RUGGEDCOM-SERIAL-MIB
147 objects
RuggedCom MIB for Managing Proprietary Settings for Serial Ports and Serial Protocols on RuggedCom Serial Server Devices.
Imported Objects
| IF-MIB | InterfaceIndex |
| Q-BRIDGE-MIB | PortList |
| RUGGEDCOM-MIB | ruggedcomMgmt |
| SNMPv2-CONF | OBJECT-GROUP |
| SNMPv2-SMI | Integer32 IpAddress MODULE-IDENTITY OBJECT-IDENTITY OBJECT-TYPE |
| SNMPv2-TC | TEXTUAL-CONVENTION |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.15004.4.6 | IdentityrcSerial | RuggedCom MIB for Managing Proprietary Settings for Serial Ports and Serial Protocols on RuggedCom Serial Server Devices. | ||
| 1.3.6.1.4.1.15004.4.6.1 | IdentityrcSerialPortParams | current | The main subtree for managing Global Serial Port parameters. | |
| 1.3.6.1.4.1.15004.4.6.1.1 | TablercSerialPortTable | not-accessible | current | A list of port entries. The number of entries might be retreived as the value of object 'rs232Number' from RFC1659. |
| 1.3.6.1.4.1.15004.4.6.1.1.1 | RowrcSerialPortEntry | not-accessible | current | Status and configuration parameters for a port. |
| 1.3.6.1.4.1.15004.4.6.1.1.1.1 | ColumnrcSerialPortNumber | not-accessible | current | The physical Serial Port Number of the device for which this Entry contains configuration settings. |
| 1.3.6.1.4.1.15004.4.6.1.1.1.2 | ColumnrcSerialPortIfIndex | read-only | current | The value of ifIndex for the port. This value is same as 'rs232PortIndex' which is the index used for 'rs232PortTable' in RS-232-MIB. |
| 1.3.6.1.4.1.15004.4.6.1.1.1.3 | ColumnrcSerialProtocol | read-write | current | A Serial Protocol supported on the Serial Port represented by this entry. |
| 1.3.6.1.4.1.15004.4.6.1.1.1.4 | ColumnrcSerialPortType | read-write | current | A Serial Port Type supported on the Serial Port represented by this entry. |
| 1.3.6.1.4.1.15004.4.6.1.1.1.5 | ColumnrcSerialForceHD | read-write | current | Enables forcing half duplex mode of operation on the Serial Port. While sending data out of the serial port all received data are ignored. This mode of operati… |
| 1.3.6.1.4.1.15004.4.6.1.1.1.6 | ColumnrcSerialTurnAround | read-write | current | The amount of delay between the transmission of individual messages out of the serial port. For 'rcSerialProtocol' object value modbusServer(3) this value must… |
| 1.3.6.1.4.1.15004.4.6.1.1.1.7 | ColumnrcSerialPostTxDelay | read-write | current | The number of bits needed to generate required delay with configured baudrate('rs232PortOutSpeed') after the last bit of the packet was sent out before serial … |
| 1.3.6.1.4.1.15004.4.6.1.1.1.8 | ColumnrcSerialHoldTime | read-write | current | The maximum amount of time in ms that serial packet can be held in the queue before being sent to the serial line. Time is measured from the moment the packet … |
| 1.3.6.1.4.1.15004.4.6.1.1.1.9 | ColumnrcSerialDscp | read-write | current | The value of DS byte to be set in the IP header. DS byte setting is supported in the egress direction only. |
| 1.3.6.1.4.1.15004.4.6.1.1.1.10 | ColumnrcSerialRxtoTxDelay | read-write | current | The minimum amount of time in ms that the transmission of a new message should delay after the last message is received through the serial port. This parameter… |
| 1.3.6.1.4.1.15004.4.6.2 | IdentityrcMbServer | current | The main subtree for managing the Modbus Protocol Server settings on RuggedCom serial Devices. | |
| 1.3.6.1.4.1.15004.4.6.2.1 | TablercMbServerTable | not-accessible | current | This table provides configuration options for the ports when 'rcSerialProtocol'equals modbusServer(3). |
| 1.3.6.1.4.1.15004.4.6.2.1.1 | RowrcMbServerEntry | not-accessible | current | List of all the configuration options for a port for which 'rcSerialProtocol' equals modbusServer(3). |
| 1.3.6.1.4.1.15004.4.6.2.1.1.1 | ColumnrcMbServerPort | not-accessible | current | The physical Serial Port Number for which this Entry contains the Modbus Server Protocol configuration settings. |
| 1.3.6.1.4.1.15004.4.6.2.1.1.2 | ColumnrcMbServerRespTimer | read-write | current | The allowable time to wait for the RTU to start to respond. |
| 1.3.6.1.4.1.15004.4.6.2.1.1.3 | ColumnrcMbServerAuxTcpPort | read-write | current | The alternative TCP port number where a 'rcMbServerPort' may listen to incoming TCP conncetions. Note:TCP Modbus Server always listens on TCP port 502. So this… |
| 1.3.6.1.4.1.15004.4.6.2.1.1.4 | ColumnrcMbServerSendExcep | read-write | current | Allows the RuggedCom Serial Devices to enable or disable sending TCP Modbus exception back to the master if response has not been received from the RTU within … |
| 1.3.6.1.4.1.15004.4.6.2.1.1.5 | ColumnrcMbServerLinkStats | read-write | current | Enables links statistics collection. |
| 1.3.6.1.4.1.15004.4.6.3 | IdentityrcMbClient | current | The main subtree for managing the Modbus Protocol Client Settings on RuggedCom serial devices. | |
| 1.3.6.1.4.1.15004.4.6.3.1 | ScalarrcMbClientIPPort | read-write | current | A remote port number to which protocol connection manager sends TCP connection requests. |
| 1.3.6.1.4.1.15004.4.6.3.2 | ScalarrcMbClientFwdExcp | read-write | current | Enables forwarding exception messages to the Master as exception codes 10 (no path) or 11 (no response). When the Master polls for an unconfigured RTU or the r… |
| 1.3.6.1.4.1.15004.4.6.3.3 | ScalarrcMbClientLinkStats | read-write | current | Enables link statistics collection. |
| 1.3.6.1.4.1.15004.4.6.3.4 | ScalarrcMbClientDscp | read-write | current | The value of DS byte to be set in the IP header. DS byte setting is supported in the egress direction only. |
| 1.3.6.1.4.1.15004.4.6.4 | IdentityrcRawSock | current | The main subtree for managing the Raw Socket Protocol Settings on RuggedCom serial devices. | |
| 1.3.6.1.4.1.15004.4.6.4.1 | TablercRawSockTable | not-accessible | current | This table represents the entries for ports configured for Raw Socket serial protocol on RuggedCom serial devices. |
| 1.3.6.1.4.1.15004.4.6.4.1.1 | RowrcRawSockEntry | not-accessible | current | List of all the configuration options available for a port configured for Raw Socket serial protocol on Ruggedcom serial devices. |
| 1.3.6.1.4.1.15004.4.6.4.1.1.1 | ColumnrcRawSockPort | not-accessible | current | The physical Serial Port Number for which this Entry contains the Raw Socket serial protocol configuration settings. |
| 1.3.6.1.4.1.15004.4.6.4.1.1.2 | ColumnrcRawSockPackChar | read-write | current | The character that can be used to force forwarding of accumulated data to the network. If a packetization character is not configured - object is set to the va… |
| 1.3.6.1.4.1.15004.4.6.4.1.1.3 | ColumnrcRawSockPackTimer | read-write | current | The delay in ms from the last received character until when data is forwarded. |
| 1.3.6.1.4.1.15004.4.6.4.1.1.4 | ColumnrcRawSockPackSize | read-write | current | The maximum number of bytes received from serial port to be forwarded. |
| 1.3.6.1.4.1.15004.4.6.4.1.1.5 | ColumnrcRawSockFlowControl | read-write | current | The type of FlowControl to be used on the port. |
| 1.3.6.1.4.1.15004.4.6.4.1.1.6 | ColumnrcRawSockTransport | read-write | current | A transport protocol used for IP traffic for protocol on this port. |
| 1.3.6.1.4.1.15004.4.6.4.1.1.7 | ColumnrcRawSockCallDir | read-write | current | Defines following: - whether to accept an incoming connection 'in(0)' or - to place an outgoing connection 'out(1)' or - to place an outgoing connection and wa… |
| 1.3.6.1.4.1.15004.4.6.4.1.1.8 | ColumnrcRawSockMaxConn | read-write | current | The maximum number of allowed incoming TCP connections. |
| 1.3.6.1.4.1.15004.4.6.4.1.1.9 | ColumnrcRawSockLocPort | read-write | current | The local IP port to listen to an incoming TCP connection or UDP datagrams. |
| 1.3.6.1.4.1.15004.4.6.4.1.1.10 | ColumnrcRawSockRemPort | read-write | current | The remote IP port to use when placing an outgoing connection. |
| 1.3.6.1.4.1.15004.4.6.4.1.1.11 | ColumnrcRawSockIpAdd | read-write | current | Defines the IpAddress based on the following: - For outgoing TCP connection (client) 'rcRawSockCallDir' is 'out(2)' this is the remote IP address to communicat… |
| 1.3.6.1.4.1.15004.4.6.4.1.1.12 | ColumnrcRawSockLinkStats | read-write | current | Enables links statistics collection for RawSocket on this port. |
| 1.3.6.1.4.1.15004.4.6.5 | IdentityrcPreemptRS | current | The main subtree for managing the Preemptive Raw Socket Protocol settings on RuggedCom serial devices. | |
| 1.3.6.1.4.1.15004.4.6.5.1 | TablercPreemptRSTable | not-accessible | current | This Table defines the configuration options available for ports configured for PreEmptive Raw Socket serial protocol. |
| 1.3.6.1.4.1.15004.4.6.5.1.1 | RowrcPreemptRSEntry | not-accessible | current | A list of port entries with configuration options for ports configured for PreEmptive Raw Socket protocol. |
| 1.3.6.1.4.1.15004.4.6.5.1.1.1 | ColumnrcPreemptRSPort | not-accessible | current | The physical Serial Port Number for which this Entry contains the Preemptive Raw Socket serial protocol configuration settings. |
| 1.3.6.1.4.1.15004.4.6.5.1.1.2 | ColumnrcPreemptRSPackChar | read-write | current | The character that can be used to force forwarding of accumulated data to the network. If a packetization character is not configured - object is set to the va… |
| 1.3.6.1.4.1.15004.4.6.5.1.1.3 | ColumnrcPreemptRSPackTimer | read-write | current | The delay in milliseconds from the last received character until when data is forwarded. |
| 1.3.6.1.4.1.15004.4.6.5.1.1.4 | ColumnrcPreemptRSPackSize | read-write | current | The Maximum number of bytes received from serial port to be packed in one IP packet. |
| 1.3.6.1.4.1.15004.4.6.5.1.1.5 | ColumnrcPreemptRSFlowControl | read-write | current | The type of FlowControl to be used on the port. |
| 1.3.6.1.4.1.15004.4.6.5.1.1.6 | ColumnrcPreemptRSLocPort | read-write | current | The local IP port to listen to an incoming TCP connection or UDP datagrams. |
| 1.3.6.1.4.1.15004.4.6.5.1.1.7 | ColumnrcPreemptRSRemPort | read-write | current | The remote TCP port to use when placing an outgoing connection. |
| 1.3.6.1.4.1.15004.4.6.5.1.1.8 | ColumnrcPreemptRSIpAdd | read-write | current | Defines the IpAddress based on the following: - For outgoing TCP connection (client) 'rcRawSockCallDir' is 'out(2)' this is the remote IP address to communicat… |
| 1.3.6.1.4.1.15004.4.6.5.1.1.9 | ColumnrcPreemptRSLinkStats | read-write | current | Enables links statistics collection. |
| 1.3.6.1.4.1.15004.4.6.5.1.1.10 | ColumnrcPreemptRSDynPackChar | read-write | current | The character that can be used to force forwarding of accumulated data to the network for connection to dynamic master. If a packetization character is not con… |
| 1.3.6.1.4.1.15004.4.6.5.1.1.11 | ColumnrcPreemptRSDynPackTimer | read-write | current | The delay in milliseconds from the last received character until when data is forwarded to the dynamic master. |
| 1.3.6.1.4.1.15004.4.6.5.1.1.12 | ColumnrcPreemptRSDynTimeout | read-write | current | The time in seconds that is allowed to dynamic master to be idle before it's connection is closed. The protocol listens to the socket open to dymamic master, a… |
| 1.3.6.1.4.1.15004.4.6.6 | IdentityrcTinAndWin | current | The main subtree for managing the TIN and WIN protocol settings on RuggedCom serial devices. | |
| 1.3.6.1.4.1.15004.4.6.6.1 | ScalarrcTinAndWinTinMode | read-write | current | The TIN Protocol running mode |
| 1.3.6.1.4.1.15004.4.6.6.2 | ScalarrcTinAndWinTinTrans | read-write | current | A transport protocol used for IP traffic for TIN protocol. |
| 1.3.6.1.4.1.15004.4.6.6.3 | ScalarrcTinAndWinWinTrans | read-write | current | A transport protocol used for IP traffic for WIN protocol. |
| 1.3.6.1.4.1.15004.4.6.6.4 | ScalarrcTinAndWinTinIpPort | read-write | current | A local port number on which TIN protocol listens to connections or UDP datagrams. |
| 1.3.6.1.4.1.15004.4.6.6.5 | ScalarrcTinAndWinWinIpPort | read-write | current | A local port number on which WIN protocol listens to connections or UDP datagrams. |
| 1.3.6.1.4.1.15004.4.6.6.6 | ScalarrcTinAndWinMsgAgingTime | read-write | current | Aging time for TIN mode2 messages. The feature is disabled if the value of this object is '0'. When the feature is enabled, any TIN mode2 message received will… |
| 1.3.6.1.4.1.15004.4.6.6.7 | ScalarrcTinAndWinAddrAgingTime | read-write | current | The time of communication inactivity in milliseconds after which a learned TIN address is removed from the dynamic device address table. Entries in Link Statis… |
| 1.3.6.1.4.1.15004.4.6.6.8 | ScalarrcTinAndWinBroadCastAddr | read-write | current | The device address table in which addresses will be found for broadcast messages. |
| 1.3.6.1.4.1.15004.4.6.6.9 | ScalarrcTinAndWinUniAddr | read-write | current | The device address table in which addresses will be found for unicast messages. |
| 1.3.6.1.4.1.15004.4.6.6.10 | ScalarrcTinAndWinLinkStats | read-write | current | Enables links statistics collection for TIN and WIN protocols. |
| 1.3.6.1.4.1.15004.4.6.6.11 | ScalarrcTinAndWinWinDscp | read-write | current | The value of DS byte to be set in the IP header. DS byte setting is supported in the egress direction only. |
| 1.3.6.1.4.1.15004.4.6.6.12 | ScalarrcTinAndWinTinDscp | read-write | current | The value of DS byte to be set in the IP header. DS byte setting is supported in the egress direction only. |
| 1.3.6.1.4.1.15004.4.6.7 | IdentityrcMicrolok | current | The main subtree for managing the Microlok protocol settings on RuggedCom serial devices. | |
| 1.3.6.1.4.1.15004.4.6.7.1 | ScalarrcMicrolokTransport | read-write | current | A transport protocol used for IP traffic for Microloc protocol. |
| 1.3.6.1.4.1.15004.4.6.7.2 | ScalarrcMicrolokIpPort | read-write | current | A local port number on which Microloc protocol listens to connections or UDP datagrams. |
| 1.3.6.1.4.1.15004.4.6.7.3 | ScalarrcMicrolokLinkStats | read-write | current | Enables links statistics collection. |
| 1.3.6.1.4.1.15004.4.6.7.4 | ScalarrcMicrolokDscp | read-write | current | The value of DS byte to be set in the IP header. DS byte setting is supported in the egress direction only. |
| 1.3.6.1.4.1.15004.4.6.8 | IdentityrcDnp | current | Tha main subtree for managing the Dnp protocol settings on RuggedCom serial devices. | |
| 1.3.6.1.4.1.15004.4.6.8.1 | ScalarrcDnpTransport | read-write | current | A transport protocol used for IP traffic for DNP protocol. |
| 1.3.6.1.4.1.15004.4.6.8.2 | ScalarrcDnpIpPort | read-write | current | A local port number on which DNP protocol listens to connections or UDP datagrams. |
| 1.3.6.1.4.1.15004.4.6.8.3 | ScalarrcDnpLearning | read-write | current | Enable or disable address learning. Learning can be disabled, or enabled on management IP interface, or enabled on the interface with specific IP address. If l… |
| 1.3.6.1.4.1.15004.4.6.8.4 | ScalarrcDnpAgingTimer | read-write | current | The time of communication inactivity after which a learned DNP address is removed from the device address table. Entries in Link Statistics Table with the aged… |
| 1.3.6.1.4.1.15004.4.6.8.5 | ScalarrcDnpLinkStats | read-write | current | Enables links statistics collection. |
| 1.3.6.1.4.1.15004.4.6.8.6 | ScalarrcDnpDscp | read-write | current | The value of DS byte to be set in the IP header. DS byte setting is supported in the egress direction only. |
| 1.3.6.1.4.1.15004.4.6.9 | IdentityrcDnpRs | current | Tha main subtree for managing the Dnp over Raw Socket protocol settings on RuggedCom serial devices. | |
| 1.3.6.1.4.1.15004.4.6.9.1 | TablercDnpRsTable | not-accessible | current | This table represents the set of parameters provide the ability to configure DNP over RawSocket protocol settings for serial ports. If no ports appear, then th… |
| 1.3.6.1.4.1.15004.4.6.9.1.1 | RowrcDnpRsEntry | not-accessible | current | List of ports with configuration parameters for DNP over RawSocket serial protocol . |
| 1.3.6.1.4.1.15004.4.6.9.1.1.1 | ColumnrcDnpRsPort | not-accessible | current | The physical Serial Port Number for which this Entry contains DNP over Raw Socket serial protocol configuration settings. |
| 1.3.6.1.4.1.15004.4.6.9.1.1.2 | ColumnrcDnpRsCalllDir | read-write | current | Defines following: - whether to accept an incoming connection 'in(0)' or - to place an outgoing connection 'out(1)' or - to place an outgoing connection and wa… |
| 1.3.6.1.4.1.15004.4.6.9.1.1.3 | ColumnrcDnpRsTransport | read-write | current | A transport protocol used for IP traffic for DNPRS on this port. |
| 1.3.6.1.4.1.15004.4.6.9.1.1.4 | ColumnrcDnpRsMaxConns | read-write | current | The maximum number of allowed incoming TCP connections. |
| 1.3.6.1.4.1.15004.4.6.9.1.1.5 | ColumnrcDnpRsLocPort | read-write | current | The local IP port to listen to an incoming TCP connection or UDP datagrams. |
| 1.3.6.1.4.1.15004.4.6.9.1.1.6 | ColumnrcDnpRsRemPort | read-write | current | The remote TCP port to use when placing an outgoing connection. |
| 1.3.6.1.4.1.15004.4.6.9.1.1.7 | ColumnrcDnpRsIpAdd | read-write | current | Defines the IpAddress based on the following: - For outgoing TCP connection (client) 'rcRawSockCallDir' is 'out(2)' this is the remote IP address to communicat… |
| 1.3.6.1.4.1.15004.4.6.9.1.1.8 | ColumnrcDnpRsLinkStats | read-write | current | Enables links statistics collection. |
| 1.3.6.1.4.1.15004.4.6.10 | IdentityrcMirrorBits | current | Tha main subtree for managing the Mirrored Bit protocol settings on RuggedCom serial devices. | |
| 1.3.6.1.4.1.15004.4.6.10.1 | TablercMirrBitsTable | not-accessible | current | This table presents the list of ports with configuration options for configuring the Mirrirod Bits serial protocol on RuggedCom serial devices |
| 1.3.6.1.4.1.15004.4.6.10.1.1 | RowrcMirrBitsEntry | not-accessible | current | List of configuration options for all the ports configured for Mirrored Bits serial protocol. |
| 1.3.6.1.4.1.15004.4.6.10.1.1.1 | ColumnrcMirrBitsPort | not-accessible | current | The physical Serial Port Number for which this Entry contains the Mirrored Bits serial protocol configuration settings. |
| 1.3.6.1.4.1.15004.4.6.10.1.1.2 | ColumnrcMirrBitsTransport | read-write | current | A transport protocol used for IP traffic for MorroredBits on this port. This object is always set to the value of 'udp(2)'. |
| 1.3.6.1.4.1.15004.4.6.10.1.1.3 | ColumnrcMirrBitsLocPort | read-write | current | The local IP port to listen to UDP datagrams. |
| 1.3.6.1.4.1.15004.4.6.10.1.1.4 | ColumnrcMirrBitsRemPort | read-write | current | The Remote port to which protocol on this port can exchange UDP datagrams. |
| 1.3.6.1.4.1.15004.4.6.10.1.1.5 | ColumnrcMirrBitsIpAdd | read-write | current | The IP Address of interface to listen to UDP datagrams. |
| 1.3.6.1.4.1.15004.4.6.10.1.1.6 | ColumnrcMirrBitsLinkStats | read-write | current | Enables links statistics collection. |
| 1.3.6.1.4.1.15004.4.6.11 | IdentityrcTelnetComport | current | Tha main subtree for managing the TelnetPortComport protocol settings on RuggedCom serial devices. | |
| 1.3.6.1.4.1.15004.4.6.11.1 | TablercTelnetComportTable | not-accessible | current | This table provides a list of port entries configured for TelnetPort Comport serial protocolwith configuration options. |
| 1.3.6.1.4.1.15004.4.6.11.1.1 | RowrcTelnetComportEntry | not-accessible | current | List of ports with configuration options for TelnetPortComports serial protocol. |
| 1.3.6.1.4.1.15004.4.6.11.1.1.1 | ColumnrcTelnetComportPort | not-accessible | current | Thephysical Serial Port Number for which this Entry contains the TelnetPortComport serial protocol configuration settings. |
| 1.3.6.1.4.1.15004.4.6.11.1.1.2 | ColumnrcTelnetComportPackChar | read-write | current | The character that can be used to force forwarding of accumulated data to the network. If a packetization character is not configured - object is set to the va… |
| 1.3.6.1.4.1.15004.4.6.11.1.1.3 | ColumnrcTelnetComportPackTimer | read-write | current | The delay from the last received character until when data is forwarded. |
| 1.3.6.1.4.1.15004.4.6.11.1.1.4 | ColumnrcTelnetComportPackSize | read-write | current | The maximum number of bytes received from serial port to be packed in one IP packet. |
| 1.3.6.1.4.1.15004.4.6.11.1.1.5 | ColumnrcTelnetComportFlowControl | read-write | current | The type of FlowControl to be used on the port. |
| 1.3.6.1.4.1.15004.4.6.11.1.1.6 | ColumnrcTelnetComportCallDir | read-write | current | Defines following: - whether to accept an incoming connection 'in(0)' or - to place an outgoing connection 'out(1)' or - to place an outgoing connection and wa… |
| 1.3.6.1.4.1.15004.4.6.11.1.1.7 | ColumnrcTelnetComportLocPort | read-write | current | The local IP port to listen to an incoming TCP connection. |
| 1.3.6.1.4.1.15004.4.6.11.1.1.8 | ColumnrcTelnetComportRemPort | read-write | current | The remote TCP port to use when placing an outgoing connection. |
| 1.3.6.1.4.1.15004.4.6.11.1.1.9 | ColumnrcTelnetComportIpAdd | read-write | current | Defines the IpAddress based on the following: - For outgoing TCP connection (client) 'rcRawSockCallDir' is 'out(2)' this is the remote IP address to communicat… |
| 1.3.6.1.4.1.15004.4.6.11.1.1.10 | ColumnrcTelnetComportLinkStats | read-write | current | Enables links statistics collection. |
| 1.3.6.1.4.1.15004.4.6.15 | IdentityrcConnStats | current | The main subtree for the information about Connection Statistics for RuggedCom serial devices. | |
| 1.3.6.1.4.1.15004.4.6.15.1 | TablercConnStatsTable | not-accessible | current | This table provides the statictics information for all active TCP connections on the RuggedCom serial device. |
| 1.3.6.1.4.1.15004.4.6.15.1.1 | RowrcConnStatsEntry | not-accessible | current | List of parameters providing the statictics information for all active TCP connections on the RuggedCom serial device. |
| 1.3.6.1.4.1.15004.4.6.15.1.1.1 | ColumnrcConnStatsRemIp | not-accessible | current | The remote IP address of the TCP connection. |
| 1.3.6.1.4.1.15004.4.6.15.1.1.2 | ColumnrcConnStatsRemPort | not-accessible | current | The remote port number of the connection. |
| 1.3.6.1.4.1.15004.4.6.15.1.1.3 | ColumnrcConnStatsLocPort | not-accessible | current | The local port number of the connection. |
| 1.3.6.1.4.1.15004.4.6.15.1.1.4 | ColumnrcConnStatsRxPkts | read-only | current | The number of received packets. |
| 1.3.6.1.4.1.15004.4.6.15.1.1.5 | ColumnrcConnStatsTxPkts | read-only | current | The number of transmitted packets. |
| 1.3.6.1.4.1.15004.4.6.16 | IdentityrcSerDeviceCmnd | current | The main subtree for serial port control commands | |
| 1.3.6.1.4.1.15004.4.6.16.1 | ScalarrcSerDeviceCmndResetPort | read-write | current | The list of ports for which Reset should be performed on the RuggedCom Serial devices. A read attempt for this object always returns an empty list of ports. |
| 1.3.6.1.4.1.15004.4.6.16.2 | ScalarrcSerDeviceCmndClearStats | read-write | current | The list of ports for which Clearing statistics command should be performed on the RuggedCom Serial devices. A read attempt for this object always returns an e… |
| 1.3.6.1.4.1.15004.4.6.18 | NodercSerialConformance | |||
| 1.3.6.1.4.1.15004.4.6.18.2 | NodercSerialGroups | |||
| 1.3.6.1.4.1.15004.4.6.18.2.1 | GrouprcSerialPortParamsGroup | current | Objects related to global settings for RuggedCom serial devices. | |
| 1.3.6.1.4.1.15004.4.6.18.2.2 | GrouprcSerialMbServerGroup | current | Objects related to settings ModBus Server protocol for RuggedCom serial devices. | |
| 1.3.6.1.4.1.15004.4.6.18.2.3 | GrouprcSerialMbClientGroup | current | Objects related to settings ModBus client protocol for RuggedCom serial devices. | |
| 1.3.6.1.4.1.15004.4.6.18.2.4 | GrouprcSerialRawSocketGroup | current | Objects related to settings for raw Socket protocol on RuggedCom serial devices. | |
| 1.3.6.1.4.1.15004.4.6.18.2.5 | GrouprcSerialPreEmpRawSockGroup | current | Objects related to settings for Preemptive Raw Socket serial protocol on RuggedCom serial devices. | |
| 1.3.6.1.4.1.15004.4.6.18.2.6 | GrouprcSerialTinAndWinGroup | current | Objects related to settings for Tin and Win protocols on RuggedCom serial devices. | |
| 1.3.6.1.4.1.15004.4.6.18.2.7 | GrouprcSerialMicrolokGroup | current | Objects related to settings for Microlok protocols on RuggedCom serial devices. | |
| 1.3.6.1.4.1.15004.4.6.18.2.8 | GrouprcSerialDnpGroup | current | Objects related to settings for Dnp protocols on RuggedCom serial devices. | |
| 1.3.6.1.4.1.15004.4.6.18.2.9 | GrouprcSerialDnpRsGroup | current | Objects related to settings for Dnp over Raw Socket protocol on RuggedCom serial devices. | |
| 1.3.6.1.4.1.15004.4.6.18.2.10 | GrouprcSerialMirrBitsGroup | current | Objects related to settings for Mirrored Bits protocol on RuggedCom serial devices. | |
| 1.3.6.1.4.1.15004.4.6.18.2.11 | GrouprcSerialTelnetComportGroup | current | Objects related to settings for TelnetPortComport protocol on RuggedCom serial devices. | |
| 1.3.6.1.4.1.15004.4.6.18.2.15 | GrouprcSerialConnStatsGroup | current | Objects related to Connection Statistics from Serial protocol on RuggedCom serial devices. | |
| 1.3.6.1.4.1.15004.4.6.18.2.16 | GrouprcSerialCommandsGroup | current | Objects related to Serial Port Commands on RuggedCom serial devices. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| EnabledStatus | INTEGER { enabled(1), disabled(2) } | current | A simple status value for the object. |
| RcCallDir | INTEGER { in(0), out(1), both(2) } | current | Call Direction options for a RuggedCom Serial Server device. |
| RcFlowControl | INTEGER { none(1), xonXoff(2) } | current | FlowControl setting for serial port. |
| RcSerPortType | INTEGER { none(0), rs232(1), rs485(2), rs422(3), tpc(4), fiber(5) } rcSerialPortParams OBJECT-IDENTITY STATUS current DESCRIPTION "The main subtree for managing Global Serial Port parameters." ::= { rcSerial 1 } rcMbServer OBJECT-IDENTITY STATUS current DESCRIPTION "The main subtree for managing the Modbus Protocol Server settings on RuggedCom serial Devices." ::= { rcSerial 2 } rcMbClient OBJECT-IDENTITY STATUS current DESCRIPTION "The main subtree for managing the Modbus Protocol Client Settings on RuggedCom serial devices." ::= { rcSerial 3 } rcRawSock OBJECT-IDENTITY STATUS current DESCRIPTION "The main subtree for managing the Raw Socket Protocol Settings on RuggedCom serial devices." ::= { rcSerial 4 } rcPreemptRS OBJECT-IDENTITY STATUS current DESCRIPTION "The main subtree for managing the Preemptive Raw Socket Protocol settings on RuggedCom serial devices." ::= { rcSerial 5 } rcTinAndWin OBJECT-IDENTITY STATUS current DESCRIPTION "The main subtree for managing the TIN and WIN protocol settings on RuggedCom serial devices." ::= { rcSerial 6 } rcMicrolok OBJECT-IDENTITY STATUS current DESCRIPTION "The main subtree for managing the Microlok protocol settings on RuggedCom serial devices." ::= { rcSerial 7 } rcDnp OBJECT-IDENTITY STATUS current DESCRIPTION "Tha main subtree for managing the Dnp protocol settings on RuggedCom serial devices." ::= { rcSerial 8 } rcDnpRs OBJECT-IDENTITY STATUS current DESCRIPTION "Tha main subtree for managing the Dnp over Raw Socket protocol settings on RuggedCom serial devices." ::= { rcSerial 9 } rcMirrorBits OBJECT-IDENTITY STATUS current DESCRIPTION "Tha main subtree for managing the Mirrored Bit protocol settings on RuggedCom serial devices." ::= { rcSerial 10 } rcTelnetComport OBJECT-IDENTITY STATUS current DESCRIPTION "Tha main subtree for managing the TelnetPortComport protocol settings on RuggedCom serial devices." ::= { rcSerial 11 } rcConnStats OBJECT-IDENTITY STATUS current DESCRIPTION "The main subtree for the information about Connection Statistics for RuggedCom serial devices." ::= { rcSerial 15 } rcSerDeviceCmnd OBJECT-IDENTITY STATUS current DESCRIPTION "The main subtree for serial port control commands" ::= { rcSerial 16} | current | Serial Port Type for RuggedCom Serial Server device. |
| RcSerProtocol | INTEGER { noProtocol(1), rawSock(2), modbusServer(3), modbusClient(4), itcsWIN(5), itcsTIN(6), microlok(7), dnp(8), dnpRawSock(9), mirrorBits(10), preemptRawSock(11), telnetComport(12) } | current | Serial Protocols permitted for RuggedCom Serial Device Servers. |
| RcTransport | INTEGER { udp(1), tcp(2) } | current | Transport protocol used for IP traffic. |