L2TP-MIB
167 objects
The MIB module that describes managed objects of general use by the Layer Two Transport Protocol.
Imported Objects
| IF-MIB | InterfaceIndex |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Counter64 Gauge32 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE transmission Unsigned32 |
| SNMPv2-TC | RowStatus StorageType TEXTUAL-CONVENTION TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.10.95 | Identityl2tp | The MIB module that describes managed objects of general use by the Layer Two Transport Protocol. | ||
| 1.3.6.1.2.1.10.95.0 | Nodel2tpNotifications | |||
| 1.3.6.1.2.1.10.95.0.1 | Notificationl2tpTunnelAuthFailure | current | A l2tpTunnelAuthFailure trap signifies that an attempt to establish a tunnel to a remote peer has failed authentication. | |
| 1.3.6.1.2.1.10.95.1 | Nodel2tpObjects | |||
| 1.3.6.1.2.1.10.95.1.1 | Nodel2tpScalar | |||
| 1.3.6.1.2.1.10.95.1.1.1 | Nodel2tpConfig | |||
| 1.3.6.1.2.1.10.95.1.1.1.1 | Scalarl2tpAdminState | read-write | current | This object defines the administrative state of the L2TP protocol. Setting this object to 'disabled' causes all tunnels to be immediately disconnected and no f… |
| 1.3.6.1.2.1.10.95.1.1.1.2 | Scalarl2tpDrainTunnels | read-write | current | Setting this object to 'true' will prevent any new tunnels and/or sessions to be either initiated or accepted but does NOT disconnect any active tunnels/sessio… |
| 1.3.6.1.2.1.10.95.1.1.2 | Nodel2tpStats | |||
| 1.3.6.1.2.1.10.95.1.1.2.1 | Scalarl2tpProtocolVersions | read-only | current | Vector of supported L2TP protocol version and revision numbers. Supported versions are identified via a two octet pairing where the first octet indicates the v… |
| 1.3.6.1.2.1.10.95.1.1.2.2 | Scalarl2tpVendorName | read-only | current | This object identifies the Vendor name of the L2TP protocol stack. |
| 1.3.6.1.2.1.10.95.1.1.2.3 | Scalarl2tpFirmwareRev | read-only | current | This object defines the firmware revision for the L2TP protocol stack. |
| 1.3.6.1.2.1.10.95.1.1.2.4 | Scalarl2tpDrainingTunnels | read-only | current | This object indicates if the local L2TP is draining off sessions from all tunnels. |
| 1.3.6.1.2.1.10.95.1.2 | Tablel2tpDomainConfigTable | not-accessible | current | The L2TP Domain configuration table. This table contains objects that can be used to configure the operational characteristics of a tunnel domain. There is a 1… |
| 1.3.6.1.2.1.10.95.1.2.1 | Rowl2tpDomainConfigEntry | not-accessible | current | An L2TP Domain configuration entry. An entry in this table may correspond to a single endpoint or a group of tunnel endpoints. |
| 1.3.6.1.2.1.10.95.1.2.1.1 | Columnl2tpDomainConfigId | not-accessible | current | The identifier, usually in the form of a Domain Name (full or partial), describing a single tunnel endpoint or a domain of tunnel endpoints. This is typically … |
| 1.3.6.1.2.1.10.95.1.2.1.2 | Columnl2tpDomainConfigAdminState | read-create | current | This object defines the administrative state of this tunnel domain. Setting this object to disabled(2) causes all tunnels to be immediately disconnected and no… |
| 1.3.6.1.2.1.10.95.1.2.1.3 | Columnl2tpDomainConfigDrainTunnels | read-create | current | Setting this object to 'true' will prevent any new tunnels and/or sessions from being either initiated or accepted but does NOT disconnect any active tunnels/s… |
| 1.3.6.1.2.1.10.95.1.2.1.4 | Columnl2tpDomainConfigAuth | read-create | current | This object describes how tunnel peers belonging to this domain are to be authenticated. The value simple(2) indicates that peers are authenticated simply by t… |
| 1.3.6.1.2.1.10.95.1.2.1.5 | Columnl2tpDomainConfigSecret | read-create | current | This object is used to configure the shared secret used during the tunnel authentication phase of tunnel establishment. This object MUST be accessible only via… |
| 1.3.6.1.2.1.10.95.1.2.1.6 | Columnl2tpDomainConfigTunnelSecurity | read-create | current | This object defines whether this tunnel domain requires that all tunnels are to be secured. The value of ipsec(3) indicates that all tunnel packets, control an… |
| 1.3.6.1.2.1.10.95.1.2.1.7 | Columnl2tpDomainConfigTunnelHelloInt | read-create | current | This object defines the interval in which Hello (or keep-alive) packets are to be sent by local peers belonging to this tunnel domain. The value zero effective… |
| 1.3.6.1.2.1.10.95.1.2.1.8 | Columnl2tpDomainConfigTunnelIdleTO | read-create | current | This object defines the period of time that an established tunnel belonging to this tunnel domain with no active sessions will wait before disconnecting the tu… |
| 1.3.6.1.2.1.10.95.1.2.1.9 | Columnl2tpDomainConfigControlRWS | read-create | current | This object defines the control channel receive window size for tunnels belonging to this domain. It specifies the maximum number of packets the tunnel peer be… |
| 1.3.6.1.2.1.10.95.1.2.1.10 | Columnl2tpDomainConfigControlMaxRetx | read-create | current | This object defines the maximum number of retransmissions which the L2TP stack will attempt for tunnels belonging to this domain before assuming that the peer … |
| 1.3.6.1.2.1.10.95.1.2.1.11 | Columnl2tpDomainConfigControlMaxRetxTO | read-create | current | This object defines the maximum retransmission timeout interval which the L2TP stack will wait for tunnels belonging to this domain before retransmitting a con… |
| 1.3.6.1.2.1.10.95.1.2.1.12 | Columnl2tpDomainConfigPayloadSeq | read-create | current | This object determines whether or not session payload packets will be requested to be sent with sequence numbers from tunnel peers belonging to this domain. Th… |
| 1.3.6.1.2.1.10.95.1.2.1.13 | Columnl2tpDomainConfigReassemblyTO | read-create | current | This object defines the number of milliseconds that local peers of this tunnel domain will wait before processing payload packets that were received out of seq… |
| 1.3.6.1.2.1.10.95.1.2.1.14 | Columnl2tpDomainConfigProxyPPPAuth | read-create | current | This object is used to configure the sending or acceptance of the PPP Proxy Authentication AVP's on the LAC or LNS. |
| 1.3.6.1.2.1.10.95.1.2.1.15 | Columnl2tpDomainConfigStorageType | read-create | current | The storage type for this conceptual row. Conceptual rows having the value 'permanent' must allow write-access at a minimum to: - l2tpDomainConfigAdminState an… |
| 1.3.6.1.2.1.10.95.1.2.1.16 | Columnl2tpDomainConfigStatus | read-create | current | The status of this Domain entry. Columnar objects corresponding to this conceptual row may be modified according to their description clauses when this RowStat… |
| 1.3.6.1.2.1.10.95.1.3 | Tablel2tpDomainStatsTable | not-accessible | current | The L2TP Domain Status and Statistics table. This table contains objects that can be used to describe the current status and statistics of a tunnel domain. The… |
| 1.3.6.1.2.1.10.95.1.3.1 | Rowl2tpDomainStatsEntry | not-accessible | current | An L2TP Domain Stats entry. An entry in this table may correspond to a single endpoint or a group of tunnel endpoints. |
| 1.3.6.1.2.1.10.95.1.3.1.1 | Columnl2tpDomainStatsTotalTunnels | read-only | current | This object returns the total number of tunnels that have successfully reached the established state for this tunnel domain. |
| 1.3.6.1.2.1.10.95.1.3.1.2 | Columnl2tpDomainStatsFailedTunnels | read-only | current | This object returns the number of tunnels that failed (eg: connection timeout, unsupported or malformed AVP's etc) to reach the established state for this tunn… |
| 1.3.6.1.2.1.10.95.1.3.1.3 | Columnl2tpDomainStatsFailedAuths | read-only | current | This object returns the number of failed tunnel connection attempts for this domain because the tunnel peer failed authentication. |
| 1.3.6.1.2.1.10.95.1.3.1.4 | Columnl2tpDomainStatsActiveTunnels | read-only | current | This object returns the number of tunnels that are currently active for this domain. |
| 1.3.6.1.2.1.10.95.1.3.1.5 | Columnl2tpDomainStatsTotalSessions | read-only | current | This object returns the total number of sessions that have successfully reached the established state for this tunnel domain. |
| 1.3.6.1.2.1.10.95.1.3.1.6 | Columnl2tpDomainStatsFailedSessions | read-only | current | This object returns the number of sessions that failed (eg: connection timeout, unsupported or malformed AVP's etc) to reach the established state for this tun… |
| 1.3.6.1.2.1.10.95.1.3.1.7 | Columnl2tpDomainStatsActiveSessions | read-only | current | This object returns the number of sessions that are currently active for this domain. |
| 1.3.6.1.2.1.10.95.1.3.1.8 | Columnl2tpDomainStatsDrainingTunnels | read-only | current | This object indicates if this domain is draining off sessions from all tunnels. |
| 1.3.6.1.2.1.10.95.1.3.1.9 | Columnl2tpDomainStatsControlRxOctets | read-only | current | This object returns the number of control channel octets received for this tunnel domain. |
| 1.3.6.1.2.1.10.95.1.3.1.10 | Columnl2tpDomainStatsControlRxPkts | read-only | current | This object returns the number of control packets received for this tunnel domain. |
| 1.3.6.1.2.1.10.95.1.3.1.11 | Columnl2tpDomainStatsControlTxOctets | read-only | current | This object returns the number of control channel octets that were transmitted to tunnel endpoints for this domain. |
| 1.3.6.1.2.1.10.95.1.3.1.12 | Columnl2tpDomainStatsControlTxPkts | read-only | current | This object returns the number of control packets that were transmitted to tunnel endpoints for this domain. |
| 1.3.6.1.2.1.10.95.1.3.1.13 | Columnl2tpDomainStatsPayloadRxOctets | read-only | current | This object returns the number of payload channel octets that were received for this tunnel domain. |
| 1.3.6.1.2.1.10.95.1.3.1.14 | Columnl2tpDomainStatsPayloadRxPkts | read-only | current | This object returns the number of payload packets that were received for this tunnel domain. |
| 1.3.6.1.2.1.10.95.1.3.1.15 | Columnl2tpDomainStatsPayloadRxDiscs | read-only | current | This object returns the number of received payload packets that were discarded by this tunnel domain. |
| 1.3.6.1.2.1.10.95.1.3.1.16 | Columnl2tpDomainStatsPayloadTxOctets | read-only | current | This object returns the number of payload channel octets that were transmitted to tunnel peers within this tunnel domain. |
| 1.3.6.1.2.1.10.95.1.3.1.17 | Columnl2tpDomainStatsPayloadTxPkts | read-only | current | This object returns the number of payload packets that were transmitted to tunnel peers within this tunnel domain. |
| 1.3.6.1.2.1.10.95.1.3.1.18 | Columnl2tpDomainStatsControlHCRxOctets | read-only | current | This object is a 64-bit version of l2tpDomainStatsControlRxOctets. |
| 1.3.6.1.2.1.10.95.1.3.1.19 | Columnl2tpDomainStatsControlHCRxPkts | read-only | current | This object is a 64-bit version of l2tpDomainStatsControlRxPkts. |
| 1.3.6.1.2.1.10.95.1.3.1.20 | Columnl2tpDomainStatsControlHCTxOctets | read-only | current | This object is a 64-bit version of l2tpDomainStatsControlTxOctets. |
| 1.3.6.1.2.1.10.95.1.3.1.21 | Columnl2tpDomainStatsControlHCTxPkts | read-only | current | This object is a 64-bit version of l2tpDomainStatsControlTxPkts. |
| 1.3.6.1.2.1.10.95.1.3.1.22 | Columnl2tpDomainStatsPayloadHCRxOctets | read-only | current | This object is a 64-bit version of l2tpDomainStatsPayloadRxOctets. |
| 1.3.6.1.2.1.10.95.1.3.1.23 | Columnl2tpDomainStatsPayloadHCRxPkts | read-only | current | This object is a 64-bit version of l2tpDomainStatsPayloadRxPkts. |
| 1.3.6.1.2.1.10.95.1.3.1.24 | Columnl2tpDomainStatsPayloadHCRxDiscs | read-only | current | This object is a 64-bit version of l2tpDomainStatsPayloadRxDiscs. |
| 1.3.6.1.2.1.10.95.1.3.1.25 | Columnl2tpDomainStatsPayloadHCTxOctets | read-only | current | This object is a 64-bit version of l2tpDomainStatsPayloadTxOctets. |
| 1.3.6.1.2.1.10.95.1.3.1.26 | Columnl2tpDomainStatsPayloadHCTxPkts | read-only | current | This object is a 64-bit version of l2tpDomainStatsPayloadTxPkts. |
| 1.3.6.1.2.1.10.95.1.4 | Tablel2tpTunnelConfigTable | not-accessible | current | The L2TP tunnel configuration table. This table contains objects that can be used to (re)configure the operational characteristics of a single L2TP tunnel. The… |
| 1.3.6.1.2.1.10.95.1.4.1 | Rowl2tpTunnelConfigEntry | not-accessible | current | A L2TP tunnel interface configuration entry. Entries in this table come and go as a result of protocol interactions or on management operations. The latter occ… |
| 1.3.6.1.2.1.10.95.1.4.1.1 | Columnl2tpTunnelConfigIfIndex | not-accessible | current | This value for this object is equal to the value of ifIndex of the Interfaces MIB for tunnel interfaces of type L2TP. |
| 1.3.6.1.2.1.10.95.1.4.1.2 | Columnl2tpTunnelConfigDomainId | read-write | current | The tunnel domain that this tunnel belongs to. A LNS tunnel endpoint will typically inherit this value from the endpoint domain table. A LAC may be provided wi… |
| 1.3.6.1.2.1.10.95.1.4.1.3 | Columnl2tpTunnelConfigAuth | read-write | current | This object describes how L2TP tunnel peers are to be authenticated. The value 'simple' indicates that peers are authenticated simply by their host name as des… |
| 1.3.6.1.2.1.10.95.1.4.1.4 | Columnl2tpTunnelConfigSecret | read-write | current | This object is used to configure the shared secret used during the tunnel authentication phase of tunnel establishment. This object cannot be modified when the… |
| 1.3.6.1.2.1.10.95.1.4.1.5 | Columnl2tpTunnelConfigSecurity | read-write | current | This object defines whether this tunnel is to be secured. The value of 'ipSec' indicates that all tunnel packets, control and session, have IP Security headers… |
| 1.3.6.1.2.1.10.95.1.4.1.6 | Columnl2tpTunnelConfigHelloInterval | read-write | current | This object defines the interval in which Hello (or keep-alive) packets are to be sent to the tunnel peer. The value zero effectively disables the sending of H… |
| 1.3.6.1.2.1.10.95.1.4.1.7 | Columnl2tpTunnelConfigIdleTimeout | read-write | current | This object defines the period of time that an established tunnel with no sessions will wait before disconnecting the tunnel. A value of zero indicates that th… |
| 1.3.6.1.2.1.10.95.1.4.1.8 | Columnl2tpTunnelConfigControlRWS | read-write | current | This object defines the control channel receive window size. It specifies the maximum number of packets the tunnel peer can send without waiting for an acknowl… |
| 1.3.6.1.2.1.10.95.1.4.1.9 | Columnl2tpTunnelConfigControlMaxRetx | read-write | current | This object defines the number of retransmissions which the tunnel will attempt before assuming that the peer is no longer responding. A value of zero indicate… |
| 1.3.6.1.2.1.10.95.1.4.1.10 | Columnl2tpTunnelConfigControlMaxRetxTO | read-write | current | This object defines the maximum retransmission timeout interval which the tunnel will wait before retrans- mitting a control packet that has not been acknowled… |
| 1.3.6.1.2.1.10.95.1.4.1.11 | Columnl2tpTunnelConfigPayloadSeq | read-write | current | This object determines whether or not session payload packets will be requested to be sent with sequence numbers from tunnel peers belonging to this domain. Th… |
| 1.3.6.1.2.1.10.95.1.4.1.12 | Columnl2tpTunnelConfigReassemblyTO | read-write | current | This object defines the number of milliseconds that this tunnel will wait before processing payload packets that were received out of sequence (which are waiti… |
| 1.3.6.1.2.1.10.95.1.4.1.13 | Columnl2tpTunnelConfigTransport | read-write | current | This object defines the underlying transport media that is in use for this tunnel entry. Different tunnel transports may define MIB extensions to the L2TP tunn… |
| 1.3.6.1.2.1.10.95.1.4.1.14 | Columnl2tpTunnelConfigDrainTunnel | read-write | current | Setting this object to 'true' will prevent any new session from being either initiated or accepted but does NOT disconnect any active sessions for this tunnel.… |
| 1.3.6.1.2.1.10.95.1.4.1.15 | Columnl2tpTunnelConfigProxyPPPAuth | read-write | current | This object is used to configure the sending or acceptance of the session PPP Proxy Authentication AVP's on the LAC or LNS. |
| 1.3.6.1.2.1.10.95.1.5 | Tablel2tpTunnelStatsTable | not-accessible | current | The L2TP tunnel status and statistics table. This table contains objects that can be used to describe the current status and statistics of a single L2TP tunnel… |
| 1.3.6.1.2.1.10.95.1.5.1 | Rowl2tpTunnelStatsEntry | not-accessible | current | An L2TP tunnel interface stats entry. |
| 1.3.6.1.2.1.10.95.1.5.1.1 | Columnl2tpTunnelStatsLocalTID | read-only | current | This object contains the local tunnel Identifier. |
| 1.3.6.1.2.1.10.95.1.5.1.2 | Columnl2tpTunnelStatsRemoteTID | read-only | current | This object contains the remote tunnel Identifier. |
| 1.3.6.1.2.1.10.95.1.5.1.3 | Columnl2tpTunnelStatsState | read-only | current | This field contains the current state of the control tunnel. |
| 1.3.6.1.2.1.10.95.1.5.1.4 | Columnl2tpTunnelStatsInitiated | read-only | current | This object indicates whether the tunnel was initiated locally or by the remote tunnel peer. |
| 1.3.6.1.2.1.10.95.1.5.1.5 | Columnl2tpTunnelStatsRemoteHostName | read-only | current | This object contains the host name as discovered during the tunnel establishment phase (via the Host Name AVP) of the L2TP peer. If the tunnel is idle this obj… |
| 1.3.6.1.2.1.10.95.1.5.1.6 | Columnl2tpTunnelStatsRemoteVendorName | read-only | current | This object identifies the vendor name of the peer's L2TP implementation. If the tunnel is idle this object should maintain its value from the last time it was… |
| 1.3.6.1.2.1.10.95.1.5.1.7 | Columnl2tpTunnelStatsRemoteFirmwareRev | read-only | current | This object contains the tunnel peer's firmware revision number. If the tunnel is idle this object should maintain its value from the last time it was connecte… |
| 1.3.6.1.2.1.10.95.1.5.1.8 | Columnl2tpTunnelStatsRemoteProtocolVer | read-only | current | This object describes the protocol version and revision of the tunnel peers implementation. The first octet contains the protocol version. The second octet con… |
| 1.3.6.1.2.1.10.95.1.5.1.9 | Columnl2tpTunnelStatsInitialRemoteRWS | read-only | current | This object contains the initial remote peer's receive window size as indicated by the tunnel peer (in the RWS AVP) during the tunnel establishment phase. If t… |
| 1.3.6.1.2.1.10.95.1.5.1.10 | Columnl2tpTunnelStatsBearerCaps | read-only | current | This object describes the Bearer Capabilities of the tunnel peer. If the tunnel is idle this object should maintain its value from the last time it was connect… |
| 1.3.6.1.2.1.10.95.1.5.1.11 | Columnl2tpTunnelStatsFramingCaps | read-only | current | This object describes the Framing Capabilities of the tunnel peer. If the tunnel is idle this object should maintain its value from the last time it was connec… |
| 1.3.6.1.2.1.10.95.1.5.1.12 | Columnl2tpTunnelStatsControlRxPkts | read-only | current | This object contains the number of control packets received on the tunnel. |
| 1.3.6.1.2.1.10.95.1.5.1.13 | Columnl2tpTunnelStatsControlRxZLB | read-only | current | This object returns a count of the number of Zero Length Body control packet acknowledgement packets that were received. |
| 1.3.6.1.2.1.10.95.1.5.1.14 | Columnl2tpTunnelStatsControlOutOfSeq | read-only | current | This object returns a count of the number of control packets that were not received in the correct order (as per the sequence number) on this tunnel including … |
| 1.3.6.1.2.1.10.95.1.5.1.15 | Columnl2tpTunnelStatsControlOutOfWin | read-only | current | This object contains the number of control packets that were received outside of the offered receive window. It is implementation specific as to whether these … |
| 1.3.6.1.2.1.10.95.1.5.1.16 | Columnl2tpTunnelStatsControlTxPkts | read-only | current | This object contains the number of control packets that were transmitted to the tunnel peer. |
| 1.3.6.1.2.1.10.95.1.5.1.17 | Columnl2tpTunnelStatsControlTxZLB | read-only | current | This object contains the number of Zero Length Body control packets transmitted to the tunnel peer. |
| 1.3.6.1.2.1.10.95.1.5.1.18 | Columnl2tpTunnelStatsControlAckTO | read-only | current | This object returns a count of the number of control packet timeouts due to the lack of a timely acknowledgement from the tunnel peer. |
| 1.3.6.1.2.1.10.95.1.5.1.19 | Columnl2tpTunnelStatsCurrentRemoteRWS | read-only | current | This object contains the current remote receive window size as determined by the local flow control mechanism employed. |
| 1.3.6.1.2.1.10.95.1.5.1.20 | Columnl2tpTunnelStatsTxSeq | read-only | current | This object contains the next send sequence number for the control channel. |
| 1.3.6.1.2.1.10.95.1.5.1.21 | Columnl2tpTunnelStatsTxSeqAck | read-only | current | This object contains the send sequence number that the tunnel peer has acknowledged for the control channel. The flow control state can be determined by subtra… |
| 1.3.6.1.2.1.10.95.1.5.1.22 | Columnl2tpTunnelStatsRxSeq | read-only | current | This object contains the next receive sequence number expected to be received on this control channel. |
| 1.3.6.1.2.1.10.95.1.5.1.23 | Columnl2tpTunnelStatsRxSeqAck | read-only | current | This object contains the last receive sequence number that was acknowledged back to the tunnel peer for the control channel. |
| 1.3.6.1.2.1.10.95.1.5.1.24 | Columnl2tpTunnelStatsTotalSessions | read-only | current | This object contains the total number of sessions that this tunnel has successfully connected through to its tunnel peer since this tunnel was created. |
| 1.3.6.1.2.1.10.95.1.5.1.25 | Columnl2tpTunnelStatsFailedSessions | read-only | current | This object contains the total number of sessions that were initiated but failed to reach the established phase. |
| 1.3.6.1.2.1.10.95.1.5.1.26 | Columnl2tpTunnelStatsActiveSessions | read-only | current | This object contains the total number of sessions in the established state for this tunnel. |
| 1.3.6.1.2.1.10.95.1.5.1.27 | Columnl2tpTunnelStatsLastResultCode | read-only | current | This object contains the last value of the result code as described in the Result Code AVP which caused the tunnel to disconnect. |
| 1.3.6.1.2.1.10.95.1.5.1.28 | Columnl2tpTunnelStatsLastErrorCode | read-only | current | This object contains the last value of the error code as described in the Result Code AVP which caused the tunnel to disconnect. |
| 1.3.6.1.2.1.10.95.1.5.1.29 | Columnl2tpTunnelStatsLastErrorMessage | read-only | current | This object contains the last value of the optional message as described in the Result Code AVP which caused the tunnel to disconnect. |
| 1.3.6.1.2.1.10.95.1.5.1.30 | Columnl2tpTunnelStatsDrainingTunnel | read-only | current | This object indicates if this tunnel is draining off sessions. This object will return false(2) when the tunnel is not draining sessions or after the last sess… |
| 1.3.6.1.2.1.10.95.1.7 | Tablel2tpSessionStatsTable | not-accessible | current | The L2TP session status and statistics table. This table contains the objects that can be used to describe the current status and statistics of a single L2TP t… |
| 1.3.6.1.2.1.10.95.1.7.1 | Rowl2tpSessionStatsEntry | not-accessible | current | An L2TP session interface stats entry. |
| 1.3.6.1.2.1.10.95.1.7.1.1 | Columnl2tpSessionStatsTunnelIfIndex | not-accessible | current | This object identifies the session's associated L2TP tunnel ifIndex value. |
| 1.3.6.1.2.1.10.95.1.7.1.2 | Columnl2tpSessionStatsIfIndex | read-only | current | This object identifies the ifIndex value of the interface from which PPP packets are being tunneled. For example this could be a DS0 ifIndex on a LAC or it wou… |
| 1.3.6.1.2.1.10.95.1.7.1.3 | Columnl2tpSessionStatsLocalSID | not-accessible | current | This object contains the local assigned session identifier for this session. |
| 1.3.6.1.2.1.10.95.1.7.1.4 | Columnl2tpSessionStatsRemoteSID | read-only | current | This object contains the remote assigned session identifier for this session. When a session is starting this value may be zero until the remote tunnel endpoin… |
| 1.3.6.1.2.1.10.95.1.7.1.5 | Columnl2tpSessionStatsUserName | read-only | current | This object identifies the peer session name on this interface. This is typically the login name of the remote user. If the user name is unknown to the local t… |
| 1.3.6.1.2.1.10.95.1.7.1.6 | Columnl2tpSessionStatsState | read-only | current | This object contains the current state of the session. |
| 1.3.6.1.2.1.10.95.1.7.1.7 | Columnl2tpSessionStatsCallType | read-only | current | This object indicates the type of call and the role this tunnel peer is providing for this session. For example, lacIncoming(1) indicates that this tunnel peer… |
| 1.3.6.1.2.1.10.95.1.7.1.8 | Columnl2tpSessionStatsCallSerialNumber | read-only | current | This object contains the serial number that has been assigned to this session. |
| 1.3.6.1.2.1.10.95.1.7.1.9 | Columnl2tpSessionStatsTxConnectSpeed | read-only | current | This object returns the last known transmit baud rate for this session. |
| 1.3.6.1.2.1.10.95.1.7.1.10 | Columnl2tpSessionStatsRxConnectSpeed | read-only | current | This object returns the last known receive baud rate for this session established. |
| 1.3.6.1.2.1.10.95.1.7.1.11 | Columnl2tpSessionStatsCallBearerType | read-only | current | This object describes the bearer type of this session. |
| 1.3.6.1.2.1.10.95.1.7.1.12 | Columnl2tpSessionStatsFramingType | read-only | current | This object describes the framing type of this session. |
| 1.3.6.1.2.1.10.95.1.7.1.13 | Columnl2tpSessionStatsPhysChanId | read-only | current | This object contains the physical channel identifier for the session. |
| 1.3.6.1.2.1.10.95.1.7.1.14 | Columnl2tpSessionStatsDNIS | read-only | current | This object identifies the Dialed Number Information String that the LAC obtained from the network for the session. If no DNIS was provided then a null string … |
| 1.3.6.1.2.1.10.95.1.7.1.15 | Columnl2tpSessionStatsCLID | read-only | current | This object identifies the Calling Line ID that the LAC obtained from the network for the session. If no CLID was provided then a null string will be returned. |
| 1.3.6.1.2.1.10.95.1.7.1.16 | Columnl2tpSessionStatsSubAddress | read-only | current | This object identifies the Sub Address that the LAC obtained from the network for the session. If no Sub Address was provided then a null string will be return… |
| 1.3.6.1.2.1.10.95.1.7.1.17 | Columnl2tpSessionStatsPrivateGroupID | read-only | current | This object identifies the Private Group Identifier used for this tunneled session. If no Private Group Identifier was provided then a null string will be retu… |
| 1.3.6.1.2.1.10.95.1.7.1.18 | Columnl2tpSessionStatsProxyLcp | read-only | current | Indicates whether the LAC performed proxy LCP for this session. |
| 1.3.6.1.2.1.10.95.1.7.1.19 | Columnl2tpSessionStatsAuthMethod | read-only | current | This object contains the proxy authentication method employed by the LAC for the session. If l2tpSessionProxyLcp is false(2) this object should not be interpre… |
| 1.3.6.1.2.1.10.95.1.7.1.20 | Columnl2tpSessionStatsSequencingState | read-only | current | This object defines which tunnel peers have requested payload sequencing. The value of both(4) indicates that both peers have requested payload sequencing. |
| 1.3.6.1.2.1.10.95.1.7.1.21 | Columnl2tpSessionStatsOutSequence | read-only | current | This object returns the total number of packets received for this session which were received out of sequence. |
| 1.3.6.1.2.1.10.95.1.7.1.22 | Columnl2tpSessionStatsReassemblyTO | read-only | current | This object returns the number of reassembly timeouts that have occurred for this session. |
| 1.3.6.1.2.1.10.95.1.7.1.23 | Columnl2tpSessionStatsTxSeq | read-only | current | This object contains the next send sequence number for for this session. |
| 1.3.6.1.2.1.10.95.1.7.1.24 | Columnl2tpSessionStatsRxSeq | read-only | current | This object contains the next receive sequence number expected to be received on this session. |
| 1.3.6.1.2.1.10.95.1.8 | Tablel2tpTunnelMapTable | not-accessible | current | The L2TP Tunnel index mapping table. This table is intended to assist management applications to quickly determine what the ifIndex value is for a given local … |
| 1.3.6.1.2.1.10.95.1.8.1 | Rowl2tpTunnelMapEntry | not-accessible | current | An L2TP tunnel index map entry. |
| 1.3.6.1.2.1.10.95.1.8.1.1 | Columnl2tpTunnelMapLocalTID | not-accessible | current | This object contains the local tunnel Identifier. |
| 1.3.6.1.2.1.10.95.1.8.1.2 | Columnl2tpTunnelMapIfIndex | read-only | current | This value for this object is equal to the value of ifIndex of the Interfaces MIB for tunnel interfaces of type L2TP. |
| 1.3.6.1.2.1.10.95.1.9 | Tablel2tpSessionMapTable | not-accessible | current | The L2TP Session index mapping table. This table is intended to assist management applications to map interfaces to a tunnel and session identifier. |
| 1.3.6.1.2.1.10.95.1.9.1 | Rowl2tpSessionMapEntry | not-accessible | current | An L2TP Session index map entry. |
| 1.3.6.1.2.1.10.95.1.9.1.1 | Columnl2tpSessionMapIfIndex | not-accessible | current | This object identifies the ifIndex value of the interface which is receiving or sending its packets over an L2TP tunnel. For example this could be a DS0 ifInde… |
| 1.3.6.1.2.1.10.95.1.9.1.2 | Columnl2tpSessionMapTunnelIfIndex | read-create | current | This object identifies the sessions associated L2TP tunnel ifIndex value. When this object is set it provides a binding between a particular interface identifi… |
| 1.3.6.1.2.1.10.95.1.9.1.3 | Columnl2tpSessionMapLocalSID | read-only | current | This object contains the local assigned session identifier for this session. |
| 1.3.6.1.2.1.10.95.1.9.1.4 | Columnl2tpSessionMapStatus | read-create | current | The status of this session map entry. |
| 1.3.6.1.2.1.10.95.3 | Nodel2tpTransports | |||
| 1.3.6.1.2.1.10.95.3.1 | Nodel2tpTransportIpUdp | |||
| 1.3.6.1.2.1.10.95.3.1.1 | Nodel2tpIpUdpObjects | |||
| 1.3.6.1.2.1.10.95.3.1.1.2 | Tablel2tpUdpStatsTable | not-accessible | current | The L2TP UDP/IP transport stats table. This table contains objects that can be used to describe the current status and statistics of the UDP/IP L2TP tunnel tra… |
| 1.3.6.1.2.1.10.95.3.1.1.2.1 | Rowl2tpUdpStatsEntry | not-accessible | current | An L2TP UDP/IP transport stats entry. |
| 1.3.6.1.2.1.10.95.3.1.1.2.1.1 | Columnl2tpUdpStatsIfIndex | not-accessible | current | This value for this object is equal to the value of ifIndex of the Interfaces MIB for tunnel interfaces of type L2TP and which have a L2TP transport of UDP/IP. |
| 1.3.6.1.2.1.10.95.3.1.1.2.1.2 | Columnl2tpUdpStatsPeerPort | read-only | current | This object reflects the peer's UDP port number used for this tunnel. When not known a value of zero should be returned. |
| 1.3.6.1.2.1.10.95.3.1.1.2.1.3 | Columnl2tpUdpStatsLocalPort | read-only | current | This object reflects the local UDP port number that this tunnel is bound to. |
| 1.3.6.1.2.1.10.95.3.1.2 | Nodel2tpIpUdpTraps | |||
| 1.3.6.1.2.1.10.95.4 | Nodel2tpConformance | |||
| 1.3.6.1.2.1.10.95.4.1 | Nodel2tpGroups | |||
| 1.3.6.1.2.1.10.95.4.1.1 | Groupl2tpConfigGroup | current | A collection of objects providing configuration information of the L2TP protocol, tunnels and sessions. | |
| 1.3.6.1.2.1.10.95.4.1.2 | Groupl2tpStatsGroup | current | A collection of objects providing status and statistics of the L2TP protocol, tunnels and sessions. | |
| 1.3.6.1.2.1.10.95.4.1.3 | Groupl2tpIpUdpGroup | current | A collection of objects providing status and statistics of the L2TP UDP/IP transport layer. | |
| 1.3.6.1.2.1.10.95.4.1.4 | Groupl2tpDomainGroup | current | A collection of objects providing configuration, status and statistics of L2TP tunnel domains. | |
| 1.3.6.1.2.1.10.95.4.1.5 | Groupl2tpMappingGroup | current | A collection of objects providing index mapping. | |
| 1.3.6.1.2.1.10.95.4.1.6 | Groupl2tpSecurityGroup | current | A collection of objects providing L2TP security configuration. | |
| 1.3.6.1.2.1.10.95.4.1.7 | Groupl2tpTrapGroup | current | A collection of L2TP trap events as specified in NOTIFICATION-TYPE constructs. | |
| 1.3.6.1.2.1.10.95.4.1.8 | Groupl2tpHCPacketGroup | current | A collection of objects providing High Capacity 64-bit counter objects. | |
| 1.3.6.1.2.1.10.95.4.2 | Nodel2tpCompliances | |||
| 1.3.6.1.2.1.10.95.4.2.1 | Compliancel2tpMIBFullCompliance | current | When this MIB is implemented with support for read-create and read-write, then such an implementation can claim full compliance. Such an implementation can the… | |
| 1.3.6.1.2.1.10.95.4.2.2 | Compliancel2tpMIBReadOnlyCompliance | read-only | current | When this MIB is implemented without support for read-create and read-write (i.e. in read-only mode), then such an implementation can claim read-only complianc… |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| L2tpMilliSeconds | Integer32 (0..2147483646) | current | A period of time measured in units of .001 of seconds when used in conjunction with the DISPLAY-HINT will show seconds and fractions of second with a resolution of .001 of a second. |