FRI-OPT-MIB
321 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | Counter enterprises |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.449 | Nodecodex | |||
| 1.3.6.1.4.1.449.2 | NodecdxProductSpecific | |||
| 1.3.6.1.4.1.449.2.1 | Nodecdx6500 | |||
| 1.3.6.1.4.1.449.2.1.2 | Nodecdx6500Configuration | |||
| 1.3.6.1.4.1.449.2.1.2.1 | Nodecdx6500CfgProtocolGroup | |||
| 1.3.6.1.4.1.449.2.1.2.1.1 | Nodecdx6500PCTPortProtocolGroup | |||
| 1.3.6.1.4.1.449.2.1.2.1.1.31 | Tablecdx6500PPCTFRIPortTable | not-accessible | mandatory | This table contains Frame Relay DTE Port configuration parameters. |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1 | Rowcdx6500PPCTFRIPortEntry | not-accessible | mandatory | Entries in the FRI Port Configuration Table. |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.1 | ColumnfriPCfgPortNumber | read-only | mandatory | Port number of this port. |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.2 | ColumnfriPCfgPortType | read-only | mandatory | Port type of the Port. |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.3 | ColumnfriPCfgConnectionType | read-write | mandatory | The Specified control signal handshake and clocking required for a connection to be made to this port : simp - simple, no control signals required. dtr - dedic… |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.4 | ColumnfriPCfgClockSource | read-write | mandatory | int - Internal clock source ext - External clock source. extint - Internal receive and external transmit clock source (DCE only). extlp - external receive and … |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.5 | ColumnfriPCfgClockSpeed | read-write | mandatory | This is the speed of the port in bits per second, when using internal clocking. The highest available speed is dependent on the card type, and on the interface… |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.6 | ColumnfriPCfgHighestStnNumber | read-only | deprecated | This is the highest station number that can be configured on the FRI port. It is used to limit the configuration of stations. |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.7 | ColumnfriPCfgFrameSeqCounting | read-only | mandatory | Port uses normal or extended frame sequence numbering: normal - normal sequencing (modulo 8) extended - extended sequencing (modulo 128). nc - Skipped during c… |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.8 | ColumnfriPCfgPktSeqCounting | read-write | mandatory | Port uses normal or extended packet level sequence numbers normal - normal sequencing (modulo 8) extended - extended sequencing (modulo 128) nc - Skipped durin… |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.9 | ColumnfriPCfgCntrlProtocolSupport | read-write | mandatory | Whether ANSI T1.617 Annex D, CCITT Q.933 Annex A or LMI Support is enabled. annexD - Annex D is enabled. none - None is enabled. lmi - LMI is enabled. annexA -… |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.10 | ColumnfriPCfgHighPriorityStn | read-write | mandatory | This parameter specifies a station who's PVC status has priority over all other stations when FRI same port back up is enabled. When the network reports this D… |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.11 | ColumnfriPCfgMaxVoiceBWBitsPerSec | read-write | mandatory | This parameter limits the bandwidth, in bits per sec (including overhead), for voice traffic passing through this frame relay port. A zero value disables any v… |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.12 | ColumnfriPCfgSegSizeVoicePresent | read-write | mandatory | Data packets to be segmented into this maximum frame size when voice is active on this port. segSize32 - 32 byte segments segSize64 - 64 byte segments segSize1… |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.13 | ColumnfriPCfgSegSizeVoiceNotPresent | read-write | mandatory | Data packets to be segmented into this maximum frame size when voice is not active on this port. segSize32 - 32 byte segments segSize64 - 64 byte segments segS… |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.14 | ColumnfriPCfgT391Timer | read-write | mandatory | This parameter is the Link Integrity Verification Timer polling period. The FRI port sends status enquiry messages to network every T391/nT1 seconds. |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.15 | ColumnfriPCfgT392Timer | read-write | mandatory | This parameter is the polling Cycle Verification Timer period. The FRI port expects status enquiry messages every T392/nT2 seconds. This parameter must be set … |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.16 | ColumnfriPCfgN391PollCycle | read-write | mandatory | Full Status polling cycle. FRI port sends Full status enquiry messages to network every nN1 polls. |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.17 | ColumnfriPCfgN392ErrsDuringMonitoredEvents | read-write | mandatory | Error inactivity threshold. Number of errors during NN3 events that cause the station to be declared inactive. Should be less than or equal to nN3. |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.18 | ColumnfriPCfgN393MonitoredEvents | read-write | mandatory | Monitored events count for measuring nN3. nN2 errors during nN3 events will cause the station to be declared inactive. Should be greater than nN3. |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.19 | ColumnfriPCfgNT1PollTimer | read-only | mandatory | This parameter is the Link Integrity Verification Timer polling period. The FRI port sends status enquiry messages to network every T391/nT1 seconds. |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.20 | ColumnfriPCfgNT2VerificationTimer | read-only | mandatory | This parameter is the polling Cycle Verification Timer period. The FRI port expects status enquiry messages every T392/nT2 seconds. This parameter must be set … |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.21 | ColumnfriPCfgNN1StatusPollingCycle | read-only | mandatory | Full Status polling cycle. FRI port sends Full status enquiry messages to network every nN1 polls. |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.22 | ColumnfriPCfgNN2ErrsDuringMonitoredEvents | read-only | mandatory | Error inactivity threshold. Number of errors during NN3 events that cause the station to be declared inactive. Should be less than or equal to nN3. |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.23 | ColumnfriPCfgNN3MonitoredEvents | read-only | mandatory | Monitored events count for measuring nN3. nN2 errors during nN3 events will cause the station to be declared inactive. Should be greater than nN3. |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.24 | ColumnfriPCfgInvertTXClock | read-write | mandatory | This parameter specifies whether the phase of the transmit clock should be inverted. Note: This parameter is primarily for X.21 electrical interfaces. no - Don… |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.25 | ColumnfriPCfgControlProtocolOptions | read-write | mandatory | These options control the PVC management protocol none - No option selected async - The port will send/receive asynchronous A-bit if it is performing Network s… |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.26 | ColumnfriPCfgDiscardControlOptions | read-write | mandatory | This parameter controls the discard frame options none - No option selected debit - DE marked frames are discarded before non-DE frames |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.27 | ColumnfriPCfgStartSvcDlci | read-write | mandatory | The configured number is the lowest value DLCI the FRI port will allow for use of FR SVCs. A value of 0 means SVC procedures are not operating on this port and… |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.28 | ColumnfriPCfgSubscriberNumber | read-write | mandatory | All stations on this port use this value for their calling address information element. The valid format of this entry is: xx...xx000101 or xx...xx000103 Where… |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.29 | ColumnfriPCfgMaxFmif | read-write | mandatory | This is the value used for link layer core parameters information element negotiation of maximum frame mode information field (FRIF) size in bytes. The value a… |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.30 | ColumnfriPCfgT200 | read-write | mandatory | This is the value in tenths of seconds (1/10 s) of the maximum time the DTE will wait for an acknowledgment of a transmitted Information frame. The DTE will co… |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.31 | ColumnfriPCfgN200 | read-write | mandatory | This is the maximum number of times the DTE will retransmit in order to recover from a T200 timeout condition. If this count expires, the DTE will declare the … |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.32 | ColumnfriPCfgWindowK | read-write | mandatory | This is the maximum sending window size which is the maximum number (k) of sequentially numbered I frames that may be outstanding (unacknowledged) at any given… |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.33 | ColumnfriPCfgT203 | read-write | mandatory | The idle timer (T203) represents the maximum time in seconds allowed without frames being exchanged. If the link remains idle for this period of time, the DTE … |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.34 | ColumnfriPCfgT303 | read-write | mandatory | The Setup Timer (T303) represents the maximum time in seconds allowed without a response to a SETUP message being received. Upon expiry, the SETUP message is r… |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.35 | ColumnfriPCfgT305 | read-write | mandatory | The Disconnect Timer (T305) represents the maximum time in seconds allowed without a response to a DISCONNECT message being received. Upon expiry, a RELEASE me… |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.36 | ColumnfriPCfgT308 | read-write | mandatory | The Release Timer (T308) represents the maximum time in seconds allowed without a response to a RELEASE message being received. Upon expiry, the RELEASE messag… |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.37 | ColumnfriPCfgT310 | read-write | mandatory | The Call Proceeding Timer (T310) value is in seconds. This timer is started when a CALL PROCEEDING response to a SETUP message is received. The timer is stoppe… |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.38 | ColumnfriPCfgControlProtocol | read-write | mandatory | This option controls whether the PVC management protocol acts like a DTE or a DCE DTE - This ports takes on the the DTE or User Side role DCE - This ports take… |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.39 | ColumnfriPCfguniState | read-write | mandatory | Enable FRF.12 UNI Segmentation. Peer must be enabled too. enable - Enable UNI Segmentation disable - Disable UNI Segmentation |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.40 | ColumnfriPCfguniSSVP | read-only | mandatory | UNI segment size when voice is present. Affects transmit path only. segSize64 - 64 byte segments segSize128 - 128 byte segments segSize256 - 256 byte segments … |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.41 | ColumnfriPCfguniSSVNP | read-write | mandatory | UNI segment size when voice is not present. Affects transmit path only. segSize64 - 64 byte segments segSize128 - 128 byte segments segSize256 - 256 byte segme… |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.42 | ColumnfriPCfguniSegDelay | read-write | mandatory | Discards a packet if any segment delays more than 10 seconds. Affects receive path only. enabled - discard the packet disabled - do not discard the packet |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.43 | ColumnfriPCfguniCheckPckSize | read-write | mandatory | Check if the packet size is larger than the node maximum packet size. enabled - discard packet than is larger than the maximum size. disabled - accept packet t… |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.44 | ColumnfriPCfgElectricalInterfaceType | read-write | mandatory | Specify the Electrical Interface Type: V.24 - V.24 Electrical Interface Type V.35 - V.35 Electrical Interface Type V.36 - V.36 Electrical Interface Type X.21 -… |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.45 | ColumnfriPCfgV24ElectricalInterfaceOption | read-write | mandatory | Specify the Pin 22 option: RI - V.24 uses Pin 22 for Ring Indicator output signal TM - V.24 uses Pin 22 for Test Mode input signal |
| 1.3.6.1.4.1.449.2.1.2.1.1.31.1.46 | ColumnfriPCfgHighSpeedElectricalInterfaceOption | read-write | mandatory | Specify the cable type: NONE - V.35/V.36/X.21 DCE with straight through cable XOVER - V.35/V.36/X.21 DCE with crossover adapter cable |
| 1.3.6.1.4.1.449.2.1.2.1.3 | Nodecdx6500PCTStationProtocolGroup | |||
| 1.3.6.1.4.1.449.2.1.2.1.3.9 | Tablecdx6500SPCTFRIStationTable | not-accessible | mandatory | This table contains Frame Relay DTE Station configuration parameters. |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1 | Rowcdx6500SPCTFRIStationEntry | not-accessible | mandatory | Entries in the FRI Station Configuration Table. |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.1 | ColumnfriSCfgPortNumber | read-only | mandatory | The FRI port number corresponding to this station. |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.2 | ColumnfriSCfgStnNumber | read-only | mandatory | The number of the configured FRI Station. |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.3 | ColumnfriSCfgStnType | read-write | mandatory | Identifies the type of station configured. annexG - This station uses X.25 signaling for layer 3. bypass - This station type bypasses layer 3. There is no sign… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.4 | ColumnfriSCfgDLCI | read-write | mandatory | The Data Link Connection Identifier (DLCI) is the unique identifier for the station on the FRI Port. Its valid range is 0, 16 - 1007. A zero value in this fiel… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.5 | ColumnfriSCfgCommInfoRate | read-write | mandatory | This parameter (CIR) specifies the rate (in bits-per-second) that the Frame Relay network agrees to transfer information under congested conditions for the FRI… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.6 | ColumnfriSCfgCommBurstSize | read-write | mandatory | This parameter (BC) specifies the maximum amount of data (in bits) that the Frame Relay network agrees to transfer over a time interval T = Committed Burst Siz… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.7 | ColumnfriSCfgTransDelay | read-write | mandatory | This parameter is the expected one-way delay through the network. This is specified in milliseconds. |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.8 | ColumnfriSCfgCongControlMode | read-write | mandatory | This parameter controls the method of congestion control: normal - congestion control is normal disable - never enter Congested State (CTRL) congested - never … |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.9 | ColumnfriSCfgLinkAddress | read-write | mandatory | The logical link address must be set to complementary values in this FRI Station and its corresponding remote FRI station: dte - station to have logical DTE ad… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.10 | ColumnfriSCfgPVCChannels | read-write | mandatory | Number of logical channels used for Permanent Virtual Circuits. The total number of PVC and SVC channels on a station (logical link) should be kept as small as… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.11 | ColumnfriSCfgStartingPVC | read-write | mandatory | This is the starting logical channel number for the Permanent Virtual Circuits on this FRI station. Not used if the number of PVCs = 0. |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.12 | ColumnfriSCfgSVCChannels | read-write | mandatory | Number of logical channels used in Switched Virtual Circuits. The total number of PVC and SVC channels on a station (logical link) should be kept as small as p… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.13 | ColumnfriSCfgStartingSVC | read-write | mandatory | This is the starting logical channel number for the switched Virtual Circuits on this station (logical link). Not used if the number of SVCs = 0. |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.14 | ColumnfriSCfgVoiceSVCChannels | read-write | mandatory | Number of logical voice channels used in Switched Virtual Circuits.The total number of voice and data channels on a station (logical link) should be kept as sm… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.15 | ColumnfriSCfgInitialFrame | read-write | mandatory | Specify the initial frame required by other end for (logical) link startup: none - do nothing (other end initiates link-up) sabm - send SABM disc - send DISC, … |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.16 | ColumnfriSCfgT1RetryTimer | read-write | mandatory | T1 link retry timer value in tenths of a second (e.g. 30 = 3.0 seconds). |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.17 | ColumnfriSCfgT4PollTimer | read-write | mandatory | This sets the time an idle link is probed for assurance of connection to the remote FRI station. 0 - disable the timer X - X is in tenths of a second (e.g. 40 … |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.18 | ColumnfriSCfgN2TransmissionTries | read-write | mandatory | The maximum number of attempts allowed to complete a transmission. |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.19 | ColumnfriSCfgKFrameWindow | read-write | mandatory | Frame level window size must be set to the same value at both this FRI station and the remote FRI station. |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.20 | ColumnfriSCfgWPacketWindow | read-write | mandatory | Packet level window size must be set to the same value at both this FRI station and the remote FRI station. |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.21 | ColumnfriSCfgPPacketSize | read-write | mandatory | This is the maximum X.25 packet size used on the station (logical link).For proper operation, this must be set to the same value at both this FRI station and t… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.22 | ColumnfriSCfgDataQUpperThreshold | read-write | mandatory | This is the maximum number of data packets a channel on this station (logical link) will queue for transmission before invoking flow control to the attached ch… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.23 | ColumnfriSCfgDataQLowerThreshold | read-write | mandatory | This is the number of data packets a channel on this FRI station will have queued for transmission when it releases flow control to the attached channel |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.24 | ColumnfriSCfgRestartTimer | read-write | mandatory | Restart-Request timeout timer in seconds. If timer expires on this FRI station, the Restart request is sent again. |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.25 | ColumnfriSCfgResetTimer | read-write | mandatory | Reset-Request timeout timer in seconds. If timer expires on this FRI station, the Reset request is sent again. |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.26 | ColumnfriSCfgCallTimer | read-write | mandatory | Call-Request timeout timer in seconds. If timer expires on this FRI station, the call is cleared. |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.27 | ColumnfriSCfgClearTimer | read-write | mandatory | Clear-Request timeout timer in seconds. If timer expires on this FRI station, the Clear request is sent again. |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.28 | ColumnfriSCfgX25Options | read-write | mandatory | Select X.25 options on this station (logical link) as follows: NONE - no option specified CUG - check closed user group; otherwise, CUG passes transparently CA… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.29 | ColumnfriSCfgRestrictedConnDest | read-write | mandatory | All calls entering this station will be routed to the destination specified in this parameter,irrespective of route selection table entries. For example, to ro… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.30 | ColumnfriSCfgCUGMembership | read-write | mandatory | The station may be a member of up to 8 different Closed User Groups (CUGs).Each CUG membership must be a two digit number (except 03). 00-99 - CUG Membership |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.31 | ColumnfriSCfgBillingRecords | read-write | mandatory | This controls whether billing (accounting) records will be created for calls on this FRI station. off - Billing records will not be created. on - Billing recor… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.32 | ColumnfriSCfgFrameSegmenter | read-write | mandatory | Determine if this station will support the Frame Segmenter Header.The Frame Segmenter should be enabled if the frame relay port is configured to pass voice tra… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.33 | ColumnfriSCfgVoiceCongCtrlMode | read-write | mandatory | This parameter controls the method of voice congestion control: enabled - Station is forced into congestion when voice calls are detected. disabled - Station o… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.34 | ColumnfriSCfgPeakUtilization | read-write | mandatory | The monitoring interval size specifies the time period to use when monitoring peak data link/CIR (Committed Information Rate) utilization. 0 - Disables this mo… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.35 | ColumnfriSCfgMaxInboundQueue | read-write | mandatory | This specifies the maximum number of frames from the network which may be queued in a BYPASS station. A smaller value may ve choosen for applications which exp… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.36 | ColumnfriSCfgAnnexGRateReduction | read-write | mandatory | This parameter determines whether Annex G stations will invoke implicit congestion control when a link error is detected, reducing their transmitted informatio… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.37 | ColumnfriSCfgCctType | read-write | mandatory | Select the station circuit type defined for the Frame Relay line. pvc - station will operate on its assigned DLCI as a PVC. svc - station will operate on a sel… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.38 | ColumnfriSCfgCallControl | read-write | mandatory | This parameter is used to control the calling behavior of the SVC station. auto - the station will automatically initiate a FR SVC call on power up autd - the … |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.39 | ColumnfriSCfgRetryInterval | read-write | mandatory | This is the time interval between call attempts, in seconds, that a station configured to initiate an SVC call will use. If a call attempt fails, either becaus… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.40 | ColumnfriSCfgCallAttempts | read-write | mandatory | This is the number of contiguous call attempts that a station configured to initiate an SVC call will make to establish the call. If this count expires, the st… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.41 | ColumnfriSCfgIdleInterval | read-write | mandatory | This is the idle time, in seconds, allowed for FRI station to remain idle. If the station using the SVC passes no data for this time period, the SVC will be cl… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.42 | ColumnfriSCfgIeNegotiation | read-write | mandatory | This allows the listing of parameters to be used in a SETUP/CONNECT message. dlci - If the station initiates a call, it will select the lowest value of DLCI av… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.43 | ColumnfriSCfgSubaddress | read-write | mandatory | This specifies the station subaddress coded and an IE. it is coded as an IA5 string with type of subaddress NSAP and IA5 AFI prefix added. Incoming calls with … |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.44 | ColumnfriSCfgCalledNumber | read-write | mandatory | This is the address of the destination, in the appropriate numbering plan, to which a call will be placed by this station. Called Party Number is a manditory I… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.45 | ColumnfriSCfgCalledSubaddress | read-write | mandatory | For outgoing calls, this specifies the calling subaddress IE coded as an IA5 string with type of subaddress NSAP and IA5 AFI prefix added. Incoming calls with … |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.46 | ColumnfriSCfgMinCir | read-write | mandatory | This parameter specifies the minimum rate (in bits-per-second) that the Frame Relay network agrees to transfer information under congested conditions for the F… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.47 | ColumnfriSCfgBurstExcess | read-write | mandatory | This parameter is negotiated during the call establishment phase of Frame Relay SVC calls. It has no effect on data transfer after the call has been establishe… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.48 | ColumnfriSCfgE2EEnabled | read-write | mandatory | Enable End-to-End Segmentation. Peer must be enabled too. enabled - Enable End-to-End Segmentation disabled - Disable End-to-End Segmentation |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.49 | ColumnfriSCfgE2EType | read-write | mandatory | Type of End-to-End Segmentation. Peer must be configured in the same way. FRF12 - FRF.12 End-to-End Segmentation Motorola - Motorola End-to-End Segmentation |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.50 | ColumnfriSCfgE2ESSVP | read-only | mandatory | Segment size when voice is present. Affects transmit path only. segSize64 - 64 byte segments segSize128 - 128 byte segments segSize256 - 256 byte segments segS… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.51 | ColumnfriSCfgE2ESSVNP | read-write | mandatory | Segment size when voice is not present. Affects transmit path only. segSize64 - 64 byte segments segSize128 - 128 byte segments segSize256 - 256 byte segments … |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.52 | ColumnfriSCfgE2ESegDelayEnabled | read-write | mandatory | Discards a packet if any segment delays more than 10 seconds. Affects receive path only. enabled - discard the packet disabled - do not discard the packet |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.53 | ColumnfriSCfgE2ECheckPckSize | read-write | mandatory | Check if the packet size is larger than the node maximum packet size. enabled - discard packet than is larger than the maximum size. disabled - accept packet t… |
| 1.3.6.1.4.1.449.2.1.2.1.3.9.1.54 | ColumnfriSCfgvoice-header | read-write | mandatory | Voice Header. enabled - Enable Voice Header Insertion disabled - Disable Voice Header Insertion |
| 1.3.6.1.4.1.449.2.1.3 | Nodecdx6500Statistics | |||
| 1.3.6.1.4.1.449.2.1.3.1 | Nodecdx6500StatProtocolGroup | |||
| 1.3.6.1.4.1.449.2.1.3.1.1 | Nodecdx6500PSTPortProtocolGroup | |||
| 1.3.6.1.4.1.449.2.1.3.1.1.32 | Nodecdx6500PPSTFRIPStatsTable | |||
| 1.3.6.1.4.1.449.2.1.3.1.1.32.1 | Tablecdx6500PPSTFRIPortTable | not-accessible | mandatory | This table contains FRI Port Statistics parameters. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.1.1 | Rowcdx6500PPSTFRIPortEntry | not-accessible | mandatory | Entries in the FRI Port Statistics Table. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.1.1.1 | ColumnfriPStatsPortNumber | read-only | mandatory | The port number of the FRI port. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.1.1.2 | ColumnfriPStatsPortType | read-only | mandatory | Port type of this port. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.1.1.3 | ColumnfriPStatsPortStatus | read-only | mandatory | Specifies the current port status. enabled - Port is operational. disabled - Port has been disabled. busyOut - Port has been busied out. up - Port is up and op… |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.1.1.4 | ColumnfriPStatsConfiguredStns | read-only | mandatory | A list of all the configured stations. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.1.1.5 | ColumnfriPStatsPortSpeed | read-only | mandatory | Message transmission speed in bits per second. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.1.1.6 | ColumnfriPStatsOpCntrlProtocol | read-only | mandatory | Control Protocol type learned from network. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.1.1.7 | ColumnfriPStatsSPBackup | read-only | mandatory | This indicates whether the same port backup is configured for this port. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.1.1.8 | ColumnfriPStatsPriorityStn | read-only | mandatory | This specifies the high priority station. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.1.1.9 | ColumnfriPStatsLastStatsReset | read-only | mandatory | This indicates the time stamp of the last statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.2 | Tablecdx6500PPSTFRIDataSummaryTable | not-accessible | mandatory | This table contains FRI Port Data Summary Statistics parameters. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.2.1 | Rowcdx6500PPSTFRIDataSummaryEntry | not-accessible | mandatory | Entries in the FRI Port Data Summary Statistics Table. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.2.1.1 | ColumnfriDataSummPortNumber | read-only | mandatory | The port number of the FRI port. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.2.1.2 | ColumnfriPStatsCharInTotal | read-only | mandatory | Number of characters received since last boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.2.1.3 | ColumnfriPStatsCharOutTotal | read-only | mandatory | Number of characters transmitted since last boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.2.1.4 | ColumnfriPStatsCharInPerSec | read-only | mandatory | Average number of characters received per second. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.2.1.5 | ColumnfriPStatsCharOutPerSec | read-only | mandatory | Average number of characters transmitted per second. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.2.1.6 | ColumnfriPStatsFramesInTotal | read-only | mandatory | Number of frames received since last boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.2.1.7 | ColumnfriPStatsFramesOutTotal | read-only | mandatory | Number of frames transmitted since last boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.2.1.8 | ColumnfriPStatsFramesInPerSec | read-only | mandatory | Average number of frames received per second. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.2.1.9 | ColumnfriPStatsFramesOutPerSec | read-only | mandatory | Average number of frames transmitted per second. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.2.1.10 | ColumnfriPStatsAvFrameSizeIn | read-only | mandatory | Average frame size of received frames. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.2.1.11 | ColumnfriPStatsAvFrameSizeOut | read-only | mandatory | Average size of transmitted frames. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.2.1.12 | ColumnfriPStatsUtilIn | read-only | mandatory | Port Utilization of incoming data. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.2.1.13 | ColumnfriPStatsUtilOut | read-only | mandatory | Port Utilization of outgoing data. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.3 | Tablecdx6500PPSTFRISummaryTable | not-accessible | mandatory | This table contains FRI Summary Statistics parameters. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.3.1 | Rowcdx6500PPSTFRISummaryEntry | not-accessible | mandatory | Entries in the FRI Summary Statistics Table. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.3.1.1 | ColumnfriSummPortNumber | read-only | mandatory | The port number of the FRI port. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.3.1.2 | ColumnfriPStatsCRCErrors | read-only | mandatory | Number of errors detected by Cyclic Redundancy Check since last node boot or reset of statistics. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.3.1.3 | ColumnfriPStatsOverrunErrors | read-only | mandatory | Number of OverrunErrors detected since last node boot or reset of statistics. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.3.1.4 | ColumnfriPStatsFrameLengthErrors | read-only | mandatory | Number of Frame Length Errors detected since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.3.1.5 | ColumnfriPStatsUnderrunErrors | read-only | mandatory | Number of Underrun Errors detected since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.3.1.6 | ColumnfriPStatsUnknownDLCICount | read-only | mandatory | This specifies the number of DLCIs not recognized. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.3.1.7 | ColumnfriPStatsLastUnknownDLCI | read-only | mandatory | This specifies the last unknown dlci received. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.3.1.8 | ColumnfriPStatsSplittingRatio | read-only | mandatory | The Frame Segmenter's splitting ratio calculated as a percentage of Number of frames segmented/Number of frames. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.3.1.9 | ColumnfriPStatsTotalSegmentsLost | read-only | mandatory | Total Segments lost by Frame Segmenter Receiver. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.3.1.10 | ColumnfriPStatsMaxContiguousSegmentsLost | read-only | mandatory | Maximum consecutive segments lost by Farme Segmenter Receiver. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.3.1.11 | ColumnfriPStatsVoiceBWOnPort | read-only | mandatory | Current amount of voice bandwidth allocated. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.3.1.12 | ColumnfriPStatsFrameSegmenterSyncLost | read-only | mandatory | Total number of times synchronization has been lost. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.3.1.13 | ColumnfriPStatsStatusEnqSentFull | read-only | mandatory | Number of status enquiries SENT FULL. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.3.1.14 | ColumnfriPStatsFullStatusRecd | read-only | mandatory | Number of full status received. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.3.1.15 | ColumnfriPStatsStatusEnqSentLIV | read-only | mandatory | Number of status enq sent LIV. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.3.1.16 | ColumnfriPStatsLIVStatusRecd | read-only | mandatory | Number of status update received. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.3.1.17 | ColumnfriPStatsStatusEnqRecdFull | read-only | mandatory | Number of Full status enq RCV bi-directional mode. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.3.1.18 | ColumnfriPStatsStatusEnqRecdLIV | read-only | mandatory | Number of LIV status enq RCV bi-directional mode. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.3.1.19 | ColumnfriPStatsAsyncUpdateRecd | read-only | mandatory | Number of async update received. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.3.1.20 | ColumnfriPStatsSeqNumMismatch | read-only | mandatory | Number of Sequence Number Mismatches occurred. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.3.1.21 | ColumnfriPStatsTimeouts | read-only | mandatory | Number of timeouts occurred. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.4 | Tablecdx6500PPSTFRIISDNCallStatusTable | not-accessible | mandatory | This table contains FRI ISDN Statistics parameters. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.4.1 | Rowcdx6500PPSTFRIISDNCallStatusEntry | not-accessible | mandatory | Entries in the FRI ISDN Statistics Table. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.4.1.1 | ColumnfriISDNCallStatusPortNumber | read-only | mandatory | The port number of the FRI Port. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.4.1.2 | ColumnfriPStatsNumRxCallsSinceLastReset | read-only | mandatory | The number of inbound calls that were attempted since the last statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.4.1.3 | ColumnfriPStatsNumRxCallsRejected | read-only | mandatory | The number of inbound calls that were rejected since the last statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.4.1.4 | ColumnfriPStatsRxLastCallFailureCause | read-only | mandatory | The reason the last inbound call was rejected, since the last statistics reset. The posssible values are: noFailureReported - No call failure noAvailableVirtua… |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.4.1.5 | ColumnfriPStatsRxLastCalledNumber | read-only | mandatory | The phone number of the virtual port of the last ISDN call made into this port. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.4.1.6 | ColumnfriPStatsRxLastCallingNumber | read-only | mandatory | The phone number of last party to make an ISDN call into this port. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.4.1.7 | ColumnfriPStatsRxMinCallDuration | read-only | mandatory | The minimum call duration of all inbound ISDN calls made into this port, since the last statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.4.1.8 | ColumnfriPStatsRxMaxCallDuration | read-only | mandatory | The maximum call duration of all inbound ISDN calls made into this port, since the last statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.4.1.9 | ColumnfriPStatsRxAvgCallDuration | read-only | mandatory | The average call duration of all inbound ISDN calls made into this port, since the last statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.4.1.10 | ColumnfriPStatsNumTxCallsSinceLastReset | read-only | mandatory | The number of outbound calls that were attempted since the last statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.4.1.11 | ColumnfriPStatsNumTxCallsRejected | read-only | mandatory | The number of outbound calls that were rejected since the last statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.4.1.12 | ColumnfriPStatsTxLastCallFailureCause | read-only | mandatory | The reason the last outbound call was rejected, since the last statistics reset. The posssible values are: noFailureReported - No call failure noAvailableVirtu… |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.4.1.13 | ColumnfriPStatsTxLastCalledNumber | read-only | mandatory | The phone number of the last ISDN call made by a virtual port from this port. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.4.1.14 | ColumnfriPStatsTxLastCallingNumber | read-only | mandatory | The phone number of the virtual port that made the last ISDN call from this port. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.4.1.15 | ColumnfriPStatsTxMinCallDuration | read-only | mandatory | The minimum call duration of all outbound ISDN calls made from this port, since the last statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.4.1.16 | ColumnfriPStatsTxMaxCallDuration | read-only | mandatory | The maximum call duration of all outbound ISDN calls made from this port, since the last statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.4.1.17 | ColumnfriPStatsTxAvgCallDuration | read-only | mandatory | The average call duration of all outbound ISDN calls made from this port, since the last statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.32.4.1.18 | ColumnfriPStatsSignalingState | read-only | mandatory | ISDN call signaling state. The possible values are: idle - No ISDN call present. ringing - Pending outgoing ISDN call request. connected - ISDN call is connect… |
| 1.3.6.1.4.1.449.2.1.3.1.3 | Nodecdx6500PSTStationProtocolGroup | |||
| 1.3.6.1.4.1.449.2.1.3.1.3.10 | Nodecdx6500SPSTFRISStatsTable | |||
| 1.3.6.1.4.1.449.2.1.3.1.3.10.1 | TablefriSGenStatsTable | not-accessible | mandatory | This table contains FRI Station Statistics parameters. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.1.1 | Rowcdx6500friSGenStatsEntry | not-accessible | mandatory | Entries in the FRI Station Statistics Table. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.1.1.1 | ColumnfriSGenStatsPortNumber | read-only | mandatory | The FRI port number corresponding to this station. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.1.1.2 | ColumnfriSGenStatsStnNumber | read-only | mandatory | The number of the FRI Station. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.1.1.3 | ColumnfriSStatsStnType | read-only | mandatory | annex G - Annex G station type. bypass - bypass station type. voice - voice station type. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.1.1.4 | ColumnfriSStatsStnStatus | read-only | mandatory | Status of the station. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.1.1.5 | ColumnfriSStatsDLCI | read-only | mandatory | Data Link Connection Identifier is the unique identifier for the station on the FRI port and must match the DLCI configured on the Frame Relay networking node.… |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.1.1.6 | ColumnfriSStatsStnState | read-only | mandatory | Specifies the state of the station : unused - station is unconfigured/disabled uncontrolled - station is not controlled. controlled - station is controlled, co… |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.1.1.7 | ColumnfriSStatsConfiguredCIR | read-only | mandatory | Committed Information Rate in bits per second : Value of this parameter is 0 for Bypass stations (not available). |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.1.1.8 | ColumnfriSStatsAllowedInfoRate | read-only | mandatory | Allowed information rate is the link speed if uncongested, 0 if unused and the current desired information rate if congested. Value of this parameter is also 0… |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.1.1.9 | ColumnfriSStatsImpCongDetect | read-only | mandatory | Number of times implicit congestion procedures have been invoked.Value of this parameter is 0 for Bypass stations (not available). |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.1.1.10 | ColumnfriSStatsExpCongDetect | read-only | mandatory | Number of times explicit congestion procedures have been invoked. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.1.1.11 | ColumnfriSStatsLMIFlowCntrl | read-only | mandatory | This indicates the flow status, whether OFF or ON. na - Value not available. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.1.1.12 | ColumnfriSStatsMaxSVCCount | read-only | mandatory | Maximum number of SVCs available in the network. Value of this parameter is 0 for Bypass stations (not available) |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.1.1.13 | ColumnfriSStatsCurrSVCCount | read-only | mandatory | Number of SVCs currently in use. Value of this parameter is 0 for Bypass stations (not available) |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.1.1.14 | ColumnfriSStatsMaxPVCCount | read-only | mandatory | Maximum number of async pvc channels. Value of this parameter is 0 for Bypass stations (not available) |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.1.1.15 | ColumnfriSStatsCurrPVCCount | read-only | mandatory | Current number of async pvc channels. Value of this parameter is 0 for Bypass stations (not available) |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.1.1.16 | ColumnfriSStatsLastStatsReset | read-only | mandatory | This indicates the time stamp of the last statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.1.1.17 | ColumnfriSStatsFrameSegState | read-only | mandatory | State of the Frame segmenter receiver. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.1.1.18 | ColumnfriSStatsFrameSegSyncLost | read-only | mandatory | Total number of segments lost by Frame Segmenter Receiver. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.1.1.19 | ColumnfriSStatsPVCState | read-only | mandatory | Current state of the PVC. Value of this parameter is not available for stations other than Bypass Stations. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.1.1.20 | ColumnfriSStatsVoiceCongDetect | read-only | mandatory | Number of times voice congestion procedures have been invoked. Value of this parameter is 0 (Not Available) for Bypass stations. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.1.1.21 | ColumnfriSStatsMaxVSVCCount | read-only | mandatory | Maximum number of Voice SVCs available in the network. Value of this parameter is 0 for Bypass stations (not available) |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.1.1.22 | ColumnfriSStatsCurrVSVCCount | read-only | mandatory | Number of Voice SVCs currently in use. Value of this parameter is 0 for Bypass stations (not available) |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.2 | TablefriSDataSummaryStatsTable | not-accessible | mandatory | This table contains FRI Station Data Summary Statistics parameters. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.2.1 | Rowcdx6500friSDataSummaryStatsEntry | not-accessible | mandatory | Entries in the FRI Station Data Summary Statistics Table. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.2.1.1 | ColumnfriSDataSummStatsPortNumber | read-only | mandatory | The FRI port number corresponding to this station. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.2.1.2 | ColumnfriSDataSummStatsStnNumber | read-only | mandatory | The number of the FRI station. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.2.1.3 | ColumnfriSStatsCharInTotal | read-only | mandatory | Number of characters received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.2.1.4 | ColumnfriSStatsCharOutTotal | read-only | mandatory | Number of characters transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.2.1.5 | ColumnfriSStatsCharInPerSec | read-only | mandatory | Average number of characters received per second. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.2.1.6 | ColumnfriSStatsCharOutPerSec | read-only | mandatory | Average number of characters transmitted per second. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.2.1.7 | ColumnfriSStatsPktInTotal | read-only | mandatory | Number of packets received since last node boot or statistics reset. Value of this parameter is 0 for Bypass stations (not available) |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.2.1.8 | ColumnfriSStatsPktOutTotal | read-only | mandatory | Number of packets transmitted since last node boot or statistics reset. Value of this parameter is 0 for Bypass stations (not available) |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.2.1.9 | ColumnfriSStatsPktInPerSec | read-only | mandatory | Average number of packets received per second. Value of this parameter is 0 for Bypass stations (not available) |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.2.1.10 | ColumnfriSStatsPktOutPerSec | read-only | mandatory | Average number of packets transmitted per second. Value of this parameter is 0 for Bypass stations (not available) |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.2.1.11 | ColumnfriSStatsFrameInTotal | read-only | mandatory | Number of frames transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.2.1.12 | ColumnfriSStatsFrameOutTotal | read-only | mandatory | Number of frames transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.2.1.13 | ColumnfriSStatsFrameInPerSec | read-only | mandatory | Average number of frames received per second. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.2.1.14 | ColumnfriSStatsFrameOutPerSec | read-only | mandatory | Average number of frames transmitted per second. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.2.1.15 | ColumnfriSStatsUtilIn | read-only | mandatory | Indicates the quantity of user bytes received on the link expressed as a percentage of the maximum number of bytes that could have been received. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.2.1.16 | ColumnfriSStatsUtilOut | read-only | mandatory | Indicates the quantity of user bytes sent down the link expressed as a percentage of the maximum number of bytes that could have been sent. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.2.1.17 | ColumnfriSStatsNumPktsQueued | read-only | mandatory | Current number of packets buffered since last node boot or statistics reset. Value of this parameter is 0 for Bypass stations (not available) |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.2.1.18 | ColumnfriSStatsPktsDiscardIn | read-only | mandatory | Number of incoming packets discarded. Value of this parameter is only available for Bypass stations, 0 is returned otherwise. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.2.1.19 | ColumnfriSStatsPktsDiscardOut | read-only | mandatory | Number of outgoing packets discarded. Value of this parameter is only available for Bypass stations, 0 is returned otherwise. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.2.1.20 | ColumnfriSStatsPktsQueuedIn | read-only | mandatory | Current number of Incoming packets buffered since last node boot or statistics reset of a Bypass station. Value of this parameter is only available for Bypass … |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.2.1.21 | ColumnfriSStatsPktsQueuedOut | read-only | mandatory | Current number of Outgoing packets buffered since last node boot or statistics reset of a Bypass station. Value of this parameter is only available for Bypass … |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.3 | TablefriSVoiceSummaryStatsTable | not-accessible | mandatory | This table contains FRI Station Voice Summary Statistics parameters. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.3.1 | Rowcdx6500friSVoiceSummaryStatsEntry | not-accessible | mandatory | Entries in the FRI Station Voice Summary Statistics Table. NOTE : Value of all objects in this table will be 0 for Bypass stations (not available). |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.3.1.1 | ColumnfriSVoiceSummStatsPortNumber | read-only | mandatory | The FRI port number corresponding to this station. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.3.1.2 | ColumnfriSVoiceSummStatsStnNumber | read-only | mandatory | The number of the FRI station. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.3.1.3 | ColumnfriSStatsVoiceCharInTotal | read-only | mandatory | Total number of voice characters received. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.3.1.4 | ColumnfriSStatsVoiceCharOutTotal | read-only | mandatory | Total number of voice characters transmitted. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.3.1.5 | ColumnfriSStatsVoiceCharInPerSec | read-only | mandatory | Number of voice characters received per second. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.3.1.6 | ColumnfriSStatsVoiceCharOutPerSec | read-only | mandatory | Number of voice characters transmitted per second. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.3.1.7 | ColumnfriSStatsVoicePktInTotal | read-only | mandatory | Total number of voice packets received. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.3.1.8 | ColumnfriSStatsVoicePktOutTotal | read-only | mandatory | Total number of voice packets transmitted. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.3.1.9 | ColumnfriSStatsVoicePktInPerSec | read-only | mandatory | Number of voice packets received per second. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.3.1.10 | ColumnfriSStatsVoicePktOutPerSec | read-only | mandatory | Number of voice packets transmitted per second. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.4 | TablefriSFrameSummaryStatsTable | not-accessible | mandatory | This table contains FRI Station Frame Summary Statistics parameters. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.4.1 | Rowcdx6500friSFrameSummaryStatsEntry | not-accessible | mandatory | Entries in the FRI Station Frame Summary Statistics Table. NOTE : Value of all objects in this table will be 0 for Bypass stations (not available) |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.4.1.1 | ColumnfriSFrameSummStatsPortNumber | read-only | mandatory | The FRI port number corresponding to this station. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.4.1.2 | ColumnfriSFrameSummStatsStnNumber | read-only | mandatory | The number of the FRI station. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.4.1.3 | ColumnfriSStatsInfoFramesInTotal | read-only | mandatory | Information Frames received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.4.1.4 | ColumnfriSStatsInfoFramesOutTotal | read-only | mandatory | Information Frames transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.4.1.5 | ColumnfriSStatsRRFramesInTotal | read-only | mandatory | Number of RR Frames received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.4.1.6 | ColumnfriSStatsRRFramesOutTotal | read-only | mandatory | Number of RR Frames transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.4.1.7 | ColumnfriSStatsRNRFramesInTotal | read-only | mandatory | Number of RNR frames received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.4.1.8 | ColumnfriSStatsRNRFramesOutTotal | read-only | mandatory | Number of RNR frames transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.4.1.9 | ColumnfriSStatsREJFramesInTotal | read-only | mandatory | Number of REJ frames received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.4.1.10 | ColumnfriSStatsREJFramesOutTotal | read-only | mandatory | Number of REJ frames transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.4.1.11 | ColumnfriSStatsSABMFramesInTotal | read-only | mandatory | Number of SABM frames received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.4.1.12 | ColumnfriSStatsSABMFramesOutTotal | read-only | mandatory | Number of SABM frames transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.4.1.13 | ColumnfriSStatsDISCFramesInTotal | read-only | mandatory | Number of DISC frames received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.4.1.14 | ColumnfriSStatsDISCFramesOutTotal | read-only | mandatory | Number of DISC frames transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.4.1.15 | ColumnfriSStatsDMFramesInTotal | read-only | mandatory | Number of DM frames received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.4.1.16 | ColumnfriSStatsDMFramesOutTotal | read-only | mandatory | Number of DM frames transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.4.1.17 | ColumnfriSStatsUAFramesInTotal | read-only | mandatory | Number of UA frames received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.4.1.18 | ColumnfriSStatsUAFramesOutTotal | read-only | mandatory | Number of UA frames transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.4.1.19 | ColumnfriSStatsFRMRFramesInTotal | read-only | mandatory | Number of FRMR frames received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.4.1.20 | ColumnfriSStatsFRMRFramesOutTotal | read-only | mandatory | Number of FRMR frames transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5 | TablefriSPacketSummaryStatsTable | not-accessible | mandatory | This table contains FRI Station Packet Summary Statistics parameters. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1 | Rowcdx6500friSPacketSummaryStatsEntry | not-accessible | mandatory | Entries in the FRI Station Packet Summary Statistics Table. NOTE : Value of all objects in this table will be 0 for Bypass stations (not available) |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.1 | ColumnfriSPktSummStatsPortNumber | read-only | mandatory | The FRI port number corresponding to this station. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.2 | ColumnfriSPktSummStatsStnNumber | read-only | mandatory | The number of the FRI station. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.3 | ColumnfriSStatsDataPktInTotal | read-only | mandatory | Number of Data packets received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.4 | ColumnfriSStatsDataPktOutTotal | read-only | mandatory | Number of Data packets transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.5 | ColumnfriSStatsRRPktInTotal | read-only | mandatory | Number of RR packets received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.6 | ColumnfriSStatsRRPktOutTotal | read-only | mandatory | Number of RR packets transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.7 | ColumnfriSStatsRNRPktInTotal | read-only | mandatory | Number of RNR packets received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.8 | ColumnfriSStatsRNRPktOutTotal | read-only | mandatory | Number of RNR packets transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.9 | ColumnfriSStatsREJPktInTotal | read-only | mandatory | Number of REJ packets received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.10 | ColumnfriSStatsREJPktOutTotal | read-only | mandatory | Number of REJ packets transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.11 | ColumnfriSStatsCallReqPktInTotal | read-only | mandatory | Number of call request packets received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.12 | ColumnfriSStatsCallReqPktOutTotal | read-only | mandatory | Number of call request packets transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.13 | ColumnfriSStatsCallAccPktInTotal | read-only | mandatory | Number of call accept packets received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.14 | ColumnfriSStatsCallAccPktOutTotal | read-only | mandatory | Number of call accept packets transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.15 | ColumnfriSStatsClrReqPktInTotal | read-only | mandatory | Number of clear request packets received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.16 | ColumnfriSStatsClrReqPktOutTotal | read-only | mandatory | Number of clear request packets transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.17 | ColumnfriSStatsClrConfPktInTotal | read-only | mandatory | Number of clear confirm packets received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.18 | ColumnfriSStatsClrConfPktOutTotal | read-only | mandatory | Number of clear confirm packets transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.19 | ColumnfriSStatsIntrReqPktInTotal | read-only | mandatory | Number of interrupt request packets received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.20 | ColumnfriSStatsIntrReqPktOutTotal | read-only | mandatory | Number of interrupt request packets transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.21 | ColumnfriSStatsIntrConfPktInTotal | read-only | mandatory | Number of interrupt confirm packets received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.22 | ColumnfriSStatsIntrConfPktOutTotal | read-only | mandatory | Number of interrupt confirm packets transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.23 | ColumnfriSStatsResetReqPktInTotal | read-only | mandatory | Number of reset request packets received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.24 | ColumnfriSStatsResetReqPktOutTotal | read-only | mandatory | Number of reset request packets transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.25 | ColumnfriSStatsResetConfPktInTotal | read-only | mandatory | Number of reset confirm packets received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.26 | ColumnfriSStatsResetConfPktOutTotal | read-only | mandatory | Number of reset confirm packets transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.27 | ColumnfriSStatsRestartReqPktInTotal | read-only | mandatory | Number of restart request packets received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.28 | ColumnfriSStatsRestartReqPktOutTotal | read-only | mandatory | Number of restart request packets transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.29 | ColumnfriSStatsRestartConfPktInTotal | read-only | mandatory | Number of restart confirm packets received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.5.1.30 | ColumnfriSStatsRestartConfPktOutTotal | read-only | mandatory | Number of restart confirm packets transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.6 | TablefriSFRISummaryStatsTable | not-accessible | mandatory | This table contains FRI Station FRI Summary Statistics parameters. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.6.1 | Rowcdx6500friSFRISummaryStatsEntry | not-accessible | mandatory | Entries in the FRI Station FRI Summary Statistics Table. NOTE : Value of all objects in this table are valid only for Bypass stations; 0 will be returned other… |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.6.1.1 | ColumnfriSFRISummStatsPortNumber | read-only | mandatory | The FRI port number corresponding to this station. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.6.1.2 | ColumnfriSFRISummStatsStnNumber | read-only | mandatory | The number of the FRI station. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.6.1.3 | ColumnfriSStatsFECNInTotal | read-only | mandatory | Number of Forward Explicit Congestion Notification (FECN) packets received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.6.1.4 | ColumnfriSStatsFECNOutTotal | read-only | mandatory | Number of Forward Explicit Congestion Notification (FECN) packets transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.6.1.5 | ColumnfriSStatsBECNInTotal | read-only | mandatory | Number of Backward Explicit Congestion Notification (BECN) packets received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.6.1.6 | ColumnfriSStatsBECNOutTotal | read-only | mandatory | Number of Backward Explicit Congestion Notification (BECN) packets transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.6.1.7 | ColumnfriSStatsDEInTotal | read-only | mandatory | Number of Discard Eligibility (DE) packets received since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.3.10.6.1.8 | ColumnfriSStatsDEOutTotal | read-only | mandatory | Number of Discard Eligibility (DE) packets transmitted since last node boot or statistics reset. |
| 1.3.6.1.4.1.449.2.1.4 | Nodecdx6500Controls | |||
| 1.3.6.1.4.1.449.2.1.4.14 | Nodecdx6500ContFRITable | |||
| 1.3.6.1.4.1.449.2.1.4.14.1 | Tablecdx6500FRIPContTable | not-accessible | mandatory | Control parameters for FRI ports. |
| 1.3.6.1.4.1.449.2.1.4.14.1.1 | Rowcdx6500FRIPContEntry | not-accessible | mandatory | Each control applies to a single FRI port. |
| 1.3.6.1.4.1.449.2.1.4.14.1.1.1 | ColumnfriPContPortNumber | not-accessible | mandatory | Port number of the FRI port. |
| 1.3.6.1.4.1.449.2.1.4.14.1.1.2 | ColumnfriPContPortControl | write-only | mandatory | Control operations for the specified FRI port. boot - Boots the FRI port enable - Enables the FRI port disable - Disables the FRI port resetstats - Resets the … |
| 1.3.6.1.4.1.449.2.1.4.14.2 | Tablecdx6500FRISContTable | not-accessible | mandatory | Control parameters for FRI stations. |
| 1.3.6.1.4.1.449.2.1.4.14.2.1 | Rowcdx6500FRISContEntry | not-accessible | mandatory | Each control applies to a single FRI station. |
| 1.3.6.1.4.1.449.2.1.4.14.2.1.1 | ColumnfriSContPortNumber | not-accessible | mandatory | The FRI port number corresponding to this station. |
| 1.3.6.1.4.1.449.2.1.4.14.2.1.2 | ColumnfriSContStnNumber | not-accessible | mandatory | FRI station number. |
| 1.3.6.1.4.1.449.2.1.4.14.2.1.3 | ColumnfriSContStnControl | write-only | mandatory | Control operations for the specified FRI station. boot - Boots the FRI station enable - Enables the FRI station disable - Disables the FRI station resetstats -… |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| DisplayString | OCTET STRING |