DOT3-MAU-MIB
132 objects
Management information for 802.3 MAUs. The following reference is used throughout this MIB module: [IEEE 802.3 Std] refers to: IEEE Std 802.3, 2002 Edition: 'IEEE Standard for Information technology - Telecommunications and information exchange between systems - Local and metropolitan area networks - Specific requirements - Part 3: Carrier sense multiple access with collision detection (CSMA/CD) access method and physical layer specifications', as amended by IEEE Std 802.3ae-2002: 'Amendment: Media Access Control (MAC) Parameters, Physical Layer, and Management Parameters for 10 Gb/s Operation', August, 2002. Of particular interest is Clause 30, '10Mb/s, 100Mb/s, 1000Mb/s and 10 Gb/s Management'. Copyright (C) The Internet Society (2003). This version of this MIB module is part of RFC 3636; see the RFC itself for full legal notices.
Imported Objects
| IF-MIB | InterfaceIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Counter64 Integer32 mib-2 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | AutonomousType TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 0.0 | ScalarifMauType | read-only | current | |
| 0.0 | ScalarrpMauType | read-only | current | |
| 0.0 | NodeunknownMauType | |||
| 1.3.6.1.2.1.26 | NodesnmpDot3MauMgt | |||
| 1.3.6.1.2.1.26.0 | NodesnmpDot3MauTraps | |||
| 1.3.6.1.2.1.26.0.1 | NotificationrpMauJabberTrap | current | This trap is sent whenever a managed repeater MAU enters the jabber state. The agent MUST throttle the generation of consecutive rpMauJabberTraps so that there… | |
| 1.3.6.1.2.1.26.0.2 | NotificationifMauJabberTrap | current | This trap is sent whenever a managed interface MAU enters the jabber state. The agent MUST throttle the generation of consecutive ifMauJabberTraps so that ther… | |
| 1.3.6.1.2.1.26.1 | Nodedot3RpMauBasicGroup | |||
| 1.3.6.1.2.1.26.1.1 | TablerpMauTable | not-accessible | current | Table of descriptive and status information about the MAU(s) attached to the ports of a repeater. |
| 1.3.6.1.2.1.26.1.1.1 | RowrpMauEntry | not-accessible | current | An entry in the table, containing information about a single MAU. |
| 1.3.6.1.2.1.26.1.1.1.1 | ColumnrpMauGroupIndex | read-only | current | This variable uniquely identifies the group containing the port to which the MAU described by this entry is connected. Note: In practice, a group will generall… |
| 1.3.6.1.2.1.26.1.1.1.2 | ColumnrpMauPortIndex | read-only | current | This variable uniquely identifies the repeater port within group rpMauGroupIndex to which the MAU described by this entry is connected. |
| 1.3.6.1.2.1.26.1.1.1.3 | ColumnrpMauIndex | read-only | current | This variable uniquely identifies the MAU described by this entry from among other MAUs connected to the same port (rpMauPortIndex). |
| 1.3.6.1.2.1.26.1.1.1.5 | ColumnrpMauStatus | read-write | current | The current state of the MAU. This object MAY be implemented as a read-only object by those agents and MAUs that do not implement software control of the MAU s… |
| 1.3.6.1.2.1.26.1.1.1.6 | ColumnrpMauMediaAvailable | read-only | current | If the MAU is a link or fiber type (FOIRL, 10BASE-T, 10BASE-F) then this is equivalent to the link test fail state/low light function. For an AUI or a coax (in… |
| 1.3.6.1.2.1.26.1.1.1.7 | ColumnrpMauMediaAvailableStateExits | read-only | current | A count of the number of times that rpMauMediaAvailable for this MAU instance leaves the state available(3). Discontinuities in the value of this counter can o… |
| 1.3.6.1.2.1.26.1.1.1.8 | ColumnrpMauJabberState | read-only | current | The value other(1) is returned if the jabber state is not 2, 3, or 4. The agent MUST always return other(1) for MAU type dot3MauTypeAUI. The value unknown(2) i… |
| 1.3.6.1.2.1.26.1.1.1.9 | ColumnrpMauJabberingStateEnters | read-only | current | A count of the number of times that mauJabberState for this MAU instance enters the state jabbering(4). For MAUs of type dot3MauTypeAUI, dot3MauType100BaseT4, … |
| 1.3.6.1.2.1.26.1.1.1.10 | ColumnrpMauFalseCarriers | read-only | current | A count of the number of false carrier events during IDLE in 100BASE-X links. This counter does not increment at the symbol rate. It can increment after a vali… |
| 1.3.6.1.2.1.26.1.2 | TablerpJackTable | not-accessible | current | Information about the external jacks attached to MAUs attached to the ports of a repeater. |
| 1.3.6.1.2.1.26.1.2.1 | RowrpJackEntry | not-accessible | current | An entry in the table, containing information about a particular jack. |
| 1.3.6.1.2.1.26.1.2.1.1 | ColumnrpJackIndex | not-accessible | current | This variable uniquely identifies the jack described by this entry from among other jacks attached to the same MAU (rpMauIndex). |
| 1.3.6.1.2.1.26.1.2.1.2 | ColumnrpJackType | read-only | current | The jack connector type, as it appears on the outside of the system. |
| 1.3.6.1.2.1.26.2 | Nodedot3IfMauBasicGroup | |||
| 1.3.6.1.2.1.26.2.1 | TableifMauTable | not-accessible | current | Table of descriptive and status information about MAU(s) attached to an interface. |
| 1.3.6.1.2.1.26.2.1.1 | RowifMauEntry | not-accessible | current | An entry in the table, containing information about a single MAU. |
| 1.3.6.1.2.1.26.2.1.1.1 | ColumnifMauIfIndex | read-only | current | This variable uniquely identifies the interface to which the MAU described by this entry is connected. |
| 1.3.6.1.2.1.26.2.1.1.2 | ColumnifMauIndex | read-only | current | This variable uniquely identifies the MAU described by this entry from among other MAUs connected to the same interface (ifMauIfIndex). |
| 1.3.6.1.2.1.26.2.1.1.4 | ColumnifMauStatus | read-write | current | The current state of the MAU. This object MAY be implemented as a read-only object by those agents and MAUs that do not implement software control of the MAU s… |
| 1.3.6.1.2.1.26.2.1.1.5 | ColumnifMauMediaAvailable | read-only | current | If the MAU is a link or fiber type (FOIRL, 10BASE-T, 10BASE-F) then this is equivalent to the link test fail state/low light function. For an AUI or a coax (in… |
| 1.3.6.1.2.1.26.2.1.1.6 | ColumnifMauMediaAvailableStateExits | read-only | current | A count of the number of times that ifMauMediaAvailable for this MAU instance leaves the state available(3). Discontinuities in the value of this counter can o… |
| 1.3.6.1.2.1.26.2.1.1.7 | ColumnifMauJabberState | read-only | current | The value other(1) is returned if the jabber state is not 2, 3, or 4. The agent MUST always return other(1) for MAU type dot3MauTypeAUI. The value unknown(2) i… |
| 1.3.6.1.2.1.26.2.1.1.8 | ColumnifMauJabberingStateEnters | read-only | current | A count of the number of times that mauJabberState for this MAU instance enters the state jabbering(4). This counter will always indicate zero for MAUs of type… |
| 1.3.6.1.2.1.26.2.1.1.9 | ColumnifMauFalseCarriers | read-only | current | A count of the number of false carrier events during IDLE in 100BASE-X and 1000BASE-X links. For all other MAU types, this counter will always indicate zero. T… |
| 1.3.6.1.2.1.26.2.1.1.10 | ColumnifMauTypeList | read-only | deprecated | ********* THIS OBJECT IS DEPRECATED ********** This object has been deprecated in favour of ifMauTypeListBits. A value that uniquely identifies the set of poss… |
| 1.3.6.1.2.1.26.2.1.1.11 | ColumnifMauDefaultType | read-write | current | This object identifies the default administrative baseband MAU type, to be used in conjunction with the operational MAU type denoted by ifMauType. The set of p… |
| 1.3.6.1.2.1.26.2.1.1.12 | ColumnifMauAutoNegSupported | read-only | current | This object indicates whether or not auto-negotiation is supported on this MAU. |
| 1.3.6.1.2.1.26.2.1.1.13 | ColumnifMauTypeListBits | read-only | current | A value that uniquely identifies the set of possible IEEE 802.3 types that the MAU could be. If auto-negotiation is present on this MAU, this object will map t… |
| 1.3.6.1.2.1.26.2.1.1.14 | ColumnifMauHCFalseCarriers | read-only | current | A count of the number of false carrier events during IDLE in 100BASE-X and 1000BASE-X links. For all other MAU types, this counter will always indicate zero. T… |
| 1.3.6.1.2.1.26.2.2 | TableifJackTable | not-accessible | current | Information about the external jacks attached to MAUs attached to an interface. |
| 1.3.6.1.2.1.26.2.2.1 | RowifJackEntry | not-accessible | current | An entry in the table, containing information about a particular jack. |
| 1.3.6.1.2.1.26.2.2.1.1 | ColumnifJackIndex | not-accessible | current | This variable uniquely identifies the jack described by this entry from among other jacks attached to the same MAU. |
| 1.3.6.1.2.1.26.2.2.1.2 | ColumnifJackType | read-only | current | The jack connector type, as it appears on the outside of the system. |
| 1.3.6.1.2.1.26.3 | Nodedot3BroadMauBasicGroup | |||
| 1.3.6.1.2.1.26.3.1 | TablebroadMauBasicTable | not-accessible | deprecated | ********* THIS OBJECT IS DEPRECATED ********** This entire table has been deprecated. There have been no reported implementations of this table, and it is unli… |
| 1.3.6.1.2.1.26.3.1.1 | RowbroadMauBasicEntry | not-accessible | deprecated | ********* THIS OBJECT IS DEPRECATED ********** An entry in the table, containing information about a single broadband MAU. |
| 1.3.6.1.2.1.26.3.1.1.1 | ColumnbroadMauIfIndex | read-only | deprecated | ********* THIS OBJECT IS DEPRECATED ********** This variable uniquely identifies the interface to which the MAU described by this entry is connected. |
| 1.3.6.1.2.1.26.3.1.1.2 | ColumnbroadMauIndex | read-only | deprecated | ********* THIS OBJECT IS DEPRECATED ********** This variable uniquely identifies the MAU connected to interface broadMauIfIndex that is described by this entry. |
| 1.3.6.1.2.1.26.3.1.1.3 | ColumnbroadMauXmtRcvSplitType | read-only | deprecated | ********* THIS OBJECT IS DEPRECATED ********** This object indicates the type of frequency multiplexing/cabling system used to separate the transmit and receiv… |
| 1.3.6.1.2.1.26.3.1.1.4 | ColumnbroadMauXmtCarrierFreq | read-only | deprecated | ********* THIS OBJECT IS DEPRECATED ********** This variable indicates the transmit carrier frequency of the 10BROAD36 MAU in MHz/4; that is, in units of 250 k… |
| 1.3.6.1.2.1.26.3.1.1.5 | ColumnbroadMauTranslationFreq | read-only | deprecated | ********* THIS OBJECT IS DEPRECATED ********** This variable indicates the translation offset frequency of the 10BROAD36 MAU in MHz/4; that is, in units of 250… |
| 1.3.6.1.2.1.26.4 | Nodedot3MauType | |||
| 1.3.6.1.2.1.26.4.1 | Identitydot3MauTypeAUI | current | no internal MAU, view from AUI | |
| 1.3.6.1.2.1.26.4.2 | Identitydot3MauType10Base5 | current | thick coax MAU | |
| 1.3.6.1.2.1.26.4.3 | Identitydot3MauTypeFoirl | current | FOIRL MAU | |
| 1.3.6.1.2.1.26.4.4 | Identitydot3MauType10Base2 | current | thin coax MAU | |
| 1.3.6.1.2.1.26.4.5 | Identitydot3MauType10BaseT | current | UTP MAU. Note that it is strongly recommended that agents return either dot3MauType10BaseTHD or dot3MauType10BaseTFD if the duplex mode is known. However, mana… | |
| 1.3.6.1.2.1.26.4.6 | Identitydot3MauType10BaseFP | current | passive fiber MAU | |
| 1.3.6.1.2.1.26.4.7 | Identitydot3MauType10BaseFB | current | sync fiber MAU | |
| 1.3.6.1.2.1.26.4.8 | Identitydot3MauType10BaseFL | current | async fiber MAU. Note that it is strongly recommended that agents return either dot3MauType10BaseFLHD or dot3MauType10BaseFLFD if the duplex mode is known. How… | |
| 1.3.6.1.2.1.26.4.9 | Identitydot3MauType10Broad36 | current | broadband DTE MAU. Note that 10BROAD36 MAUs can be attached to interfaces but not to repeaters. | |
| 1.3.6.1.2.1.26.4.10 | Identitydot3MauType10BaseTHD | current | UTP MAU, half duplex mode | |
| 1.3.6.1.2.1.26.4.11 | Identitydot3MauType10BaseTFD | current | UTP MAU, full duplex mode | |
| 1.3.6.1.2.1.26.4.12 | Identitydot3MauType10BaseFLHD | current | async fiber MAU, half duplex mode | |
| 1.3.6.1.2.1.26.4.13 | Identitydot3MauType10BaseFLFD | current | async fiber MAU, full duplex mode | |
| 1.3.6.1.2.1.26.4.14 | Identitydot3MauType100BaseT4 | current | 4 pair category 3 UTP | |
| 1.3.6.1.2.1.26.4.15 | Identitydot3MauType100BaseTXHD | current | 2 pair category 5 UTP, half duplex mode | |
| 1.3.6.1.2.1.26.4.16 | Identitydot3MauType100BaseTXFD | current | 2 pair category 5 UTP, full duplex mode | |
| 1.3.6.1.2.1.26.4.17 | Identitydot3MauType100BaseFXHD | current | X fiber over PMT, half duplex mode | |
| 1.3.6.1.2.1.26.4.18 | Identitydot3MauType100BaseFXFD | current | X fiber over PMT, full duplex mode | |
| 1.3.6.1.2.1.26.4.19 | Identitydot3MauType100BaseT2HD | current | 2 pair category 3 UTP, half duplex mode | |
| 1.3.6.1.2.1.26.4.20 | Identitydot3MauType100BaseT2FD | current | 2 pair category 3 UTP, full duplex mode | |
| 1.3.6.1.2.1.26.4.21 | Identitydot3MauType1000BaseXHD | current | PCS/PMA, unknown PMD, half duplex mode | |
| 1.3.6.1.2.1.26.4.22 | Identitydot3MauType1000BaseXFD | current | PCS/PMA, unknown PMD, full duplex mode | |
| 1.3.6.1.2.1.26.4.23 | Identitydot3MauType1000BaseLXHD | current | Fiber over long-wavelength laser, half duplex mode | |
| 1.3.6.1.2.1.26.4.24 | Identitydot3MauType1000BaseLXFD | current | Fiber over long-wavelength laser, full duplex mode | |
| 1.3.6.1.2.1.26.4.25 | Identitydot3MauType1000BaseSXHD | current | Fiber over short-wavelength laser, half duplex mode | |
| 1.3.6.1.2.1.26.4.26 | Identitydot3MauType1000BaseSXFD | current | Fiber over short-wavelength laser, full duplex mode | |
| 1.3.6.1.2.1.26.4.27 | Identitydot3MauType1000BaseCXHD | current | Copper over 150-Ohm balanced cable, half duplex mode | |
| 1.3.6.1.2.1.26.4.28 | Identitydot3MauType1000BaseCXFD | current | Copper over 150-Ohm balanced cable, full duplex mode | |
| 1.3.6.1.2.1.26.4.29 | Identitydot3MauType1000BaseTHD | current | Four-pair Category 5 UTP, half duplex mode | |
| 1.3.6.1.2.1.26.4.30 | Identitydot3MauType1000BaseTFD | current | Four-pair Category 5 UTP, full duplex mode | |
| 1.3.6.1.2.1.26.4.31 | Identitydot3MauType10GigBaseX | current | X PCS/PMA, unknown PMD. | |
| 1.3.6.1.2.1.26.4.32 | Identitydot3MauType10GigBaseLX4 | current | X fiber over WWDM optics | |
| 1.3.6.1.2.1.26.4.33 | Identitydot3MauType10GigBaseR | current | R PCS/PMA, unknown PMD. | |
| 1.3.6.1.2.1.26.4.34 | Identitydot3MauType10GigBaseER | current | R fiber over 1550 nm optics | |
| 1.3.6.1.2.1.26.4.35 | Identitydot3MauType10GigBaseLR | current | R fiber over 1310 nm optics | |
| 1.3.6.1.2.1.26.4.36 | Identitydot3MauType10GigBaseSR | current | R fiber over 850 nm optics | |
| 1.3.6.1.2.1.26.4.37 | Identitydot3MauType10GigBaseW | current | W PCS/PMA, unknown PMD. | |
| 1.3.6.1.2.1.26.4.38 | Identitydot3MauType10GigBaseEW | current | W fiber over 1550 nm optics | |
| 1.3.6.1.2.1.26.4.39 | Identitydot3MauType10GigBaseLW | current | W fiber over 1310 nm optics | |
| 1.3.6.1.2.1.26.4.40 | Identitydot3MauType10GigBaseSW | current | W fiber over 850 nm optics | |
| 1.3.6.1.2.1.26.5 | Nodedot3IfMauAutoNegGroup | |||
| 1.3.6.1.2.1.26.5.1 | TableifMauAutoNegTable | not-accessible | current | Configuration and status objects for the auto-negotiation function of MAUs attached to interfaces. The ifMauAutoNegTable applies to systems in which auto-negot… |
| 1.3.6.1.2.1.26.5.1.1 | RowifMauAutoNegEntry | not-accessible | current | An entry in the table, containing configuration and status information for the auto-negotiation function of a particular MAU. |
| 1.3.6.1.2.1.26.5.1.1.1 | ColumnifMauAutoNegAdminStatus | read-write | current | Setting this object to enabled(1) will cause the interface which has the auto-negotiation signaling ability to be enabled. If the value of this object is disab… |
| 1.3.6.1.2.1.26.5.1.1.2 | ColumnifMauAutoNegRemoteSignaling | read-only | current | A value indicating whether the remote end of the link is using auto-negotiation signaling. It takes the value detected(1) if and only if, during the previous l… |
| 1.3.6.1.2.1.26.5.1.1.4 | ColumnifMauAutoNegConfig | read-only | current | A value indicating the current status of the auto-negotiation process. The enumeration parallelDetectFail(5) maps to a failure in parallel detection as defined… |
| 1.3.6.1.2.1.26.5.1.1.5 | ColumnifMauAutoNegCapability | read-only | deprecated | ********* THIS OBJECT IS DEPRECATED ********** This object has been deprecated in favour of ifMauAutoNegCapabilityBits. A value that uniquely identifies the se… |
| 1.3.6.1.2.1.26.5.1.1.6 | ColumnifMauAutoNegCapAdvertised | read-write | deprecated | ********* THIS OBJECT IS DEPRECATED ********** This object has been deprecated in favour of ifMauAutoNegCapAdvertisedBits. A value that uniquely identifies the… |
| 1.3.6.1.2.1.26.5.1.1.7 | ColumnifMauAutoNegCapReceived | read-only | deprecated | ********* THIS OBJECT IS DEPRECATED ********** This object has been deprecated in favour of ifMauAutoNegCapReceivedBits. A value that uniquely identifies the s… |
| 1.3.6.1.2.1.26.5.1.1.8 | ColumnifMauAutoNegRestart | read-write | current | If the value of this object is set to restart(1) then this will force auto-negotiation to begin link renegotiation. If auto-negotiation signaling is disabled, … |
| 1.3.6.1.2.1.26.5.1.1.9 | ColumnifMauAutoNegCapabilityBits | read-only | current | A value that uniquely identifies the set of capabilities of the local auto-negotiation entity. Note that interfaces that support this MIB may have capabilities… |
| 1.3.6.1.2.1.26.5.1.1.10 | ColumnifMauAutoNegCapAdvertisedBits | read-write | current | A value that uniquely identifies the set of capabilities advertised by the local auto-negotiation entity. Capabilities in this object that are not available in… |
| 1.3.6.1.2.1.26.5.1.1.11 | ColumnifMauAutoNegCapReceivedBits | read-only | current | A value that uniquely identifies the set of capabilities received from the remote auto-negotiation entity. Note that interfaces that support this MIB may be at… |
| 1.3.6.1.2.1.26.5.1.1.12 | ColumnifMauAutoNegRemoteFaultAdvertised | read-write | current | A value that identifies any local fault indications that this MAU has detected and will advertise at the next auto-negotiation interaction for 1000Mbps MAUs. |
| 1.3.6.1.2.1.26.5.1.1.13 | ColumnifMauAutoNegRemoteFaultReceived | read-only | current | A value that identifies any fault indications received from the far end of a link by the local auto-negotiation entity for 1000Mbps MAUs. |
| 1.3.6.1.2.1.26.6 | IdentitymauMod | Management information for 802.3 MAUs. The following reference is used throughout this MIB module: [IEEE 802.3 Std] refers to: IEEE Std 802.3, 2002 Edition: 'I… | ||
| 1.3.6.1.2.1.26.6.1 | NodemauModConf | |||
| 1.3.6.1.2.1.26.6.1.1 | NodemauModCompls | |||
| 1.3.6.1.2.1.26.6.1.1.1 | CompliancemauModRpCompl | deprecated | ******** THIS COMPLIANCE IS DEPRECATED ******** Compliance for MAUs attached to repeater ports. This compliance is deprecated and replaced by mauModRpCompl2, w… | |
| 1.3.6.1.2.1.26.6.1.1.2 | CompliancemauModIfCompl | deprecated | ******** THIS COMPLIANCE IS DEPRECATED ******** Compliance for MAUs attached to interfaces. This compliance is deprecated and replaced by mauModIfCompl2. | |
| 1.3.6.1.2.1.26.6.1.1.3 | CompliancemauModIfCompl2 | read-only | deprecated | ******** THIS COMPLIANCE IS DEPRECATED ******** Compliance for MAUs attached to interfaces. This compliance is deprecated and replaced by mauModIfCompl3. |
| 1.3.6.1.2.1.26.6.1.1.4 | CompliancemauModRpCompl2 | read-only | current | Compliance for MAUs attached to repeater ports. Note that compliance with this compliance statement requires compliance with the snmpRptrModCompl MODULE-COMPLI… |
| 1.3.6.1.2.1.26.6.1.1.5 | CompliancemauModIfCompl3 | read-only | current | Compliance for MAUs attached to interfaces. Note that compliance with this compliance statement requires compliance with the ifCompliance3 MODULE-COMPLIANCE st… |
| 1.3.6.1.2.1.26.6.1.2 | NodemauModObjGrps | |||
| 1.3.6.1.2.1.26.6.1.2.1 | GroupmauRpGrpBasic | current | Basic conformance group for MAUs attached to repeater ports. This group is also the conformance specification for RFC 1515 implementations. | |
| 1.3.6.1.2.1.26.6.1.2.2 | GroupmauRpGrp100Mbs | current | Conformance group for MAUs attached to repeater ports with 100 Mb/s or greater capability. | |
| 1.3.6.1.2.1.26.6.1.2.3 | GroupmauRpGrpJack | current | Conformance group for MAUs attached to repeater ports with managed jacks. | |
| 1.3.6.1.2.1.26.6.1.2.4 | GroupmauIfGrpBasic | current | Basic conformance group for MAUs attached to interfaces. This group also provides a conformance specification for RFC 1515 implementations. | |
| 1.3.6.1.2.1.26.6.1.2.5 | GroupmauIfGrp100Mbs | deprecated | ********* THIS GROUP IS DEPRECATED ********** Conformance group for MAUs attached to interfaces with 100 Mb/s capability. This object group has been deprecated… | |
| 1.3.6.1.2.1.26.6.1.2.6 | GroupmauIfGrpJack | current | Conformance group for MAUs attached to interfaces with managed jacks. | |
| 1.3.6.1.2.1.26.6.1.2.7 | GroupmauIfGrpAutoNeg | deprecated | ********* THIS GROUP IS DEPRECATED ********** Conformance group for MAUs attached to interfaces with managed auto-negotiation. This object group has been depre… | |
| 1.3.6.1.2.1.26.6.1.2.8 | GroupmauBroadBasic | deprecated | ********* THIS GROUP IS DEPRECATED ********** Conformance group for broadband MAUs attached to interfaces. This object group is deprecated. There have been no … | |
| 1.3.6.1.2.1.26.6.1.2.9 | GroupmauIfGrpHighCapacity | current | Conformance group for MAUs attached to interfaces with 100 Mb/s or greater capability. | |
| 1.3.6.1.2.1.26.6.1.2.10 | GroupmauIfGrpAutoNeg2 | current | Conformance group for MAUs attached to interfaces with managed auto-negotiation. | |
| 1.3.6.1.2.1.26.6.1.2.11 | GroupmauIfGrpAutoNeg1000Mbps | current | Conformance group for 1000Mbps MAUs attached to interfaces with managed auto-negotiation. | |
| 1.3.6.1.2.1.26.6.1.2.12 | GroupmauIfGrpHCStats | current | Conformance for high capacity statistics for MAUs attached to interfaces | |
| 1.3.6.1.2.1.26.6.1.3 | NodemauModNotGrps | |||
| 1.3.6.1.2.1.26.6.1.3.1 | GrouprpMauNotifications | current | Notifications for repeater MAUs. | |
| 1.3.6.1.2.1.26.6.1.3.2 | GroupifMauNotifications | current | Notifications for interface MAUs. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| JackType | INTEGER { other(1), rj45(2), rj45S(3), db9(4), bnc(5), fAUI(6), mAUI(7), fiberSC(8), fiberMIC(9), fiberST(10), telco(11), mtrj(12), hssdc(13), fiberLC(14) } | current | Common enumeration values for repeater and interface MAU jack types. |