HUAWEI-MINM-MIB
21 objects
No module-level DESCRIPTION found.
Imported Objects
| HUAWEI-L2IF-MIB | VlanList |
| HUAWEI-MIB | hwDatacomm |
| IANA-ADDRESS-FAMILY-NUMBERS-MIB | AddressFamilyNumbers |
| IF-MIB | InterfaceIndex InterfaceIndexOrZero |
| P-BRIDGE-MIB | EnabledStatus |
| Q-BRIDGE-MIB | VlanId VlanIdOrNone |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Counter64 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | MacAddress RowStatus TEXTUAL-CONVENTION TimeStamp TruthValue |
| TRANSPORT-ADDRESS-MIB | TransportAddress TransportDomain |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| HWAdminStatus | INTEGER { up(1), down(2) } | current | Indicates the administration status as follows: up(1), down(2) |
| HWApsInterval | INTEGER { apsInterval3dot3ms(1), apsInterval5ms(2), apsInterval10ms(3), apsInterval15ms(4), apsInterval20ms(5), apsInterval30ms(6) } | current | Indicates the time interval for fast sending of Aps packets described in the G.8031. By default, it is 3.3 ms. Optional values for sending interval are as follows: apsInterval3dot3ms(1): indicates a sending interval of … |
| HwDot1agCfmCcmInterval | INTEGER { intervalInvalid(1), interval300Hz(2), interval10ms(3), interval100ms(4), interval1s(5), interval10s(6), interval1min(7), interval10min(8), interval20ms(9), interval30ms(10), interval50ms(11) } | current | Indicates the interval at which CCMs are sent by a MEP. The possible values are: intervalInvalid(1) No CCMs are sent (disabled). interval300Hz(2) CCMs are sent every 3 1/3 milliseconds (300Hz). interval10ms(3) CCMs are … |
| HwDot1agCfmEgressActionFieldValue | INTEGER { egrOK (1), egrDown (2), egrBlocked (3), egrVid (4) } | current | Possible values returned in the egress action field |
| HwDot1agCfmIngressActionFieldValue | INTEGER { ingOk (1), ingDown (2), ingBlocked (3), ingVid (4) } | current | Possible values returned in the ingress action field. |
| HwDot1agCfmMepIdOrZero | Unsigned32 (0 | 1..8191) | current | Indicates the Maintenance association End Point Identifier (MEPID): A small integer, unique over a given Maintenance Association, identifying a specific MEP. The special value 0 is allowed to indicate special cases, for… |
| HwDot1agCfmRelayActionFieldValue | INTEGER { rlyHit(1), rlyFdb(2), rlyMpdb(3) } | current | Indicates the possible values the Relay action field can take. |
| HWInterfaceType | INTEGER { transparent(1), oneToOne(2), bundling(3) } | current | Indicates the interface type of a service instance. The encApsulation mapping modes of the service instance can be configured as follows: transparent(1): indicates the transparent transmission mode. oneToOne(2): indicat… |
| HwLldpChassisId | OCTET STRING (SIZE (1..255)) | current | This TC describes the format of a chassis identifier string. Objects of this type are always used with an associated LldpChassisIdSubtype object, which identifies the format of the particular LldpChassisId object instan… |
| HwLldpChassisIdSubtype | INTEGER { chassisComponent(1), interfaceAlias(2), portComponent(3), macAddress(4), networkAddress(5), interfaceName(6), local(7) } | current | This TC describes the source of a chassis identifier. The enumeration 'chassisComponent(1)' represents a chassis identifier based on the value of entPhysicalAlias object (defined in IETF RFC 2737) for a chassis componen… |
| HwLldpManAddress | OCTET STRING (SIZE (1..31)) | current | The value of a management address associated with the LLDP agent that may be used to reach higher layer entities to assist discovery by network management. It should be noted that appropriate security credentials, such … |
| HwLldpManAddrIfSubtype | INTEGER { unknown(1), ifIndex(2), systemPortNumber(3) } | current | This TC describes the basis of a particular type of interface associated with the management address. The enumeration 'unknown(1)' represents the case where the interface is not known. The enumeration 'ifIndex(2)' repre… |
| HwLldpPortId | OCTET STRING (SIZE (1..255)) | current | This TC describes the format of a port identifier string. Objects of this type are always used with an associated LldpPortIdSubtype object, which identifies the format of the particular LldpPortId object instance. If th… |
| HwLldpPortIdSubtype | INTEGER { interfaceAlias(1), portComponent(2), macAddress(3), networkAddress(4), interfaceName(5), agentCircuitId(6), local(7) } | current | This TC describes the source of a particular type of port identifier used in the LLDP MIB. The enumeration 'interfaceAlias(1)' represents a port identifier based on the ifAlias MIB object, defined in IETF RFC 2863. The … |
| HWOperStatus | INTEGER { up(1), down(2) } | current | Indicates the operation status as follows: up(1), down(2) |
| HWProcessBehavior | INTEGER { discard(1), forward(2) } | current | Indicates the processing behavior of packets as follows: discard(1), forward(2) |
| HWProtectMode | INTEGER { onePlusOneBidirectional(1), onePlusOneUnidirectional(2), oneToOne(3) } | current | Indicates the protection modes of the G.8031 Aps protection group of mac-tunnels. oneplusonebidirectional(1): 1 + 1 switchover protection modes on both ends oneplusoneunidirectional(2): 1 + 1 switchover protection modes… |
| HWProtectProtocol | INTEGER { protocolAps(1), protocolOam(2) } | current | Indicates the protection protocol of the protection group of mac-tunnels. protocolAps(1): use an APS protocol to enhance the protection switching. protocolOam(2): not using any APS protocol to enhance the protection swi… |
| HWServiceType | INTEGER { p2p(1), mp2mp(2) } | current | Indicates the type of a service instance as follows: p2p(1): indicates the type of a point-to-point service instance. mp2mp(2): indicates the type of a multi-point to multi-point service instance. By default, the servic… |
| HWStaticMacFwdType | INTEGER { static(1), blackhole(2) } | current | Indicates the type of the static MAC forwarding table of a service instance: static(1): indicates a static entry. blackhole(2): indicates a blackhole entry. |
| HWSwitchOperation | INTEGER { clear(1), lock(2), force(3), manual(4), null(5) } | current | Indicates the switchover commands for the Aps protection group of mac-tunnels. The priority levels in a descending order are: clear, lock, force and manual. clear(1): clears the lock, force and manual commands, and WTR … |