HH3C-PBR-MIB
74 objects
This MIB contains objects to manage the configuration and information of PBR. It routes IP packets by user defined policy other than normal destination address based routing.
Imported Objects
| HH3C-OID-MIB | hh3cCommon |
| IF-MIB | ifIndex |
| INET-ADDRESS-MIB | InetAddress InetAddressType |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE |
| SNMPv2-TC | DisplayString RowStatus TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.25506.2.113 | Identityhh3cPBR | This MIB contains objects to manage the configuration and information of PBR. It routes IP packets by user defined policy other than normal destination address… | ||
| 1.3.6.1.4.1.25506.2.113.1 | Nodehh3cPBRObjects | |||
| 1.3.6.1.4.1.25506.2.113.1.1 | Nodehh3cPBRGlobal | |||
| 1.3.6.1.4.1.25506.2.113.1.1.1 | Scalarhh3cPBRNexthopTrapEnabled | read-write | current | The value is a global setting only for IPv4 PBR. If the value is set to 'false', the feature is disabled. |
| 1.3.6.1.4.1.25506.2.113.1.1.2 | Scalarhh3cPBRLocalPolicy | read-write | current | The value is a global setting. An existing policy name setting enables local PBR for IPv4 packets initiated by the device. Only one policy can be applied local… |
| 1.3.6.1.4.1.25506.2.113.1.1.3 | Scalarhh3cPBRIPv6NexthopTrapEnabled | read-write | current | The value is a global setting only for IPv6 PBR. If the value is set to 'false', the feature is disabled. |
| 1.3.6.1.4.1.25506.2.113.1.2 | Nodehh3cPBRMibTrap | |||
| 1.3.6.1.4.1.25506.2.113.1.2.1 | Nodehh3cPBRTrapObjects | |||
| 1.3.6.1.4.1.25506.2.113.1.2.1.1 | Scalarhh3cPBRNexthopAddrType | accessible-for-notify | current | Indicating address type of hh3cPBRNexthopAddr, which can be IPv4 or IPv6. |
| 1.3.6.1.4.1.25506.2.113.1.2.1.2 | Scalarhh3cPBRNexthopAddr | accessible-for-notify | current | The involved next hop IP address of trap information. |
| 1.3.6.1.4.1.25506.2.113.1.2.2 | Nodehh3cPBRTraps | |||
| 1.3.6.1.4.1.25506.2.113.1.2.2.0 | Nodehh3cPBRTrapsPrefix | |||
| 1.3.6.1.4.1.25506.2.113.1.2.2.0.1 | Notificationhh3cPBRNexthopFailedTrap | current | When the next hop of PBR apply clause became unreachable according to routing information, trap is generated and is sent to the remote monitoring device. | |
| 1.3.6.1.4.1.25506.2.113.2 | Nodehh3cPBRTables | |||
| 1.3.6.1.4.1.25506.2.113.2.1 | Tablehh3cPBRMibPolicyNodeTable | not-accessible | current | A table for PBR nodes. |
| 1.3.6.1.4.1.25506.2.113.2.1.1 | Rowhh3cPBRMibPolicyNodeEntry | not-accessible | current | An entry for PBR nodes. |
| 1.3.6.1.4.1.25506.2.113.2.1.1.1 | Columnhh3cPBRMibPolicyNodeAddrType | not-accessible | current | Address type of policy node, which can be IPv4 or IPv6, Dual-stack. |
| 1.3.6.1.4.1.25506.2.113.2.1.1.2 | Columnhh3cPBRMibPolicyName | not-accessible | current | Policy name of PBR node. |
| 1.3.6.1.4.1.25506.2.113.2.1.1.3 | Columnhh3cPBRMibPolicyNodeId | not-accessible | current | Sequence identifier of PBR node. |
| 1.3.6.1.4.1.25506.2.113.2.1.1.4 | Columnhh3cPBRMibPolicyNodeMode | read-create | current | Mode of PBR node. If the mode of a node is marked as true, the packets that meet the matching rules are processed by action rules in the node. If the mode of a… |
| 1.3.6.1.4.1.25506.2.113.2.1.1.5 | Columnhh3cPBRMibPolicyNodeRowStatus | read-create | current | Operation status of this table entry. Three actions are used: active, createAndGo, and destroy. |
| 1.3.6.1.4.1.25506.2.113.2.1.1.6 | Columnhh3cPBRMibMinPktLen | read-write | current | Specifies the minimum IP packet length in the range of 1 and 65535. Value 0 indicates that this rule is not set. |
| 1.3.6.1.4.1.25506.2.113.2.1.1.7 | Columnhh3cPBRMibMaxPktLen | read-write | current | Specifies the maximum IP packet length in the range of 1 and 65535. The maximum length must be no less than the minimum length. The maximum and the minimum len… |
| 1.3.6.1.4.1.25506.2.113.2.1.1.8 | Columnhh3cPBRMibQosId | read-write | current | Specifies a local Quality of Service(QoS) ID in the range of 1 and 4095. Value 0 indicates that this rule is not set. |
| 1.3.6.1.4.1.25506.2.113.2.1.1.9 | Columnhh3cPBRMibQosIdMode | read-write | current | The mode of the QoS Local ID. The default value is normal. |
| 1.3.6.1.4.1.25506.2.113.2.1.1.10 | Columnhh3cPBRMibVxlanId | read-write | current | Specifies a VXLAN ID in the range of 0 to 16777215. Value -1 indicates that this rule is not set. |
| 1.3.6.1.4.1.25506.2.113.2.1.1.11 | Columnhh3cPBRMibDescription | read-write | current | A description for a policy node. |
| 1.3.6.1.4.1.25506.2.113.2.1.1.12 | Columnhh3cPBRMibApplyContinue | read-write | current | Use apply continue to compare packets with the next policy node upon failure on the current node. Value FALSE indicates that this action is not set. |
| 1.3.6.1.4.1.25506.2.113.2.1.1.13 | Columnhh3cPBRMibApplyFailDropNextHop | read-write | current | Configure the policy node to drop matching packets when the next hop is invalid. If no next hops are specified on the policy node, this command drops all packe… |
| 1.3.6.1.4.1.25506.2.113.2.1.1.14 | Columnhh3cPBRMibApplyIpDf | read-write | current | Sets the Don't Fragment(DF) bit in the IP header of matching packets. The value can be 0 or 1. Value -1 indicates that this action is not set. |
| 1.3.6.1.4.1.25506.2.113.2.1.1.15 | Columnhh3cPBRMibApplyLoadShareNextHop | read-write | current | Enables load sharing among multiple next hops. Value FALSE indicates that this action is not set. |
| 1.3.6.1.4.1.25506.2.113.2.1.1.16 | Columnhh3cPBRMibApplyLoadShareOutIf | read-write | current | Enables load sharing among multiple output interfaces. Value FALSE indicates that this action is not set. |
| 1.3.6.1.4.1.25506.2.113.2.1.1.17 | Columnhh3cPBRMibApplyLSDefaultNextHop | read-write | current | Enables load sharing among multiple default next hops. Value FALSE indicates that this action is not set. |
| 1.3.6.1.4.1.25506.2.113.2.1.1.18 | Columnhh3cPBRMibApplyLSDefaultOutIf | read-write | current | Enables load sharing among multiple default output interfaces. Value FALSE indicates that this action is not set. |
| 1.3.6.1.4.1.25506.2.113.2.1.1.19 | Columnhh3cPBRMibApplyStatisticsValue | read-write | current | Use apply statistics to enable match counting on a policy node. Value FALSE indicates that this action is not set. |
| 1.3.6.1.4.1.25506.2.113.2.2 | Tablehh3cPBRMibIfPolicyTable | not-accessible | current | A table for interfaces being applied with PBR nodes with the same policy name. |
| 1.3.6.1.4.1.25506.2.113.2.2.1 | Rowhh3cPBRMibIfPolicyEntry | not-accessible | current | An entry for reference relation between interface and policy nodes. |
| 1.3.6.1.4.1.25506.2.113.2.2.1.1 | Columnhh3cPBRMibPolicyAddressType | not-accessible | current | Address type of policy node, which can be IPv4 or IPv6, Dual-stack. |
| 1.3.6.1.4.1.25506.2.113.2.2.1.2 | Columnhh3cPBRMibAppliedPolicyName | read-create | current | Policy name of PBR nodes. |
| 1.3.6.1.4.1.25506.2.113.2.2.1.3 | Columnhh3cPBRMibIfPolicyRowStatus | read-create | current | Operation status of this table entry. Three actions are used: active, createAndGo, and destroy. |
| 1.3.6.1.4.1.25506.2.113.2.2.1.4 | Columnhh3cPBRMibIfPolicyShareMode | read-create | current | Applies the policy in resource sharing mode. In this mode, all interfaces on an interface card with the same policy applied share one hardware resource. |
| 1.3.6.1.4.1.25506.2.113.2.3 | Tablehh3cPBRMibMatchAclTable | not-accessible | current | A table for ACLs being used by a policy node. Only one ACL can be used within a node at most. |
| 1.3.6.1.4.1.25506.2.113.2.3.1 | Rowhh3cPBRMibMatchAclEntry | not-accessible | current | An entry for policy node that uses an ACL group as its if-match rule. |
| 1.3.6.1.4.1.25506.2.113.2.3.1.1 | Columnhh3cPBRMibAclGroupId | read-write | current | Index of number-acl group. Setting -1 indicates closing this rule. When ACLName is configured with a valid value, value -1 will be returned for ACLNumber. |
| 1.3.6.1.4.1.25506.2.113.2.3.1.2 | Columnhh3cPBRMibAclGroupName | read-write | current | ACL match criterion by name. The ACL name must start with letter a to z or A to Z. The ACL name cannot be all in any combination of upper-case and lower-case l… |
| 1.3.6.1.4.1.25506.2.113.2.3.1.3 | Columnhh3cPBRMibAclGroupVersion | read-write | current | The type of the ACL. The hh3cPBRMibAclGroupVersion can only be configured when the policy node type is Dual-stack, and cannot be empty. |
| 1.3.6.1.4.1.25506.2.113.2.4 | Tablehh3cPBRMibApplyPrecedenceTable | not-accessible | current | A table for precedence values being used by a policy node. Only one precedence value can be used within a node at most. |
| 1.3.6.1.4.1.25506.2.113.2.4.1 | Rowhh3cPBRMibApplyPrecedenceEntry | not-accessible | current | An entry for policy node with an action to set IP precedence for matching packets. |
| 1.3.6.1.4.1.25506.2.113.2.4.1.1 | Columnhh3cPBRMibApplyPrecedenceValue | read-write | current | Value of precedence being applied on IP header. <0-7> Value of precedence routine Specify routine precedence(0) priority Specify priority precedence(1) immedia… |
| 1.3.6.1.4.1.25506.2.113.2.5 | Tablehh3cPBRMibApplyNexthopTable | not-accessible | current | A table for next hop actions being used by a policy node. |
| 1.3.6.1.4.1.25506.2.113.2.5.1 | Rowhh3cPBRMibApplyNexthopEntry | not-accessible | current | An entry for policy node with an action to set next hop for matching packets. |
| 1.3.6.1.4.1.25506.2.113.2.5.1.1 | Columnhh3cPBRMibApplyNexthopIndex | not-accessible | current | Index of next hop for the apply next hop action. |
| 1.3.6.1.4.1.25506.2.113.2.5.1.2 | Columnhh3cPBRMibApplyNexthopVpnName | read-create | current | Name of VPN instance where apply next hop action is used. |
| 1.3.6.1.4.1.25506.2.113.2.5.1.3 | Columnhh3cPBRMibApplyNexthopAddressType | read-create | current | Address type of hh3cPBRMibApplyNexthopAddress, which can be IPv4 or IPv6. |
| 1.3.6.1.4.1.25506.2.113.2.5.1.4 | Columnhh3cPBRMibApplyNexthopAddress | read-create | current | Next hop IP address of apply next hop action. |
| 1.3.6.1.4.1.25506.2.113.2.5.1.5 | Columnhh3cPBRMibApplyNexthopTrackId | read-create | current | Identifier of track object related with next hop. Specifies a track entry by its number in the range of 1 to 1024. Setting 0 indicates closing this function. |
| 1.3.6.1.4.1.25506.2.113.2.5.1.6 | Columnhh3cPBRMibApplyNexthopDirect | read-create | current | Direct route attribute of next hop according to route information. |
| 1.3.6.1.4.1.25506.2.113.2.5.1.7 | Columnhh3cPBRMibApplyNexthopRowStatus | read-create | current | Operation status of this table entry. Three actions are used: active, createAndGo, and destroy. |
| 1.3.6.1.4.1.25506.2.113.2.5.1.8 | Columnhh3cPBRMibApplyNexthopInboundVpn | read-create | current | Specifies the VPN instance where the inbound interface belongs. If the value is set to TRUE, the VPN instance name will be ignored. |
| 1.3.6.1.4.1.25506.2.113.2.5.1.9 | Columnhh3cPBRMibApplyNexthopWeight | read-create | current | Specifies a load sharing weight in the range of 1 and 100 for the next hop. |
| 1.3.6.1.4.1.25506.2.113.2.5.1.10 | Columnhh3cPBRMibApplyNexthopPathId | read-create | current | Specifies a service chain by its path ID in the range of 1 and 16777215. |
| 1.3.6.1.4.1.25506.2.113.2.5.1.11 | Columnhh3cPBRMibApplyNexthopPathIndex | read-create | current | Specifies a node in the service chain as a next hop by its index in the range of 1 and 255. |
| 1.3.6.1.4.1.25506.2.113.2.6 | Tablehh3cPBRMibApplyDefaultNexthopTable | not-accessible | current | A table for default next hop actions being used by a policy node. |
| 1.3.6.1.4.1.25506.2.113.2.6.1 | Rowhh3cPBRMibApplyDefaultNexthopEntry | not-accessible | current | An entry for policy node with an action to set default next hop for matching packets. |
| 1.3.6.1.4.1.25506.2.113.2.6.1.1 | Columnhh3cPBRMibApplyDefaultNexthopIndex | not-accessible | current | Index of default next hop for the apply default next hop action. |
| 1.3.6.1.4.1.25506.2.113.2.6.1.2 | Columnhh3cPBRMibApplyDefaultNexthopVpnName | read-create | current | Name of VPN instance where apply default next hop action is used. |
| 1.3.6.1.4.1.25506.2.113.2.6.1.3 | Columnhh3cPBRMibApplyDefaultNexthopAddressType | read-create | current | Address type of hh3cPBRMibApplyDefaultNexthopAddress, which can be IPv4 or IPv6. |
| 1.3.6.1.4.1.25506.2.113.2.6.1.4 | Columnhh3cPBRMibApplyDefaultNexthopAddress | read-create | current | Next hop IP address of apply default next hop action. |
| 1.3.6.1.4.1.25506.2.113.2.6.1.5 | Columnhh3cPBRMibApplyDefaultNexthopTrackId | read-create | current | Identifier of track object related with default next hop. Specifies a track entry by its number in the range of 1 to 1024. Setting 0 indicates closing this fun… |
| 1.3.6.1.4.1.25506.2.113.2.6.1.6 | Columnhh3cPBRMibApplyDefaultNexthopDirect | read-create | current | Direct route attribute of apply default next hop address according to route information. |
| 1.3.6.1.4.1.25506.2.113.2.6.1.7 | Columnhh3cPBRMibApplyDefaultNexthopRowStatus | read-create | current | Operation status of this table entry. Three actions are used: active, createAndGo, and destroy. |
| 1.3.6.1.4.1.25506.2.113.2.6.1.8 | Columnhh3cPBRMibApplyDefNexthopInbVpn | read-create | current | Specifies the VPN instance where the inbound interface belongs. If the value is set to TRUE, the VPN instance name will be ignored. |
| 1.3.6.1.4.1.25506.2.113.2.6.1.9 | Columnhh3cPBRMibApplyDefNexthopPathId | read-create | current | Specifies a service chain by its path ID in the range of 1 and 16777215. |
| 1.3.6.1.4.1.25506.2.113.2.6.1.10 | Columnhh3cPBRMibApplyDefNexthopPathInd | read-create | current | Specifies a node in the service chain as a default next hop by its index in the range of 1 and 255. |