MIB Viewer

Fore-E3-MIB

50 objects
write something interesting here
Imported Objects
Fore-Common-MIBasx
SNMPv2-SMICounter32 Integer32 MODULE-IDENTITY OBJECT-TYPE
OIDNameAccessStatusDescription
1.3.6.1.4.1.326.2.2.1.1.5IdentityforeE3write something interesting here
1.3.6.1.4.1.326.2.2.1.1.5.1Nodee3ConfGroup
1.3.6.1.4.1.326.2.2.1.1.5.1.1Tablee3ConfTablenot-accessiblecurrentA table of E3 switch port configuration information.
1.3.6.1.4.1.326.2.2.1.1.5.1.1.1Rowe3ConfEntrynot-accessiblecurrentA table entry containing E3 configuration information for each port. Not all RFC1407 configuration table variables are included, and some are modified.
1.3.6.1.4.1.326.2.2.1.1.5.1.1.1.1Columne3ConfBoardread-onlycurrentThe index of this port's switch board.
1.3.6.1.4.1.326.2.2.1.1.5.1.1.1.2Columne3ConfModuleread-onlycurrentThe network module of this port.
1.3.6.1.4.1.326.2.2.1.1.5.1.1.1.3Columne3ConfPortread-onlycurrentThe number of this port.
1.3.6.1.4.1.326.2.2.1.1.5.1.1.1.4Columne3LineTyperead-writecurrentThis variable indicates the type of cell delineation being used. The e3Plcp(3) value indicates cell delineation according to CCITT G.751 using PLCP (Physical L…
1.3.6.1.4.1.326.2.2.1.1.5.1.1.1.5Columne3LineCodingread-onlycurrentThis variable describes the variety of Zero Code suppression used on this interface, which in turn affects a number of its characteristics. e3HDB3 (1) refers t…
1.3.6.1.4.1.326.2.2.1.1.5.1.1.1.6Columne3SendCoderead-onlycurrentThis variable indicates what type of code is being sent across the E3/E3 interface by the device. The values mean: e3SendNoCode sending looped or normal data e…
1.3.6.1.4.1.326.2.2.1.1.5.1.1.1.7Columne3ReceiveCoderead-onlycurrentThis variable indicates the type of code that was received across the E3/E3 interface. The values mean: e3ReceiveNoCode receiving looped or normal data e3Recei…
1.3.6.1.4.1.326.2.2.1.1.5.1.1.1.8Columne3LoopbackConfigread-writecurrentThis variable represents the loopback configuration of the E3 interface. This variable is defined in the rfc1407 configuration table as dsx3LoopbackConfig, wit…
1.3.6.1.4.1.326.2.2.1.1.5.1.1.1.9Columne3TxClockSourceread-writecurrentThe source of the transmit clock.
1.3.6.1.4.1.326.2.2.1.1.5.1.1.1.10Columne3RxScramblingread-writecurrentThis variable indicates whether the information is being descrambled on receiving. It should be set the same as the transmitting side.
1.3.6.1.4.1.326.2.2.1.1.5.1.1.1.11Columne3TxScramblingread-writecurrentThis variable indicates whether the information (48 octet payload) is being scrambled before transmitting. It should be set the same as the receiving side.
1.3.6.1.4.1.326.2.2.1.1.5.1.1.1.12Columne3LineStatusread-onlycurrentThis variable indicates the Line Status of the interface. A similar object is defined in the rfc1407 configuration table as dsx3LineStatus (the e3RxFERF bit is…
1.3.6.1.4.1.326.2.2.1.1.5.1.1.1.13Columne3IdleUnassignedCellsread-writecurrentThis variable indicates the types of cells that should be sent in case there is no real data to send. According to the ATM Forum, Unassigned cells should be se…
1.3.6.1.4.1.326.2.2.1.1.5.2Nodee3StatsGroup
1.3.6.1.4.1.326.2.2.1.1.5.2.1Tablee3FramingTablenot-accessiblecurrentA table of E3 framing statistics information.
1.3.6.1.4.1.326.2.2.1.1.5.2.1.1Rowe3FramingEntrynot-accessiblecurrentA table entry containing E3 framing statistics information.
1.3.6.1.4.1.326.2.2.1.1.5.2.1.1.1Columne3FramingBoardread-onlycurrentThe index of this port's switch board.
1.3.6.1.4.1.326.2.2.1.1.5.2.1.1.2Columne3FramingModuleread-onlycurrentThe network module of this port.
1.3.6.1.4.1.326.2.2.1.1.5.2.1.1.3Columne3FramingPortread-onlycurrentThe number of this port.
1.3.6.1.4.1.326.2.2.1.1.5.2.1.1.4Columne3FramingLOSsread-onlycurrentThe number of seconds in which Loss Of Signal (LOS) errors were detected by the E3 Receive Framer block.
1.3.6.1.4.1.326.2.2.1.1.5.2.1.1.5Columne3FramingLCVsread-onlycurrentThe number of Line Code Violations (LCV) that were detected by the E3 Receive Framer block.
1.3.6.1.4.1.326.2.2.1.1.5.2.1.1.6Columne3FramingFERRsread-onlycurrentNumber of E3 framing error (FERR) events.
1.3.6.1.4.1.326.2.2.1.1.5.2.1.1.7Columne3FramingOOFsread-onlycurrentNumber of seconds when E3 Out Of Frame (OOF) error events.
1.3.6.1.4.1.326.2.2.1.1.5.2.1.1.8Columne3FramingFERFsread-onlycurrentIn a G.832 (e3LineType == e3Framed) configured port, this variable relects the number of seconds when Far End Receive Failures were experienced. In G.751 (e3Li…
1.3.6.1.4.1.326.2.2.1.1.5.2.1.1.9Columne3FramingAISsread-onlycurrentThe number of seconds in which Alarm Indication Signals (AIS) were detected by the E3 Receive Framer block. AIS indicates that an upstream failure has been det…
1.3.6.1.4.1.326.2.2.1.1.5.2.1.1.10Columne3FramingBIP8sread-onlycurrentThe number of E3 G.832 BIP-8 errors. This counter is only valid in G.832.
1.3.6.1.4.1.326.2.2.1.1.5.2.1.1.11Columne3FramingFEBEsread-onlycurrentNumber of E3 far end block error (FEBE) events.
1.3.6.1.4.1.326.2.2.1.1.5.2.2Tablee3PlcpTablenot-accessiblecurrentA table of E3 Physical Layer Convergence Protocol (PLCP) statistics information. These statistics are only valid when the G.751 (PLCP) based framing is being u…
1.3.6.1.4.1.326.2.2.1.1.5.2.2.1Rowe3PlcpEntrynot-accessiblecurrentA table entry containing E3 PLCP statistics information.
1.3.6.1.4.1.326.2.2.1.1.5.2.2.1.1Columne3PlcpBoardread-onlycurrentThe index of this port's switch board.
1.3.6.1.4.1.326.2.2.1.1.5.2.2.1.2Columne3PlcpModuleread-onlycurrentThe network module of this port.
1.3.6.1.4.1.326.2.2.1.1.5.2.2.1.3Columne3PlcpPortread-onlycurrentThe number of this port.
1.3.6.1.4.1.326.2.2.1.1.5.2.2.1.4Columne3PlcpFERRsread-onlycurrentNumber of Physical Layer Convergence Protocol (PLCP) octet error events.
1.3.6.1.4.1.326.2.2.1.1.5.2.2.1.5Columne3PlcpLOFsread-onlycurrentThe number of seconds in which Loss Of Frame (LOF) errors were detected by the PLCP (Physical Layer Convergence Protocol) receiver. LOF is declared when an Out…
1.3.6.1.4.1.326.2.2.1.1.5.2.2.1.6Columne3PlcpBIP8sread-onlycurrentNumber of BIP-8 (Bit Interleaved Parity - 8) error events. The BIP-8 is calculated over the Path Overhead field and the associated ATM cell of the previous fra…
1.3.6.1.4.1.326.2.2.1.1.5.2.2.1.7Columne3PlcpFEBEsread-onlycurrentNumber of ATM Far End Block Error (FEBE) events.
1.3.6.1.4.1.326.2.2.1.1.5.2.2.1.8Columne3PlcpYellowsread-onlycurrentThe number of seconds in which Yellow alarm errors were detected by the PLCP (Physical Layer Convergence Protocol) receiver. Yellow alarm is asserted when 10 c…
1.3.6.1.4.1.326.2.2.1.1.5.2.3Tablee3AtmTablenot-accessiblecurrentA table of E3 ATM statistics information.
1.3.6.1.4.1.326.2.2.1.1.5.2.3.1Rowe3AtmEntrynot-accessiblecurrentA table entry containing E3 ATM statistics information.
1.3.6.1.4.1.326.2.2.1.1.5.2.3.1.1Columne3AtmBoardread-onlycurrentThe index of this port's switch board.
1.3.6.1.4.1.326.2.2.1.1.5.2.3.1.2Columne3AtmModuleread-onlycurrentThe network module of this port.
1.3.6.1.4.1.326.2.2.1.1.5.2.3.1.3Columne3AtmPortread-onlycurrentThe number of this port.
1.3.6.1.4.1.326.2.2.1.1.5.2.3.1.4Columne3AtmHCSsread-onlycurrentNumber of header check sequence (HCS) error events. The HCS is a CRC-8 calculation over the first 4 octets of the ATM cell header.
1.3.6.1.4.1.326.2.2.1.1.5.2.3.1.5Columne3AtmRxCellsread-onlycurrentNumber of ATM cells that were received.
1.3.6.1.4.1.326.2.2.1.1.5.2.3.1.6Columne3AtmTxCellsread-onlycurrentNumber of non-null ATM cells that were transmitted.
1.3.6.1.4.1.326.2.2.1.1.5.2.3.1.7Columne3AtmLCDsread-onlycurrentThe number of seconds in which Loss of Cell Delineation (LCD) has occurred. An LCD defect is detected when an out of cell delination state has persisted for 4m…