INFINERA-ENTITY-BMM-MIB
25 objects
No module-level DESCRIPTION found.
Imported Objects
| ENTITY-MIB | entPhysicalIndex |
| INFINERA-REG-MIB | equipment |
| INFINERA-TC-MIB | FloatTenths InfnEqptType InfnMaxChRatePlan |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | DisplayString RowStatus TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.21296.2.2.2.1.3 | IdentitybmmMIB | |||
| 1.3.6.1.4.1.21296.2.2.2.1.3.1 | TablebmmTable | not-accessible | current | A list of BMM entries. Each entry is uniquely identified by the value of entPhysicalIndex. |
| 1.3.6.1.4.1.21296.2.2.2.1.3.1.1 | RowbmmEntry | not-accessible | current | A BMM entry containing information pertaining to Infinera BMM modules. Entries will exist in this table for entPhysicalEntries of type BMM. |
| 1.3.6.1.4.1.21296.2.2.2.1.3.1.1.1 | ColumnbmmMoId | read-create | current | This should be specified in the format of x-A-y. where x is the chassis MoId and y is the slot in which BMM is present for example 1-A-1, 2-A-1 etc. |
| 1.3.6.1.4.1.21296.2.2.2.1.3.1.1.2 | ColumnbmmProvisonedType | read-create | current | The configured circuit pack type. |
| 1.3.6.1.4.1.21296.2.2.2.1.3.1.1.3 | ColumnbmmRxAmpDeviceSetpoint | read-only | current | Current gain value for DAMP. |
| 1.3.6.1.4.1.21296.2.2.2.1.3.1.1.4 | ColumnbmmRxAmpDeviceTarget | read-only | current | Target gain value for DAMP. |
| 1.3.6.1.4.1.21296.2.2.2.1.3.1.1.5 | ColumnbmmRxLastAmpDeviceCommitTs | read-only | current | The last gain adjusted time by DAMP protocol. |
| 1.3.6.1.4.1.21296.2.2.2.1.3.1.1.6 | ColumnbmmDisableGainControlLoop | read-create | current | Disable Gain Control Loop |
| 1.3.6.1.4.1.21296.2.2.2.1.3.1.1.7 | ColumnbmmLaunchPowerOffset | read-create | current | The BMM launch power will be adjusted by this value. The range of valid values is -2dB/channel to +2dB/channel. |
| 1.3.6.1.4.1.21296.2.2.2.1.3.1.1.8 | ColumnbmmNumberOfChannel | read-create | current | Number of active channels in OTS. The values can be 160, 80, 40 and 20. |
| 1.3.6.1.4.1.21296.2.2.2.1.3.1.1.9 | ColumnbmmTxDampSeqNum | read-only | current | Current Tx DAMP sequence number. |
| 1.3.6.1.4.1.21296.2.2.2.1.3.1.1.10 | ColumnbmmRxDampSeqNum | read-only | current | Current Rx DAMP sequence number. |
| 1.3.6.1.4.1.21296.2.2.2.1.3.1.1.11 | ColumnbmmTilt | read-create | current | This attribute is an offset to the gain tilt of the BMM/OAM/ORM - without any offset applied (offset of 0dB), the gain tilt of the BMM/OAM is 1dB. |
| 1.3.6.1.4.1.21296.2.2.2.1.3.1.1.12 | ColumnbmmOperatingMode | read-create | current | The BMM in mode at which is is operating. |
| 1.3.6.1.4.1.21296.2.2.2.1.3.1.1.13 | ColumnbmmGain | read-create | current | If configured mode is slteMode1 then user can input the required gain for rx EDFA. |
| 1.3.6.1.4.1.21296.2.2.2.1.3.1.1.14 | ColumnbmmRowStatus | read-create | current | The row status of this BMM entry. Because rows in this table are indexed by entPhysicalIndex, to create a new row one must choose a value of entPhysicalIndex t… |
| 1.3.6.1.4.1.21296.2.2.2.1.3.1.1.15 | ColumnbmmMaxChanRatePlan | read-create | current | Maximum Channel Rate Plan |
| 1.3.6.1.4.1.21296.2.2.2.1.3.1.1.16 | ColumnbmmCBandSoakCapableFW | read-only | current | |
| 1.3.6.1.4.1.21296.2.2.2.1.3.1.1.17 | ColumnbmmSuccessfulACGRunTime | read-only | current | |
| 1.3.6.1.4.1.21296.2.2.2.1.3.3 | NodebmmConformance | |||
| 1.3.6.1.4.1.21296.2.2.2.1.3.3.1 | NodebmmCompliances | |||
| 1.3.6.1.4.1.21296.2.2.2.1.3.3.1.1 | CompliancebmmCompliance | current | Describes the requirements for conformance to the BMM-MIB | |
| 1.3.6.1.4.1.21296.2.2.2.1.3.3.2 | NodebmmGroups | |||
| 1.3.6.1.4.1.21296.2.2.2.1.3.3.2.1 | GroupbmmGroup | current | A collection of objects for managing a BMM module |