HH3C-IF-EXT-MIB
376 objects
This MIB is an extension of interface MIBs such as IF-MIB. This MIB is applicable to routers, switches, and other products. Some objects in this MIB may be used only for some specific products, so users should refer to the related documents to acquire more detailed information.
Imported Objects
| HCNUM-TC | CounterBasedGauge64 |
| HH3C-OID-MIB | hh3cCommon |
| IF-MIB | ifDescr ifIndex InterfaceIndex |
| SNMPv2-SMI | Counter64 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | DisplayString RowStatus TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.25506.2.40 | Identityhh3cIfExt | This MIB is an extension of interface MIBs such as IF-MIB. This MIB is applicable to routers, switches, and other products. Some objects in this MIB may be use… | ||
| 1.3.6.1.4.1.25506.2.40.1 | Nodehh3cIfExtScalarGroup | |||
| 1.3.6.1.4.1.25506.2.40.1.1 | Scalarhh3cIfStatGlobalFlowInterval | read-write | current | Sampling interval for in/out flow of all interfaces. Setting zero indicates closing the statistic function. |
| 1.3.6.1.4.1.25506.2.40.1.2 | Scalarhh3cIfShutDownInterval | read-write | current | Set the port status detection timer. The device starts a port status detection timer when a port is shut down by a protocol. Once the timer expires, the device… |
| 1.3.6.1.4.1.25506.2.40.1.3 | Scalarhh3cIfThroughputInKbps | read-only | current | Actual incoming throughput of the device in kbps. |
| 1.3.6.1.4.1.25506.2.40.1.4 | Scalarhh3cIfThroughputOutKbps | read-only | current | Actual outgoing throughput of the device in kbps. |
| 1.3.6.1.4.1.25506.2.40.1.5 | Scalarhh3cIfRate | accessible-for-notify | current | The rate of the actual bandwidth for an interface. |
| 1.3.6.1.4.1.25506.2.40.1.6 | Scalarhh3cIfChassisIndex | accessible-for-notify | current | Chassis. |
| 1.3.6.1.4.1.25506.2.40.1.7 | Scalarhh3cIfSlotIndex | accessible-for-notify | current | Slot. |
| 1.3.6.1.4.1.25506.2.40.1.8 | Scalarhh3cIfSubSlotIndex | accessible-for-notify | current | Subslot. |
| 1.3.6.1.4.1.25506.2.40.1.9 | Scalarhh3cIfErrDownDesc | accessible-for-notify | current | Interface error down reason. |
| 1.3.6.1.4.1.25506.2.40.1.10 | Scalarhh3cIfLoopBackType | accessible-for-notify | current | Loopback type. |
| 1.3.6.1.4.1.25506.2.40.1.11 | Scalarhh3cIfTtlLoopThreshold | accessible-for-notify | current | Ttl threshold for loop prevention. |
| 1.3.6.1.4.1.25506.2.40.1.12 | Scalarhh3cIfPreDataLowByte | accessible-for-notify | current | Previous lower 32-bit value. |
| 1.3.6.1.4.1.25506.2.40.1.13 | Scalarhh3cIfPreDataHighByte | accessible-for-notify | current | Previous higher 32-bit value. |
| 1.3.6.1.4.1.25506.2.40.1.14 | Scalarhh3cIfCurDataLowByte | accessible-for-notify | current | Current lower 32-bit value. |
| 1.3.6.1.4.1.25506.2.40.1.15 | Scalarhh3cIfCurDataHighByte | accessible-for-notify | current | Current higher 32-bit value. |
| 1.3.6.1.4.1.25506.2.40.1.16 | Scalarhh3cIfIntervalTime | accessible-for-notify | current | Interval. |
| 1.3.6.1.4.1.25506.2.40.1.17 | Scalarhh3cIfSDHHpIndex | accessible-for-notify | current | SDH high-order path index. |
| 1.3.6.1.4.1.25506.2.40.1.18 | Scalarhh3cIfUNUCPortRealFlow | accessible-for-notify | current | Percentage of unknown unicast traffic to total traffic. |
| 1.3.6.1.4.1.25506.2.40.1.19 | Scalarhh3cIfUNUCPortAlarmThreshold | accessible-for-notify | current | Unknow unicast traffic threshold for an interface, in percentage. |
| 1.3.6.1.4.1.25506.2.40.1.20 | Scalarhh3cIfBip8SdErrThreshold | accessible-for-notify | current | The threshold for BIP8 error-code. |
| 1.3.6.1.4.1.25506.2.40.1.21 | Scalarhh3cIfCpuId | accessible-for-notify | current | CPU ID. |
| 1.3.6.1.4.1.25506.2.40.1.22 | Scalarhh3cIfOldComboType | accessible-for-notify | current | Combo type before switching. |
| 1.3.6.1.4.1.25506.2.40.1.23 | Scalarhh3cIfNewComboType | accessible-for-notify | current | Combo type after switching. |
| 1.3.6.1.4.1.25506.2.40.1.24 | Scalarhh3cIfDropRateThreshold | accessible-for-notify | current | Packet loss rate threshold. |
| 1.3.6.1.4.1.25506.2.40.1.25 | Scalarhh3cIfCurrentDropRate | accessible-for-notify | current | Current packet loss rate. |
| 1.3.6.1.4.1.25506.2.40.1.26 | Scalarhh3cIfDropRateInterval | accessible-for-notify | current | Packet loss rate detection interval. |
| 1.3.6.1.4.1.25506.2.40.1.27 | Scalarhh3cIfMessageProtocol | accessible-for-notify | current | Message protocol. |
| 1.3.6.1.4.1.25506.2.40.1.28 | Scalarhh3cIfCurrentFlowThreshold | accessible-for-notify | current | Current bursty flow threshold. |
| 1.3.6.1.4.1.25506.2.40.1.29 | Scalarhh3cIfCurrentFlowValue | accessible-for-notify | current | Current bursty flow value. |
| 1.3.6.1.4.1.25506.2.40.1.30 | Scalarhh3cIfCurrentUsedRatio | accessible-for-notify | current | Current queue depth usage rate. |
| 1.3.6.1.4.1.25506.2.40.1.31 | Scalarhh3cIfUsedRatioThreshold | accessible-for-notify | current | Queue depth usage threshold. |
| 1.3.6.1.4.1.25506.2.40.1.32 | Scalarhh3cIfDiscardType | accessible-for-notify | current | Packet loss type. |
| 1.3.6.1.4.1.25506.2.40.1.33 | Scalarhh3cIfDiscardThreshold | accessible-for-notify | current | Packet loss threshold. |
| 1.3.6.1.4.1.25506.2.40.2 | Nodehh3cIfExtGroup | |||
| 1.3.6.1.4.1.25506.2.40.2.1 | Nodehh3cIfStat | |||
| 1.3.6.1.4.1.25506.2.40.2.1.1 | Nodehh3cIfStatScalarGroup | |||
| 1.3.6.1.4.1.25506.2.40.2.1.2 | Nodehh3cIfStatTable | |||
| 1.3.6.1.4.1.25506.2.40.2.1.2.1 | Tablehh3cIfFlowStatTable | not-accessible | current | This table contains objects to get statistic information of interfaces on a device. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.1.1 | Rowhh3cIfFlowStatEntry | not-accessible | current | Entry items |
| 1.3.6.1.4.1.25506.2.40.2.1.2.1.1.1 | Columnhh3cIfStatFlowInterval | read-write | current | Sampling interval for in/out flow of interface. Setting zero indicates closing this statistic function and objects in this table should return 0. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.1.1.2 | Columnhh3cIfStatFlowInBits | read-only | current | In bits in the specified interval. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.1.1.3 | Columnhh3cIfStatFlowOutBits | read-only | current | Out bits in the specified interval. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.1.1.4 | Columnhh3cIfStatFlowInPkts | read-only | current | In packets in the specified interval. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.1.1.5 | Columnhh3cIfStatFlowOutPkts | read-only | current | Out packets in the specified interval. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.1.1.6 | Columnhh3cIfStatFlowInBytes | read-only | current | In bytes in the specified interval. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.1.1.7 | Columnhh3cIfStatFlowOutBytes | read-only | current | Out bytes in the specified interval. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.2 | Tablehh3cIfSpeedStatTable | not-accessible | current | This table contains objects to get average speed information in the specified interval for interfaces on a device. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.2.1 | Rowhh3cIfSpeedStatEntry | not-accessible | current | Entry items |
| 1.3.6.1.4.1.25506.2.40.2.1.2.2.1.1 | Columnhh3cIfSpeedStatInterval | read-write | current | Sampling interval for in/out flow of interface. Setting zero indicates closing this statistic function and objects in this table should return 0. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.2.1.2 | Columnhh3cIfSpeedStatInPkts | read-only | current | Average of input packets per second in the interval specified by hh3cIfSpeedStatInterval. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.2.1.3 | Columnhh3cIfSpeedStatOutPkts | read-only | current | Average of output packets per second in the interval specified by hh3cIfSpeedStatInterval. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.2.1.4 | Columnhh3cIfSpeedStatInBytes | read-only | current | Average of input bytes per second in the interval specified by hh3cIfSpeedStatInterval. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.2.1.5 | Columnhh3cIfSpeedStatOutBytes | read-only | current | Average of output bytes per second in the interval specified by hh3cIfSpeedStatInterval. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.2.1.6 | Columnhh3cIfSpeedStatInBits | read-only | current | Average of input bits per second in the interval specified by hh3cIfSpeedStatInterval. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.2.1.7 | Columnhh3cIfSpeedStatOutBits | read-only | current | Average of output bits per second in the interval specified by hh3cIfSpeedStatInterval. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.3 | Tablehh3cIfHCFlowStatTable | not-accessible | current | This table contains objects to get statistic information of interfaces on a device. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.3.1 | Rowhh3cIfHCFlowStatEntry | not-accessible | current | Entry items |
| 1.3.6.1.4.1.25506.2.40.2.1.2.3.1.1 | Columnhh3cIfStatFlowHCInBits | read-only | current | In bits in the specified interval. This object is a 64-bit version of hh3cIfStatFlowInBits. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.3.1.2 | Columnhh3cIfStatFlowHCOutBits | read-only | current | Out bits in the specified interval. This object is a 64-bit version of hh3cIfStatFlowOutBits. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.3.1.3 | Columnhh3cIfStatFlowHCInPkts | read-only | current | In packets in the specified interval. This object is a 64-bit version of hh3cIfStatFlowInPkts. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.3.1.4 | Columnhh3cIfStatFlowHCOutPkts | read-only | current | Out packets in the specified interval. This object is a 64-bit version of hh3cIfStatFlowOutPkts. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.3.1.5 | Columnhh3cIfStatFlowHCInBytes | read-only | current | In bytes in the specified interval. This object is a 64-bit version of hh3cIfStatFlowInBytes. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.3.1.6 | Columnhh3cIfStatFlowHCOutBytes | read-only | current | Out bytes in the specified interval. This object is a 64-bit version of hh3cIfStatFlowOutBytes. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.4 | Tablehh3cIfHCSpeedStatTable | not-accessible | current | This table contains objects to get average speed information in the specified interval for interfaces on a device. This table is a 64-bit version of hh3cIfSpee… |
| 1.3.6.1.4.1.25506.2.40.2.1.2.4.1 | Rowhh3cIfHCSpeedStatEntry | not-accessible | current | Entry items |
| 1.3.6.1.4.1.25506.2.40.2.1.2.4.1.1 | Columnhh3cIfSpeedStatHCInPkts | read-only | current | Average of input packets per second in the interval specified by hh3cIfSpeedStatInterval. This object is a 64-bit version of hh3cIfSpeedStatInPkts. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.4.1.2 | Columnhh3cIfSpeedStatHCOutPkts | read-only | current | Average of output packets per second in the interval specified by hh3cIfSpeedStatInterval. This object is a 64-bit version of hh3cIfSpeedStatOutPkts. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.4.1.3 | Columnhh3cIfSpeedStatHCInBytes | read-only | current | Average of input bytes per second in the interval specified by hh3cIfSpeedStatInterval. This object is a 64-bit version of hh3cIfSpeedStatInBytes. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.4.1.4 | Columnhh3cIfSpeedStatHCOutBytes | read-only | current | Average of output bytes per second in the interval specified by hh3cIfSpeedStatInterval. This object is a 64-bit version of hh3cIfSpeedStatOutBytes. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.4.1.5 | Columnhh3cIfSpeedStatHCInBits | read-only | current | Average of input bits per second in the interval specified by hh3cIfSpeedStatInterval. This object is a 64-bit version of hh3cIfSpeedStatInBits. |
| 1.3.6.1.4.1.25506.2.40.2.1.2.4.1.6 | Columnhh3cIfSpeedStatHCOutBits | read-only | current | Average of output bits per second in the interval specified by hh3cIfSpeedStatInterval. This object is a 64-bit version of hh3cIfSpeedStatOutBits. |
| 1.3.6.1.4.1.25506.2.40.2.2 | Nodehh3cIfControl | |||
| 1.3.6.1.4.1.25506.2.40.2.2.1 | Tablehh3cRTParentIfTable | not-accessible | current | This table contains all interfaces that can create subinterfaces. |
| 1.3.6.1.4.1.25506.2.40.2.2.1.1 | Rowhh3cRTParentIfEntry | not-accessible | current | This entry describes an interface that can create subinterfaces. |
| 1.3.6.1.4.1.25506.2.40.2.2.1.1.1 | Columnhh3cRTParentIfIndex | not-accessible | current | The index of the interface that can create subinterfaces. The value is the same as the ifIndex value for this interface. |
| 1.3.6.1.4.1.25506.2.40.2.2.1.1.2 | Columnhh3cRTMinSubIfOrdinal | read-only | current | The min ordinal of the subinterface. |
| 1.3.6.1.4.1.25506.2.40.2.2.1.1.3 | Columnhh3cRTMaxSubIfOrdinal | read-only | current | The max ordinal of the subinterface. |
| 1.3.6.1.4.1.25506.2.40.2.2.2 | Tablehh3cRTSubIfTable | not-accessible | current | This table contains objects to create or delete subinterfaces. To create a subinterface, a valid parent interface must be specified by hh3cRTSubIfParentIfIndex… |
| 1.3.6.1.4.1.25506.2.40.2.2.2.1 | Rowhh3cRTSubIfEntry | not-accessible | current | The hh3cRTSubIfTable entry items |
| 1.3.6.1.4.1.25506.2.40.2.2.2.1.1 | Columnhh3cRTSubIfParentIfIndex | not-accessible | current | The parent interface index. The value should be the same as hh3cRTParentIfIndex. |
| 1.3.6.1.4.1.25506.2.40.2.2.2.1.2 | Columnhh3cRTSubIfOrdinal | not-accessible | current | The ordinal of the subinterface. It should between hh3cRTMinSubIfOrdinal and hh3cRTMaxSubIfOrdinal of the parent interface. |
| 1.3.6.1.4.1.25506.2.40.2.2.2.1.3 | Columnhh3cRTSubIfSubIfIndex | read-only | current | The ifIndex value of the subinterface |
| 1.3.6.1.4.1.25506.2.40.2.2.2.1.4 | Columnhh3cRTSubIfSubIfDesc | read-only | current | The name of the interface |
| 1.3.6.1.4.1.25506.2.40.2.2.2.1.5 | Columnhh3cRTSubIfRowStatus | read-create | current | Operation status. |
| 1.3.6.1.4.1.25506.2.40.2.2.3 | Tablehh3cIfLinkModeTable | not-accessible | current | This table contains objects to get or set the link mode of an interface. According to the layer at which the device processes received data packets, Ethernet i… |
| 1.3.6.1.4.1.25506.2.40.2.2.3.1 | Rowhh3cIfLinkModeEntry | not-accessible | current | The interface link mode table entry |
| 1.3.6.1.4.1.25506.2.40.2.2.3.1.1 | Columnhh3cIfLinkModeIndex | not-accessible | current | The value is the same as ifIndex. |
| 1.3.6.1.4.1.25506.2.40.2.2.3.1.2 | Columnhh3cIfLinkMode | read-write | current | The current link mode of the interface. If hh3cIfLinkModeSwitchSupport is true, writing to the object can change the link mode of the interface. |
| 1.3.6.1.4.1.25506.2.40.2.2.3.1.3 | Columnhh3cIfLinkModeSwitchSupport | read-only | current | Whether the interface supports link mode switching. If this object is true, the interface can operate in either bridge mode or route mode. Otherwise the interf… |
| 1.3.6.1.4.1.25506.2.40.2.2.4 | Tablehh3cIfPortTypeTable | not-accessible | current | This table contains objects to get or set the port type of an interface. |
| 1.3.6.1.4.1.25506.2.40.2.2.4.1 | Rowhh3cIfPortTypeEntry | not-accessible | current | The interface port type table entry. |
| 1.3.6.1.4.1.25506.2.40.2.2.4.1.1 | Columnhh3cIfPortTypeIndex | not-accessible | current | The value is the same as ifIndex. |
| 1.3.6.1.4.1.25506.2.40.2.2.4.1.2 | Columnhh3cIfPortType | read-write | current | The current port type of the interface. Don't set the port type to other for an interface. |
| 1.3.6.1.4.1.25506.2.40.2.2.5 | Tablehh3cIfPfcDot1pTable | not-accessible | current | This table can set the inbound and outbound rate thresholds for the specified dot1p values. |
| 1.3.6.1.4.1.25506.2.40.2.2.5.1 | Rowhh3cIfPfcDot1pEntry | not-accessible | current | Entry items |
| 1.3.6.1.4.1.25506.2.40.2.2.5.1.1 | Columnhh3cIfPfcDot1pValue | read-only | current | The PFC dot1p value list. |
| 1.3.6.1.4.1.25506.2.40.2.2.5.1.2 | Columnhh3cIfPfcDot1pInPps | read-only | current | The current inbound rate for the PFC dot1p. |
| 1.3.6.1.4.1.25506.2.40.2.2.5.1.3 | Columnhh3cIfPfcDot1pOutPps | read-only | current | The current outbound rate for the PFC dot1p. |
| 1.3.6.1.4.1.25506.2.40.2.2.5.1.4 | Columnhh3cIfPfcDot1pInPpsThreshold | read-write | current | The threshold for the inbound rate. If the hh3cIfPfcDot1pInPpsThreshold is set to 0, no hh3cIfPfcInRising will be generated. |
| 1.3.6.1.4.1.25506.2.40.2.2.5.1.5 | Columnhh3cIfPfcDot1pOutPpsThreshold | read-write | current | The threshold for the outbound rate. If the hh3cIfPfcDot1pOutPpsThreshold is set to 0, no hh3cIfPfcOutRising will be generated. |
| 1.3.6.1.4.1.25506.2.40.2.2.6 | Tablehh3cIfQueBufferTable | not-accessible | current | This table contains objects to get the usage info, thresholds, and statistics of queue buffers and to set the thresholds of queue buffers. |
| 1.3.6.1.4.1.25506.2.40.2.2.6.1 | Rowhh3cIfQueBufferEntry | not-accessible | current | Entry items |
| 1.3.6.1.4.1.25506.2.40.2.2.6.1.1 | Columnhh3cIfQueId | read-only | current | The buffer's queue ID. |
| 1.3.6.1.4.1.25506.2.40.2.2.6.1.2 | Columnhh3cIfQueOutUcastTotal | read-only | current | The total amount of outbound unicast queue buffer. |
| 1.3.6.1.4.1.25506.2.40.2.2.6.1.3 | Columnhh3cIfQueOutUcastFree | read-only | current | The amount of free outbound unicast queue buffer. |
| 1.3.6.1.4.1.25506.2.40.2.2.6.1.4 | Columnhh3cIfQueOutUcastUsedRatio | read-only | current | The ratio of outbound unicast queue buffer which is used. |
| 1.3.6.1.4.1.25506.2.40.2.2.6.1.5 | Columnhh3cIfQueOutUcastUsedPeak | read-only | current | The peak of outbound unicast queue buffer which is used. |
| 1.3.6.1.4.1.25506.2.40.2.2.6.1.6 | Columnhh3cIfQueOutUcastThreshold | read-write | current | The alarm threshold of outbound unicast queue buffer which is used. |
| 1.3.6.1.4.1.25506.2.40.2.2.6.1.7 | Columnhh3cIfQueOutUcastOverThres | read-only | current | The number of times of exceeding the alarm threshold of outbound unicast queue buffer which is used. |
| 1.3.6.1.4.1.25506.2.40.2.2.6.1.8 | Columnhh3cIfQueInTotal | read-only | current | The total amount of inbound queue buffer. |
| 1.3.6.1.4.1.25506.2.40.2.2.6.1.9 | Columnhh3cIfQueInFree | read-only | current | The amount of free inbound queue buffer. |
| 1.3.6.1.4.1.25506.2.40.2.2.6.1.10 | Columnhh3cIfQueInUsedRatio | read-only | current | The ratio of inbound queue buffer which is used. |
| 1.3.6.1.4.1.25506.2.40.2.2.6.1.11 | Columnhh3cIfQueInUsedPeak | read-only | current | The peak of inbound queue buffer which is used. |
| 1.3.6.1.4.1.25506.2.40.2.2.6.1.12 | Columnhh3cIfQueInThreshold | read-write | current | The alarm threshold of inbound queue buffer which is used. |
| 1.3.6.1.4.1.25506.2.40.2.2.6.1.13 | Columnhh3cIfQueInOverThres | read-only | current | The number of times over the alarm threshold of inbound queue buffer which is used. |
| 1.3.6.1.4.1.25506.2.40.2.2.6.1.14 | Columnhh3cIfQueInHeadRoomTotal | read-only | current | The total amount of inbound queue headroom buffer. |
| 1.3.6.1.4.1.25506.2.40.2.2.6.1.15 | Columnhh3cIfQueInHeadRoomFree | read-only | current | The amount of free inbound queue headroom buffer. |
| 1.3.6.1.4.1.25506.2.40.2.2.6.1.16 | Columnhh3cIfQueInHeadRoomUsedRatio | read-only | current | The ratio of inbound queue headroom buffer which is used. |
| 1.3.6.1.4.1.25506.2.40.2.2.6.1.17 | Columnhh3cIfQueInHeadRoomUsedPeak | read-only | current | The peak of inbound queue headroom buffer which is used. |
| 1.3.6.1.4.1.25506.2.40.2.3 | Nodehh3cIfInterfaces | |||
| 1.3.6.1.4.1.25506.2.40.2.3.1 | Scalarhh3cIfPhysicalNumber | read-only | current | Represents the number of physical interfaces on the device. |
| 1.3.6.1.4.1.25506.2.40.2.3.2 | Tablehh3cIfTable | not-accessible | current | A list of interface entries. The number of entries is given by the value of IfNumber. |
| 1.3.6.1.4.1.25506.2.40.2.3.2.1 | Rowhh3cIfEntry | not-accessible | current | An entry containing management information applicable to a particular interface. |
| 1.3.6.1.4.1.25506.2.40.2.3.2.1.1 | Columnhh3cIfUpDownTimes | read-only | current | The interface's up/down times, since the device was initialized. |
| 1.3.6.1.4.1.25506.2.40.2.3.2.1.2 | Columnhh3cIfMtu | read-write | current | The size of the largest datagram that can be sent or received on the interface, specified in octets. For interfaces that are used for transmitting network data… |
| 1.3.6.1.4.1.25506.2.40.2.3.2.1.3 | Columnhh3cIfBandwidthRate | read-only | current | The rate of the bandwidth for an interface. |
| 1.3.6.1.4.1.25506.2.40.2.3.2.1.4 | Columnhh3cIfDiscardPktRate | read-only | current | The rate of the discarded packets for an interface. |
| 1.3.6.1.4.1.25506.2.40.2.3.2.1.5 | Columnhh3cIfStatusKeepTime | read-only | current | The time since the interface entered its current operational state. |
| 1.3.6.1.4.1.25506.2.40.2.3.2.1.6 | Columnhh3cIfInNUcastPkts | read-only | current | The number of non-unicast (i.e., subnetwork- broadcast or subnetwork-multicast) packets delivered to a higher-layer protocol. |
| 1.3.6.1.4.1.25506.2.40.2.3.2.1.7 | Columnhh3cIfOutNUcastPkts | read-only | current | The total number of packets that higher-level protocols requested be transmitted to a non- unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) addre… |
| 1.3.6.1.4.1.25506.2.40.2.3.2.1.8 | Columnhh3cIfIsPoe | read-only | current | Whether the interface supports PoE. |
| 1.3.6.1.4.1.25506.2.40.2.3.2.1.9 | Columnhh3cIfOperStatus | read-only | current | Current status of the interface. In testing state, no operational packets can be forwarded. If ifAdminStatus is down, hh3cIfOperStatus should be admindown. If … |
| 1.3.6.1.4.1.25506.2.40.2.3.2.1.10 | Columnhh3cIfDownTimes | read-only | current | Number of times the interface went down, since the device was initialized. |
| 1.3.6.1.4.1.25506.2.40.2.3.2.1.11 | Columnhh3cIfPfcStatus | read-write | current | Pfc (Priority-based Flow Control) status. Forcibly enable Pfc by enable(1). Disable Pfc by disable(2). Set Pfc to auto mode by auto(3). In auto mode, the local… |
| 1.3.6.1.4.1.25506.2.40.2.3.2.1.12 | Columnhh3cIfPfcDot1pNoDrop | read-write | current | Pfc (Priority-based Flow Control) dot1q list, bit 0 through bit 7 corresponding to priority 0 through priority 7. See hh3cIfPfcStatus. |
| 1.3.6.1.4.1.25506.2.40.2.3.2.1.13 | Columnhh3cIfDescription | read-write | current | This object is also an 'alias' name for the interface specified by a network manager, like the object of ifAlias. However, the size of this object is larger th… |
| 1.3.6.1.4.1.25506.2.40.2.3.2.1.14 | Columnhh3cIfFwdErrDiscards | read-only | current | The number of packets that were discarded when being forwarded. |
| 1.3.6.1.4.1.25506.2.40.2.3.2.1.15 | Columnhh3cIfFiberOrCopper | read-only | current | Type of the port,which can be copper or fiber. |
| 1.3.6.1.4.1.25506.2.40.2.3.2.1.16 | Columnhh3cIfTransferMode | read-only | current | Transfer mode of the port, which can be lan or wan. |
| 1.3.6.1.4.1.25506.2.40.2.3.3 | Tablehh3cIfUsingTable | not-accessible | current | A table containing management information applicable to splitting interfaces. To improve port density, reduce costs, and improve network flexibility, a high-ba… |
| 1.3.6.1.4.1.25506.2.40.2.3.3.1 | Rowhh3cIfUsingEntry | not-accessible | current | An entry of hh3cIfUsingTable. |
| 1.3.6.1.4.1.25506.2.40.2.3.3.1.1 | Columnhh3cIfUsingIndex | not-accessible | current | Index of an interface that can be split into multiple low-bandwidth breakout interfaces or be restored to a high-bandwidth interface. |
| 1.3.6.1.4.1.25506.2.40.2.3.3.1.2 | Columnhh3cIfUsingSupportType | read-only | current | This object specifies the port type which can be split into or restored to. From lowest bit, each bit corresponds to a port type ('10GE', '20GE', '40GE', '100G… |
| 1.3.6.1.4.1.25506.2.40.2.3.3.1.3 | Columnhh3cIfUsingType | read-write | current | This object specifies the port type that can be split into or restored to. After this object is set to a non-zero value, the operation returns success in the f… |
| 1.3.6.1.4.1.25506.2.40.2.3.3.1.4 | Columnhh3cIfUsingStatus | read-only | current | After object hh3cIfUsingType is set to a non-zero value, the value for this object is needReboot(1) until you reboot the line card (for distributed devices) or… |
| 1.3.6.1.4.1.25506.2.40.3 | Nodehh3cIfExtTrap | |||
| 1.3.6.1.4.1.25506.2.40.3.0 | Nodehh3cIfExtTrapPrex | |||
| 1.3.6.1.4.1.25506.2.40.3.0.1 | Notificationhh3cIfBandwidthUsageHigh | current | The notification is generated when the rate of the bandwidth for the interface exceeds the upper limit. | |
| 1.3.6.1.4.1.25506.2.40.3.0.2 | Notificationhh3cIfDiscardPktRateHigh | current | The notification is generated when the rate of the discarded packets for the interface exceeds the upper limit. | |
| 1.3.6.1.4.1.25506.2.40.3.0.3 | Notificationhh3cIfDampeningSuppressed | current | The notification is generated when the interface is suppressed via dampening. | |
| 1.3.6.1.4.1.25506.2.40.3.0.4 | Notificationhh3cIfDampeningNotSuppressed | current | The notification is generated when the interface is resumed to not suppressed via dampening. | |
| 1.3.6.1.4.1.25506.2.40.3.0.5 | Notificationhh3cIfPortUp | current | The notification is generated when physical state of the interface changes to up. | |
| 1.3.6.1.4.1.25506.2.40.3.0.6 | Notificationhh3cIfPortDown | current | The notification is generated when physical state of the interface changes to down. | |
| 1.3.6.1.4.1.25506.2.40.3.0.7 | Notificationhh3cIfPfcOutRising | current | The notification is generated when the outbound rate exceeds the threshold for the dot1p value. If the hh3cIfPfcDot1pOutPpsThreshold is set to 0, no hh3cIfPfcO… | |
| 1.3.6.1.4.1.25506.2.40.3.0.8 | Notificationhh3cIfPfcInRising | current | The notification is generated when the inbound rate exceeds the threshold for the dot1p value. If the hh3cIfPfcDot1pInPpsThreshold is set to 0, no hh3cIfPfcInR… | |
| 1.3.6.1.4.1.25506.2.40.3.0.9 | Notificationhh3cIfMappingIfStatusBackup | current | The notification is generated when the mapping status of the interface changes to backup. | |
| 1.3.6.1.4.1.25506.2.40.3.0.10 | Notificationhh3cIfMappingIfStatusNormal | current | The notification is generated when the mapping status of the interface changes to normal. | |
| 1.3.6.1.4.1.25506.2.40.3.0.11 | Notificationhh3cIfPortRateDegrade | current | The notification is generated when the negotiated interface rate decreases. | |
| 1.3.6.1.4.1.25506.2.40.3.0.12 | Notificationhh3cIfPortRateDegradeResume | current | The notification is generated when the negotiated interface rate recovers. | |
| 1.3.6.1.4.1.25506.2.40.3.0.13 | Notificationhh3cIfHalfDuplex | current | The notification is generated when the half duplex mode is autonegotiated for the interface. | |
| 1.3.6.1.4.1.25506.2.40.3.0.14 | Notificationhh3cIfBufferInDiscardAlarm | current | The notification is generated when the number of ingress buffer discard exceeds the upper threshold. | |
| 1.3.6.1.4.1.25506.2.40.3.0.15 | Notificationhh3cIfBufferInDiscardResume | current | The notification is generated when the number of ingress buffer discard from above the upper threshold to below the lower threshold. | |
| 1.3.6.1.4.1.25506.2.40.3.0.16 | Notificationhh3cIfHalfDuplexRising | current | The notification is generated when work mode change to half duplex. | |
| 1.3.6.1.4.1.25506.2.40.3.0.17 | Notificationhh3cIfChangeMultiChassis | current | The notification is generated when centent or distributed expanded to multiple enclosures, and the interface information is changes. | |
| 1.3.6.1.4.1.25506.2.40.3.0.18 | Notificationhh3cIfChangeMultiChassisResume | current | The notification is generated when multiple rolled back to centent or distributed , and the interface information changes. | |
| 1.3.6.1.4.1.25506.2.40.3.0.19 | Notificationhh3cIfCfgRecoverOverSlot | current | The notification is generated when The slot is inserted successfully. | |
| 1.3.6.1.4.1.25506.2.40.3.0.20 | Notificationhh3cIfCfgRecoverOverSubSlot | current | The notification is generated when The subslot is inserted successfully. | |
| 1.3.6.1.4.1.25506.2.40.3.0.21 | Notificationhh3cIfInterfaceDelete | current | The notification is generated when the interface to delete. | |
| 1.3.6.1.4.1.25506.2.40.3.0.22 | Notificationhh3cIfErrordown | current | The notification is generated when the interface error-down occured. | |
| 1.3.6.1.4.1.25506.2.40.3.0.23 | Notificationhh3cIfErrordownRecovery | current | The notification is generated when the interface error-down recover. | |
| 1.3.6.1.4.1.25506.2.40.3.0.24 | Notificationhh3cIfLosAlarm | current | The notification is generated when no power is input. | |
| 1.3.6.1.4.1.25506.2.40.3.0.25 | Notificationhh3cIfLosAlarmResume | current | The notification is generated when the no power input error is removed. | |
| 1.3.6.1.4.1.25506.2.40.3.0.26 | Notificationhh3cIfLofAlarm | current | The notification is generated when an out of frame (OOF) error occurs. | |
| 1.3.6.1.4.1.25506.2.40.3.0.27 | Notificationhh3cIfLofAlarmResume | current | The notification is generated when the OOF error is removed. | |
| 1.3.6.1.4.1.25506.2.40.3.0.28 | Notificationhh3cIfLFaultAlarm | current | The notification is generated when local fault error occurs. | |
| 1.3.6.1.4.1.25506.2.40.3.0.29 | Notificationhh3cIfLFaultAlarmResume | current | The notification is generated when local fault error is removed. | |
| 1.3.6.1.4.1.25506.2.40.3.0.30 | Notificationhh3cIfRFaultAlarm | current | The notification is generated when remote fault error occurs. | |
| 1.3.6.1.4.1.25506.2.40.3.0.31 | Notificationhh3cIfRFaultAlarmResume | current | The notification is generated when remote fault error is removed. | |
| 1.3.6.1.4.1.25506.2.40.3.0.32 | Notificationhh3cIfOofAlarm | current | The notification is generated if a frame header fails to be identified for five times. | |
| 1.3.6.1.4.1.25506.2.40.3.0.33 | Notificationhh3cIfOofAlarmResume | current | The notification is generated when the frame header identification failure is fixed. | |
| 1.3.6.1.4.1.25506.2.40.3.0.34 | Notificationhh3cIfSfbereAlarm | current | The notification is generated when the error-code count exceeds the threshold. | |
| 1.3.6.1.4.1.25506.2.40.3.0.35 | Notificationhh3cIfSfbereAlarmResume | current | The notification is generated when the error-code count drops to the normal range. | |
| 1.3.6.1.4.1.25506.2.40.3.0.36 | Notificationhh3cIfPaisAlarm | current | The notification is generated when error occurs on a high-order path. | |
| 1.3.6.1.4.1.25506.2.40.3.0.37 | Notificationhh3cIfPaisAlarmResume | current | The notification is generated when the error removed from the figh-order path. | |
| 1.3.6.1.4.1.25506.2.40.3.0.38 | Notificationhh3cIfHpJ1TiuAlarm | current | The notification is generated when the J1 byte is not steady. | |
| 1.3.6.1.4.1.25506.2.40.3.0.39 | Notificationhh3cIfHpJ1TiuAlarmResume | current | The notification is generated when the J1 byte recovers from the unsteady condition. | |
| 1.3.6.1.4.1.25506.2.40.3.0.40 | Notificationhh3cIfRroolAlarm | current | The notification is generated when the clock is unlocked. | |
| 1.3.6.1.4.1.25506.2.40.3.0.41 | Notificationhh3cIfRroolAlarmResume | current | The notification is generated when the clock is locket. | |
| 1.3.6.1.4.1.25506.2.40.3.0.42 | Notificationhh3cIfNegoFailedAlarm | current | The notification is generated when the interface auto-negotiation fails. | |
| 1.3.6.1.4.1.25506.2.40.3.0.43 | Notificationhh3cIfNegoFailedAlarmResume | current | The notification is generated when the interface auto-negotiation succeeds | |
| 1.3.6.1.4.1.25506.2.40.3.0.44 | Notificationhh3cIfEthRxFlowFallAlarm | current | The notification is generated when the inbound traffic volume drop below the threshold. | |
| 1.3.6.1.4.1.25506.2.40.3.0.45 | Notificationhh3cIfEthRxFlowFallAlarmResume | current | The notification is generated when the inbound traffic volume traffic volume increases to the normal range. | |
| 1.3.6.1.4.1.25506.2.40.3.0.46 | Notificationhh3cIfEthTxFlowFallAlarm | current | The notification is generated when the outbound traffic volume drops below the threshold. | |
| 1.3.6.1.4.1.25506.2.40.3.0.47 | Notificationhh3cIfEthTxFlowFallAlarmResume | current | The notification is generated when the outbound traffic volume increases to the normal range. | |
| 1.3.6.1.4.1.25506.2.40.3.0.48 | Notificationhh3cIfLoopbackAlarm | current | The notification is generated when the loopback configration is issued. | |
| 1.3.6.1.4.1.25506.2.40.3.0.49 | Notificationhh3cIfLoopbackAlarmResume | current | The notification is generated when the loopback configuration is removed. | |
| 1.3.6.1.4.1.25506.2.40.3.0.50 | Notificationhh3cIfTtlLoop | current | The notification is generated when a TTL timeout alarm occurs. | |
| 1.3.6.1.4.1.25506.2.40.3.0.51 | Notificationhh3cIfTtlLoopResume | current | The notification is generated when TTL timeout alarm is cleared. | |
| 1.3.6.1.4.1.25506.2.40.3.0.52 | Notificationhh3cIfHalfDuplexClear | current | The notification is generated When the working mode changes from half duplex to full duplex. | |
| 1.3.6.1.4.1.25506.2.40.3.0.53 | Notificationhh3cIfEgressDropAlarm | current | The notification is generated when packet loss occurs on a port. | |
| 1.3.6.1.4.1.25506.2.40.3.0.54 | Notificationhh3cIfEgressDropRecover | current | The notification is generated when packet loss recovers on a port. | |
| 1.3.6.1.4.1.25506.2.40.3.0.55 | Notificationhh3cIfBoardEgressDropAlarm | current | The notification is generated when the outgoing unicast traffic of the board is discarded. | |
| 1.3.6.1.4.1.25506.2.40.3.0.56 | Notificationhh3cIfBoardEgressDropRecover | current | The notification is generated when the outgoing unicast traffic of the board is restored. | |
| 1.3.6.1.4.1.25506.2.40.3.0.57 | Notificationhh3cIfComboTypeChange | current | The notification is generated when the combo type changes due to command line configuration. | |
| 1.3.6.1.4.1.25506.2.40.3.0.58 | Notificationhh3cIfIngressAgingDropAlarm | current | The notification is generated when traffic in the slot ingress buffer is discarded for no schedule. | |
| 1.3.6.1.4.1.25506.2.40.3.0.59 | Notificationhh3cIfIngressAgingDropResume | current | The notification is generated when traffic in the slot ingress buffer recovered from discard with no schedule. | |
| 1.3.6.1.4.1.25506.2.40.3.0.60 | Notificationhh3cIfLinkFlapDown | current | The notification is generated when the interface shutdown because the link vibrates frequently. | |
| 1.3.6.1.4.1.25506.2.40.3.0.61 | Notificationhh3cIfMappingIfStatusBlock | current | The notification is generated when the mapping status of the interface changes to block. | |
| 1.3.6.1.4.1.25506.2.40.3.0.62 | Notificationhh3cIfMappingIfStatusLinkageDown | current | The notification is generated when the mapping status of the interface changes to linkagedown. | |
| 1.3.6.1.4.1.25506.2.40.3.0.63 | Notificationhh3cIfFlowControlDLAlarm | current | The notification is generated when the port does not forward messages but receives a large number of pause frames or the port continuously sends a large number… | |
| 1.3.6.1.4.1.25506.2.40.3.0.64 | Notificationhh3cIfFlowControlDLAlarmResume | current | The notification is generated when the port does not forward messages and does not receive a large number of pause frames or the port continuously sends a larg… | |
| 1.3.6.1.4.1.25506.2.40.3.0.65 | Notificationhh3cIfOutputErrorAlarm | current | The notification is generated when some service data on the port is discarded. | |
| 1.3.6.1.4.1.25506.2.40.3.0.66 | Notificationhh3cIfOutputErrorAlarmResume | current | The notification is generated when no service data is dropped on the port. | |
| 1.3.6.1.4.1.25506.2.40.3.0.67 | Notificationhh3cIfCableSnrAbnormal | current | The notification is generated when the working rate of the MultiGE interface is 2.5Gbit/s or above, the network cable quality is poor, or there is signal inter… | |
| 1.3.6.1.4.1.25506.2.40.3.0.68 | Notificationhh3cIfCableSnrNormal | current | The notification is generated when the working rate of the MultiGE interface is 2.5Gbit/s or above, the network cable is intact, or there is no signal interfer… | |
| 1.3.6.1.4.1.25506.2.40.3.0.69 | Notificationhh3cIfCableSnrDetectNotSupport | current | The notification is generated when network cable quality cannot be detected, and the MultiGE interface changes from up to down. | |
| 1.3.6.1.4.1.25506.2.40.3.0.70 | Notificationhh3cIfSfpNotSupportSingleFiber | current | The notification is generated when the optical module inserted in the interface does not support the single fiber function. | |
| 1.3.6.1.4.1.25506.2.40.3.0.71 | Notificationhh3cIfLRMStateAbnormal | current | The notification is generated when the interface does not support the LRM optical module. | |
| 1.3.6.1.4.1.25506.2.40.3.0.72 | Notificationhh3cIfSfpWorkOnlyNonNego | current | The notification is generated when the GE optical module inserted into the XGE interface can only work in the non-self-negotiated 1000Mbit/s mode, and the inte… | |
| 1.3.6.1.4.1.25506.2.40.3.0.73 | Notificationhh3cIfPfcDeadLockAlarm | current | The notification is generated when PFC deadlock may lead to blocked network traffic. | |
| 1.3.6.1.4.1.25506.2.40.3.0.74 | Notificationhh3cIfPfcDeadLockResume | current | The notification is generated when PFC deadlock recovers network traffic. | |
| 1.3.6.1.4.1.25506.2.40.3.0.75 | Notificationhh3cIfPfcTurnOffAlarm | current | The notification is generated when the number of deadlock occurrences in a detection interval exceeds the threshold value of PFC automatic shutdown. | |
| 1.3.6.1.4.1.25506.2.40.3.0.76 | Notificationhh3cIfPfcTurnOffResume | current | The notification is generated when the number of deadlock occurrences in a detection interval drops below the threshold value of PFC automatic shutdown. | |
| 1.3.6.1.4.1.25506.2.40.3.0.77 | Notificationhh3cIfQueueAlarm | current | The notification is generated when the queue depth usage rate of the queue on the interface exceeds the configured value on the interface. | |
| 1.3.6.1.4.1.25506.2.40.3.0.78 | Notificationhh3cIfQueueResume | current | The notification is generated when the queue depth usage rate of the queue on the interface drops below the configured value on the interface. | |
| 1.3.6.1.4.1.25506.2.40.3.0.79 | Notificationhh3cIfQueueStatDiscardAlarm | current | The notification is generated when the number of packets dropped/bytes dropped/packet loss rate in the port queue reaches the alarm threshold. | |
| 1.3.6.1.4.1.25506.2.40.3.0.80 | Notificationhh3cIfQueueStatDiscardResume | current | The notification is generated when the number of packets dropped/bytes dropped/packet loss rate in the port queue drops below the alarm threshold. | |
| 1.3.6.1.4.1.25506.2.40.3.0.81 | Notificationhh3cIfQueueEgressCongestionAlarm | current | The notification is generated when congestion occurs in the outgoing direction of the queue on the interface. | |
| 1.3.6.1.4.1.25506.2.40.3.0.82 | Notificationhh3cIfQueueEgressCongestionClear | current | The notification is generated when the congestion ofin the outgoing direction in the queue on the interface is removed. | |
| 1.3.6.1.4.1.25506.2.40.3.0.83 | Notificationhh3cIfAggPortBwChange | current | The notification is generated when the trunk interface bandwidth changes. | |
| 1.3.6.1.4.1.25506.2.40.3.0.84 | Notificationhh3cIfRateOfTrafficRising | current | The notification is generated when the interface slot flow is greater than the threshold. | |
| 1.3.6.1.4.1.25506.2.40.3.1 | Nodehh3cIfExtTrapObject | |||
| 1.3.6.1.4.1.25506.2.40.3.1.1 | Tablehh3cIfExtTrapCfgTable | not-accessible | current | The trap configuration table. |
| 1.3.6.1.4.1.25506.2.40.3.1.1.1 | Rowhh3cIfExtTrapCfgEntry | not-accessible | current | An entry for this table. |
| 1.3.6.1.4.1.25506.2.40.3.1.1.1.1 | Columnhh3cIfBandwidthUpperLimit | read-write | current | The rate of the bandwidth upper limit for an interface. |
| 1.3.6.1.4.1.25506.2.40.3.1.1.1.2 | Columnhh3cIfDiscardPktRateUpperLimit | read-write | current | The rate of the discarded packets upper limit for an interface. |
| 1.3.6.1.4.1.25506.2.40.4 | Nodehh3cIfMonScalarGroup | |||
| 1.3.6.1.4.1.25506.2.40.5 | Nodehh3cIfMonGroup | |||
| 1.3.6.1.4.1.25506.2.40.5.1 | Nodehh3cIfMonStat | |||
| 1.3.6.1.4.1.25506.2.40.5.1.1 | Tablehh3cIfMonStatTable | not-accessible | current | This table is about some types of statistics. |
| 1.3.6.1.4.1.25506.2.40.5.1.1.1 | Rowhh3cIfMonStatEntry | not-accessible | current | Entry items. |
| 1.3.6.1.4.1.25506.2.40.5.1.1.1.1 | Columnhh3cIfMonInputUsageStatistics | read-only | current | Statistics about the inbound bandwidth usage. |
| 1.3.6.1.4.1.25506.2.40.5.1.1.1.2 | Columnhh3cIfMonOutputUsageStatistics | read-only | current | Statistics about the outbound bandwidth usage. |
| 1.3.6.1.4.1.25506.2.40.5.1.1.1.3 | Columnhh3cIfMonInputErrorAlarmStatistics | read-only | current | Statistics about the number of inbound error packets. |
| 1.3.6.1.4.1.25506.2.40.5.1.1.1.4 | Columnhh3cIfMonOutputErrorAlarmStatistics | read-only | current | Statistics about the number of outbound error packets. |
| 1.3.6.1.4.1.25506.2.40.5.1.1.1.5 | Columnhh3cIfMonSdhErrorStatistics | read-only | current | Statistics about the number of SDH error packets. |
| 1.3.6.1.4.1.25506.2.40.5.1.1.1.6 | Columnhh3cIfMonSdhB1ErrorStatistics | read-only | current | Statistics about the number of SDH B1 error packets. |
| 1.3.6.1.4.1.25506.2.40.5.1.1.1.7 | Columnhh3cIfMonSdhB2ErrorStatistics | read-only | current | Statistics about the number of SDH B2 error packets. |
| 1.3.6.1.4.1.25506.2.40.5.1.1.1.8 | Columnhh3cIfMonCRCErrorStatistics | read-only | current | Statistics about the number of CRC error packets. |
| 1.3.6.1.4.1.25506.2.40.5.1.1.1.9 | Columnhh3cIfMonRxPauseFrameStatistics | read-only | current | Statistics about the number of received pause frames. |
| 1.3.6.1.4.1.25506.2.40.5.1.1.1.10 | Columnhh3cIfMonTxPauseFrameStatistics | read-only | current | Statistics about the number of transmitted pause frames. |
| 1.3.6.1.4.1.25506.2.40.5.1.1.1.11 | Columnhh3cIfMonRuntStatistics | read-only | current | Statistics about the Runt packets. |
| 1.3.6.1.4.1.25506.2.40.5.1.1.1.12 | Columnhh3cIfMonGiantStatistics | read-only | current | Statistics about the Giant packets. |
| 1.3.6.1.4.1.25506.2.40.5.1.1.1.13 | Columnhh3cIfMonInputBufferDropStatistics | read-only | current | Statistics about the input buffer dropped packets. |
| 1.3.6.1.4.1.25506.2.40.5.1.1.1.14 | Columnhh3cIfMonOutputBufferDropStatistics | read-only | current | Statistics about the output buffer dropped packets. |
| 1.3.6.1.4.1.25506.2.40.5.1.1.1.15 | Columnhh3cIfMonJamDiscardStatistics | read-only | current | Statistics of congestion and packet loss. |
| 1.3.6.1.4.1.25506.2.40.5.1.1.1.16 | Columnhh3cIfMonBadBytesStatistics | read-only | current | Bad packet byte statistics. |
| 1.3.6.1.4.1.25506.2.40.5.1.1.1.17 | Columnhh3cIfMonErrorRateStatistics | read-only | current | Statistics of packet error rate. |
| 1.3.6.1.4.1.25506.2.40.5.2 | Nodehh3cIfMonControl | |||
| 1.3.6.1.4.1.25506.2.40.5.2.1 | Tablehh3cIfMonThresholdTable | not-accessible | current | This table is about the upper threshold, lower threshold, CRC type, and inspection interval. The upper threshold and lower threshold must be bound together. If… |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1 | Rowhh3cIfMonThresholdEntry | not-accessible | current | Entry items. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.1 | Columnhh3cIfMonInputUsageLowThres | read-write | current | Lower threshold for the inbound bandwidth usage. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.2 | Columnhh3cIfMonInputUsageHighThres | read-write | current | Upper threshold for the inbound bandwidth usage. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.3 | Columnhh3cIfMonOutputUsageLowThres | read-write | current | Lower threshold for the outbound bandwidth usage. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.4 | Columnhh3cIfMonOutputUsageHighThres | read-write | current | Upper threshold for the outbound bandwidth usage. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.5 | Columnhh3cIfMonInputErrorAlarmLowThres | read-write | current | Lower threshold for the number of inbound error packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.6 | Columnhh3cIfMonInputErrorAlarmHighThres | read-write | current | Upper threshold for the number of inbound error packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.7 | Columnhh3cIfMonInputErrorAlarmInterval | read-write | current | Inspection interval for the number of inbound error packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.8 | Columnhh3cIfMonOutputErrorAlarmLowThres | read-write | current | Lower threshold for the number of outbound error packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.9 | Columnhh3cIfMonOutputErrorAlarmHighThres | read-write | current | Upper threshold for the number of outbound error packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.10 | Columnhh3cIfMonOutputErrorAlarmInterval | read-write | current | Inspection interval for the number of outbound error packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.11 | Columnhh3cIfMonSdhErrorLowThres | read-write | current | Lower threshold for the number of SDH error packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.12 | Columnhh3cIfMonSdhErrorHighThres | read-write | current | Upper threshold for the number of SDH error packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.13 | Columnhh3cIfMonSdhErrorInterval | read-write | current | Inspection interval for the number of SDH error packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.14 | Columnhh3cIfMonSdhB1ErrorLowThres | read-write | current | Lower threshold for the number of SDH B1 error packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.15 | Columnhh3cIfMonSdhB1ErrorHighThres | read-write | current | Upper threshold for the number of SDH B1 error packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.16 | Columnhh3cIfMonSdhB1ErrorInterval | read-write | current | Inspection interval for the number of SDH B1 error packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.17 | Columnhh3cIfMonSdhB2ErrorLowThres | read-write | current | Lower threshold for the number of SDH B2 error packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.18 | Columnhh3cIfMonSdhB2ErrorHighThres | read-write | current | Upper threshold for the number of SDH B2 error packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.19 | Columnhh3cIfMonSdhB2ErrorInterval | read-write | current | Inspection interval for the number of SDH B2 error packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.20 | Columnhh3cIfMonCRCErrorLowThres | read-write | current | Lower threshold for the number of CRC error packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.21 | Columnhh3cIfMonCRCErrorHighThres | read-write | current | Upper threshold for the number of CRC error packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.22 | Columnhh3cIfMonCRCErrorInterval | read-write | current | Inspection interval for the number of CRC error packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.23 | Columnhh3cIfMonCRCErrType | read-write | current | Inspection type for the CRC error packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.24 | Columnhh3cIfMonRxPauseFrameLowThres | read-write | current | Lower threshold for the number of received pause frames. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.25 | Columnhh3cIfMonRxPauseFrameHighThres | read-write | current | Upper threshold for the number of received pause frames. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.26 | Columnhh3cIfMonRxPauseFrameInterval | read-write | current | Inspection interval for the number of received pause frames. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.27 | Columnhh3cIfMonTxPauseFrameLowThres | read-write | current | Lower threshold for the number of transmitted pause frames. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.28 | Columnhh3cIfMonTxPauseFrameHighThres | read-write | current | Upper threshold for the number of transmitted pause frames. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.29 | Columnhh3cIfMonTxPauseFrameInterval | read-write | current | Inspection interval for the number of transmitted pause frames. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.30 | Columnhh3cIfMonGiantLowThres | read-write | current | Lower threshold for the number of Giant error packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.31 | Columnhh3cIfMonGiantHighThres | read-write | current | Upper threshold for the number of Giant error packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.32 | Columnhh3cIfMonGiantInterval | read-write | current | Inspection interval for the number of Giant error packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.33 | Columnhh3cIfMonRuntLowThres | read-write | current | Lower threshold for the number of Runt error packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.34 | Columnhh3cIfMonRuntHighThres | read-write | current | Upper threshold for the number of Runt error packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.35 | Columnhh3cIfMonRuntInterval | read-write | current | Inspection interval for the number of Runt packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.36 | Columnhh3cIfMonInputBufferDropLowThres | read-write | current | Lower threshold for the number of input buffer dropped packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.37 | Columnhh3cIfMonInputBufferDropHighThres | read-write | current | Upper threshold for the number of input buffer dropped packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.38 | Columnhh3cIfMonInputBufferDropInterval | read-write | current | Inspection interval for the number of input buffer dropped packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.39 | Columnhh3cIfMonOutputBufferDropLowThres | read-write | current | Lower threshold for the number of output buffer dropped packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.40 | Columnhh3cIfMonOutputBufferDropHighThres | read-write | current | Upper threshold for the number of output buffer dropped packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.41 | Columnhh3cIfMonOutputBufferDropInterval | read-write | current | Inspection interval for the number of output buffer dropped packets. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.42 | Columnhh3cIfMonJamDiscardThres | read-write | current | Congestion packet loss threshold. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.43 | Columnhh3cIfMonJamDiscardInterval | read-write | current | Time interval for counting congestion and packet loss. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.44 | Columnhh3cIfMonBadBytesThres | read-write | current | Bad packet byte threshold. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.45 | Columnhh3cIfMonBadBytesDiscardInterval | read-write | current | Time interval for counting bad packet bytes. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.46 | Columnhh3cIfMonErrorRateThres | read-write | current | Packet error rate threshold. |
| 1.3.6.1.4.1.25506.2.40.5.2.1.1.47 | Columnhh3cIfMonErrorRateDiscardInterval | read-write | current | Time interval for statistics of packet error rate. |
| 1.3.6.1.4.1.25506.2.40.5.2.2 | Tablehh3cIfMonAlarmDownEnableTable | not-accessible | current | This table can set or get whether to enable the interface down function. |
| 1.3.6.1.4.1.25506.2.40.5.2.2.1 | Rowhh3cIfMonAlarmDownEnableEntry | not-accessible | current | Entry items |
| 1.3.6.1.4.1.25506.2.40.5.2.2.1.1 | Columnhh3cIfMonInputErrorAlarmEnableDown | read-write | current | When the number of inbound error packets exceeds the upper threshold, the physical interface goes down. |
| 1.3.6.1.4.1.25506.2.40.5.2.2.1.2 | Columnhh3cIfMonOutputErrorAlarmEnableDown | read-write | current | When the number of outbound error packets exceeds the upper threshold, the physical interface goes down. |
| 1.3.6.1.4.1.25506.2.40.5.2.2.1.3 | Columnhh3cIfMonSdhErrorEnableDown | read-write | current | When the number of SDH error packets exceeds the upper threshold, the physical interface goes down. |
| 1.3.6.1.4.1.25506.2.40.5.2.2.1.4 | Columnhh3cIfMonSdhB1ErrorEnableDown | read-write | current | When the number of SDH B1 error packets exceeds the upper threshold, the physical interface goes down. |
| 1.3.6.1.4.1.25506.2.40.5.2.2.1.5 | Columnhh3cIfMonSdhB2ErrorEnableDown | read-write | current | When the number of SDH B2 error packets exceeds the upper threshold, the physical interface goes down. |
| 1.3.6.1.4.1.25506.2.40.5.2.2.1.6 | Columnhh3cIfMonCRCErrorEnableDown | read-write | current | When the number of CRC error packets exceeds the upper threshold, the physical interface goes down. |
| 1.3.6.1.4.1.25506.2.40.5.2.2.1.7 | Columnhh3cIfMonGiantEnableDown | read-write | current | When the number of Giant error packets exceeds the upper threshold, the physical interface goes down. |
| 1.3.6.1.4.1.25506.2.40.5.2.2.1.8 | Columnhh3cIfMonRuntEnableDown | read-write | current | When the number of Runt error packets exceeds the upper threshold, the physical interface goes down. |
| 1.3.6.1.4.1.25506.2.40.5.2.2.1.9 | Columnhh3cIfMonTxPauseFrameEnableDown | read-write | current | When the number of transmitted pause frames exceeds the upper threshold, the physical interface goes down. |
| 1.3.6.1.4.1.25506.2.40.5.2.2.1.10 | Columnhh3cIfMonInputBufferDropEnableDown | read-write | current | When the number of input buffer dropped packets exceeds the upper threshold, the physical interface goes down. |
| 1.3.6.1.4.1.25506.2.40.5.2.2.1.11 | Columnhh3cIfMonOutputBufferDropEnableDown | read-write | current | When the number of output buffer dropped packets exceeds the upper threshold, the physical interface goes down. |
| 1.3.6.1.4.1.25506.2.40.6 | Nodehh3cIfMonTrap | |||
| 1.3.6.1.4.1.25506.2.40.6.0 | Nodehh3cIfMonTrapPrex | |||
| 1.3.6.1.4.1.25506.2.40.6.0.1 | Notificationhh3cIfMonInputUsageRising | current | The notification is generated when the inbound bandwidth usage exceeds the upper threshold. | |
| 1.3.6.1.4.1.25506.2.40.6.0.2 | Notificationhh3cIfMonInputUsageResume | current | The notification is generated when the inbound bandwidth usage drops from above the upper threshold to below the lower threshold. | |
| 1.3.6.1.4.1.25506.2.40.6.0.3 | Notificationhh3cIfMonOutputUsageRising | current | The notification is generated when the outbound bandwidth usage exceeds the upper threshold. | |
| 1.3.6.1.4.1.25506.2.40.6.0.4 | Notificationhh3cIfMonOutputUsageResume | current | The notification is generated when the outbound bandwidth usage drops from above the upper threshold to below the lower threshold. | |
| 1.3.6.1.4.1.25506.2.40.6.0.5 | Notificationhh3cIfMonInputErrorAlarmRising | current | The notification is generated when the number of inbound error packets exceeds the upper threshold within the default interval. | |
| 1.3.6.1.4.1.25506.2.40.6.0.6 | Notificationhh3cIfMonInputErrorAlarmResume | current | The notification is generated when the number of inbound error packets drops from above the upper threshold to below the lower threshold within the default int… | |
| 1.3.6.1.4.1.25506.2.40.6.0.7 | Notificationhh3cIfMonOutputErrorAlarmRising | current | The notification is generated when the number of outbound error packets exceeds the upper threshold within the default interval. | |
| 1.3.6.1.4.1.25506.2.40.6.0.8 | Notificationhh3cIfMonOutputErrorAlarmResume | current | The notification is generated when the number of outbound error packets drops from above the upper threshold to below the lower threshold within the default in… | |
| 1.3.6.1.4.1.25506.2.40.6.0.9 | Notificationhh3cIfMonSdhErrorRising | current | The notification is generated when the number of SDH error packets exceeds the upper threshold within the default interval. | |
| 1.3.6.1.4.1.25506.2.40.6.0.10 | Notificationhh3cIfMonSdhErrorResume | current | The notification is generated when the number of SDH error packets drops from above the upper threshold to below the lower threshold within the default interva… | |
| 1.3.6.1.4.1.25506.2.40.6.0.11 | Notificationhh3cIfMonSdhB1ErrorRising | current | The notification is generated when the number of SDH B1 error packets exceeds the upper threshold within the default interval. | |
| 1.3.6.1.4.1.25506.2.40.6.0.12 | Notificationhh3cIfMonSdhB1ErrorResume | current | The notification is generated when the number of SDH B1 error packets drops from above the upper threshold to below the lower threshold within the default inte… | |
| 1.3.6.1.4.1.25506.2.40.6.0.13 | Notificationhh3cIfMonSdhB2ErrorRising | current | The notification is generated when the number of SDH B2 error packets exceeds the upper threshold within the default interval. | |
| 1.3.6.1.4.1.25506.2.40.6.0.14 | Notificationhh3cIfMonSdhB2ErrorResume | current | The notification is generated when the number of SDH B2 error packets drops from above the upper threshold to below the lower threshold within the default inte… | |
| 1.3.6.1.4.1.25506.2.40.6.0.15 | Notificationhh3cIfMonCRCErrorRising | current | The notification is generated when the number of CRC error packets exceeds the upper threshold within the default interval. | |
| 1.3.6.1.4.1.25506.2.40.6.0.16 | Notificationhh3cIfMonCRCErrorResume | current | The notification is generated when the number of CRC error packets drops from above the upper threshold to below the lower threshold within the default interva… | |
| 1.3.6.1.4.1.25506.2.40.6.0.17 | Notificationhh3cIfMonRxPauseFrameRising | current | The notification is generated when the number of received pause frames exceeds the upper threshold. | |
| 1.3.6.1.4.1.25506.2.40.6.0.18 | Notificationhh3cIfMonRxPauseFrameResume | current | The notification is generated when the number of received pause frames drops from above the upper threshold to below the lower-threshold. | |
| 1.3.6.1.4.1.25506.2.40.6.0.19 | Notificationhh3cIfMonTxPauseFrameRising | current | The notification is generated when the number of transmitted pause frames exceeds the upper threshold. | |
| 1.3.6.1.4.1.25506.2.40.6.0.20 | Notificationhh3cIfMonTxPauseFrameResume | current | The notification is generated when the number of transmitted pause frames drops from above the upper threshold to below the lower threshold. | |
| 1.3.6.1.4.1.25506.2.40.6.0.21 | Notificationhh3cIfMonGiantRising | current | The notification is generated when the number of Giant error packets exceeds the upper threshold within the default interval. | |
| 1.3.6.1.4.1.25506.2.40.6.0.22 | Notificationhh3cIfMonGiantResume | current | The notification is generated when the number of Giant error packets drops from above the upper threshold to below the lower threshold within the default inter… | |
| 1.3.6.1.4.1.25506.2.40.6.0.23 | Notificationhh3cIfMonRuntRising | current | The notification is generated when the number of Runt error packets exceeds the upper threshold within the default interval. | |
| 1.3.6.1.4.1.25506.2.40.6.0.24 | Notificationhh3cIfMonRuntResume | current | The notification is generated when the number of Runt error packets drops from above the upper threshold to below the lower threshold within the default interv… | |
| 1.3.6.1.4.1.25506.2.40.6.0.25 | Notificationhh3cIfMonInputBufferDropRising | current | The notification is generated when the number of input buffer dropped packets exceeds the upper threshold within the default interval. | |
| 1.3.6.1.4.1.25506.2.40.6.0.26 | Notificationhh3cIfMonInputBufferDropResume | current | The notification is generated when the number of input buffer dropped packets drops from above the upper threshold to below the lower threshold within the defa… | |
| 1.3.6.1.4.1.25506.2.40.6.0.27 | Notificationhh3cIfMonOutputBufferDropRising | current | The notification is generated when the number of output buffer dropped packets exceeds the upper threshold within the default interval. | |
| 1.3.6.1.4.1.25506.2.40.6.0.28 | Notificationhh3cIfMonOutputBufferDropResume | current | The notification is generated when the number of output buffer dropped packets drops from above the upper threshold to below the lower threshold within the def… | |
| 1.3.6.1.4.1.25506.2.40.6.0.29 | Notificationhh3cIfMonInputUFlowRising | current | The notification is generated when the unknown unicast traffic percentage exceeds the threshold. | |
| 1.3.6.1.4.1.25506.2.40.6.0.30 | Notificationhh3cIfMonInputUFlowFalling | current | The notification is generated when the unknown unicast traffic percentage drops to the normal range within the default interval. | |
| 1.3.6.1.4.1.25506.2.40.6.0.31 | Notificationhh3cIfMonBip8SdError | current | The notification is generated when the error code count exceeds the threshold. | |
| 1.3.6.1.4.1.25506.2.40.6.0.32 | Notificationhh3cIfMonBip8SdErrorResume | current | The notification is generated when the error code count drops to the normal range within the default interval. | |
| 1.3.6.1.4.1.25506.2.40.6.0.33 | Notificationhh3cIfMonCRCBitErrorRising | current | The notification is generated when the CRC bit error ratio exceeds the upper threshold. | |
| 1.3.6.1.4.1.25506.2.40.6.0.34 | Notificationhh3cIfMonCRCBitErrorResume | current | The notification is generated when the CRC bit error ratio drops from above the upper threshold to below the lower threshold. | |
| 1.3.6.1.4.1.25506.2.40.6.0.35 | Notificationhh3cIfMonInputJamDiscardAlarm | current | The notification is generated when the number of incoming packets lost due to network congestion of the interface exceeds the threshold. | |
| 1.3.6.1.4.1.25506.2.40.6.0.36 | Notificationhh3cIfMonInputJamDiscardResume | current | The notification is generated when the number of incoming packets lost due to network congestion of the interface drops below the threshold. | |
| 1.3.6.1.4.1.25506.2.40.6.0.37 | Notificationhh3cIfMonOutputJamDiscardAlarm | current | The notification is generated when the number of outgoing packets lost due to network congestion of the interface exceeds the threshold. | |
| 1.3.6.1.4.1.25506.2.40.6.0.38 | Notificationhh3cIfMonOutputJamDiscardResume | current | The notification is generated when the number of outgoing packets lost due to network congestion of the interface drops below the threshold. | |
| 1.3.6.1.4.1.25506.2.40.6.0.39 | Notificationhh3cIfMonPktDropRateRising | current | The notification is generated when the number of messages discarded on the interface board exceeds the configured alarm threshold. | |
| 1.3.6.1.4.1.25506.2.40.6.0.40 | Notificationhh3cIfMonPktDropRateRecover | current | The notification is generated when the number of discarded messages on the interface board drops below the configured alarm threshold. | |
| 1.3.6.1.4.1.25506.2.40.6.0.41 | Notificationhh3cIfMonBadBytesErrorRising | current | The notification is generated when the number of bad packet bytes exceeds the set alarm threshold. | |
| 1.3.6.1.4.1.25506.2.40.6.0.42 | Notificationhh3cIfMonBadBytesErrorResume | current | The notification is generated when the number of bad packet bytes drops below the set alarm threshold. | |
| 1.3.6.1.4.1.25506.2.40.6.0.43 | Notificationhh3cIfMonPortCrcRateExceed | current | The notification is generated when the CRC packet error rate is greater than or equal to 1000 / s. | |
| 1.3.6.1.4.1.25506.2.40.6.0.44 | Notificationhh3cIfMonPortErrorRateExceed | current | The notification is generated when the average rate of CRC errors, giants and runts exceeded 1000 / s. | |
| 1.3.6.1.4.1.25506.2.40.6.0.45 | Notificationhh3cIfMonInBCRapidChange | current | The notification is generated when the incoming broadcast traffic of the interface suddenly exceeds the threshold. | |
| 1.3.6.1.4.1.25506.2.40.6.0.46 | Notificationhh3cIfMonInBCRapidRecover | current | The notification is generated when the incoming broadcast traffic of the interface suddenly drops below the threshold. | |
| 1.3.6.1.4.1.25506.2.40.6.0.47 | Notificationhh3cIfMonPortCrcRateExceedResume | current | The notification is generated when the CRC packet error rate is less than 1000 / s. | |
| 1.3.6.1.4.1.25506.2.40.6.1 | Nodehh3cIfMonTrapObject | |||
| 1.3.6.1.4.1.25506.2.40.6.1.1 | Scalarhh3cIfMonCRCBitErrorHighThresStr | accessible-for-notify | current | Upper threshold for the CRC bit error ratio |
| 1.3.6.1.4.1.25506.2.40.6.1.2 | Scalarhh3cIfMonCRCBitErrorLowThresStr | accessible-for-notify | current | Lower threshold for the CRC bit error ratio |
| 1.3.6.1.4.1.25506.2.40.6.1.3 | Scalarhh3cIfMonCRCBitErrorRatioStr | accessible-for-notify | current | Statistics about the CRC bit error ratio |