OPTIX-PKT-PORT-MIB
398 objects
This mib specifies the port configuration information of device
Imported Objects
| OPTIX-BOARD-MANAGE-MIB | optixLogBoardId optixLogSubCardId |
| OPTIX-OID-MIB | optixProvisionPtn |
| OPTIX-PORT-MANAGE-MIB | optixPortId |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DateAndTime MacAddress RowStatus |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.10.4.50.52 | IdentityoptixPktPort | This mib specifies the port configuration information of device | ||
| 1.3.6.1.2.1.10.4.50.52.1 | NodeoptixPktPortGroup | |||
| 1.3.6.1.2.1.10.4.50.52.1.1 | TableoptixEthPortTable | not-accessible | current | This table contains basic configuration information of ETH port |
| 1.3.6.1.2.1.10.4.50.52.1.1.1 | RowoptixEthPortEntry | not-accessible | current | Entry containins basic configuration information of ETH port |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.1 | ColumnoptixEthPortId | not-accessible | current | This parameter specifies the eth port index |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.2 | ColumnoptixEthPortEncapType | read-create | current | This parameter specifies the eth port encaptype. 0: null, 1: cTag, 2: sTag, 3: iTag, 4: atm, 5: ppp |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.3 | ColumnoptixEthPortMtu | read-create | current | This parameter specifies the eth port MTU. Value range: 1518 to 9600. |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.4 | ColumnoptixEthPortWorkMode | read-create | current | This parameter specifies the eth port work mode. 0: auto, 1: snmp10mhalf, 2: snmp10mfull, 3: snmp100mhalf, 4: snmp100mfull, 5: snmp1000mhalf, 6: snmp1000mfull,… |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.5 | ColumnoptixEthPortEn | read-only | current | This parameter specifies the eth port phy enable. 0: disable, 1: enable |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.6 | ColumnoptixEthPortPtnWorkMode | read-only | current | This parameter specifies the eth port phy work mode. 0: auto, 1: snmp10mhalf, 2: snmp10mfull, 3: snmp100mhalf, 4: snmp100mfull, 5: snmp1000mhalf, 6: snmp1000mf… |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.7 | ColumnoptixEthPortPhyFCState | read-only | current | This parameter specifies the eth port phy flow control state. 0: disable, 1: enable, 2: send, 3: recv |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.8 | ColumnoptixEthPortPtnMacLoop | read-create | current | This parameter specifies the eth port mac loop type. 0: noloop, 1: inloop, 2: outloop |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.9 | ColumnoptixEthPortPtnPhyLoop | read-create | current | This parameter specifies the eth port phy loop type. 0: noloop, 1: inloop, 2: outloop |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.10 | ColumnoptixEthPortFcMode | read-create | current | This parameter specifies the eth port fc mode. 0: disable, 1: enable, 2: send, 3: recv |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.11 | ColumnoptixEthPortAutoFcMode | read-create | current | This parameter specifies the eth port fc mode auto. 0: disable, 1: asym, 2: sym, 3: asymSym |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.12 | ColumnoptixEthPortOpif | read-only | current | This parameter specifies the eth port opif type. 0: none, 1: singleMode, 2: multiMode, 3: electrical |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.13 | ColumnoptixEthPortSamplingId | read-only | current | This parameter specifies the eth port receive rate |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.14 | ColumnoptixEthPortRxRate | read-only | current | This parameter specifies the eth port receive rate |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.15 | ColumnoptixEthPortTxRate | read-only | current | This parameter specifies the eth port send rate |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.16 | ColumnoptixEthPortRealFc | read-only | current | This parameter specifies the eth port real fc mode result. 0: disable, 1: enable, 2: send, 3: recv |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.17 | ColumnoptixEthPortMdimode | read-create | current | This parameter specifies the eth port mdi mode. 0: mdix, 1: auto, 2: mdi |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.18 | ColumnoptixEthPortEnable | read-create | current | This parameter specifies the eth port enable. 0: disable, 1: enable |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.19 | ColumnoptixEthPortVlanId | read-create | current | This parameter specifies the eth port vlan ID. Value range: 0 to 4095. |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.20 | ColumnoptixEthPortVlanPri | read-create | current | This parameter specifies the eth port vlan pri. Value range: 0 to 7. A larger value indicates a higher priority. |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.21 | ColumnoptixEthPortTag | read-create | current | This parameter specifies the eth port tag. 0: access, 1: tagAware, 2: hybrid, 255: snmp0xff |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.22 | ColumnoptixEthPortQinqId | read-create | current | This parameter specifies the eth port qinq |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.23 | ColumnoptixEthPortMac | read-create | current | This parameter specifies the eth port mac address |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.24 | ColumnoptixEthPortLoopEn | read-create | current | This parameter specifies the eth port loop enable. 0: disable, 1: enable |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.25 | ColumnoptixEthPortBlockEn | read-create | current | This parameter specifies the eth port block after loop. 0: disable, 1: enable |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.26 | ColumnoptixEthPortWatchFlowEn | read-create | current | This parameter specifies the eth port watch flow enable. 0: disable, 1: enable |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.27 | ColumnoptixEthPortWatchFlowTime | read-create | current | This parameter specifies the eth port watch flow time |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.28 | ColumnoptixEthPortBroadBateenEn | read-create | current | This parameter specifies the eth port broadbateen enable. 0: disable, 1: enable |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.29 | ColumnoptixEthPortBroadBateen | read-create | current | This parameter specifies the eth port broadbateen |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.30 | ColumnoptixEthPortAutoneg | read-create | current | This parameter specifies the eth port autoneg. 1: snmp10mhalf, 2: snmp10mfull, 3: snmp100mhalf, 4: snmp100mfull, 5: snmp1000mhalf, 6: snmp1000mfull, 255: null |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.31 | ColumnoptixEthPortWatchRateEn | read-create | current | This parameter specifies the eth port watch rate enable. 0: disable, 1: enable |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.32 | ColumnoptixEthPortOpticalDir | read-only | current | This parameter specifies the eth port optical direction. 0: none, 1: sglfbr, 2: dblfbr |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.33 | ColumnoptixEthPortJitterEnableState | read-create | current | This parameter specifies the eth port enable status of jitter optimization. 0: disable, 1: enable |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.34 | ColumnoptixEthPortPhyErrDetectState | read-create | current | This parameter specifies the eth port enable status of PHY erroneous detection. 0: disable, 1: enable |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.35 | ColumnoptixEthPortErrorFlag | read-only | current | This parameter specifies the eth port flag of PHY mistake |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.36 | ColumnoptixEthPortLevelMode | read-create | current | This parameter specifies the eth port mode. 1: level1, 2: level2, 3: level3, 4: level2Level3 |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.37 | ColumnoptixEthPortUpDownStauts | read-only | current | This parameter specifies the up down status of port. 0: down, 1: up |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.38 | ColumnoptixHybridMinBandWidth | read-only | current | This parameter specifies hybrid port min bandwidth |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.39 | ColumnoptixHybridMaxBandWidth | read-only | current | This parameter specifies hybrid port max bandwidth |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.40 | ColumnoptixEthPortPoeEnable | read-create | current | This parameter specifies the eth port enable status of poe. 0: disable, 1: enable |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.41 | ColumnoptixEthPortRealPoeEnable | read-only | current | This parameter specifies the eth port real enable status of poe |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.42 | ColumnoptixHybridL3HoldOffTime | read-create | current | This parameter specifies hybrid port Hold off time |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.43 | ColumnoptixEthPortBerDetectState | read-create | current | This parameter indicates whether the bit error detection function is enabled. |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.44 | ColumnoptixEthPortPacketLostEXC | read-create | current | This parameter specifies the threshold of PacketLostEXC. |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.45 | ColumnoptixEthPortPacketLostSD | read-create | current | This parameter specifies the threshold of PacketLostSD. |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.46 | ColumnoptixEthPortBerSwitchState | read-create | current | This parameter indicates whether the bit-error-triggered switching is enabled. |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.47 | ColumnoptixEthPortBerSwitchType | read-create | current | This parameter indicates the type of the bit-error-triggered switching. |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.48 | ColumnoptixEthPortbdbateabsth | read-create | current | This object indicates the threshold of the broadcast packet suppression absolute value. |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.49 | ColumnoptixEthPortBwuSwatChenableState | read-create | current | This object indicates the enable status of monitoring port historical bandwidth usage. |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.50 | ColumnoptixEthPortPoeMode | read-create | current | This parameter specifies the PoE mode of the Ethernet port. 0: PoE; 1: PoE plus |
| 1.3.6.1.2.1.10.4.50.52.1.1.1.255 | ColumnoptixEthPortRowStatus | read-create | current | This parameter specifies the eth port row status |
| 1.3.6.1.2.1.10.4.50.52.1.2 | TableoptixVlanPortTable | not-accessible | current | This table contains basic configuration information of VLAN port |
| 1.3.6.1.2.1.10.4.50.52.1.2.1 | RowoptixVlanPortEntry | not-accessible | current | This table contains basic configuration information of VLAN port |
| 1.3.6.1.2.1.10.4.50.52.1.2.1.1 | ColumnoptixVlanPortId | not-accessible | current | This parameter specifies the VLAN port index. Value range: 0x2800 to 0x2FFF,0x9100 to 0x94FF. |
| 1.3.6.1.2.1.10.4.50.52.1.2.1.2 | ColumnoptixVlanPortVportType | read-create | current | This parameter specifies the virtual port type for VLAN ports. 1: eoa, 2: vlan, 3: eoadsl, 4: eoefm, 5: eoatm, 12: vlanif |
| 1.3.6.1.2.1.10.4.50.52.1.2.1.3 | ColumnoptixVlanPortBoardId | read-create | current | This parameter specifies the vlan port board id |
| 1.3.6.1.2.1.10.4.50.52.1.2.1.4 | ColumnoptixVlanPortSubID | read-create | current | This parameter specifies the vlan port subcard id |
| 1.3.6.1.2.1.10.4.50.52.1.2.1.5 | ColumnoptixVlanPortPortId | read-create | current | This parameter specifies the vlan port port id |
| 1.3.6.1.2.1.10.4.50.52.1.2.1.6 | ColumnoptixVlanPortVlan | read-create | current | This parameter specifies the vlan port vlan. Value range: 1 to 4094. |
| 1.3.6.1.2.1.10.4.50.52.1.2.1.7 | ColumnoptixVlanPortLevelMode | read-create | current | This parameter specifies the vlan port mode. 1: level1, 2: level2, 3: level3, 4: level2Level3 |
| 1.3.6.1.2.1.10.4.50.52.1.2.1.8 | ColumnoptixVlanIfPortVlan | read-create | current | This parameter specifies VLAN IDs configured for VLAN-IF member ports. Value range: 1 to 4094. |
| 1.3.6.1.2.1.10.4.50.52.1.2.1.255 | ColumnoptixVlanPortRowStatus | read-create | current | This parameter specifies the vlan port row status |
| 1.3.6.1.2.1.10.4.50.52.1.3 | TableoptixAtmPortTable | not-accessible | current | This table contains basic configuration information of ATM port |
| 1.3.6.1.2.1.10.4.50.52.1.3.1 | RowoptixAtmPortEntry | not-accessible | current | This table contains basic configuration information of ATM port |
| 1.3.6.1.2.1.10.4.50.52.1.3.1.1 | ColumnoptixAtmPortId | not-accessible | current | This parameter specifies the atm port id |
| 1.3.6.1.2.1.10.4.50.52.1.3.1.2 | ColumnoptixAtmPortLoop | read-create | current | This parameter specifies the atm port loop mode. 0: noloop, 1: inloop, 2: outloop |
| 1.3.6.1.2.1.10.4.50.52.1.3.1.3 | ColumnoptixAtmPortType | read-create | current | This parameter specifies the atm port type. 1: UNI, 2: NNI |
| 1.3.6.1.2.1.10.4.50.52.1.3.1.4 | ColumnoptixAtmPortCellEn | read-create | current | This parameter specifies the atm port cell enable. 0: disable, 1: enable |
| 1.3.6.1.2.1.10.4.50.52.1.3.1.5 | ColumnoptixAtmPortMinVpi | read-create | current | This parameter specifies the atm port min vpi. Value range: 0 to 0xfff and 0xffff. The value 0xffff indicates that the minimum value is not limited. This param… |
| 1.3.6.1.2.1.10.4.50.52.1.3.1.6 | ColumnoptixAtmPortMaxVpi | read-create | current | This parameter specifies the atm port max vpi. Value range: 0 to 0xfff and 0xffff. The value 0xffff indicates that the maximum value is not limited. This param… |
| 1.3.6.1.2.1.10.4.50.52.1.3.1.7 | ColumnoptixAtmPortMinVci | read-create | current | This parameter specifies the atm port min vci. Value range: 0 to 0xffff and 0xffffffff. The value 0xffffffff indicates that the minimum value is not limited. T… |
| 1.3.6.1.2.1.10.4.50.52.1.3.1.8 | ColumnoptixAtmPortMaxVci | read-create | current | This parameter specifies the atm port max vci Value range: 0 to 0xffff and 0xffffffff. The value 0xffffffff indicates that the maximum value is not limited. Th… |
| 1.3.6.1.2.1.10.4.50.52.1.3.1.9 | ColumnoptixAtmPortVccVpi | read-create | current | This paramater specifies the atm port vcc vpi. Value range fro OSN 1099/OSN 3900: 0 to 64. |
| 1.3.6.1.2.1.10.4.50.52.1.3.1.10 | ColumnoptixAtmPortEncapType | read-only | current | This parameter specifies the atm port encaptype. 0: null, 1: cTag, 2: sTag, 3: iTag, 4: atm, 5: ppp |
| 1.3.6.1.2.1.10.4.50.52.1.3.1.11 | ColumnoptixAtmPortLevelMode | read-create | current | This parameter specifies the Atm Port mode. 1: level1, 2: level2, 3: level3, 4: level2Level3 |
| 1.3.6.1.2.1.10.4.50.52.1.3.1.255 | ColumnoptixAtmPortRowStatus | read-create | current | This paramater specifies the atm port row status |
| 1.3.6.1.2.1.10.4.50.52.1.4 | TableoptixMLPPPTable | not-accessible | current | This table contains basic configuration information of ML-PPP |
| 1.3.6.1.2.1.10.4.50.52.1.4.1 | RowoptixMLPPPEntry | not-accessible | current | Entry containins basic configuration information of ML-PPP |
| 1.3.6.1.2.1.10.4.50.52.1.4.1.1 | ColumnoptixMLPPPId | not-accessible | current | This parameter specifies ML-PPP id |
| 1.3.6.1.2.1.10.4.50.52.1.4.1.2 | ColumnoptixMLPPPMinMemNum | read-create | current | This parameter specifies ML-PPP min member number |
| 1.3.6.1.2.1.10.4.50.52.1.4.1.3 | ColumnoptixMLPPPDelayCheckEn | read-create | current | This parameter specifies ML-PPP delay check enable. 0: disable, 1: enable, 255: none |
| 1.3.6.1.2.1.10.4.50.52.1.4.1.4 | ColumnoptixMLPPPDelay | read-create | current | This parameter specifies ML-PPP delay |
| 1.3.6.1.2.1.10.4.50.52.1.4.1.5 | ColumnoptixMLPPPBoardId | read-only | current | This parameter specifies ML-PPP board id |
| 1.3.6.1.2.1.10.4.50.52.1.4.1.6 | ColumnoptixMLPPPSubId | read-only | current | This parameter specifies ML-PPP subcard id |
| 1.3.6.1.2.1.10.4.50.52.1.4.1.7 | ColumnoptixMLPPPPortId | read-only | current | This parameter specifies ML-PPP port id |
| 1.3.6.1.2.1.10.4.50.52.1.4.1.8 | ColumnoptixMLPPPState | read-only | current | This parameter specifies ML-PPP state. 1: up, 2: down |
| 1.3.6.1.2.1.10.4.50.52.1.4.1.9 | ColumnoptixMLPPPNegotIp | read-only | current | This parameter specifies ML-PPP negot ip |
| 1.3.6.1.2.1.10.4.50.52.1.4.1.10 | ColumnoptixMLPPPNegotMask | read-only | current | This parameter specifies ML-PPP negot mask |
| 1.3.6.1.2.1.10.4.50.52.1.4.1.11 | ColumnoptixMLPPPSeqNumType | read-create | current | This parameter specifies ML-PPP SEQNUM type. 0: huawei, 1: short, 2: long |
| 1.3.6.1.2.1.10.4.50.52.1.4.1.12 | ColumnoptixMLPPPFragsize | read-create | current | This parameter specifies ML-PPP frag size |
| 1.3.6.1.2.1.10.4.50.52.1.4.1.13 | ColumnoptixMLPPPSendSpeed | read-only | current | This parameter specifies ML-PPP send speed |
| 1.3.6.1.2.1.10.4.50.52.1.4.1.14 | ColumnoptixMLPPPReciveSpeed | read-only | current | This parameter specifies ML-PPP recive speed |
| 1.3.6.1.2.1.10.4.50.52.1.4.1.15 | ColumnoptixMLPPPOSICPType | read-only | current | This parameter specifies ML-PPP OSICP type. 0: disable, 1: enable |
| 1.3.6.1.2.1.10.4.50.52.1.4.1.16 | ColumnoptixMLPPPMtu | read-create | current | This parameter specifies the MLPPP port MTU |
| 1.3.6.1.2.1.10.4.50.52.1.4.1.17 | ColumnoptixMLPPPLevelMode | read-create | current | This parameter specifies the MLPPP mode. 1: level1, 2: level2, 3: level3, 4: level2Level3 |
| 1.3.6.1.2.1.10.4.50.52.1.4.1.18 | ColumnoptixMLPPPResetState | read-create | current | This parameter specifies the MLPPP reset state. 0: null |
| 1.3.6.1.2.1.10.4.50.52.1.4.1.255 | ColumnoptixMLPPPRowStatus | read-create | current | This parameter specifies ML-PPP row status |
| 1.3.6.1.2.1.10.4.50.52.1.5 | TableoptixL3PortTable | not-accessible | current | This table contains basic configuration information of L3 Port |
| 1.3.6.1.2.1.10.4.50.52.1.5.1 | RowoptixL3PortEntry | not-accessible | current | Entry containins basic configuration information of L3 Port |
| 1.3.6.1.2.1.10.4.50.52.1.5.1.1 | ColumnoptixL3PortId | not-accessible | current | This parameter specifies the L3 port id |
| 1.3.6.1.2.1.10.4.50.52.1.5.1.2 | ColumnoptixL3PortIpMode | read-create | current | This parameter specifies the L3 port ip mode. 1: dsgt, 2: brwne, 3: brwpt |
| 1.3.6.1.2.1.10.4.50.52.1.5.1.3 | ColumnoptixL3PortIpAddr | read-create | current | This parameter specifies the L3 port ip address. Value range in in dotted decimal notation: 0.0.0.0 to 255.255.255.255. |
| 1.3.6.1.2.1.10.4.50.52.1.5.1.4 | ColumnoptixL3PortIpMask | read-create | current | This parameter specifies the L3 port ip mask. Value range in in dotted decimal notation: 0.0.0.0 to 255.255.255.255. |
| 1.3.6.1.2.1.10.4.50.52.1.5.1.5 | ColumnoptixL3PortBrwIpBoardId | read-create | current | This parameter specifies the L3 port ip borrow ip board id |
| 1.3.6.1.2.1.10.4.50.52.1.5.1.6 | ColumnoptixL3PortBrwIpSubId | read-create | current | This parameter specifies the L3 port ip borrow ip port id |
| 1.3.6.1.2.1.10.4.50.52.1.5.1.7 | ColumnoptixL3PortBrwIpPortId | read-create | current | This parameter specifies the L3 port ip borrow subbd id |
| 1.3.6.1.2.1.10.4.50.52.1.5.1.8 | ColumnoptixL3PortMplsEnable | read-create | current | This parameter specifies the L3 port mpls enable. 0: disable, 1: enable |
| 1.3.6.1.2.1.10.4.50.52.1.5.1.9 | ColumnoptixL3PortArpAgeTime | read-create | current | This parameter specifies the L3 port arp age time. Value range: 1 to 1440 (unit: minute) |
| 1.3.6.1.2.1.10.4.50.52.1.5.1.10 | ColumnoptixL3PortArpFullFlag | read-only | current | This parameter specifies the L3 port arp Full flag |
| 1.3.6.1.2.1.10.4.50.52.1.5.1.11 | ColumnoptixL3PortMtu | read-create | current | This parameter specifies the L3 port mtu. Value range:46 to 9600, default:1500 |
| 1.3.6.1.2.1.10.4.50.52.1.5.1.255 | ColumnoptixL3PortRowStatus | read-create | current | This parameter specifies the L3 port row status |
| 1.3.6.1.2.1.10.4.50.52.1.6 | TableoptixE1Table | not-accessible | current | This table contains configuration information of E1 port |
| 1.3.6.1.2.1.10.4.50.52.1.6.1 | RowoptixE1Entry | not-accessible | current | Entry containing configuration information of E1 port |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.1 | ColumnoptixE1PortId | not-accessible | current | This parameter specifies the E1 port id |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.2 | ColumnoptixE1RetimingMode | read-create | current | This parameter specifies E1 port retiming mode. 0: master, 1: slave, 2: line |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.3 | ColumnoptixE1LinkCode | read-create | current | This parameter specifies E1 port linkcode. 0: hdb3 |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.4 | ColumnoptixE1Frm | read-create | current | This parameter specifies E1 port frame struct. 0: unframe, 1: doubleFrame, 2: crc4Multiframe |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.5 | ColumnoptixE1Eq | read-only | current | This parameter specifies E1 port cable resistance value. 1: snmp75, 2: snmp120 |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.6 | ColumnoptixE1UserSlotNum | read-create | current | This parameter specifies E1 user slot number |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.7 | ColumnoptixE1Loop | read-create | current | This parameter specifies E1 port loop mode. 0: noloop, 1: inloop, 2: outloop |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.8 | ColumnoptixE1PrbsDir | read-create | current | This parameter specifies E1 port prbs dir. 0: UNI, 1: NNI |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.9 | ColumnoptixE1PrbsFrm | read-create | current | This parameter specifies E1 port prbs frm. 0: unFrame, 1: frame |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.10 | ColumnoptixE1TestType | read-create | current | This parameter specifies E1 port test type. 1: shortTerm, 2: longTerm, 3: longTerm |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.11 | ColumnoptixE1StartDataTime | read-only | current | This parameter specifies E1 port start data time |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.12 | ColumnoptixE1EndDataTime | read-only | current | This parameter specifies E1 port end data time |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.13 | ColumnoptixE1Progress | read-only | current | This parameter specifies E1 port progress. Value range: 1 to 100 (unit: %) |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.14 | ColumnoptixE1RealTestPeriod | read-only | current | This parameter specifies E1 port real test period |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.15 | ColumnoptixE1DataTypeNum | read-only | current | This parameter specifies E1 port data type number |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.16 | ColumnoptixE1Type1 | read-only | current | This parameter specifies E1 port type 1 |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.17 | ColumnoptixE1TestType2 | read-only | current | This parameter specifies E1 port type 2 |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.18 | ColumnoptixE1Result1 | read-only | current | This parameter specifies E1 port test result 1 |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.19 | ColumnoptixE1TestResult2 | read-only | current | This parameter specifies E1 port test result 2 |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.20 | ColumnoptixE1EncapType | read-create | current | This parameter specifies the e1 port encaptype. 0: null, 1: cTag, 2: sTag, 3: iTag, 4: atm, 5: ppp |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.21 | ColumnoptixE1Mtu | read-create | current | This parameter specifies the E1 MTU |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.22 | ColumnoptixE1LevelMode | read-create | current | This parameter specifies the E1 port mode. 1: level1, 2: level2, 3: level3, 4: level2Level3 |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.23 | ColumnoptixE1BittestPrbsDir | read-create | current | This parameter specifies E1 port prbs dir. 0: UNI, 1: NNI |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.24 | ColumnoptixE1BittestPrbsFrm | read-create | current | This parameter specifies E1 port prbs frm. 0: unFrame, 1: frame |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.25 | ColumnoptixE1BittestType | read-create | current | This parameter specifies the E1 port bittest type. 1: shortTerm, 2: longTerm, 3: longTerm |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.26 | ColumnoptixE1BittestStartDateTime | read-only | current | This parameter specifies the E1 port bittest date and time |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.27 | ColumnoptixE1BittestRealTestPeriod | read-only | current | This parameter specifies the E1 port bittest real test period |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.28 | ColumnoptixE1BittestStartPeriod | read-only | current | This parameter specifies the E1 port bittest start period |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.29 | ColumnoptixE1BittestTestResult1 | read-only | current | This parameter specifies the E1 port bittest result(part 1) |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.30 | ColumnoptixE1BittestTestResult2 | read-only | current | This parameter specifies the E1 port bittest result(part 2) |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.31 | ColumnoptixE1BittestTestResult3 | read-only | current | This parameter specifies the E1 port bittest result(part 3) |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.32 | ColumnoptixE1TestAction | read-create | current | This parameter specifies E1 port test set Begin time. 0: stop, 1: start, 255: null |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.33 | ColumnoptixE1TestTime | read-create | current | This parameter specifies E1 port test set End Time |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.34 | ColumnoptixE1TestType3 | read-only | current | This parameter specifies E1 port type 3. |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.35 | ColumnoptixE1TestResult3 | read-only | current | This parameter specifies E1 port test result 3 |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.36 | ColumnoptixE1TestType4 | read-only | current | This parameter specifies E1 port type 4 |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.37 | ColumnoptixE1TestResult4 | read-only | current | This parameter specifies E1 port test result 4 |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.38 | ColumnoptixE1TestType5 | read-only | current | This parameter specifies E1 port type 5 |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.39 | ColumnoptixE1TestResult5 | read-only | current | his parameter specifies E1 port test result 5 |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.40 | ColumnoptixE1TestType6 | read-only | current | This parameter specifies E1 port type 6 |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.41 | ColumnoptixE1TestResult6 | read-only | current | This parameter specifies E1 port test result 6 |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.42 | ColumnoptixE1BerTH | read-create | current | This object indicates the level of the upper BER threshold of E1 links. |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.43 | ColumnoptixE1AisCheck | read-create | current | This object indicates the status of the Ais alarm. |
| 1.3.6.1.2.1.10.4.50.52.1.6.1.255 | ColumnoptixE1RowStatus | read-create | current | This parameter specifies E1 port row status |
| 1.3.6.1.2.1.10.4.50.52.1.7 | TableoptixSPV4Table | not-accessible | current | This table contains configuration information of serial port |
| 1.3.6.1.2.1.10.4.50.52.1.7.1 | RowoptixSPV4Entry | not-accessible | current | Entry containing configuration information of serial port |
| 1.3.6.1.2.1.10.4.50.52.1.7.1.1 | ColumnoptixSPV4Id | not-accessible | current | This parameter specifies the serial port ID |
| 1.3.6.1.2.1.10.4.50.52.1.7.1.2 | ColumnoptixSPV4PortId | read-create | current | This parameter specifies physical port id |
| 1.3.6.1.2.1.10.4.50.52.1.7.1.3 | ColumnoptixSPV4Num | read-create | current | This parameter specifies serial port number |
| 1.3.6.1.2.1.10.4.50.52.1.7.1.4 | ColumnoptixSPV4List | read-create | current | This parameter specifies serial port list |
| 1.3.6.1.2.1.10.4.50.52.1.7.1.5 | ColumnoptixSPV4EncapType | read-create | current | This parameter specifies the specifies serial port encaptype. 0: null, 1: cTag, 2: sTag, 3: iTag, 4: atm, 5: ppp |
| 1.3.6.1.2.1.10.4.50.52.1.7.1.6 | ColumnoptixSPV4LevelMode | read-create | current | This parameter specifies the specifies serial port mode. 1: level1, 2: level2, 3: level3, 4: level2Level3 |
| 1.3.6.1.2.1.10.4.50.52.1.7.1.7 | ColumnoptixSPV4Mtu | read-create | current | This parameter specifies the SPV4 MTU |
| 1.3.6.1.2.1.10.4.50.52.1.7.1.255 | ColumnoptixSPV4RowStatus | read-create | current | This parameter specifies serial port row status |
| 1.3.6.1.2.1.10.4.50.52.1.8 | TableoptixSPVC12Table | not-accessible | current | This table contains configuration information of serial port vc12 |
| 1.3.6.1.2.1.10.4.50.52.1.8.1 | RowoptixSPVC12Entry | not-accessible | current | Entry containing configuration information of serial port vc12 |
| 1.3.6.1.2.1.10.4.50.52.1.8.1.1 | ColumnoptixSPVC12Id | not-accessible | current | This parameter sepcifies physical port of vc12 |
| 1.3.6.1.2.1.10.4.50.52.1.8.1.2 | ColumnoptixSPVC12HP | read-only | current | This parameter sepcifies HP of serial port vc12 |
| 1.3.6.1.2.1.10.4.50.52.1.8.1.3 | ColumnoptixSPVC12LP | read-only | current | This parameter sepcifies LP of serial port vc12 |
| 1.3.6.1.2.1.10.4.50.52.1.8.1.4 | ColumnoptixSPVC1264kNum | read-only | current | This parameter sepcifies 64k numbert of serial port vc 12 |
| 1.3.6.1.2.1.10.4.50.52.1.8.1.5 | ColumnoptixSPVC1264kList | read-only | current | This parameter sepcifies 64k list of serial port vc 12 |
| 1.3.6.1.2.1.10.4.50.52.1.8.1.255 | ColumnoptixSPVC12RowStatus | read-only | current | This parameter sepcifies SP VC12 row status |
| 1.3.6.1.2.1.10.4.50.52.1.9 | NodeoptixE1EventMember | |||
| 1.3.6.1.2.1.10.4.50.52.1.9.1 | ScalaroptixE1BIDTrapInfo | accessible-for-notify | current | This parameter specifies the E1 Board id |
| 1.3.6.1.2.1.10.4.50.52.1.9.2 | ScalaroptixE1SubIdTrapInfo | accessible-for-notify | current | This parameter specifies the E1 Sub id |
| 1.3.6.1.2.1.10.4.50.52.1.9.3 | ScalaroptixE1PIdTrapInfo | accessible-for-notify | current | This parameter specifies the E1 port id |
| 1.3.6.1.2.1.10.4.50.52.1.9.4 | ScalaroptixE1TimeStampTrapInfo | accessible-for-notify | current | This parameter specifies the E1 port id |
| 1.3.6.1.2.1.10.4.50.52.1.9.5 | ScalaroptixE1PRBSDIRTrapInfo | accessible-for-notify | current | This parameter specifies the E1 PRBS-DIR. 0: UNI, 1: NNI |
| 1.3.6.1.2.1.10.4.50.52.1.9.6 | ScalaroptixE1PRBSFRMTrapInfo | accessible-for-notify | current | This parameter specifies the E1 PRBS-FRM. 0: unFrame, 1: frame |
| 1.3.6.1.2.1.10.4.50.52.1.9.7 | ScalaroptixE1TestTypeTrapInfo | accessible-for-notify | current | This parameter specifies the E1 test Type. 1: shortTerm, 2: longTerm, 3: longTerm |
| 1.3.6.1.2.1.10.4.50.52.1.9.8 | ScalaroptixE1StartDataTimeTrapInfo | accessible-for-notify | current | This parameter specifies the E1 Start Data Time |
| 1.3.6.1.2.1.10.4.50.52.1.9.9 | ScalaroptixE1EndDataTimeTrapInfo | accessible-for-notify | current | This parameter specifies the E1 End Data Time |
| 1.3.6.1.2.1.10.4.50.52.1.9.10 | ScalaroptixE1ProressTrapInfo | accessible-for-notify | current | This parameter specifies the E1 Proress |
| 1.3.6.1.2.1.10.4.50.52.1.9.11 | ScalaroptixE1RealTestPeriodTrapInfo | accessible-for-notify | current | This parameter specifies the E1 Real Test Period |
| 1.3.6.1.2.1.10.4.50.52.1.9.12 | ScalaroptixE1DatatypeNumTrapInfo | accessible-for-notify | current | This parameter specifies the E1 DatatypeNum |
| 1.3.6.1.2.1.10.4.50.52.1.9.13 | ScalaroptixE1Type1TrapInfo | accessible-for-notify | current | This parameter specifies the E1 Type1 |
| 1.3.6.1.2.1.10.4.50.52.1.9.14 | ScalaroptixE1TestResult1TrapInfo | accessible-for-notify | current | This parameter specifies the E1 Test Result1 |
| 1.3.6.1.2.1.10.4.50.52.1.9.15 | ScalaroptixE1Type2TrapInfo | accessible-for-notify | current | This parameter specifies the E1 type2 |
| 1.3.6.1.2.1.10.4.50.52.1.9.16 | ScalaroptixE1TestResult2TrapInfo | accessible-for-notify | current | This parameter specifies the E1 test Reasult2 |
| 1.3.6.1.2.1.10.4.50.52.1.9.17 | ScalaroptixE1Type3TrapInfo | accessible-for-notify | current | This parameter specifies E1 port type 3. |
| 1.3.6.1.2.1.10.4.50.52.1.9.18 | ScalaroptixE1TestResult3TrapInfo | accessible-for-notify | current | This parameter specifies E1 port test result 3. |
| 1.3.6.1.2.1.10.4.50.52.1.9.19 | ScalaroptixE1Type4TrapInfo | accessible-for-notify | current | This parameter specifies E1 port type 4. |
| 1.3.6.1.2.1.10.4.50.52.1.9.20 | ScalaroptixE1TestResult4TrapInfo | accessible-for-notify | current | This parameter specifies E1 port test result 4. |
| 1.3.6.1.2.1.10.4.50.52.1.9.21 | ScalaroptixE1Type5TrapInfo | accessible-for-notify | current | This parameter specifies E1 port type 5. |
| 1.3.6.1.2.1.10.4.50.52.1.9.22 | ScalaroptixE1TestResult5TrapInfo | accessible-for-notify | current | This parameter specifies E1 port test result 5. |
| 1.3.6.1.2.1.10.4.50.52.1.9.23 | ScalaroptixE1Type6TrapInfo | accessible-for-notify | current | This parameter specifies E1 port type 6. |
| 1.3.6.1.2.1.10.4.50.52.1.9.24 | ScalaroptixE1TestResult6TrapInfo | accessible-for-notify | current | This parameter specifies E1 port test result 6. |
| 1.3.6.1.2.1.10.4.50.52.1.10 | NodeoptixE1Event | |||
| 1.3.6.1.2.1.10.4.50.52.1.10.1 | NotificationoptixE1Trap | current | This trap contains the bit error test event reported by E1 port. | |
| 1.3.6.1.2.1.10.4.50.52.1.11 | TableoptixAddMLPPPMemberTable | not-accessible | current | This table contains basic configuration information of ML-PPP |
| 1.3.6.1.2.1.10.4.50.52.1.11.1 | RowoptixAddMLPPPMemberEntry | not-accessible | current | Entry containins basic configuration information of ML-PPP |
| 1.3.6.1.2.1.10.4.50.52.1.11.1.1 | ColumnoptixAddMLPPPMemberMLPPPId | not-accessible | current | This parameter specifies ML-PPP id |
| 1.3.6.1.2.1.10.4.50.52.1.11.1.2 | ColumnoptixAddMLPPPMemberBoardId | not-accessible | current | This parameter specifies ML-PPP board id |
| 1.3.6.1.2.1.10.4.50.52.1.11.1.3 | ColumnoptixAddMLPPPMemberPortId | not-accessible | current | This parameter specifies ML-PPP port id |
| 1.3.6.1.2.1.10.4.50.52.1.11.1.5 | ColumnoptixAddMLPPPMemberSubId | not-accessible | current | This parameter specifies ML-PPP subcard id |
| 1.3.6.1.2.1.10.4.50.52.1.11.1.255 | ColumnoptixAddMLPPPMemberRowStatus | read-create | current | This parameter specifies ML-PPP row status |
| 1.3.6.1.2.1.10.4.50.52.1.12 | TableoptixVC12Table | not-accessible | current | This table contains configuration information of VC12 bit test |
| 1.3.6.1.2.1.10.4.50.52.1.12.1 | RowoptixVC12Entry | not-accessible | current | Entry containing configuration information of VC12 bit test |
| 1.3.6.1.2.1.10.4.50.52.1.12.1.1 | ColumnoptixVC12pid | not-accessible | current | Entry containing port id of VC12 bit test |
| 1.3.6.1.2.1.10.4.50.52.1.12.1.2 | ColumnoptixVC12HpId | not-accessible | current | This parameter specifies the VC4 id |
| 1.3.6.1.2.1.10.4.50.52.1.12.1.3 | ColumnoptixVC12LpId | not-accessible | current | This parameter specifies the VC12 id |
| 1.3.6.1.2.1.10.4.50.52.1.12.1.4 | ColumnoptixVC12PrbsDir | read-write | current | This parameter specifies bit test prbs dir. 0: UNI, 1: NNI |
| 1.3.6.1.2.1.10.4.50.52.1.12.1.5 | ColumnoptixVC12PrbsFrm | read-write | current | This parameter specifies bit test prbs frm. 0: unFrame, 1: frame |
| 1.3.6.1.2.1.10.4.50.52.1.12.1.6 | ColumnoptixVC12Action | read-write | current | This parameter specifies the bit test start control. 0: stop, 1: start, 255: invalid |
| 1.3.6.1.2.1.10.4.50.52.1.12.1.7 | ColumnoptixVC12Type | read-write | current | This parameter specifies the bit test type. 1: shortTerm, 2: longTerm, 3: longTerm |
| 1.3.6.1.2.1.10.4.50.52.1.12.1.8 | ColumnoptixVC12Time | read-write | current | This parameter specifies the bit test time. 0: invalid |
| 1.3.6.1.2.1.10.4.50.52.1.12.1.9 | ColumnoptixVC12StartDateTime | read-only | current | This parameter specifies the bit test start date time |
| 1.3.6.1.2.1.10.4.50.52.1.12.1.10 | ColumnoptixVC12RealTestPri | read-only | current | This parameter specifies the bit test real test period |
| 1.3.6.1.2.1.10.4.50.52.1.12.1.11 | ColumnoptixVC12StartPeriod | read-only | current | This parameter specifies the bit test start test period |
| 1.3.6.1.2.1.10.4.50.52.1.12.1.12 | ColumnoptixVC12Result1 | read-only | current | This parameter specifies the first part of bit test result |
| 1.3.6.1.2.1.10.4.50.52.1.12.1.13 | ColumnoptixVC12Result2 | read-only | current | This parameter specifies the second part of bit test result |
| 1.3.6.1.2.1.10.4.50.52.1.12.1.14 | ColumnoptixVC12Result3 | read-only | current | This parameter specifies the third part of bit test result |
| 1.3.6.1.2.1.10.4.50.52.1.13 | TableoptixCL2HTable | not-accessible | current | This table describes basic information about starting to capture headers of L2 packets. |
| 1.3.6.1.2.1.10.4.50.52.1.13.1 | RowoptixCL2HEntry | not-accessible | current | This entry contains basic configuration information of Start Capture Header of L2 Layer |
| 1.3.6.1.2.1.10.4.50.52.1.13.1.1 | ColumnoptixCL2HStart | read-write | current | This parameter indicates that capturing headers of L2 packets starts. |
| 1.3.6.1.2.1.10.4.50.52.1.13.1.2 | ColumnoptixCL2HMode | not-accessible | current | This parameter specifies a capture mode. |
| 1.3.6.1.2.1.10.4.50.52.1.13.1.3 | ColumnoptixCL2HNum | not-accessible | current | This parameter indicates the number of captured packets. |
| 1.3.6.1.2.1.10.4.50.52.1.13.1.4 | ColumnoptixCL2HLength | not-accessible | current | This parameter indicates the length of the packet header. |
| 1.3.6.1.2.1.10.4.50.52.1.13.1.5 | ColumnoptixCL2HDirection | not-accessible | current | This parameter specifies the direction in which packets' headers are captured. |
| 1.3.6.1.2.1.10.4.50.52.1.13.1.6 | ColumnoptixCL2HConditionMask | not-accessible | current | This parameter specifies a mask for header capturing conditions. |
| 1.3.6.1.2.1.10.4.50.52.1.13.1.7 | ColumnoptixCL2HSourceMAC | not-accessible | current | This parameter specifies a source MAC address. |
| 1.3.6.1.2.1.10.4.50.52.1.13.1.8 | ColumnoptixCL2HSourceMACWC | not-accessible | current | This parameter specifies a wildcard character for source MAC addresses. |
| 1.3.6.1.2.1.10.4.50.52.1.13.1.9 | ColumnoptixCL2HDestinationMAC | not-accessible | current | This parameter specifies a destination MAC address. |
| 1.3.6.1.2.1.10.4.50.52.1.13.1.10 | ColumnoptixCL2HDestinationMACWC | not-accessible | current | This parameter specifies a wildcard character for destination MAC addresses. |
| 1.3.6.1.2.1.10.4.50.52.1.13.1.11 | ColumnoptixCL2HOutVlan | not-accessible | current | This parameter specifies an outer VLAN ID. |
| 1.3.6.1.2.1.10.4.50.52.1.13.1.12 | ColumnoptixCL2HOutVlanWC | not-accessible | current | This parameter specifies a wildcard character for outer VLAN IDs. |
| 1.3.6.1.2.1.10.4.50.52.1.13.1.13 | ColumnoptixCL2HInnerVlan | not-accessible | current | This parameter specifies an inner VLAN ID. |
| 1.3.6.1.2.1.10.4.50.52.1.13.1.14 | ColumnoptixCL2HInnerVlanWC | not-accessible | current | This parameter specifies a wildcard character for inner VLAN IDs. |
| 1.3.6.1.2.1.10.4.50.52.1.13.1.15 | ColumnoptixCL2HEthernetType | not-accessible | current | This parameter specifies an Ethernet type. |
| 1.3.6.1.2.1.10.4.50.52.1.13.1.16 | ColumnoptixCL2HEthernetTypeWC | not-accessible | current | This parameter specifies a wildcard character for Ethernet types. |
| 1.3.6.1.2.1.10.4.50.52.1.13.1.17 | ColumnoptixCL2HAgeTime | not-accessible | current | This parameter specifies the aging time of capturing packet headers. |
| 1.3.6.1.2.1.10.4.50.52.1.13.1.18 | ColumnoptixCL2ProhdrStart | read-write | current | This parameter indicates that capturing headers of L2 protocol packets starts. |
| 1.3.6.1.2.1.10.4.50.52.1.13.1.19 | ColumnoptixCL2HOffSetIndex | read-write | current | This parameter indicates the offset index of capturing packet headers. |
| 1.3.6.1.2.1.10.4.50.52.1.13.1.20 | ColumnoptixCL2HMatchLength | read-write | current | This parameter specifies the match length of capturing packet headers. |
| 1.3.6.1.2.1.10.4.50.52.1.13.1.21 | ColumnoptixCL2HMatchRule | read-write | current | This parameter specifies the match rule of capturing packet headers. |
| 1.3.6.1.2.1.10.4.50.52.1.14 | TableoptixCL3HTable | not-accessible | current | This table describes basic information about starting to capture headers of L3 packets. |
| 1.3.6.1.2.1.10.4.50.52.1.14.1 | RowoptixCL3HEntry | not-accessible | current | This entry contains basic configuration information of Start Capture Header of L3 Layer |
| 1.3.6.1.2.1.10.4.50.52.1.14.1.1 | ColumnoptixCL3HStart | read-write | current | This parameter indicates that capturing headers of L3 packets starts. |
| 1.3.6.1.2.1.10.4.50.52.1.14.1.2 | ColumnoptixCL3HSrcIP | not-accessible | current | This parameter specifies a source IP address. |
| 1.3.6.1.2.1.10.4.50.52.1.14.1.3 | ColumnoptixCL3HSrcIPWC | not-accessible | current | This parameter specifies a wildcard character for source IP addresses. |
| 1.3.6.1.2.1.10.4.50.52.1.14.1.4 | ColumnoptixCL3HDestinationIP | not-accessible | current | This parameter specifies a destination IP address. |
| 1.3.6.1.2.1.10.4.50.52.1.14.1.5 | ColumnoptixCL3HDestinationIPWC | not-accessible | current | This parameter specifies a wildcard character for destination IP addresses. |
| 1.3.6.1.2.1.10.4.50.52.1.14.1.6 | ColumnoptixCL3HTOS | not-accessible | current | This parameter specifies a TOS. |
| 1.3.6.1.2.1.10.4.50.52.1.14.1.7 | ColumnoptixCL3HTOSWC | not-accessible | current | This parameter specifies a wildcard character for TOSs. |
| 1.3.6.1.2.1.10.4.50.52.1.14.1.8 | ColumnoptixCL3HProtocolType | not-accessible | current | This parameter specifies a protocol type. |
| 1.3.6.1.2.1.10.4.50.52.1.14.1.9 | ColumnoptixCL3HProtocolTypeWC | not-accessible | current | This parameter specifies a wildcard character for protocol types. |
| 1.3.6.1.2.1.10.4.50.52.1.14.1.10 | ColumnoptixCL3HICMPType | not-accessible | current | This parameter specifies an ICMP type. |
| 1.3.6.1.2.1.10.4.50.52.1.14.1.11 | ColumnoptixCL3HICMPTypeWC | not-accessible | current | This parameter specifies a wildcard character for ICMP types. |
| 1.3.6.1.2.1.10.4.50.52.1.14.1.12 | ColumnoptixCL3HTCPSrcPortID | not-accessible | current | This parameter specifies the ID of a TCP source port. |
| 1.3.6.1.2.1.10.4.50.52.1.14.1.13 | ColumnoptixCL3HTCPSrcPortIDWC | not-accessible | current | This parameter specifies a wildcard character for IDs of TCP source ports. |
| 1.3.6.1.2.1.10.4.50.52.1.14.1.14 | ColumnoptixCL3HTCPDstPortID | not-accessible | current | This parameter specifies the ID of a TCP destination port. |
| 1.3.6.1.2.1.10.4.50.52.1.14.1.15 | ColumnoptixCL3HTCPDstPortIDWC | not-accessible | current | This parameter specifies a wildcard character for IDs of TCP destination ports. |
| 1.3.6.1.2.1.10.4.50.52.1.14.1.16 | ColumnoptixCL3HOffSetIndex | read-write | current | This parameter indicates the offset index of capturing packet headers. |
| 1.3.6.1.2.1.10.4.50.52.1.14.1.17 | ColumnoptixCL3HMatchLength | read-write | current | This parameter specifies the match length of capturing packet headers. |
| 1.3.6.1.2.1.10.4.50.52.1.14.1.18 | ColumnoptixCL3HMatchRule | read-write | current | This parameter specifies the match rule of capturing packet headers. |
| 1.3.6.1.2.1.10.4.50.52.1.15 | TableoptixPortCaptureHeaderTable | not-accessible | current | This table describes basic information about stopping packet header capturing on a port. |
| 1.3.6.1.2.1.10.4.50.52.1.15.1 | RowoptixPortCaptureHeaderEntry | not-accessible | current | This entry describes basic information about stopping packet header capturing on a port. |
| 1.3.6.1.2.1.10.4.50.52.1.15.1.1 | ColumnoptixPortCaptureHeaderStop | read-write | current | This parameter indicates that packet header capturing stops on a port. |
| 1.3.6.1.2.1.10.4.50.52.1.15.1.2 | ColumnoptixPortCapHeaderStopType | read-write | current | This parameter indicates the type of captured packets. |
| 1.3.6.1.2.1.10.4.50.52.1.15.1.3 | ColumnoptixPortCapHeaderStopDirect | read-write | current | This parameter indicates the direction of captured packets on a port. |
| 1.3.6.1.2.1.10.4.50.52.1.16 | NodeoptixETHMgrPacketEventMember | |||
| 1.3.6.1.2.1.10.4.50.52.1.16.1 | ScalaroptixETHMgrPacketBIDTrapInfo | accessible-for-notify | current | This parameter specifies the board ID of an Ethernet port. |
| 1.3.6.1.2.1.10.4.50.52.1.16.2 | ScalaroptixETHMgrPacketSubIDTrapInfo | accessible-for-notify | current | This parameter specifies the subboard ID of an Ethernet port. |
| 1.3.6.1.2.1.10.4.50.52.1.16.3 | ScalaroptixETHMgrPacketPIDTrapInfo | accessible-for-notify | current | This parameter specifies the ID of an Ethernet port. |
| 1.3.6.1.2.1.10.4.50.52.1.16.4 | ScalaroptixETHMgrPacketAllNumTrapInfo | accessible-for-notify | current | This parameter indicates the number of packets captured by the chip. |
| 1.3.6.1.2.1.10.4.50.52.1.16.5 | ScalaroptixETHMgrPacketHeadNumTrapInfo | accessible-for-notify | current | This parameter indicates the number of captured packet headers. |
| 1.3.6.1.2.1.10.4.50.52.1.16.6 | ScalaroptixETHMgrPacketEndTagTrapInfo | accessible-for-notify | current | This parameter specifies a flag for the ending of packet capturing. |
| 1.3.6.1.2.1.10.4.50.52.1.16.7 | ScalaroptixETHMgrPacketHeadLenTrapInfo | accessible-for-notify | current | This parameter indicates the length of the packet header. |
| 1.3.6.1.2.1.10.4.50.52.1.16.8 | ScalaroptixETHMgrPacketPayload | accessible-for-notify | current | This parameter indicates the packet payload. |
| 1.3.6.1.2.1.10.4.50.52.1.16.9 | ScalaroptixETHMgrPacketTypeTrapInfo | accessible-for-notify | current | This parameter specifies the packet type of captured packets. |
| 1.3.6.1.2.1.10.4.50.52.1.16.10 | ScalaroptixETHMgrPacketDirectTrapInfo | accessible-for-notify | current | This parameter specifies the direction of captured packets on a port. |
| 1.3.6.1.2.1.10.4.50.52.1.17 | ScalaroptixNeCaptureHeaderStop | read-write | current | This parameter specifies whether packet header capturing on an entire NE is stopped. |
| 1.3.6.1.2.1.10.4.50.52.1.18 | NodeoptixETHMgrPacketEvent | |||
| 1.3.6.1.2.1.10.4.50.52.1.18.1 | NotificationoptixETHMgrPacketTrap | current | This trap describes the packet header capturing event. | |
| 1.3.6.1.2.1.10.4.50.52.1.19 | NodeoptixPktPortLogicStateChangeTrapMember | |||
| 1.3.6.1.2.1.10.4.50.52.1.19.1 | ScalaroptixPktPortLogicStateBID | accessible-for-notify | current | This object indicates the slot ID. |
| 1.3.6.1.2.1.10.4.50.52.1.19.2 | ScalaroptixPktPortLogicStatesubBID | accessible-for-notify | current | This object indicates the subcard ID. |
| 1.3.6.1.2.1.10.4.50.52.1.19.3 | ScalaroptixPktPortLogicStatePID | accessible-for-notify | current | This object indicates the port ID. |
| 1.3.6.1.2.1.10.4.50.52.1.19.4 | ScalaroptixPktPortLogicStateChange | accessible-for-notify | current | This object indicates the change state. |
| 1.3.6.1.2.1.10.4.50.52.1.20 | TableoptixPerAlmTHTable | not-accessible | current | This table contains basic configuration of the optical power threshold. |
| 1.3.6.1.2.1.10.4.50.52.1.20.1 | RowoptixPerAlmTHEntry | not-accessible | current | This entry contains basic configuration of the optical power threshold. |
| 1.3.6.1.2.1.10.4.50.52.1.20.1.1 | ColumnoptixPerAlmTHPathID | not-accessible | current | This object specifies the path ID. |
| 1.3.6.1.2.1.10.4.50.52.1.20.1.2 | ColumnoptixPerAlmTHtype | not-accessible | current | This object specifies the performance ID. |
| 1.3.6.1.2.1.10.4.50.52.1.20.1.3 | ColumnoptixPerAlmTHhigh | read-write | current | This object specifies the upper threshold. |
| 1.3.6.1.2.1.10.4.50.52.1.20.1.4 | ColumnoptixPerAlmTHLow | read-write | current | This object specifies the lower threshold. |
| 1.3.6.1.2.1.10.4.50.52.1.21 | NodeoptixPktPortLogicStateChangeEvent | |||
| 1.3.6.1.2.1.10.4.50.52.1.21.1 | NotificationoptixPktPortLogicStateChangeTrap | current | This trap describes the logical status event information of a port. | |
| 1.3.6.1.2.1.10.4.50.52.1.22 | TableoptixPktPortbwuswatchfluxTable | not-accessible | current | This table contains the historical bandwidth usage of ports. |
| 1.3.6.1.2.1.10.4.50.52.1.22.1 | RowoptixPktPortbwuswatchfluxEntry | not-accessible | current | This entry contains the historical bandwidth usage of ports. |
| 1.3.6.1.2.1.10.4.50.52.1.22.1.1 | ColumnoptixPktPortbwuStartTime | not-accessible | current | This object indicates the historical bandwidth usage of a port. |
| 1.3.6.1.2.1.10.4.50.52.1.22.1.2 | ColumnoptixPktPortbwuEndTime | not-accessible | current | This object indicates the end time of port historical bandwidth use. |
| 1.3.6.1.2.1.10.4.50.52.1.22.1.3 | ColumnoptixPktPortbwuTimelist | not-accessible | current | This object indicates the list of port historical bandwidth usage. |
| 1.3.6.1.2.1.10.4.50.52.1.22.1.4 | ColumnoptixPktPortbwurealStartTime | read-only | current | This object indicates the start time of port historical bandwidth use. |
| 1.3.6.1.2.1.10.4.50.52.1.22.1.5 | ColumnoptixPktPortbwuDataFlag | read-only | current | This object indicates whether the port historical bandwidth usage data is available. 0: No usage data is available; 1: Usage data is available. |
| 1.3.6.1.2.1.10.4.50.52.1.22.1.6 | ColumnoptixPktPortbwuRxDataUS | read-only | current | This object indicates the receive-end data of port historical bandwidth usage. |
| 1.3.6.1.2.1.10.4.50.52.1.22.1.7 | ColumnoptixPktPortbwuTxDataUS | read-only | current | This object indicates the transmit-end data of port historical bandwidth usage. |
| 1.3.6.1.2.1.10.4.50.52.1.23 | TableoptixPktPortBWWatchFluxTable | not-accessible | current | This table describes the historical physical traffic of ports. |
| 1.3.6.1.2.1.10.4.50.52.1.23.1 | RowoptixPktPortBWWatchFluxEntry | not-accessible | current | This entry describes the historical physical traffic of ports. |
| 1.3.6.1.2.1.10.4.50.52.1.23.1.1 | ColumnoptixPktPortBWRealStartTime | read-only | current | This object indicates the start time of port historical physical flow. |
| 1.3.6.1.2.1.10.4.50.52.1.23.1.2 | ColumnoptixPktPortBWDataFlag | read-only | current | This object indicates whether the port historical physical flow is available. 0: No usage data is available; 1: Usage data is available. |
| 1.3.6.1.2.1.10.4.50.52.1.23.1.3 | ColumnoptixPktPortBWRxDataUS | read-only | current | This object indicates the receive-end data of port historical physical flow . |
| 1.3.6.1.2.1.10.4.50.52.1.23.1.4 | ColumnoptixPktPortBWTxDataUS | read-only | current | This object indicates the transmit-end data of port historical physical flow. |
| 1.3.6.1.2.1.10.4.50.52.1.24 | TableoptixPktPortRMONWatchFluxTable | not-accessible | current | This table describes the traffic of ports at any given time. |
| 1.3.6.1.2.1.10.4.50.52.1.24.1 | RowoptixPktPortRMONWatchFluxEntry | not-accessible | current | This entry describes the traffic of ports at any given time. |
| 1.3.6.1.2.1.10.4.50.52.1.24.1.1 | ColumnoptixPktPortRMONRealStartTime | read-only | current | This object indicates the start time of port flow. |
| 1.3.6.1.2.1.10.4.50.52.1.24.1.2 | ColumnoptixPktPortRMONDataFlag | read-only | current | This object indicates whether the port flow is available. 0: No usage data is available; 1: Usage data is available. |
| 1.3.6.1.2.1.10.4.50.52.1.24.1.3 | ColumnoptixPktPortRMONRxDataUS | read-only | current | This object indicates the receive-end data of port flow . |
| 1.3.6.1.2.1.10.4.50.52.1.24.1.4 | ColumnoptixPktPortRMONTxDataUS | read-only | current | This object indicates the transmit-end data of port flow. |
| 1.3.6.1.2.1.10.4.50.52.1.25 | TableoptixEthPortExtTable | not-accessible | current | This table contains basic configuration information of an ETH port. |
| 1.3.6.1.2.1.10.4.50.52.1.25.1 | RowoptixEthPortExtEntry | not-accessible | current | This entry contains basic configuration information of an ETH port. |
| 1.3.6.1.2.1.10.4.50.52.1.25.1.1 | ColumnoptixEthPortholdupstate | read-write | current | This parameter specifies the forcible-up state of an ETH port. 0: disable, 1: enable |
| 1.3.6.1.2.1.10.4.50.52.1.25.1.2 | ColumnoptixEthPortRemarkstate | read-write | current | This parameter specifies the demapping enable status of an ETH port.0:disable,1:enable |
| 1.3.6.1.2.1.10.4.50.52.1.25.1.3 | ColumnoptixEthPortAutoBroadBaTh | read-write | current | This parameter indicates the threshold (%) for automatic broadcast packet suppression of PWs. |
| 1.3.6.1.2.1.10.4.50.52.1.25.1.4 | ColumnoptixEthPortAutoBroadBaRealTh | read-only | current | This parameter indicates the actual threshold (%) for automatic broadcast packet suppression of PWs. |
| 1.3.6.1.2.1.10.4.50.52.1.25.1.5 | ColumnoptixEthPortAutoBroadBaRealEn | read-only | current | This parameter indicates whether automatic broadcast packet suppression is enabled for PWs. |
| 1.3.6.1.2.1.10.4.50.52.1.25.1.6 | ColumnoptixEthPortUniDirMode | read-write | current | This parameter indicates whether unidirectional operation is enabled for 10G port.0:disable,1:enable. |
| 1.3.6.1.2.1.10.4.50.52.1.25.1.7 | ColumnoptixEthPortDefForwardType | read-write | current | This parameter indicates the default forwarding queue priority of ETH ports. Its value is an integer: cs7 (1), cs6 (2), ef (3), af4 (4), af3 (5), af2 (6), af1 … |
| 1.3.6.1.2.1.10.4.50.52.1.25.1.8 | ColumnoptixEthPortPacketColor | read-write | current | This parameter indicates the default packet color of an ETH-port forwarding queue: red(1), yellow (2), or green (3). |
| 1.3.6.1.2.1.10.4.50.52.1.25.1.9 | ColumnoptixEthPortLagLinkAggrePortPri | read-write | current | This object indicates the priority of the L2 LAG slave port. Value range: 0 to 0xffffffff. |
| 1.3.6.1.2.1.10.4.50.52.1.25.1.10 | ColumnoptixEthPortBwwatchEnable | read-write | current | This object indicates the enable status of monitoring port physical bandwidth usage. |
| 1.3.6.1.2.1.10.4.50.52.1.25.1.11 | ColumnoptixEthPortDelayWatchEn | read-write | current | This object indicates the enable status of accurate expansion. 0: disable, 1: enable |
| 1.3.6.1.2.1.10.4.50.52.1.25.1.12 | ColumnoptixEthPortWaveWorkBand | read-only | current | This parameter is used to query the working band wavelength of a laser. |
| 1.3.6.1.2.1.10.4.50.52.1.25.1.13 | ColumnoptixEthPortGetWaveNum | read-only | current | This parameter is used to query the number of operating wavelengths of a laser. |
| 1.3.6.1.2.1.10.4.50.52.1.26 | TableoptixAtomGpsPortTable | not-accessible | current | This table contains basic configuration information of the GPS port. |
| 1.3.6.1.2.1.10.4.50.52.1.26.1 | RowoptixAtomGpsPortEntry | not-accessible | current | This entry contains basic configuration information of the GPS port. |
| 1.3.6.1.2.1.10.4.50.52.1.26.1.1 | ColumnoptixAtomGpsPortPtpDomainId | read-write | current | This parameter specifies the domain ID of an IEEE 1588 packet sent over the GPS port. |
| 1.3.6.1.2.1.10.4.50.52.1.26.1.2 | ColumnoptixAtomGpsPortPtpPri1 | read-write | current | This parameter specifies priority 1 of an IEEE 1588 packet sent over the GPS port. |
| 1.3.6.1.2.1.10.4.50.52.1.26.1.3 | ColumnoptixAtomGpsPortPtpPri2 | read-write | current | This parameter specifies priority 2 of an IEEE 1588 packet sent over the GPS port. |
| 1.3.6.1.2.1.10.4.50.52.1.26.1.4 | ColumnoptixAtomGpsPortTimeYear | read-only | current | This parameter specifies the year of the GPS port time. |
| 1.3.6.1.2.1.10.4.50.52.1.26.1.5 | ColumnoptixAtomGpsPortTimeMonth | read-only | current | This parameter specifies the month of the GPS port time. |
| 1.3.6.1.2.1.10.4.50.52.1.26.1.6 | ColumnoptixAtomGpsPortTimeDay | read-only | current | This parameter specifies the day of the GPS port time. |
| 1.3.6.1.2.1.10.4.50.52.1.26.1.7 | ColumnoptixAtomGpsPortTimeHour | read-only | current | This parameter specifies the hour of the GPS port time. |
| 1.3.6.1.2.1.10.4.50.52.1.26.1.8 | ColumnoptixAtomGpsPortTimeMinute | read-only | current | This parameter specifies the minute of the GPS port time. |
| 1.3.6.1.2.1.10.4.50.52.1.26.1.9 | ColumnoptixAtomGpsPortTimeSecond | read-only | current | This parameter specifies the second of the GPS port time. |
| 1.3.6.1.2.1.10.4.50.52.1.26.1.10 | ColumnoptixAtomGpsPortTimeLockState | read-only | current | This parameter specifies the time locking status of the GPS port. |
| 1.3.6.1.2.1.10.4.50.52.1.26.1.11 | ColumnoptixAtomGpsPortLliteNum | read-only | current | This parameter specifies the number of satellites available for the GPS port. |
| 1.3.6.1.2.1.10.4.50.52.1.26.1.12 | ColumnoptixAtomGpsPortLliteId | read-only | current | This parameter specifies the satellite ID of the GPS port. |
| 1.3.6.1.2.1.10.4.50.52.1.26.1.13 | ColumnoptixAtomGpsPortLliteRatio | read-only | current | This parameter specifies the satellite SNR of the GPS port. |
| 1.3.6.1.2.1.10.4.50.52.1.26.1.14 | ColumnoptixAtomGpsPortSelfHealEn | read-write | current | This parameter specifies whether the self-healing of the GPS port is enabled. |
| 1.3.6.1.2.1.10.4.50.52.1.26.1.15 | ColumnoptixAtomGpsPortFreqLockState | read-only | current | This parameter specifies the frequency locking status of the GPS port. |
| 1.3.6.1.2.1.10.4.50.52.1.26.1.16 | ColumnoptixAtomGpsPortReStart | read-write | current | This parameter specifies the row status of the GPS port. |
| 1.3.6.1.2.1.10.4.50.52.1.27 | TableoptixVlanIfMemberTable | not-accessible | current | This table contains basic configuration information about VLAN-IF member ports. |
| 1.3.6.1.2.1.10.4.50.52.1.27.1 | RowoptixVlanIfMemberEntry | not-accessible | current | The entry contains basic configuration information about VLAN-IF member ports. |
| 1.3.6.1.2.1.10.4.50.52.1.27.1.1 | ColumnoptixVlanIfMemberBid | not-accessible | current | This parameter specifies the slot ID of the board providing VLAN-IF member ports. |
| 1.3.6.1.2.1.10.4.50.52.1.27.1.2 | ColumnoptixVlanIfMemberSubId | not-accessible | current | This parameter specifies the subboard ID of the board providing VLAN-IF member ports. |
| 1.3.6.1.2.1.10.4.50.52.1.27.1.3 | ColumnoptixVlanIfMemberPid | not-accessible | current | This parameter specifies the ID of VLAN-IF member ports. |
| 1.3.6.1.2.1.10.4.50.52.1.27.1.255 | ColumnoptixVlanIfMemberRowStatus | read-create | current | This parameter specifies row status of VLAN-IF member ports. |
| 1.3.6.1.2.1.10.4.50.52.1.28 | TableoptixEthPortCaptureHeaderTable | not-accessible | current | This table describes basic information about captured packet headers. |
| 1.3.6.1.2.1.10.4.50.52.1.28.1 | RowoptixEthPortCaptureHeaderEntry | not-accessible | current | This entry contains basic configuration information about captured packet headers. |
| 1.3.6.1.2.1.10.4.50.52.1.28.1.1 | ColumnoptixEthPortCaptureHeaderBId | not-accessible | current | This parameter specifies the board ID of an Ethernet port. |
| 1.3.6.1.2.1.10.4.50.52.1.28.1.2 | ColumnoptixEthPortCaptureHeaderSubId | not-accessible | current | This parameter specifies the subboard ID of an Ethernet port. |
| 1.3.6.1.2.1.10.4.50.52.1.28.1.3 | ColumnoptixEthPortCaptureHeaderPortId | not-accessible | current | This parameter specifies the ID of an Ethernet port. |
| 1.3.6.1.2.1.10.4.50.52.1.28.1.4 | ColumnoptixEthPortCaptureHeaderDigType | not-accessible | current | This parameter indicates the type of captured packets.{service(0),protocol(1),all(255)} |
| 1.3.6.1.2.1.10.4.50.52.1.28.1.5 | ColumnoptixEthPortCaptureHeaderHeadDir | not-accessible | current | This parameter specifies the direction in which packet headers are captured.{ingress(0),egress(1),all(255)} |
| 1.3.6.1.2.1.10.4.50.52.1.28.1.6 | ColumnoptixEthPortCaptureHeaderType | read-only | current | This parameter specifies the packet type of captured packets.{l2captureheader(0),l3captureheader(1),l2procaptureheader(2),l2l3captureheader(3) |
| 1.3.6.1.2.1.10.4.50.52.1.28.1.7 | ColumnoptixEthPortCaptureHeaderMode | read-only | current | This parameter indicates the mode of captured packets.{once(0),continuance(1)} |
| 1.3.6.1.2.1.10.4.50.52.1.28.1.8 | ColumnoptixEthPortCaptureHeaderHeadNum | read-only | current | This parameter indicates the number of captured packets. |
| 1.3.6.1.2.1.10.4.50.52.1.28.1.9 | ColumnoptixEthPortCaptureHeaderHeadLen | read-only | current | This parameter indicates the length of the packet header. |
| 1.3.6.1.2.1.10.4.50.52.1.28.1.10 | ColumnoptixEthPortCaptureHeaderAgeTime | read-only | current | This parameter specifies the aging time of capturing packet headers. |
| 1.3.6.1.2.1.10.4.50.52.1.28.1.11 | ColumnoptixEthPortCaptureHeaderMask | read-only | current | This parameter specifies a mask code of capturing packet headers. |
| 1.3.6.1.2.1.10.4.50.52.1.28.1.12 | ColumnoptixEthPortCaptureHeaderRule | read-only | current | This parameter indicates the rule of capturing packet headers. |
| 1.3.6.1.2.1.10.4.50.52.1.28.1.13 | ColumnoptixEthPortCaphdrOffset | read-only | current | This parameter indicates the offset index of capturing packet headers. |
| 1.3.6.1.2.1.10.4.50.52.1.28.1.14 | ColumnoptixEthPortCaphdrMatchLen | read-only | current | This parameter specifies the match length of capturing packet headers. |
| 1.3.6.1.2.1.10.4.50.52.1.28.1.15 | ColumnoptixEthPortCaphdrMatchRule | read-only | current | This parameter specifies the match rule of capturing packet headers. |
| 1.3.6.1.2.1.10.4.50.52.1.29 | TableoptixDelayWatchTable | not-accessible | current | This table describes the information about accurate expansion. |
| 1.3.6.1.2.1.10.4.50.52.1.29.1 | RowoptixDelayWatchEntry | not-accessible | current | This entry contains the information about accurate expansion. |
| 1.3.6.1.2.1.10.4.50.52.1.29.1.1 | ColumnoptixDelayWatchStartTime | not-accessible | current | This parameter is used to query the start time of accurate expansion delay information. |
| 1.3.6.1.2.1.10.4.50.52.1.29.1.2 | ColumnoptixDelayWatchEndTime | not-accessible | current | This parameter is used to query the end time of accurate expansion delay information. |
| 1.3.6.1.2.1.10.4.50.52.1.29.1.3 | ColumnoptixDelayWatchTimelist | not-accessible | current | This parameter is used to query the number of accurate expansion delay information. |
| 1.3.6.1.2.1.10.4.50.52.1.29.1.4 | ColumnoptixDelayWatchrealStartTime | read-only | current | This parameter is used to query the actual start time of the accurate expansion delay information. |
| 1.3.6.1.2.1.10.4.50.52.1.29.1.5 | ColumnoptixDelayWatchDataFlag | read-only | current | This parameter is used to check for delay data in accurate expansion. 0-no delay data, 1-delay data |
| 1.3.6.1.2.1.10.4.50.52.1.29.1.6 | ColumnoptixDelayWatchDelayMax | read-only | current | This parameter is used to query the maximum delay of accurate expansion. |
| 1.3.6.1.2.1.10.4.50.52.1.29.1.7 | ColumnoptixDelayWatchDelayAvg | read-only | current | This parameter is used to query the average delay of accurate expansion. |
| 1.3.6.1.2.1.10.4.50.52.1.29.1.8 | ColumnoptixDelayWatchDelayInfo1 | read-only | current | This parameter is used to query the percentage of < 1 ms delay distributions. |
| 1.3.6.1.2.1.10.4.50.52.1.29.1.9 | ColumnoptixDelayWatchDelayInfo2 | read-only | current | This parameter is used to query the percentage of 1-2 ms delay distributions. |
| 1.3.6.1.2.1.10.4.50.52.1.29.1.10 | ColumnoptixDelayWatchDelayInfo3 | read-only | current | This parameter is used to query the percentage of 2-4 ms delay distributions. |
| 1.3.6.1.2.1.10.4.50.52.1.29.1.11 | ColumnoptixDelayWatchDelayInfo4 | read-only | current | This parameter is used to query the percentage of 4-6 ms delay distributions. |
| 1.3.6.1.2.1.10.4.50.52.1.29.1.12 | ColumnoptixDelayWatchDelayInfo5 | read-only | current | This parameter is used to query the percentage of 6-10 ms delay distributions. |
| 1.3.6.1.2.1.10.4.50.52.1.29.1.13 | ColumnoptixDelayWatchDelayInfo6 | read-only | current | This parameter is used to query the percentage of 10-15 ms delay distributions. |
| 1.3.6.1.2.1.10.4.50.52.1.29.1.14 | ColumnoptixDelayWatchDelayInfo7 | read-only | current | This parameter is used to query the percentage of 15-20 ms delay distributions. |
| 1.3.6.1.2.1.10.4.50.52.1.29.1.15 | ColumnoptixDelayWatchDelayInfo8 | read-only | current | This parameter is used to query the percentage of > 20 ms delay distributions. |