PW-CEP-MIB
154 objects
This MIB contains managed object definitions for Circuit Emulation over Packet (CEP) as in: Malis, A., Johnson, T., Zelig, D., and Martini, L. 'SONET/SDH Circuit Emulation Over Packet (CEP) encapsulation', Internet Draft <draft- ietf-pwe3-sonet>. This MIB reports to the PW-MIB as in: Zelig, D., Nadeau, T. 'Pseudo Wire (PW) Management Information Base'. The PW-MIB contains structures and MIB associations generic to Pseudo-Wire Virtual Circuit (VC) emulation. VC-specific MIBs (such as this) contain config and stats for specific VC types.
Imported Objects
| IF-MIB | InterfaceIndexOrZero |
| PerfHist-TC-MIB | PerfCurrentCount PerfIntervalCount |
| PW-MIB | pwVcIndex pwVcOperStatus |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 Counter64 experimental Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | RowStatus StorageType TEXTUAL-CONVENTION TimeStamp TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.3 | IdentitypwVcCepMIB | This MIB contains managed object definitions for Circuit Emulation over Packet (CEP) as in: Malis, A., Johnson, T., Zelig, D., and Martini, L. 'SONET/SDH Circu… | ||
| 1.3.6.1.3.0 | NodepwVcCepNotifications | |||
| 1.3.6.1.3.1 | NodepwVcCepObjects | |||
| 1.3.6.1.3.1.1 | TablepwVcCepTable | not-accessible | current | This table contains the index to the entry SONET path table for this CEP VC, and the index to the CEP config table. |
| 1.3.6.1.3.1.1.1 | RowpwVcCepEntry | not-accessible | current | This MIB reports to the PW-MIB. This table is indexed by the same index that was created for the associated entry in the PW VC Table (in the PW-MIB). - The PwV… |
| 1.3.6.1.3.1.1.1.1 | ColumnpwVcCepType | read-write | current | Specifies the type of CEP VC. Currently only structured types are supported. Other CEP Types may be defined in the future. Currently supported CEP types are: 1… |
| 1.3.6.1.3.1.1.1.2 | ColumnpwVcCepSonetIfIndex | read-write | current | This is a unique index within the ifTable. It represents the interface index for the SONET path for SPE emulation (RFC2558 section 3.3), an interface index for… |
| 1.3.6.1.3.1.1.1.3 | ColumnpwVcCepSonetTimeSlot | read-write | current | In structured SPE CEP, this object indicates the starting time-slot for this SONET path within the SONET line Danenberg et al Expires April 2003 15 Internet Dr… |
| 1.3.6.1.3.1.1.1.4 | ColumnpwVcCepSonetConfigError | read-only | current | timeslotInUse is when another CEP VC (via SONET ifIndex) has already reserved a timeslot(s) that this CEP VC is attempting to reserved. timeslotMisuse is set, … |
| 1.3.6.1.3.1.1.1.5 | ColumnpwVcCepCfgIndex | read-write | current | Index to CEP configuration table below. It is likely that multiple CEP VCs will share 1 CEP Cfg table entry. |
| 1.3.6.1.3.1.1.1.6 | ColumnpwVcCepTimeElapsed | read-only | current | The number of seconds, including partial seconds, that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adju… |
| 1.3.6.1.3.1.1.1.7 | ColumnpwVcCepValidIntervals | read-only | current | The number of previous 15-minute intervals for which data was collected. An agent with CEP capability must be capable of supporting at least n intervals. The m… |
| 1.3.6.1.3.1.1.1.8 | ColumnpwVcCepCurrentIndications | read-only | current | Definitions: missingPkt - While playing out a sequence of packets, a packet(s) was determined to be missing based on a gap in the CEP sequence number. Note: If… |
| 1.3.6.1.3.1.1.1.9 | ColumnpwVcCepLatchedIndications | read-only | current | The state of CEP indicators when the CEP VC last declared an errored second (either as ES, SES or a second with errors inside a UAS) condition. At this time, o… |
| 1.3.6.1.3.1.1.1.10 | ColumnpwVcCepLastEsTimeStamp | read-only | current | The value of sysUpTime on the most recent occasion at which the CEP VC entered the ES or SES state. |
| 1.3.6.1.3.1.2 | ScalarpwVcCepCfgIndexNext | read-only | current | This object contains an appropriate value to be used for pwVcCepCfgIndex when creating entries in the pwVcCepCfgTable. The value 0 indicates that no unassigned… |
| 1.3.6.1.3.1.3 | TablepwVcCepCfgTable | not-accessible | current | This table contains a set of parameters that may be referenced by 1 or more CEP VCs by pwVcCepTable. |
| 1.3.6.1.3.1.3.1 | RowpwVcCepCfgEntry | not-accessible | current | These parameters define the characteristics of a CEP VC. They are grouped here to ease NMS burden. Danenberg et al Expires April 2003 19 Internet Draft PW CEP … |
| 1.3.6.1.3.1.3.1.1 | ColumnpwVcCepCfgTableIndex | not-accessible | current | Primary index to this table |
| 1.3.6.1.3.1.3.1.2 | ColumnpwVcCepConfigError | read-only | current | Various configurations errors. Illegal settings within the pwVcCepCfg or pwVcCepSonetExt tables. |
| 1.3.6.1.3.1.3.1.3 | ColumnpwVcCepSonetPayloadLength | read-create | current | The number of SONET bytes of the Path or VT carried as payload within one packet. For example, for STS-1 SPE circuits, value of 783 bytes indicates that each p… |
| 1.3.6.1.3.1.3.1.4 | ColumnpwVcCepCfgMinPktLength | read-create | current | This is the minimum CEP packet length in number of bytes (including CEP header and payload). It applies to CEP's bandwidth-savings packets. Currently DBA is th… |
| 1.3.6.1.3.1.3.1.5 | ColumnpwVcCepCfgPktReorder | read-only | current | If set True: as inbound packets are queued in the jitter buffer, out of order packets are re-ordeed. The maximum sequence number differential (i.e., the range … |
| 1.3.6.1.3.1.3.1.6 | ColumnpwVcCepCfgEnableDBA | read-create | current | Bits set here MUST enable the DBA (dynamic bandwidth allocation) feature for the specified condition. Setting 'ais' MUST cause CEP packet payload suppression w… |
| 1.3.6.1.3.1.3.1.7 | ColumnpwVcCepCfgRtpHdrSuppress | read-only | current | If set True: an RTP header is not pre-pended to the CEP packet. |
| 1.3.6.1.3.1.3.1.8 | ColumnpwVcCepCfgJtrBfrDepth | read-create | current | This setting configures the number of microseconds of expected packet delay variation for this CEP VC over the PSN. The actual jitter buffer MUST be at least t… |
| 1.3.6.1.3.1.3.1.9 | ColumnpwVcCepCfgConsecPktsInsync | read-create | current | Consecutive pkts with sequential sequence numbers required to exit the LOPS state. |
| 1.3.6.1.3.1.3.1.10 | ColumnpwVcCepCfgConsecMissingOutSync | read-create | current | Consecutive missing pkts required to enter the LOPS state. |
| 1.3.6.1.3.1.3.1.11 | ColumnpwVcCepCfgPktErrorPlayOutValue | read-create | current | This is the value played when inbound packets have over/underflowed the jitter buffer, or are missing for any reason. This byte pattern is sent (played) on the… |
| 1.3.6.1.3.1.3.1.12 | ColumnpwVcCepCfgMissingPktsToSes | read-create | current | Number of missing packets detected (consecutive or not) within a 1 second window to cause a Severely Errored Second (SES) to be counted. |
| 1.3.6.1.3.1.3.1.13 | ColumnpwVcCepCfgSesToUas | read-create | current | Number of consecutive SESs before declaring VC in UAS state (and at which point pwVcCepPerfUASs starts counting). The SesToUas default value is 10 seconds. NOT… |
| 1.3.6.1.3.1.3.1.14 | ColumnpwVcCepCfgSecsToExitUas | read-create | current | Number of consecutive nonSESs before declaring VC is NOT in UAS state (and at which point pwVcCepPerfUASs stops counting). |
| 1.3.6.1.3.1.3.1.15 | ColumnpwVcCepCfgStorageType | read-create | current | This variable indicates the storage type for this object. |
| 1.3.6.1.3.1.3.1.16 | ColumnpwVcCepCfgRowStatus | read-create | current | For creating, modifying, and deleting this row. |
| 1.3.6.1.3.1.4 | TablepwVcCepFracTable | not-accessible | current | This table contains a set of parameters for CEP circuits with pwVcCepType FRAC type. |
| 1.3.6.1.3.1.4.1 | RowpwVcCepFracEntry | not-accessible | current | An entry is created in this table by the agent for every entry in the pwVcCep table in which the pwVcCepType is fracSpe. |
| 1.3.6.1.3.1.4.1.1 | ColumnpwVcCepFracMode | read-write | current | Fractional mode for STS-1/VC-3 circuits: notApplicable - When this is not STS-1/VC-3 signal. dynamic - EBM carried within the CEP header. Unequipped VTs are re… |
| 1.3.6.1.3.1.4.1.2 | ColumnpwVcCepFracConfigError | read-only | current | vtgMapEbmConflict is set when the configured static EBM does not match the configured vtgMap for fractional STS-1/VC-3 circuits, or when the TUG2Map is in conf… |
| 1.3.6.1.3.1.4.1.3 | ColumnpwVcCepFracAsync | read-write | current | The Asynchronous payload carried within the STS-1/VC-3. This variable should be set when 'staticAsync' Fractional STS-1/VC-3 pwVcCepFracMode is selected, and h… |
| 1.3.6.1.3.1.4.1.4 | ColumnpwVcCepFracVtgMap | read-write | current | The VT/VC types of the seven VTG/TUG-2 within the STS-1/VC-3. This variable should be set when 'dynamic', 'static' Or 'staticWithEbm' Fractional STS-1/VC-3 pwV… |
| 1.3.6.1.3.1.4.1.5 | ColumnpwVcCepFracEbm | read-write | current | Static Equipped Bit Mask (EBM) for STS-1/VC-3 channel. This variable should be set when 'static' Or 'staticWithEbm' Fractional STS-1/VC-3 pwVcCepFracMode is se… |
| 1.3.6.1.3.1.4.1.6 | ColumnpwVcCepFracPeerEbm | read-only | current | Equipped Bit Mask (EBM) for STS-1/VC-3 channel received from peer within the CEP extension header. |
| 1.3.6.1.3.1.4.1.7 | ColumnpwVcCepFracSdhVc4Mode | read-write | current | Fractional mode for VC-4 circuits: notApllicable - When this is not VC-4 circuit. dynamic - EBM carried within the CEP header. Unequipped VCs are removed from … |
| 1.3.6.1.3.1.4.1.8 | ColumnpwVcCepFracSdhVc4Tu3Map1 | read-write | current | If the first TUG-3 within the VC-4 contains a TU-3, this variable must be set. |
| 1.3.6.1.3.1.4.1.9 | ColumnpwVcCepFracSdhVc4Tu3Map2 | read-write | current | If the second TUG-3 within the VC-4 contains a TU-3, this variable must be set. |
| 1.3.6.1.3.1.4.1.10 | ColumnpwVcCepFracSdhVc4Tu3Map3 | read-write | current | If the third TUG-3 within the VC-4 contains a TU-3, this variable must be set. |
| 1.3.6.1.3.1.4.1.11 | ColumnpwVcCepFracSdhVc4Tug2Map1 | read-write | current | The VC types of the seven TUG-2 within the first TUG-3 of the VC-4. |
| 1.3.6.1.3.1.4.1.12 | ColumnpwVcCepFracSdhVc4Tug2Map2 | read-write | current | The VC types of the seven TUG-2 within the second TUG-3 of the VC-4. |
| 1.3.6.1.3.1.4.1.13 | ColumnpwVcCepFracSdhVc4Tug2Map3 | read-write | current | The VC types of the seven TUG-2 within the third TUG-3 of the VC-4. |
| 1.3.6.1.3.1.4.1.14 | ColumnpwVcCepFracSdhVc4Ebm1 | read-write | current | Static Equipped Bit Mask (EBM) for first TUG-3 within the VC-4. This variable should be set when 'static' or 'staticWithEbm' Fractional VC-4 pwVcCepFracMode is… |
| 1.3.6.1.3.1.4.1.15 | ColumnpwVcCepFracSdhVc4Ebm2 | read-write | current | Static Equipped Bit Mask (EBM) for second TUG-3 within the VC-4. This variable should be set when 'static' or 'StaticWithEbm' Fractional VC-4 pwVcCepFracMode i… |
| 1.3.6.1.3.1.4.1.16 | ColumnpwVcCepFracSdhVc4Ebm3 | read-write | current | Static Equipped Bit Mask (EBM) for third TUG-3 within the VC-4. This variable should be set when 'Static' or 'staticWithEbm' Fractional VC-4 pwVcCepFracMode is… |
| 1.3.6.1.3.1.4.1.17 | ColumnpwVcCepFracSdhVc4PeerEbm1 | read-only | current | Equipped Bit Mask (EBM) for the first TUG-3 within the fractional VC-4 channel received from peer within the CEP extension header. |
| 1.3.6.1.3.1.4.1.18 | ColumnpwVcCepFracSdhVc4PeerEbm2 | read-only | current | Equipped Bit Mask (EBM) for the second TUG-3 within the fractional VC-4 channel received from peer Danenberg et al Expires April 2003 30 Internet Draft PW CEP … |
| 1.3.6.1.3.1.4.1.19 | ColumnpwVcCepFracSdhVc4PeerEbm3 | read-only | current | Equipped Bit Mask (EBM) for the third TUG-3 within the fractional VC-4 channel received from peer within the CEP extension header. |
| 1.3.6.1.3.1.5 | TablepwVcCepPerfCurrentTable | not-accessible | current | CEP bridges the SONET and packet worlds. In the packet world, counts typically start from the time of service creation - and don't stop. In the SONET world, co… |
| 1.3.6.1.3.1.5.1 | RowpwVcCepPerfCurrentEntry | not-accessible | current | An entry in this table is created by the agent for every pwVcCep entry. After 15 minutes, the contents of this table entry are copied to a new entry in the pwV… |
| 1.3.6.1.3.1.5.1.1 | ColumnpwVcCepPerfCurrentDbaInPacketsHC | read-only | current | Number of DBA packets received. |
| 1.3.6.1.3.1.5.1.2 | ColumnpwVcCepPerfCurrentDbaOutPacketsHC | read-only | current | Number of DBA packets sent. |
| 1.3.6.1.3.1.5.1.3 | ColumnpwVcCepPerfCurrentInNegPtrAdjust | read-only | current | Number of negative pointer adjustments sent on the SONET path based on CEP pointer adjustments received. |
| 1.3.6.1.3.1.5.1.4 | ColumnpwVcCepPerfCurrentInPosPtrAdjust | read-only | current | Number of postive pointer adjustments sent on the SONET path based on CEP pointer adjustments received. |
| 1.3.6.1.3.1.5.1.5 | ColumnpwVcCepPerfCurrentInPtrAdjustSecs | read-only | current | Number of seconds in which a pos or neg pointer adjustment was sent on the SONET path. |
| 1.3.6.1.3.1.5.1.6 | ColumnpwVcCepPerfCurrentOutNegPtrAdjust | read-only | current | Number of negative pointer adjustments seen on the SONET path and encoded onto sent CEP packets. |
| 1.3.6.1.3.1.5.1.7 | ColumnpwVcCepPerfCurrentOutPosPtrAdjust | read-only | current | Number of positive pointer adjustments seen on the SONET path and encoded onto sent CEP packets. |
| 1.3.6.1.3.1.5.1.8 | ColumnpwVcCepPerfCurrentOutPtrAdjustSecs | read-only | current | Number of seconds in which a pos or neg pointer adjustment was seen on the SONET path. |
| 1.3.6.1.3.1.5.1.9 | ColumnpwVcCepPerfCurrentAbsPtrAdjust | read-only | current | Absolute Pointer adjustments is relative adjustment drifts between inbound and outbound streams. It is calculated as absolute value of : ( InPosPtrAdjust - InN… |
| 1.3.6.1.3.1.5.1.10 | ColumnpwVcCepPerfCurrentMissingPkts | read-only | current | Number of missing packets (as detected via CEP header sequence number gaps). |
| 1.3.6.1.3.1.5.1.11 | ColumnpwVcCepPerfCurrentPktsOoseq | read-only | current | Number of packets detected out of sequence (via CEP header sequence numbers), but successfully re-ordered. Note: some implementations may not support this feat… |
| 1.3.6.1.3.1.5.1.12 | ColumnpwVcCepPerfCurrentPktsOoRngDropped | read-only | current | Number of packets detected out of range (via CEP header sequence numbers), and could not be re- ordered, or could not fit in the jitter buffer. |
| 1.3.6.1.3.1.5.1.13 | ColumnpwVcCepPerfCurrentJtrBfrUnderruns | read-only | current | Number of times a packet needed to be played out and the jitter buffer was empty. |
| 1.3.6.1.3.1.5.1.14 | ColumnpwVcCepPerfCurrentPktsBadLength | read-only | current | Number of normal (non-bandwidth-saving packets received) larger or smaller than pwVcCepCfgNormalPktLength. |
| 1.3.6.1.3.1.5.1.15 | ColumnpwVcCepPerfCurrentSummaryErrors | read-only | current | A summary of all the packet error types above (from missing packets to bad length packets). |
| 1.3.6.1.3.1.5.1.16 | ColumnpwVcCepPerfCurrentESs | read-only | current | The counter associated with the number of Errored Seconds encountered. |
| 1.3.6.1.3.1.5.1.17 | ColumnpwVcCepPerfCurrentSESs | read-only | current | The counter associated with the number of Severely Errored Seconds encountered. |
| 1.3.6.1.3.1.5.1.18 | ColumnpwVcCepPerfCurrentUASs | read-only | current | The counter associated with the number of Unavailable Seconds encountered. |
| 1.3.6.1.3.1.5.1.19 | ColumnpwVcCepPerfCurrentFC | read-only | current | CEP Failure Counts (FC-CEP). The number of CEP failure events. A failure event begins when the LOPS failure is declared, and ends when the failure is cleared. … |
| 1.3.6.1.3.1.6 | TablepwVcCepPerfIntervalTable | not-accessible | current | This table provides per CEP VC performance information much like the pwVcCepPerfCurrentTable above. However, these counts represent historical 15 minute interv… |
| 1.3.6.1.3.1.6.1 | RowpwVcCepPerfIntervalEntry | not-accessible | current | An entry in this table is created by the agent for every pwVcCepPerfCurrentEntry that is 15 minutes old. The contents of the Current entry are copied to the ne… |
| 1.3.6.1.3.1.6.1.1 | ColumnpwVcCepPerfIntervalNumber | not-accessible | current | A number (normally between 1 and 96 to cover a 24 hour period) which identifies the interval for which the set of statistics is available. The interval identif… |
| 1.3.6.1.3.1.6.1.2 | ColumnpwVcCepPerfIntervalValidData | read-only | current | This variable indicates if the data for this interval is valid. |
| 1.3.6.1.3.1.6.1.3 | ColumnpwVcCepPerfIntervalReset | read-create | current | Used in cases where the user knows that the errors within this interval should not be counted. Writing 'reset' sets all error counts to zero. |
| 1.3.6.1.3.1.6.1.4 | ColumnpwVcCepPerfIntervalTimeElapsed | read-only | current | The duration of a particular interval in seconds, Adjustments in the system's time-of-day clock, may cause the interval to be greater or less than, the normal … |
| 1.3.6.1.3.1.6.1.5 | ColumnpwVcCepPerfIntervalDbaInPacketsHC | read-only | current | Number of DBA packets received. |
| 1.3.6.1.3.1.6.1.6 | ColumnpwVcCepPerfIntervalDbaOutPacketsHC | read-only | current | Number of DBA packets sent. |
| 1.3.6.1.3.1.6.1.7 | ColumnpwVcCepPerfIntervalInNegPtrAdjust | read-only | current | Number of negative pointer adjustments sent on the SONET path based on CEP pointer adjustments received. |
| 1.3.6.1.3.1.6.1.8 | ColumnpwVcCepPerfIntervalInPosPtrAdjust | read-only | current | Number of postive pointer adjustments sent on the SONET path based on CEP pointer adjustments received. |
| 1.3.6.1.3.1.6.1.9 | ColumnpwVcCepPerfIntervalInPtrAdjustSecs | read-only | current | Number of seconds in which a pos or neg pointer adjustment was sent on the SONET path. |
| 1.3.6.1.3.1.6.1.10 | ColumnpwVcCepPerfIntervalOutNegPtrAdjust | read-only | current | Number of negative pointer adjustments seen on the SONET path and encoded onto sent CEP packets. |
| 1.3.6.1.3.1.6.1.11 | ColumnpwVcCepPerfIntervalOutPosPtrAdjust | read-only | current | Number of positive pointer adjustments seen on the SONET path and encoded onto sent CEP packets. |
| 1.3.6.1.3.1.6.1.12 | ColumnpwVcCepPerfIntervalOutPtrAdjustSecs | read-only | current | Number of seconds in which a pos or neg pointer adjustment was seen on the SONET path. |
| 1.3.6.1.3.1.6.1.13 | ColumnpwVcCepPerfIntervalAbsPtrAdjust | read-only | current | Absolute Pointer adjustments is relative adjustment drifts between inbound and outbound streams. It is calculated as absolute value of : ( InPosPtrAdjust - InN… |
| 1.3.6.1.3.1.6.1.14 | ColumnpwVcCepPerfIntervalMissingPkts | read-only | current | Number of missing packets (as detected via CEP header sequence number gaps). |
| 1.3.6.1.3.1.6.1.15 | ColumnpwVcCepPerfIntervalPktsOoseq | read-only | current | Number of packets detected out of sequence (via CEP header sequence numbers), but succesfully re-ordered. Note: some implementations mat not support this featu… |
| 1.3.6.1.3.1.6.1.16 | ColumnpwVcCepPerfIntervalPktsOoRngDropped | read-only | current | Number of packets detected out of range (via CEP header sequence numbers), and could not be re- ordered, or could not fit in the jitter buffer. |
| 1.3.6.1.3.1.6.1.17 | ColumnpwVcCepPerfIntervalJtrBfrUnderruns | read-only | current | Number of times a packet needed to be played out and the jitter buffer was empty. |
| 1.3.6.1.3.1.6.1.18 | ColumnpwVcCepPerfIntervalPktsBadLength | read-only | current | Number of packets received larger or smaller than pwVcCepCfgNormalPktLength. |
| 1.3.6.1.3.1.6.1.19 | ColumnpwVcCepPerfIntervalSummaryErrors | read-only | current | A summary of all the packet error types above (from missing packets to bad length packets). |
| 1.3.6.1.3.1.6.1.20 | ColumnpwVcCepPerfIntervalESs | read-only | current | The counter associated with the number of Errored Seconds encountered. |
| 1.3.6.1.3.1.6.1.21 | ColumnpwVcCepPerfIntervalSESs | read-only | current | The counter associated with the number of Severely Errored Seconds encountered. |
| 1.3.6.1.3.1.6.1.22 | ColumnpwVcCepPerfIntervalUASs | read-only | current | The counter associated with the number of Unavailable Seconds encountered. |
| 1.3.6.1.3.1.6.1.23 | ColumnpwVcCepPerfIntervalFC | read-only | current | CEP Failure Counts (FC-CEP). The number of CEP failure events. A failure event begins when the LOPS failure is declared, and ends when the failure is cleared. … |
| 1.3.6.1.3.1.7 | TablepwVcCepPerfTotalTable | not-accessible | current | This table provides per CEP VC performance information much like the pwVcCepPerfIntervalTable above. However, these counts represent complete historical inform… |
| 1.3.6.1.3.1.7.1 | RowpwVcCepPerfTotalEntry | not-accessible | current | An entry is created in this table by the agent for every entry in the pwVcCep table. |
| 1.3.6.1.3.1.7.1.1 | ColumnpwVcCepPerfTotalDbaInPacketsHC | read-only | current | Number of DBA packets received. |
| 1.3.6.1.3.1.7.1.2 | ColumnpwVcCepPerfTotalDbaOutPacketsHC | read-only | current | Number of DBA packets sent. |
| 1.3.6.1.3.1.7.1.3 | ColumnpwVcCepPerfTotalInNegPtrAdjust | read-only | current | Number of negative pointer adjustments sent on the SONET path based on CEP pointer adjustments received. |
| 1.3.6.1.3.1.7.1.4 | ColumnpwVcCepPerfTotalInPosPtrAdjust | read-only | current | |
| 1.3.6.1.3.1.7.1.5 | ColumnpwVcCepPerfTotalInPtrAdjustSecs | read-only | current | Number of seconds in which a pos or neg pointer adjustment was sent on the SONET path. |
| 1.3.6.1.3.1.7.1.6 | ColumnpwVcCepPerfTotalOutNegPtrAdjust | read-only | current | Number of negative pointer adjustments seen on the SONET path and encoded onto sent CEP packets. |
| 1.3.6.1.3.1.7.1.7 | ColumnpwVcCepPerfTotalOutPosPtrAdjust | read-only | current | Number of positive pointer adjustments seen on the SONET path and encoded onto sent CEP packets. |
| 1.3.6.1.3.1.7.1.8 | ColumnpwVcCepPerfTotalOutPtrAdjustSecs | read-only | current | Number of seconds in which a pos or neg pointer adjustment was seen on the SONET path. |
| 1.3.6.1.3.1.7.1.9 | ColumnpwVcCepPerfTotalAbsPtrAdjust | read-only | current | Absolute Pointer adjustments is relative adjustment drifts between inbound and outbound streams. It is calculated as absolute value of : ( InPosPtrAdjust - InN… |
| 1.3.6.1.3.1.7.1.10 | ColumnpwVcCepPerfTotalMissingPkts | read-only | current | Number of missing packets (as detected via CEP header sequence number gaps). |
| 1.3.6.1.3.1.7.1.11 | ColumnpwVcCepPerfTotalPktsOoseq | read-only | current | Number of packets detected out of sequence (via CEP header sequence numbers), but successfully re-ordered. Note: some implementations may not support this feat… |
| 1.3.6.1.3.1.7.1.12 | ColumnpwVcCepPerfTotalPktsOoRngDropped | read-only | current | Number of packets detected out of range (via CEP header sequence numbers), and could not be re- ordered, or could not fit in the jitter buffer. |
| 1.3.6.1.3.1.7.1.13 | ColumnpwVcCepPerfTotalJtrBfrUnderruns | read-only | current | Number of times a packet needed to be played out and the jitter buffer was empty. |
| 1.3.6.1.3.1.7.1.14 | ColumnpwVcCepPerfTotalPktsBadLength | read-only | current | Number of packets received larger or smaller than pwVcCepCfgNormalPktLength. |
| 1.3.6.1.3.1.7.1.15 | ColumnpwVcCepPerfTotalSummaryErrors | read-only | current | A summary of all the packet error types above (from missing packets to bad length packets). |
| 1.3.6.1.3.1.7.1.16 | ColumnpwVcCepPerfTotalESs | read-only | current | The counter associated with the number of Errored Seconds encountered. See draft-ietf-pwe3-sonet for definition of ES. |
| 1.3.6.1.3.1.7.1.17 | ColumnpwVcCepPerfTotalSESs | read-only | current | The counter associated with the number of Severely Errored Seconds. See pwVcCepCfgMissingPktsToSes. Also see draft-ietf-pwe3-sonet for definition. |
| 1.3.6.1.3.1.7.1.18 | ColumnpwVcCepPerfTotalUASs | read-only | current | The counter associated with the number of UnAvailable Seconds. See pwVcCepCfgSesToUAS. NOTE: When first entering the UAS state, the number of SesToUas is added… |
| 1.3.6.1.3.1.7.1.19 | ColumnpwVcCepPerfTotalFC | read-only | current | CEP Failure Counts (FC-CEP). The number of CEP failure events. A failure event begins when the LOPS failure is declared, and ends when the failure is cleared. |
| 1.3.6.1.3.1.7.1.20 | ColumnpwVcCepPerfTotalDiscontinuityTime | read-only | current | The value of sysUpTime on the most recent occasion at which any one or more of this segment's Counter32 or Counter64 suffered a discontinuity. If no such disco… |
| 1.3.6.1.3.1.8 | ScalarpwVcCepGlobalNotifyEnable | read-write | current | If this object is true, then it enables the generation of pwVcCepUp and pwVcCepDown notifications, otherwise these notifications are not emitted. Note: enablin… |
| 1.3.6.1.3.1.9 | TablepwVcCepConformanceCfgTable | not-accessible | current | This table provides the means for the agent to declare whether certain CEP VC statistics objects are supported (conformed to) or not. If not supported, then th… |
| 1.3.6.1.3.1.9.1 | RowpwVcCepConformanceCfgEntry | not-accessible | current | The agent MUST create a single entry in this table. |
| 1.3.6.1.3.1.9.1.1 | ColumnpwVcCepConformanceCfgIndex | not-accessible | current | Any arbitrary number |
| 1.3.6.1.3.1.9.1.2 | ColumnpwVcCepPerfDbaInPacketsHCTruth | read-only | current | Tells whether the pwVcCepPerf...DbaInPacketsHC in the pwVcCepPerf...Table is supported. |
| 1.3.6.1.3.1.9.1.3 | ColumnpwVcCepPerfDbaInPacketsHCDesc | read-only | current | Explanation for pwVcCepPerf...DbaInPacketsHC support in the pwVcCepPerf...Table. |
| 1.3.6.1.3.1.9.1.4 | ColumnpwVcCepPerfDbaOutPacketsHCTruth | read-only | current | Tells whether the pwVcCepPerf...DbaOutPacketsHC in the pwVcCepPerf...Table is supported. |
| 1.3.6.1.3.1.9.1.5 | ColumnpwVcCepPerfDbaOutPacketsHCDesc | read-only | current | Explanation for pwVcCepPerf...DbaOutPacketsHC support in the pwVcCepPerf...Table. |
| 1.3.6.1.3.1.9.1.6 | ColumnpwVcCepPerfPktsOoseqTruth | read-only | current | Tells whether the pwVcCepPerf...PktsOoseq in the pwVcCepPerf...Table is supported. |
| 1.3.6.1.3.1.9.1.7 | ColumnpwVcCepPerfPktsOoseqDesc | read-only | current | Explanation for pwVcCepPerf...PktsOoseq support in the pwVcCepPerf...Table. |
| 1.3.6.1.3.1.9.1.8 | ColumnpwVcCepPerfPktsOoRngDroppedTruth | read-only | current | Tells whether the pwVcCepPerf...PktsOoRngDropped in the pwVcCepPerf...Table is supported. |
| 1.3.6.1.3.1.9.1.9 | ColumnpwVcCepPerfPktsOoRngDroppedDesc | read-only | current | Explanation for pwVcCepPerf...PktsOoRngDropped support in the pwVcCepPerf...Table. |
| 1.3.6.1.3.1.9.1.10 | ColumnpwVcCepPerfSummaryErrorsTruth | read-only | current | Tells whether the pwVcCepPerf...SummaryError in the pwVcCepPerf...Table is supported. |
| 1.3.6.1.3.1.9.1.11 | ColumnpwVcCepPerfSummaryErrorsDesc | read-only | current | Explanation for pwVcCepPerf...SummaryError support in the pwVcCepPerf...Table. |
| 1.3.6.1.3.2 | NodepwVcCepConformance | |||
| 1.3.6.1.3.2.1 | NodepwVcCepGroups | |||
| 1.3.6.1.3.2.1.1 | GrouppwVcCepGroup | current | Collection of objects for basic CEP VC config and status. | |
| 1.3.6.1.3.2.1.2 | GrouppwVcCepCfgGroup | current | Collection of detailed objects needed to configure CEP VCs. | |
| 1.3.6.1.3.2.1.3 | GrouppwVcCepPerfCurrentGroup | current | Collection of statistics objects for CEP VCs. | |
| 1.3.6.1.3.2.1.4 | GrouppwVcCepPerfIntervalGroup | current | Collection of statistics objects for CEP VCs. | |
| 1.3.6.1.3.2.1.5 | GrouppwVcCepPerfTotalGroup | current | Collection of statistics objects for CEP VCs. | |
| 1.3.6.1.3.2.1.7 | GrouppwVcCepEventGroup | current | Collection of event objects for CEP VCs. | |
| 1.3.6.1.3.2.1.8 | GrouppwVcCepFracGroup | current | Collection of fractional SPE groups. These objects are optional and should be supported only if fractional SPE is supported within the network element. | |
| 1.3.6.1.3.2.1.9 | GrouppwVcCepConformanceCfgGroup | current | Collection of objects declaring conformance to other objects. | |
| 1.3.6.1.3.2.2 | NodepwVcCepCompliances | |||
| 1.3.6.1.3.2.2.1 | CompliancepwCepModuleCompliance | current | The compliance statement for agent that support PW over CEP PSN operation. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| PwVcCepCfgIndex | Unsigned32 Danenberg et al Expires April 2003 12 Internet Draft PW CEP MIB October 2002 | current | Index into the pwVcCepCfgTable. |
| PwVcCepFracAsyncMap | INTEGER { other ( 0), ds3 ( 1), e3 ( 2) } | current | The type of Asynchronous mapping carried inside STS-1, VC-3 or TUG-3 containing TU-3 circuit. The value of 'other' MUST be used if the Use of this object is not applicable. |
| PwVcCepSdhVc4Ebm | Unsigned32 | current | Equipped Bit Mask (EBM) as defined in draft-ietf-pwe3- sonet-vt used for each TUG-3 in fractional VC-4 circuits. The EBM bits are the 30 least significant bits out of the 32 bit value |
| PwVcCepSonetEbm | Unsigned32 | current | Equipped Bit Mask (EBM) as defined in draft-ietf-pwe3- sonet-vt used for fractional STS-1/VC-3. The EBM bits are the 28 least significant bits out of the 32 bit value |
| PwVcCepSonetVtgMap | Unsigned32 | current | The VT/VC types carried in the 7 VTG/TUG-2s. The format is 28 bits in the form of an Equipped Bit Mask (EBM) as defined in draft-ietf-pwe3-sonet-vt used for fractional STS-1/VC-3. The EBM specifies the maximal occupanci… |