRphyRpdDevDsUsRfPortAllocEntry | not-accessible | current | The conceptual row of docsRphyRpdDevDsUsRfPortAllocTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.7.1.1 | ColumndocsRphyRpdDevDsUsRfPortAllocIndex | not-accessible | current | This attribute provides the index of the downstream or upstream RF port for which resource allocation is being reported. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.7.1.2 | ColumndocsRphyRpdDevDsUsRfPortAllocDirection | not-accessible | current | This attribute indicates whether the allocation applies to the upstream or downstream RF Port. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.7.1.3 | ColumndocsRphyRpdDevDsUsRfPortAllocScQamChans | read-only | current | This attribute provides the number of allocated SC-QAM channels on this RF port. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.7.1.4 | ColumndocsRphyRpdDevDsUsRfPortAllocOfdmChans | read-only | current | This attribute provides the number of allocated DOCSIS 3.1 channels on this RF port. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.7.1.5 | ColumndocsRphyRpdDevDsUsRfPortAllocOob551Chans | read-only | current | This attribute provides the number of allocated SCTE 55-1 channels on this RF port. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.7.1.6 | ColumndocsRphyRpdDevDsUsRfPortAllocNdChans | read-only | current | This attribute provides the number of allocated narrowband digital forward channels (for DS RF Ports) or narrowband digital return channels (for US RF Ports) o… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.7.1.7 | ColumndocsRphyRpdDevDsUsRfPortAllocBdrs | read-only | current | This attribute reports how many BDRs have been allocated on the RPD. This attribute is not applicable for US channels and always reports zero. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.7.1.8 | ColumndocsRphyRpdDevDsUsRfPortAllocConfiguredBcgs | read-only | current | This attribute reports how many BCGs have been configured on the RPD. This attribute is not applicable for US channels and always reports zero. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.8 | TabledocsRphyRpdDevL2tpSessionInfoTable | not-accessible | current | This table provides details about each tunnel session between the RPD and each CCAP Core with which the RPD is associated from the RPD's point of view. It is b… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.8.1 | RowdocsRphyRpdDevL2tpSessionInfoEntry | not-accessible | current | The conceptual row of docsRphyRpdDevL2tpSessionInfoTable. A row entry is created for every session the RPD terminates and there may be entries for sessions wit… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.1 | ColumndocsRphyRpdDevL2tpSessionInfoSessionIpAddrType | not-accessible | current | This key attribute indicates whether the IP address provided in the CcapLcceIpAddress and RpdLcceIpAddr attributes are IPv4 or IPv6. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.2 | ColumndocsRphyRpdDevL2tpSessionInfoCcapLcceIpAddr | not-accessible | current | This key attribute provides the LCCE IP address on the CCAP Core of the session detailed in the instance. As reported by the RPD for a static multicast session… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.3 | ColumndocsRphyRpdDevL2tpSessionInfoRpdLcceIpAddr | not-accessible | current | This key attribute reports the remote-side RPD LCCE IP address of the session detailed in the instance. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.4 | ColumndocsRphyRpdDevL2tpSessionInfoDirection | not-accessible | current | This key attribute reports the direction of the session detailed in the instance. Valid values include: 'forward' - Forward (downstream) direction toward the R… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.5 | ColumndocsRphyRpdDevL2tpSessionInfoL2tpSessionId | not-accessible | current | This key attribute reports the value of the L2TPv3 session ID transmitted or received on the session. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.6 | ColumndocsRphyRpdDevL2tpSessionInfoCoreId | read-only | current | This attribute reports the unique identifier, for example a MAC address, of the CCAP Core with which this session terminates. The CCAP Core sends its unique id… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.7 | ColumndocsRphyRpdDevL2tpSessionInfoConnCtrlID | read-only | current | This attribute indicates the control connection identifier (CCID) for this session. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.8 | ColumndocsRphyRpdDevL2tpSessionInfoUdpPort | read-only | current | This attribute provides the UDP Port reported by the RPD when the DEPI session uses L2TPv3 Header Over UDP. This attribute reports a value of 0 when the sessio… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.9 | ColumndocsRphyRpdDevL2tpSessionInfoDescr | read-only | current | This attribute provides an ASCII string constructed with the form: RemoteEndId=(pp:mmm:ccc), ... { repeated for multiple endpoints } where pp is the 0-based po… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.10 | ColumndocsRphyRpdDevL2tpSessionInfoSessionType | read-only | current | This attribute specifies whether the session is an MPT session or PSP session. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.11 | ColumndocsRphyRpdDevL2tpSessionInfoSessionSubType | read-only | current | This attribute specifies the type of DEPI MPT or DEPI PSP session. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.12 | ColumndocsRphyRpdDevL2tpSessionInfoMaxPayload | read-only | current | This attribute indicates the maximum MTU negotiated between the CCAP Core and the RPD during the session establishment process. It considers the header subtrac… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.13 | ColumndocsRphyRpdDevL2tpSessionInfoPathPayload | read-only | current | This attribute indicates the maximum MTU traversing the CIN from CCAP Core to the RPD. This is calculated by the CCAP Core by procedures such as MTU discovery … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.14 | ColumndocsRphyRpdDevL2tpSessionInfoRpdIfMtu | read-only | current | This attribute provides the RPD's CIN interface MTU and is read as the value of the following L2TPV3 AVP transmitted by the RPD during session setup: DEPI Down… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.15 | ColumndocsRphyRpdDevL2tpSessionInfoCoreIfMtu | read-only | current | This attribute provides the CCAP Core's CIN interface MTU and is read as the value of the following L2TPv3 AVP as received by the device during session setup: … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.16 | ColumndocsRphyRpdDevL2tpSessionInfoErrorCode | read-only | current | The error code raised when the session is in an error state: 'invalidMACInterfaceValue' Indicates wrong assignment of the CCAP Core MAC interface ifIndex. 'inv… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.17 | ColumndocsRphyRpdDevL2tpSessionInfoCreationTime | read-only | current | The attribute contains the sysUptime when the entry was turned active. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.18 | ColumndocsRphyRpdDevL2tpSessionInfoOperStatus | read-only | current | This attribute provides the current status of the pseudowire from the point of view of the specific reporting entity (RPD).For static psuedowires, the only val… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.19 | ColumndocsRphyRpdDevL2tpSessionInfoLocalStatus | read-only | current | The attribute provides the status of the pseudowire in the local node. If the 'other' bit is set, it indicates that an additional vendor-specific status is rep… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.20 | ColumndocsRphyRpdDevL2tpSessionInfoLastChange | read-only | current | The attribute provides the value of sysUpTime when the session entered its current OperStatus state from the point of view of the specific reporting entity (RP… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.21 | ColumndocsRphyRpdDevL2tpSessionInfoExtendedRemoteEndId | read-only | current | This attribute provides an ASCII string constructed with the form: RemoteEndId=(pp:mmm:ccc),... { repeated for multiple channels } where pp is the zero-based p… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.9 | TabledocsRphyRpdDevL2tpSessionStatsTable | not-accessible | current | This table provides statistics about each tunnel session between the RPD and each CCAP Core with which the RPD is associated from the RPD's point of view. The … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.9.1 | RowdocsRphyRpdDevL2tpSessionStatsEntry | not-accessible | current | The conceptual row of docsRphyRpdDevL2tpSessionStatsTable. This table is an augmentation of docsRphyL2tpSessionInfoTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.9.1.1 | ColumndocsRphyRpdDevL2tpSessionStatsOutOfSeqPkts | read-only | current | This attribute indicates the count of session packets that were received out of sequence from the point of view of the reporting entity. It is vendor dependent… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.9.1.2 | ColumndocsRphyRpdDevL2tpSessionStatsInPkts | read-only | current | This attribute counts the number of received packets accepted for processing above the L2TPv3 protocol layer. The InPackets attribute count excludes packets dr… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.9.1.3 | ColumndocsRphyRpdDevL2tpSessionStatsInDiscards | read-only | current | This attribute counts the number of received packets discarded by the L2TPv3 protocol layer itself, including those discarded because they were out of sequence… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.9.1.4 | ColumndocsRphyRpdDevL2tpSessionStatsOutPkts | read-only | current | This attribute counts the number of packets conceptually attempted to be transmitted from above the L2TPv3 protocol layer. The OutPackets attribute counts pack… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.9.1.5 | ColumndocsRphyRpdDevL2tpSessionStatsOutErrors | read-only | current | This attribute counts the number of packets attempted to be transmitted from above the L2TPv3 protocol layer that could not be transmitted below the L2TPv3 pro… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.9.1.6 | ColumndocsRphyRpdDevL2tpSessionStatsCounterDiscontinuityTime | read-only | current | This attribute reports the date and time at which any one or more of the counters in this group were created or last reset to zero. If the RPD does not acquire… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.10 | TabledocsRphyRpdDevDiagStatusTable | not-accessible | current | This table reports information about an RPD's diagnostic self test results. The CCAP Core reads DiagnosticStatus attributes with GCP complex TLV Type 100.4. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.10.1 | RowdocsRphyRpdDevDiagStatusEntry | not-accessible | current | The conceptual row of docsRphyRpdDevDiagStatusTable. This table returns at least one row indicating pass or failure for the diagnostic self test. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.10.1.1 | ColumndocsRphyRpdDevDiagStatusProbableCause | read-only | current | This attribute reports the probable cause of the diagnostic test error condition. Probable causes may be related to: - Communications error - Quality of Servic… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.10.1.2 | ColumndocsRphyRpdDevDiagStatusAdditionalText | read-only | current | This attribute reports a free form text description of the diagnostic test error condition. This provides supplemental information for the ProbableCause. When … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.10.1.3 | ColumndocsRphyRpdDevDiagStatusSeverityLevel | read-only | current | This attribute reports the severity level for the diagnostic test error condition. Severity levels are based on the DOCSIS event priority levels. When the self… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.11 | TabledocsRphyRpdDevDepiMcastSessionTable | not-accessible | current | This table reports the DEPI IP multicast sessions currently joined by an RPD. The CCAP Core reads DepiMcastSession attributes with GCP complex TLV Type 100.5. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.11.1 | RowdocsRphyRpdDevDepiMcastSessionEntry | not-accessible | current | The conceptual row of docsRphyRpdDevDepiMcastSessionTable. A row entry of this table represents one DEPI IP Multicast session replicated to one RPD. The indexi… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.11.1.1 | ColumndocsRphyRpdDevDepiMcastSessionIpAddrType | not-accessible | current | This key attribute reports whether the IP addresses provided in GrpIpAddr, SrcIpAddr, RpdLcceIpAddr and CcapLcceIpAddr are IPv4 or IPv6. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.11.1.2 | ColumndocsRphyRpdDevDepiMcastSessionGrpIpAddr | not-accessible | current | This key attribute reports the group (destination) address of an IP multicast session transmitted via DEPI multicast. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.11.1.3 | ColumndocsRphyRpdDevDepiMcastSessionSrcIpAddr | not-accessible | current | For Source Specific Multicast (SSM), this key attribute reports the source IP address of an IP multicast session transmitted via DEPI multicast. For Any-Source… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.11.1.4 | ColumndocsRphyRpdDevDepiMcastSessionL2tpSessionId | not-accessible | current | This attribute reports the L2TPv3 Session ID assigned by the CCAP Core to the DEPI IP multicast session. The value is assigned according to the referenced spec… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.11.1.5 | ColumndocsRphyRpdDevDepiMcastSessionRpdLcceIpAddr | read-only | current | This attribute reports the RPD local LCCE IP address of the L2TPv3 DEPI control session that instructed the RPD to join the IP multicast session. In the case o… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.11.1.6 | ColumndocsRphyRpdDevDepiMcastSessionCcapLcceIpAddr | read-only | current | This attribute reports the RPD remote LCCE IP address (i.e. on the CCAP Core) of the L2TPv3 control session that instructed the RPD to join the IP multicast se… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.11.1.7 | ColumndocsRphyRpdDevDepiMcastSessionJoinTime | read-only | current | This attribute reports the last time the RPD has joined this session. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.12 | TabledocsRphyRpdDevEventLogTable | not-accessible | current | This table reports event log information for an RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.12.1 | RowdocsRphyRpdDevEventLogEntry | not-accessible | current | The conceptual row of docsRphyRpdDevEventLogTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.12.1.1 | ColumndocsRphyRpdDevEventLogIndex | not-accessible | current | This key attribute provides relative ordering of the events in the event log. This attribute will always increase except when (a) the log is reset (b) the devi… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.12.1.2 | ColumndocsRphyRpdDevEventLogFirstTime | read-only | current | This attribute provides the local RPD time when this event was created. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.12.1.3 | ColumndocsRphyRpdDevEventLogLastTime | read-only | current | When an event reports only one event occurrence, this attribute will have the same value as the corresponding instance of FirstTime. When an event reports mult… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.12.1.4 | ColumndocsRphyRpdDevEventLogCounts | read-only | current | This attribute provides the number of consecutive event occurrences reported by this event. This starts at 1 with the creation of this event occurrence and inc… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.12.1.5 | ColumndocsRphyRpdDevEventLogLevel | read-only | current | This attribute provides the priority level of this event, as defined by Annex B. These are ordered from most serious (emergency) to least serious (debug). |
| 1.3.6.1.4.1.4491.2.1.30.1.1.12.1.6 | ColumndocsRphyRpdDevEventLogId | read-only | current | This attribute provides the identifier of this event, as defined by Annex B. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.12.1.7 | ColumndocsRphyRpdDevEventLogText | read-only | current | This attribute provides the message text of this event, as defined by Annex B. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.13 | TabledocsRphyRpdDevOob551UsChanStatusTable | not-accessible | current | This table provides per-RPD counts of upstream SCTE 55-1 cells sent to a Network Controller. These counts are updated by the CCAP Core, which parses each upstr… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.13.1 | RowdocsRphyRpdDevOob551UsChanStatusEntry | not-accessible | current | The conceptual row of docsRphyRpdDevOob551UsChanStatusTable. A row entry of this table represents counts that are updated by the CCAP Core, which parses each u… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.1 | ColumndocsRphyRpdDevOob551UsChanStatusRfPort | not-accessible | current | This key attribute reports the RPD RF virtual port number carrying this SCTE 55-1 US channel. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.2 | ColumndocsRphyRpdDevOob551UsChanStatusChannelId | not-accessible | current | This key attribute reports the virtual demodulator ID (channel number) for this SCTE 55-1 US channel. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.3 | ColumndocsRphyRpdDevOob551UsChanStatusNcIpAddrType | read-only | current | This attribute indicates whether the IP address provide in docsRphyRpdDevOob551UsChanStatusNcIpAddr is IPv4 or IPv6. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.4 | ColumndocsRphyRpdDevOob551UsChanStatusNcIpAddr | read-only | current | This attribute reports the IP host address of the Network Controller receiving the cells on this SCTE 55-1 US channel. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.5 | ColumndocsRphyRpdDevOob551UsChanStatusArpdSrcIpAddrType | read-only | current | This attribute indicates whether the IP address provide in docsRphyRpdDevOob551UsChanStatusArpdSrcIpAddr is IPv4 or IPv6. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.6 | ColumndocsRphyRpdDevOob551UsChanStatusArpdSrcIpAddr | read-only | current | This attribute reports the virtual ARPD source IP host address used when sending cells to the Network Controller. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.7 | ColumndocsRphyRpdDevOob551UsChanStatusPerfectCellsRcvd | read-only | current | This attribute reports the number of perfect cells received by the demodulator for this SCTE 55-1 US channel. Perfect cells have status 0 in the US SCTE 55-1 O… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.8 | ColumndocsRphyRpdDevOob551UsChanStatusCorrectedCellsRcvd | read-only | current | This attribute reports the number of errored cells received by the demodulator for this SCTE 55-1 US channel that were successfully corrected. Corrected cells … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.9 | ColumndocsRphyRpdDevOob551UsChanStatusUncorrectableCellsRcvd | read-only | current | This attribute reports the number of errored cells received by the demodulator for this SCTE 55-1 US channel that could not be corrected. Uncorrectable cells h… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.10 | ColumndocsRphyRpdDevOob551UsChanStatusTotalCellsRcvd | read-only | current | This attribute reports the total of all cells received for this SCTE 55-1 US channel. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.11 | ColumndocsRphyRpdDevOob551UsChanStatusPwrLevel | read-only | current | This attribute reports the arithmetic mean power level from nominal of all received MAC Cells by the demodulator for this upstream SCTE 55-1 channel with preci… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.12 | ColumndocsRphyRpdDevOob551UsChanStatusMaxPwrLevel | read-only | current | This attribute reports the maximum power level from nominal of all received MAC Cells by the demodulator for this upstream SCTE 55-1 channel with precision of … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.13 | ColumndocsRphyRpdDevOob551UsChanStatusMinPwrLevel | read-only | current | This attribute reports the minimum power level from nominal of all received MAC Cells by the demodulator for this upstream SCTE 55-1 channel with precision of … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.14 | ColumndocsRphyRpdDevOob551UsChanStatusCounterDiscontinuityTime | read-only | current | This attribute reports the date and time at which any one or more of the counters in this group were created or last reset to zero. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.15 | ColumndocsRphyRpdDevOob551UsChanStatusOperStatus | read-only | current | This attribute reports the operational status of the selected channel. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.14 | TabledocsRphyRpdDevCrashDataFileStatusTable | not-accessible | current | This table provides status information for the crash analysis data files. The RPD must generate a crash analysis file when it encounters an unrecoverable softw… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.14.1 | RowdocsRphyRpdDevCrashDataFileStatusEntry | not-accessible | current | The conceptual row of docsRphyRpdDevCrashDataFileStatusTable. A row entry of this table represents a file that is available in the device for upload or for whi… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.14.1.1 | ColumndocsRphyRpdDevCrashDataFileStatusIndex | not-accessible | current | This key attribute uniquely identifies a crash analysis file. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.14.1.2 | ColumndocsRphyRpdDevCrashDataFileStatusFilename | read-only | current | This attribute contains the name of the crash analysis file, stored in the device that is available to be uploaded to the server. Filenames are defined by the … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.14.1.3 | ColumndocsRphyRpdDevCrashDataFileStatusFileStatus | read-only | current | This attribute reflects the status of the crash data file. The possible values are listed below. other(1) - Any condition not covered by the other defined valu… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.15 | TabledocsRphyRpdDevUsSignalQualityTable | not-accessible | current | This table provide individual upstream signal quality values for RPDs. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.15.1 | RowdocsRphyRpdDevUsSignalQualityEntry | not-accessible | current | The conceptual row of docsRphyRpdDevUsSignalQualityTable. A row entry of this table represents the upstream signal quality values of a single RPD |
| 1.3.6.1.4.1.4491.2.1.30.1.1.15.1.1 | ColumndocsRphyRpdDevUsSignalQualityRfPort | not-accessible | current | This key attribute reports the RPD RF port number carrying this US channel. This corresponds to the attribute RpdUsRfPortNum of the RpdUsRfPortRef object in th… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.15.1.2 | ColumndocsRphyRpdDevUsSignalQualityChannelIfIndex | not-accessible | current | This attribute corresponds to the ifIndex of the logical upstream channel (ifType docsCableUpstreamChannel(205)) of the CCAP Core for this US channel. Note tha… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.15.1.3 | ColumndocsRphyRpdDevUsSignalQualityRxMer | read-only | current | This attribute reports an in-channel received average Modulation Error Ratio (MER). An RxMER sample is defined as an estimate, provided by the demodulator, of … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.15.1.4 | ColumndocsRphyRpdDevUsSignalQualityRxMerSamples | read-only | current | This attribute reports RxMerSamples which is a statistically significant number of bursts for the CCAP Core, processed to arrive at the RxMER value. For the CC… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.15.1.5 | ColumndocsRphyRpdDevUsSignalQualityUnerroreds | read-only | current | This attribute reports the count of codewords received on this channel without error. This includes all codewords, whether or not they were part of frames dest… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.15.1.6 | ColumndocsRphyRpdDevUsSignalQualityCorrecteds | read-only | current | This attribute reports the count of codewords received on this channel with correctable errors. This includes all codewords, whether or not they were part of f… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.15.1.7 | ColumndocsRphyRpdDevUsSignalQualityUncorrectables | read-only | current | This attribute reports the count of codewords received on this channel with uncorrectable errors. This includes all codewords, whether or not they were part of… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.16 | TabledocsRphyRpdDevHostResSysTable | not-accessible | current | This object is the container for RPD system attributes. The HostResourcesSystem TLV Type is 100.21. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.16.1 | RowdocsRphyRpdDevHostResSysEntry | not-accessible | current | The conceptual row of docsRphyRpdDevHostResSysTable. A row entry of this table represents the details and statistics of the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.16.1.1 | ColumndocsRphyRpdDevHostResSysDate | read-only | current | This attribute reports the RPD's notion of the current local date and time of day. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.17 | TabledocsRphyRpdDevHostResStorTable | not-accessible | current | This table reports information about logical storage areas on the host at the time when the values are read. An entry is associated with each logical storage a… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.17.1 | RowdocsRphyRpdDevHostResStorEntry | not-accessible | current | The conceptual row of docsRphyRpdDevHostResStorTable. A row entry of this table represents a logical storage area on the host. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.17.1.1 | ColumndocsRphyRpdDevHostResStorIndex | not-accessible | current | A unique value for each logical storage area contained by the host. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.17.1.2 | ColumndocsRphyRpdDevHostResStorType | read-only | current | This attribute contains the type of storage represented by this object. The following storage types are supported: other: The storage type identifier used when… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.17.1.3 | ColumndocsRphyRpdDevHostResStorAllocationUnits | read-only | current | The size, in bytes, of the data objects allocated from this pool. If this entry is monitoring sectors, blocks, buffers, or packets, for example, this number wi… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.17.1.4 | ColumndocsRphyRpdDevHostResStorAllocationFailures | read-only | current | The number of requests for storage represented by this entry that could not be honored due to not enough storage. It should be noted that as this object has a … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.17.1.5 | ColumndocsRphyRpdDevHostResStorSize | read-write | current | The size of the storage represented by this entry, in units of Storage Allocation Units. This object is writable to allow remote configuration of the size of t… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.17.1.6 | ColumndocsRphyRpdDevHostResStorUsed | read-only | current | The amount of the storage represented by this entry that is allocated, in units of Storage Allocation Units |
| 1.3.6.1.4.1.4491.2.1.30.1.1.17.1.7 | ColumndocsRphyRpdDevHostResStorDescr | read-only | current | A description of the type and instance of the storage described by this entry. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.18 | TabledocsRphyRpdDevHostResSwRunTable | not-accessible | current | Entries in this table represent each distinct process (i.e., piece of software) that is running or loaded into physical or virtual memory in preparation for ru… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.18.1 | RowdocsRphyRpdDevHostResSwRunEntry | not-accessible | current | The (conceptual) entry for one piece of software running on the host. Note that because the installed software table only contains information for software sto… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.18.1.1 | ColumndocsRphyRpdDevHostResSwRunIndex | not-accessible | current | A unique value for each piece of software running on the host. Wherever possible, this should be the system's native, unique identification number. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.18.1.2 | ColumndocsRphyRpdDevHostResSwRunType | read-only | current | This attribute contains the type of the software piece running on the host. Valid values are listed below: unknown(1) if the software type is unknown or is not… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.18.1.3 | ColumndocsRphyRpdDevHostResSwRunStatus | read-only | current | The status of this running piece of software. Setting this value to invalid(4) shall cause this software to stop running and to be unloaded. Sets to other valu… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.18.1.4 | ColumndocsRphyRpdDevHostResSwRunPerfCpu | read-only | current | The number of centi-seconds of the total system's CPU resources consumed by this process. Note that on a multi-processor system, this value may increment by mo… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.18.1.5 | ColumndocsRphyRpdDevHostResSwRunPerfMem | read-only | current | The total amount of real system memory allocated to this process. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.18.1.6 | ColumndocsRphyRpdDevHostResSwRunName | read-only | current | A textual description of this running piece of software, including the manufacturer, revision, and the name by which it is commonly known. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.19 | TabledocsRphyRpdDevStaticPwCapTable | not-accessible | current | This table provides information about the static pseudo-wire capabilities of the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.19.1 | RowdocsRphyRpdDevStaticPwCapEntry | not-accessible | current | The conceptual row of docsRphyRpdDevStaticPwCapTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.19.1.1 | ColumndocsRphyRpdDevStaticPwCapMaxFwdStaticPws | read-only | current | This attribute reports the maximum number of (multicast and unicast) forward static pseudowires supported by the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.19.1.2 | ColumndocsRphyRpdDevStaticPwCapMaxRetStaticPws | read-only | current | This attribute reports the maximum number of return static pseudowires supported by the RPD. An RPD which does not support return static pseudowires reports ze… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.19.1.3 | ColumndocsRphyRpdDevStaticPwCapSupportsStaticMptDepiPw | read-only | current | This attribute reports whether the RPD supports configuration of static pseudowires of DEPI MPT (MPT-DEPI-PW) subtype. The RPD reports a value of false(0) if i… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.19.1.4 | ColumndocsRphyRpdDevStaticPwCapSupportsStaticMpt55d1RetPw | read-only | current | This attribute reports whether the RPD supports configuration of static pseudowires of SCTE 55-1 return (MPT-55-1-RET) subtype. The RPD reports a value of fals… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.19.1.5 | ColumndocsRphyRpdDevStaticPwCapSupportsStaticPspNdfPw | read-only | current | This attribute reports whether the RPD supports configuration of multicast static pseudowires of PSP NDF (PSP-NDF) subtype. The RPD reports a value of false(0)… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.19.1.6 | ColumndocsRphyRpdDevStaticPwCapSupportsStaticPspNdrPw | read-only | current | This attribute reports whether the RPD supports configuration of static pseudowires of PSP NDR (PSP-NDR) subtype. The RPD reports a value of false(0) if it doe… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.19.1.7 | ColumndocsRphyRpdDevStaticPwCapMaxUcastFwdStaticPws | read-only | current | This attribute is used to report the maximum number of unicast forward static pseudowires supported by the RPD. An RPD which does not support unicast forward s… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.19.1.8 | ColumndocsRphyRpdDevStaticPwCapSupportsStaticPspNdfUcastPw | read-only | current | This attribute reports whether the RPD supports configuration of unicast forward static pseudowires of PSP NDF (PSP-NDF) subtype. The RPD reports a value of fa… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.19.1.9 | ColumndocsRphyRpdDevStaticPwCapSupportsStaticPspPnmPw | read-only | current | This attribute reports whether the RPD supports configuration of static pseudowires of PSP-PNM subtype. The RPD reports a value of false(0) if it does not supp… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.19.1.10 | ColumndocsRphyRpdDevStaticPwCapSupportsStaticPspSpecmanPw | read-only | current | This attribute reports whether the RPD supports configuration of static pseudowires of PSP-SPECMAN subtype. The RPD reports a value of false(0) if it does not … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.19.1.11 | ColumndocsRphyRpdDevStaticPwCapSupportsDepiPspMultichanPw | read-only | current | This attribute reports whether the RPD supports configuration of static pseudowires of subtype PSP-MULTICHAN-PW. The RPD reports a value of false(0) if is does… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.19.1.12 | ColumndocsRphyRpdDevStaticPwCapSupportsUepiPws | read-only | current | This attribute reports whether the RPD supports configuration of UEPI static pseudowires. A single capability indicates support for the pseudowire subtypes lis… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.19.1.13 | ColumndocsRphyRpdDevStaticPwCapSupportsDtpPw | read-only | current | This attribute reports whether the RPD supports configuration of static pseudowires for DOCSIS Time Protocol (DTP) operation. The RPD reports a value of false(… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.20 | TabledocsRphyRpdDevExtSwImageSupportTable | not-accessible | current | This object provides information about the Main Software Image and the additional optional software images that can be maintained by the RPD. The ExtSwImageSup… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.20.1 | RowdocsRphyRpdDevExtSwImageSupportEntry | not-accessible | current | The conceptual row of docsRphyRpdDevExtSwImageSupportTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.20.1.1 | ColumndocsRphyRpdDevExtSwImageSupportSwImageIndex | not-accessible | current | This key attribute is used in selecting a software image maintained by the RPD. The value of zero is reseved for the Main Software Image. The maximum value of … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.20.1.2 | ColumndocsRphyRpdDevExtSwImageSupportSwImageLastUpdate | read-only | current | This attribute reports the most recent date and time when the selected RPD's software image was updated. The RPD preserves the value of this attribute across r… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.20.1.3 | ColumndocsRphyRpdDevExtSwImageSupportSwImageName | read-only | current | This attribute reports the name of the RPD's software image. The RPD preserves the value of this attribute across reboots. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.20.1.4 | ColumndocsRphyRpdDevExtSwImageSupportSwImageDescr | read-only | current | This attribute reports human readable description of the SW image running at the selected index. For example it can report that the that selected index points … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.20.1.5 | ColumndocsRphyRpdDevExtSwImageSupportSwImageServerType | read-only | current | This attribute reports the server Internet address type of the server from which the RPD's selected software image was downloaded. The RPD preserves the value … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.20.1.6 | ColumndocsRphyRpdDevExtSwImageSupportSwImageServerAddress | read-only | current | This attribute reports the Internet address of the server from which the RPD's selected software image was downloaded. The RPD preserves the value of this attr… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.21 | TabledocsRphyRpdDevSwImageCapTable | not-accessible | current | This table provides information about the software image capabilities of the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.21.1 | RowdocsRphyRpdDevSwImageCapEntry | not-accessible | current | The conceptual row of docsRphyRpdDevSwImageCapTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.21.1.1 | ColumndocsRphyRpdDevSwImageCapNumSwImages | read-only | current | This attribute reports the number of software images that the RPD supports. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.21.1.2 | ColumndocsRphyRpdDevSwImageCapImageUpgradability | read-only | current | Bitmask indicating whether the RPD supports SSD of the corresponding sowtware image. For example, bit 0 corresponds to software image with index 0, bit 1 corre… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.22 | TabledocsRphyRpdDevGcpCapTable | not-accessible | current | This table provides information about the gcp capabilities of the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.22.1 | RowdocsRphyRpdDevGcpCapEntry | not-accessible | current | The conceptual row of docsRphyRpdDevGcpCapTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.22.1.1 | ColumndocsRphyRpdDevGcpCapGcpKaResponseTime | read-only | current | This attribute reports how quickly the RPD can respond to GCP Keep Alive messages. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.23 | TabledocsRphyRpdDevOfdmCfgCapTable | not-accessible | current | This table provides information about the ofdm cfg capabilities of the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.23.1 | RowdocsRphyRpdDevOfdmCfgCapEntry | not-accessible | current | The conceptual row of docsRphyRpdDevOfdmCfgCapTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.23.1.1 | ColumndocsRphyRpdDevOfdmCfgCapReqOfdmaImDurationCfg | read-only | current | This attribute is a Boolean value that reports the RPDs need to explicitly configure IM grant duration for OFDMA channels. The RPD reports a value of false(0) … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.23.1.2 | ColumndocsRphyRpdDevOfdmCfgCapSupportedPilotPatterns | read-only | current | This attribute reports the set of supported OFDMA optional pilot patterns for an RPD. The RPD reports '0' for the bit corresponding to a pilot pattern not supp… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.23.1.3 | ColumndocsRphyRpdDevOfdmCfgCapNumDsOfdmProfiles | read-only | current | This attribute reports how many OFDM profiles are supported by the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.23.1.4 | ColumndocsRphyRpdDevOfdmCfgCapOptionalOfdmModulations | read-only | current | This attribute reports whether the RPD supports optional OFDM modulation orders defined in [PHYv4.0]. The RPD reports '0' for the bit corresponding to an OFDM … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.23.1.5 | ColumndocsRphyRpdDevOfdmCfgCapOptionalOfdmaModulations | read-only | current | This attribute reports whether the RPD supports optional OFDMA modulation orders defined in [PHYv4.0]. The RPD reports '0' for the bit corresponding to an OFDM… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.24 | TabledocsRphyRpdDevCoreRedundancyCapTable | not-accessible | current | This table provides information about the core redundancy capabilities of the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.24.1 | RowdocsRphyRpdDevCoreRedundancyCapEntry | not-accessible | current | The conceptual row of docsRphyRpdDevCoreRedundancyCapTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.24.1.1 | ColumndocsRphyRpdDevCoreRedundancyCapSupportsRedundancy | read-only | current | This attribute is a bit mask indicating whether the RPD supports HandoverToBackup, ConnectionStatus, and/or ReconnectFromCore features as indicated below: xxxx… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.25 | TabledocsRphyRpdDevResetCapTable | not-accessible | current | This table provides information about the reset capabilities of the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.25.1 | RowdocsRphyRpdDevResetCapEntry | not-accessible | current | The conceptual row of docsRphyRpdDevResetCapTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.25.1.1 | ColumndocsRphyRpdDevResetCapSupportsReset | read-only | current | This attribute is a bitmask indicating whether the RPD supports SoftReset, NvReset, or FactoryReset as indicated below: xxxxxxx0: RPD does not support SoftRese… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.25.1.2 | ColumndocsRphyRpdDevResetCapResetHistorySize | read-only | current | This attribute provides the maximum size of the ResetHistory table. The RPD is required to support a minimum of 50 entries in the ResetHistory table. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.26 | TabledocsRphyRpdDevFdxCapTable | not-accessible | current | This table provides information about the full-duplex capabilities of the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.26.1 | RowdocsRphyRpdDevFdxCapEntry | not-accessible | current | The conceptual row of docsRphyRpdDevFdxCapTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.26.1.1 | ColumndocsRphyRpdDevFdxCapSupportsFdx | read-only | current | This attribute reports the RPDs capability to support FDX operation. The value 0 (false) indicates the RPD does not support FDX operation. The value 1 (true) i… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.26.1.2 | ColumndocsRphyRpdDevFdxCapSupportsZblInsertion | read-only | current | This attribute reports the RPDs capability to receive the Zero Bit Loading (ZBL) Insertion message and insert ZBL as directed by the message. The RPD reports a… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.26.1.3 | ColumndocsRphyRpdDevFdxCapZblInsMsgLeadTime | read-only | current | This attribute reports the minimum lead time required by the RPD to receive the ZBL Insertion message ahead of the starting timestamp. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.27 | TabledocsRphyRpdDevRdtiCapTable | not-accessible | current | This table reports the RPD's capabilities related to time synchronization. The RdtiCapabilities TLV Type is 50.34. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.27.1 | RowdocsRphyRpdDevRdtiCapEntry | not-accessible | current | The conceptual row of docsRphyRpdDevRdtiCapTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.27.1.1 | ColumndocsRphyRpdDevRdtiCapNumPtpPortsPerEnetPort | read-only | current | This attribute reports how many PTP ports the RPD supports per CIN-facing Ethernet port. If the RPD does not support PTP port configuration from the CCAP Core,… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.27.1.2 | ColumndocsRphyRpdDevRdtiCapSupportsSyncE | read-only | current | This attribute reports whether the RPD supports synchronous Ethernet (SyncE). When the value of this attribute is reported as 'true', the RPD supports SyncE. W… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.27.1.3 | ColumndocsRphyRpdDevRdtiCapSupportsG8275d1 | read-only | current | This attribute reports whether the RPD supports G.8275.1 PTP profile. When the value of this attribute is reported as 'true', the RPD supports G.8275.1 profile… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.27.1.4 | ColumndocsRphyRpdDevRdtiCapSupportsDtpPseudowire | read-only | current | This attribute reports whether the RPD supports the DTP pseudowire. When the value of this attribute is reported as 'true', the RPD supports the DTP pseudowire… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.28 | TabledocsRphyRpdDevDsCapTable | not-accessible | current | This table reports the RPD's OFDM downstream channel capabilities. The DsCapabilities TLV Type is 50.51. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.28.1 | RowdocsRphyRpdDevDsCapEntry | not-accessible | current | The conceptual row of docsRphyRpdDevDsCapTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.28.1.1 | ColumndocsRphyRpdDevDsCapScQamInterleaverSupport | read-only | current | This attribute reports the RPDs support for interleaver settings for downstream SC-QAM channels. The value is a bitmask specifying which of 13 downstream SC-QA… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.28.1.2 | ColumndocsRphyRpdDevDsCapMaxDocsisScQamChannels | read-only | current | This attribute reports the maximum number of downstream DOCSIS SC-QAM channels the RPD can be configured to support on each downstream RF port. A downstream DO… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.28.1.3 | ColumndocsRphyRpdDevDsCapMaxMultipleScQamPspSessions | read-only | current | This attribute reports the maximum number of PSP sessions with more than one SC-QAM channel that the RPD can support per downstream RF port. Currently, multipl… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.28.1.4 | ColumndocsRphyRpdDevDsCapMaxNumBdrs | read-only | current | This attribute reports the maximum number of BDRs supported by the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.28.1.5 | ColumndocsRphyRpdDevDsCapMaxNumBcgs | read-only | current | This attribute reports the maximum number of BCGs supported by the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.28.1.6 | ColumndocsRphyRpdDevDsCapSupportsDsScQamModulationQam128 | read-only | current | This attribute reports whether the RPD supports QAM128 modulation for DS SC-QAM video channels. When the value of this attribute is reported as 'true', the RPD… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.28.1.7 | ColumndocsRphyRpdDevDsCapSupportsTiltMinimumFrequency | read-only | current | This attribute reports whether the RPD supports TiltMinimumFrequency TLV 61.9 for configuring downstream tilt slope. When the value of this attribute is report… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.29 | TabledocsRphyRpdDevSpecCaptureCapTable | not-accessible | current | This table reports RPD capabilities for Upstream Triggered Spectrum Capture Proactive Network Management functionality. The SpectrumCaptureCapabilities TLV Typ… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.29.1 | RowdocsRphyRpdDevSpecCaptureCapEntry | not-accessible | current | The conceptual row of docsRphyRpdDevSpecCaptureCapTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.29.1.1 | ColumndocsRphyRpdDevSpecCaptureCapNumSacs | read-only | current | This attribute reports the number of Spectrum Analysis Circuits (SACs) the RPD supports. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.30 | TabledocsRphyRpdDevSacCapTable | not-accessible | current | This table reports the capabilities of each Spectrum Analysis Circuit implemented in the RPD. The SacCapabilities TLV Type is 50.59.2. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.30.1 | RowdocsRphyRpdDevSacCapEntry | not-accessible | current | The conceptual row of docsRphyRpdDevSacCapTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.30.1.1 | ColumndocsRphyRpdDevSacCapSacIndex | not-accessible | current | This attribute uniquely identifies a SAC in an RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.30.1.2 | ColumndocsRphyRpdDevSacCapSacDescription | read-only | current | This attribute is a human readable description of a SAC, for example: Wideband Spectrum Analysis Circuit, frequency range 5-85 MHz. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.30.1.3 | ColumndocsRphyRpdDevSacCapMaxCaptureSpan | read-only | current | This attribute reports the maximum value of the frequency span supported by the SAC |
| 1.3.6.1.4.1.4491.2.1.30.1.1.30.1.4 | ColumndocsRphyRpdDevSacCapMinCaptureFreq | read-only | current | This attribute reports the lowest limit of the spectrum that can be captured by the SAC. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.30.1.5 | ColumndocsRphyRpdDevSacCapMaxCaptureFreq | read-only | current | This attribute reports the upper limit of the spectrum that can be captured by the SAC. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.30.1.6 | ColumndocsRphyRpdDevSacCapSuppTriggerModes | read-only | current | This attribute reports the Triggered Spectrum Capture trigger modes the RPD SAC supports. The value is a bitmask specifying which of 7 spectrum capture trigger… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.30.1.7 | ColumndocsRphyRpdDevSacCapSuppOutputFormats | read-only | current | This attribute reports the Triggered Spectrum Capture output data file formats the RPD SAC supports. The value is a bitmask specifying which of 6 output data f… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.30.1.8 | ColumndocsRphyRpdDevSacCapSuppWindowFormats | read-only | current | This attribute reports the Triggered Spectrum Capture data sample window functions the RPD SAC supports. The value is a bitmask specifying which of 7 window fu… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.30.1.9 | ColumndocsRphyRpdDevSacCapSuppAveraging | read-only | current | This attribute reports the RPD SACs capability to support Triggered Spectrum Capture data averaging. The value 0 (false) indicates the SAC does not support the… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.30.1.10 | ColumndocsRphyRpdDevSacCapSuppAggrMethods | read-only | current | This attribute reports the Triggered Spectrum Capture data aggregation methods the RPD SAC supports. The value is a bitmask specifying which aggregation method… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.30.1.11 | ColumndocsRphyRpdDevSacCapSuppSpecQual | read-only | current | This attribute reports the SACs capability to support Triggered Spectrum Capture spectrum qualification. The value 0 (false) indicates the SAC does not support… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.30.1.12 | ColumndocsRphyRpdDevSacCapMaxNumBins | read-only | current | This attribute reports the maximum number of Fast Fourier Transform (FFT) bins the RPDs SAC supports for Triggered Spectrum Capture. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.30.1.13 | ColumndocsRphyRpdDevSacCapMinNumBins | read-only | current | This attribute reports the minimum number of Fast Fourier Transform (FFT) bins the RPDs SAC supports for Triggered Spectrum Capture. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.30.1.14 | ColumndocsRphyRpdDevSacCapMinRepeatPeriod | read-only | current | This attribute reports the minimum duration of the RepeatPeriod supported by the SAC. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.30.1.15 | ColumndocsRphyRpdDevSacCapSuppTrigChanTypes | read-only | current | This attribute reports all supported channel types that can be used for triggers by the SAC. The value is a bitmask specifying which channel types the SAC is c… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.30.1.16 | ColumndocsRphyRpdDevSacCapPwType | read-only | current | This attribute reports which pseudowire (PW) types the SAC is capable of using. The value is a bitmask specifying which PW types the SAC is capable of using. T… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.30.1.17 | ColumndocsRphyRpdDevSacCapLowestCapturePort | read-only | current | This attribute reports the lowest upstream RF port index the SAC can operate on. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.30.1.18 | ColumndocsRphyRpdDevSacCapHighestCapturePort | read-only | current | This attribute reports the highest upstream RF port index the SAC can operate on. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.30.1.19 | ColumndocsRphyRpdDevSacCapSuppScanCapture | read-only | current | This attribute indicates whether the SAC supports Port Scanning Capture. Port Scanning Capture is a method of operation in free-running mode in which the SAC s… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.30.1.20 | ColumndocsRphyRpdDevSacCapMinScanRepeatPeriod | read-only | current | This attribute reports the minimum duration of the RepeatPeriod the SAC supports when it is operating in Port Scanning Capture. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.31 | TabledocsRphyRpdDevCandidateBackupCoresTable | not-accessible | current | This table provides a list of IP addresses of those CCAP Cores which are to be contacted by the RPD as potential backups to the selected Core. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.31.1 | RowdocsRphyRpdDevCandidateBackupCoresEntry | not-accessible | current | The conceptual row of docsRphyRpdDevCandidateBackupCoresTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.31.1.1 | ColumndocsRphyRpdDevCandidateBackupCoresBackupCoreIpAddrIndex | not-accessible | current | This key attribute identifies a row in CandidateBackupCores table. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.31.1.2 | ColumndocsRphyRpdDevCandidateBackupCoresBackupCoreAddrType | read-only | current | This attribute represents the IP address type of the potential backup CCAP Core. This value is of type InetAddressType, which is defined by [RFC 4001]. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.31.1.3 | ColumndocsRphyRpdDevCandidateBackupCoresBackupCoreAddr | read-only | current | This attribute reports the IPv4 or IPv6 address of the CCAP Core that the RPD needs to contact as a potential backup. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.32 | TabledocsRphyRpdDevShelfInfoTable | not-accessible | current | This table identifies RPD shelves and each RPD in the shelf. The CCAP Core MUST create an RpdShelfInfo entry for each RPD reporting a chassis entity with Entit… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.32.1 | RowdocsRphyRpdDevShelfInfoEntry | not-accessible | current | The conceptual row of docsRphyRpdDevShelfInfoTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.32.1.1 | ColumndocsRphyRpdDevShelfInfoShelfId | not-accessible | current | This attribute specifies the SerialNum of the RPD Entity with EntityIndex equal one and class equal 'chassis'. All RPDs reporting the same SerialNum for the ch… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.32.1.2 | ColumndocsRphyRpdDevShelfInfoRpdSlot | read-only | current | This attribute reports the slot number or, for RPDs not in a slot, the location number for an RPD in a shelf. If the main RPD module is in a container (i.e., h… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.33 | TabledocsRphyRpdDevPmapCapTable | not-accessible | current | The PMAP capabilities table allows the RPD to inform the CCAP Core about its capabilities related to OFDMA probes and P-MAP messages. The PmapCapabilities TLV … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.33.1 | RowdocsRphyRpdDevPmapCapEntry | not-accessible | current | The conceptual row of docsRphyRpdDevPmapCapTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.33.1.1 | ColumndocsRphyRpdDevPmapCapMaxNumPmaples | read-only | current | This attribute reports the maximum number of P-IEs per P-MAP supported by the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.33.1.2 | ColumndocsRphyRpdDevPmapCapProbePowerControl | read-only | current | This attribute reports whether the RPD supports Power Control (P) bit in P-MAP messages. The RPD reports a value of false(0) if the RPD does not support P-bit … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.33.1.3 | ColumndocsRphyRpdDevPmapCapSupportedPilotPatterns | read-only | current | This attribute reports the set of supported OFDMA optional pilot patterns for an RPD. The RPD reports '0' for the bit corresponding to a pilot pattern not supp… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.34 | TabledocsRphyRpdDevEchoCanCapTable | not-accessible | current | The Echo Canceller Capabilities table reports RPD support for various FDX Node Echo Canceller functions. The FdxCapabilities TLV Type is 50.57.4 |
| 1.3.6.1.4.1.4491.2.1.30.1.1.34.1 | RowdocsRphyRpdDevEchoCanCapEntry | not-accessible | current | The conceptual row of docsRphyRpdDevEchoCanCapTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.34.1.1 | ColumndocsRphyRpdDevEchoCanCapEctMethod | read-only | current | This attribute reports which EC training method is supported by the RPD. other: The EC training method supported by the RPD is not covered by this specificatio… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.34.1.2 | ColumndocsRphyRpdDevEchoCanCapMaxEctChannels | read-only | current | This attribute reports the maximum number of FDX OFDMA channels on which the RPD can train simultaneously. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.34.1.3 | ColumndocsRphyRpdDevEchoCanCapMinEctPeriod | read-only | current | This attribute reports the minimum EC training period the RPD can accept and still process EC Training Opportunities. A value of zero means that the RPD can ac… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.34.1.4 | ColumndocsRphyRpdDevEchoCanCapErdDuration | read-only | current | This attribute reports the RPD EC Re-convergence Delay (ERD). ERD is intended to permit the RPD ample time to determine EC coefficients and load them into the … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.35 | TabledocsRphyRpdDevRfmCapTable | not-accessible | current | The RFM capabilities table allows an RPD designed to operate in an optical node to communicate its capabilities for configuration and status reporting for feat… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.35.1 | RowdocsRphyRpdDevRfmCapEntry | not-accessible | current | The conceptual row of docsRphyRpdDevRfmCapTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.35.1.1 | ColumndocsRphyRpdDevRfmCapSupportsRfmMgmt | read-only | current | This attribute reports whether the RPD supports management of the RFM. The RPD reports a value of false(0) if it does not support RFM management. The RPD repor… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.35.1.2 | ColumndocsRphyRpdDevRfmCapNumNodeRfPorts | read-only | current | This attribute reports how many node RF ports the RPD supports. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.35.1.3 | ColumndocsRphyRpdDevRfmCapSupportsDsCfgRfmGain | read-only | current | This attribute reports whether the RPD supports configuration of the RFM downstream power gain via GCP. The RPD reports a value of false(0) if it does not supp… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.35.1.4 | ColumndocsRphyRpdDevRfmCapMinDsCfgRfmGain | read-only | current | This attribute reports the RPD's minimum supported value of the RFM DS power gain configuration. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.35.1.5 | ColumndocsRphyRpdDevRfmCapMaxDsCfgRfmGain | read-only | current | This attribute reports the RPD's maximum supported value of the RFM DS power gain configuration. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.35.1.6 | ColumndocsRphyRpdDevRfmCapSupportsUsCfgRfmGain | read-only | current | This attribute reports whether the RPD supports configuration of the RFM upstream power gain via GCP. The RPD reports a value of false(0) if it does not suppor… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.35.1.7 | ColumndocsRphyRpdDevRfmCapMinUsCfgRfmGain | read-only | current | This attribute reports the RPD's minimum supported value of the RFM US power gain configuration. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.35.1.8 | ColumndocsRphyRpdDevRfmCapMaxUsCfgRfmGain | read-only | current | This attribute reports the RPD's maximum supported value of the RFM US power gain configuration. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.35.1.9 | ColumndocsRphyRpdDevRfmCapSupportsRfmDsTiltConfig | read-only | current | This attribute reports whether the RPD supports configuration of the RFM downstream tilt via GCP. The RPD reports a value of false(0) if it does not support GC… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.35.1.10 | ColumndocsRphyRpdDevRfmCapMinRfmDsTilt | read-only | current | This attribute reports the RPD's minimum supported value of the RFM DS tilt configuration. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.35.1.11 | ColumndocsRphyRpdDevRfmCapMaxRfmDsTilt | read-only | current | This attribute reports the RPD's maximum supported value of the RFM DS tilt configuration. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.35.1.12 | ColumndocsRphyRpdDevRfmCapMaxDsPowerGainFunctions | read-only | current | This attribute reports how many distinct DS power control functions (i.e., typically amplifiers) the RPD supports in the RFM. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.35.1.13 | ColumndocsRphyRpdDevRfmCapMaxUsPowerGainFunctions | read-only | current | This attribute reports how many distinct US power control functions (i.e., typically attenuators) the RPD supports in the RFM. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.35.1.14 | ColumndocsRphyRpdDevRfmCapMaxDsTiltCtrlFunctions | read-only | current | This attribute reports how many distinct DS tilt control functions the RPD supports in the RFM. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.35.1.15 | ColumndocsRphyRpdDevRfmCapMinRfmDsFreq | read-only | current | This attribute reports the RPD's minimum DS frequency supported by the RFM. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.35.1.16 | ColumndocsRphyRpdDevRfmCapMaxRfmDsFreq | read-only | current | This attribute reports the RPD's maximum DS frequency supported by the RFM. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.36 | TabledocsRphyRpdDevNodeRfPortCapTable | not-accessible | current | The Node RF Port Capabilities table reports the RPD configuration capabilities of the RFM Node RF ports. The NodeRfPortCapabilities TLV Type is 50.60.17. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.36.1 | RowdocsRphyRpdDevNodeRfPortCapEntry | not-accessible | current | The conceptual row of docsRphyRpdDevNodeRfPortCapTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.36.1.1 | ColumndocsRphyRpdDevNodeRfPortCapNodeRfPortIndex | not-accessible | current | This attribute is used to identify a node RF port in the RFM. For the purpose of GCP management node RF ports are numbered from 0 to N-1, where N is the number… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.36.1.2 | ColumndocsRphyRpdDevNodeRfPortCapNodeRfPortVendorDesc | read-only | current | This attribute reports the RPD's human readable description of the node RF Port. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.36.1.3 | ColumndocsRphyRpdDevNodeRfPortCapRpdUsRfPortMap | read-only | current | This attribute reports the index association of the node RF port to the US RF Port in the RPD Module. If an RPD supports configurable mapping between node RF p… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.36.1.4 | ColumndocsRphyRpdDevNodeRfPortCapRpdDsRfPortMap | read-only | current | This attribute reports the index association of the node RF port to the DS RF Port in the RPD Module. If an RPD supports configurable mapping between node RF p… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.36.1.5 | ColumndocsRphyRpdDevNodeRfPortCapRfmUsGainCtrlIndex | read-only | current | This attribute reports the RPD's index association of the node RF port with US gain control function in the RFM. An RPN with only downstream Partial Spectrum c… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.36.1.6 | ColumndocsRphyRpdDevNodeRfPortCapRfmDsGainCtrlIndex | read-only | current | This attribute reports the RPD's index association of the node RF port with DS gain control function in the RFM. An RPN with only upstream Partial Spectrum cap… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.36.1.7 | ColumndocsRphyRpdDevNodeRfPortCapRfmDsTiltCtrlIndex | read-only | current | This attribute reports the RPD's index association of the node RF port with DS tilt control function in the RFM. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.36.1.8 | ColumndocsRphyRpdDevNodeRfPortCapNodeRfPortOpLabel | read-only | current | This attribute reports the RPD's operator label of the node RF Port. The default value is the zero-length string. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.37 | TabledocsRphyRpdDevResetHistoryTable | not-accessible | current | This table provides a record of the occurrences of a reset of an RPD. The RPD can reset for many reasons, including loss of Principal Core, loss of IP connecti… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.37.1 | RowdocsRphyRpdDevResetHistoryEntry | not-accessible | current | The conceptual row of docsRphyRpdDevResetHistoryTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.37.1.1 | ColumndocsRphyRpdDevResetHistoryIndex | not-accessible | current | This attribute is a key and provides an index into the table. Indexes are consecutively ordered from 0..N-1 where N is the maximum number of reset history even… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.37.1.2 | ColumndocsRphyRpdDevResetHistoryResetTimestamp | read-only | current | This attribute provides the time at which the reset occurred. If the RPD does not know what time the RPD reset occurred, the RPD MAY report a value of midnight… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.37.1.3 | ColumndocsRphyRpdDevResetHistoryType | read-only | current | This attribute identifies the type of reset that the RPD is recording. The possible values match those of the Type TLV (TLV 40.1.1, sub-TLV of ResetCtrl) and v… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.37.1.4 | ColumndocsRphyRpdDevResetHistoryReason | read-only | current | This attribute provides a vendor-specific string with a detailed explanation of why the RPD was reset. Vendors are expected to add additional details, includin… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.37.1.5 | ColumndocsRphyRpdDevResetHistoryEventIdRef | read-only | current | If the reset was related to an event that was captured in a standardized DOCSIS event, this attribute provides the event ID of the corresponding event. If the … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.37.1.6 | ColumndocsRphyRpdDevResetHistoryEventDescription | read-only | current | If the reset was related to an event that was captured in a standardized DOCSIS event, this attribute provides the standardized description of the correspondin… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.37.1.7 | ColumndocsRphyRpdDevResetHistoryRecoveryTime | read-only | current | This attribute provides the number of seconds that have elapsed between the time the reset event started and the completion of the local RPD initialization sta… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.37.1.8 | ColumndocsRphyRpdDevResetHistoryPrincipalOpTimestamp | read-only | current | This attribute provides the time at which the RPD was moved to operational by the Principal Core. If the RPD is unable to acquire the time of day by the time t… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.38 | TabledocsRphyRpdDevChanBcastGroupStatusTable | not-accessible | current | This table indicates whether a downstream SC-QAM channel on an RPD is part of a BCG. Downstream SC-QAM channels on same RPD with the same channel selector chan… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.38.1 | RowdocsRphyRpdDevChanBcastGroupStatusEntry | not-accessible | current | The conceptual row of docsRphyRpdDevChanBcastGroupStatusTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.38.1.1 | ColumndocsRphyRpdDevChanBcastGroupStatusRfPortIndex | not-accessible | current | This key attribute is the RF port number from the channel selector for this DS SC-QAM channel. This is part of a channel selector. A Partial Spectrum-capable R… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.38.1.2 | ColumndocsRphyRpdDevChanBcastGroupStatusScQamIndex | not-accessible | current | This key attribute is the channel index from the channel selector for this DS SC-QAM channel. This is part of a channel selector. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.38.1.3 | ColumndocsRphyRpdDevChanBcastGroupStatusGroupMember | read-only | current | This attribute indicates whether or not this RPD's DS SC-QAM channel is part of a BCG. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.39 | TabledocsRphyRpdDevUsCapTable | not-accessible | current | The UsCapabilities table reports the RPD's upstream channel capabilities. The UsCapabilities TLV Type is 50.61. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.39.1 | RowdocsRphyRpdDevUsCapEntry | not-accessible | current | The conceptual row of docsRphyRpdDevUsCapTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.39.1.1 | ColumndocsRphyRpdDevUsCapMaxUsFrequency | read-only | current | This attribute reports the maximum frequency of any upstream signal that the RPD supports on a US RF port. It defines the highest frequency of the encompassed … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.39.1.2 | ColumndocsRphyRpdDevUsCapMinUsFrequency | read-only | current | This attribute reports the minimum frequency of any upstream signal that the RPD supports on a US RF port. It defines the lowest frequency of the encompassed s… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.39.1.3 | ColumndocsRphyRpdDevUsCapMaxUnicastSids | read-only | current | This attribute reports the maximum number of unicast SIDs concurrently supported by the RPD on any upstream channel. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.40 | TabledocsRphyRpdDevPmtudCapTable | not-accessible | current | The PmtudCapabilities table reports the RPD capabilities for Path MTU Discovery support for control plane connections. The PmtudCapabilities TLV Type is 50.62. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.40.1 | RowdocsRphyRpdDevPmtudCapEntry | not-accessible | current | The conceptual row of docsRphyRpdDevPmtudCapTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.40.1.1 | ColumndocsRphyRpdDevPmtdudCapSupportsIcmpBasedPmtud | read-only | current | This attribute reports the RPD's support of PMTUD based on [RFC 1191] and [RFC 8201]. The RPD reports a value of 'false' if it does not support PMTUD based on … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.40.1.2 | ColumndocsRphyRpdDevPmtdudCapSupportsPacketizationBasedPmtud | read-only | current | This attribute reports the RPD's support of PMTUD based on [RFC 4821]. The RPD reports a value of 'false' if it does not support PMTUD based on [RFC 4821]. The… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.41 | TabledocsRphyRpdDevPnmCapTable | not-accessible | current | The PnmCapabilities table reports the RPD's capabilities for PNM test functionality. An RPD that implements PNM functions implements the DOCSIS PNM MIB module … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.41.1 | RowdocsRphyRpdDevPnmCapEntry | not-accessible | current | The conceptual row of docsRphyRpdDevPnmCapTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.41.1.1 | ColumndocsRphyRpdDevPnmCapSupportedPnmTests | read-only | current | The SupportedPnmTests attribute allows an RPD to communicate which PNM tests it supports. SupportedPnmTests is represented as a bitmask with each assigned bit … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.42 | TabledocsRphyRpdDevUpcCapTable | not-accessible | current | The UpcCapabilities table reports the RPD capabilities for Upstream Probe Capture PNM tests. The UpcCapabilities TLV Type is 50.64.2. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.42.1 | RowdocsRphyRpdDevUpcCapEntry | not-accessible | current | The conceptual row of docsRphyRpdDevUpcCapTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.42.1.1 | ColumndocsRphyRpdDevUpcCapMinNumSymbols25Khz | read-only | current | This attribute reports the minimum number of probe symbols that can be captured by the RPD in one test when an OFDMA channel is configured for 25 kHz subcarrie… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.42.1.2 | ColumndocsRphyRpdDevUpcCapMaxNumSymbols25Khz | read-only | current | This attribute reports the maximum number of probe symbols that can be captured by the RPD in one test when an OFDMA channel is configured for 25 kHz subcarrie… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.42.1.3 | ColumndocsRphyRpdDevUpcCapMinNumSymbols50Khz | read-only | current | This attribute reports the minimum number of probe symbols that can be captured by the RPD in one test when an OFDMA channel is configured for 50 kHz subcarrie… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.42.1.4 | ColumndocsRphyRpdDevUpcCapMaxNumSymbols50Khz | read-only | current | This attribute reports the maximum number of probe symbols that can be captured by the RPD in one test when an OFDMA channel is configured for 50 kHz subcarrie… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.42.1.5 | ColumndocsRphyRpdDevUpcCapSupportsStaggeredPies | read-only | current | This attribute reports whether the RPD supports UPC PNM test with staggered Probe Information Elements (PIE), i.e., the RPD supports the use of a P-IE that spe… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.42.1.6 | ColumndocsRphyRpdDevUpcCapSupportsDedicatedPwUpcRxMer | read-only | current | This attribute reports whether the RPD supports dedicated pseudowires for UPC and RxMER PNM tests. The RPD reports a value of 'false' if it does not support de… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.42.1.7 | ColumndocsRphyRpdDevUpcCapSupportsFreqDomainSamples | read-only | current | This attribute reports whether the RPD supports UPC test with samples represented in frequency domain. The RPD reports a value of 'false' if it does not suppor… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.43 | TabledocsRphyRpdDevInitCapTable | not-accessible | current | The InitCapabilities table reports the RPD capabilities for initialization. The InitializationCapabilities TLV Type is 50.65. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.43.1 | RowdocsRphyRpdDevInitCapEntry | not-accessible | current | The conceptual row of docsRphyRpdDevInitCapTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.43.1.1 | ColumndocsRphyRpdDevInitCapPerCoreInitTimers | read-only | current | This attribute reports whether the RPD supports per Core initialization timers. The RPD reports a value of false(0) if it does not support per Core initializat… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.43.1.2 | ColumndocsRphyRpdDevInitCapStagingConfigInitTimers | read-only | current | This attribute reports whether the RPD supports setting initialization timers during staging. The RPD reports a value of false(0) if it does not support settin… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.44 | TabledocsRphyRpdDevUsPowerCapTable | not-accessible | current | The UsPowerCapabilities table reports the RPD capabilities related to upstream power management. The UsPowerCapabilities TLV Type is 50.49. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.44.1 | RowdocsRphyRpdDevUsPowerCapEntry | not-accessible | current | The conceptual row of docsRphyRpdDevUsPowerCapTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.44.1.1 | ColumndocsRphyRpdDevUsPowerCapMinTarRxPowerAdjust55d2 | read-only | current | This attribute reports the minimum value of the TargetRxPowerAdjust attribute that the RPD supports for SCTE 55-2 upstream channels. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.44.1.2 | ColumndocsRphyRpdDevUsPowerCapMaxTarRxPowerAdjust55d2 | read-only | current | This attribute reports the maximum value of the TargetRxPowerAdjust attribute that the RPD supports for SCTE 55-2 upstream channels. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.45 | TabledocsRphyRpdDevTrfStatsTable | not-accessible | current | The RpdTrfStats table is supported by an RPD that implements TRF and is used to report on the TRF activity by the RPD. The CCAP Core reads all attributes of an… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.45.1 | RowdocsRphyRpdDevTrfStatsEntry | not-accessible | current | The conceptual row of docsRphyRpdDevTrfStatsTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.45.1.1 | ColumndocsRphyRpdDevTrfStatsTunnelReplacements | read-only | current | This attribute counts the number of tunnels successfully replaced by the RPD due to reception of an SCCRQ containing a DEPI Replaced Tunnel ID AVP identifying … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.45.1.2 | ColumndocsRphyRpdDevTrfStatsTunnelReplacementFailures | read-only | current | This attribute counts the number of tunnel replacement attempts due to reception of an SCCRQ containing a DEPI Replaced Tunnel ID AVP by the RPD that failed. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.45.1.3 | ColumndocsRphyRpdDevTrfStatsTunnelHandovers | read-only | current | This attribute counts the number of tunnels successfully transitioned from standby to inService HA state by the RPD due to reception of a DTU message. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.45.1.4 | ColumndocsRphyRpdDevTrfStatsTunnelHandoverFailures | read-only | current | This attribute counts the number of tunnel handover attempts by the RPD that failed to transition from standby to inService HA state following reception of a D… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.46 | TabledocsRphyRpdDevLcceStatsTable | not-accessible | current | This table is reported by the CCAP Core on behalf of the RPD and is used to report on the DEPI L2TPv3 control connection activity between the RPD and all the C… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.46.1 | RowdocsRphyRpdDevLcceStatsEntry | not-accessible | current | The conceptual row of docsRphyRpdDevLcceStatsTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.46.1.1 | ColumndocsRphyRpdDevLcceStatsLcceIpAddrType | not-accessible | current | This key attribute indicates whether the IP address provided in the CcapLcceIpAddr and RpdLcceIpAddr attributes are IPv4 or IPv6. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.46.1.2 | ColumndocsRphyRpdDevLcceStatsCcapLcceIpAddr | not-accessible | current | This key attribute provides the LCCE IP address on the CCAP Core detailed in the instance. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.46.1.3 | ColumndocsRphyRpdDevLcceStatsRpdLcceIpAddr | not-accessible | current | This key attribute reports the RPD LCCE IP address detailed in the instance. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.46.1.4 | ColumndocsRphyRpdDevLcceStatsCtrlConnEst | read-only | current | This attribute counts the number of DEPI control connections successfully established between the RPD and CCAP Core LCCEs. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.46.1.5 | ColumndocsRphyRpdDevLcceStatsCtrlConnEstFailures | read-only | current | This attribute counts the number of DEPI control connections that failed during establishment between the RPD and CCAP Core LCCEs. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.46.1.6 | ColumndocsRphyRpdDevLcceStatsCtrlConnFailures | read-only | current | This attribute counts the number of DEPI control connections between the RPD and CCAP Core LCCEs in which a failure was detected (after successful tunnel estab… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.46.1.7 | ColumndocsRphyRpdDevLcceStatsCurrCtrlConn | read-only | current | This attribute counts the number of DEPI control connections that are currently operational between the RPD and CCAP Core LCCEs (i.e connections that are in an… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.47 | TabledocsRphyRpdDevCurrCtrlConnTable | not-accessible | current | This table is reported by the CCAP Core on behalf of the RPD and is used to report on the currently active DEPI L2TPv3 control connections on the RPD. The CCAP… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.47.1 | RowdocsRphyRpdDevCurrCtrlConnEntry | not-accessible | current | The conceptual row of docsRphyRpdDevCurrCtrlConnTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.47.1.1 | ColumndocsRphyRpdDevCurrCtrlConnLcceIpAddrType | not-accessible | current | This key attribute indicates whether the IP address provided in the CcapLcceIpAddr and RpdLcceIpAddr attributes are IPv4 or IPv6. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.47.1.2 | ColumndocsRphyRpdDevCurrCtrlConnCcapLcceIpAddr | not-accessible | current | This key attribute provides the LCCE IP address on the CCAP Core of the control connection detailed in the instance. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.47.1.3 | ColumndocsRphyRpdDevCurrCtrlConnRpdLcceIpAddr | not-accessible | current | This key attribute reports the RPD LCCE IP address of the control connection detailed in the instance. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.47.1.4 | ColumndocsRphyRpdDevCurrCtrlConnRpdConnCtrlId | not-accessible | current | This key attribute reports the RPD control connection identifier (CCID) for this control connection. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.47.1.5 | ColumndocsRphyRpdDevCurrCtrlConnCoreConnCtrlId | read-only | current | This attribute reports the Core control connection identifier (CCID) for this control connection. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.47.1.6 | ColumndocsRphyRpdDevCurrCtrlConnCoreId | read-only | current | This attribute reports the unique identifier of the CCAP Core with which this control connection terminates. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.47.1.7 | ColumndocsRphyRpdDevCurrCtrlConnUdpPort | read-only | current | This attribute reports the UDP Port reported by the RPD when the DEPI control connection uses L2TPv3 Header Over UDP. This attribute reports a value of 0 when … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.47.1.8 | ColumndocsRphyRpdDevCurrCtrlConnHaState | read-only | current | This attribute indicates the current HaState of the tunnel for which this DEPI control connection provides the signaling. If TRF is not supported by either the… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.47.1.9 | ColumndocsRphyRpdDevCurrCtrlConnSessEstFailures | read-only | current | This attribute counts the number of DEPI sessions that failed during establishment using this control connection. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.47.1.10 | ColumndocsRphyRpdDevCurrCtrlConnSessFailed | read-only | current | This attribute counts the number of DEPI sessions in which a failure was detected (after successful tunnel establishment) that led to the session being closed … |
| 1.3.6.1.4.1.4491.2.1.30.1.1.47.1.11 | ColumndocsRphyRpdDevCurrCtrlConnCurrSess | read-only | current | This attribute counts the number of current DEPI sessions using this control connection (i.e., sessions that are in an inService or standby state). Sessions th… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.48 | TabledocsRphyRpdDevTelemetryCapTable | not-accessible | current | This table reports the Telemetry Capabilities of the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.48.1 | RowdocsRphyRpdDevTelemetryCapEntry | not-accessible | current | The conceptual row of docsRphyRpdDevTelemetryCapTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.48.1.1 | ColumndocsRphyRpdDevTelemetryCapSupportsGnmiStreaming | read-only | current | This attribute reports the RPD's support for Streaming Telemetry using gRPC Network Management Interface (gNMI) protocol. Value 'true' indicates the RPD suppor… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.48.1.2 | ColumndocsRphyRpdDevTelemetryCapNumClientsSupported | read-only | current | This attribute reports the number of Telemetry Clients supported by the RPD. This attribute should be ignored if the value of SupportsStreamingTelemetry is 'fa… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.49 | TabledocsRphyRpdDevNodePortMapDsCapTable | not-accessible | current | The NodePortMap TLV 50.60.18 reports the topology of Node Port (NP) to Partial Spectrum RF port connections. The presence of the NodePortMap objects indicate t… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.49.1 | RowdocsRphyRpdDevNodePortMapDsCapEntry | not-accessible | current | The conceptual row of docsRphyRpdDevNodePortMapDsCapTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.49.1.1 | ColumndocsRphyRpdDevNodePortMapDsCapNodePortIndex | not-accessible | current | This attribute provides the Node Port index of an instance of the NodePortMapDs table. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.49.1.2 | ColumndocsRphyRpdDevNodePortMapDsCapDsRfPortIndex | not-accessible | current | This attribute provides the downstream RF port index of an instance of the NodePortMapDs object. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.49.1.3 | ColumndocsRphyRpdDevNodePortMapDsCapGainControlIndex | read-only | current | This attribute reports the downstream gain control index to configure in the DsPowerGainIndex (TLV 160.1.1) to configure the pairwise gain from Interface C pow… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.50 | TabledocsRphyRpdDevNodePortMapUsCapTable | not-accessible | current | The NodePortMap TLV 50.60.18 reports the topology of Node Port (NP) to Partial Spectrum RF port connections. The presence of the NodePortMap objects indicate t… |
| 1.3.6.1.4.1.4491.2.1.30.1.1.50.1 | RowdocsRphyRpdDevNodePortMapUsCapEntry | not-accessible | current | The conceptual row of docsRphyRpdDevNodePortMapUsCapTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.50.1.1 | ColumndocsRphyRpdDevNodePortMapUsCapNodePortIndex | not-accessible | current | This attribute provides the Node Port index of an instance of the NodePortMapUs table. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.50.1.2 | ColumndocsRphyRpdDevNodePortMapUsCapUsRfPortIndex | not-accessible | current | This attribute provides the upstream RF port index of an instance of the NodePortMapUs object. |
| 1.3.6.1.4.1.4491.2.1.30.1.1.50.1.3 | ColumndocsRphyRpdDevNodePortMapUsCapGainControlIndex | read-only | current | This attribute reports the upstream gain control index to configure in the UsPowerGainIndex (TLV 160.2.1) to set the pairwise gain from this instance's Node Po… |
| 1.3.6.1.4.1.4491.2.1.30.1.2 | NodedocsRphyRpdIfMibObjects | |||
| 1.3.6.1.4.1.4491.2.1.30.1.2.1 | TabledocsRphyRpdIfPhysEntityTable | not-accessible | current | This table reports entities that exist within each Remote PHY Node that is communicating with the CCAP Core. Because the entities exist within the Remote PHY N… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.1.1 | RowdocsRphyRpdIfPhysEntityEntry | not-accessible | current | Information about a particular physical entity. Each entry provides objects (docsRphyRpdIfPhysEntityDescr, docsRphyRpdIfPhysEntityVendorType, and docsRphyRpdIf… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.1 | ColumndocsRphyRpdIfPhysEntityIndex | not-accessible | current | This key attribute reports an arbitrary value that uniquely identifies the physical entity. Index values for different physical entities are not necessarily co… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.2 | ColumndocsRphyRpdIfPhysEntityDescr | read-only | current | A textual description of physical entity. This object should contain a string that identifies the manufacturer's name for the physical entity and should be set… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.3 | ColumndocsRphyRpdIfPhysEntityVendorType | read-only | current | An indication of the vendor-specific hardware type of the physical entity. Note that this is different from the definition of MIB-II's sysObjectID. An agent sh… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.4 | ColumndocsRphyRpdIfPhysEntityContainedIn | read-only | current | The value of docsRphyRpdIfPhysEntityIndex for the physical entity that 'contains' this physical entity. A value of zero indicates this physical entity is not c… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.5 | ColumndocsRphyRpdIfPhysEntityClass | read-only | current | An indication of the general hardware type of the physical entity. An agent should set this object to the standard enumeration value that most accurately indic… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.6 | ColumndocsRphyRpdIfPhysEntityParentRelPos | read-only | current | An indication of the relative position of this 'child' component among all its 'sibling' components. Sibling components are defined as docsRphyRpdIfPhysEntityE… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.7 | ColumndocsRphyRpdIfPhysEntityName | read-only | current | The textual name of the physical entity. The value of this object should be the name of the component as assigned by the local device and should be suitable fo… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.8 | ColumndocsRphyRpdIfPhysEntityHardwareRev | read-only | current | The vendor-specific hardware revision string for the physical entity. The preferred value is the hardware revision identifier actually printed on the component… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.9 | ColumndocsRphyRpdIfPhysEntityFirmwareRev | read-only | current | The vendor-specific firmware revision string for the physical entity. Note that if revision information is stored internally in a non-printable (e.g., binary) … |
| 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.10 | ColumndocsRphyRpdIfPhysEntitySoftwareRev | read-only | current | The vendor-specific software revision string for the physical entity. Note that if revision information is stored internally in a non-printable (e.g., binary) … |
| 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.11 | ColumndocsRphyRpdIfPhysEntitySerialNum | read-only | current | The vendor-specific serial number string for the physical entity. The preferred value is the serial number string actually printed on the component itself (if … |
| 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.12 | ColumndocsRphyRpdIfPhysEntityMfgName | read-only | current | The name of the manufacturer of this physical component. The preferred value is the manufacturer name string actually printed on the component itself (if prese… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.13 | ColumndocsRphyRpdIfPhysEntityModelName | read-only | current | The vendor-specific model name identifier string associated with this physical component. The preferred value is the customer-visible part number, which may be… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.14 | ColumndocsRphyRpdIfPhysEntityAlias | read-only | current | This attribute reports an 'alias' name for the physical entity, as specified by a network manager, and provides a non-volatile 'handle' for the physical entity… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.15 | ColumndocsRphyRpdIfPhysEntityAssetID | read-only | current | This object is a user-assigned asset tracking identifier (as specified by a network manager) for the physical entity, and provides non-volatile storage of this… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.16 | ColumndocsRphyRpdIfPhysEntityIsFRU | read-only | current | This object indicates whether or not this physical entity is considered a 'field replaceable unit' by the vendor. If this object contains the value 'true(1)', … |
| 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.17 | ColumndocsRphyRpdIfPhysEntityMfgDate | read-only | current | This object contains the date of manufacturing of the managed entity. If the manufacturing date is unknown or not supported, the object is not instantiated. Th… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.18 | ColumndocsRphyRpdIfPhysEntityUris | read-only | current | This object contains identification information about the physical entity. The object contains URIs; therefore, the syntax of this object must conform to RFC 3… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.19 | ColumndocsRphyRpdIfPhysEntityUUID | read-only | current | This attribute contains identification information about the physical entity. The object contains a Universally Unique Identifier; the syntax of this attribute… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.2 | TabledocsRphyRpdIfPhysEntSensorTable | not-accessible | current | This table contains one row per physical sensor represented by an associated row in the docsRphyRpdIfPhysEntityTable. The CCAP Core reads the attributes of an … |
| 1.3.6.1.4.1.4491.2.1.30.1.2.2.1 | RowdocsRphyRpdIfPhysEntSensorEntry | not-accessible | current | Information about a particular physical sensor. An entry in this table describes the present reading of a sensor, the measurement units and scale, and sensor o… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.2.1.1 | ColumndocsRphyRpdIfPhysEntSensorType | read-only | current | This attribute reports the type of data returned by the associated Value attribute. The CCAP Core SHOULD set the value during instance creation. The CCAP Core … |
| 1.3.6.1.4.1.4491.2.1.30.1.2.2.1.2 | ColumndocsRphyRpdIfPhysEntSensorScale | read-only | current | This attribute reports a data scaling factor, represented with an International System of Units (SI) prefix. The actual data units are determined by examining … |
| 1.3.6.1.4.1.4491.2.1.30.1.2.2.1.3 | ColumndocsRphyRpdIfPhysEntSensorPrecision | read-only | current | This attribute reports the number of decimal places of precision in fixed-point sensor values returned by the associated Value attribute. This attribute should… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.2.1.4 | ColumndocsRphyRpdIfPhysEntSensorValue | read-only | current | This attribute reports the most recent measurement obtained by the RPD for this sensor. To correctly interpret the value of this object, the associated SensorT… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.2.1.5 | ColumndocsRphyRpdIfPhysEntSensorOperStatus | read-only | current | The operational status of the sensor. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.2.1.6 | ColumndocsRphyRpdIfPhysEntSensorUnitsDisplay | read-only | current | A textual description of the data units that should be used in the display of SensorValue. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.2.1.7 | ColumndocsRphyRpdIfPhysEntSensorValueTimeStamp | read-only | current | This attribute reports the value of RpdSysUpTime at the time the status and/or value of this sensor was last obtained by the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.2.1.8 | ColumndocsRphyRpdIfPhysEntSensorValueUpdateRate | read-only | current | This attribute reports an indication of the frequency that the CCAP Core updates the associated Value object, represented in milliseconds. The value zero indic… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.3 | TabledocsRphyRpdIfEnetTable | not-accessible | current | This table provides details about the Ethernet interfaces on the RPD. The attributes of this object are based on the ifTable/ifXTable specified in RFC 2863. Th… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.3.1 | RowdocsRphyRpdIfEnetEntry | not-accessible | current | An entry containing management information applicable to a particular interface. The Ethernet IfIndex is chosen by the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.1 | ColumndocsRphyRpdIfEnetPortIndex | not-accessible | current | This key attribute reports a unique index for this Ethernet port interface. This attribute is mapped to two RCP TLVs. TLV 87.2.1 is used when reading NetworkAu… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.2 | ColumndocsRphyRpdIfEnetDescr | read-only | current | A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the i… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.3 | ColumndocsRphyRpdIfEnetName | read-only | current | This attribute reports a textual string representing a name that describes the interface. The CCAP Core must populate this object with the ID that is used in G… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.4 | ColumndocsRphyRpdIfEnetAlias | read-only | current | This attribute reports an Alias for the interface. On the first instantiation of an interface, the value of Alias associated with that interface is the zero-le… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.5 | ColumndocsRphyRpdIfEnetType | read-only | current | This attribute reports the type of interface. Additional values for Type are assigned by the Internet Assigned Numbers Authority (IANA), through updating the s… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.6 | ColumndocsRphyRpdIfEnetMtu | read-only | current | This attribute reports the size of the largest packet which can be sent/received on the interface, specified in octets. For interfaces that are used for transm… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.7 | ColumndocsRphyRpdIfEnetPhysAddress | read-only | current | This attribute reports the interface's address at its protocol sub-layer. For example, for an 802.x interface, this attribute normally contains a MAC address. … |
| 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.8 | ColumndocsRphyRpdIfEnetAdminStatus | read-only | current | This attribute reports the state of the interface. The testing(3) state indicates that no operational packets can be passed. When a managed system initializes,… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.9 | ColumndocsRphyRpdIfEnetOperStatus | read-only | current | This attribute reports the current operational state of the interface. The testing(3) state indicates that no operational packets can be passed. If AdminStatus… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.10 | ColumndocsRphyRpdIfEnetLastChange | read-only | current | This attribute reports the value of RpdSysUpTime at the time the interface entered its current operational state. If the current state was entered prior to the… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.11 | ColumndocsRphyRpdIfEnetLinkUpDownTrapEnable | read-only | current | This attribute reports whether linkup/linkdown traps are generated for this interface. A value of true indicates that traps are enabled. A value of false indic… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.12 | ColumndocsRphyRpdIfEnetHighSpeed | read-only | current | This attribute reports an estimate of the interface's current bandwidth in units of 1,000,000 bits per second. If this attribute reports a value of 'n' then th… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.13 | ColumndocsRphyRpdIfEnetPromiscuousMode | read-only | current | This attribute reports a value of '2' (false) if this interface only accepts packets/frames that are addressed to this interface. This attribute reports a valu… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.14 | ColumndocsRphyRpdIfEnetConnectorPresent | read-only | current | This attribute reports the value 'true' if the interface sublayer has a physical connector and the value 'false' otherwise. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.15 | ColumndocsRphyRpdIfEnetNetworkAuthStatus | read-only | current | This attribute reports the network authentication status of this interface. other: The interface is in a state not listed below. waitForEapReq: The interface i… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.4 | TabledocsRphyRpdIfEnetStatsTable | not-accessible | current | This table reports statistics for the Ethernet interfaces on the RPD. The attributes of this table are based on the ifTable/ifXTable specified in RFC 2863. The… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.4.1 | RowdocsRphyRpdIfEnetStatsEntry | not-accessible | current | An entry containing statistical information applicable to a particular RPD ethernet interface. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.1 | ColumndocsRphyRpdIfEnetStatsInOctets | read-only | current | The total number of octets received on the interface, including framing characters. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.2 | ColumndocsRphyRpdIfEnetStatsOutOctets | read-only | current | The total number of octets transmitted out of the interface, including framing characters. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.3 | ColumndocsRphyRpdIfEnetStatsInFrames | read-only | current | The total number of frames received on the interface, including framing characters. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.4 | ColumndocsRphyRpdIfEnetStatsOutFrames | read-only | current | The total number of frames transmitted out of the interface, including framing characters. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.5 | ColumndocsRphyRpdIfEnetStatsInUnicastOctets | read-only | deprecated | The number of octets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.6 | ColumndocsRphyRpdIfEnetStatsOutUnicastOctets | read-only | deprecated | The total number of octets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-l… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.7 | ColumndocsRphyRpdIfEnetStatsInUnicastFrames | read-only | current | The number of frames, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.8 | ColumndocsRphyRpdIfEnetStatsOutUnicastFrames | read-only | current | The total number of frames that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-l… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.9 | ColumndocsRphyRpdIfEnetStatsInMulticastOctets | read-only | deprecated | The number of octets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer proto… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.10 | ColumndocsRphyRpdIfEnetStatsOutMulticastOctets | read-only | deprecated | The total number of octets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including t… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.11 | ColumndocsRphyRpdIfEnetStatsInMulticastFrames | read-only | current | The number of frames, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer proto… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.12 | ColumndocsRphyRpdIfEnetStatsOutMulticastFrames | read-only | current | The total number of frames that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including t… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.13 | ColumndocsRphyRpdIfEnetStatsInBroadcastOctets | read-only | deprecated | The number of octets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.14 | ColumndocsRphyRpdIfEnetStatsOutBroadcastOctets | read-only | deprecated | The total number of octets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including t… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.15 | ColumndocsRphyRpdIfEnetStatsInBroadcastFrames | read-only | current | The number of frames, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.16 | ColumndocsRphyRpdIfEnetStatsOutBroadcastFrames | read-only | current | The total number of frames that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including t… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.17 | ColumndocsRphyRpdIfEnetStatsInDiscards | read-only | current | The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer pr… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.18 | ColumndocsRphyRpdIfEnetStatsOutDiscards | read-only | current | The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reaso… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.19 | ColumndocsRphyRpdIfEnetStatsInErrors | read-only | current | For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For char… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.20 | ColumndocsRphyRpdIfEnetStatsOutErrors | read-only | current | For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfac… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.21 | ColumndocsRphyRpdIfEnetStatsInUnknownProtos | read-only | current | For packet-oriented interfaces, the number of packets received via the interface which were discarded because of an unknown or unsupported protocol. For charac… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.22 | ColumndocsRphyRpdIfEnetStatsCounterDiscontinuityTime | read-only | current | This attribute reports the date and time at which any one or more of the counters in this group were created or last reset to zero. If the RPD does not acquire… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.5 | TabledocsRphyRpdIfRpdEnetToCoreEntityMapTable | not-accessible | current | If the RPD implements an Entity for an Ethernet port (which is optional), this table provides the mapping between the RPD's EnetPortIndex as signaled in GCP an… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.5.1 | RowdocsRphyRpdIfRpdEnetToCoreEntityMapEntry | not-accessible | current | An entry in docsRphyRpdIfRpdEnetToCoreEntityMapTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.5.1.1 | ColumndocsRphyRpdIfRpdEnetToCoreEntityMapEntityIndex | read-only | current | The value of this attribute matches the value of the EntityIndex for the instance of Entity that reports the RPD Ethernet port signaled in GCP with EnetPortInd… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.6 | TabledocsRphyRpdIfCoreToRpdMapTable | not-accessible | current | This table maps certain CCAP Core ifTable interfaces identified with an ifIndex to an RPD interface identified in GCP. See the reference for additional require… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.6.1 | RowdocsRphyRpdIfCoreToRpdMapEntry | not-accessible | current | An entry in docsRphyRpdIfCoreToRpdMapTable. An entry exists for each RPD interface directly represented in the CCAP ifTable. The IfIndex corresponds to a CCAP … |
| 1.3.6.1.4.1.4491.2.1.30.1.2.6.1.1 | ColumndocsRphyRpdIfCoreToRpdMapRpdCoreIndex | not-accessible | current | This key attribute selects the CCAP Core IfIndex for the RPD Interface identified in GCP. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.6.1.2 | ColumndocsRphyRpdIfCoreToRpdMapRpdUniqueId | not-accessible | current | This key attribute is the MAC address selecting a particular CIN facing Ethernet port. The value of this attribute matches the value of the RpdUniqueId attribu… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.6.1.3 | ColumndocsRphyRpdIfCoreToRpdMapRpdRfPortDirection | not-accessible | current | This key attribute selects the direction of an RF port, which together with RpdRfPortIndex uniquely identifies an RF port on the RPD. The RF port direction is … |
| 1.3.6.1.4.1.4491.2.1.30.1.2.6.1.4 | ColumndocsRphyRpdIfCoreToRpdMapRpdRfPortIndex | not-accessible | current | This key attribute selects a specific RF port on an RPD, which together with RpdRfPortDirection uniquely identifies an RF port on the RPD. The value matches th… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.6.1.5 | ColumndocsRphyRpdIfCoreToRpdMapRpdRfChanType | read-only | current | For RF channel interfaces, This attribute reports the type of the channel as signaled in the GCP RfChannelType TLV 12.2. For RF port interfaces, this attribute… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.6.1.6 | ColumndocsRphyRpdIfCoreToRpdMapRpdRfChanIndex | read-only | current | For interfaces corresponding to RF channels, this attribute reports the channel of the type specified in RpdRfChannelType, and matches the value signaled in th… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.7 | TabledocsRphyRpdIfRpdToCoreMapTable | not-accessible | current | This table maps certain RPD interface identified via GCP integers to an ifIndex reported by the CCAP Core. This table instruments the same information as the d… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.7.1 | RowdocsRphyRpdIfRpdToCoreMapEntry | not-accessible | current | An entry in docsRphyRpdIfRpdToCoreMapTable. An entry exists for each RPD interface directly represented in the CCAP ifTable. The index 'CoreIfIndex' correspond… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.7.1.1 | ColumndocsRphyRpdIfRpdToCoreMapRpdRfPortDirection | not-accessible | current | This attribute reports the direction of an RF port, which together with RpdRfPortIndex uniquely identifies an RF port on the RPD. The RF port direction is sign… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.7.1.2 | ColumndocsRphyRpdIfRpdToCoreMapRpdRfPortIndex | not-accessible | current | This attribute reports the Index of an RF port on an RPD, which together with RpdRfPortDirection uniquely identifies an RF port on the RPD. The value matches t… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.7.1.3 | ColumndocsRphyRpdIfRpdToCoreMapRpdRfChanType | not-accessible | current | For RF channel interfaces, This attribute reports the type of the channel as signaled in the GCP 'RfChannelType' TLV 12.2. For RF port interfaces, this attribu… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.7.1.4 | ColumndocsRphyRpdIfRpdToCoreMapRpdRfChanIndex | not-accessible | current | For interfaces corresponding to RF channels, this attribute reports the channel of the type specified in RpdRfChannelType, and matches the value signaled in th… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.7.1.5 | ColumndocsRphyRpdIfRpdToCoreMapCoreIfIndex | read-only | current | This key attribute reports the CCAP Core IfIndex for the RPD Interface identified in GCP. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8 | TabledocsRphyRpdIfEnetSfpPlusStatusTable | not-accessible | current | This table provides detailed information about the SFP+ transceivers on the RPD Ethernet Interfaces. It is intended to convey information available from Digita… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1 | RowdocsRphyRpdIfEnetSfpPlusStatusEntry | not-accessible | current | An entry containing information about the SFP+ pluggable transceiver on an RPD Ethernet Interface. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.1 | ColumndocsRphyRpdIfEnetSfpPlusStatusStatus | read-only | current | This attribute reports the current state of the SFP+ transceiver. The following state information can be reported: unknown: The state is unknown. notInstalled:… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.2 | ColumndocsRphyRpdIfEnetSfpPlusStatusIdentifier | read-only | current | This attribute is used to report the type of the serial transceiver. The following identifier types can be reported: unknown: unknown identifier gbic: Gigabit … |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.3 | ColumndocsRphyRpdIfEnetSfpPlusStatusExtendedIdentifier | read-only | current | This attribute reports the extended identifier of the type of serial transceiver. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.4 | ColumndocsRphyRpdIfEnetSfpPlusStatusConnectorType | read-only | current | This attribute reports the code for connector type of the transceiver. Enum values 128 - 255 are reserved for vendor specific connector types. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.5 | ColumndocsRphyRpdIfEnetSfpPlusStatusTransceiverComplianceCodes | read-only | current | This attribute reports bit significant indicators which define the electronic or optical interfaces that are supported by the transceiver. Reference [SFF 8472] |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.6 | ColumndocsRphyRpdIfEnetSfpPlusStatusTransceiverComplianceCode36 | read-only | current | This attribute reports the code for electronic or optical compatibility. Reference [SFF 8472], Transceiver Compliance Codes table. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.7 | ColumndocsRphyRpdIfEnetSfpPlusStatusEncoding | read-only | current | This attribute reports the code for high speed serial encoding algorithm. Reference [SFF 8024]. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.8 | ColumndocsRphyRpdIfEnetSfpPlusStatusBitRateNominal | read-only | current | This attribute reports nominal signaling rate in units of 100s of Mega Baud. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.9 | ColumndocsRphyRpdIfEnetSfpPlusStatusRateIdentifier | read-only | current | This attribute refers to several (optional) industry standard definitions of Rate Select or Application Select control behaviors, intended to manage transceive… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.10 | ColumndocsRphyRpdIfEnetSfpPlusStatusLengthKm | read-only | current | This attribute reports the link length that is supported by the transceiver while operating in compliance with the applicable standards using single mode fiber… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.11 | ColumndocsRphyRpdIfEnetSfpPlusStatusLength100M | read-only | current | This attribute reports the link length that is supported by the transceiver while operating in compliance with the applicable standards using single mode fiber… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.12 | ColumndocsRphyRpdIfEnetSfpPlusStatusLength50Mi10M | read-only | current | This attribute reports link length that is supported by the transceiver while operating in compliance with applicable standards using 50 micron multimode OM2 [… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.13 | ColumndocsRphyRpdIfEnetSfpPlusStatusLength62Pt5Mi10M | read-only | current | This attribute reports link length that is supported by the transceiver while operating in compliance with applicable standards using 62.5 micron multimode OM1… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.14 | ColumndocsRphyRpdIfEnetSfpPlusStatusLengthCopperM | read-only | current | This attribute reports minimum link length supported by the transceiver while operating in compliance with applicable standards using copper cable. For active … |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.15 | ColumndocsRphyRpdIfEnetSfpPlusStatusLength50MiOm3 | read-only | current | This attribute reports link length that is supported by the transceiver while operating in compliance with applicable standards using 50 micron multimode OM3 [… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.16 | ColumndocsRphyRpdIfEnetSfpPlusStatusVendorName | read-only | current | The vendor name is a 16 character string that contains ASCII characters, left-aligned and padded on the right with ASCII spaces (0x20). |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.17 | ColumndocsRphyRpdIfEnetSfpPlusStatusVendorOui | read-only | current | The vendor organizationally unique identifier (vendor OUI) is a 3-byte hexbinary string that contains the IEEE Company Identifier for the vendor. A value of al… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.18 | ColumndocsRphyRpdIfEnetSfpPlusStatusVendorPartNum | read-only | current | The vendor part number is a 16-byte ASCII string, left-aligned and padded on the right with ASCII spaces (0x20), defining the vendor part number or product nam… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.19 | ColumndocsRphyRpdIfEnetSfpPlusStatusVendorSerialNum | read-only | current | The vendor serial number is a 16-character ASCII string, left-aligned and padded on the right with ASCII spaces (0x20), defining the vendor's serial number for… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.20 | ColumndocsRphyRpdIfEnetSfpPlusStatusVendorRev | read-only | current | The vendor revision number is a 4-byte ASCII string, left-aligned and padded on the right with ASCII spaces (0x20), defining the vendor's product revision numb… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.21 | ColumndocsRphyRpdIfEnetSfpPlusStatusLaserWavelength | read-only | current | For optical variants, as defined by TransceiverComplianceCodes attribute, this attribute denotes nominal transmitter output wavelength at room temperature. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.22 | ColumndocsRphyRpdIfEnetSfpPlusStatusOptions | read-only | current | This attribute reports options implemented in the transceiver as described in the Options Values table of [SFF 8472]. The following rate identifier types can b… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.23 | ColumndocsRphyRpdIfEnetSfpPlusStatusBitRateMax | read-only | current | This attribute reports the upper bit rate limit at which the transceiver will still meet its specifications. This attribute is specified in units of 1% above t… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.24 | ColumndocsRphyRpdIfEnetSfpPlusStatusBitRateMin | read-only | current | This attribute reports the lower bit rate limit at which the transceiver will still meet its specifications and is specified in units of 1% below the nominal b… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.25 | ColumndocsRphyRpdIfEnetSfpPlusStatusVendorDate | read-only | current | This attribute is a 6-byte field that contains the vendor's date code in ASCII characters. The date code is specified in the following format: Bytes 0, 1 - ASC… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.26 | ColumndocsRphyRpdIfEnetSfpPlusStatusVendorSpecificLotCode | read-only | current | This attribute reports a vendor specific lot code. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.27 | ColumndocsRphyRpdIfEnetSfpPlusStatusDiagMonitorType | read-only | current | This attribute reports how diagnostic monitoring is implemented in the selected transceiver. The following diagnostic monitoring types can be reported: unalloc… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.28 | ColumndocsRphyRpdIfEnetSfpPlusStatusEnhancedOptions | read-only | current | This attribute reports the optional digital diagnostic features implemented in the transceiver. The following values enhanced options types can be reported: un… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.29 | ColumndocsRphyRpdIfEnetSfpPlusStatusSff8472Compliance | read-only | current | This attribute reports which feature set(s) are implemented in the transceiver. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.30 | ColumndocsRphyRpdIfEnetSfpPlusStatusVendorSpecificData | read-only | current | This attribute reports a 32-byte long hexbinary string with content of Vendor Specific EEPROM (address 0xA0, bytes 96-127). |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.31 | ColumndocsRphyRpdIfEnetSfpPlusStatusMeasuredTxOutputPwr | read-only | current | This attribute reports measured transmit output power in units of 0.1 micro Watts. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.32 | ColumndocsRphyRpdIfEnetSfpPlusStatusMeasuredRxInputPwr | read-only | current | This attribute reports measured received optical power in units of 0.1 micro Watts. The reported value can represent either average received power or OMA (Opti… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.33 | ColumndocsRphyRpdIfEnetSfpPlusStatusDigitalDiagA2Info | read-only | current | This attribute reports diagnostics data fields from Address 0xA2 of the transceiver's two wire serial bus. The data is provided undecoded. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.34 | ColumndocsRphyRpdIfEnetSfpPlusStatusMeasuredTxBiasCurrent | read-only | current | This attribute, which is optional for SFP+ pluggable transceivers, reports measured transmit bias current in units of 2 micro Amps. If this attribute is not su… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.35 | ColumndocsRphyRpdIfEnetSfpPlusStatusMeasuredTemperature | read-only | current | This attribute, which is optional for SFP+ pluggable transceivers, reports internally measured transceiver temperature as a signed twos compliment value in inc… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.8.1.36 | ColumndocsRphyRpdIfEnetSfpPlusStatusMeasuredSupplyVoltage | read-only | current | This attribute, which is optional for SFP+ pluggable transceivers, reports internally measured transceiver supply voltage in units of 100 micro Volts. If this … |
| 1.3.6.1.4.1.4491.2.1.30.1.2.9 | TabledocsRphyRpdIfEnetSyncEPortStatusTable | not-accessible | current | The SyncEPortStatus provides the status of one RPD Ethernet port being used for SyncE. The CCAP Core MUST create a row in the SyncEPortStatus table for every I… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.9.1 | RowdocsRphyRpdIfEnetSyncEPortStatusEntry | not-accessible | current | An entry for a port being used for SyncE |
| 1.3.6.1.4.1.4491.2.1.30.1.2.9.1.1 | ColumndocsRphyRpdIfEnetSyncEPortStatusSignalQualified | read-only | current | This attribute is true if the signal on this Ethernet port is qualified for SyncE. It is false otherwise. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.9.1.2 | ColumndocsRphyRpdIfEnetSyncEPortStatusReceivedSsm | read-only | current | This attribute contains the SSM value received for the interface. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.10 | TabledocsRphyRpdIfRfmStatusTable | not-accessible | current | The RfmStatus table provides the status of one RPD RF module (RFM) of an optical node-based RPD. Shelf RPDs do not have RF modules. See the Remote PHY Node Arc… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.10.1 | RowdocsRphyRpdIfRfmStatusEntry | not-accessible | current | A row in the docsRphyRpdIfRfmStatusTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.10.1.1 | ColumndocsRphyRpdIfRfmStatusNodePortIndex | not-accessible | current | This attribute contains the RPD's RF module index (i.e., the node RF port). Numbers range from 0 to N-1, where N is the number reported by the RPD through the … |
| 1.3.6.1.4.1.4491.2.1.30.1.2.10.1.2 | ColumndocsRphyRpdIfRfmStatusReportedDsGain | read-only | current | This attribute is used to report DS gain in the RFM. RPDs with locally configured downstream gain (i.e., physical pads) can report the gain though this attribu… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.10.1.3 | ColumndocsRphyRpdIfRfmStatusReportedDsGainStatus | read-only | current | This attribute is used to report additional qualifying information about the value reported through ReportedDsGain (TLV 161.1.2) attribute. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.10.1.4 | ColumndocsRphyRpdIfRfmStatusReportedUsGain | read-only | current | This attribute is used to report upstream gain in the RFM. RPDs with locally configured upstream gain (i.e., physical pads) can report the gain though this att… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.10.1.5 | ColumndocsRphyRpdIfRfmStatusReportedUsGainStatus | read-only | current | This attribute is used to report addition qualifying information about the value reported through ReportedUsGain (TLV 161.1.4) attribute. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.10.1.6 | ColumndocsRphyRpdIfRfmStatusReportedRfmDsTilt | read-only | current | This attribute is used to report DS tilt in the RFM. RPDs with locally configured downstream tilt (i.e., physical pads) report the tilt though this attribute w… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.10.1.7 | ColumndocsRphyRpdIfRfmStatusReportedRfmDsTiltStatus | read-only | current | This attribute is used to report addition qualifying information about the value reported through ReportedRfmDsTilt (TLV 161.1.6) attribute. This attribute is … |
| 1.3.6.1.4.1.4491.2.1.30.1.2.10.1.8 | ColumndocsRphyRpdIfRfmStatusDsOutputPower | read-only | current | This attribute is used to report the output power for the selected node RF port of the RFM. RPDs with unknown DS RFM output power report a value of 0. |
| 1.3.6.1.4.1.4491.2.1.30.1.2.10.1.9 | ColumndocsRphyRpdIfRfmStatusUsExpectedRxPower | read-only | current | This attribute is used to report the expected input power for the selected node RF port of the RFM. RPDs with unknown upstream receive power level report a val… |
| 1.3.6.1.4.1.4491.2.1.30.1.2.10.1.10 | ColumndocsRphyRpdIfRfmStatusTotalDsTilt | read-only | current | This attribute is used to report the combined tilt value for the selected node RF port of the RFM. RPDs with unknown DS RFM tilt report a value of 0. |
| 1.3.6.1.4.1.4491.2.1.30.1.3 | NodedocsRphyRpdIpMibObjects | |||
| 1.3.6.1.4.1.4491.2.1.30.1.3.1 | TabledocsRphyRpdIpv4GrpTable | not-accessible | current | The table containing per-RPD IPv4-specific information. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.1.1 | RowdocsRphyRpdIpv4GrpEntry | not-accessible | current | An entry containing IPv4-specific information for a specific RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.1.1.1 | ColumndocsRphyRpdIpv4GrpDefaultTTL | read-only | current | The default value inserted into the Time-To-Live field of the IPv4 header of datagrams originated at this entity, whenever a TTL value is not supplied by the t… |
| 1.3.6.1.4.1.4491.2.1.30.1.3.1.1.2 | ColumndocsRphyRpdIpv4GrpInterfaceTableLastChange | read-only | current | This attribute reports the value of RpdSysUpTime on the most recent occasion at which an instance of the Ipv4Interface object was added or deleted, or when a R… |
| 1.3.6.1.4.1.4491.2.1.30.1.3.2 | TabledocsRphyRpdIpv6GrpTable | not-accessible | current | The table containing per-RPD IPv6-specific information. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.2.1 | RowdocsRphyRpdIpv6GrpEntry | not-accessible | current | An entry containing IPv6-specific information for a specific RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.2.1.1 | ColumndocsRphyRpdIpv6GrpIpDefaultHopLimit | read-only | current | The default value inserted into the Hop Limit field of the IPv6 header of datagrams originated at this entity whenever a Hop Limit value is not supplied by the… |
| 1.3.6.1.4.1.4491.2.1.30.1.3.2.1.2 | ColumndocsRphyRpdIpv6GrpInterfaceTableLastChange | read-only | current | This attribute reports the value of RpdSysUpTime on the most recent occasion at which an instance of the Ipv6Interface object was added or deleted or when a Re… |
| 1.3.6.1.4.1.4491.2.1.30.1.3.2.1.3 | ColumndocsRphyRpdIpv6GrpIfStatsTableLastChange | read-only | current | This attribute reports the value of RpdSysUpTime on the most recent occasion at which an instance of the ipIfStats object was added or deleted. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.3 | TabledocsRphyRpdIpv4InterfaceTable | not-accessible | current | The table containing per-interface IPv4-specific information. The CCAP Core reads the attributes of the Ipv4Interface table in the complex GCP TLV 100.12 |
| 1.3.6.1.4.1.4491.2.1.30.1.3.3.1 | RowdocsRphyRpdIpv4InterfaceEntry | not-accessible | current | An entry containing IPv4-specific information for an RPD's ethernet port. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.3.1.1 | ColumndocsRphyRpdIpv4InterfaceEnableStatus | read-only | current | The indication of whether IPv4 is enabled (up) or disabled (down) on this interface. This object does not affect the state of the interface itself, only its co… |
| 1.3.6.1.4.1.4491.2.1.30.1.3.3.1.2 | ColumndocsRphyRpdIpv4InterfaceRetransmitTime | read-only | current | The time between retransmissions of ARP requests to a neighbor when resolving the address or when probing the reachability of a neighbor. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.4 | TabledocsRphyRpdIpv6InterfaceTable | not-accessible | current | The table containing per-interface IPv6-specific information. The CCAP core reads the attributes of of an IPv6Interface object in GCP TLV 100.13. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.4.1 | RowdocsRphyRpdIpv6InterfaceEntry | not-accessible | current | An entry containing IPv6-specific information for an RPD's ethernet port. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.4.1.1 | ColumndocsRphyRpdIpv6InterfaceIdentifier | read-only | current | The Interface Identifier for this interface. The Interface Identifier is combined with an address prefix to form an interface address. By default, the Interfac… |
| 1.3.6.1.4.1.4491.2.1.30.1.3.4.1.2 | ColumndocsRphyRpdIpv6InterfaceEnableStatus | read-only | current | The indication of whether IPv6 is enabled (up) or disabled (down) on this interface. This object does not affect the state of the interface itself, only its co… |
| 1.3.6.1.4.1.4491.2.1.30.1.3.4.1.3 | ColumndocsRphyRpdIpv6InterfaceReachableTime | read-only | current | The time a neighbor is considered reachable after receiving a reachability confirmation. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.4.1.4 | ColumndocsRphyRpdIpv6InterfaceRetransmitTime | read-only | current | The time between retransmissions of Neighbor Solicitation messages to a neighbor when resolving the address or when probing the reachability of a neighbor. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.5 | TabledocsRphyRpdIpIfStatsTable | not-accessible | current | This table provides statistics for IP Packets sent or received by an RPD's own IP Address. It is modeled after the IP-MIB IpIfStatsTable described in RFC 4293;… |
| 1.3.6.1.4.1.4491.2.1.30.1.3.5.1 | RowdocsRphyRpdIpIfStatsEntry | not-accessible | current | An interface statistics entry containing objects for a particular interface and version of IP. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.1 | ColumndocsRphyRpdIpIfStatsIPVersion | not-accessible | current | This key attribute reports the IP version of this entry. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.2 | ColumndocsRphyRpdIpIfStatsInReceives | read-only | current | The total number of input IP datagrams received, including those received in error. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.3 | ColumndocsRphyRpdIpIfStatsInOctets | read-only | current | The total number of octets received in input IP datagrams, including those received in error. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.4 | ColumndocsRphyRpdIpIfStatsInHdrErrors | read-only | current | The number of input IP datagrams discarded due to errors in their IP headers, including version number mismatch, other format errors, hop count exceeded, error… |
| 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.5 | ColumndocsRphyRpdIpIfStatsInNoRoutes | read-only | current | The number of input IP datagrams discarded because no route could be found to transmit them to their destination. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.6 | ColumndocsRphyRpdIpIfStatsInAddrErrors | read-only | current | The number of input IP datagrams discarded because the IP address in their IP header's destination field was not a valid address to be received at this entity.… |
| 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.7 | ColumndocsRphyRpdIpIfStatsInUnknownProtos | read-only | current | The number of locally-addressed IP datagrams received successfully but discarded because of an unknown or unsupported protocol. When tracking interface statist… |
| 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.8 | ColumndocsRphyRpdIpIfStatsInTruncatedPkts | read-only | current | The number of input IP datagrams discarded because the datagram frame didn't carry enough data. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.9 | ColumndocsRphyRpdIpIfStatsInDiscards | read-only | current | The number of input IP datagrams for which no problems were encountered to prevent their continued processing, but were discarded (e.g., for lack of buffer spa… |
| 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.10 | ColumndocsRphyRpdIpIfStatsInDelivers | read-only | current | The total number of datagrams successfully delivered to IP user-protocols (including ICMP). |
| 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.11 | ColumndocsRphyRpdIpIfStatsOutRequests | read-only | current | The total number of IP datagrams that local IP user- protocols (including ICMP) supplied to IP in requests for transmission. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.12 | ColumndocsRphyRpdIpIfStatsOutDiscards | read-only | current | The number of output IP datagrams for which no problem was encountered to prevent their transmission to their destination, but were discarded (e.g., for lack o… |
| 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.13 | ColumndocsRphyRpdIpIfStatsOutTransmits | read-only | current | The total number of IP datagrams that this entity supplied to the lower layers for transmission. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.14 | ColumndocsRphyRpdIpIfStatsOutOctets | read-only | current | The total number of octets in IP datagrams delivered to the lower layers for transmission. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.15 | ColumndocsRphyRpdIpIfStatsInMcastPkts | read-only | current | The number of IP multicast datagrams received. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.16 | ColumndocsRphyRpdIpIfStatsInMcastOctets | read-only | current | The total number of octets received in IP multicast datagrams. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.17 | ColumndocsRphyRpdIpIfStatsOutMcastPkts | read-only | current | The number of IP multicast datagrams transmitted. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.18 | ColumndocsRphyRpdIpIfStatsOutMcastOctets | read-only | current | The total number of octets transmitted in IP multicast datagrams. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.19 | ColumndocsRphyRpdIpIfStatsDiscontinuityTime | read-only | current | This attribute reports the date and time at which any one or more of the counters in this group were created or last reset to zero. If the RPD does not acquire… |
| 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.20 | ColumndocsRphyRpdIpIfStatsRefreshRate | read-only | current | The minimum reasonable polling interval for this entry. This object provides an indication of the minimum amount of time required to update the counters in thi… |
| 1.3.6.1.4.1.4491.2.1.30.1.3.6 | TabledocsRphyRpdIpAddressTable | not-accessible | current | This table contains addressing information relevant to the RPD's interfaces. This table does not contain multicast address information. Note well: When instant… |
| 1.3.6.1.4.1.4491.2.1.30.1.3.6.1 | RowdocsRphyRpdIpAddressEntry | not-accessible | current | An address mapping for a particular interface. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.6.1.1 | ColumndocsRphyRpdIpAddressAddrType | not-accessible | current | The address type of docsRphyRpdIpAddressAddr. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.6.1.2 | ColumndocsRphyRpdIpAddressAddr | not-accessible | current | The IP address to which this entry's addressing information pertains. The address type of this object is specified in AddrType. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.6.1.3 | ColumndocsRphyRpdIpAddressEnetPortIndex | read-only | current | This attribute reports a unique index for this Ethernet port interface. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.6.1.4 | ColumndocsRphyRpdIpAddressType | read-only | current | The type of address. broadcast(3) is not a valid value for IPv6 addresses (RFC 3513). |
| 1.3.6.1.4.1.4491.2.1.30.1.3.6.1.5 | ColumndocsRphyRpdIpAddressPrefixLen | read-only | current | This attribute reports the prefix length associated with this address. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.6.1.6 | ColumndocsRphyRpdIpAddressOrigin | read-only | current | The origin of the address. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.6.1.7 | ColumndocsRphyRpdIpAddressStatus | read-only | current | The status of the address, describing if the address can be used for communication. In the absence of other information, an IPv4 address is always preferred(1). |
| 1.3.6.1.4.1.4491.2.1.30.1.3.6.1.8 | ColumndocsRphyRpdIpAddressCreated | read-only | current | The value of sysUpTime at the time this entry was created. If this entry was created prior to the last re- initialization of the local network management subsy… |
| 1.3.6.1.4.1.4491.2.1.30.1.3.6.1.9 | ColumndocsRphyRpdIpAddressLastChanged | read-only | current | The value of sysUpTime at the time this entry was last updated. If this entry was updated prior to the last re- initialization of the local network management … |
| 1.3.6.1.4.1.4491.2.1.30.1.3.7 | TabledocsRphyRpdIpNetToPhysicalTable | not-accessible | current | The IP Address Translation table used for mapping from IP addresses to physical addresses. The Address Translation tables contain the IP address to 'physical' … |
| 1.3.6.1.4.1.4491.2.1.30.1.3.7.1 | RowdocsRphyRpdIpNetToPhysicalEntry | not-accessible | current | Each entry contains one IP address to 'physical' address equivalence. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.7.1.1 | ColumndocsRphyRpdIpNetToPhysicalNetAddressType | not-accessible | current | The type of NetAddress. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.7.1.2 | ColumndocsRphyRpdIpNetToPhysicalNetAddress | not-accessible | current | The IP Address corresponding to the media-dependent 'physical' address. The address type of this object is specified in AddressType. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.7.1.3 | ColumndocsRphyRpdIpNetToPhysicalPhysAddress | read-only | current | The media-dependent 'physical' address. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.7.1.4 | ColumndocsRphyRpdIpNetToPhysicalLastUpdated | read-only | current | This attribute reports the value of RpdSysUpTime at the time this entry was last updated. If this entry was updated prior to the last re-initialization of the … |
| 1.3.6.1.4.1.4491.2.1.30.1.3.7.1.5 | ColumndocsRphyRpdIpNetToPhysicalType | read-only | current | The type of mapping. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stati… |
| 1.3.6.1.4.1.4491.2.1.30.1.3.7.1.6 | ColumndocsRphyRpdIpNetToPhysicalState | read-only | current | The Neighbor Unreachability Detection state for the interface when the address mapping in this entry is used. If Neighbor Unreachability Detection is not in us… |
| 1.3.6.1.4.1.4491.2.1.30.1.3.8 | TabledocsRphyRpdIpDefaultRouterTable | not-accessible | current | The table used to describe the default routers known to the RPD. The CCAP Core reads all attributes of an IpDefaultRouter object with complex GCP TLV Type 100.… |
| 1.3.6.1.4.1.4491.2.1.30.1.3.8.1 | RowdocsRphyRpdIpDefaultRouterEntry | not-accessible | current | Each entry contains information about a default router known to the RPD. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.8.1.1 | ColumndocsRphyRpdIpDefaultRouterAddressType | not-accessible | current | This key attribute reports the type of IP address in the Address attribute. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.8.1.2 | ColumndocsRphyRpdIpDefaultRouterAddress | not-accessible | current | The IP address of the default router represented by this row. The address type of this object is specified in AddressType. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.8.1.3 | ColumndocsRphyRpdIpDefaultRouterLifetime | read-only | current | The remaining length of time, in seconds, that this router will continue to be useful as a default router. A value of zero indicates that it is no longer usefu… |
| 1.3.6.1.4.1.4491.2.1.30.1.3.8.1.4 | ColumndocsRphyRpdIpDefaultRouterPreference | read-only | current | An indication of preference given to this router as a default router as described in the Default Router Preferences document. Treating the value as a 2 bit sig… |
| 1.3.6.1.4.1.4491.2.1.30.1.3.9 | NodedocsRphyRpdIpIcmpMibObjects | |||
| 1.3.6.1.4.1.4491.2.1.30.1.3.9.1 | TabledocsRphyRpdIpIcmpMsgStatsTable | not-accessible | current | The table of system-wide per-version, per-message type ICMP counters. The CCAP Core reads all attributes of an IcmpMsgStats object with complex GCP TLV 100.19. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.9.1.1 | RowdocsRphyRpdIpIcmpMsgStatsEntry | not-accessible | current | A conceptual row in the docsRphyRpdIpIcmpMsgStatsTable. The system should track each ICMP type value, even if that ICMP type is not supported by the system. Ho… |
| 1.3.6.1.4.1.4491.2.1.30.1.3.9.1.1.1 | ColumndocsRphyRpdIpIcmpMsgStatsIPVersion | not-accessible | current | The IP version of the statistics. Statistics are provided for each IP version supported. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.9.1.1.2 | ColumndocsRphyRpdIpIcmpMsgStatsType | not-accessible | current | The ICMP type field of the message type being counted by this row. Note that ICMP message types are scoped by the address type in use. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.9.1.1.3 | ColumndocsRphyRpdIpIcmpMsgStatsInPkts | read-only | current | The number of input packets for this AF and type. |
| 1.3.6.1.4.1.4491.2.1.30.1.3.9.1.1.4 | ColumndocsRphyRpdIpIcmpMsgStatsOutPkts | read-only | current | The number of output packets for this AF and type. |
| 1.3.6.1.4.1.4491.2.1.30.1.4 | NodedocsRphyCcapMibObjects | |||
| 1.3.6.1.4.1.4491.2.1.30.1.4.1 | TabledocsRphyCcapL2tpSessionInfoTable | not-accessible | current | This table provides details for every session that terminates at the CCAP Core from the CCAP Core's point of view. There will be multiple sessions for each RPD… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.1.1 | RowdocsRphyCcapL2tpSessionInfoEntry | not-accessible | current | The conceptual row of docsRphyCcapL2tpSessionInfoTable. A row entry is created for every session the CCAP-Core terminates. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.1 | ColumndocsRphyCcapL2tpSessionInfoSessionIpAddrType | not-accessible | current | This key attribute indicates whether the IP address provided in the CcapLcceIpAddress and RpdLcceIpAddr attributes are IPv4 or IPv6. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.2 | ColumndocsRphyCcapL2tpSessionInfoCcapLcceIpAddr | not-accessible | current | This key attribute provides the LCCE IP address on the CCAP Core of the session detailed in the instance. As reported by the RPD for a static multicast session… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.3 | ColumndocsRphyCcapL2tpSessionInfoRpdLcceIpAddr | not-accessible | current | This key attribute reports the remote-side RPD LCCE IP address of the session detailed in the instance. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.4 | ColumndocsRphyCcapL2tpSessionInfoDirection | not-accessible | current | This key attribute reports the direction of the session detailed in the instance. Valid values include: 'forward' - Forward (downstream) direction toward the R… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.5 | ColumndocsRphyCcapL2tpSessionInfoL2tpSessionId | not-accessible | current | This key attribute reports the value of the L2TPv3 session ID transmitted or received on the session. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.6 | ColumndocsRphyCcapL2tpSessionInfoCoreId | read-only | current | This attribute reports the unique identifier, for example a MAC address, of the CCAP Core with which this session terminates. The CCAP Core sends its unique id… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.7 | ColumndocsRphyCcapL2tpSessionInfoConnCtrlID | read-only | current | This attribute indicates the control connection identifier (CCID) for this session. This attribute is zero for static sessions, since static sessions are not p… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.8 | ColumndocsRphyCcapL2tpSessionInfoUdpPort | read-only | current | This attribute provides the UDP Port reported by the CCAP Core when the DEPI session uses L2TPv3 Header Over UDP. This attribute reports a value of 0 when the … |
| 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.9 | ColumndocsRphyCcapL2tpSessionInfoDescr | read-only | current | This attribute provides an ASCII string constructed with the form: RemoteEndId=(pp:mmm:ccc), ... { repeated for multiple endpoints } where pp is the 0-based po… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.10 | ColumndocsRphyCcapL2tpSessionInfoSessionType | read-only | current | This attribute specifies whether the session is an MPT session or PSP session. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.11 | ColumndocsRphyCcapL2tpSessionInfoSessionSubType | read-only | current | This attribute specifies the type of DEPI MPT or DEPI PSP session. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.12 | ColumndocsRphyCcapL2tpSessionInfoMaxPayload | read-only | current | This attribute indicates the maximum MTU negotiated between the CCAP Core and the RPD during the session establishment process. The MTU is the layer 3 payload … |
| 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.13 | ColumndocsRphyCcapL2tpSessionInfoPathPayload | read-only | current | This attribute indicates the maximum MTU traversing the CIN from CCAP Core to the RPD. This is calculated by the CCAP Core by procedures such as MTU discovery … |
| 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.14 | ColumndocsRphyCcapL2tpSessionInfoRpdIfMtu | read-only | current | This attribute provides the RPD's CIN interface MTU and is read as the value of the following L2TPV3 AVP transmitted by the RPD during session setup: DEPI Down… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.15 | ColumndocsRphyCcapL2tpSessionInfoCoreIfMtu | read-only | current | This attribute provides the CCAP Core's CIN interface MTU and is read as the value of the following L2TPv3 AVP as received by the device during session setup: … |
| 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.16 | ColumndocsRphyCcapL2tpSessionInfoIncludeDOCSISMsgs | read-only | current | This attribute returns true if the CCAP Core includes DOCSIS MAP messages and other MAC Management messages in the interface entry associated with this control… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.17 | ColumndocsRphyCcapL2tpSessionInfoErrorCode | read-only | current | The error code raised when the session is in an error state. 'invalidMACInterfaceValue' Indicates wrong assignment of the CCAP Core MAC interface ifIndex. 'inv… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.18 | ColumndocsRphyCcapL2tpSessionInfoCreationTime | read-only | current | The attribute contains the sysUptime when the entry was turned active. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.19 | ColumndocsRphyCcapL2tpSessionInfoOperStatus | read-only | current | This attribute provides the current status of the pseudowire from the point of view of the specific reporting entity (CCAP-Core). For static psuedowires, the o… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.20 | ColumndocsRphyCcapL2tpSessionInfoLocalStatus | read-only | current | The attribute provides the status of the pseudowire in the local node. If the 'other' bit is set, it indicates that an additional vendor-specific status is rep… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.21 | ColumndocsRphyCcapL2tpSessionInfoLastChange | read-only | current | The attribute provides the value of sysUpTime when the session entered its current OperStatus state from the point of view of the specific reporting entity (CC… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.22 | ColumndocsRphyCcapL2tpSessionInfoExtendedRemoteEndId | read-only | current | This attribute provides an ASCII string constructed with the form: RemoteEndId=(pp:mmm:ccc),... { repeated for multiple channels } where pp is the zero-based p… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.2 | TabledocsRphyCcapL2tpSessionFlowTable | not-accessible | current | This table represents a PSP Flow of L2TP session or for those sessions, which do not have PSP Flows, represents entire session. In the latter case the PSP Flow… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.2.1 | RowdocsRphyCcapL2tpSessionFlowEntry | not-accessible | current | The conceptual row of docsRphyCcapL2tpSessionFlowTable. This is an extension to docsRphyCcapL2tpSessionInfoTable for the CCAP Core. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.2.1.1 | ColumndocsRphyCcapL2tpSessionFlowPspFlowId | not-accessible | current | This key attribute identifies a PSP Flow within the session. For MPT sessions and for PSP sessions which do not support multiple PSP Flows, this attribute is z… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.2.1.2 | ColumndocsRphyCcapL2tpSessionFlowPhbId | read-only | current | This attribute reports the Per Hop Behavior Identifier that equals the 6-bit DSCP with which the CCAP Core transmits downstream L2TPv3 data packets for the flo… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.3 | TabledocsRphyCcapL2tpSessionStatsTable | not-accessible | current | This table provides statistics for every session that terminates at the CCAP-Core from the CCAP Core's point of view. It also provides statistics about each tu… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.3.1 | RowdocsRphyCcapL2tpSessionStatsEntry | not-accessible | current | The conceptual row of docsRphyCcapL2tpSessionStatsTable. This table is an augmentation of docsRphyCcapL2tpSessionFlowTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.3.1.1 | ColumndocsRphyCcapL2tpSessionStatsOutOfSeqPkts | read-only | current | This attribute indicates the count of session packets that were received out of sequence from the point of view of the reporting entity. It is vendor dependent… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.3.1.2 | ColumndocsRphyCcapL2tpSessionStatsInPkts | read-only | current | This attribute counts the number of received packets accepted for processing above the L2TPv3 protocol layer. The InPackets attribute count excludes packets dr… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.3.1.3 | ColumndocsRphyCcapL2tpSessionStatsInDiscards | read-only | current | This attribute counts the number of received packets discarded by the L2TPv3 protocol layer itself, including those discarded because they were out of sequence… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.3.1.4 | ColumndocsRphyCcapL2tpSessionStatsOutPkts | read-only | current | This attribute counts the number of packets conceptually attempted to be transmitted from above the L2TPv3 protocol layer. The OutPackets attribute counts pack… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.3.1.5 | ColumndocsRphyCcapL2tpSessionStatsOutErrors | read-only | current | This attribute counts the number of packets attempted to be transmitted from above the L2TPv3 protocol layer that could not be transmitted below the L2TPv3 pro… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.4 | TabledocsRphyCcapCinDsLatencyTable | not-accessible | current | This table provides measurements on the latency on the CIN link for the session as measured by the CCAP-Core. These measurements are based on the DEPI latency … |
| 1.3.6.1.4.1.4491.2.1.30.1.4.4.1 | RowdocsRphyCcapCinDsLatencyEntry | not-accessible | current | The conceptual row of docsRphyCcapCinLatencyTable. A row entry is created for every session the CCAP Core terminates. This table is an augmentation of docsRphy… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.4.1.1 | ColumndocsRphyCcapCinDsLatencyLastVal | read-only | current | This attribute indicates the latest latency measurement on this session. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.4.1.2 | ColumndocsRphyCcapCinDsLatencyLastValTime | read-only | current | This attribute indicates the sysUpTime value of the last time the docsRphyCcapCinLatencyPerfLastVal attribute was updated. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.4.1.3 | ColumndocsRphyCcapCinDsLatencyInterval | read-only | current | This attribute provides the time interval used to measure periodically the CIN latency per DEPI session. Active measurement of CIN latency applies to active DE… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.5 | TabledocsRphyCcapSessionCinDsLatencyStatsTable | not-accessible | current | This table provides sequence of recent measurements of the CIN latency on the network as measured by the CCAP Core. When the table is full, the oldest measurem… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.5.1 | RowdocsRphyCcapSessionCinDsLatencyStatsEntry | not-accessible | current | The conceptual row of docsRphyCcapSessionCinDsLatencyStatsTable. A row entry is created for every session the CCAP Core terminates. This is an extension to doc… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.5.1.1 | ColumndocsRphyCcapSessionCinDsLatencyStatsIntervalSeq | not-accessible | current | This attribute indicates the interval sequence where the CIN latency measurement was taken. It is valid in an implementation that overrides the oldest sequence… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.5.1.2 | ColumndocsRphyCcapSessionCinDsLatencyStatsVal | read-only | current | This attribute indicates the CIN latency value measured for the session referenced by this entry. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.5.1.3 | ColumndocsRphyCcapSessionCinDsLatencyStatsValTime | read-only | current | This attribute provides the sysUpTime value for the last time docsRphyCcapCinLatencyPerfVal was updated. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.6 | TabledocsRphyCcapCwToneStatusTable | not-accessible | current | This table has one entry for each CW tone configured on a downstream RF port on an RPD. The status of the tone depends on whether the tone has been successfull… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.6.1 | RowdocsRphyCcapCwToneStatusEntry | not-accessible | current | The conceptual row of docsRphyCcapCwToneStatusTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.6.1.1 | ColumndocsRphyCcapCwToneStatusRfPort | not-accessible | current | This attribute identifies the RF port for the CW tone. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.6.1.2 | ColumndocsRphyCcapCwToneStatusFrequency | not-accessible | current | This attribute identifies the CW tone on an RF port on the RPD, as found either in the CwTonesCfg table, if present for this RPD, or in DefaultCwTonesCfg table. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.6.1.3 | ColumndocsRphyCcapCwToneStatusStatus | read-only | current | This attribute provides the status of the tone on the parent RPD. If the RPD is not connected, or it is connected, but tone configuration has not been done yet… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.7 | TabledocsRphyCcapUsOfdmaFdxEcStatusTable | not-accessible | current | This table provides status information about CCAP Core's support for RPD echo canceler training protocol. A CCAP Core supports a row in this table for every FD… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.7.1 | RowdocsRphyCcapUsOfdmaFdxEcStatusEntry | not-accessible | current | The conceptual row of docsRphyCcapUsOfdmaFdxEcStatusTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.7.1.1 | ColumndocsRphyCcapUsOfdmaFdxEcStatusCurrentEctPeriod | read-only | current | This attribute reports the current echo cancelation training period for the channel. The CCAP Core reports zero if no ECTO has been scheduled yet. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.7.1.2 | ColumndocsRphyCcapUsOfdmaFdxEcStatusCurrentEctoDuration | read-only | current | This attribute reports the current echo cancelation training opportunity duration for the channel. The CCAP Core reports zero if no ECTO has been scheduled yet. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.7.1.3 | ColumndocsRphyCcapUsOfdmaFdxEcStatusLastRequestEctPeriod | read-only | current | This attribute reports the last cancelation training period requested by the RPD for the channel. The CCAP Core reports zero if no ECT request has been receive… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.7.1.4 | ColumndocsRphyCcapUsOfdmaFdxEcStatusLastRequestEctoDuration | read-only | current | This attribute reports the last cancelation training opportunity duration requested by the RPD for the channel. The CCAP Core reports zero if no ECT request ha… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.7.1.5 | ColumndocsRphyCcapUsOfdmaFdxEcStatusNumTxEctos | read-only | current | This attribute reports the number of transmitted echo canceller training opportunities for the channel. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.7.1.6 | ColumndocsRphyCcapUsOfdmaFdxEcStatusNumRxEcRequestBlocks | read-only | current | This attribute reports the number of received echo canceller request blocks for the channel. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.7.1.7 | ColumndocsRphyCcapUsOfdmaFdxEcStatusNumRxEcRequestBlocksNoConv | read-only | current | This attribute reports the number of received echo canceller request blocks with indication of loss of EC convergence for the channel. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.8 | NodedocsRphyCcapTrfStats | |||
| 1.3.6.1.4.1.4491.2.1.30.1.4.8.1 | ScalardocsRphyCcapTrfStatsTunnelReplacements | read-only | current | This attribute counts the number of tunnels successfully replaced by the CCAP Core as a result of the transmission of an SCCRQ containing a DEPI Replaced Tunne… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.8.2 | ScalardocsRphyCcapTrfStatsTunnelReplacementFailures | read-only | current | This attribute counts the number of tunnel replacement attempts, following the transmission of an SCCRQ containing a DEPI Replaced Tunnel ID AVP by the CCAP Co… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.8.3 | ScalardocsRphyCcapTrfStatsTunnelHandovers | read-only | current | This attribute counts the number of tunnels transitioned from Standby to InService HA state as a result of the transmission of a DTU message by the CCAP Core. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.9 | TabledocsRphyCcapLcceStatsTable | not-accessible | current | This table is supported by the CCAP Core and is used to report on the DEPI L2TPv3 control connection activity between the Core and all the RPDs with which the … |
| 1.3.6.1.4.1.4491.2.1.30.1.4.9.1 | RowdocsRphyCcapLcceStatsEntry | not-accessible | current | The conceptual row of docsRphyCcapLcceStatsTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.9.1.1 | ColumndocsRphyCcapLcceStatsLcceIpAddrType | not-accessible | current | This key attribute indicates whether the IP address provided in the CcapLcceIpAddr and RpdLcceIpAddr attributes are IPv4 or IPv6. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.9.1.2 | ColumndocsRphyCcapLcceStatsCcapLcceIpAddr | not-accessible | current | This key attribute provides the LCCE IP address on the CCAP Core detailed in the instance. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.9.1.3 | ColumndocsRphyCcapLcceStatsRpdLcceIpAddr | not-accessible | current | This key attribute reports the RPD LCCE IP address detailed in the instance. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.9.1.4 | ColumndocsRphyCcapLcceStatsCoreId | read-only | current | This attribute reports the unique identifier of the CCAP Core. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.9.1.5 | ColumndocsRphyCcapLcceStatsCtrlConnEst | read-only | current | This attribute counts the number of DEPI control connections successfully established between the RPD and CCAP Core LCCEs. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.9.1.6 | ColumndocsRphyCcapLcceStatsCtrlConnEstFailures | read-only | current | This attribute counts the number of DEPI control connections that failed during establishment between the RPD and CCAP Core LCCEs. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.9.1.7 | ColumndocsRphyCcapLcceStatsCtrlConnFailures | read-only | current | This attribute counts the number of DEPI control connections between the RPD and CCAP Core LCCEs in which a failure was detected (after successful connection e… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.9.1.8 | ColumndocsRphyCcapLcceStatsCurrCtrlConn | read-only | current | This attribute counts the number of DEPI control connections that are currently operational between the RPD and CCAP Core LCCEs (i.e connections that are in an… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.10 | TabledocsRphyCcapCurrCtrlConnTable | not-accessible | current | This object is supported by the CCAP Core and is used to report on the currently operational DEPI L2TPv3 control connections on the CCAP Core. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.10.1 | RowdocsRphyCcapCurrCtrlConnEntry | not-accessible | current | The conceptual row of docsRphyCcapCurrCtrlConnTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.10.1.1 | ColumndocsRphyCcapCurrCtrlConnLcceIpAddrType | not-accessible | current | This key attribute indicates whether the IP address provided in the CcapLcceIpAddr and RpdLcceIpAddr attributes are IPv4 or IPv6. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.10.1.2 | ColumndocsRphyCcapCurrCtrlConnCcapLcceIpAddr | not-accessible | current | This key attribute provides the LCCE IP address on the CCAP Core of the control connection detailed in the instance. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.10.1.3 | ColumndocsRphyCcapCurrCtrlConnRpdLcceIpAddr | not-accessible | current | This key attribute reports the RPD LCCE IP address of the control connection detailed in the instance. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.10.1.4 | ColumndocsRphyCcapCurrCtrlConnCoreConnCtrlId | not-accessible | current | This key attribute reports the Core control connection identifier (CCID) for this control connection. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.10.1.5 | ColumndocsRphyCcapCurrCtrlConnRpdConnCtrlId | read-only | current | This attribute reports the RPD control connection identifier (CCID) for this control connection. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.10.1.6 | ColumndocsRphyCcapCurrCtrlConnCoreId | read-only | current | This attribute reports the unique identifier of the CCAP Core with which this control connection terminates. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.10.1.7 | ColumndocsRphyCcapCurrCtrlConnUdpPort | read-only | current | This attribute reports the UDP Port reported by the RPD when the DEPI control connection uses L2TPv3 Header Over UDP. This attribute reports a value of 0 when … |
| 1.3.6.1.4.1.4491.2.1.30.1.4.10.1.8 | ColumndocsRphyCcapCurrCtrlConnHaState | read-only | current | This attribute indicates the current HaState of the tunnel for which this DEPI control connection provides the signaling. If TRF is not supported by either the… |
| 1.3.6.1.4.1.4491.2.1.30.1.4.10.1.9 | ColumndocsRphyCcapCurrCtrlConnSessEstFailures | read-only | current | This attribute counts the number of DEPI sessions that failed during establishment using this control connection. |
| 1.3.6.1.4.1.4491.2.1.30.1.4.10.1.10 | ColumndocsRphyCcapCurrCtrlConnSessFailed | read-only | current | This attribute counts the number of DEPI sessions in which a failure was detected (after successful tunnel establishment) that led to the session being closed … |
| 1.3.6.1.4.1.4491.2.1.30.1.4.10.1.11 | ColumndocsRphyCcapCurrCtrlConnCurrSess | read-only | current | This attribute counts the number of current DEPI sessions using this control connection (i.e., sessions that are in an inService or standby state). Sessions th… |
| 1.3.6.1.4.1.4491.2.1.30.1.5 | NodedocsRphyCcapSecMibObjects | |||
| 1.3.6.1.4.1.4491.2.1.30.1.6 | NodedocsRphyCmtsCmStatMibObjects | |||
| 1.3.6.1.4.1.4491.2.1.30.1.6.1 | TabledocsRphyCmtsCmRegStatusTable | not-accessible | current | This table extends docsIf3CmtsCmRegStatusTable for RPHY. |
| 1.3.6.1.4.1.4491.2.1.30.1.6.1.1 | RowdocsRphyCmtsCmRegStatusEntry | not-accessible | current | The conceptual row of docsRphyCmtsCmRegStatusTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.6.1.1.1 | ColumndocsRphyCmtsCmRegStatusRpdUniqueId | read-only | current | This attribute specifies a globally unique 6-byte identifier of the RPD providing service to the CM specified by the docsIf3CmtsCmRegStatusId index. A complian… |
| 1.3.6.1.4.1.4491.2.1.30.1.6.2 | TabledocsRphyCcapRpdToCmMapStatusTable | not-accessible | current | This table defines a mapping between an RPD Unique Identifier and the corresponding CCAP Core assigned CM Id (CmtsCmRegStatusId). This provides lookup capabili… |
| 1.3.6.1.4.1.4491.2.1.30.1.6.2.1 | RowdocsRphyCcapRpdToCmMapStatusEntry | not-accessible | current | The conceptual row of docsRphyCcapRpdToCmMapStatusTable. |
| 1.3.6.1.4.1.4491.2.1.30.1.6.2.1.1 | ColumndocsRphyCcapRpdToCmMapStatusRpdUsRfPortNum | read-only | current | This attribute identifies the upstream RF port on the RPD, for the RPD attached to the CM specified by the CmId index. A CCAP Core MUST omit reporting RpdUsRfP… |
| 1.3.6.1.4.1.4491.2.1.30.1.6.2.1.2 | ColumndocsRphyCcapRpdToCmMapStatusRpdDsRfPortNum | read-only | current | This attribute identifies the downstream RF port on the RPD, for the RPD attached to the CM specified by the CmId index. A CCAP Core MUST omit reporting RpdDsR… |
| 1.3.6.1.4.1.4491.2.1.30.1.6.2.1.3 | ColumndocsRphyCcapRpdToCmMapStatusNodeRfPortId | read-only | current | This attribute provides a Node RF Port identifier for an RPN. |
| 1.3.6.1.4.1.4491.2.1.30.1.6.2.1.4 | ColumndocsRphyCcapRpdToCmMapStatusRpdUsRfPortList | read-only | current | This attribute is a list of either Full Spectrum or Partial Spectrum UsRfPort indexes with channels in the CM's TCS. |
| 1.3.6.1.4.1.4491.2.1.30.1.6.2.1.5 | ColumndocsRphyCcapRpdToCmMapStatusRpdDsRfPortList | read-only | current | This attribute is a list of either Full Spectrum or Partial Spectrum DsRfPort indexes with channels in the CM's RCS. |
| 1.3.6.1.4.1.4491.2.1.30.2 | NodedocsRphyConformance | |||
| 1.3.6.1.4.1.4491.2.1.30.2.1 | NodedocsRphyCompliances | |||
| 1.3.6.1.4.1.4491.2.1.30.2.1.1 | CompliancedocsRphyCompliance | current | The compliance statement for RPD management features. | |
| 1.3.6.1.4.1.4491.2.1.30.2.1.2 | CompliancedocsRphyDeprecatedCompliance | deprecated | The compliance statement for deprecated RPHY objects. | |
| 1.3.6.1.4.1.4491.2.1.30.2.2 | NodedocsRphyGroups | |||
| 1.3.6.1.4.1.4491.2.1.30.2.2.1 | GroupdocsRphyRpdGroup | current | Group of objects implemented in CCAP Cores which represent RPD managed objects derived via the GCP protocol. | |
| 1.3.6.1.4.1.4491.2.1.30.2.2.2 | GroupdocsRphyCcapCoreGroup | current | Group of objects implemented in CCAP Cores. | |
| 1.3.6.1.4.1.4491.2.1.30.2.2.4 | GroupdocsRphyCmtsCmStatGroup | current | Group of objects implemented to support CMTS Status in CCAP Core. | |
| 1.3.6.1.4.1.4491.2.1.30.2.2.5 | GroupdocsRphyRpdDeprecatedGroup | deprecated | Deprecated RPHY RPD objects group |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| EvPriorityType | INTEGER { emergency(1), alert(2), critical(3), error(4), warning(5), notice(6), information(7), debug(8) } | current | This data type defines an event priority level. These are ordered from most (emergency) to least (debug) critical. Each event has a particular priority level associated with it (as defined by the vendor). |
| OperStatusType | INTEGER { other(0), up(1), down(2), testing(3), dormant(4), notPresent(5), lowerLayerDown(6) } | current | This data type represents the status of the pseudowire from the point of view of the specific reporting entity. Values are as follows: 'other' indicates a vendor-specific operational status. 'up' indicates that the pseu… |
| RfmStatusType | INTEGER { other(1), gcpCfg(2), localCfgNvRam(3), localCfgDefault(4), unknown(5) } | current | This data type defines the Rfm Status Type |
| RphyChannelType | INTEGER { other(0), dsScQam(1), dsOfdm(2), ndf(3), scte551Fwd(4), usAtdma(5), usOfdma(6), reserved(7), ndr(8), scte551Ret(9), dsScte55d2(10), usScte55d2(11) } | current | This data type indicates the type of RPHY channel. |
| SyncEQLType | INTEGER { other(1), prc(2), ssuA(3), ssuB(4), eec1(5), dnu(6), prs(7), stu(9), st2(10), tnc(11), st3e(12), eec2(13), dus(14) } | current | This data type defines the SyncE EQL Type. |