GALILEO-MIB
169 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.89.56.1 | ScalarrlGalMibVersion | read-only | mandatory | MIB's version, the current version is 1. |
| 1.3.6.1.4.1.89.56.2 | ScalarrlGalMode | read-only | mandatory | Current mode supported by the device. |
| 1.3.6.1.4.1.89.56.3 | ScalarrlGalModeAfterReset | read-write | mandatory | New mode supported by the device after the next reset. |
| 1.3.6.1.4.1.89.56.4 | NoderlPolicyGalileoDebugTuning | |||
| 1.3.6.1.4.1.89.56.4.1 | ScalarrlPolicyGalileoTuningOverProvisioning | read-write | mandatory | For non-quantitative flows: Defines the function that is used to devide the aggregate rate (dependent on the number of flows using the specific meterId). The o… |
| 1.3.6.1.4.1.89.56.4.2 | ScalarrlPolicyGalileoTuningExtremConditionBurstSize | read-write | mandatory | This variable indicates the value of a new burst size, when the given aggregate burst size has reached the following extreme condition: (aggregateBurstSize/n) … |
| 1.3.6.1.4.1.89.56.4.3 | ScalarrlPolicyGalileoTuningOverrideOutOfProfileDropPrecedence | read-write | mandatory | This mib variable is used only when the rlPolicyGalileoTuningExtremConditionBurstSize is 0 bytes. The options for this mib variables are: - TRUE => out of prof… |
| 1.3.6.1.4.1.89.56.5 | ScalarrlCosFftAgingTimeout | read-write | mandatory | The aging timeout of the CoS FFT Tables. |
| 1.3.6.1.4.1.89.56.6 | ScalarrlCosFftPollingInterval | read-write | mandatory | The polling interval for dynamic CoS FFTs support in seconds. |
| 1.3.6.1.4.1.89.56.7 | NoderlPolicyGalileoDebug | |||
| 1.3.6.1.4.1.89.56.7.1 | TablerlPolicyGalileoDebugFcogTable | not-accessible | mandatory | Indecate the instance of the fcog for hash_fnc calc per group type |
| 1.3.6.1.4.1.89.56.7.1.1 | RowrlPolicyGalileoDebugFcogEntry | not-accessible | mandatory | the entry per groupType indicate the offsets for hash_func calc. |
| 1.3.6.1.4.1.89.56.7.1.1.1 | ColumnrlPolicyGalileoDebugFcogType | read-only | mandatory | Specifies a the Group type for which Fcog bytes specified. |
| 1.3.6.1.4.1.89.56.7.1.1.2 | ColumnrlPolicyGalileoDebugL2SrcAddr | read-write | mandatory | indecate if the L2 SrcAddr defined for fcog. |
| 1.3.6.1.4.1.89.56.7.1.1.3 | ColumnrlPolicyGalileoDebugL2DstAddr | read-write | mandatory | indecate if the L2DstAddr defined for fcog. |
| 1.3.6.1.4.1.89.56.7.1.1.4 | ColumnrlPolicyGalileoDebugVlanId | read-write | mandatory | indecate if the VlanId defined for fcog. |
| 1.3.6.1.4.1.89.56.7.1.1.5 | ColumnrlPolicyGalileoDebugInport | read-write | mandatory | indecate if the Inport defined for fcog. |
| 1.3.6.1.4.1.89.56.7.1.1.6 | ColumnrlPolicyGalileoDebugIpxDstNet | read-write | mandatory | indecate if the IpxDstNet defined for fcog. |
| 1.3.6.1.4.1.89.56.7.1.1.7 | ColumnrlPolicyGalileoDebugIpxDstNode | read-write | mandatory | indecate if the IpxDstNode defined for fcog. |
| 1.3.6.1.4.1.89.56.7.1.1.8 | ColumnrlPolicyGalileoDebugIpSrcAddr | read-write | mandatory | indecate if the IpSrcAddr defined for fcog. |
| 1.3.6.1.4.1.89.56.7.1.1.9 | ColumnrlPolicyGalileoDebugIpDstAddr | read-write | mandatory | indecate if the IpDstAddr defined for fcog. |
| 1.3.6.1.4.1.89.56.7.1.1.10 | ColumnrlPolicyGalileoDebugIpProtocol | read-write | mandatory | indecate if the IpProtocol defined for fcog. |
| 1.3.6.1.4.1.89.56.7.1.1.11 | ColumnrlPolicyGalileoDebugIpSrcPort | read-write | mandatory | indecate if the IpSrcPort defined for fcog. |
| 1.3.6.1.4.1.89.56.7.1.1.12 | ColumnrlPolicyGalileoDebugIpDstPort | read-write | mandatory | indecate if the IpDstPort defined for fcog. |
| 1.3.6.1.4.1.89.56.7.1.1.13 | ColumnrlPolicyGalileoDebugStatus | read-write | mandatory | The status of a table entry. It is used to delete an entry from this table. |
| 1.3.6.1.4.1.89.56.7.2 | TablerlPolicyGalileoDebugFlowTable | not-accessible | mandatory | This table will allow us to request variables from specific entry at the flowTable. only get and getNext will be supported (getNext will return alyaws EndOfMib… |
| 1.3.6.1.4.1.89.56.7.2.1 | RowrlPolicyGalileoDebugFlowTableEntry | not-accessible | mandatory | all the input fileds has a default val except from the groupType, request of an entry should be based on the fcog definition. |
| 1.3.6.1.4.1.89.56.7.2.1.1 | ColumnrlPolicyGalileoDebugFlowType | read-only | mandatory | Specifies a the Group type. |
| 1.3.6.1.4.1.89.56.7.2.1.2 | ColumnrlPolicyGalileoDebugFlowRxIfIndex | read-only | mandatory | Specifies a the IfIndex the packet arrived (for the calculation of the relevant cosTable. |
| 1.3.6.1.4.1.89.56.7.2.1.3 | ColumnrlPolicyGalileoDebugFlowL2SrcAddr | read-only | mandatory | Indicate the L2SrcAddr for the requsted entry. |
| 1.3.6.1.4.1.89.56.7.2.1.4 | ColumnrlPolicyGalileoDebugFlowL2DstAddr | read-only | mandatory | Indicate the L2DstAddr for the requsted entry. |
| 1.3.6.1.4.1.89.56.7.2.1.5 | ColumnrlPolicyGalileoDebugFlowVlanId | read-only | mandatory | Indicate the VlanId for the requsted entry. |
| 1.3.6.1.4.1.89.56.7.2.1.6 | ColumnrlPolicyGalileoDebugFlowIpxDstNet | read-only | mandatory | Indicate the IPX DstNet for the requsted entry. |
| 1.3.6.1.4.1.89.56.7.2.1.7 | ColumnrlPolicyGalileoDebugFlowIpxDstNode | read-only | mandatory | Indicate the IPX DstNode for the requsted entry. |
| 1.3.6.1.4.1.89.56.7.2.1.8 | ColumnrlPolicyGalileoDebugFlowIpSrcAddr | read-only | mandatory | Indicate the IP SrcAddr for the requsted entry. |
| 1.3.6.1.4.1.89.56.7.2.1.9 | ColumnrlPolicyGalileoDebugFlowIpDstAddr | read-only | mandatory | Indicate the IP DstAddr for the requsted entry. |
| 1.3.6.1.4.1.89.56.7.2.1.10 | ColumnrlPolicyGalileoDebugFlowIpProtocol | read-only | mandatory | Indicate the IP Protocol for the requsted entry. |
| 1.3.6.1.4.1.89.56.7.2.1.11 | ColumnrlPolicyGalileoDebugFlowIpSrcPort | read-only | mandatory | Indicate the IP SrcPort for the requsted entry. |
| 1.3.6.1.4.1.89.56.7.2.1.12 | ColumnrlPolicyGalileoDebugFlowIpDstPort | read-only | mandatory | Indicate the IP DstPort for the requsted entry. |
| 1.3.6.1.4.1.89.56.7.2.1.13 | ColumnrlPolicyGalileoDebugFlowRetValid | read-only | mandatory | Indicate if the requsted entry is valid (exist) or not. |
| 1.3.6.1.4.1.89.56.7.2.1.14 | ColumnrlPolicyGalileoDebugFlowRetStatic | read-only | mandatory | Indicate if the requsted entry is a static entry or not. |
| 1.3.6.1.4.1.89.56.7.2.1.15 | ColumnrlPolicyGalileoDebugFlowRetAging | read-only | mandatory | Indicate if the Aging bit of the requested entry is set or not. |
| 1.3.6.1.4.1.89.56.7.2.1.16 | ColumnrlPolicyGalileoDebugFlowRetCmd | read-only | mandatory | Indicate if the CMD of the requested entry . |
| 1.3.6.1.4.1.89.56.7.2.1.17 | ColumnrlPolicyGalileoDebugFlowRetPrio | read-only | mandatory | Indicate if the Pri/Sc of the requested entry . |
| 1.3.6.1.4.1.89.56.7.2.1.18 | ColumnrlPolicyGalileoDebugFlowRetInProfileDis | read-only | mandatory | Indicate if the inProfile Discardability of the requested entry . |
| 1.3.6.1.4.1.89.56.7.2.1.19 | ColumnrlPolicyGalileoDebugFlowRetVpt | read-only | mandatory | Indicate if the Vpt of the requested entry . |
| 1.3.6.1.4.1.89.56.7.2.1.20 | ColumnrlPolicyGalileoDebugFlowRetChangeTos | read-only | mandatory | Indicate if the Change Tos of the requested entry is set or not. |
| 1.3.6.1.4.1.89.56.7.2.1.21 | ColumnrlPolicyGalileoDebugFlowRetNewTos | read-only | mandatory | Indicate if the New Tos of the requested entry. |
| 1.3.6.1.4.1.89.56.7.2.1.22 | ColumnrlPolicyGalileoDebugFlowRetVlanId | read-only | mandatory | Indicate if the VlanId of the requested entry. |
| 1.3.6.1.4.1.89.56.7.2.1.23 | ColumnrlPolicyGalileoDebugFlowRetInIfIndex | read-only | mandatory | Indicate if the InIfindex of the requested entry. |
| 1.3.6.1.4.1.89.56.7.2.1.24 | ColumnrlPolicyGalileoDebugFlowRetEnableMeter | read-only | mandatory | Indicate if Meter of the requested entry is enbled or not. |
| 1.3.6.1.4.1.89.56.7.2.1.25 | ColumnrlPolicyGalileoDebugFlowRetOutProfileDis | read-only | mandatory | Indicate the outProfile Discardability of the requested entry . |
| 1.3.6.1.4.1.89.56.8 | ScalarrlPolicyGalileoFcuFwdCpuCounter | read-only | mandatory | Count the number of packets that forward from the Flow Classification Unit to the CPU |
| 1.3.6.1.4.1.89.56.9 | NoderlPolicySimpleGalMib | |||
| 1.3.6.1.4.1.89.56.9.1 | ScalarrlPolicySimpleGalMibVersion | read-only | mandatory | MIB's version, the current version is 1. |
| 1.3.6.1.4.1.89.56.9.2 | ScalarrlPolicySimpleGalMibPortTypeSupport | read-only | mandatory | return a bit mask that indicates the supported port type: |87654321| 1 - BoundaryType 2 - InteriorType |
| 1.3.6.1.4.1.89.56.9.3 | ScalarrlPolicySimpleGalMibRecalculateRules | read-write | mandatory | Setting any value will cause recalculation of all the rules. |
| 1.3.6.1.4.1.89.56.9.4 | ScalarrlPolicySimpleGalMibPolicyEnable | read-write | mandatory | Enables or disables the policy feature |
| 1.3.6.1.4.1.89.56.9.5 | TablerlPolicySimpleGalMibProfileTable | not-accessible | mandatory | The table defines all the profiles. |
| 1.3.6.1.4.1.89.56.9.5.1 | RowrlPolicySimpleGalMibProfileEntry | not-accessible | mandatory | The entry define one profile. |
| 1.3.6.1.4.1.89.56.9.5.1.1 | ColumnrlPolicySimpleGalMibIndex | read-only | mandatory | This enumerates the table entry. |
| 1.3.6.1.4.1.89.56.9.5.1.2 | ColumnrlPolicySimpleGalMibDescription | read-write | mandatory | Informational text given by the user to describe the profile. |
| 1.3.6.1.4.1.89.56.9.5.1.3 | ColumnrlPolicySimpleGalMibProfileType | read-write | mandatory | Specifies a profile type. |
| 1.3.6.1.4.1.89.56.9.5.1.4 | ColumnrlPolicySimpleGalMibRate | read-write | mandatory | The rate in kilobytes/second for the specified profile, or in the case of minDelay per session profile type the rate will indicate the rate per individual sess… |
| 1.3.6.1.4.1.89.56.9.5.1.5 | ColumnrlPolicySimpleGalMibBurstSize | read-write | mandatory | The burst size parameter. A value of 0 means that the device should choose the Burst Size that is most suitable for the profile. |
| 1.3.6.1.4.1.89.56.9.5.1.6 | ColumnrlPolicySimpleGalMibMaxSession | read-write | mandatory | Relevant only for the minDelay per session. Indicate the maximum number of sessions for this profile. |
| 1.3.6.1.4.1.89.56.9.5.1.7 | ColumnrlPolicySimpleGalMibNewVpt | read-write | mandatory | Indicates the new VPT to assign to the packet. |
| 1.3.6.1.4.1.89.56.9.5.1.8 | ColumnrlPolicySimpleGalMibChangeTosOrDscp | read-write | mandatory | Indicates whether the TOS or DSCP should be remarked with a new value |
| 1.3.6.1.4.1.89.56.9.5.1.9 | ColumnrlPolicySimpleGalMibNewTosOrDscp | read-write | mandatory | Indicates the new value for the TOS or DSCP. Relevant only if rlPolicySimpleGalMibChangeTosOrDscp is true. |
| 1.3.6.1.4.1.89.56.9.5.1.10 | ColumnrlPolicySimpleGalMibStatus | read-write | mandatory | The status of a table entry. It is used to delete an entry from this table. |
| 1.3.6.1.4.1.89.56.9.6 | TablerlPolicySimpleGalMibIpFcogTable | not-accessible | mandatory | This table defines the used fields for ip classification, per port type (interior/boundary) |
| 1.3.6.1.4.1.89.56.9.6.1 | RowrlPolicySimpleGalMibIpFcogEntry | not-accessible | mandatory | the entry define the used fields for classification |
| 1.3.6.1.4.1.89.56.9.6.1.1 | ColumnrlPolicySimpleGalMibIpFcogPortType | read-only | mandatory | The port type (interior/boundary) to which this entry applies. |
| 1.3.6.1.4.1.89.56.9.6.1.2 | ColumnrlPolicySimpleGalMibIpFcogTosOrDscp | read-write | mandatory | Indicates whether the IP TOS or DSCP field will be used in classifiers or not. |
| 1.3.6.1.4.1.89.56.9.6.1.3 | ColumnrlPolicySimpleGalMibIpFcogProtocol | read-write | mandatory | Indicates whether the IP L4 protocol field will be used in classifiers or not. |
| 1.3.6.1.4.1.89.56.9.6.1.4 | ColumnrlPolicySimpleGalMibIpFcogSrcIpMask | read-write | mandatory | Indicates the number of most significant bits of the Ip Address that are used in specifying IP source addresses in classifiers. |
| 1.3.6.1.4.1.89.56.9.6.1.5 | ColumnrlPolicySimpleGalMibIpFcogDstIpMask | read-write | mandatory | Indicates the number of most significant bits of the Ip Address that are used in specifying IP destination addresses in classifiers. |
| 1.3.6.1.4.1.89.56.9.6.1.6 | ColumnrlPolicySimpleGalMibIpFcogSrcPort | read-write | mandatory | Indicates whether the IP L4 protocol source port field will be used in classifiers or not. |
| 1.3.6.1.4.1.89.56.9.6.1.7 | ColumnrlPolicySimpleGalMibIpFcogDstPort | read-write | mandatory | Indicates whether the IP L4 protocol destination port field will be used in classifiers or not. |
| 1.3.6.1.4.1.89.56.9.6.1.8 | ColumnrlPolicySimpleGalMibIpFcogInIfIndex | read-write | mandatory | Indicates whether ifIndex of input ports will be used in classifiers or not. |
| 1.3.6.1.4.1.89.56.9.7 | TablerlPolicySimpleGalMibIpRulesTable | not-accessible | mandatory | This table contains the policy rules defined by the user. The order of the entries in the table is important, since the first rule that applies to the incoming… |
| 1.3.6.1.4.1.89.56.9.7.1 | RowrlPolicySimpleGalMibIpRulesEntry | not-accessible | mandatory | This entry defines one policy rule. |
| 1.3.6.1.4.1.89.56.9.7.1.1 | ColumnrlPolicySimpleGalMibIpRulesPortType | read-only | mandatory | The port type (interior/boundary) to which this rule applies. |
| 1.3.6.1.4.1.89.56.9.7.1.2 | ColumnrlPolicySimpleGalMibIpRulesIndex | read-only | mandatory | This enumerates the table. The user should assign indices in such a way that there will be a gap big enough between one rule and the next to allow insertion of… |
| 1.3.6.1.4.1.89.56.9.7.1.3 | ColumnrlPolicySimpleGalMibIpRulesDescription | read-write | mandatory | Informational text given by the user to describe the rule. |
| 1.3.6.1.4.1.89.56.9.7.1.4 | ColumnrlPolicySimpleGalMibIpRulesTosOrDscp | read-write | mandatory | Indicates the TOS or DSCP to compare with. |
| 1.3.6.1.4.1.89.56.9.7.1.5 | ColumnrlPolicySimpleGalMibIpRulesProtocol | read-write | mandatory | Indicates the L4 protocol to compare with. |
| 1.3.6.1.4.1.89.56.9.7.1.6 | ColumnrlPolicySimpleGalMibIpRulesSrcIp | read-write | mandatory | Indicates the source IP address to compare with. |
| 1.3.6.1.4.1.89.56.9.7.1.7 | ColumnrlPolicySimpleGalMibIpRulesSrcIpMask | read-write | mandatory | Indicates the number of most significant bits of the Ip Address that are used in specifying IP source addresses in classifiers. |
| 1.3.6.1.4.1.89.56.9.7.1.8 | ColumnrlPolicySimpleGalMibIpRulesDstIp | read-write | mandatory | Indicates the destination IP address to compare with. |
| 1.3.6.1.4.1.89.56.9.7.1.9 | ColumnrlPolicySimpleGalMibIpRulesDstIpMask | read-write | mandatory | Indicates the number of most significant bits of the Ip Address that are used in specifying IP destination addresses in classifiers. |
| 1.3.6.1.4.1.89.56.9.7.1.10 | ColumnrlPolicySimpleGalMibIpRulesSrcPort | read-write | mandatory | Indicates the source L4 port to compare with. |
| 1.3.6.1.4.1.89.56.9.7.1.11 | ColumnrlPolicySimpleGalMibIpRulesDstPort | read-write | mandatory | Indicates the destination L4 port to compare with. |
| 1.3.6.1.4.1.89.56.9.7.1.12 | ColumnrlPolicySimpleGalMibIpRulesInIfIndexList | read-write | mandatory | Indicates the list of input ports to which this rule applies. |
| 1.3.6.1.4.1.89.56.9.7.1.13 | ColumnrlPolicySimpleGalMibIpRulesCondition | read-write | mandatory | Indicate the relation that should hold for each relevant field of the rule in comparison to the packet's field. |
| 1.3.6.1.4.1.89.56.9.7.1.14 | ColumnrlPolicySimpleGalMibIpRulesAction | read-write | mandatory | Indicates the action to be performed if there is a match with the rule. |
| 1.3.6.1.4.1.89.56.9.7.1.15 | ColumnrlPolicySimpleGalMibIpRulesProfilePointer | read-write | mandatory | Indicates the profile attached to the rule. The value is the index in the profile table of the attached profile. Value 0 means that no profile is attached to t… |
| 1.3.6.1.4.1.89.56.9.7.1.16 | ColumnrlPolicySimpleGalMibIpRulesOutIfIndexList | read-write | mandatory | Indicates the list of output ports to on which bandwidth should be allocated for this rule. |
| 1.3.6.1.4.1.89.56.9.7.1.17 | ColumnrlPolicySimpleGalMibIpRulesBitsUsed | read-write | mandatory | a bit mask that indicates the the used fields for the entry: (the implemention is identical to BITS implementation,from MSB to LSB) |87654321| 8 - tosOrDscp 7 … |
| 1.3.6.1.4.1.89.56.9.7.1.18 | ColumnrlPolicySimpleGalMibIpRulesErrorDescrip | read-only | mandatory | A description error indicate the user about the specific error. The error can cause by one of the following reasons: 1. if the profile was asign to the rule co… |
| 1.3.6.1.4.1.89.56.9.7.1.19 | ColumnrlPolicySimpleGalMibIpRulesStatus | read-write | mandatory | The status of a table entry. It is used to delete an entry from this table. notInService is used to disable an entry. notReady will be assigned by the device t… |
| 1.3.6.1.4.1.89.56.9.8 | TablerlPolicySimpleGalMibIpxFcogTable | not-accessible | mandatory | This table defines the used fields for ipx classification |
| 1.3.6.1.4.1.89.56.9.8.1 | RowrlPolicySimpleGalMibIpxFcogEntry | not-accessible | mandatory | the entry defines the used fields for classification |
| 1.3.6.1.4.1.89.56.9.8.1.1 | ColumnrlPolicySimpleGalMibIpxFcogIndex | read-only | mandatory | the table index - only one entry exist |
| 1.3.6.1.4.1.89.56.9.8.1.2 | ColumnrlPolicySimpleGalMibIpxFcogDstNet | read-write | mandatory | Indicates the parts of the field in use in the rules |
| 1.3.6.1.4.1.89.56.9.8.1.3 | ColumnrlPolicySimpleGalMibIpxFcogDstNode | read-write | mandatory | Indicates the parts of the field in use in the rules |
| 1.3.6.1.4.1.89.56.9.8.1.4 | ColumnrlPolicySimpleGalMibIpxFcogDstSocket | read-write | mandatory | Indicates whether the field is in use in the rules |
| 1.3.6.1.4.1.89.56.9.8.1.5 | ColumnrlPolicySimpleGalMibIpxFcogSrcNet | read-write | mandatory | Indicates the parts of the field in use in the rules |
| 1.3.6.1.4.1.89.56.9.8.1.6 | ColumnrlPolicySimpleGalMibIpxFcogSrcNode | read-write | mandatory | Indicates the parts of the field in use in the rules |
| 1.3.6.1.4.1.89.56.9.8.1.7 | ColumnrlPolicySimpleGalMibIpxFcogSrcSocket | read-write | mandatory | Indicates whether the field is in use in the rules |
| 1.3.6.1.4.1.89.56.9.8.1.8 | ColumnrlPolicySimpleGalMibIpxFcogInIfIndex | read-write | mandatory | Indicates whether the field is in use in the rules |
| 1.3.6.1.4.1.89.56.9.9 | TablerlPolicySimpleGalMibIpxRulesTable | not-accessible | mandatory | This table contains the policy rules defined by the user. The order of the entries in the table is important, since the first rule that matches the incoming pa… |
| 1.3.6.1.4.1.89.56.9.9.1 | RowrlPolicySimpleGalMibIpxRulesEntry | not-accessible | mandatory | This entry defines one policy rule. |
| 1.3.6.1.4.1.89.56.9.9.1.1 | ColumnrlPolicySimpleGalMibIpxRulesIndex | read-only | mandatory | This enumerates the table. The user should assign indices in such a way that there will be a gap big enough between one rule and the next to allow insertion of… |
| 1.3.6.1.4.1.89.56.9.9.1.2 | ColumnrlPolicySimpleGalMibIpxRulesDescription | read-write | mandatory | Informational text given by the user to describe the rule. |
| 1.3.6.1.4.1.89.56.9.9.1.3 | ColumnrlPolicySimpleGalMibIpxRulesDstNet | read-write | mandatory | Indicate the ipxDst Net to compare to |
| 1.3.6.1.4.1.89.56.9.9.1.4 | ColumnrlPolicySimpleGalMibIpxRulesDstNode | read-write | mandatory | Indicate the ipxDstNode to compare to |
| 1.3.6.1.4.1.89.56.9.9.1.5 | ColumnrlPolicySimpleGalMibIpxRulesDstSocket | read-write | mandatory | Indicate the ipx DstSocket to compare to |
| 1.3.6.1.4.1.89.56.9.9.1.6 | ColumnrlPolicySimpleGalMibIpxRulesSrcNet | read-write | mandatory | Indicate the ipxSrc Net to compare to |
| 1.3.6.1.4.1.89.56.9.9.1.7 | ColumnrlPolicySimpleGalMibIpxRulesSrcNode | read-write | mandatory | Indicate the ipxSrcNode to compare to |
| 1.3.6.1.4.1.89.56.9.9.1.8 | ColumnrlPolicySimpleGalMibIpxRulesSrcSocket | read-write | mandatory | Indicate the ipx SrcSocket to compare to |
| 1.3.6.1.4.1.89.56.9.9.1.9 | ColumnrlPolicySimpleGalMibIpxRulesInIfIndexList | read-write | mandatory | Indicates the list of input ports to which this rule applies. |
| 1.3.6.1.4.1.89.56.9.9.1.10 | ColumnrlPolicySimpleGalMibIpxRulesCondition | read-write | mandatory | Indicate the relation that should hold for each relevant field of the rule in comparison to the packet's. |
| 1.3.6.1.4.1.89.56.9.9.1.11 | ColumnrlPolicySimpleGalMibIpxRulesAction | read-write | mandatory | Indicates the action to be performed if the rule matches. |
| 1.3.6.1.4.1.89.56.9.9.1.12 | ColumnrlPolicySimpleGalMibIpxRulesProfilePointer | read-write | mandatory | Indicates the profile attached to the rule. The value is the index in the profile table of the attached profile. Value 0 means that no profile is attached to t… |
| 1.3.6.1.4.1.89.56.9.9.1.13 | ColumnrlPolicySimpleGalMibIpxRulesOutIfIndexList | read-write | mandatory | Indicates the list of output ports on which bandwidth should be allocated for this rule. |
| 1.3.6.1.4.1.89.56.9.9.1.14 | ColumnrlPolicySimpleGalMibIpxRulesStatus | read-write | mandatory | The status of a table entry. It is used to delete an entry from this table. notInService is used to disable an entry. notReady will be assigned by the device t… |
| 1.3.6.1.4.1.89.56.9.10 | TablerlPolicySimpleGalMibBridgeFcogTable | not-accessible | mandatory | The table defines the used fields for Bridge classification |
| 1.3.6.1.4.1.89.56.9.10.1 | RowrlPolicySimpleGalMibBridgeFcogEntry | not-accessible | mandatory | the entry defines the used fields for classification |
| 1.3.6.1.4.1.89.56.9.10.1.1 | ColumnrlPolicySimpleGalMibBridgeFcogIndex | read-only | mandatory | the table index - only one entry exist |
| 1.3.6.1.4.1.89.56.9.10.1.2 | ColumnrlPolicySimpleGalMibBridgeFcogDstMac | read-write | mandatory | Indicate the use of the field in the rules |
| 1.3.6.1.4.1.89.56.9.10.1.3 | ColumnrlPolicySimpleGalMibBridgeFcogSrcMac | read-write | mandatory | Indicate the use of the field in the rules |
| 1.3.6.1.4.1.89.56.9.10.1.4 | ColumnrlPolicySimpleGalMibBridgeFcogVid | read-write | mandatory | Indicate whether the field is in use in the rules |
| 1.3.6.1.4.1.89.56.9.10.1.5 | ColumnrlPolicySimpleGalMibBridgeFcogInIfIndex | read-write | mandatory | Indicate whether the field is in use in the rules |
| 1.3.6.1.4.1.89.56.9.10.1.6 | ColumnrlPolicySimpleGalMibBridgeFcogEthType | read-write | mandatory | Indicate whether the field is in use in the rules |
| 1.3.6.1.4.1.89.56.9.10.1.7 | ColumnrlPolicySimpleGalMibBridgeFcogIpTosOrDscp | read-write | mandatory | Indicate whether the field is in use in the rules |
| 1.3.6.1.4.1.89.56.9.10.1.8 | ColumnrlPolicySimpleGalMibBridgeFcogIpProtocol | read-write | mandatory | Indicate whether the field is in use in the rules |
| 1.3.6.1.4.1.89.56.9.10.1.9 | ColumnrlPolicySimpleGalMibBridgeFcogIpSrcIpMask | read-write | mandatory | Indicate the number of used bits of the Ip Address from the left |
| 1.3.6.1.4.1.89.56.9.10.1.10 | ColumnrlPolicySimpleGalMibBridgeFcogIpDstIpMask | read-write | mandatory | Indicate the number of used bits of the Ip Address from the left |
| 1.3.6.1.4.1.89.56.9.10.1.11 | ColumnrlPolicySimpleGalMibBridgeFcogIpSrcPort | read-write | mandatory | Indicate whether the field is in use in the rules |
| 1.3.6.1.4.1.89.56.9.10.1.12 | ColumnrlPolicySimpleGalMibBridgeFcogIpDstPort | read-write | mandatory | Indicate whether the field is in use in the rules |
| 1.3.6.1.4.1.89.56.9.11 | TablerlPolicySimpleGalMibBridgeRulesTable | not-accessible | mandatory | This table contains the policy rules defined by the user. The order of the entries in the table is important, since the first rule that applies to the incoming… |
| 1.3.6.1.4.1.89.56.9.11.1 | RowrlPolicySimpleGalMibBridgeRulesEntry | not-accessible | mandatory | This entry defines one policy rule. |
| 1.3.6.1.4.1.89.56.9.11.1.1 | ColumnrlPolicySimpleGalMibBridgeRulesIndex | read-only | mandatory | This enumerates the table. The user should assign indices in such a way that there will be a gap big enough between one rule and the next to allow insertion of… |
| 1.3.6.1.4.1.89.56.9.11.1.2 | ColumnrlPolicySimpleGalMibBridgeRulesDescription | read-write | mandatory | Informational text given by the user to describe the rule. |
| 1.3.6.1.4.1.89.56.9.11.1.3 | ColumnrlPolicySimpleGalMibBridgeRulesDstMac | read-write | mandatory | Indicate the Dst mac to compare |
| 1.3.6.1.4.1.89.56.9.11.1.4 | ColumnrlPolicySimpleGalMibBridgeRulesSrcMac | read-write | mandatory | Indicate the source mac to compare |
| 1.3.6.1.4.1.89.56.9.11.1.5 | ColumnrlPolicySimpleGalMibBridgeRulesVid | read-write | mandatory | Indicate the vlanId to compare |
| 1.3.6.1.4.1.89.56.9.11.1.6 | ColumnrlPolicySimpleGalMibBridgeRulesInIfIndexList | read-write | mandatory | Indicates the list of input ports to which this rule applies. |
| 1.3.6.1.4.1.89.56.9.11.1.7 | ColumnrlPolicySimpleGalMibBridgeRulesEthType | read-write | mandatory | Indicate the Ethernet type of the packet |
| 1.3.6.1.4.1.89.56.9.11.1.8 | ColumnrlPolicySimpleGalMibBridgeRulesIpTosOrDscp | read-write | mandatory | Indicates the tos or dscp to compare |
| 1.3.6.1.4.1.89.56.9.11.1.9 | ColumnrlPolicySimpleGalMibBridgeRulesIpProtocol | read-write | mandatory | Indicates the protocol to compare |
| 1.3.6.1.4.1.89.56.9.11.1.10 | ColumnrlPolicySimpleGalMibBridgeRulesIpSrcIp | read-write | mandatory | Indicate the srcIp to compare |
| 1.3.6.1.4.1.89.56.9.11.1.11 | ColumnrlPolicySimpleGalMibBridgeRulesIpDstIp | read-write | mandatory | Indicate the DstIp to compare |
| 1.3.6.1.4.1.89.56.9.11.1.12 | ColumnrlPolicySimpleGalMibBridgeRulesIpSrcPort | read-write | mandatory | Indicate the Src port to compare |
| 1.3.6.1.4.1.89.56.9.11.1.13 | ColumnrlPolicySimpleGalMibBridgeRulesIpDstPort | read-write | mandatory | Indicate the Src port to compare |
| 1.3.6.1.4.1.89.56.9.11.1.14 | ColumnrlPolicySimpleGalMibBridgeRulesCondition | read-write | mandatory | Indicate the relation that should hold for each relevant field of the rule in comparison to the packet's field. |
| 1.3.6.1.4.1.89.56.9.11.1.15 | ColumnrlPolicySimpleGalMibBridgeRulesAction | read-write | mandatory | Indicates the action to be performed if there is a match with the rule. |
| 1.3.6.1.4.1.89.56.9.11.1.16 | ColumnrlPolicySimpleGalMibBridgeRulesProfilePointer | read-write | mandatory | Indicates the profile attached to the rule. The value is the index in the profile table of the attached profile. Value 0 means that no profile is attached to t… |
| 1.3.6.1.4.1.89.56.9.11.1.17 | ColumnrlPolicySimpleGalMibBridgeRulesOutIfIndexList | read-write | mandatory | Indicates the list of output ports to on which bandwidth should be allocated for this rule. |
| 1.3.6.1.4.1.89.56.9.11.1.18 | ColumnrlPolicySimpleGalMibBridgeRulesStatus | read-write | mandatory | The status of a table entry. It is used to delete an entry from this table. notInService is used to disable an entry. notReady will be assigned by the device t… |
| 1.3.6.1.4.1.89.56.9.12 | TablerlPolicySimpleGalMibPortTable | not-accessible | mandatory | The table defines all of the ports types |
| 1.3.6.1.4.1.89.56.9.12.1 | RowrlPolicySimpleGalMibPortEntry | not-accessible | mandatory | An entry defines a port's type |
| 1.3.6.1.4.1.89.56.9.12.1.1 | ColumnrlPolicySimpleGalMibPortIfIndex | read-only | mandatory | This enumerates the table entry. |
| 1.3.6.1.4.1.89.56.9.12.1.2 | ColumnrlPolicySimpleGalMibPortType | read-write | mandatory | Defines the port type |
| 1.3.6.1.4.1.89.56.10 | ScalarrlGalPolicyMode | read-only | mandatory | Indicates whether the QoS is for: -All Bridged packets; or -All routed IP packets. The value cannot change after system init |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| RlPolicyGalileoDebugGroupType | INTEGER { bridged(1), routedIp(2), routedIpx(3) } | current | Specifies one of 3 types for which offset bytes can be specified. For Ip,bridge and Ipx |
| RlPolicySimpleGalMibPortType | INTEGER { boundary(1), interior(2) } | current | Specifies the port type |
| RlPolicySimpleGalMibProfileType | INTEGER { minBandwidth(1), bandwidthGuarantee(2), minDelay(3), minDelayPerSession(4) } | current | Specifies one of 4 services the device can support |