NNCEXTSPVC-MIB
215 objects
This module contains Alcatel CID's proprietary MIB definition for managing Soft Permanent Virtual Connections (SPVCs). This MIB supports the creation, modification, query, and deletion of SPVCs (Soft Permanent Virtual Connections), on Cell Relay (ATM), Frame Relay, and Circuit Emulation endpoints. For Cell Relay-based endpoints, Permanent Virtual Path Connection (PVPC) and Permanent Virtual Channel Connection (PVCC) are supported, while SPVCCs are supported on Frame Relay and Circuit Emulation endpoints. Cell Relay SPVCs, Frame Relay SPVCs and Circuit Emulation SPVCs are supported in this MIB. SPVCs with any other service types are not supported at this point. For SPVCs interworking across different endpoint types, CR to FR, FR to CR, CR to CE, CE to CR connections are supported. CE to FR or FR to CE are not suppported. Operator directed routing for SPVC connections is not supported at this point. To create an SPVC, the required MIB objects from the destination table must be configured and sent to the destination endpoint. Next, the MIB objects from the source endpoint table (based on the endpoint type and SPVC type - either nncCrSpvpcTable, nncCrSpvccTable, nncFrSpvcTable, or nncCeSpvcTable) are configured and sent to the source endpoint. Assuming a PDU with a RowStatus of 'createAndGo' or 'Active' has been received, if the adminStatus of the SPVC is set to 'enabled', the SPVC will be connected; if the adminStatus of the SPVC is set to 'disabled', the SPVC will be configured but not connected. SPVC creation SET-REQuests can be sent two ways: using a RowStatus value of 'createAndGo', or using multiple SET-REQs using RowStatus values of 'createAndWait' and 'active'. Creating an SPVC using rowStatus=createAndWait(5) In the case of multiple SET-REQs, the RowStatus is set to createAndWait(5) for all but the last SET-REQ, and set to active(1) for the last SET-REQ. The SPVC is configured only after the last PDU (with RowStatus as 'active') is received. Creating an SPVC using rowStatus=createAndGo(4) In the other case, all required MIB objects can fit in one SET-REQ. If using only one SET-REQ, the RowStatus should be set to createAndGo(4). In both cases, default values for MIB objects will be used wherever possible. To delete an SPVC, the correct table objects must be sent to both the destination endpoint and the source endpoint for the given SPVC, using the correct index, and setting the rowStatus to 'destroy'. This will delete the specified SPVC. Some abreviations: abr/ABR/Abr: Available Bit Rate Bwd: Backward. For traffice descriptors from destination endpoint to source endpoint (receiving traffic) cbr/CBR/Cbr: Constant Bit Rate Dst: Destination endpoint Fwd: Forward. For traffic descriptors from source endpoint to destination endpoint (transmitting traffic) nt-vbr/nrtvbr/NRT-VBR: Non-Real-Time Variable Bit Rate Src: Source endpoint Targ: Target. For the destination endpoint info in source endpoint table ubr/UBR/Ubr: Unspecified Bit Rate
Imported Objects
| ATM-MIB | atmVclVci atmVclVpi atmVplVpi |
| IF-MIB | ifIndex |
| NNCGNI0001-SMI | nncExtensions |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE |
| SNMPv2-TC | RowStatus TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.123.3.82 | IdentitynncExtSpvc | This module contains Alcatel CID's proprietary MIB definition for managing Soft Permanent Virtual Connections (SPVCs). This MIB supports the creation, modifica… | ||
| 1.3.6.1.4.1.123.3.82.1 | NodenncExtSpvcObjects | |||
| 1.3.6.1.4.1.123.3.82.1.1 | TablenncCrSpvpcTable | not-accessible | current | nncCrSpvpcTable contains all the objects sent to a source endpoint that are used to create, modify, query and delete SPVC connections. |
| 1.3.6.1.4.1.123.3.82.1.1.1 | RownncCrSpvpcTableEntry | not-accessible | current | An entry of nncCrSpvpcTable |
| 1.3.6.1.4.1.123.3.82.1.1.1.1 | ColumnnncCrSpvpcServiceCategory | read-create | current | This object is used to set the traffic service category. This object is dependent on the value specified in nncCrSpvpcTrafficDescriptor |
| 1.3.6.1.4.1.123.3.82.1.1.1.2 | ColumnnncCrSpvpcTargEpAddr | read-create | current | This object is used to specify the 20 byte AESA address for the target endpoint. The address map is as the following: Byte\Bit 8 7 6 5 4 3 2 1 1-13 byte | 13-b… |
| 1.3.6.1.4.1.123.3.82.1.1.1.3 | ColumnnncCrSpvpcTargVpi | read-create | current | This object contains the virtual path identifier (VPI) value for the target endpoint. Range: 0 - 4095 |
| 1.3.6.1.4.1.123.3.82.1.1.1.4 | ColumnnncCrSpvpcAdminStatus | read-create | current | This object accepts two values, enabled (1), and disabled (2). When the value is disabled, the SPVC is not connected. When enabled, the SPVC is connected when … |
| 1.3.6.1.4.1.123.3.82.1.1.1.5 | ColumnnncCrSpvpcPriority | read-create | current | This object is used to set the priority for a SPVC connection request. It ranges between 1-16, with the following values: Best Priority = 1 Default Priority = … |
| 1.3.6.1.4.1.123.3.82.1.1.1.6 | ColumnnncCrSpvpcMaxAdminWeight | read-create | current | This object is used to set a cost threshold for an SPVC connection. If the total cost of all VPCs exceeds this weight value for a given path, this SPVC will ch… |
| 1.3.6.1.4.1.123.3.82.1.1.1.7 | ColumnnncCrSpvpcOperation | read-create | current | This object is used to request a reroute operation. Querying this object will not provide any useful information. |
| 1.3.6.1.4.1.123.3.82.1.1.1.8 | ColumnnncCrSpvpcCallStatus | read-only | current | This read-only object is used to query the state of a particular SPVC. SPVCs that are connected and operational will return a value of 'connected', while those… |
| 1.3.6.1.4.1.123.3.82.1.1.1.9 | ColumnnncCrSpvpcLocRerouteConfig | read-create | current | This object is used to configure the 'reroute on loss of continuity' feature using OAM-CC cells. It can be configured for either the UNI side or the NNI side, … |
| 1.3.6.1.4.1.123.3.82.1.1.1.10 | ColumnnncCrSpvpcFwdAbrDynTrfcIcr | read-create | current | ABR dynamic traffic descriptor's Initial Cell (Information) Rate for the forward direction. Range: 0 - 2488320 Kb/s |
| 1.3.6.1.4.1.123.3.82.1.1.1.11 | ColumnnncCrSpvpcFwdAbrDynTrfcRif | read-create | current | ABR traffic Rate Increase Factor for the forward direction. Value is expressed as the -power of 2. Range: 0 - 9 |
| 1.3.6.1.4.1.123.3.82.1.1.1.12 | ColumnnncCrSpvpcFwdAbrDynTrfcRdf | read-create | current | ABR traffic Rate Decrease Factor descriptor for the forward direction. Value is expressed as the -power of 2 Range: 0 - 9 |
| 1.3.6.1.4.1.123.3.82.1.1.1.13 | ColumnnncCrSpvpcBwdAbrDynTrfcIcr | read-create | current | ABR dynamic traffic descriptor's Initial Cell Rate for the destination endpoint. Range: 0 - 2488320 Kb/s |
| 1.3.6.1.4.1.123.3.82.1.1.1.14 | ColumnnncCrSpvpcBwdAbrDynTrfcRif | read-create | current | ABR traffic Rate Increase Factor for the backward direction. Value is expressed as the -power of 2. Range: 0 - 9 |
| 1.3.6.1.4.1.123.3.82.1.1.1.15 | ColumnnncCrSpvpcBwdAbrDynTrfcRdf | read-create | current | ABR traffic Rate Decrease Factor descriptor for the backward direction. Value is expressed as the -power of 2 Range: 0 - 9 |
| 1.3.6.1.4.1.123.3.82.1.1.1.16 | ColumnnncCrSpvpcSrcBillingFlag | read-create | current | Billing Configuration for the source endpoint |
| 1.3.6.1.4.1.123.3.82.1.1.1.17 | ColumnnncCrSpvpcFwdTmTrafficDescriptor | read-create | current | This object contains the traffic descriptor for the SPVC. Tag All (1) (UBR using 2k/12k fabric only) P_0+1 (2) (CBR only) P_0+1/S_0+1 (3) (NRT/RT-VBR only) P_0… |
| 1.3.6.1.4.1.123.3.82.1.1.1.18 | ColumnnncCrSpvpcFwdTmPolicingOption | read-create | current | Policing Option for an SPVPC. tag is supported only on rt-VBR/nrt-VBR connections that use the P_0+1/S_0 traffic descriptor |
| 1.3.6.1.4.1.123.3.82.1.1.1.19 | ColumnnncCrSpvpcFwdTmBucketOneRate | read-create | current | This object is for peak cell rate (PCR), the cell rate which the source may never exceed. It is used to determine which cells are 'excess'. Measured in Kb/s. R… |
| 1.3.6.1.4.1.123.3.82.1.1.1.20 | ColumnnncCrSpvpcFwdTmBucketOneCdvt | read-create | current | This object is used to set cell delay variation tolerance (CDVT) for one endpoint, measured in microseconds. Range: 1 - 190,000 microseconds |
| 1.3.6.1.4.1.123.3.82.1.1.1.21 | ColumnnncCrSpvpcFwdTmBucketTwoRate | read-create | current | SIR_0p, SIR_0+1p or MIR_0+1p. This parameter holds the sustained information rate for VBR traffic, and the minimum information rate for ABR/UBR traffic. Range:… |
| 1.3.6.1.4.1.123.3.82.1.1.1.22 | ColumnnncCrSpvpcFwdTmBucketTwoMbs | read-create | current | This object is for the maximum burst size, in cells, for SIR_0p or SIR_0+1p (nrtVbr and rtVbr only). Range: 1 - 10000 cells |
| 1.3.6.1.4.1.123.3.82.1.1.1.23 | ColumnnncCrSpvpcFwdTmCdv | read-create | current | This value is to set the cell delay variation (CDV) between two endpoints to support the rt-VBR service category. Range: 250-10000 microseconds |
| 1.3.6.1.4.1.123.3.82.1.1.1.24 | ColumnnncCrSpvpcFwdTmClr | read-create | current | The object is to set the cell loss ratio (CLR) between two SPVC endpoints when using the nrt-VBR service category. Value set as 1.0e-# |
| 1.3.6.1.4.1.123.3.82.1.1.1.25 | ColumnnncCrSpvpcBwdTmTrafficDescriptor | read-create | current | This object contains the traffic descriptor for the SPVC. Tag All (1) (UBR using 2k/12k fabric only) P_0+1 (2) (CBR only) P_0+1/S_0+1 (3) (NRT/RT-VBR only) P_0… |
| 1.3.6.1.4.1.123.3.82.1.1.1.26 | ColumnnncCrSpvpcBwdTmPolicingOption | read-create | current | Policing Option for an SPVPC. tag is supported only on rt-VBR/nrt-VBR connections that use the P_0+1/S_0 traffic descriptor |
| 1.3.6.1.4.1.123.3.82.1.1.1.27 | ColumnnncCrSpvpcBwdTmBucketOneRate | read-create | current | This object is for peak information rate (PIR), the cell rate which the source may never exceed. It is used to determine which cells are 'excess'. Measured in … |
| 1.3.6.1.4.1.123.3.82.1.1.1.28 | ColumnnncCrSpvpcBwdTmBucketOneCdvt | read-create | current | This object is used to set cell delay variation tolerance (CDVT) for one endpoint, measured in microseconds. Range: 1 - 190,000 microseconds |
| 1.3.6.1.4.1.123.3.82.1.1.1.29 | ColumnnncCrSpvpcBwdTmBucketTwoRate | read-create | current | SIR_0p, SIR_0+1p or MIR_0+1p. This parameter holds the sustained information rate for VBR traffic, and the minimum information rate for ABR/UBR traffic. Range:… |
| 1.3.6.1.4.1.123.3.82.1.1.1.30 | ColumnnncCrSpvpcBwdTmBucketTwoMbs | read-create | current | This object is for the maximum burst size, in cells, for SIR_0p or SIR_0+1p (nrtVbr and rtVbr only). Range: 1 - 10000 cells |
| 1.3.6.1.4.1.123.3.82.1.1.1.31 | ColumnnncCrSpvpcBwdTmCdv | read-create | current | This value is to set the cell delay variation (CDV) between two endpoints to support the rt-VBR service category. Range: 250-10000 microseconds |
| 1.3.6.1.4.1.123.3.82.1.1.1.32 | ColumnnncCrSpvpcBwdTmClr | read-create | current | The object is to set the cell loss ratio (CLR) between two SPVC endpoints when using the nrt-VBR service category. Value set as 1.0e-# |
| 1.3.6.1.4.1.123.3.82.1.1.1.33 | ColumnnncCrSpvpcCreator | read-only | current | The object retrieves the creator of a SPVC connection. |
| 1.3.6.1.4.1.123.3.82.1.1.1.34 | ColumnnncCrSpvpcRowStatus | read-create | current | This object is used to control the status of a PDU and to query the status of an SPVC. When the RowStatus value is 'createAndWait', information for a row is ca… |
| 1.3.6.1.4.1.123.3.82.1.2 | TablenncCrSpvpcDstCfgTable | not-accessible | current | the nncCrSpvpcDstCfg table contains common objects used to configure, delete, modify and query the destination end point of an SPVC across different Alcatel CI… |
| 1.3.6.1.4.1.123.3.82.1.2.1 | RownncCrSpvpcDstCfgTableEntry | not-accessible | current | An entry of nncCrSpvpcDstCfgTable. |
| 1.3.6.1.4.1.123.3.82.1.2.1.1 | ColumnnncCrSpvpcDstCfgCdvt | read-create | current | This object is used to set cell delay variation tolerance (CDVT) for one endpoint, measured in microseconds. Range: 1 - 190,000 microseconds |
| 1.3.6.1.4.1.123.3.82.1.2.1.2 | ColumnnncCrSpvpcDstCfgPolicing | read-create | current | CR Policing |
| 1.3.6.1.4.1.123.3.82.1.2.1.3 | ColumnnncCrSpvpcDstCfgBillingFlag | read-create | current | Billing Configuration for the destination endpoint. |
| 1.3.6.1.4.1.123.3.82.1.2.1.4 | ColumnnncCrSpvpcDstCfgLocRerouteConfig | read-create | current | This object is used to configure the 'reroute on loss of continuity' feature using OAM-CC cells. It can be configured for either the UNI side or the NNI side, … |
| 1.3.6.1.4.1.123.3.82.1.2.1.5 | ColumnnncCrSpvpcDstCfgRowStatus | read-create | current | This object is used to control the status of a PDU and to query the status of an SPVC. When the RowStatus value is 'createAndWait', information for a row is ca… |
| 1.3.6.1.4.1.123.3.82.1.3 | TablenncCrSpvccTable | not-accessible | current | nncCrSpvccTable contains all the objects sent to a source endpoint that are used to create, modify, delete and query Cell Relay SPVC connections. |
| 1.3.6.1.4.1.123.3.82.1.3.1 | RownncCrSpvccTableEntry | not-accessible | current | An entry of nncCrSpvccTable. It contains the objects required to manage CR SPVCs. |
| 1.3.6.1.4.1.123.3.82.1.3.1.1 | ColumnnncCrSpvccServiceCategory | read-create | current | This object is used to set the traffic service category. This object is dependent on the value specified in nncCrSpvccTrafficDescriptor |
| 1.3.6.1.4.1.123.3.82.1.3.1.2 | ColumnnncCrSpvccTargEpAddr | read-create | current | This object is used to specify the AESA address for the target endpoint. The mapping scheme is as follows: Byte\Bit 8 7 6 5 4 3 2 1 1-13 byte | 13-byte Interna… |
| 1.3.6.1.4.1.123.3.82.1.3.1.3 | ColumnnncCrSpvccTargVpi | read-create | current | This object contains the virtual path identifier (VPI) value for the target endpoint. Range: 0 - 4095 |
| 1.3.6.1.4.1.123.3.82.1.3.1.4 | ColumnnncCrSpvccTargVci | read-create | current | This object contains the virtual channel identifier (VCI) value for the target endpoint. Range: 1 - 65535 |
| 1.3.6.1.4.1.123.3.82.1.3.1.5 | ColumnnncCrSpvccTargDlci | not-accessible | current | This object contains the data link connection identifier for a frame relay endpoint. This number is used to identify the target endpoint, and has only local si… |
| 1.3.6.1.4.1.123.3.82.1.3.1.6 | ColumnnncCrSpvccTargCeNumber | not-accessible | current | This object contains circuit number, channel group number or both for the Circuit Emulation endpoint. Used in CR to CE connections when nncCrSpvccTargEpType is… |
| 1.3.6.1.4.1.123.3.82.1.3.1.7 | ColumnnncCrSpvccTargEpType | read-create | current | This object specifies a target endpoint as one of the following types: cellRelay (1) frameRelay (2) circuitEmulation (3) |
| 1.3.6.1.4.1.123.3.82.1.3.1.8 | ColumnnncCrSpvccAdminStatus | read-create | current | This object accepts two values, enabled (1), and disabled (2). When the value is disabled, the SPVC is not connected. When enabled, the SPVC is connected when … |
| 1.3.6.1.4.1.123.3.82.1.3.1.9 | ColumnnncCrSpvccPriority | read-create | current | This object is used to set the priority for a SPVC connection request. It ranges between 1-16, with the following values: Best Priority = 1 Default Priority = … |
| 1.3.6.1.4.1.123.3.82.1.3.1.10 | ColumnnncCrSpvccMaxAdminWeight | read-create | current | This object is used to set a cost threshold for an SPVC connection. If the total cost of all VPCs exceeds this weight value for a given path, this SPVC will ch… |
| 1.3.6.1.4.1.123.3.82.1.3.1.11 | ColumnnncCrSpvccOperation | read-create | current | This object is used to request a reroute operation. Querying this object will not provide any useful information. |
| 1.3.6.1.4.1.123.3.82.1.3.1.12 | ColumnnncCrSpvccCallStatus | read-only | current | This read-only object is used to query the state of a particular SPVC. SPVCs that are connected and operational will return a value of 'connected', while those… |
| 1.3.6.1.4.1.123.3.82.1.3.1.13 | ColumnnncCrSpvccLocRerouteConfig | read-create | current | This object is used to configure the 'reroute on loss of continuity' feature using OAM-CC cells. It can be configured for either the UNI side or the NNI side, … |
| 1.3.6.1.4.1.123.3.82.1.3.1.14 | ColumnnncCrSpvccFwdAbrDynTrfcIcr | read-create | current | ABR dynamic traffic descriptor's Initial Cell Rate for the forward direction. Range: 0 - 2488320 Kb/s |
| 1.3.6.1.4.1.123.3.82.1.3.1.15 | ColumnnncCrSpvccFwdAbrDynTrfcRif | read-create | current | ABR traffic Rate Increase Factor for the forward direction. Value is expressed as the -power of 2. Range: 0 - 9 |
| 1.3.6.1.4.1.123.3.82.1.3.1.16 | ColumnnncCrSpvccFwdAbrDynTrfcRdf | read-create | current | ABR traffic Rate Decrease Factor descriptor for the forward direction. Value is expressed as the -power of 2 Range: 0 - 9 |
| 1.3.6.1.4.1.123.3.82.1.3.1.17 | ColumnnncCrSpvccBwdAbrDynTrfcIcr | read-create | current | ABR dynamic traffic descriptor's Initial Cell Rate for the destination endpoint. Range: 0 - 2488320 Kb/s |
| 1.3.6.1.4.1.123.3.82.1.3.1.18 | ColumnnncCrSpvccBwdAbrDynTrfcRif | read-create | current | ABR traffic Rate Increase Factor for the backward direction. Value is expressed as the -power of 2. Range: 0 - 9 |
| 1.3.6.1.4.1.123.3.82.1.3.1.19 | ColumnnncCrSpvccBwdAbrDynTrfcRdf | read-create | current | ABR traffic Rate Decrease Factor descriptor for the backward direction. Value is expressed as the -power of 2 Range: 0 - 9 |
| 1.3.6.1.4.1.123.3.82.1.3.1.20 | ColumnnncCrSpvccSrcBillingFlag | read-create | current | Billing Configuration for the source endpoint |
| 1.3.6.1.4.1.123.3.82.1.3.1.21 | ColumnnncCrSpvccFwdTmTrafficDescriptor | read-create | current | This object contains the traffic descriptor for the SPVC. Tag All (1) (UBR using 2k/12k fabric only) P_0+1 (2) (CBR only) P_0+1/S_0+1 (3) (NRT/RT-VBR only) P_0… |
| 1.3.6.1.4.1.123.3.82.1.3.1.22 | ColumnnncCrSpvccFwdTmPolicingOption | read-create | current | Policing Option for an SPVCC. tag is supported only on rt-VBR/nrt-VBR connections that use the P_0+1/S_0 traffic descriptor |
| 1.3.6.1.4.1.123.3.82.1.3.1.23 | ColumnnncCrSpvccFwdTmBucketOneRate | read-create | current | This object is for peak cell rate (PCR), the cell rate which the source may never exceed. It is used to determine which cells are 'excess'. Measured in Kb/s. R… |
| 1.3.6.1.4.1.123.3.82.1.3.1.24 | ColumnnncCrSpvccFwdTmBucketOneCdvt | read-create | current | This object is used to set cell delay variation tolerance (CDVT) for one endpoint, measured in microseconds. Range: 1 - 190,000 microseconds |
| 1.3.6.1.4.1.123.3.82.1.3.1.25 | ColumnnncCrSpvccFwdTmBucketTwoRate | read-create | current | SIR_0p, SIR_0+1p or MIR_0+1p. This parameter holds the sustained information rate for VBR traffic, and the minimum information rate for ABR/UBR traffic. Range:… |
| 1.3.6.1.4.1.123.3.82.1.3.1.26 | ColumnnncCrSpvccFwdTmBucketTwoMbs | read-create | current | This object is for the maximum burst size, in cells, for SIR_0p or SIR_0+1p (nrtVbr and rtVbr only). Range: 1 - 10000 cells |
| 1.3.6.1.4.1.123.3.82.1.3.1.27 | ColumnnncCrSpvccFwdTmCdv | read-create | current | This value is to set the cell delay variation (CDV) between two endpoints to support the rt-VBR service category. Range: 250-10000 microseconds |
| 1.3.6.1.4.1.123.3.82.1.3.1.28 | ColumnnncCrSpvccFwdTmClr | read-create | current | The object is to set the cell loss ratio (CLR) between two SPVC endpoints when using the nrt-VBR service category. Value set as 1.0e-# |
| 1.3.6.1.4.1.123.3.82.1.3.1.29 | ColumnnncCrSpvccFwdTmFrameDiscard | read-create | current | The Frame (AAL protocol data unit) Discard option. When enabled, cells are discarded at the frame level by examining the SDU-type in the payload type field of … |
| 1.3.6.1.4.1.123.3.82.1.3.1.30 | ColumnnncCrSpvccBwdTmTrafficDescriptor | read-create | current | This object contains the traffic descriptor for the SPVC. Tag All (1) (UBR using 2k/12k fabric only) P_0+1 (2) (CBR only) P_0+1/S_0+1 (3) (NRT/RT-VBR only) P_0… |
| 1.3.6.1.4.1.123.3.82.1.3.1.31 | ColumnnncCrSpvccBwdTmPolicingOption | read-create | current | Policing Option for an SPVCC. tag is supported only on rt-VBR/nrt-VBR connections that use the P_0+1/S_0 traffic descriptor |
| 1.3.6.1.4.1.123.3.82.1.3.1.32 | ColumnnncCrSpvccBwdTmBucketOneRate | read-create | current | This object is for peak cell rate (PCR), the cell rate which the source may never exceed. It is used to determine which cells are 'excess'. Measured in Kb/s. R… |
| 1.3.6.1.4.1.123.3.82.1.3.1.33 | ColumnnncCrSpvccBwdTmBucketOneCdvt | read-create | current | This object is used to set cell delay variation tolerance (CDVT) for one endpoint, measured in microseconds. Range: 1 - 190,000 microseconds |
| 1.3.6.1.4.1.123.3.82.1.3.1.34 | ColumnnncCrSpvccBwdTmBucketTwoRate | read-create | current | SIR_0p, SIR_0+1p or MIR_0+1p. This parameter holds the sustained information rate for VBR traffic, and the minimum information rate for ABR/UBR traffic. Range:… |
| 1.3.6.1.4.1.123.3.82.1.3.1.35 | ColumnnncCrSpvccBwdTmBucketTwoMbs | read-create | current | This object is for the maximum burst size, in cells, for SIR_0p or SIR_0+1p (nrt-VBR and rt-VBR only). Range: 1 - 10000 cells |
| 1.3.6.1.4.1.123.3.82.1.3.1.36 | ColumnnncCrSpvccBwdTmCdv | read-create | current | This value is to set the cell delay variation (CDV) between two endpoints to support the rt-VBR service category. Range: 250-10000 microseconds |
| 1.3.6.1.4.1.123.3.82.1.3.1.37 | ColumnnncCrSpvccBwdTmClr | read-create | current | The object is to set the cell loss ratio (CLR) between two SPVC endpoints when using the nrt-VBR service category. Value set as 1.0e-# |
| 1.3.6.1.4.1.123.3.82.1.3.1.38 | ColumnnncCrSpvccBwdTmFrameDiscard | read-create | current | The Frame (AAL protocol data unit) Discard option. When enabled, cells are discarded at the frame level by examining the SDU-type in the payload type field of … |
| 1.3.6.1.4.1.123.3.82.1.3.1.39 | ColumnnncCrSpvccFrBwdTmAr | read-create | current | This object is used to specify the Access Rate, in Kb/s. |
| 1.3.6.1.4.1.123.3.82.1.3.1.40 | ColumnnncCrSpvccFrBwdTmCir | read-create | current | The committed Information Rate, in Kb/s. |
| 1.3.6.1.4.1.123.3.82.1.3.1.41 | ColumnnncCrSpvccFrBwdTmBc | read-create | current | The Committed Burst Size, in Kb. |
| 1.3.6.1.4.1.123.3.82.1.3.1.42 | ColumnnncCrSpvccFrBwdTmBe | read-create | current | The Excess Burst Size, in Kb. |
| 1.3.6.1.4.1.123.3.82.1.3.1.43 | ColumnnncCrSpvccFrBwdTmIwf | read-create | current | Interworking Function. Values: none (None (FR Switching) = 0) networkInterworking (Network Interworking = 2) serviceInterworking (Service Interworking = 3) FFw… |
| 1.3.6.1.4.1.123.3.82.1.3.1.44 | ColumnnncCrSpvccFrBwdTmPo | read-create | current | Policing |
| 1.3.6.1.4.1.123.3.82.1.3.1.45 | ColumnnncCrSpvccFrBwdTmPacing | read-create | current | Pacing |
| 1.3.6.1.4.1.123.3.82.1.3.1.46 | ColumnnncCrSpvccFrBwdTmPtclMapping | read-create | current | Protocol Mapping for Service Interworking SPVCs. If Translated Service Interworking is selected, the a profile must be set using the attribute nncFrSpvcTmSIWPr… |
| 1.3.6.1.4.1.123.3.82.1.3.1.47 | ColumnnncCrSpvccFrBwdTmClpMapping | read-create | current | Cell Loss Priority Mapping. Values: cLPEqualsDE (CLP = DE, 0) cLPEquals0 (CLP = 0, 1 ) cLPEquals1 (CLP = 1, 2 ) |
| 1.3.6.1.4.1.123.3.82.1.3.1.48 | ColumnnncCrSpvccFrBwdTmDeMapping | read-create | current | Discard Eligibility Mapping Values: dEEqualsCLP (DE = CLP, 0) dESSCSor0 (Network Interworking: DE=FR_SSCS Service Interworking: DE=0, 1) dEEquals1 (Service Int… |
| 1.3.6.1.4.1.123.3.82.1.3.1.49 | ColumnnncCrSpvccFrBwdTmEfciMapping | read-create | current | Explicit Forward Congestion Indication Mapping (Applies only to Service Interworking (IWF3), FR to ATM) Values: eFCIEqualsFECN (EFCI = FECN, 0) eFCIEquals0 (EF… |
| 1.3.6.1.4.1.123.3.82.1.3.1.50 | ColumnnncCrSpvccFrBwdTmPvcMgntProfile | read-create | current | Enables or disables the PVC Management Profile. When enabled, LMI is enabled on the network-side of the connection. Used only with FR-CR network interworking s… |
| 1.3.6.1.4.1.123.3.82.1.3.1.51 | ColumnnncCrSpvccFrBwdTmSIWProfile | read-create | current | The FR-CR profile index for service interworking connections. This attribute is used to define the translation profile to use when a FR to CR SPVC is configure… |
| 1.3.6.1.4.1.123.3.82.1.3.1.52 | ColumnnncCrSpvccCreator | read-only | current | The object retrieves the creator of a SPVC connection. |
| 1.3.6.1.4.1.123.3.82.1.3.1.53 | ColumnnncCrSpvccRowStatus | read-create | current | This object is used to control the status of a PDU and to query the status of an SPVC. When the RowStatus value is 'createAndWait', information for a row is ca… |
| 1.3.6.1.4.1.123.3.82.1.4 | TablenncCrSpvccDstCfgTable | not-accessible | current | the nncCrSpvccDstCfg table contains common objects used to configure, delete, modify and query the destination end point of an SPVC across different Alcatel CI… |
| 1.3.6.1.4.1.123.3.82.1.4.1 | RownncCrSpvccDstCfgTableEntry | not-accessible | current | An entry of nncCrSpvccDstCfgTable. |
| 1.3.6.1.4.1.123.3.82.1.4.1.1 | ColumnnncCrSpvccDstCfgCdvt | read-create | current | This object is used to set cell delay variation tolerance (CDVT) for one endpoint, measured in microseconds. Range: 1 - 190,000 microseconds |
| 1.3.6.1.4.1.123.3.82.1.4.1.2 | ColumnnncCrSpvccDstCfgPolicing | read-create | current | CR Policing |
| 1.3.6.1.4.1.123.3.82.1.4.1.3 | ColumnnncCrSpvccDstCfgBillingFlag | read-create | current | Billing Configuration for the destination endpoint |
| 1.3.6.1.4.1.123.3.82.1.4.1.4 | ColumnnncCrSpvccDstCfgFrVsvdCongestionControl | read-create | current | Congestion Control for VS/VD endpoints, also known as Closed Loop Congestion Control (CLCC). |
| 1.3.6.1.4.1.123.3.82.1.4.1.5 | ColumnnncCrSpvccDstCfgLocRerouteConfig | read-create | current | This object is used to configure the 'reroute on loss of continuity' feature using OAM-CC cells. It can be configured for either the UNI side or the NNI side, … |
| 1.3.6.1.4.1.123.3.82.1.4.1.6 | ColumnnncCrSpvccDstCfgRowStatus | read-create | current | This object is used to control the status of a PDU and to query the status of an SPVC. When the RowStatus value is 'createAndWait', information for a row is ca… |
| 1.3.6.1.4.1.123.3.82.1.5 | TablenncFrSpvcTable | not-accessible | current | nncFrSpvcTable contains all the objects sent to a source endpoint that are used to create, modify, delete and query FR SPVCCs. |
| 1.3.6.1.4.1.123.3.82.1.5.1 | RownncFrSpvcTableEntry | not-accessible | current | An entry of nncFrSpvcTable. |
| 1.3.6.1.4.1.123.3.82.1.5.1.1 | ColumnnncFrSpvcSrcDlci | not-accessible | current | This object contains the data link connection identifier for a frame relay endpoint. This number is used to identify the source endpoint, and has only local si… |
| 1.3.6.1.4.1.123.3.82.1.5.1.2 | ColumnnncFrSpvcTargEpAddr | read-create | current | This object contains the target endpoint's 20-byte ATM End System Address (AESA) proposed by ATM Forum. An endpoint address is created by appending the switch-… |
| 1.3.6.1.4.1.123.3.82.1.5.1.3 | ColumnnncFrSpvcTargDlci | read-create | current | This object contains the data link connection identifier for a frame relay endpoint. This number is used to identify the target endpoint, and has only local si… |
| 1.3.6.1.4.1.123.3.82.1.5.1.4 | ColumnnncFrSpvcTargVpi | read-create | current | This object contains the virtual path identifier (VPI) value for the Cell Relay based target endpoint. Range: 0 - 4095 |
| 1.3.6.1.4.1.123.3.82.1.5.1.5 | ColumnnncFrSpvcTargVci | read-create | current | This object contains the virtual channel identifier (VCI) value for the cell-relay based target endpoint. Range: 1 - 65535 |
| 1.3.6.1.4.1.123.3.82.1.5.1.6 | ColumnnncFrSpvcTargEpType | read-create | current | This object specifies a target endpoint as one of the following types: cellRelay (1) frameRelay (2) |
| 1.3.6.1.4.1.123.3.82.1.5.1.7 | ColumnnncFrSpvcAdminStatus | read-create | current | This object accepts two values, enabled (1), and disabled (2). When the value is disabled, the SPVC is not connected. When enabled, the SPVC is connected when … |
| 1.3.6.1.4.1.123.3.82.1.5.1.8 | ColumnnncFrSpvcPriority | read-create | current | This object is used to set the priority for a SPVC connection request. It ranges between 1-16, with the following values: Best Priority = 1 Default Priority = … |
| 1.3.6.1.4.1.123.3.82.1.5.1.9 | ColumnnncFrSpvcMaxAdminWeight | read-create | current | This object is used to set a cost threshold for an SPVC connection. If the total cost of all VPCs exceeds this weight value for a given path, this SPVC will ch… |
| 1.3.6.1.4.1.123.3.82.1.5.1.10 | ColumnnncFrSpvcOperation | read-create | current | This object is used to request a reroute operation. Querying this object will not provide any useful information. |
| 1.3.6.1.4.1.123.3.82.1.5.1.11 | ColumnnncFrSpvcCallStatus | read-only | current | This read-only object is used to query the state of a particular SPVC. SPVCs that are connected and operational will return a value of 'connected', while those… |
| 1.3.6.1.4.1.123.3.82.1.5.1.12 | ColumnnncFrSpvcLocRerouteConfig | read-create | current | This object is used to configure the 'reroute on loss of continuity' feature using OAM-CC cells. It can be configured for either the UNI side or the NNI side, … |
| 1.3.6.1.4.1.123.3.82.1.5.1.13 | ColumnnncFrSpvcSrcBillingFlag | read-create | current | Billing Configuration for the source endpoint. |
| 1.3.6.1.4.1.123.3.82.1.5.1.14 | ColumnnncFrSpvcFrPriority | read-create | current | Frame Relay Priority. |
| 1.3.6.1.4.1.123.3.82.1.5.1.15 | ColumnnncFrSpvcFrVsvdCongestionControl | read-create | current | Congestion Control for VS/VD endpoints, also known as Closed Loop Congestion Control (CLCC). |
| 1.3.6.1.4.1.123.3.82.1.5.1.16 | ColumnnncFrSpvcFwdFrMir | read-create | current | The FR Src->Dst Minimum Information Rate, used to set the minimum rate on a CLCC FR-FR SPVC connection. If nncFrSpvcFrVsvdCongestionControl is not enabled, thi… |
| 1.3.6.1.4.1.123.3.82.1.5.1.17 | ColumnnncFrSpvcFwdTmAr | read-create | current | This object is used to specify the Access Rate, in Kb/s |
| 1.3.6.1.4.1.123.3.82.1.5.1.18 | ColumnnncFrSpvcFwdTmCir | read-create | current | The committed Information Rate, in Kb/s |
| 1.3.6.1.4.1.123.3.82.1.5.1.19 | ColumnnncFrSpvcFwdTmBc | read-create | current | The Committed Burst Size, in Kb. |
| 1.3.6.1.4.1.123.3.82.1.5.1.20 | ColumnnncFrSpvcFwdTmBe | read-create | current | Excess Burst Size, Kb. |
| 1.3.6.1.4.1.123.3.82.1.5.1.21 | ColumnnncFrSpvcTmIwf | read-create | current | Interworking Function. Values: none (None (FR Switching) = 0) networkInterworking (Network Interworking = 2) serviceInterworking (Service Interworking = 3) FFw… |
| 1.3.6.1.4.1.123.3.82.1.5.1.22 | ColumnnncFrSpvcFwdTmPo | read-create | current | Policing. |
| 1.3.6.1.4.1.123.3.82.1.5.1.23 | ColumnnncFrSpvcFwdTmPacing | read-create | current | Pacing. |
| 1.3.6.1.4.1.123.3.82.1.5.1.24 | ColumnnncFrSpvcTmPtclMapping | read-create | current | Protocol Mapping for Service Interworking SPVCs. If Translated Service Interworking is selected, the a profile must be set using the attribute nncFrSpvcTmSIWPr… |
| 1.3.6.1.4.1.123.3.82.1.5.1.25 | ColumnnncFrSpvcTmClpMapping | read-create | current | Cell Loss Priority Mapping, for use in FR-CR interworking SPVCs. Values: cLPEqualsDE (CLP = DE, 0) cLPEquals0 (CLP = 0, 1 ) cLPEquals1 (CLP = 1, 2 ) |
| 1.3.6.1.4.1.123.3.82.1.5.1.26 | ColumnnncFrSpvcTmDeMapping | read-create | current | Discard Eligibility Mapping, for use in FR-CR interworking SPVCs. Values: dEEqualsCLP (DE = CLP, 0) dESSCSor0 (Network Interworking: DE=FR_SSCS Service Interwo… |
| 1.3.6.1.4.1.123.3.82.1.5.1.27 | ColumnnncFrSpvcTmEfciMapping | read-create | current | Explicit Forward Congestion Indication Mapping (Applies only to Service Interworking (IWF3), FR to ATM) Values: eFCIEqualsFECN (EFCI = FECN, 0) eFCIEquals0 (EF… |
| 1.3.6.1.4.1.123.3.82.1.5.1.28 | ColumnnncFrSpvcTmPvcMgntProfile | read-create | current | Enables or disables the PVC Management Profile. When enabled, LMI is enabled on the network-side of the connection. Used only with FR-CR network interworking s… |
| 1.3.6.1.4.1.123.3.82.1.5.1.29 | ColumnnncFrSpvcTmSIWProfile | read-create | current | The FR-CR profile index for service interworking connections. This attribute is used to define the translation profile to use when a FR to CR SPVC is configure… |
| 1.3.6.1.4.1.123.3.82.1.5.1.30 | ColumnnncFrSpvcTmRemapDlci | read-create | current | The source end-point Data Link Connection Identifier for many-to-one Network Interworking (IWF2) connections. |
| 1.3.6.1.4.1.123.3.82.1.5.1.31 | ColumnnncFrSpvcBwdFrMir | read-create | current | The FR Dst->Src Minimum Information Rate, used on CLCC-enabled connections. Range: 0 - 44210 Kb/s |
| 1.3.6.1.4.1.123.3.82.1.5.1.32 | ColumnnncFrSpvcBwdTmAr | read-create | current | This object is used to specify the Access Rate, in Kb/s |
| 1.3.6.1.4.1.123.3.82.1.5.1.33 | ColumnnncFrSpvcBwdTmCir | read-create | current | The committed Information Rate, in Kb/s |
| 1.3.6.1.4.1.123.3.82.1.5.1.34 | ColumnnncFrSpvcBwdTmBc | read-create | current | The Committed Burst Size, in Kb. |
| 1.3.6.1.4.1.123.3.82.1.5.1.35 | ColumnnncFrSpvcBwdTmBe | read-create | current | The Excess Burst Size, Kb. |
| 1.3.6.1.4.1.123.3.82.1.5.1.36 | ColumnnncFrSpvcBwdTmPo | read-create | current | Policing. |
| 1.3.6.1.4.1.123.3.82.1.5.1.37 | ColumnnncFrSpvcBwdTmPacing | read-create | current | Pacing. |
| 1.3.6.1.4.1.123.3.82.1.5.1.38 | ColumnnncFrSpvcCrTmServiceCategory | read-create | current | This object is used to set the traffic service category for SPVC Connections. This object is dependent on the value specified in nncFrSpvcCrBwdTmTrafficDescrip… |
| 1.3.6.1.4.1.123.3.82.1.5.1.39 | ColumnnncFrSpvcCrBwdTmTrafficDescriptor | read-create | current | This object contains the CR traffic descriptor for a FR-CR SPVC. Tag All (1) (UBR using 2k/12k fabric only) P_0+1/S_0+1 (3) (NRT/RT-VBR only) P_0+1/S_0 (4) (NR… |
| 1.3.6.1.4.1.123.3.82.1.5.1.40 | ColumnnncFrSpvcCrBwdTmPolicingOption | read-create | current | Policing Option for a FR SPVC. tag is supported only on rt-VBR/nrt-VBR connections that use the P_0+1/S_0 traffic descriptor |
| 1.3.6.1.4.1.123.3.82.1.5.1.41 | ColumnnncFrSpvcCrBwdTmBucketOneRate | read-create | current | Used in FR - CR interworking. This object is for peak cell rate (PCR), the cell rate which the cell endpoint may never exceed. It is used to determine which ce… |
| 1.3.6.1.4.1.123.3.82.1.5.1.42 | ColumnnncFrSpvcCrBwdTmBucketOneCdvt | read-create | current | This object is used to set cell delay variation tolerance (CDVT) for the CR endpoint, measured in microseconds. Range: 1 - 190,000 microseconds |
| 1.3.6.1.4.1.123.3.82.1.5.1.43 | ColumnnncFrSpvcCrBwdTmBucketTwoRate | read-create | current | Used in FR - CR interworking. The attribute contains the SIR_0, SIR_0+1 or MIR_0+1. This parameter holds the sustained information rate (SIR_0 or SIR_0+1) for … |
| 1.3.6.1.4.1.123.3.82.1.5.1.44 | ColumnnncFrSpvcCrBwdTmBucketTwoMbs | read-create | current | This object is for the maximum burst size, in cells, for SIR_0p or SIR_0+1p (nrtVbr and rtVbr only). Range: 1 - 10000 cells |
| 1.3.6.1.4.1.123.3.82.1.5.1.45 | ColumnnncFrSpvcCrBwdTmCdv | read-create | current | This value is to set the cell delay variation (CDV) at the CR endpoint. Applicable only when the rt-VBR service category is used. Range: 250-10000 microseconds |
| 1.3.6.1.4.1.123.3.82.1.5.1.46 | ColumnnncFrSpvcCrBwdTmClr | read-create | current | The object is to set the cell loss ratio (CLR) at the CR endpoint of a FR-CR SPVC. Valid only when using the nrt-VBR service category. Value set as 1.0e-# |
| 1.3.6.1.4.1.123.3.82.1.5.1.47 | ColumnnncFrSpvcCrBwdTmFrameDiscard | read-create | current | The Frame (AAL protocol data unit) Discard option. When enabled, cells are discarded at the frame level by examining the SDU-type in the payload type field of … |
| 1.3.6.1.4.1.123.3.82.1.5.1.48 | ColumnnncFrSpvcCreator | read-only | current | The object retrieves the creator of a given SPVC connection. |
| 1.3.6.1.4.1.123.3.82.1.5.1.49 | ColumnnncFrSpvcRowStatus | read-create | current | This object is used to control the status of a PDU and to query the status of an SPVC. When the RowStatus value is 'createAndWait', information for a row is ca… |
| 1.3.6.1.4.1.123.3.82.1.6 | TablenncFrSpvcDstCfgTable | not-accessible | current | the nncFrSpvcDstCfg table contains common objects used to configure, delete, modify and query the destination end point of an SPVC across different Alcatel CID… |
| 1.3.6.1.4.1.123.3.82.1.6.1 | RownncFrSpvcDstCfgTableEntry | not-accessible | current | An entry of nncFrSpvcDstCfgTable. |
| 1.3.6.1.4.1.123.3.82.1.6.1.1 | ColumnnncFrSpvcDstCfgTmAr | read-create | current | This object is used to specify the Access Rate, in Kb/s |
| 1.3.6.1.4.1.123.3.82.1.6.1.2 | ColumnnncFrSpvcDstCfgTmCir | read-create | current | The committed Information Rate, Kb/s |
| 1.3.6.1.4.1.123.3.82.1.6.1.3 | ColumnnncFrSpvcDstCfgTmBc | read-create | current | The Committed Burst Size, in Kb. |
| 1.3.6.1.4.1.123.3.82.1.6.1.4 | ColumnnncFrSpvcDstCfgTmBe | read-create | current | Excess Burst Size, in Kb. |
| 1.3.6.1.4.1.123.3.82.1.6.1.5 | ColumnnncFrSpvcDstCfgTmIwf | read-create | current | Interworking Function. Values: none (None (FR Switching) = 0) networkInterworking (Network Interworking = 2) serviceInterworking (Service Interworking = 3) FFw… |
| 1.3.6.1.4.1.123.3.82.1.6.1.6 | ColumnnncFrSpvcDstCfgTmPo | read-create | current | Policing. |
| 1.3.6.1.4.1.123.3.82.1.6.1.7 | ColumnnncFrSpvcDstCfgTmPacing | read-create | current | Pacing. |
| 1.3.6.1.4.1.123.3.82.1.6.1.8 | ColumnnncFrSpvcDstCfgTmPtclMapping | read-create | current | Protocol Mapping for Service Interworking SPVCs. If Translated Service Interworking is selected, the a profile must be set using the attribute nncFrSpvcTmPvcMg… |
| 1.3.6.1.4.1.123.3.82.1.6.1.9 | ColumnnncFrSpvcDstCfgTmClpMapping | read-create | current | Cell Loss Priority Mapping. Values: cLPEqualsDE (CLP = DE) cLPEquals0 (CLP = 0 ) cLPEquals1 (CLP = 1 ) |
| 1.3.6.1.4.1.123.3.82.1.6.1.10 | ColumnnncFrSpvcDstCfgTmDeMapping | read-create | current | Discard Eligibility Mapping Values: dEEqualsCLP (DE = CLP, 0) dESSCSor0 (Network Interworking: DE=FR_SSCS Service Interworking: DE=0, 1) dEEquals1 (Service Int… |
| 1.3.6.1.4.1.123.3.82.1.6.1.11 | ColumnnncFrSpvcDstCfgTmEfciMapping | read-create | current | Explicit Forward Congestion Indication Mapping (Applies only to Service Interworking (IWF3), FR to ATM) Values: eFCIEqualsFECN (0) eFCIEquals0 (1) |
| 1.3.6.1.4.1.123.3.82.1.6.1.12 | ColumnnncFrSpvcDstCfgTmPvcMgntProfile | read-create | current | Enables or disables the PVC Management Profile. When enabled, LMI is enabled on the network-side of the connection. Used only with FR-CR network interworking s… |
| 1.3.6.1.4.1.123.3.82.1.6.1.13 | ColumnnncFrSpvcDstCfgTmSIWProfile | read-create | current | The FR-CR profile index for service interworking connections. This attribute is used to define the translation profile to use when a FR to CR SPVC is configure… |
| 1.3.6.1.4.1.123.3.82.1.6.1.14 | ColumnnncFrSpvcDstCfgTmRemapDlci | read-create | current | The source end-point Data Link Connection Identifier for many-to-one Network Interworking (IWF2) connections. |
| 1.3.6.1.4.1.123.3.82.1.6.1.15 | ColumnnncFrSpvcDstCfgBillingFlag | read-create | current | Billing Configuration for the destination endpoint. |
| 1.3.6.1.4.1.123.3.82.1.6.1.16 | ColumnnncFrSpvcDstCfgFrPriority | read-create | current | Frame Relay Priority. |
| 1.3.6.1.4.1.123.3.82.1.6.1.17 | ColumnnncFrSpvcDstCfgLocRerouteConfig | read-create | current | This object is used to configure the 'reroute on loss of continuity' feature using OAM-CC cells. It can be configured for either the UNI side or the NNI side, … |
| 1.3.6.1.4.1.123.3.82.1.6.1.18 | ColumnnncFrSpvcDstCfgRowStatus | read-create | current | This object is used to control the status of a PDU and to query the status of an SPVC. When the RowStatus value is 'createAndWait', information for a row is ca… |
| 1.3.6.1.4.1.123.3.82.1.7 | TablenncCeSpvcTable | not-accessible | current | nncCeSpvcTable contains all the objects sent to a source endpoint that are used to create, modify, delete and query CE SPVCCs. The table is indexed using ifInd… |
| 1.3.6.1.4.1.123.3.82.1.7.1 | RownncCeSpvcTableEntry | not-accessible | current | An entry of nncCeSpvcTable. |
| 1.3.6.1.4.1.123.3.82.1.7.1.1 | ColumnnncCeSpvcTargEpAddr | read-create | current | This object is used to specify the AESA address of the target endpoint. The mapping scheme is as follows: Byte\Bit 8 7 6 5 4 3 2 1 1-13 byte | 13-byte Internal… |
| 1.3.6.1.4.1.123.3.82.1.7.1.2 | ColumnnncCeSpvcTargVpi | read-create | current | This object contains the virtual path identifier (VPI) value for the target endpoint. Used in interworking CE to CR connections when nncCeSpvcTargEpType config… |
| 1.3.6.1.4.1.123.3.82.1.7.1.3 | ColumnnncCeSpvcTargVci | read-create | current | This object contains the virtual channel identifier (VCI) value for the target endpoint. Used in interworking CE to CR connections when nncCeSpvcTargEpType con… |
| 1.3.6.1.4.1.123.3.82.1.7.1.4 | ColumnnncCeSpvcTargCeNumber | read-create | current | This object contains circuit number, channel group number or both for the Circuit Emulation endpoint. Used in CE to CE connections when nncCrSpvccTargEpType is… |
| 1.3.6.1.4.1.123.3.82.1.7.1.5 | ColumnnncCeSpvcTargEpType | read-create | current | This object specifies a target endpoint as one of the following types: cellRelay (1) circuitEmulation (3) |
| 1.3.6.1.4.1.123.3.82.1.7.1.6 | ColumnnncCeSpvcAdminStatus | read-create | current | This object accepts two values, enabled (1), and disabled (2). When the value is disabled, the SPVC is not connected. When enabled, the SPVC is connected when … |
| 1.3.6.1.4.1.123.3.82.1.7.1.7 | ColumnnncCeSpvcPriority | read-create | current | This object is used to set the priority for a SPVC connection request. It ranges between 1-16, with the following values: Best Priority = 1 Default Priority = … |
| 1.3.6.1.4.1.123.3.82.1.7.1.8 | ColumnnncCeSpvcMaxAdminWeight | read-create | current | This object is used to set a cost threshold for an SPVC connection. If the total cost of all VPCs exceeds this weight value for a given path, this SPVC will ch… |
| 1.3.6.1.4.1.123.3.82.1.7.1.9 | ColumnnncCeSpvcOperation | read-create | current | This object is used to request a reroute operation. Querying this object will not provide any useful information. |
| 1.3.6.1.4.1.123.3.82.1.7.1.10 | ColumnnncCeSpvcCallStatus | read-only | current | This read-only object is used to query the state of a particular SPVC. SPVCs that are connected and operational will return a value of 'connected', while those… |
| 1.3.6.1.4.1.123.3.82.1.7.1.11 | ColumnnncCeSpvcLocRerouteConfig | read-create | current | This object is used to configure the 'reroute on loss of continuity' feature using OAM-CC cells. For circuit emulation UNI side is not supported. It can be con… |
| 1.3.6.1.4.1.123.3.82.1.7.1.12 | ColumnnncCeSpvcFwdTmBucketOneRate | read-create | current | This object is for peak cell rate (PCR), the cell rate which the source may never exceed. It is used to determine which cells are 'excess'. Measured in Kb/s. R… |
| 1.3.6.1.4.1.123.3.82.1.7.1.13 | ColumnnncCeSpvcFwdTmBucketOneCdvt | read-create | current | This object is used to set cell delay variation tolerance (CDVT) for one endpoint, measured in microseconds. Range: 1 - 190,000 microseconds |
| 1.3.6.1.4.1.123.3.82.1.7.1.14 | ColumnnncCeSpvcBwdTmBucketOneRate | read-create | current | This object is for peak cell rate (PCR), the cell rate which the source may never exceed. It is used to determine which cells are 'excess'. Measured in Kb/s. R… |
| 1.3.6.1.4.1.123.3.82.1.7.1.15 | ColumnnncCeSpvcBwdTmBucketOneCdvt | read-create | current | This object is used to set cell delay variation tolerance (CDVT) for one endpoint, measured in microseconds. Range: 1 - 190,000 microseconds |
| 1.3.6.1.4.1.123.3.82.1.7.1.16 | ColumnnncCeSpvcCreator | read-only | current | The object retrieves the creator of a SPVC connection. |
| 1.3.6.1.4.1.123.3.82.1.7.1.17 | ColumnnncCeSpvcRowStatus | read-create | current | This object is used to control the status of a PDU and to query the status of an SPVC. When the RowStatus value is 'createAndWait', information for a row is ca… |
| 1.3.6.1.4.1.123.3.82.1.8 | TablenncCeSpvcDstCfgTable | not-accessible | current | the nncCeSpvcDstCfg table contains common objects used to configure, delete, modify and query the destination end point of an SPVC across different Alcatel CID… |
| 1.3.6.1.4.1.123.3.82.1.8.1 | RownncCeSpvcDstCfgTableEntry | not-accessible | current | An entry of nncCeSpvcDstCfgTable. |
| 1.3.6.1.4.1.123.3.82.1.8.1.1 | ColumnnncCeSpvcDstCfgCdvt | read-create | current | This object is used to set cell delay variation tolerance (CDVT) for one endpoint, measured in microseconds. Range: 1 - 190,000 microseconds |
| 1.3.6.1.4.1.123.3.82.1.8.1.2 | ColumnnncCeSpvcDstCfgLocRerouteConfig | read-create | current | This object is used to configure the 'reroute on loss of continuity' feature using OAM-CC cells. For circuit emulation UNI side is not supported. It can be con… |
| 1.3.6.1.4.1.123.3.82.1.8.1.3 | ColumnnncCeSpvcDstCfgRowStatus | read-create | current | This object is used to control the status of a PDU and to query the status of an SPVC. When the RowStatus value is 'createAndWait', information for a row is ca… |
| 1.3.6.1.4.1.123.3.82.3 | NodenncExtSpvcGroups | |||
| 1.3.6.1.4.1.123.3.82.3.1 | GroupnncCrSpvpcGroup | current | Common MIB objects for configuring a CR SPVPC source end-point across all Alcatel CID ATM platforms. | |
| 1.3.6.1.4.1.123.3.82.3.2 | GroupnncCrSpvpcDstCfgGroup | current | Common MIB objects for configuring a Cell Relay SPVPC destination end-point across all Alcatel CID ATM platforms. | |
| 1.3.6.1.4.1.123.3.82.3.3 | GroupnncCrSpvccGroup | current | Common MIB objects for configuring a CR SPVC source end-point across all Alcatel CID ATM platforms. | |
| 1.3.6.1.4.1.123.3.82.3.4 | GroupnncCrSpvccDstCfgGroup | current | Common MIB objects for configuring a Cell Relay SPVC destination end-point across all Alcatel CID ATM platforms. | |
| 1.3.6.1.4.1.123.3.82.3.5 | GroupnncFrSpvcGroup | current | Common MIB objects for configuring an SPVC using a Frame Relay source end-point across all Alcatel CID ATM platforms. | |
| 1.3.6.1.4.1.123.3.82.3.6 | GroupnncFrSpvcDstCfgGroup | current | Common MIB objects for configuring a Frame-Relay SPVC destination end-point across all Alcatel CID ATM platforms. | |
| 1.3.6.1.4.1.123.3.82.3.7 | GroupnncCeSpvcGroup | current | Common MIB objects for configuring a Circuit Emulation-based SPVC source end-point across all Alcatel CID ATM platforms. | |
| 1.3.6.1.4.1.123.3.82.3.8 | GroupnncCeSpvcDstCfgGroup | current | Common MIB objects for configuring a Circuit Emulation SPVC destination end-point across all Alcatel CID ATM platforms. | |
| 1.3.6.1.4.1.123.3.82.4 | NodenncExtSpvcCompliances | |||
| 1.3.6.1.4.1.123.3.82.4.1 | CompliancenncSpvcCompliance | current | The compliance statement for Alcatel CID SPVC MIB implementation. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| AtmFormatDisplay | OCTET STRING (SIZE (20)) | current | This display is for the ATM address prefix format. The following formats which are supported are displayed: DCC ATM Format |A | | | | | | | | | | | | | | | | | | | S| |F | DCC | HO-DSP | ESI | E| |I | | | | | | | | | | … |