EDB-snmp
113 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | Counter Gauge internet IpAddress mgmt NetworkAddress TimeTicks |
| RFC1213-MIB | PhysAddress |
| SNMPv2-TC | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4 | Nodeprivate | |||
| 1.3.6.1.4.1 | Nodeenterprises | |||
| 1.3.6.1.4.1.22 | Nodefibronics | |||
| 1.3.6.1.4.1.22.3 | Nodetrap | |||
| 1.3.6.1.4.1.22.3.1 | Nodetraprun | |||
| 1.3.6.1.4.1.22.3.1.1 | TablerTrapAddrTbl | not-accessible | mandatory | Table of managers to which traps must be sent. Up to 10 entries in table |
| 1.3.6.1.4.1.22.3.1.1.1 | RowrTrapAddrEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.22.3.1.1.1.1 | ColumnrTrapAddrAddr | read-write | mandatory | IP address of entity requesting event notification |
| 1.3.6.1.4.1.22.3.1.1.1.2 | ColumnrTrapAddrComm | read-write | mandatory | Community name the receiving entity will expect. When reading the instance of this object the value has no meaning. |
| 1.3.6.1.4.1.22.3.1.1.1.3 | ColumnrTrapAddrVer | read-write | mandatory | Version number supported by destination node |
| 1.3.6.1.4.1.22.3.1.1.1.4 | ColumnrTrapAddrType | read-write | mandatory | Type of event that should be reported to this address, bit 0 - authentication trap bit 1 - other SNMP traps bit 2 - Error Traps bit 3 - Diagnostic Traps bit 4 … |
| 1.3.6.1.4.1.22.3.1.1.1.5 | ColumnrTrapAddrState | read-write | mandatory | Determines status of this entry |
| 1.3.6.1.4.1.22.3.1.1.1.6 | ColumnrTrapAddrFlag | read-write | mandatory | If the entry is fixed, it can not be deleted because of aging |
| 1.3.6.1.4.1.22.3.1.1.1.7 | ColumnrTrapAddrAge | read-only | mandatory | Aging time of the entry (in sec) |
| 1.3.6.1.4.1.22.3.1.2 | ScalarrTrapLearning | read-only | mandatory | Learn the addresses of the managers automatically. |
| 1.3.6.1.4.1.22.3.1.3 | ScalarrTrapAging | read-only | mandatory | Time in sec. until we erase a trap entry |
| 1.3.6.1.4.1.22.3.2 | Nodetraperm | |||
| 1.3.6.1.4.1.22.3.2.1 | TablepTrapAddrTbl | not-accessible | mandatory | Table of managers to which traps must be sent. Up to 10 entries in table |
| 1.3.6.1.4.1.22.3.2.1.1 | RowpTrapAddrEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.22.3.2.1.1.1 | ColumnpTrapAddrAddr | read-write | mandatory | IP address of entity requesting event notification |
| 1.3.6.1.4.1.22.3.2.1.1.2 | ColumnpTrapAddrComm | read-write | mandatory | Community name the receiving entity will expect. When reading the instance of this object the value has no meaning. |
| 1.3.6.1.4.1.22.3.2.1.1.3 | ColumnpTrapAddrVer | read-write | mandatory | Version number supported by destination node |
| 1.3.6.1.4.1.22.3.2.1.1.4 | ColumnpTrapAddrType | read-write | mandatory | Type of event that should be reported to this address, bit 0 - authentication trap bit 1 - other SNMP traps bit 2 - Error Traps bit 3 - Diagnostic Traps bit 4 … |
| 1.3.6.1.4.1.22.3.2.1.1.5 | ColumnpTrapAddrState | read-write | mandatory | Determines status of this entry |
| 1.3.6.1.4.1.22.3.2.2 | ScalarpTrapLearning | read-write | mandatory | Learn the addresses of the managers automatically. |
| 1.3.6.1.4.1.22.3.2.3 | ScalarpTrapAging | read-write | mandatory | Time in sec. until we erase a trap entry |
| 1.3.6.1.4.1.22.3.3 | Nodetrapvar | |||
| 1.3.6.1.4.1.22.51 | Nodefm800 | |||
| 1.3.6.1.4.1.22.51.1 | NodefmPowerSupplyFail | This trap message is generated as soon as one of the power supply has failed | ||
| 1.3.6.1.4.1.22.51.1 | Nodefmsystem | |||
| 1.3.6.1.4.1.22.51.1.1 | Nodefmsystemrun | |||
| 1.3.6.1.4.1.22.51.1.1.1 | ScalarfmSystemPSAdmin | read-write | mandatory | Changes power supply to primary or secondary. When reading the instance of this object the value has no meaning. |
| 1.3.6.1.4.1.22.51.1.1.2 | ScalarfmSystemPSOper | read-only | mandatory | Which power supply active |
| 1.3.6.1.4.1.22.51.1.1.3 | ScalarfmSystemPSCfg | read-write | mandatory | Configuration of power supply |
| 1.3.6.1.4.1.22.51.1.1.4 | ScalarfmSystemReset | read-write | mandatory | Resetting the CARD. When reading the instance of this object the value has no meaning. cold reset is performed with selftest , while warm start is performed wi… |
| 1.3.6.1.4.1.22.51.1.1.5 | ScalarfmSystemSelfTestLevel | read-write | mandatory | Type of self test to be executed upon cold-reset |
| 1.3.6.1.4.1.22.51.1.1.6 | ScalarfmSystemVersion | read-only | mandatory | Version of the station. The version includes station type, hardware version and software version. The string can include CR and LF |
| 1.3.6.1.4.1.22.51.1.1.7 | ScalarfmSystemIpAddr | read-only | mandatory | IP address of the agent |
| 1.3.6.1.4.1.22.51.1.1.8 | ScalarfmSystemIPNetMask | read-only | mandatory | IP Network Mask |
| 1.3.6.1.4.1.22.51.1.1.9 | ScalarfmSystemIPDefGway | read-only | mandatory | Default Gateway Address |
| 1.3.6.1.4.1.22.51.1.1.10 | ScalarfmSystemFileServer | read-write | mandatory | IP address to which a TFTP for boot is sent. |
| 1.3.6.1.4.1.22.51.1.1.11 | ScalarfmSystemBootFile | read-only | mandatory | Path and file name that is sent as a TFTP request |
| 1.3.6.1.4.1.22.51.1.1.12 | ScalarfmSystemBootMode | read-only | deprecated | Method for booting |
| 1.3.6.1.4.1.22.51.1.1.13 | ScalarfmSystemDownLoad | read-write | mandatory | Downloading the EDB. When reading the instance of this object the value has no meaning. |
| 1.3.6.1.4.1.22.51.1.1.14 | ScalarfmSystemSlipIpAddr | read-only | mandatory | SLIP IP address. This is object is available only when slip interface exist |
| 1.3.6.1.4.1.22.51.1.1.15 | ScalarfmSystemSlipIPNetMask | read-only | mandatory | SLIP IP Network Mask This is object is available only when slip interface exist |
| 1.3.6.1.4.1.22.51.1.1.16 | ScalarfmSystemSlipBaudRate | read-only | mandatory | SLIP Baud rate This is object is available only when slip interface exist |
| 1.3.6.1.4.1.22.51.1.1.17 | ScalarfmSystemSlipParity | read-only | mandatory | SLIP Parity This is object is available only when slip interface exist |
| 1.3.6.1.4.1.22.51.1.1.18 | ScalarfmSystemSlipStopBits | read-only | mandatory | SLIP Stop Bits This is object is available only when slip interface exist |
| 1.3.6.1.4.1.22.51.1.2 | Nodefmsystemperm | |||
| 1.3.6.1.4.1.22.51.1.2.7 | ScalarpfmSystemIpAddr | read-write | mandatory | IP address of the agent |
| 1.3.6.1.4.1.22.51.1.2.8 | ScalarpfmSystemIPNetMask | read-write | mandatory | IP Network Mask |
| 1.3.6.1.4.1.22.51.1.2.9 | ScalarpfmSystemIPDefGway | read-write | mandatory | Default Gateway Address |
| 1.3.6.1.4.1.22.51.1.2.10 | ScalarpfmSystemFileServer | read-write | mandatory | IP address to which a TFTP for boot is sent. |
| 1.3.6.1.4.1.22.51.1.2.11 | ScalarpfmSystemBootFile | read-write | mandatory | Path and file name that is sent as a TFTP request |
| 1.3.6.1.4.1.22.51.1.2.12 | ScalarpfmSystemBootMode | read-write | mandatory | Method for booting |
| 1.3.6.1.4.1.22.51.1.2.13 | ScalarpfmSystemReadCommunity | read-write | mandatory | Community string for reading When reading the instance of this object the value has no meaning. |
| 1.3.6.1.4.1.22.51.1.2.14 | ScalarpfmSystemWriteCommunity | read-write | mandatory | Community string for writing When reading the instance of this object the value has no meaning. |
| 1.3.6.1.4.1.22.51.1.2.15 | ScalarpfmSystemSlipIpAddr | read-write | mandatory | SLIP IP address This is object is available only when slip interface exist |
| 1.3.6.1.4.1.22.51.1.2.16 | ScalarpfmSystemSlipIPNetMask | read-write | mandatory | SLIP IP Network Mask This is object is available only when slip interface exist |
| 1.3.6.1.4.1.22.51.1.2.17 | ScalarpfmSystemSlipBaudRate | read-write | mandatory | SLIP Baud rate This is object is available only when slip interface exist |
| 1.3.6.1.4.1.22.51.1.2.18 | ScalarpfmSystemSlipParity | read-write | mandatory | SLIP Parity This is object is available only when slip interface exist |
| 1.3.6.1.4.1.22.51.1.2.19 | ScalarpfmSystemSlipStopBits | read-write | mandatory | SLIP Stop Bits This is object is available only when slip interface exist |
| 1.3.6.1.4.1.22.51.2 | NodefmPrimaryPowerSupplyOK | This trap is issued when primary power supply return to work | ||
| 1.3.6.1.4.1.22.51.2 | Nodefmslot | |||
| 1.3.6.1.4.1.22.51.2.1 | ScalarfmSlotMasterClear | read-write | mandatory | Upon writing, performs a master clear command on all the slots. When reading the instance of this object the value has no meaning. |
| 1.3.6.1.4.1.22.51.2.2 | TablefmSlotTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.22.51.2.2.1 | RowfmSlotEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.22.51.2.2.1.1 | ColumnfmSlotIndex | read-only | mandatory | Slot Number |
| 1.3.6.1.4.1.22.51.2.2.1.2 | ColumnfmSlotID | read-write | mandatory | ID of the card in the slot |
| 1.3.6.1.4.1.22.51.2.2.1.3 | ColumnfmSlotDescr | read-only | mandatory | Ascii string. Description of the card |
| 1.3.6.1.4.1.22.51.2.2.1.4 | ColumnfmSlotInfo | read-write | mandatory | User general info for the slot. Can be the use of that slot, its location etc... |
| 1.3.6.1.4.1.22.51.2.2.1.5 | ColumnfmSlotStatus | read-only | mandatory | 8 bytes. 60 status bits of the card. For more information about the meaning of the status, read the specific user manual of each card. The channel leds are enc… |
| 1.3.6.1.4.1.22.51.2.2.1.6 | ColumnfmSlotPrevStatus | read-only | mandatory | 8 bytes. Previous 60 status bits of the card. This object id is used mainly for traps (see Card Trap) |
| 1.3.6.1.4.1.22.51.2.2.1.7 | ColumnfmSlotRLBSet | read-write | mandatory | Argument: 1 - 4. Perform a RLB set operation on the channel passed as argument. When reading the instance of this object the value has no meaning. |
| 1.3.6.1.4.1.22.51.2.2.1.8 | ColumnfmSlotRLBClear | read-write | mandatory | Argument: 1 - 4. Perform a RLB clear operation on the channel passed as argument. When reading the instance of this object the value has no meaning. |
| 1.3.6.1.4.1.22.51.2.2.1.9 | ColumnfmSlotExpCode | read-write | mandatory | Perform an expanded command on the slot. For expanded codes, see specific card user manual. When reading the instance of this object the value has no meaning. … |
| 1.3.6.1.4.1.22.51.2.2.1.10 | ColumnfmSlotTrapMask | read-write | mandatory | When the value is 1, no more traps from that slot are sent, until next reset. (temporary mask) |
| 1.3.6.1.4.1.22.51.2.2.1.11 | ColumnpfmSlotTrapMask | read-write | mandatory | When the value is 1, no more traps for that slot will be sent, starting after next reset (permanent mask) |
| 1.3.6.1.4.1.22.51.2.2.1.12 | ColumnfmSlotIpAddr | read-only | mandatory | IP address of a channel card. This is object is available only for channel cards which have their own IP addresses (e.g., LC303/129) |
| 1.3.6.1.4.1.22.51.3 | NodefmSecondPowerSupplyOK | This trap is issued when second power supply return to work | ||
| 1.3.6.1.4.1.22.51.3 | Nodefmlu | |||
| 1.3.6.1.4.1.22.51.3.1 | ScalarfmLUID | read-write | mandatory | Logic unit ID |
| 1.3.6.1.4.1.22.51.3.2 | ScalarfmLUDescr | read-only | mandatory | Ascii string. Description of the logic unit |
| 1.3.6.1.4.1.22.51.3.3 | ScalarfmLUStatus | read-only | mandatory | One byte of LU status |
| 1.3.6.1.4.1.22.51.3.4 | ScalarfmLULinkSelect | read-write | mandatory | Setup LU link. |
| 1.3.6.1.4.1.22.51.3.5 | ScalarfmLULoopBackSet | read-write | mandatory | Upon writing, performs LLB command. When reading the instance of this object the value has no meaning. |
| 1.3.6.1.4.1.22.51.3.6 | ScalarfmLULoopBackClr | read-write | mandatory | Upon writing, clear LLB command. When reading the instance of this object the value has no meaning. |
| 1.3.6.1.4.1.22.51.3.7 | ScalarfmLUTrapMask | read-write | mandatory | When the value is 1, no more traps from the LU are sent, until next reset. (temporary mask) |
| 1.3.6.1.4.1.22.51.3.8 | ScalarpfmLUTrapMask | read-write | mandatory | When the value is 1, no more traps for the LU will be sent, starting after next reset (permanent mask) |
| 1.3.6.1.4.1.22.51.4 | NodefmPowerSupplyChangeConfig | Issued when a change in the configuration of the power supply is done | ||
| 1.3.6.1.4.1.22.51.5 | Nodefmdiag | |||
| 1.3.6.1.4.1.22.51.5.1 | ScalarfmDiagConfig | read-only | mandatory | Version of the station. The version includes station type, hardware version and software version. The string can include CR and LF |
| 1.3.6.1.4.1.22.51.5.2 | ScalarfmDiagTrapInfo | read-only | mandatory | Used for generic traps. The first word is the trap code. The rest of the string is the extra information. Contains CR and LF char. |
| 1.3.6.1.4.1.22.51.5.3 | TablefmDiagFaultTable | not-accessible | optional | Table of fault reports from the agent |
| 1.3.6.1.4.1.22.51.5.3.1 | RowfmDiagFaultEntry | not-accessible | optional | |
| 1.3.6.1.4.1.22.51.5.3.1.1 | ColumnfmDiagFaultIndex | read-only | optional | The fault index in the fault table |
| 1.3.6.1.4.1.22.51.5.3.1.2 | ColumnfmDiagFaultReport | read-only | optional | Get the faults detected by the agent |
| 1.3.6.1.4.1.22.51.5.4 | ScalarfmDiagDebug | read-write | mandatory | This object is for factory use only. Users must not write into this variable or improper operation can occur. |
| 1.3.6.1.4.1.22.51.7 | NodefmLUOutOfSync | Issued when the Logic unit goes out of synchronization | ||
| 1.3.6.1.4.1.22.51.8 | NodefmLUReturnToSync | Issues as soon as the logic unit returns to synchronization | ||
| 1.3.6.1.4.1.22.51.9 | NodefmLUPassToMain | Issues as soon as the logic unit pass to main link | ||
| 1.3.6.1.4.1.22.51.10 | NodefmLUPassToSecond | Issues as soon as the logic unit pass to second link | ||
| 1.3.6.1.4.1.22.51.11 | NodefmLUPrimaryLinkFail | When primary link of the logic unit fails this trap is issued | ||
| 1.3.6.1.4.1.22.51.12 | NodefmLUPrimaryLinkOK | When primary link of the logic unit fails this trap is issued | ||
| 1.3.6.1.4.1.22.51.13 | NodefmLUSecondLinkFail | When second link of the logic unit fails this trap is issued | ||
| 1.3.6.1.4.1.22.51.14 | NodefmLUSecondLinkOK | When second link of the logic unit fails this trap is issued | ||
| 1.3.6.1.4.1.22.51.15 | NodefmLULLBOn | When the logic unit enters LLB mode | ||
| 1.3.6.1.4.1.22.51.16 | NodefmLULLBOff | When the logic unit exits LLB mode | ||
| 1.3.6.1.4.1.22.51.20 | NodefmLUChangeConfig | Issues when a change in the LU configuration is done | ||
| 1.3.6.1.4.1.22.51.25 | NodefmSlotTrap | Generated when a significant status has changed in a slot. By xoring the 2 statuses, the NMS can identify the cause of the trap. | ||
| 1.3.6.1.4.1.22.51.26 | NodefmSlotChangeConfig | Issued when the system detects changes in its slots configuration | ||
| 1.3.6.1.4.1.22.51.30 | NodefmDiagGenericTrap | Generic Trap information |