LANtern-MIB
258 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC1065-SMI | Counter enterprises Gauge IpAddress TimeTicks |
| RFC1212 MISSING | OBJECT-TYPE |
| RFC1215 MISSING | TRAP-TYPE |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.23 | Nodenovell | |||
| 1.3.6.1.4.1.23.1 | NodeproductType | |||
| 1.3.6.1.4.1.23.1.1 | NodenetworkMonitor | |||
| 1.3.6.1.4.1.23.1.1.1 | NodeethernetLANtern | |||
| 1.3.6.1.4.1.23.1.1.1.1 | NodecableFailure | A cableFailure(1) trap is generated whenever the LANtern network monitor detects a fault with the network cable. | ||
| 1.3.6.1.4.1.23.1.1.1.2 | NodepingNotification | A pingNotification(2) trap is generated whenever the LANtern network monitor receives the echo response to a proxy ping. | ||
| 1.3.6.1.4.1.23.1.1.1.3 | NodeduplicateIPAddr | A duplicateIPAddr(3) trap is generated whenever the LANtern network monitor first detects more than one host using the same IP address. | ||
| 1.3.6.1.4.1.23.1.1.1.4 | NodeutilizationAlarm | A utilizationAlarm(4) trap is generated whenever the percent utilization parameter enters or leaves an alarm condition as defined by the thresholds set in the … | ||
| 1.3.6.1.4.1.23.1.1.1.5 | NodeerrorsAlarm | An errorsAlarm(5) trap is generated whenever the percent errors parameter enters or leaves an alarm condition as defined by the thresholds set in the eAlarmTab… | ||
| 1.3.6.1.4.1.23.1.1.1.6 | NodebroadcastsAlarm | A broadcastsAlarm(6) trap is generated whenever the percent broadcasts parameter enters or leaves an alarm condition as defined by the thresholds set in the eA… | ||
| 1.3.6.1.4.1.23.1.1.1.7 | NodecollisionsAlarm | A collisionsAlarm(7) trap is generated whenever the percent collisions parameter enters or leaves an alarm condition as defined by the thresholds set in the eA… | ||
| 1.3.6.1.4.1.23.1.1.1.9 | NodehostInactive | A hostInactive(9) trap is generated whenever the LANtern network monitor first detects that a monitored host has not transmitted for the specified interval. Th… | ||
| 1.3.6.1.4.1.23.1.1.1.10 | NodehostActive | A hostActive(10) trap is generated whenever the LANtern network monitor first detects that a monitored host has begun transmitting again (after being inactive). | ||
| 1.3.6.1.4.1.23.1.1.1.11 | NodenewHost | A newHost(11) trap is generated whenever the LANtern network monitor first detects a new host transmitting on its network segment. | ||
| 1.3.6.1.4.1.23.1.1.1.12 | NodehostLimitExceeded | A hostLimitExceeded(12) trap is generated the first time the LANtern exceeds its host limit. eHostAddress is the address of the host which caused the limit to … | ||
| 1.3.6.1.4.1.23.2 | NodemibDoc | |||
| 1.3.6.1.4.1.23.2.1 | Nodelantern | |||
| 1.3.6.1.4.1.23.2.1.1 | NodelanternAdmin | |||
| 1.3.6.1.4.1.23.2.1.1.1 | ScalaradminIdentification | read-write | mandatory | An identifying ASCII string may be attached to the LANtern network monitor by writing adminIdentification. Conversely, the LANtern network monitor may be ident… |
| 1.3.6.1.4.1.23.2.1.1.2 | ScalaradminDateAndTime | read-write | mandatory | Reading adminDateAndTime returns the current date and time in use by the LANtern network monitor. The LANtern network monitor's date and time may be adjusted a… |
| 1.3.6.1.4.1.23.2.1.1.3 | ScalaradminTimeZone | read-write | mandatory | A DisplayString defining the time zone of the LANtern network monitor. adminTimeZone is neither parsed nor used by the LANtern network monitor, it is merely st… |
| 1.3.6.1.4.1.23.2.1.1.4 | ScalaradminPowerOnTime | read-only | mandatory | The date and time when the LANtern network monitor was last powered on or restarted. |
| 1.3.6.1.4.1.23.2.1.1.5 | ScalaradminPowerOffTime | read-only | mandatory | The date and time when the LANtern network monitor was last powered off or restarted. The value is 0 (midnight, 1 January 1900) after a cold start. |
| 1.3.6.1.4.1.23.2.1.1.6 | ScalaradminNetworkDataLink | read-write | mandatory | The type of data link encapsulation to be used on the monitored network. adminNetworkDataLink may be written at any time; however, the change does not take eff… |
| 1.3.6.1.4.1.23.2.1.1.7 | ScalaradminNetworkIPAddr | read-write | mandatory | The IP address to be used by the LANtern network monitor on the monitored network. adminNetworkIPAddr may be written at any time; however, the change does not … |
| 1.3.6.1.4.1.23.2.1.1.8 | ScalaradminNetworkSubnetMask | read-write | mandatory | The subnet mask for the monitored network. adminNetworkSubnetMask may be written at any time; however, the change does not take effect until the LANtern networ… |
| 1.3.6.1.4.1.23.2.1.1.9 | ScalaradminNetworkGateway | read-write | mandatory | The IP address of a gateway directly connected to the monitored network (the LANtern network monitor's default gateway). adminNetworkGateway may be written at … |
| 1.3.6.1.4.1.23.2.1.1.10 | TableadminClientTable | not-accessible | mandatory | A table providing data on all authorized LANtern clients. The table is accessed by adminClientIPAddr. A new entry may be created by writing to a nonexistent in… |
| 1.3.6.1.4.1.23.2.1.1.10.1 | RowadminClientEntry | not-accessible | mandatory | Data about each authorized client. |
| 1.3.6.1.4.1.23.2.1.1.10.1.1 | ColumnadminClientIPAddr | read-only | mandatory | The IP address (or portion thereof) of a station authorized to access the LANtern network monitor. |
| 1.3.6.1.4.1.23.2.1.1.10.1.2 | ColumnadminClientIPMask | read-write | mandatory | A 32-bit mask that is bitwise anded with the candidate client's IP address before attempting to match against adminClientIPAddr. |
| 1.3.6.1.4.1.23.2.1.1.10.1.3 | ColumnadminClientCommunities | read-write | mandatory | A bit array where the presence of a particular bit indicates that use of that particular community name is permitted. Bit Community 2^0 administrator 2^1 logge… |
| 1.3.6.1.4.1.23.2.1.1.10.1.4 | ColumnadminClientDelete | write-only | mandatory | A write (any value) causes the table entry to be deleted. |
| 1.3.6.1.4.1.23.2.1.1.11 | ScalaradminUnauthorizedIPAddr | not-accessible | mandatory | The IP address of the station that generated the authentication failure. |
| 1.3.6.1.4.1.23.2.1.1.12 | ScalaradminUnauthorizedCommunity | not-accessible | mandatory | The community name string used in the PDU that generated the authentication failure. |
| 1.3.6.1.4.1.23.2.1.1.13 | TableadminNotificationTable | not-accessible | mandatory | A list of all stations wishing to receive traps from the LANtern network monitor; accessed by adminNotificationIPAddr. A new entry may be created by writing to… |
| 1.3.6.1.4.1.23.2.1.1.13.1 | RowadminNotificationEntry | not-accessible | mandatory | Data for each station on the notification list. |
| 1.3.6.1.4.1.23.2.1.1.13.1.1 | ColumnadminNotificationIPAddr | read-only | mandatory | The IP address of the station wishing to receive traps from the LANtern network monitor. |
| 1.3.6.1.4.1.23.2.1.1.13.1.2 | ColumnadminNotificationStatus | read-write | mandatory | Traps are sent to all primaryContacts who have the corresponding bit set in adminNotificationTrapMask. Traps are sent to backupContacts only if they have the c… |
| 1.3.6.1.4.1.23.2.1.1.13.1.3 | ColumnadminNotificationTrapMask | read-write | mandatory | A bit array specifying which traps the station wishes to receive. Bit Trap 2^0 warmStart 2^1 cableFailure 2^2 reserved 2^3 duplicateIPAddr 2^4 utilizationAlarm… |
| 1.3.6.1.4.1.23.2.1.1.13.1.4 | ColumnadminNotificationConfirmMask | read-write | mandatory | A bit array specifying which traps the station wishes to receive with confirmed delivery. Any bits set must also be set in adminNotificationTrapMask. If a trap… |
| 1.3.6.1.4.1.23.2.1.1.13.1.5 | ColumnadminNotificationTimeout | read-write | mandatory | For traps with confirmed delivery, adminNotificationTimeout specifies the interval (in seconds) between retries. |
| 1.3.6.1.4.1.23.2.1.1.13.1.6 | ColumnadminNotificationRetries | read-write | mandatory | For traps with confirmed delivery, adminNotificationRetries specifies the number of retries that should be attempted before giving up and trying to deliver the… |
| 1.3.6.1.4.1.23.2.1.1.13.1.7 | ColumnadminNotificationBackupIPAddr | read-write | mandatory | For traps with confirmed delivery, adminNotificationBackupIPAddr specifies the IP address of a backup station (also in adminNotificationTable) to be contacted … |
| 1.3.6.1.4.1.23.2.1.1.13.1.8 | ColumnadminNotificationDelete | write-only | mandatory | A write (any value) causes the table entry to be deleted. |
| 1.3.6.1.4.1.23.2.1.1.14 | ScalaradminTrapHandle | not-accessible | mandatory | A unique handle that is generated for each trap issued and that is passed in the trap-PDU along with any other variable bindings. |
| 1.3.6.1.4.1.23.2.1.1.15 | ScalaradminTrapAcknowledge | write-only | mandatory | A trap is acknowledged by writing the value of adminTrapHandle passed in the trap-PDU to adminTrapAcknowledge. |
| 1.3.6.1.4.1.23.2.1.1.16 | ScalaradminDownLoadFile | read-write | mandatory | The name of the executable file to be downloaded from adminDownLoadServer. |
| 1.3.6.1.4.1.23.2.1.1.17 | ScalaradminDownLoadServer | read-write | mandatory | The name of the file server from which to download a new executable image (adminDownLoadFile). |
| 1.3.6.1.4.1.23.2.1.1.18 | ScalaradminDownload | read-write | mandatory | A write to adminDownload of temporaryChange(1) or permanentChange(2) causes the LANtern network monitor to discontinue its normal functions and perform a TFTP … |
| 1.3.6.1.4.1.23.2.1.1.19 | ScalaradminReset | write-only | mandatory | A write to adminReset causes the LANtern network monitor to discontinue its normal functions and commence a restart sequence. The contents of RAM, including al… |
| 1.3.6.1.4.1.23.2.1.1.20 | ScalaradminSerialDataLink | read-write | mandatory | The type of data link encapsulation to be used on the serial line. adminSerialDataLink may be written at any time; however, the change does not take effect unt… |
| 1.3.6.1.4.1.23.2.1.1.21 | ScalaradminSerialIPAddr | read-write | mandatory | The IP address currently in use by the LANtern network monitor on the serial channel. adminSerialIPAddr may be written at any time; however, the change does no… |
| 1.3.6.1.4.1.23.2.1.1.22 | ScalaradminSerialSubnetMask | read-write | mandatory | The subnet mask for the serial channel. adminSerialSubnetMask may be written at any time; however, the change does not take effect until the LANtern network mo… |
| 1.3.6.1.4.1.23.2.1.1.23 | ScalaradminSerialBaudRate | read-write | mandatory | A codification of the baud rate to be used on the serial line for incoming calls or when the line is directly connected. Change does not switch line speed unti… |
| 1.3.6.1.4.1.23.2.1.1.24 | ScalaradminSerialTimeout | read-write | mandatory | Once a phone connection has been established, the LANtern network monitor maintains that connection until either the other end hangs up or adminSerialTimeout s… |
| 1.3.6.1.4.1.23.2.1.1.25 | ScalaradminSerialConnection | read-write | mandatory | The type of connection used by the serial line. adminSerialConnection may be written at any time; however, the change does not take effect until the LANtern ne… |
| 1.3.6.1.4.1.23.2.1.1.26 | ScalaradminSerialFlowControl | read-write | mandatory | The type of flow control used on the serial line. adminSerialFlowControl may be written at any time; however, the change does not take effect until the LANtern… |
| 1.3.6.1.4.1.23.2.1.1.27 | ScalaradminModemControl | read-write | mandatory | A delimited string containing commands to initialize, dial, and hang up the modem. See Section 3.1.2 for more details on the format of this string. adminModemC… |
| 1.3.6.1.4.1.23.2.1.1.28 | ScalaradminModemConnect | read-write | mandatory | A delimited string containing baud rates and modem responses when it connects at particular baud rates. See Section 3.1.2 for more details on the format of thi… |
| 1.3.6.1.4.1.23.2.1.1.29 | ScalaradminModemNoConnect | read-write | mandatory | A delimited string containing baud rates and modem responses when it connects at particular baud rates. See Section 3 for more details on the format of this st… |
| 1.3.6.1.4.1.23.2.1.1.30 | ScalaradminGatewayControl | read-write | mandatory | A switch to enable or disable IP gatewaying between the serial line and the network. See Section 3 for more details on the format of this string. adminGatewayC… |
| 1.3.6.1.4.1.23.2.1.1.31 | TableadminPhoneTable | not-accessible | mandatory | A table that provides information about each possible phone connection that can be made over the serial channel. The table is accessed by adminPhoneIPAddr. A n… |
| 1.3.6.1.4.1.23.2.1.1.31.1 | RowadminPhoneEntry | not-accessible | mandatory | Data for a particular phone connection that can be established over the serial channel. |
| 1.3.6.1.4.1.23.2.1.1.31.1.1 | ColumnadminPhoneIPAddr | read-only | mandatory | The IP address of the machine or IP network (SLIP gateway) at adminPhoneNumber. |
| 1.3.6.1.4.1.23.2.1.1.31.1.2 | ColumnadminPhoneIPMask | read-write | mandatory | The IP subnet mask to be used when communicating over this phone connection. When the value 0.0.0.0 is stored in this variable, the LANtern network monitor ass… |
| 1.3.6.1.4.1.23.2.1.1.31.1.3 | ColumnadminPhoneLocalIPAddr | read-write | mandatory | The IP address the LANtern network monitor uses for its serial port while communicating over this phone connection. |
| 1.3.6.1.4.1.23.2.1.1.31.1.4 | ColumnadminPhoneNumber | read-write | mandatory | The phone number string the modem uses to dial the machine with IP address adminPhoneIPAddr. |
| 1.3.6.1.4.1.23.2.1.1.31.1.5 | ColumnadminPhoneConnectionProtocol | read-write | mandatory | An ASCII string specifying the logon sequence once the phone is connected. |
| 1.3.6.1.4.1.23.2.1.1.31.1.6 | ColumnadminPhoneDelete | write-only | mandatory | A write (any value) causes the table entry to be deleted. |
| 1.3.6.1.4.1.23.2.1.2 | NodelanternEthernet | |||
| 1.3.6.1.4.1.23.2.1.2.1 | ScalareNetworkEvents | read-only | mandatory | The total number of network events (good packets, error packets, and collisions) observed since counter initialization. A network event is any activity on the … |
| 1.3.6.1.4.1.23.2.1.2.2 | ScalareGoodPkts | read-only | mandatory | The total number of legally formed packets received by the network controller since counter initialization. |
| 1.3.6.1.4.1.23.2.1.2.3 | ScalareBroadcastPkts | read-only | mandatory | The total number of good packets with the broadcast address as the destination address. |
| 1.3.6.1.4.1.23.2.1.2.4 | ScalareMulticastPkts | read-only | mandatory | The total number of good packets with a multicast address as the destination address. The broadcast address is not included. |
| 1.3.6.1.4.1.23.2.1.2.5 | ScalareUnicastPkts | read-only | mandatory | The total number of good packets with an individual host address as the destination address. |
| 1.3.6.1.4.1.23.2.1.2.6 | ScalarePkts64to127Octets | read-only | mandatory | The total number of good packets between 64 and 127 octets in length, including the CRC. |
| 1.3.6.1.4.1.23.2.1.2.7 | ScalarePkts128to255Octets | read-only | mandatory | The total number of good packets between 128 and 255 octets in length, including the CRC. |
| 1.3.6.1.4.1.23.2.1.2.8 | ScalarePkts256to511Octets | read-only | mandatory | The total number of good packets between 256 and 511 octets in length, including CRC. |
| 1.3.6.1.4.1.23.2.1.2.9 | ScalarePkts512to1023Octets | read-only | mandatory | The total number of good packets between 512 and 1023 octets in length, including CRC. |
| 1.3.6.1.4.1.23.2.1.2.10 | ScalarePkts1024to1518Octets | read-only | mandatory | The total number of good packets between 1024 and 1518 octets in length, including CRC. |
| 1.3.6.1.4.1.23.2.1.2.11 | ScalareErrors | read-only | mandatory | The total number of errors detected since counter initialization. It is the sum of a CRC/Alignment errors, Oversize errors, Undersize errors, and Jabbers, as d… |
| 1.3.6.1.4.1.23.2.1.2.12 | ScalareCRCAlignErrors | read-only | mandatory | The total number of legal size packets with a bad Frame Check Sequence (FCS) received by the network controller since counter initialization. |
| 1.3.6.1.4.1.23.2.1.2.13 | ScalareUndersizePkts | read-only | mandatory | The total number of undersize packets received by the network controller since counter initialization. An undersize packet is one that is less than 64 octets l… |
| 1.3.6.1.4.1.23.2.1.2.14 | ScalareOversizePkts | read-only | mandatory | The total number of oversize packets received by the network controller since counter initialization. An oversize packet is one that is longer than 1518 octets… |
| 1.3.6.1.4.1.23.2.1.2.15 | ScalareJabbers | read-only | mandatory | The total number of packets longer than 1518 octets with a bad Frame Check Sequence (FCS) received by the network controller since counter initialization. |
| 1.3.6.1.4.1.23.2.1.2.16 | ScalareCollisions | read-only | mandatory | The total number of local collisions observed since counter initialization. A local collision is a collision or other 'signal quality error' event that occurs … |
| 1.3.6.1.4.1.23.2.1.2.17 | ScalareFragments | read-only | mandatory | The total number of packets shorter than 64 octets with a bad Frame Check Sequence (FCS) received by the network controller since counter initialization. |
| 1.3.6.1.4.1.23.2.1.2.18 | ScalareOctets | read-only | mandatory | The total number of octets on the network in good packets. The source/destination address, the type/length field, and the CRC are included. This measurement gi… |
| 1.3.6.1.4.1.23.2.1.2.19 | ScalareTimeUSecs | read-only | mandatory | Time in microseconds. If read in the same PDU as other counters, this can be used to accurately compute statistics over time. |
| 1.3.6.1.4.1.23.2.1.2.20 | ScalareCarrierUSecs | read-only | mandatory | The number of microseconds during which carrier was detected on the cable. This can be used in conjunction with eTimeUSecs to accurately compute network utiliz… |
| 1.3.6.1.4.1.23.2.1.2.21 | ScalareHistoryBuckets | read-only | mandatory | The number of discrete time intervals (or buckets) over which the logged data is saved. This number is a constant. |
| 1.3.6.1.4.1.23.2.1.2.22 | ScalareHistoryInterval | read-write | mandatory | The interval, in seconds, represented by each bucket. eHistoryInterval is stored in nonvolatile RAM. |
| 1.3.6.1.4.1.23.2.1.2.23 | TableeHistoryTable | not-accessible | mandatory | A log of the network events that occurred during each of the preceding eHistoryBuckets intervals of length eHistoryInterval. |
| 1.3.6.1.4.1.23.2.1.2.23.1 | RoweHistoryEntry | not-accessible | mandatory | Each logged counter has the same semantics as the counter with a similar name defined above, except that each counter records only those events that occurred d… |
| 1.3.6.1.4.1.23.2.1.2.23.1.1 | ColumneHistoryNetworkEvents | read-only | mandatory | The number of network events (good packets, error packets, and collisions) observed during the interval. A network event is any activity on the network in whic… |
| 1.3.6.1.4.1.23.2.1.2.23.1.2 | ColumneHistoryGoodPkts | read-only | mandatory | The number of legally formed packets received by the network controller during the interval. |
| 1.3.6.1.4.1.23.2.1.2.23.1.3 | ColumneHistoryBroadcastPkts | read-only | mandatory | The number of good packets with the broadcast address as the destination address received during the interval. |
| 1.3.6.1.4.1.23.2.1.2.23.1.4 | ColumneHistoryMulticastPkts | read-only | mandatory | The number of good packets with a multicast address as the destination address received during the interval. The broadcast address is not included. |
| 1.3.6.1.4.1.23.2.1.2.23.1.5 | ColumneHistoryUnicastPkts | read-only | mandatory | The number of good packets with an individual host address as the destination address received during the interval. |
| 1.3.6.1.4.1.23.2.1.2.23.1.6 | ColumneHistoryPkts64to127Octets | read-only | mandatory | The number of good packets between 64 and 127 octets in length, including the CRC received during the interval. |
| 1.3.6.1.4.1.23.2.1.2.23.1.7 | ColumneHistoryPkts128to255Octets | read-only | mandatory | The number of good packets between 128 and 255 octets in length, including the CRC received during the interval. |
| 1.3.6.1.4.1.23.2.1.2.23.1.8 | ColumneHistoryPkts256to511Octets | read-only | mandatory | The number of good packets between 256 and 511 octets in length, including CRC received during the interval. |
| 1.3.6.1.4.1.23.2.1.2.23.1.9 | ColumneHistoryPkts512to1023Octets | read-only | mandatory | The number of good packets between 512 and 1023 octets in length, including CRC received during the interval. |
| 1.3.6.1.4.1.23.2.1.2.23.1.10 | ColumneHistoryPkts1024to1518Octets | read-only | mandatory | The number of good packets between 1024 and 1518 octets in length, including CRC received during the interval. |
| 1.3.6.1.4.1.23.2.1.2.23.1.11 | ColumneHistoryErrors | read-only | mandatory | The number of errors detected during the interval. It is the sum of a CRC/Alignment errors, Oversize errors, Undersize errors, and Jabbers, as defined below. |
| 1.3.6.1.4.1.23.2.1.2.23.1.12 | ColumneHistoryCRCAlignErrors | read-only | mandatory | The number of legal size packets with a bad Frame Check Sequence (FCS) received by the network controller during the interval. |
| 1.3.6.1.4.1.23.2.1.2.23.1.13 | ColumneHistoryUndersizePkts | read-only | mandatory | The number of undersize packets received by the network controller during the interval. An undersize packet is one that is less than 64 octets long (including … |
| 1.3.6.1.4.1.23.2.1.2.23.1.14 | ColumneHistoryOversizePkts | read-only | mandatory | The number of oversize packets received by the network controller during the interval. An oversize packet is one that is longer than 1518 octets (including CRC… |
| 1.3.6.1.4.1.23.2.1.2.23.1.15 | ColumneHistoryJabbers | read-only | mandatory | The number of packets longer than 1518 octets with a bad Frame Check Sequence (FCS) received by the network controller during the interval. |
| 1.3.6.1.4.1.23.2.1.2.23.1.16 | ColumneHistoryCollisions | read-only | mandatory | The number of local collisions observed during the interval. A local collision is a collision or other 'signal quality error' event that occurs on the segment … |
| 1.3.6.1.4.1.23.2.1.2.23.1.17 | ColumneHistoryFragments | read-only | mandatory | The number of packets shorter than 64 octets with a bad Frame Check Sequence (FCS) received by the network controller during the interval. |
| 1.3.6.1.4.1.23.2.1.2.23.1.18 | ColumneHistoryOctets | read-only | mandatory | The number of octets on the network in good packets during the interval. The source/destination address, the type/length field, and the CRC are included. This … |
| 1.3.6.1.4.1.23.2.1.2.23.1.19 | ColumneHistoryUtilization | read-only | mandatory | The average network utilization during this interval, in tenths of a percent. |
| 1.3.6.1.4.1.23.2.1.2.23.1.20 | ColumneHistoryIntervalStart | read-only | mandatory | The date and time of the start of the interval represented by the data in this bucket. This is the same as eHistoryIntervalEnd of the previous bucket. |
| 1.3.6.1.4.1.23.2.1.2.23.1.21 | ColumneHistoryIntervalEnd | read-only | mandatory | The date and time of the end of the interval represented by the data in this bucket. This is the same as eHistoryIntervalStart of the next bucket. |
| 1.3.6.1.4.1.23.2.1.2.24 | TableeAlarmTable | not-accessible | mandatory | A table of critical gauges for which an alarm is generated, if one exceeds its predetermined thresholds. The table is accessed by gauge type. The user-settable… |
| 1.3.6.1.4.1.23.2.1.2.24.1 | RoweAlarmEntry | not-accessible | mandatory | Parameters for each alarmed gauge. |
| 1.3.6.1.4.1.23.2.1.2.24.1.1 | ColumneAlarmType | read-only | mandatory | Defines the network parameter being monitored by this gauge. percentUtilization: Average percent utilization. percentErrors: Errors as a percentage of total pa… |
| 1.3.6.1.4.1.23.2.1.2.24.1.2 | ColumneAlarmValue | read-only | mandatory | The value, in tenths of one percent, of the monitored network parameter computed over the previous sampling interval. |
| 1.3.6.1.4.1.23.2.1.2.24.1.3 | ColumneAlarmState | read-write | mandatory | If the gauge is enabled, its value is computed and an alarm (trap-PDU) is generated if either of its thresholds is exceeded. Otherwise, its value is not comput… |
| 1.3.6.1.4.1.23.2.1.2.24.1.4 | ColumneAlarmSampleTime | read-write | mandatory | The interval, in seconds, over which eAlarmValue is sampled. eAlarmSampleTime is stored in nonvolatile RAM. |
| 1.3.6.1.4.1.23.2.1.2.24.1.5 | ColumneAlarmMinTraffic | read-write | mandatory | The minimum value the denominator of the alarm equation must achieve during the sample interval before the LANtern network monitor updates eAlarmValue. This ca… |
| 1.3.6.1.4.1.23.2.1.2.24.1.6 | ColumneAlarmLowThreshold | read-write | mandatory | The low threshold for eAlarmValue, in tenths of one percent. eAlarmLowThreshold is stored in nonvolatile RAM. |
| 1.3.6.1.4.1.23.2.1.2.24.1.7 | ColumneAlarmHighThreshold | read-write | mandatory | The high threshold for eAlarmValue, in tenths of one percent. eAlarmHighThreshold is stored in nonvolatile RAM. |
| 1.3.6.1.4.1.23.2.1.2.24.1.8 | ColumneAlarmLowDelta | read-write | mandatory | The delta value used to offset the gauge value when the low threshold is passed, in tenths of one percent. eAlarmLowDelta is stored in nonvolatile RAM. |
| 1.3.6.1.4.1.23.2.1.2.24.1.9 | ColumneAlarmHighDelta | read-write | mandatory | The delta value used to offset the gauge value when the high threshold is passed. eAlarmHighDelta is stored in nonvolatile RAM. |
| 1.3.6.1.4.1.23.2.1.2.24.1.10 | ColumneAlarmLowWaterMark | read-write | mandatory | The lowest value seen for eAlarmValue, in tenths of one percent. This can be reset by writing to eAlarmLowWaterMark. The value written is ignored, and eAlarmLo… |
| 1.3.6.1.4.1.23.2.1.2.24.1.11 | ColumneAlarmHighWaterMark | read-write | mandatory | The highest value seen for eAlarmValue, in tenths of one percent. This can be reset by writing to eAlarmHighWaterMark. The value written is ignored, and eAlarm… |
| 1.3.6.1.4.1.23.2.1.2.24.1.12 | ColumneAlarmLowSetTime | read-only | mandatory | The date and time eAlarmLowWaterMark was last set. This value is NULL until the first time eAlarmLowWaterMark is set. |
| 1.3.6.1.4.1.23.2.1.2.24.1.13 | ColumneAlarmHighSetTime | read-only | mandatory | The date and time eAlarmHighWaterMark was last set. This value is NULL until the first time eAlarmHighWaterMark is set. |
| 1.3.6.1.4.1.23.2.1.2.25 | ScalareHostNewHostAlarm | read-write | mandatory | If enabled, the LANtern network monitor generates a newHost trap whenever a new host first transmits on the network segment. Note that eHostNewHostAlarm is NOT… |
| 1.3.6.1.4.1.23.2.1.2.26 | ScalareHostTableEntries | read-only | mandatory | The number of entries currently in eHostTable and eHostTTable. |
| 1.3.6.1.4.1.23.2.1.2.27 | ScalareHostPurge | read-write | mandatory | Writing a date and time to eHostPurge causes the LANtern network monitor to purge all host table entries eHostTable where the date and time of both the most re… |
| 1.3.6.1.4.1.23.2.1.2.28 | TableeHostTable | not-accessible | mandatory | Statistical data for each host seen on the network, accessed by MAC address. Entries may be 'preloaded' into the table by writing to eHostControl for the appro… |
| 1.3.6.1.4.1.23.2.1.2.28.1 | RoweHostEntry | not-accessible | mandatory | Statistical data for each host seen on the network, accessed by eHostAddress. |
| 1.3.6.1.4.1.23.2.1.2.28.1.1 | ColumneHostAddress | read-only | mandatory | The MAC layer physical address of the host. |
| 1.3.6.1.4.1.23.2.1.2.28.1.2 | ColumneHostInPkts | read-only | mandatory | The total number of good packets transmitted to this address. |
| 1.3.6.1.4.1.23.2.1.2.28.1.3 | ColumneHostOutPkts | read-only | mandatory | The total number of good packets transmitted by this host. |
| 1.3.6.1.4.1.23.2.1.2.28.1.4 | ColumneHostInOctets | read-only | mandatory | The total number of octets in good packets transmitted to this address. |
| 1.3.6.1.4.1.23.2.1.2.28.1.5 | ColumneHostOutOctets | read-only | mandatory | The total number of octets in good packets transmitted by this host. |
| 1.3.6.1.4.1.23.2.1.2.28.1.6 | ColumneHostInErrors | read-only | mandatory | The total number of error (CRC, undersize, or oversize) packets transmitted to this address. |
| 1.3.6.1.4.1.23.2.1.2.28.1.7 | ColumneHostOutErrors | read-only | mandatory | The total number of error (CRC, undersize, or oversize) packets transmitted by this host. |
| 1.3.6.1.4.1.23.2.1.2.28.1.8 | ColumneHostProtocols | read-only | mandatory | A bit array where each bit indicates a protocol that was seen in a packet transmitted by that host. The protocols currently monitored are: Bit Protocol 2^0 Unr… |
| 1.3.6.1.4.1.23.2.1.2.28.1.9 | ColumneHostFirstTransmit | read-only | mandatory | The date and time of the first good transmission by this host. If the host has not transmitted, this value is 0 |
| 1.3.6.1.4.1.23.2.1.2.28.1.10 | ColumneHostLastTransmit | read-only | mandatory | The date and time of the most recent transmission by this host. If the host has not transmitted, this value is 0 |
| 1.3.6.1.4.1.23.2.1.2.28.1.11 | ColumneHostLastReceive | read-only | mandatory | The data and time of the most recent transmission to this address. |
| 1.3.6.1.4.1.23.2.1.2.28.1.12 | ColumneHostControl | read-write | mandatory | A collection of control bits and bit fields. These fields are grouped into one object to reduce network traffic (especially over the serial line) during startu… |
| 1.3.6.1.4.1.23.2.1.2.28.1.13 | ColumneHostDelete | write-only | mandatory | An entry may be deleted from eHostTable by writing (any value) to eHostDelete. Note that this overrides the purge disable flag in eHostControl. Any entries in … |
| 1.3.6.1.4.1.23.2.1.2.29 | TableeHostTTable | not-accessible | mandatory | Statistical data for each host that has transmitted on the network; accessed by eHostTFirstTransmit (and an ordinal number to resolve ambiguities). |
| 1.3.6.1.4.1.23.2.1.2.29.1 | RoweHostTEntry | not-accessible | mandatory | The contents are identical to those described for eHostTable above except that the access for eHostTControl is read-only for all communities. The table is acce… |
| 1.3.6.1.4.1.23.2.1.2.29.1.1 | ColumneHostTAddress | read-only | mandatory | The MAC layer physical address of the host. |
| 1.3.6.1.4.1.23.2.1.2.29.1.2 | ColumneHostTInPkts | read-only | mandatory | The total number of good packets transmitted to this address. |
| 1.3.6.1.4.1.23.2.1.2.29.1.3 | ColumneHostTOutPkts | read-only | mandatory | The total number of good packets transmitted by this host. |
| 1.3.6.1.4.1.23.2.1.2.29.1.4 | ColumneHostTInOctets | read-only | mandatory | The total number of octets in good packets transmitted to this address. |
| 1.3.6.1.4.1.23.2.1.2.29.1.5 | ColumneHostTOutOctets | read-only | mandatory | The total number of octets in good packets transmitted by this host. |
| 1.3.6.1.4.1.23.2.1.2.29.1.6 | ColumneHostTInErrors | read-only | mandatory | The total number of error (CRC, undersize, or oversize) packets transmitted to this address. |
| 1.3.6.1.4.1.23.2.1.2.29.1.7 | ColumneHostTOutErrors | read-only | mandatory | The total number of error (CRC, undersize, or oversize) packets transmitted by this host. |
| 1.3.6.1.4.1.23.2.1.2.29.1.8 | ColumneHostTProtocols | read-only | mandatory | A bit array where each bit indicates a protocol that was seen in a packet transmitted by that host. The protocols currently monitored are: Bit Protocol 2^0 Unr… |
| 1.3.6.1.4.1.23.2.1.2.29.1.9 | ColumneHostTFirstTransmit | read-only | mandatory | The date and time of the first good transmission by this host. If the host has not transmitted, this value is 0 |
| 1.3.6.1.4.1.23.2.1.2.29.1.10 | ColumneHostTLastTransmit | read-only | mandatory | The date and time of the most recent transmission by this host. If the host has not transmitted, this value is 0 |
| 1.3.6.1.4.1.23.2.1.2.29.1.11 | ColumneHostTLastReceive | read-only | mandatory | The data and time of the most recent transmission to this address. |
| 1.3.6.1.4.1.23.2.1.2.29.1.12 | ColumneHostTControl | read-only | mandatory | A collection of control bits and bit fields. These fields are grouped into one object to reduce network traffic (especially over the serial line) during startu… |
| 1.3.6.1.4.1.23.2.1.2.30 | ScalareMatrixTableEntries | read-only | mandatory | The number of entries currently in eMatrixSDTable and eMatrixDSTable. |
| 1.3.6.1.4.1.23.2.1.2.31 | ScalareMatrixPurge | read-write | mandatory | Writing a date and time to eMatrixPurge causes the LANtern network monitor to purge all matrix (eMatrixSDTable and eMatrixDSTable) table entries where the date… |
| 1.3.6.1.4.1.23.2.1.2.32 | TableeMatrixSDTable | not-accessible | mandatory | A table of network traffic sent from one particular source host to one particular destination host. A particular object instance is accessed by appending the s… |
| 1.3.6.1.4.1.23.2.1.2.32.1 | RoweMatrixSDEntry | not-accessible | mandatory | The statistics for traffic in a particular direction between two hosts on the network. |
| 1.3.6.1.4.1.23.2.1.2.32.1.1 | ColumneMatrixSDSourceAddress | read-only | mandatory | The MAC layer physical address of the source host. |
| 1.3.6.1.4.1.23.2.1.2.32.1.2 | ColumneMatrixSDDestAddress | read-only | mandatory | The MAC layer physical address of the destination host. |
| 1.3.6.1.4.1.23.2.1.2.32.1.3 | ColumneMatrixSDPkts | read-only | mandatory | The number of good packets sent from eMatrixSDSourceAddress to eMatrixSDDestAddress. |
| 1.3.6.1.4.1.23.2.1.2.32.1.4 | ColumneMatrixSDOctets | read-only | mandatory | The number of octets in good packets sent from eMatrixSDSourceAddress to eMatrixSDDestAddress. |
| 1.3.6.1.4.1.23.2.1.2.32.1.5 | ColumneMatrixSDErrors | read-only | mandatory | The number of error (CRC/align/undersize/oversize) packets sent from eMatrixSDSourceAddress to eMatrixSDDestAddress. |
| 1.3.6.1.4.1.23.2.1.2.32.1.6 | ColumneMatrixSDProtocols | read-only | mandatory | A bit array where each bit indicates a protocol that was seen in a packet sent from eMatrixSDSourceAddress to eMatrixSDDestAddress. The protocols currently mon… |
| 1.3.6.1.4.1.23.2.1.2.32.1.7 | ColumneMatrixSDFirstTransmit | read-only | mandatory | The date and time the first transmission from eMatrixSDSourceAddress to eMatrixSDDestAddress. |
| 1.3.6.1.4.1.23.2.1.2.32.1.8 | ColumneMatrixSDLastTransmit | read-only | mandatory | The date and time of the most recent transmission from eMatrixSDSourceAddress to eMatrixSDDestAddress. |
| 1.3.6.1.4.1.23.2.1.2.32.1.9 | ColumneMatrixSDDelete | write-only | mandatory | A write (any value) causes the table entry to be deleted. |
| 1.3.6.1.4.1.23.2.1.2.33 | TableeMatrixDSTable | not-accessible | mandatory | A table of network traffic sent from one particular source host to one particular destination host. A particular object instance is accessed by appending the d… |
| 1.3.6.1.4.1.23.2.1.2.33.1 | RoweMatrixDSEntry | not-accessible | mandatory | The contents of the table are identical to those described above for eMatrixSDTable. |
| 1.3.6.1.4.1.23.2.1.2.33.1.1 | ColumneMatrixDSSourceAddress | read-only | mandatory | The MAC layer physical address of the source host. |
| 1.3.6.1.4.1.23.2.1.2.33.1.2 | ColumneMatrixDSDestAddress | read-only | mandatory | |
| 1.3.6.1.4.1.23.2.1.2.33.1.3 | ColumneMatrixDSPkts | read-only | mandatory | The number of good packets sent from eMatrixDSSourceAddress to eMatrixDSDestAddress. |
| 1.3.6.1.4.1.23.2.1.2.33.1.4 | ColumneMatrixDSOctets | read-only | mandatory | The number of octets in good packets sent from eMatrixDSSourceAddress to eMatrixDSDestAddress. |
| 1.3.6.1.4.1.23.2.1.2.33.1.5 | ColumneMatrixDSErrors | read-only | mandatory | The number of error (CRC/align/undersize/oversize) packets sent from eMatrixDSSourceAddress to eMatrixDSDestAddress. |
| 1.3.6.1.4.1.23.2.1.2.33.1.6 | ColumneMatrixDSProtocols | read-only | mandatory | A bit array where each bit indicates a protocol that was seen in a packet sent from eMatrixDSSourceAddress to eMatrixDSDestAng defining the time zone of thee p… |
| 1.3.6.1.4.1.23.2.1.2.33.1.7 | ColumneMatrixDSFirstTransmit | read-only | mandatory | The date and time the first transmission from eMatrixDSSourceAddress to eMatrixDSDestAddress. |
| 1.3.6.1.4.1.23.2.1.2.33.1.8 | ColumneMatrixDSLastTransmit | read-only | mandatory | The date and time of the most recent transmission from eMatrixDSSourceAddress to eMatrixDSDestAddress. |
| 1.3.6.1.4.1.23.2.1.2.33.1.9 | ColumneMatrixDSDelete | write-only | mandatory | A write (any value) causes the table entry to be deleted. |
| 1.3.6.1.4.1.23.2.1.2.34 | ScalareMediaCheckInterval | read-write | mandatory | The LANtern network monitor performs a periodic cable check every eMediaCheckInterval seconds. If eMediaCheckInterval is zero, periodic cable checks are not pe… |
| 1.3.6.1.4.1.23.2.1.2.35 | ScalareMediaStatus | read-only | mandatory | Reading eMediaStatus returns the most recent cable check, automatic or manual. Writing any value causby the LANtern network . This object is also passed in the… |
| 1.3.6.1.4.1.23.2.1.2.37 | ScalareHostLimit | read-only | mandatory | The maximum number of unicast addresses which the LANtern host table holds. A value of 0 indicates that there is no limit other than memory constraints. The va… |
| 1.3.6.1.4.1.23.2.1.2.38 | ScalareOnSegmentPkts | read-only | mandatory | The count of the number of packets which were transmitted between hosts on the same segment as the LANtern. |
| 1.3.6.1.4.1.23.2.1.2.39 | ScalareOnSegmentOctets | read-only | mandatory | The count of the number of octets in packets which were transmitted between hosts on the same segment as the LANtern. |
| 1.3.6.1.4.1.23.2.1.2.40 | ScalareDepartingPkts | read-only | mandatory | The count of the number of packets which were transmitted by hosts on the same segment as the LANtern to hosts on other segments. |
| 1.3.6.1.4.1.23.2.1.2.41 | ScalareDepartingOctets | read-only | mandatory | The count of the number of octets in packets which were transmitted by hosts on the same segment as the LANtern to hosts on other segments. |
| 1.3.6.1.4.1.23.2.1.2.42 | ScalareArrivingPkts | read-only | mandatory | The count of the number of packets which were transmitted by hosts on other segments to hosts on the same segment as the LANtern. |
| 1.3.6.1.4.1.23.2.1.2.43 | ScalareArrivingOctets | read-only | mandatory | The count of the number of octets in packets which were transmitted by hosts on other segments to hosts on the same segment as the LANtern. |
| 1.3.6.1.4.1.23.2.1.2.44 | ScalareThruPkts | read-only | mandatory | The count of the number of packets seen on the LANtern's segment which were transmitted between hosts which are not on the LANtern's segment. |
| 1.3.6.1.4.1.23.2.1.2.45 | ScalareThruOctets | read-only | mandatory | The count of the number of octets in packets seen on the LANtern's segment which were transmitted between hosts which are not on the LANtern's segment. |
| 1.3.6.1.4.1.23.2.1.2.46 | ScalareHostDeletes | read-only | mandatory | A count of the number of hosts which have been deleted since the LANtern was powered on. |
| 1.3.6.1.4.1.23.2.1.2.47 | TableeHostOTable | not-accessible | mandatory | Statistical data for each host that has transmitted on the network; accessed by eHostOOrderIndex. This table exists to permit rapid downloading of the host tab… |
| 1.3.6.1.4.1.23.2.1.2.47.1 | RoweHostOEntry | not-accessible | mandatory | The contents are identical to those described for eHostTable above except that the access for eHostOControl is read-only for all communities and eHostOOrderInd… |
| 1.3.6.1.4.1.23.2.1.2.47.1.1 | ColumneHostOAddress | read-only | mandatory | The MAC layer physical address of the host. |
| 1.3.6.1.4.1.23.2.1.2.47.1.2 | ColumneHostOInPkts | read-only | mandatory | The total number of good packets transmitted to this address. |
| 1.3.6.1.4.1.23.2.1.2.47.1.3 | ColumneHostOOutPkts | read-only | mandatory | The total number of good packets transmitted by this host. |
| 1.3.6.1.4.1.23.2.1.2.47.1.4 | ColumneHostOInOctets | read-only | mandatory | The total number of octets in good packets transmitted to this address. |
| 1.3.6.1.4.1.23.2.1.2.47.1.5 | ColumneHostOOutOctets | read-only | mandatory | The total number of octets in good packets transmitted by this host. |
| 1.3.6.1.4.1.23.2.1.2.47.1.6 | ColumneHostOInErrors | read-only | mandatory | The total number of error (CRC, undersize, or oversize) packets transmitted to this address. |
| 1.3.6.1.4.1.23.2.1.2.47.1.7 | ColumneHostOOutErrors | read-only | mandatory | The total number of error (CRC, undersize, or oversize) packets transmitted by this host. |
| 1.3.6.1.4.1.23.2.1.2.47.1.8 | ColumneHostOProtocols | read-only | mandatory | A bit array where each bit indicates a protocol that was seen in a packet transmitted by that host. The protocols currently monitored are: Bit Protocol 2^0 Unr… |
| 1.3.6.1.4.1.23.2.1.2.47.1.9 | ColumneHostOFirstTransmit | read-only | mandatory | The date and time of the first good transmission by this host. If the host has not transmitted, this value is 0 |
| 1.3.6.1.4.1.23.2.1.2.47.1.10 | ColumneHostOLastTransmit | read-only | mandatory | The date and time of the most recent transmission by this host. If the host has not transmitted, this value is 0 |
| 1.3.6.1.4.1.23.2.1.2.47.1.11 | ColumneHostOLastReceive | read-only | mandatory | The data and time of the most recent transmission to this address. |
| 1.3.6.1.4.1.23.2.1.2.47.1.12 | ColumneHostOControl | read-only | mandatory | A collection of control bits and bit fields. These fields are grouped into one object to reduce network traffic (especially over the serial line) during startu… |
| 1.3.6.1.4.1.23.2.1.2.47.1.13 | ColumneHostOOrderIndex | read-only | mandatory | A (dense) ordinal that uniquely defines an entry in the eHostOTable table. |
| 1.3.6.1.4.1.23.2.1.3 | NodelanternTokenRing | |||
| 1.3.6.1.4.1.23.2.1.4 | NodelanternIp | |||
| 1.3.6.1.4.1.23.2.1.4.1 | ScalaripPingTarget | write-only | mandatory | Writing an IP address to ipPingTarget causes the LANtern network monitor to ping that host (using ICMP Echo). When the LANtern network monitor receives the ech… |
| 1.3.6.1.4.1.23.2.1.4.2 | ScalaripPingDuration | not-accessible | mandatory | The elapsed time between the LANtern network monitor's issuance of the Ping and its receipt of the response. This data is passed with the pingNotification trap… |
| 1.3.6.1.4.1.23.2.1.4.3 | ScalaripDupeCheck | read-write | mandatory | Enables or disables duplicate IP address checking. ipDupeCheck may be written at any time; however, the change does not take effect until the LANtern network m… |
| 1.3.6.1.4.1.23.2.1.4.4 | TableipDupeTable | not-accessible | mandatory | Table of active duplicate IP address alarms, accessed by IP address. |
| 1.3.6.1.4.1.23.2.1.4.4.1 | RowipDupeEntry | not-accessible | mandatory | Data pertinent to the duplicate IP address alarm. |
| 1.3.6.1.4.1.23.2.1.4.4.1.1 | ColumnipDupeIPAddr | read-only | mandatory | The IP address that was observed being used by more than one host. |
| 1.3.6.1.4.1.23.2.1.4.4.1.2 | ColumnipDupeGoodMACAddr | read-only | mandatory | The physical network address of the host that is authorized to use the IP address. Initially, this is the host that was first seen to use the IP address. Once … |
| 1.3.6.1.4.1.23.2.1.4.4.1.3 | ColumnipDupeBadMACAddr | read-only | mandatory | The physical network address of the host that is erroneously using the IP address. |
| 1.3.6.1.4.1.23.2.1.4.4.1.4 | ColumnipDupeTime | read-only | mandatory | The date and time the duplicate usage of the IP address was detected. |
| 1.3.6.1.4.1.23.2.1.4.4.1.5 | ColumnipDupeClear | write-only | mandatory | When the condition causing the alarm has been fixed, the administrator should clear the alarm by writing to alarmDupIpClear. Either of the two MAC addresses ca… |
| 1.3.6.1.4.1.23.2.1.4.5 | TableipMACToIPTable | not-accessible | mandatory | A table containing mappings from physical media addresses to IP addresses; accessed by ipMACToIPMACAddr. ipMACToIPIPAddr is also required as a secondary index … |
| 1.3.6.1.4.1.23.2.1.4.5.1 | RowipMACToIPEntry | not-accessible | mandatory | The mapping from a physical media address to an IP address. |
| 1.3.6.1.4.1.23.2.1.4.5.1.1 | ColumnipMACToIPMACAddr | read-only | mandatory | The physical media address. |
| 1.3.6.1.4.1.23.2.1.4.5.1.2 | ColumnipMACToIPIPAddr | read-only | mandatory | The IP address. |
| 1.3.6.1.4.1.23.2.1.4.5.1.3 | ColumnipMACToIPDelete | write-only | mandatory | An entry may be deleted from ipMACToIPTable by writing (any value) to ipMACToIPDelete. This also deletes the entry in the ipDupeTable for the same IP address i… |
| 1.3.6.1.4.1.23.2.1.5 | Nodelantern802dot2 | |||
| 1.3.6.1.4.1.23.2.1.5.1 | Scalarieee8022TestTarget | write-only | mandatory | Writing an ethernet address to ieee8022TestTarget causes the LANtern to send an 802.2 Test packet to that address. |
| 1.3.6.1.4.1.23.2.1.6 | NodelanternIpx | |||
| 1.3.6.1.4.1.23.2.1.6.1 | ScalaripxDiagnosticTarget | write-only | mandatory | Writing an ethernet address to ipxDiagnosticTarget causes the LANtern to send two diagnostic packets, one in ethernet frame format, and the other in 802.3 fram… |
| 1.3.6.1.4.1.23.2.1.10 | NodelanternProtocols | |||
| 1.3.6.1.4.1.23.2.1.10.1 | ScalarprotoUnknownPkts | read-only | mandatory | The count of packets observed with an unknown protocol. |
| 1.3.6.1.4.1.23.2.1.10.2 | ScalarprotoUnknownOctets | read-only | mandatory | The count of octets in packets observed with an unknown protocol. |
| 1.3.6.1.4.1.23.2.1.10.3 | ScalarprotoTCPIPPkts | read-only | mandatory | The count of packets observed with a protocol from the TCP/IP suite (IP, ARP, and RARP). |
| 1.3.6.1.4.1.23.2.1.10.4 | ScalarprotoTCPIPOctets | read-only | mandatory | The count of octets in packets observed with a protocol from the TCP/IP suite (IP, ARP, and RARP). |
| 1.3.6.1.4.1.23.2.1.10.5 | ScalarprotoISOPkts | read-only | mandatory | The count of packets observed with a protocol from the ISO suite. |
| 1.3.6.1.4.1.23.2.1.10.6 | ScalarprotoISOOctets | read-only | mandatory | The count of octets in packets observed with a protocol from the ISO suite. |
| 1.3.6.1.4.1.23.2.1.10.7 | ScalarprotoDECPkts | read-only | mandatory | The count of packets observed with a protocol from the Digital Equipment Corporation protocol suite. |
| 1.3.6.1.4.1.23.2.1.10.8 | ScalarprotoDECOctets | read-only | mandatory | The count of octets in packets observed with a protocol from the Digital Equipment Corporation protocol suite. |
| 1.3.6.1.4.1.23.2.1.10.9 | ScalarprotoNetWarePkts | read-only | mandatory | The count of packets observed with a protocol from the NetWare suite. |
| 1.3.6.1.4.1.23.2.1.10.10 | ScalarprotoNetWareOctets | read-only | mandatory | The count of octets in packets observed with a protocol from the NetWare suite. |
| 1.3.6.1.4.1.23.2.1.10.11 | ScalarprotoAppleTalkPkts | read-only | mandatory | The count of packets observed with a protocol from the AppleTalk suite. |
| 1.3.6.1.4.1.23.2.1.10.12 | ScalarprotoAppleTalkOctets | read-only | mandatory | The count of octets in packets observed with a protocol from the AppleTalk suite. |
| 1.3.6.1.4.1.23.2.1.10.13 | ScalarprotoXNSPkts | read-only | mandatory | The count of packets observed with a protocol from the XNS suite. |
| 1.3.6.1.4.1.23.2.1.10.14 | ScalarprotoXNSOctets | read-only | mandatory | The count of octets in packets observed with a protocol from the XNS suite. |
| 1.3.6.1.4.1.23.2.1.10.15 | ScalarprotoSNAPkts | read-only | mandatory | The count of packets observed with a protocol from the SNA suite. |
| 1.3.6.1.4.1.23.2.1.10.16 | ScalarprotoSNAOctets | read-only | mandatory | The count of octets in packets observed with a protocol from the SNA suite. |
| 1.3.6.1.4.1.23.2.1.10.17 | ScalarprotoVINESPkts | read-only | mandatory | The count of packets observed with a protocol from the Banyan VINES suite. |
| 1.3.6.1.4.1.23.2.1.10.18 | ScalarprotoVINESOctets | read-only | mandatory | The count of octets in packets observed with a protocol from the Banyan VINES suite. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| DisplayString | OCTET STRING | ||
| PhysAddress | OCTET STRING | ||
| Seconds | INTEGER | ||
| Time | INTEGER |