Es2952-MIB
375 objects
No module-level DESCRIPTION found.
Imported Objects
| SNMPv2-SMI | enterprises Integer32 IpAddress OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.3902 | Nodezte | |||
| 1.3.6.1.4.1.3902.15 | NodeethernetSwitch | |||
| 1.3.6.1.4.1.3902.15.2 | Nodelayer2Switch | |||
| 1.3.6.1.4.1.3902.15.2.11 | Nodeseries2952Switch | |||
| 1.3.6.1.4.1.3902.15.2.11.1 | NodeswitchSystem | |||
| 1.3.6.1.4.1.3902.15.2.11.1.1 | ScalarcpuLoad5s | read-only | current | The Avg. Value of CPU Load for 5 seconds described by percent. |
| 1.3.6.1.4.1.3902.15.2.11.1.2 | ScalarcpuLoad30s | read-only | current | The Avg. Value of CPU Load for 30 seconds described by percent. |
| 1.3.6.1.4.1.3902.15.2.11.1.3 | ScalarcpuLoad2m | read-only | current | The Avg. Value of CPU Load for 2 minutes described by percent. |
| 1.3.6.1.4.1.3902.15.2.11.1.4 | ScalarmaxCpuLoad | read-only | current | The cpu max utility described by percent. |
| 1.3.6.1.4.1.3902.15.2.11.1.5 | ScalarmemUtilityRatio | read-only | current | The utility ratio of system memery described by percent. |
| 1.3.6.1.4.1.3902.15.2.11.1.6 | ScalarswitchType | read-only | current | The switch type. |
| 1.3.6.1.4.1.3902.15.2.11.1.7 | ScalarswitchMac | read-only | current | The mac address of device. |
| 1.3.6.1.4.1.3902.15.2.11.1.8 | Scalarreboot | read-write | current | reboot system or not |
| 1.3.6.1.4.1.3902.15.2.11.1.9 | ScalarsaveConfig | read-write | current | save running-config information or not |
| 1.3.6.1.4.1.3902.15.2.11.1.10 | ScalarsysDateTime | read-write | current | System current date and time. The format is YYYYMMDD-hh:mm:ss,such as 20060424-09:30:20. |
| 1.3.6.1.4.1.3902.15.2.11.2 | Nodeport | |||
| 1.3.6.1.4.1.3902.15.2.11.2.1 | ScalarportNumber | read-only | current | The number of network interfaces (regardless of their current state) present on this system. |
| 1.3.6.1.4.1.3902.15.2.11.2.4 | TableportTable | not-accessible | current | A list of port entries. The number of entries is given by the value of portNumber. |
| 1.3.6.1.4.1.3902.15.2.11.2.4.1 | RowportEntry | not-accessible | current | A port entry containing objects at the subnetwork layer and below for a particular port. |
| 1.3.6.1.4.1.3902.15.2.11.2.4.1.1 | ColumnportId | read-only | current | The port id |
| 1.3.6.1.4.1.3902.15.2.11.2.4.1.2 | ColumnportName | read-write | current | Port name(maxsize:200,number 1~255 are reserved). |
| 1.3.6.1.4.1.3902.15.2.11.2.4.1.3 | ColumnportDescr | read-write | current | Description of a port |
| 1.3.6.1.4.1.3902.15.2.11.2.4.1.4 | ColumnportAdminStatus | read-write | current | The desired state of the port. |
| 1.3.6.1.4.1.3902.15.2.11.2.4.1.5 | ColumnportOperStatus | read-only | current | The current operational state of the port. |
| 1.3.6.1.4.1.3902.15.2.11.2.4.1.6 | ColumnportAdminWorkMode | read-write | current | This item config port working mode. |
| 1.3.6.1.4.1.3902.15.2.11.2.4.1.7 | ColumnportOperDuplex | read-only | current | The actual port duplex mode |
| 1.3.6.1.4.1.3902.15.2.11.2.4.1.8 | ColumnportOperSpeed | read-only | current | The actual port speed |
| 1.3.6.1.4.1.3902.15.2.11.2.4.1.9 | ColumnportPvid | read-write | current | Port default vlan id |
| 1.3.6.1.4.1.3902.15.2.11.2.4.1.10 | ColumnportFlowControl | read-write | current | Port's flowcontrol |
| 1.3.6.1.4.1.3902.15.2.11.2.4.1.11 | ColumnportVlanMode | read-write | current | Port's vlan-mode .(only valid in the pon port) . The first character means: 1 : port's vlan-mode for transparent-mode . 2 : port's vlan-mode for translation-mo… |
| 1.3.6.1.4.1.3902.15.2.11.2.4.1.12 | ColumnportSecurity | read-write | current | Port mac-address learning. PortSecurity enabled means forbid this port learning mac-address, whereas permit mac-address self-learning. |
| 1.3.6.1.4.1.3902.15.2.11.2.4.1.13 | ColumnportPriority | read-write | current | Port's priority |
| 1.3.6.1.4.1.3902.15.2.11.2.4.1.14 | ColumnportMulticast | read-write | current | Port forward or discard multicast packet. |
| 1.3.6.1.4.1.3902.15.2.11.2.4.1.15 | ColumnportMediaType | read-only | current | Media type of the port. |
| 1.3.6.1.4.1.3902.15.2.11.2.4.1.16 | ColumnisPortInTrunk | read-only | current | This item indicates whether a port has been added to a trunk or not. |
| 1.3.6.1.4.1.3902.15.2.11.2.4.1.17 | ColumnportLoopdetectStatus | read-only | current | Loopdetect status of the port.The first character means: 0 : port_notInTrunk_down 1 : port_notInTrunk_up_loopdetDisable 2 : port_notInTrunk_up_loopdetEnable_no… |
| 1.3.6.1.4.1.3902.15.2.11.2.4.1.18 | ColumndynamicMacMaxCount | read-write | current | Port's sum of dynamic macaddress. |
| 1.3.6.1.4.1.3902.15.2.11.2.5 | NotificationdynamicMacExceedTrap | current | The trap indicates dynamic macaddress exceed the limit set for the port. | |
| 1.3.6.1.4.1.3902.15.2.11.3 | Nodevlan | |||
| 1.3.6.1.4.1.3902.15.2.11.3.1 | ScalarmaxVlanId | read-only | current | Max vlan id. |
| 1.3.6.1.4.1.3902.15.2.11.3.2 | ScalarmaxSupportedVlans | read-only | current | The maximum number of IEEE 802.1Q VLANs that this device supports. |
| 1.3.6.1.4.1.3902.15.2.11.3.3 | TablevlanTable | not-accessible | current | A table containing static config information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be r… |
| 1.3.6.1.4.1.3902.15.2.11.3.3.1 | RowvlanEntry | not-accessible | current | Each entry contains all config of a vlan. |
| 1.3.6.1.4.1.3902.15.2.11.3.3.1.1 | ColumnvlanId | not-accessible | current | Vlan id |
| 1.3.6.1.4.1.3902.15.2.11.3.3.1.3 | ColumnvlanUntaggedPorts | read-write | current | Untagged ports in this vlan. |
| 1.3.6.1.4.1.3902.15.2.11.3.3.1.4 | ColumnvlanTaggedPorts | read-write | current | Tagged ports in this vlan. |
| 1.3.6.1.4.1.3902.15.2.11.3.3.1.5 | ColumnvlanName | read-write | current | Descriptive name of the vlan. |
| 1.3.6.1.4.1.3902.15.2.11.3.3.1.6 | ColumnvlanAdminStatus | read-write | current | The desired state of the vlan. |
| 1.3.6.1.4.1.3902.15.2.11.3.3.1.7 | ColumnvlanUntaggedTrunks | read-write | current | Untagged trunk in the vlan |
| 1.3.6.1.4.1.3902.15.2.11.3.3.1.8 | ColumnvlanTaggedTrunks | read-write | current | Tagged trunks in the vlan |
| 1.3.6.1.4.1.3902.15.2.11.3.4 | TablevlanAssistantTable | not-accessible | current | Vlan in this table means that vlan is enabled or has a descriptive name or contains ports/trunks. |
| 1.3.6.1.4.1.3902.15.2.11.3.4.1 | RowvlanAssistantEntry | not-accessible | current | Row Description |
| 1.3.6.1.4.1.3902.15.2.11.3.4.1.1 | ColumnassVlanId | read-only | current | Vlan id |
| 1.3.6.1.4.1.3902.15.2.11.4 | Nodemirror | |||
| 1.3.6.1.4.1.3902.15.2.11.4.1 | ScalarsourcePortsIngress | read-write | current | Mirroring source ports for ingress |
| 1.3.6.1.4.1.3902.15.2.11.4.2 | ScalarsourcePortsEgress | read-write | current | Mirroring source ports for egress |
| 1.3.6.1.4.1.3902.15.2.11.4.3 | ScalardesPortIngress | read-write | current | Mirroring destination port for ingress. Each device has only one . |
| 1.3.6.1.4.1.3902.15.2.11.4.4 | ScalardesPortEgress | read-write | current | Mirroring destination port for egress. Each device has only one . |
| 1.3.6.1.4.1.3902.15.2.11.5 | Nodeqos | |||
| 1.3.6.1.4.1.3902.15.2.11.5.1 | ScalarqueueScheduleWeight | read-write | current | The item is only valid for fePorts. The format is W0-W1-W2-W3.Each takes the value of 1-32. For Example : 2-3-4-5 means queue0-weight :2; queue1-weight :3; que… |
| 1.3.6.1.4.1.3902.15.2.11.5.2 | ScalarqueueScheduleMode0 | read-only | current | The item is only valid for fePorts. The format is W0-W1-W2-W3. Each takes the value of 1-32, which means wrr mode; or 0,which means sp mode. For Example : 1-2-… |
| 1.3.6.1.4.1.3902.15.2.11.5.3 | ScalarqueueScheduleMode1 | read-only | current | The item is only valid for fePorts. The format is W0-W1-W2-W3. Each takes the value of 1-32, which means wrr mode; or 0,which means sp mode. For Example : 0-0-… |
| 1.3.6.1.4.1.3902.15.2.11.5.4 | ScalarqueueScheduleMode2 | read-only | current | The item is only valid for fePorts. The format is W0-W1-W2-W3. Each takes the value of 1-32, which means wrr mode; or 0,which means sp mode. For Example : 1-2-… |
| 1.3.6.1.4.1.3902.15.2.11.5.5 | ScalarqueueScheduleMode3 | read-only | current | The item is only valid for fePorts. The format is W0-W1-W2-W3. Each takes the value of 1-32, which means wrr mode; or 0,which means sp mode. For Example : 1-2-… |
| 1.3.6.1.4.1.3902.15.2.11.5.6 | ScalarqosPrimapUsrToTraffic | read-write | current | For fePort,qos priority-map includes user-priority to traffic-class. The format of this item is array of eight traffic-class values corresponding to 0-7 user-p… |
| 1.3.6.1.4.1.3902.15.2.11.5.7 | TableqosPolicerTable | not-accessible | current | Description |
| 1.3.6.1.4.1.3902.15.2.11.5.7.1 | RowqosPolicerEntry | not-accessible | current | Row Description |
| 1.3.6.1.4.1.3902.15.2.11.5.7.1.1 | ColumnpolicerID | not-accessible | current | Column Description.The scope is 0-255. |
| 1.3.6.1.4.1.3902.15.2.11.5.7.1.2 | ColumnqosPolicerPara | read-write | current | qosGlobalProfile setting.If 0 means the policer is not existed. The valid scope is 32-25165824,which means 32K-24Gbps. |
| 1.3.6.1.4.1.3902.15.2.11.5.7.1.3 | ColumnqosExceededOper | read-write | current | no-operation means no operation on the packets; drop means drop the packets. Notice:This item is valid only after qosPolicerPara is valid. |
| 1.3.6.1.4.1.3902.15.2.11.5.7.1.4 | ColumnqosPolicerBurst | read-write | current | qosGlobalProfile setting for burstSize.If 0 get,means the policer is not existed. The item can be set only after qosPolicerPara is valid. The valid scope is 20… |
| 1.3.6.1.4.1.3902.15.2.11.5.8 | TableipPriToTrafficTable | not-accessible | current | Description |
| 1.3.6.1.4.1.3902.15.2.11.5.8.1 | RowipPriToTrafficEntry | not-accessible | current | Row Description |
| 1.3.6.1.4.1.3902.15.2.11.5.8.1.1 | ColumnipPriority | not-accessible | current | Column Description |
| 1.3.6.1.4.1.3902.15.2.11.5.8.1.2 | ColumntcFePort | read-write | current | traffic-class corresponding to ipPriority. The value is between 0 and 3. |
| 1.3.6.1.4.1.3902.15.2.11.5.8.1.3 | ColumntcGePort | read-write | current | traffic-class corresponding to ipPriority. The value is between 0 and 7. |
| 1.3.6.1.4.1.3902.15.2.11.5.9 | TablefePortIngBandTable | not-accessible | current | A list of port entries. The number of entries is given by the value of portNumber. |
| 1.3.6.1.4.1.3902.15.2.11.5.9.1 | RowfePortIngBandEntry | not-accessible | current | A port entry containing objects at the subnetwork layer and below for a particular port. |
| 1.3.6.1.4.1.3902.15.2.11.5.9.1.1 | ColumnfePortID | read-only | current | The port ID.The value is devID*100+localPort. For example, 802 means devID is 8 and localPort is 2. |
| 1.3.6.1.4.1.3902.15.2.11.5.9.1.2 | ColumnsessionNo | read-only | current | The session No.The scope is 0-3. 0 means broadcast suppression; 1 means multicast suppression; 2 means rate limit; 3 means user configure. |
| 1.3.6.1.4.1.3902.15.2.11.5.9.1.3 | ColumnsessionStatus | read-write | current | Enable or disable the feport's ingress bandwidth session. Note��the item can be set to be enable only after feIngressRate has configed. |
| 1.3.6.1.4.1.3902.15.2.11.5.9.1.4 | ColumnfeIngressRate | read-write | current | feport's ingress bandwidth rate value(kbps). The scope is 64-100000 . |
| 1.3.6.1.4.1.3902.15.2.11.5.9.1.5 | ColumnfeIngressPkType | read-write | current | The item show status of packet type . In turn means unknownmulticast(1),broadcast(2),multicast(3),unicast(4), MGMT(5),ARP(6),tcp-control(7),tcp-data(8),udp(9),… |
| 1.3.6.1.4.1.3902.15.2.11.5.9.1.6 | ColumnquePriorityStatus | read-write | current | The item show status of queue-priority . In turn means queues-priority 0,1,2,3; 0 means disable,1 means enable. |
| 1.3.6.1.4.1.3902.15.2.11.5.9.1.7 | ColumnmgmtNoRatelimitStatus | read-write | current | Enable or disable mgmtNoRatelimit |
| 1.3.6.1.4.1.3902.15.2.11.5.10 | TablegePortIngBandTable | not-accessible | current | A list of port entries. The number of entries is given by the value of portNumber. |
| 1.3.6.1.4.1.3902.15.2.11.5.10.1 | RowgePortIngBandEntry | not-accessible | current | A port entry containing objects at the subnetwork layer and below for a particular port. |
| 1.3.6.1.4.1.3902.15.2.11.5.10.1.1 | ColumngePortID | read-only | current | The port ID.The value is devID*100+localPort. For example, 802 means devID is 8 and localPort is 2. |
| 1.3.6.1.4.1.3902.15.2.11.5.10.1.2 | ColumngeIngressStatus | read-write | current | Set geport's ingress bandwidth on or off. Note��the item can be set to be enable only after geIngressRate has configed. |
| 1.3.6.1.4.1.3902.15.2.11.5.10.1.3 | ColumngeIngressRate | read-write | current | The item show ingress rate for gigabit ethernet port . 2000-1000000 means valid ingress bandwidth. |
| 1.3.6.1.4.1.3902.15.2.11.5.10.1.4 | ColumngeIngressPkType | read-write | current | The item show status of packet type . In turn means unicast(1),nounicast(2),multicast(3),broadcast(4); 0 means disable,1 means enable. |
| 1.3.6.1.4.1.3902.15.2.11.5.11 | TablegeQueScheTable | not-accessible | current | Description |
| 1.3.6.1.4.1.3902.15.2.11.5.11.1 | RowgeQueScheEntry | not-accessible | current | Row Description |
| 1.3.6.1.4.1.3902.15.2.11.5.11.1.1 | ColumngePortSessionID | not-accessible | current | Column Description |
| 1.3.6.1.4.1.3902.15.2.11.5.11.1.2 | ColumnqueueID | not-accessible | current | Queue ID |
| 1.3.6.1.4.1.3902.15.2.11.5.11.1.3 | ColumnqueueSchedule | read-write | current | The format is X-Y. X :1,means strict priority mode,Y is not necessary; 2,means sdwrr mode and group 0; 3,means sdwrr mode and group 1. Y :queue weight,1-32. No… |
| 1.3.6.1.4.1.3902.15.2.11.5.12 | ScalargeQosPrimapUsrToTraffic | read-write | current | For gePort,qos priority-map includes user-priority to traffic-class. The format of this item is array of eight traffic-class values corresponding to 0-7 user-p… |
| 1.3.6.1.4.1.3902.15.2.11.5.13 | TablegePortIp2UserTable | not-accessible | current | Description |
| 1.3.6.1.4.1.3902.15.2.11.5.13.1 | RowgePortIp2UserEntry | not-accessible | current | Row Description |
| 1.3.6.1.4.1.3902.15.2.11.5.13.1.2 | ColumnuserPriority | read-write | current | For gePort,userPriority corresponding to ipPriority. The value is between 0 and 7. |
| 1.3.6.1.4.1.3902.15.2.11.5.14 | TableportQosParamTable | not-accessible | current | A list of port entries. The number of entries is given by the value of portNumber. |
| 1.3.6.1.4.1.3902.15.2.11.5.14.1 | RowportQosParamEntry | not-accessible | current | A port entry containing objects at the subnetwork layer and below for a particular port. |
| 1.3.6.1.4.1.3902.15.2.11.5.14.1.1 | ColumnportID | not-accessible | current | The port ID.The value is devID*100+localPort. For example, 802 means devID is 8 and localPort is 2. |
| 1.3.6.1.4.1.3902.15.2.11.5.14.1.2 | ColumnbandWidthEgress | read-write | current | port's egress bandwidth restrict, The format is 0 or R-BR. 0 means clear the port's original egress bandwidth config. For fePort: R:means rate ,the scope is 64… |
| 1.3.6.1.4.1.3902.15.2.11.5.14.1.3 | ColumnupPriorityEnable | read-write | current | Enable or disable userPriority. |
| 1.3.6.1.4.1.3902.15.2.11.5.14.1.4 | ColumndscpPriorityEnable | read-write | current | Enable or disable dscpPriority |
| 1.3.6.1.4.1.3902.15.2.11.5.14.1.5 | ColumnqueScheduleMode | read-write | current | Port's queue-schedule mode. For fePort: wrr0 means Weight0-weight1-weight2-weight3; sp means SP-SP-SP-SP; wrr1-sp means Weight0-weight1-weight2-sp; wrr2-sp mea… |
| 1.3.6.1.4.1.3902.15.2.11.5.14.1.6 | ColumnremaptagToPriority | read-write | current | Qos priority-map includes remappingtag to traffic-class. The format of this item is array of eight traffic-class values corresponding to 0-7 remappingtag. Each… |
| 1.3.6.1.4.1.3902.15.2.11.6 | Nodepvlan | |||
| 1.3.6.1.4.1.3902.15.2.11.6.1 | ScalarsessionMaxNum | read-only | current | Pvlan session max num,default 4. |
| 1.3.6.1.4.1.3902.15.2.11.6.2 | TablepvlanTable | not-accessible | current | A list of pvlan entries. The number of entries is given by the value of session number. |
| 1.3.6.1.4.1.3902.15.2.11.6.2.1 | RowpvlanEntry | not-accessible | current | A pvlan entry . |
| 1.3.6.1.4.1.3902.15.2.11.6.2.1.1 | ColumnsessionId | not-accessible | current | The server id |
| 1.3.6.1.4.1.3902.15.2.11.6.2.1.2 | ColumnproAndIsoPortOrTrunk | read-write | current | pvlan setting including promiscuous port(or trunk) and isolated port(or ports). The format is 0 or Px-xxxxxxxx or Tx-xxxxxxxx. if 0 means no pvlan config.Other… |
| 1.3.6.1.4.1.3902.15.2.11.7 | Nodelacp | |||
| 1.3.6.1.4.1.3902.15.2.11.7.1 | ScalarlacpAdminStatus | read-write | current | The desired state of Link Aggregation Control Protocol(LACP). |
| 1.3.6.1.4.1.3902.15.2.11.7.2 | ScalarlacpPriority | read-write | current | LACP priority value. |
| 1.3.6.1.4.1.3902.15.2.11.7.3 | ScalartrunkNumber | read-only | current | The number of trunks (regardless of their current state) present on this system. |
| 1.3.6.1.4.1.3902.15.2.11.7.4 | TabletrunkTable | not-accessible | current | A table of all trunks' config. |
| 1.3.6.1.4.1.3902.15.2.11.7.4.1 | RowtrunkEntry | not-accessible | current | Each entry contains config of a trunk. |
| 1.3.6.1.4.1.3902.15.2.11.7.4.1.1 | ColumntrunkId | not-accessible | current | Trunk id. |
| 1.3.6.1.4.1.3902.15.2.11.7.4.1.2 | ColumntrunkPvid | read-write | current | Trunk default vlan id. |
| 1.3.6.1.4.1.3902.15.2.11.7.4.1.3 | ColumntrunkMulticast | read-write | current | Trunk forward/discard multicast packet. |
| 1.3.6.1.4.1.3902.15.2.11.7.4.1.4 | ColumntrunkPorts | read-write | current | Ports in lacp link aggregation group. |
| 1.3.6.1.4.1.3902.15.2.11.7.4.1.5 | ColumntrunkMode | read-write | current | Aggregator mode |
| 1.3.6.1.4.1.3902.15.2.11.7.5 | TablelacpPortTable | not-accessible | current | The table of all ports' config for LACP. |
| 1.3.6.1.4.1.3902.15.2.11.7.5.1 | RowlacpPortEntry | not-accessible | current | Each entry contains port config for LACP. |
| 1.3.6.1.4.1.3902.15.2.11.7.5.1.1 | ColumnlacpPortId | not-accessible | current | The port id to index lacp config. |
| 1.3.6.1.4.1.3902.15.2.11.7.5.1.2 | ColumnlacpPortMode | read-write | current | Port's aggregator mode in LACP |
| 1.3.6.1.4.1.3902.15.2.11.7.5.1.3 | ColumnlacpPortTimeout | read-write | current | LACP aggregator timeout |
| 1.3.6.1.4.1.3902.15.2.11.8 | Nodelayer3 | |||
| 1.3.6.1.4.1.3902.15.2.11.8.1 | Tablelayer3PortTable | not-accessible | current | The layer 3 port table contains config of all layer 3 ports of the device. |
| 1.3.6.1.4.1.3902.15.2.11.8.1.1 | Rowlayer3PortEntry | not-accessible | current | An entry of layer 3 port config |
| 1.3.6.1.4.1.3902.15.2.11.8.1.1.1 | Columnlayer3PortId | not-accessible | current | Layer 3 port id |
| 1.3.6.1.4.1.3902.15.2.11.8.1.1.2 | Columnlayer3PortIpAddrAndMask | read-write | current | the format of this item is xx.xx.xx.xx/xx. Among this string, the first segment represents layer 3 ipAddress, the second segment represents net mask. eg: 192.1… |
| 1.3.6.1.4.1.3902.15.2.11.8.1.1.3 | Columnlayer3PortMacAddr | read-write | current | Mac address of a layer 3 port. The scope of zte mac is 00:d0:d0:f0:00:00~00:d0:d0:ff:ff:ff. |
| 1.3.6.1.4.1.3902.15.2.11.8.1.1.4 | Columnlayer3PortVlanId | read-write | current | Vlan id binded to a layer 3 port. |
| 1.3.6.1.4.1.3902.15.2.11.8.1.1.5 | Columnlayer3PortAdminStatus | read-write | current | The desired state of the layer 3 port. |
| 1.3.6.1.4.1.3902.15.2.11.9 | NodeloopDetect | |||
| 1.3.6.1.4.1.3902.15.2.11.9.1 | ScalarloopDetectBlockDelay | read-write | current | Loopback block delay interval(minute). After delay-interval, the trunk or port blocked because of loopback will be unblocked. |
| 1.3.6.1.4.1.3902.15.2.11.9.2 | ScalarloopDetectSendPktInterval | read-write | current | Loopback block send packet interval(second). |
| 1.3.6.1.4.1.3902.15.2.11.9.3 | TableloopDetectPortTable | not-accessible | current | Loopback detection config and result of trunks. |
| 1.3.6.1.4.1.3902.15.2.11.9.3.1 | RowloopDetectPortEntry | not-accessible | current | A port entry containing loopback detection config and status. |
| 1.3.6.1.4.1.3902.15.2.11.9.3.1.1 | ColumnloopDetectPortId | read-only | current | Port id. |
| 1.3.6.1.4.1.3902.15.2.11.9.3.1.2 | ColumnloopDetectPortAdminStatus | read-write | current | This item indicates whether permit loop back detection on this port or not.The first character means: 0-disable;1:enable(port based);2:enable(vlan based); The … |
| 1.3.6.1.4.1.3902.15.2.11.9.3.1.3 | ColumnloopDetectPortProtectStatus | read-write | current | Whether block this port or not while detect loopback. |
| 1.3.6.1.4.1.3902.15.2.11.9.3.1.4 | ColumnloopDetectPortLoopStatus | read-only | current | Item value indicates whether this port is loopback. |
| 1.3.6.1.4.1.3902.15.2.11.9.3.1.5 | ColumnloopDetectPortBlockStatus | read-only | current | Item value indicates whether this port is blocked. |
| 1.3.6.1.4.1.3902.15.2.11.9.3.1.6 | ColumnloopDetectPortInVlan | read-only | current | VlanID which the port belong to when looped and blocked. 0 means default vlanID which the port is in when looped and blocked; 1-4094 means some vlanID which th… |
| 1.3.6.1.4.1.3902.15.2.11.9.4 | TableloopDetectTrunkTable | not-accessible | current | Loopback detection config and result of trunks. |
| 1.3.6.1.4.1.3902.15.2.11.9.4.1 | RowloopDetectTrunkEntry | not-accessible | current | A trunk entry containing loopback detection config and status. |
| 1.3.6.1.4.1.3902.15.2.11.9.4.1.1 | ColumnloopDetectTrunkId | read-only | current | Trunk id. |
| 1.3.6.1.4.1.3902.15.2.11.9.4.1.2 | ColumnloopDetectTrunkAdminStatus | read-write | current | This item indicates whether permit loopback detection on this trunk or not.The first character means: 0-disable;1:enable(trunk based);2:enable(vlan based); The… |
| 1.3.6.1.4.1.3902.15.2.11.9.4.1.3 | ColumnloopDetectTrunkProtectStatus | read-write | current | Whether block this trunk or not while detect loopback. |
| 1.3.6.1.4.1.3902.15.2.11.9.4.1.4 | ColumnloopDetectTrunkLoopStatus | read-only | current | Item value indicates whether this trunk is loopback. |
| 1.3.6.1.4.1.3902.15.2.11.9.4.1.5 | ColumnloopDetectTrunkBlockStatus | read-only | current | Item value indicates whether this trunk is blocked. |
| 1.3.6.1.4.1.3902.15.2.11.9.4.1.6 | ColumnloopDetectTrunkInVlan | read-only | current | VlanID which the trunk belong to when looped and blocked. 0 means default vlanID which the trunk is in when looped and blocked; 1-4094 means some vlanID which … |
| 1.3.6.1.4.1.3902.15.2.11.9.5 | NotificationloopDetectPortTrap | current | The trap indicates nms that port based loopdetect status. | |
| 1.3.6.1.4.1.3902.15.2.11.9.6 | NotificationloopDetectTrunkTrap | current | The trap indicates nms that trunk based loopdetect status. | |
| 1.3.6.1.4.1.3902.15.2.11.10 | NodevlanTranslation | |||
| 1.3.6.1.4.1.3902.15.2.11.10.1 | TablevlanTranslationTable | not-accessible | current | Description vlan-translation . |
| 1.3.6.1.4.1.3902.15.2.11.10.1.1 | RowvlanTranslationEntry | not-accessible | current | Description |
| 1.3.6.1.4.1.3902.15.2.11.10.1.1.1 | ColumningressPortId | read-only | current | feport id |
| 1.3.6.1.4.1.3902.15.2.11.10.1.1.2 | ColumnvlanTranslationEnable | read-write | current | vlan-translation state . |
| 1.3.6.1.4.1.3902.15.2.11.10.1.1.3 | ColumnvlanTranslationStatus | read-write | current | This item indicates whether permit vlan-translation on this port or not. The format is INV/EGP/EGV or 0. 0 : means clear vlan-translation on the port. INV : me… |
| 1.3.6.1.4.1.3902.15.2.11.11 | Nodestp | |||
| 1.3.6.1.4.1.3902.15.2.11.11.1 | ScalarstpAdminStatus | read-write | current | Description |
| 1.3.6.1.4.1.3902.15.2.11.12 | Nodevct | |||
| 1.3.6.1.4.1.3902.15.2.11.12.1 | TablevctPortTable | not-accessible | current | The table of all ports' virtual cable test. |
| 1.3.6.1.4.1.3902.15.2.11.12.1.1 | RowvctPortEntry | not-accessible | current | Each entry contains port config for VCT. |
| 1.3.6.1.4.1.3902.15.2.11.12.1.1.1 | ColumnvctPortId | not-accessible | current | The port id to index vct config. |
| 1.3.6.1.4.1.3902.15.2.11.12.1.1.2 | ColumnvctDo | read-write | current | The value get from this item is insignificant. Setting this item will start a virtual cable test process. |
| 1.3.6.1.4.1.3902.15.2.11.12.1.1.3 | ColumnvctIsValid | read-only | current | This item indicates whether the port surports vct or whether the result is valid. yes2 means there are 2 pairs, yes4 means there are 4 pairs. |
| 1.3.6.1.4.1.3902.15.2.11.12.1.1.4 | ColumnvctPair1Result | read-only | current | This item indicates the cable status: open, short or impedance mismatch. |
| 1.3.6.1.4.1.3902.15.2.11.12.1.1.5 | ColumnvctPair1Lenth | read-only | current | This item indicates fault position. |
| 1.3.6.1.4.1.3902.15.2.11.12.1.1.6 | ColumnvctPair2Result | read-only | current | This item indicates the cable status: open, short or impedance mismatch. |
| 1.3.6.1.4.1.3902.15.2.11.12.1.1.7 | ColumnvctPair2Lenth | read-only | current | This item indicates fault position. |
| 1.3.6.1.4.1.3902.15.2.11.12.1.1.8 | ColumnvctPair3Result | read-only | current | This item indicates the cable status: open, short or impedance mismatch. |
| 1.3.6.1.4.1.3902.15.2.11.12.1.1.9 | ColumnvctPair3Lenth | read-only | current | This item indicates fault position. |
| 1.3.6.1.4.1.3902.15.2.11.12.1.1.10 | ColumnvctPair4Result | read-only | current | This item indicates the cable status: open, short or impedance mismatch. |
| 1.3.6.1.4.1.3902.15.2.11.12.1.1.11 | ColumnvctPair4Lenth | read-only | current | This item indicates fault position. |
| 1.3.6.1.4.1.3902.15.2.11.13 | Nodesyslog | |||
| 1.3.6.1.4.1.3902.15.2.11.13.1 | ScalarsyslogStatus | read-write | current | Syslog status :enable or disable |
| 1.3.6.1.4.1.3902.15.2.11.13.2 | ScalarsyslogLevel | read-write | current | Syslog level: 0 Emergency: system is unusable 1 Alert: action must be taken immediately 2 Critical: critical conditions 3 Error: error conditions 4 Warning: wa… |
| 1.3.6.1.4.1.3902.15.2.11.13.3 | ScalarenabledModule | read-write | current | Syslog enabled module,Only 9,26,27,29 can be supported now. 0-driver;1-vct;2-inter;3-8021x;4-groupman 5-igmpsnp;6-lacp;7-loopdet;8-mstp;9-radius 10-syslog;11-f… |
| 1.3.6.1.4.1.3902.15.2.11.13.4 | ScalarserverMaxNum | read-only | current | Syslog server max num,default 5. |
| 1.3.6.1.4.1.3902.15.2.11.13.5 | TableserverTable | not-accessible | current | A list of server entries. The number of entries is given by the value of serverNumber. |
| 1.3.6.1.4.1.3902.15.2.11.13.5.1 | RowserverEntry | not-accessible | current | A server entry . |
| 1.3.6.1.4.1.3902.15.2.11.13.5.1.1 | ColumnserverId | not-accessible | current | The server id |
| 1.3.6.1.4.1.3902.15.2.11.13.5.1.2 | ColumnserverIP | read-write | current | the format of this item is xx.xx.xx.xx. eg: 192.168.2.8. The value must be valid ipaddress.Others 0 means delete primary IP address . |
| 1.3.6.1.4.1.3902.15.2.11.13.5.1.3 | ColumnserverName | read-write | current | Server name valid only as serverAdminStatus is enable. |
| 1.3.6.1.4.1.3902.15.2.11.13.5.1.4 | ColumnserverAdminStatus | read-only | current | The desired state of syslog server. |
| 1.3.6.1.4.1.3902.15.2.11.14 | Nodentp | |||
| 1.3.6.1.4.1.3902.15.2.11.14.1 | ScalarsynchronizeStatus | read-only | current | Ntp synchronize status |
| 1.3.6.1.4.1.3902.15.2.11.14.2 | ScalarprotocolStatus | read-write | current | Ntp protocol status |
| 1.3.6.1.4.1.3902.15.2.11.14.3 | ScalarsrvIpAddrAndVersion | read-write | current | the format of this item is xx.xx.xx.xx-x. Among this string, the first segment represents ntp server ipAddress, the value 0.0.0.0 is invalid; the second segmen… |
| 1.3.6.1.4.1.3902.15.2.11.14.4 | ScalarsourceIpAddr | read-write | current | represents ntp source ipAddress. IP Address 0.0.0.0 is also valid. |
| 1.3.6.1.4.1.3902.15.2.11.15 | NodeloginUser | |||
| 1.3.6.1.4.1.3902.15.2.11.15.1 | TableuserTable | not-accessible | current | A table containing loginUser configuration. |
| 1.3.6.1.4.1.3902.15.2.11.15.1.1 | RowuserEntry | not-accessible | current | Each entry contains all config of an user. |
| 1.3.6.1.4.1.3902.15.2.11.15.1.1.1 | ColumnuserName | read-only | current | Community name .The character '?' is forbidded. |
| 1.3.6.1.4.1.3902.15.2.11.15.1.1.2 | ColumnuserAttr | read-write | current | User attribute.'1' means clear the user. |
| 1.3.6.1.4.1.3902.15.2.11.15.1.1.3 | ColumnloginPass | read-write | current | Login password which attached to user.The character '?' is forbidded. |
| 1.3.6.1.4.1.3902.15.2.11.15.1.1.4 | ColumnadminPass | read-write | current | Admin password which attached to user.The character '?' is forbidded. |
| 1.3.6.1.4.1.3902.15.2.11.16 | NodesnmpConfig | |||
| 1.3.6.1.4.1.3902.15.2.11.16.1 | TablecommunityTable | not-accessible | current | A table containing snmp community configuration. |
| 1.3.6.1.4.1.3902.15.2.11.16.1.1 | RowcommunityEntry | not-accessible | current | Each entry contains all config of a community. |
| 1.3.6.1.4.1.3902.15.2.11.16.1.1.1 | ColumncommunityName | read-only | current | Community name . |
| 1.3.6.1.4.1.3902.15.2.11.16.1.1.2 | ColumncommunityAttr | read-write | current | Community attribute.'1' means clear the community. |
| 1.3.6.1.4.1.3902.15.2.11.16.1.1.3 | ColumnviewAttached | read-write | current | View which attached to community. |
| 1.3.6.1.4.1.3902.15.2.11.16.2 | TableviewTable | not-accessible | current | A table containing snmp view configuration. |
| 1.3.6.1.4.1.3902.15.2.11.16.2.1 | RowviewEntry | not-accessible | current | Each entry contains all config of a view. |
| 1.3.6.1.4.1.3902.15.2.11.16.2.1.1 | ColumnviewIndex | not-accessible | current | Index of the view table . The scope is 1-32 . The value get from this item is insignificant. |
| 1.3.6.1.4.1.3902.15.2.11.16.2.1.2 | ColumnviewName | read-only | current | View name . |
| 1.3.6.1.4.1.3902.15.2.11.16.2.1.3 | ColumnattrAndOid | read-write | current | View attribute and OID which attached to view. The set value is not always equal with the get value. The format is 0 or x-y or 3.x is 1,which means include, 2 … |
| 1.3.6.1.4.1.3902.15.2.11.16.3 | TabletrapHostTable | not-accessible | current | A table containing snmp traphost configuration. |
| 1.3.6.1.4.1.3902.15.2.11.16.3.1 | RowtrapHostEntry | not-accessible | current | Each entry contains all config of a traphost. |
| 1.3.6.1.4.1.3902.15.2.11.16.3.1.1 | ColumntraphostIP | not-accessible | current | Traphost IPAddress . |
| 1.3.6.1.4.1.3902.15.2.11.16.3.1.2 | ColumntraphostType | not-accessible | current | Host type. 1: trap ; 2: inform . |
| 1.3.6.1.4.1.3902.15.2.11.16.3.1.3 | ColumncommuName | read-only | current | SNMPv3 user name |
| 1.3.6.1.4.1.3902.15.2.11.16.3.1.4 | ColumntraphostVer | read-write | current | Traphost Version. 0: clear the traphost config; 1: version 1;(only valid in the trap type). 2: version 2c; 3: version 3 using the AuthNoPriv security level; 4:… |
| 1.3.6.1.4.1.3902.15.2.11.16.4 | ScalartrapEnable | read-write | current | Set trap message enable or disable.The message is the following in turn: 1.coldStartTrap;2.warmStartTrap;3.linkDownTrap;4.linkUpTrap; 5. authFailTrap;6.topolog… |
| 1.3.6.1.4.1.3902.15.2.11.17 | Nodeacl | |||
| 1.3.6.1.4.1.3902.15.2.11.17.1 | TabletimeAclTable | not-accessible | current | A table containing time configuration for acl . |
| 1.3.6.1.4.1.3902.15.2.11.17.1.1 | RowtimeAclEntry | not-accessible | current | Each entry contains all config of basic acl. |
| 1.3.6.1.4.1.3902.15.2.11.17.1.1.1 | ColumntimeRangeName | not-accessible | current | Timerange ID . The scope is 1-16 characters. |
| 1.3.6.1.4.1.3902.15.2.11.17.1.1.2 | ColumntimeRange | read-write | current | The format is Z(YYYYMMDD(?)*hh:mm-YYYYMMDD(?)*hh:mm); Z takes the following value: 0:clear the timeRange ,no word followed; 1:monday; 2:tuesday; 3:wednesday; 4… |
| 1.3.6.1.4.1.3902.15.2.11.17.2 | TablebasicAclTable | not-accessible | current | A table containing basic acl configuration. |
| 1.3.6.1.4.1.3902.15.2.11.17.2.1 | RowbasicAclEntry | not-accessible | current | Each entry contains all config of basic acl. |
| 1.3.6.1.4.1.3902.15.2.11.17.2.1.1 | ColumnbasicACLNo | not-accessible | current | Basic acl number . The scope is 1-99. |
| 1.3.6.1.4.1.3902.15.2.11.17.2.1.2 | ColumnbasicRuleID | not-accessible | current | RuleID in Basic acl number mode. |
| 1.3.6.1.4.1.3902.15.2.11.17.2.1.3 | ColumnruleBasicStatus | read-write | current | When the ruleID is cleared ,the status is disable. |
| 1.3.6.1.4.1.3902.15.2.11.17.2.1.4 | ColumnruleBasicACL | read-write | current | Basic acl config. The format is X-A.B.C.D/N-F. X is 1:deny;2:permit; 'A.B.C.D/N'is source ip and mask.If 'x' means any; F : 0 means no fragment set;1 means fra… |
| 1.3.6.1.4.1.3902.15.2.11.17.3 | TableextendedAclTable | not-accessible | current | A table containing extended acl configuration. |
| 1.3.6.1.4.1.3902.15.2.11.17.3.1 | RowextendedAclEntry | not-accessible | current | Each entry contains all config of extended acl. |
| 1.3.6.1.4.1.3902.15.2.11.17.3.1.1 | ColumnextendedACLNo | not-accessible | current | Extended acl number .The scope is 100-199. |
| 1.3.6.1.4.1.3902.15.2.11.17.3.1.2 | ColumnextendedRuleID | not-accessible | current | RuleID in extended acl number mode. |
| 1.3.6.1.4.1.3902.15.2.11.17.3.1.3 | ColumnruleExtendedStatus | read-write | current | When the ruleID is cleared ,the status is disable. |
| 1.3.6.1.4.1.3902.15.2.11.17.3.1.4 | ColumnruleExtendedProtocol | read-write | current | Extended acl config for other protocol. The format is P:RULE. P means protocol value, P is IC,known as icmp(1) protocol, the format of RULE is X-A.B.C.D/N-A.B.… |
| 1.3.6.1.4.1.3902.15.2.11.17.4 | TablelinkAclTable | not-accessible | current | A table containing link acl configuration. |
| 1.3.6.1.4.1.3902.15.2.11.17.4.1 | RowlinkAclEntry | not-accessible | current | Each entry contains all config of link acl. |
| 1.3.6.1.4.1.3902.15.2.11.17.4.1.1 | ColumnlinkACLNo | not-accessible | current | Link acl number .The scope is 200-299. |
| 1.3.6.1.4.1.3902.15.2.11.17.4.1.2 | ColumnlinkRuleID | not-accessible | current | RuleID in link acl number mode . |
| 1.3.6.1.4.1.3902.15.2.11.17.4.1.3 | ColumnruleLinkStatus | read-write | current | When the ruleID is cleared ,the status is disable. |
| 1.3.6.1.4.1.3902.15.2.11.17.4.1.4 | ColumnruleLinkProtocol | read-write | current | Link acl config for protocol. The format is P:RULE. P means protocol value, P is I,known as ip protocol, the format of RULE is X-C-V-M-SM-DM; P is A,known as a… |
| 1.3.6.1.4.1.3902.15.2.11.17.5 | TablehybridAclTable | not-accessible | current | A table containing hybrid acl configuration. |
| 1.3.6.1.4.1.3902.15.2.11.17.5.1 | RowhybridAclEntry | not-accessible | current | Each entry contains all config of hybrid acl. |
| 1.3.6.1.4.1.3902.15.2.11.17.5.1.1 | ColumnhybridACLNo | not-accessible | current | Hybrid acl number .The scope is 300-399. |
| 1.3.6.1.4.1.3902.15.2.11.17.5.1.2 | ColumnhybridRuleID | not-accessible | current | RuleID in hybrid acl number mode. |
| 1.3.6.1.4.1.3902.15.2.11.17.5.1.3 | ColumnruleHybridStatus | read-write | current | When the ruleID is cleared ,the status is disable. |
| 1.3.6.1.4.1.3902.15.2.11.17.5.1.4 | ColumnruleHybridProtocol | read-write | current | Hybrid acl config. This table does not support IPV6. The format is P:RULE. P means protocol value, P is I,known as ip protocol, the format of RULE is X-A.B.C.D… |
| 1.3.6.1.4.1.3902.15.2.11.17.6 | TableglobalAclTable | not-accessible | current | A table containing global acl configuration. |
| 1.3.6.1.4.1.3902.15.2.11.17.6.1 | RowglobalAclEntry | not-accessible | current | Each entry contains all config of global acl. |
| 1.3.6.1.4.1.3902.15.2.11.17.6.1.1 | ColumnglobalACLNo | not-accessible | current | Global acl number(400) . |
| 1.3.6.1.4.1.3902.15.2.11.17.6.1.2 | ColumnglobalRuleID | not-accessible | current | RuleID in global acl number mode. The scope is 1-16 |
| 1.3.6.1.4.1.3902.15.2.11.17.6.1.3 | ColumnruleGlobalStatus | read-write | current | When the ruleID is cleared ,the status is disable. |
| 1.3.6.1.4.1.3902.15.2.11.17.6.1.4 | ColumnruleGlobalProtocol | read-write | current | Global acl config for protocol. The format is P:RULE. P means protocol value, P is I,known as ip protocol, the format of RULE is X-PI-A.B.C.D/N-A.B.C.D/N-D-F-C… |
| 1.3.6.1.4.1.3902.15.2.11.18 | Nodefdb | |||
| 1.3.6.1.4.1.3902.15.2.11.18.1 | ScalarfdbAgingTime | read-write | current | fdb aging time (unit:second).The deault value is 240. |
| 1.3.6.1.4.1.3902.15.2.11.18.2 | TablefdbFilterTable | not-accessible | current | A table that contains configuration and control information for each Filtering macaddress operating on this device. |
| 1.3.6.1.4.1.3902.15.2.11.18.2.1 | RowfdbFilterEntry | not-accessible | current | Information about a specific Filtering Database. |
| 1.3.6.1.4.1.3902.15.2.11.18.2.1.1 | ColumnfdbID | not-accessible | current | The identity of this Filtering Database. |
| 1.3.6.1.4.1.3902.15.2.11.18.2.1.2 | ColumnfdbFilterAddress | not-accessible | current | A filter MAC address for which the device has filtering information. |
| 1.3.6.1.4.1.3902.15.2.11.18.2.1.3 | ColumnfdbFilterType | read-write | current | The current type for the filtering macaddress. |
| 1.3.6.1.4.1.3902.15.2.11.18.3 | TablefdbStaticPortTable | not-accessible | current | A table that contains configuration and control information for each static macaddress operating on this device. |
| 1.3.6.1.4.1.3902.15.2.11.18.3.1 | RowfdbStaticPortEntry | not-accessible | current | Information about a specific Filtering Database. |
| 1.3.6.1.4.1.3902.15.2.11.18.3.1.2 | ColumnfdbStaticAddress | not-accessible | current | A filter MAC address for which the device has filtering information. |
| 1.3.6.1.4.1.3902.15.2.11.18.3.1.3 | ColumnportBindMac | read-write | current | The port id which binding macaddress and fid.If 0 means clear the fdb entry. |
| 1.3.6.1.4.1.3902.15.2.11.18.4 | TablefdbStaticTrunkTable | not-accessible | current | A table that contains configuration and control information for each static macaddress operating on this device. |
| 1.3.6.1.4.1.3902.15.2.11.18.4.1 | RowfdbStaticTrunkEntry | not-accessible | current | Information about a specific Filtering Database. |
| 1.3.6.1.4.1.3902.15.2.11.18.4.1.3 | ColumntrunkBindMac | read-write | current | The trunk id which binding macaddress and fid.If 0 means clear the fdb entry. |
| 1.3.6.1.4.1.3902.15.2.11.19 | Nodep8021xRelay | |||
| 1.3.6.1.4.1.3902.15.2.11.19.1 | Scalarp8021xRelayAdminStatus | read-write | current | Description |
| 1.3.6.1.4.1.3902.15.2.11.20 | NodeigmpSnooping | |||
| 1.3.6.1.4.1.3902.15.2.11.20.1 | TablemultiGroupTable | not-accessible | current | A list of pvlan entries. The number of entries is given by the value of session number. |
| 1.3.6.1.4.1.3902.15.2.11.20.1.1 | RowmultiGroupEntry | not-accessible | current | Multicast group entry. |
| 1.3.6.1.4.1.3902.15.2.11.20.1.1.1 | Columnnumber | not-accessible | current | The number of multicast group |
| 1.3.6.1.4.1.3902.15.2.11.20.1.1.2 | ColumnvlanID | read-only | current | Vlan id |
| 1.3.6.1.4.1.3902.15.2.11.20.1.1.3 | ColumnmultiGroup | read-only | current | Multicast group ipAddress |
| 1.3.6.1.4.1.3902.15.2.11.20.1.1.4 | ColumnportList | read-only | current | ports of the muliticast group |
| 1.3.6.1.4.1.3902.15.2.11.20.1.1.5 | ColumntrunkList | read-only | current | trunks of the muliticast group |
| 1.3.6.1.4.1.3902.15.2.11.21 | Nodeepon | |||
| 1.3.6.1.4.1.3902.15.2.11.21.2 | ScalarponReset | read-write | current | The value get from this item is insignificant. Setting this item will reset onu. |
| 1.3.6.1.4.1.3902.15.2.11.21.3 | NodeportPonInfo | |||
| 1.3.6.1.4.1.3902.15.2.11.21.3.1 | ScalarportPonAdminStatus | read-only | current | Port pon status . |
| 1.3.6.1.4.1.3902.15.2.11.21.3.2 | ScalarportPonStpState | read-only | current | Port pon stp state . |
| 1.3.6.1.4.1.3902.15.2.11.21.3.3 | ScalarportPonFecTx | read-only | current | Port pon Fec Tx . |
| 1.3.6.1.4.1.3902.15.2.11.21.3.4 | ScalarportPonFecRx | read-only | current | Port pon Fec Tx . |
| 1.3.6.1.4.1.3902.15.2.11.21.3.5 | ScalarportPonType | read-only | current | Port pon type. |
| 1.3.6.1.4.1.3902.15.2.11.21.3.6 | ScalarportPonOperStatus | read-only | current | Port pon oper status. |
| 1.3.6.1.4.1.3902.15.2.11.21.3.7 | ScalarportPonLlidPortsNum | read-only | current | Port pon llid ports num . |
| 1.3.6.1.4.1.3902.15.2.11.21.4 | NodeponOamInfo | |||
| 1.3.6.1.4.1.3902.15.2.11.21.4.1 | ScalarlocalOamAdmin | read-only | current | Pon local oam admin . |
| 1.3.6.1.4.1.3902.15.2.11.21.4.2 | ScalarlocalOamOper | read-only | current | Pon local oam oper . |
| 1.3.6.1.4.1.3902.15.2.11.21.4.3 | ScalarlocalOamMode | read-only | current | Pon local oam mode . |
| 1.3.6.1.4.1.3902.15.2.11.21.4.4 | ScalarlocalOamMaxPdu | read-only | current | Pon local oam max oampdu. |
| 1.3.6.1.4.1.3902.15.2.11.21.4.5 | ScalarlocalOamRevision | read-only | current | Pon local oam revision. |
| 1.3.6.1.4.1.3902.15.2.11.21.4.6 | ScalarlocalOamFuncSupport | read-only | current | Pon local oam funcsupport. |
| 1.3.6.1.4.1.3902.15.2.11.21.4.7 | ScalarpeerOamStatus | read-only | current | Pon peer oam status. |
| 1.3.6.1.4.1.3902.15.2.11.21.4.8 | ScalarpeerOamMacAddr | read-only | current | Pon peer oam macaddr . |
| 1.3.6.1.4.1.3902.15.2.11.21.4.9 | ScalarpeerOamOUI | read-only | current | Pon peer oam OUI . |
| 1.3.6.1.4.1.3902.15.2.11.21.4.10 | ScalarpeerOamVendor | read-only | current | Pon peer oam vendor. |
| 1.3.6.1.4.1.3902.15.2.11.21.4.11 | ScalarpeerOamMode | read-only | current | Pon peer oam mode . |
| 1.3.6.1.4.1.3902.15.2.11.21.4.12 | ScalarpeerOamMaxPdu | read-only | current | Pon peer oam max oampdu . |
| 1.3.6.1.4.1.3902.15.2.11.21.4.13 | ScalarpeerOamRevision | read-only | current | Pon peer oam revision. |
| 1.3.6.1.4.1.3902.15.2.11.21.4.14 | ScalarpeerOamFuncSupport | read-only | current | Pon peer oam funcsupport . |
| 1.3.6.1.4.1.3902.15.2.11.21.4.15 | ScalarponLoopbackStatus | read-only | current | Onu pon loopback status . |
| 1.3.6.1.4.1.3902.15.2.11.21.5 | NodeponFirmwareInfo | |||
| 1.3.6.1.4.1.3902.15.2.11.21.5.1 | ScalareponStatus | read-only | current | Epon status. |
| 1.3.6.1.4.1.3902.15.2.11.21.5.2 | ScalarsoftWareVersion | read-only | current | Epon software version . The format is MA.MI.RE-BU . |
| 1.3.6.1.4.1.3902.15.2.11.21.5.3 | ScalarloaderVersion | read-only | current | Epon loader version .The format is MA.MI.RE-BU . |
| 1.3.6.1.4.1.3902.15.2.11.21.5.4 | ScalarregisterOltInfo | read-only | current | Epon register olt information .The format is ID-LL-PP . |
| 1.3.6.1.4.1.3902.15.2.11.21.5.5 | ScalarregisterOnuInfo | read-only | current | Epon register onu information mac . The format is MA0:MA1:MA2:MA3:MA4:MA5-LL . |
| 1.3.6.1.4.1.3902.15.2.11.21.5.6 | ScalarportNum | read-only | current | Epon port num . |
| 1.3.6.1.4.1.3902.15.2.11.21.5.7 | Scalarregistered | read-only | current | Registered . |
| 1.3.6.1.4.1.3902.15.2.11.21.5.8 | Scalarauthenticated | read-only | current | Authenticated . |
| 1.3.6.1.4.1.3902.15.2.11.21.5.9 | ScalarponConfigMac | read-only | current | Pon config macaddr . |
| 1.3.6.1.4.1.3902.15.2.11.21.5.10 | ScalarmodeAndOamVer | read-only | current | Modes and Oam Version . |
| 1.3.6.1.4.1.3902.15.2.11.21.5.11 | ScalarmpcpTimeout | read-only | current | Mpcp Timeout . |
| 1.3.6.1.4.1.3902.15.2.11.21.5.12 | ScalarctrlVlan | read-only | current | Ctrl Vlan . |
| 1.3.6.1.4.1.3902.15.2.11.21.5.13 | ScalarvendPonUni | read-only | current | The format is VC-PC-UC . VC means vendor code value; PC means pon config value; UC means uni config value. |
| 1.3.6.1.4.1.3902.15.2.11.21.5.14 | ScalarctcOui | read-only | current | ctc Oui. |
| 1.3.6.1.4.1.3902.15.2.11.21.5.15 | ScalarctcVendor | read-only | current | Ctc Vendor |
| 1.3.6.1.4.1.3902.15.2.11.21.5.16 | ScalarctcModel | read-only | current | Ctc Model . |
| 1.3.6.1.4.1.3902.15.2.11.22 | NodeethernetOam | |||
| 1.3.6.1.4.1.3902.15.2.11.22.1 | ScalarethernetOamStatus | read-write | current | The desired state of the ethernetOam. |
| 1.3.6.1.4.1.3902.15.2.11.22.2 | ScalarethernetOamOuiDescr | read-write | current | Set organizationally unique identifier. The format of this item is xx-xx-xx, default:00-15-EB. |
| 1.3.6.1.4.1.3902.15.2.11.22.3 | ScalarorgSpecificTimeStamp | read-write | current | Set link event time stamp for link monitor. The scope is 1-10, default:10(100ms). |
| 1.3.6.1.4.1.3902.15.2.11.22.4 | ScalarremoteLoopbackTimeout | read-write | current | Set Ethernet Oam remote loopback timeout. The scope is 1-10, default:3(s). Suggest three times than loopback ports period. |
| 1.3.6.1.4.1.3902.15.2.11.22.5 | TableethernetOamIfConfigTable | not-accessible | current | Config port's ethernet oam. |
| 1.3.6.1.4.1.3902.15.2.11.22.5.1 | RowethernetOamIfConfigEntry | not-accessible | current | |
| 1.3.6.1.4.1.3902.15.2.11.22.5.1.2 | ColumnethernetOamIfStatus | read-write | current | Config port's ethernet oam enable or disable. |
| 1.3.6.1.4.1.3902.15.2.11.22.5.1.3 | ColumnremoteLoopbackIfStatus | read-write | current | start or stop port remote loopback. |
| 1.3.6.1.4.1.3902.15.2.11.22.5.1.4 | ColumnifPeriodTimeoutMode | read-write | current | set ethernet oam discovery period, link timeout and discovery mode. The format is P-T-M . P : set ethernet oam discovery period time. The scope is 1-10, defaul… |
| 1.3.6.1.4.1.3902.15.2.11.22.5.1.5 | ColumnifLinkMonitorStatus | read-write | current | Config link monitor enable or disable. |
| 1.3.6.1.4.1.3902.15.2.11.22.5.1.6 | ColumnifLinkSymbolPeriodThresholdWindow | read-write | current | Config link monitor symbol-period threshold and window. The format is T-W . T : set symbol period threshold. The scope is 1-65535, default:1 ; W : set symbol p… |
| 1.3.6.1.4.1.3902.15.2.11.22.5.1.7 | ColumnifLinkFrameThresholdWindow | read-write | current | Config link monitor frame threshold and window . The format is T-W . T : set frame threshold.The scope is 1-65535, default:1 ; W : set frame window. The scope … |
| 1.3.6.1.4.1.3902.15.2.11.22.5.1.8 | ColumnifLinkFramePeriodThresholdWindow | read-write | current | Config link monitor frame-period threshold and window . The format is T-W . T : set frame period threshold. The scope is 1-65535, default:1 ; W : set frame per… |
| 1.3.6.1.4.1.3902.15.2.11.22.5.1.9 | ColumnifLinkFrameSecondsThresholdWindow | read-write | current | Config link monitor frame-seconds threshold and window . The format is T-W . T : set frame seconds threshold. The scope is 1-900, default:1(s) ; W : set frame … |
| 1.3.6.1.4.1.3902.15.2.11.22.6 | TableethernetOamShowTable | not-accessible | current | Show ethernet oam configuration information |
| 1.3.6.1.4.1.3902.15.2.11.22.6.1 | RowethernetOamShowEntry | not-accessible | current | |
| 1.3.6.1.4.1.3902.15.2.11.22.6.1.2 | ColumnethernetOamShowDiscovery | read-only | current | Show ethernet oam discovery information. |
| 1.3.6.1.4.1.3902.15.2.11.22.6.1.3 | ColumnethernetOamShowLinkMonitor | read-only | current | Show ethernet oam statistics information. |
| 1.3.6.1.4.1.3902.15.2.11.22.6.1.4 | ColumnethernetOamShowStatistics | read-only | current | Show ethernet oam link monitor information. |
| 1.3.6.1.4.1.3902.15.2.11.22.7 | NotificationlinkMonitorSymbolPeriodTrap | current | The trap indicates nms that link monitor symbol period status. | |
| 1.3.6.1.4.1.3902.15.2.11.22.8 | NotificationlinkMonitorFrameTrap | current | The trap indicates nms that link monitor frame status. | |
| 1.3.6.1.4.1.3902.15.2.11.22.9 | NotificationlinkMonitorFramePeriodTrap | current | The trap indicates nms that link monitor frame period status. | |
| 1.3.6.1.4.1.3902.15.2.11.22.10 | NotificationlinkMonitorFrameSecondsTrap | current | The trap indicates nms that link monitor frame seconds status. | |
| 1.3.6.1.4.1.3902.15.2.11.22.11 | NotificationremoteLinkFailTrap | current | The trap indicates nms that remote link Fail. | |
| 1.3.6.1.4.1.3902.15.2.11.22.12 | NotificationremoteLinkOKTrap | current | The trap indicates nms that remote link OK. | |
| 1.3.6.1.4.1.3902.15.2.11.22.13 | NotificationdyingGaspTrap | current | The trap indicates nms that dying gasp status. | |
| 1.3.6.1.4.1.3902.15.2.11.22.14 | NotificationremoteDiscoveryFailTrap | current | The trap indicates nms that remote discovery Fail. | |
| 1.3.6.1.4.1.3902.15.2.11.22.15 | ScalarremoteMAC | not-accessible | current | Store remote MAC. |
| 1.3.6.1.4.1.3902.15.2.11.23 | NodeopticalInformation | |||
| 1.3.6.1.4.1.3902.15.2.11.23.1 | TableopticalInfoTable | not-accessible | current | Ethnet configuration table |
| 1.3.6.1.4.1.3902.15.2.11.23.1.1 | RowopticalInfoEntry | not-accessible | current | |
| 1.3.6.1.4.1.3902.15.2.11.23.1.1.1 | ColumnopticalInfoPortId | read-only | current | The port id |
| 1.3.6.1.4.1.3902.15.2.11.23.1.1.2 | ColumnopticalInfoIfName | read-only | current | Physical Ethnet interface ifName |
| 1.3.6.1.4.1.3902.15.2.11.23.1.1.3 | ColumnopticalInfoOnline | read-only | current | Optical Module Info Online |
| 1.3.6.1.4.1.3902.15.2.11.23.1.1.11 | ColumnopticalInfoSWaveLenth | read-only | current | Optical Module Info S_waveLenth(nm) |
| 1.3.6.1.4.1.3902.15.2.11.23.1.1.12 | ColumnopticalInfoPowerSupport | read-only | current | Optical Module Info power_supported |
| 1.3.6.1.4.1.3902.15.2.11.23.1.1.13 | ColumnopticalInfoSRxPower | read-only | current | Optical Module Info S_rxPower(mW) |
| 1.3.6.1.4.1.3902.15.2.11.23.1.1.14 | ColumnopticalInfoSRxPowerValid | read-only | current | Optical Module Info S_rxPowerValid |
| 1.3.6.1.4.1.3902.15.2.11.23.1.1.15 | ColumnopticalInfoSTxPower | read-only | current | Optical Module Info S_txPower(mW) |
| 1.3.6.1.4.1.3902.15.2.11.23.1.1.16 | ColumnopticalInfoSTxPowerValid | read-only | current | Optical Module Info S_txPowerValid |
| 1.3.6.1.4.1.3902.15.2.11.23.1.1.17 | ColumnopticalInfoSTxPowerStatus | read-only | current | Optical Module Info S_txPowerStatus |
| 1.3.6.1.4.1.3902.15.2.11.23.1.1.18 | ColumnopticalInfoSRxPowerStatus | read-only | current | Optical Module Info S_rxPowerStatus |
| 1.3.6.1.4.1.3902.15.2.11.23.1.1.23 | ColumnopticalInfoVName | read-only | current | Optical Module Info VName |
| 1.3.6.1.4.1.3902.15.2.11.23.1.1.24 | ColumnopticalInfoType | read-only | current | Optical Module Info type |
| 1.3.6.1.4.1.3902.15.2.11.23.1.1.26 | ColumnopticalInfoVSn | read-only | current | Optical Module Info VSn |
| 1.3.6.1.4.1.3902.15.2.11.23.1.1.27 | ColumnopticalInfoDistanse | read-only | current | Optical Module Info Distance(m) |
| 1.3.6.1.4.1.3902.15.2.11.23.1.1.28 | ColumnopticalInfoMode | read-only | current | The mode of the optical fiber. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| DisplayString | OCTET STRING | ||
| MacAddress | OCTET STRING DisplayString ::= OCTET STRING | current | Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M… |
| PortList | OCTET STRING | current | Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents… |