SBE-MIB
266 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.1055 | Nodesbe | |||
| 1.3.6.1.4.1.1055.1 | Nodesystem | |||
| 1.3.6.1.4.1.1055.1.1 | ScalarsyDateTime | read-write | mandatory | Default value on nX: zero On nX: stored in clock chip Format: Century, year, month, day, hour, min, sec. each occupies one octet in binary value. |
| 1.3.6.1.4.1.1055.1.3 | ScalarsyRAMConfigurationChangedFlag | read-only | mandatory | Default value on nX: set to 'same' when booted from flash, 'different' otherwise On nX: (not needed?) in ram, field trial 2 This field is used by Workshop to d… |
| 1.3.6.1.4.1.1055.1.5 | ScalarsyConfigurationLockFlag | read-write | mandatory | Default value on nX: 'unlocked(2)' This field is used by Workshop to determine whether the nX unit is enabled to allow configuration. When this field is set to… |
| 1.3.6.1.4.1.1055.1.7 | ScalarsyModel | read-only | mandatory | Default value on nX: factory setting On nX: in flash, field trial 1 The product name, hardware revision, firmware revision, and kernel revision for the nX Node… |
| 1.3.6.1.4.1.1055.1.10 | ScalarsyBootInfo | read-only | deprecated | THIS ITEM IS NOT IMPLEMENTED! |
| 1.3.6.1.4.1.1055.1.11 | ScalarsyActivatedLevel | read-write | mandatory | Software feature activation level information. This entry is maintained and used by Workshop. |
| 1.3.6.1.4.1.1055.1.12 | ScalarsySerialNumber | read-only | mandatory | A manufacturing only mib that will return the serial number of the board. This function is reserved for manufacturing test and may change as needed by manufact… |
| 1.3.6.1.4.1.1055.1.13 | ScalarsyBaseActivationLevel | read-only | mandatory | Base level software feature information. This entry is maintained by the nX unit and used by Workshop. |
| 1.3.6.1.4.1.1055.2 | Noderouter | |||
| 1.3.6.1.4.1.1055.2.1 | Noderoutsys | |||
| 1.3.6.1.4.1.1055.2.1.1 | ScalarsyBootOrder | read-write | mandatory | enum values per octet: 1=Flash, 2=TFTP, 3=PCMCIA, 4=LAN, 0=none Default value on nX: (Flash) On nX: in flash This field has one octet for each boot source from… |
| 1.3.6.1.4.1.1055.2.1.2 | ScalarsyMtuMru | read-only | mandatory | Default value on nX: 1500 On nX: both ram and flash, field trial 2 This field specifies the maximum size frame that the nX product will send or receive, either… |
| 1.3.6.1.4.1.1055.2.1.3 | ScalarsyEventToLogThreshold | read-write | mandatory | Default value on nX: 3 On nX: both ram and flash, field trial 2 All events generated by the nX product have an associated severity level which ranges from 1 to… |
| 1.3.6.1.4.1.1055.2.1.5 | ScalarsyEventToTrapThreshold | read-write | mandatory | Default value on nX: 6 On nX: both ram and flash, field trial 2 All events generated by the nX product have an associated severity level which ranges from 1 to… |
| 1.3.6.1.4.1.1055.2.1.7 | ScalarsyControlOperation | read-write | mandatory | Default value on nX: 'none' On nX: in ram, field trial 1 except for Clear-SNMP-statistics and Disable-port-after-call which are field trial 2 This object is se… |
| 1.3.6.1.4.1.1055.2.1.8 | ScalarsyControlVariableStringOne | read-write | mandatory | Default Value on nX: N/A On nX: in ram, field trial 1 This object is used to store a DisplayString parameter to a control operation. Once the control operation… |
| 1.3.6.1.4.1.1055.2.1.9 | ScalarsyControlVariableIntegerOne | read-write | mandatory | Default Value on nX: N/A On nX: in ram, field trial 1 This object is used to store an Integer parameter to a control operation. Once the control operation is s… |
| 1.3.6.1.4.1.1055.2.1.10 | ScalarsyDialinAuthentication | read-write | mandatory | Default value on nX: 'none' On nX: both ram and flash. This field identifies the type of authentication negotiation that is to be performed during dialin to th… |
| 1.3.6.1.4.1.1055.2.1.11 | ScalarsyEventToSpeakThreshold | read-write | mandatory | Default value on nX: 6 On nX: both ram and flash, field trial 2 All events generated by the nX product have an associated severity level which ranges from 1 to… |
| 1.3.6.1.4.1.1055.2.1.12 | ScalarsyNumberOfTimesToSpeak | read-write | mandatory | Default value on nX: 3 On nX: both ram and flash, field trial 2 This item specifies the number of times an error code is spoken |
| 1.3.6.1.4.1.1055.2.1.13 | ScalarsySaveRamToFlashState | read-only | mandatory | This item specifies the state of the operation ram-to-Flash in the item syControlOperation. The valid states are: updating and idle. updating state indicates t… |
| 1.3.6.1.4.1.1055.2.1.14 | ScalarsyDialbackRetryInterval | read-write | mandatory | This item specifies the number of seconds to pause before the next dialback call from Soho will be made. Default = 10 |
| 1.3.6.1.4.1.1055.2.1.15 | ScalarsyDialbackRetryLimit | read-write | mandatory | This item specifies the number of times that Soho will retry dialback call from Soho. Default is 3. |
| 1.3.6.1.4.1.1055.2.1.16 | ScalarsyReverseCallbackTimeout | read-write | mandatory | Default value on nX: 60 (seconds) Specifies the number of seconds to wait for an expected reverse callback before redialing. |
| 1.3.6.1.4.1.1055.2.2 | Nodebridge | |||
| 1.3.6.1.4.1.1055.2.2.1 | ScalarsyBridgeConfiguredFlag | read-write | mandatory | Default value on nX: 'yes' On nX: both ram and flash, field trial 2 If this object is 'no', syBridgeFilterFlag will be returned as 'other' by default regardles… |
| 1.3.6.1.4.1.1055.2.2.2 | ScalarsyBridgeFilterFlag | read-write | mandatory | Default value on nX: 'all' On nX: both ram and flash, field trial 2 This value indicates the bridging rule for this nX product, whether to include or exclude p… |
| 1.3.6.1.4.1.1055.2.2.3 | ScalarsyBridgePriority | read-write | mandatory | Default value on nX: 32768 On nX: both ram and flash Used by the Spanning Tree Algorithm to determine who is the root bridge in the network. |
| 1.3.6.1.4.1.1055.2.2.4 | TablesyBridgeTable | not-accessible | mandatory | Bridge table - one copy |
| 1.3.6.1.4.1.1055.2.2.4.1 | RowsyBridgeEntry | not-accessible | mandatory | The bridge table information for one protocol. |
| 1.3.6.1.4.1.1055.2.2.4.1.1 | ColumnsyBridgeStatus | read-write | mandatory | Indication of whether or not a valid entry. |
| 1.3.6.1.4.1.1055.2.2.4.1.2 | ColumnsyBridgeProtocol | read-only | mandatory | Default value on nX: none On nX: both ram and flash, field trial 2 This column item contains the protocol number for a protocol to be bridged. Bridging rules a… |
| 1.3.6.1.4.1.1055.2.3 | Nodeip | |||
| 1.3.6.1.4.1.1055.2.3.1 | ScalaripConfiguredFlag | read-write | mandatory | Default value on nX: 'no' On nX: both ram and flash, field trial 1 This object is 'no' if IP is not configured for this LX-Product, 'yes' if it is configured. |
| 1.3.6.1.4.1.1055.2.3.2 | ScalaripLANAddress | read-write | mandatory | Default value on nX: 0 On nX: both ram and flash, field trial 1 If IP is configured, this object contains the IP address for the nX product's ethernet port and… |
| 1.3.6.1.4.1.1055.2.3.3 | ScalaripLANSubnetMask | read-write | mandatory | Default value on nX: N/A Default value in Workshop: 0 On nX: both ram and flash, field trial 1 If IP is configured, this object contains the subnet mask which … |
| 1.3.6.1.4.1.1055.2.3.4 | ScalaripBroadcastAddress | read-write | mandatory | Default value on nX: 0 Default value in Workshop: 0 On nX: both ram and flash, field trial 1 If IP is configured, this object contains the IP address which the… |
| 1.3.6.1.4.1.1055.2.3.5 | ScalaripDefaultGateway | read-write | mandatory | Default value on nX: N/A Default value in Workshop: 0 On nX: both ram and flash, field trial 2 If IP is configured, this object contains the network address to… |
| 1.3.6.1.4.1.1055.2.3.6 | ScalaripRipReceiveAdvertisementFlag | read-write | mandatory | Default value on nX: 'yes' On nX: both ram and flash, field trial 2 If IP is configured, this object determines whether or not the nX product will accept IP RI… |
| 1.3.6.1.4.1.1055.2.3.7 | ScalaripRipSendInterval | read-write | mandatory | Default value on nX: 30 On nX: both ram and flash, field trial 2 If IP is configured, this object determines time, in seconds, between nX broadcasts of the IP … |
| 1.3.6.1.4.1.1055.2.3.8 | ScalaripDefaultGatewayType | read-write | mandatory | Default value on nX: NONE On nX: both ram and flash, field trial 2 If nX cannot determine a route for the packet from its routing table (both static and dynami… |
| 1.3.6.1.4.1.1055.2.3.9 | ScalaripWanDestinationName | read-write | mandatory | Same as destName in the Destination Table. |
| 1.3.6.1.4.1.1055.2.3.10 | ScalaripWanUserName | read-write | mandatory | Same as userName in the User Table. |
| 1.3.6.1.4.1.1055.2.3.11 | ScalaripStaticRouteMaxEntry | read-only | mandatory | maximum # of entry allowed in the ipStaticRouteTable. Default to 32. |
| 1.3.6.1.4.1.1055.2.3.12 | TableipStaticRouteTable | not-accessible | mandatory | IP Static Route table - one copy per IP port. |
| 1.3.6.1.4.1.1055.2.3.12.1 | RowipStaticRouteEntry | not-accessible | mandatory | The static route information for one route for this port. |
| 1.3.6.1.4.1.1055.2.3.12.1.1 | ColumnipStaticRouteStatus | read-write | mandatory | Indication of whether or not a valid entry. |
| 1.3.6.1.4.1.1055.2.3.12.1.2 | ColumnipStaticRouteDestinationAddress | read-only | mandatory | This is a destination network or host IP address. Packets that the nX product processes for this address will be routed as indicated by the remaining entries i… |
| 1.3.6.1.4.1.1055.2.3.12.1.3 | ColumnipStaticRouteDestinationSubnetMask | read-write | mandatory | Workshop should display by default the subnet mask based on class of destination IP address, the nX should not assume any default subnet value. This subnet mas… |
| 1.3.6.1.4.1.1055.2.3.12.1.4 | ColumnipStaticRouteDestinationHopCount | read-write | mandatory | The value of this object indicates the number of hops between the nX product and the IP Destination Address. The hop count is often used as an indicator of the… |
| 1.3.6.1.4.1.1055.2.3.12.1.5 | ColumnipStaticRouteDestinationName | read-write | mandatory | Same as destName in the Destination Table. |
| 1.3.6.1.4.1.1055.2.3.12.1.6 | ColumnipStaticRouteNetworkInterface | read-write | mandatory | Indication of which interface type to route this packet to. If LAN is defined, ipStaticRouteGateway must be defined. Otherwise, at least one of ipStaticRouteUs… |
| 1.3.6.1.4.1.1055.2.3.12.1.7 | ColumnipStaticRouteUserName | read-write | mandatory | Same as userName in the User Table. |
| 1.3.6.1.4.1.1055.2.3.12.1.8 | ColumnipStaticRouteGateway | read-write | mandatory | This is the Gateway IP address of the static route. |
| 1.3.6.1.4.1.1055.2.3.13 | ScalaripDefaultGatewayIfType | read-write | mandatory | Default value on nX: NONE If nX cannot determine a route for the packet from its routing table (both static and dynamic), the packet will be sent to a Default … |
| 1.3.6.1.4.1.1055.2.3.14 | ScalaripBroadcastForwardTypes | read-write | mandatory | Default value on nX: 0 This is a bit encoded value representing the types of IP broadcast forwarding over WAN to be enabled. This is a global setting for the N… |
| 1.3.6.1.4.1.1055.2.4 | Nodeipx | |||
| 1.3.6.1.4.1.1055.2.4.1 | ScalaripxConfiguredFlag | read-write | mandatory | Default value on nX: 'ipx-and-auto-learn-both-off (1)' On nX: both ram and flash, This object reflects the state of ipx and auto-learning configuration as desc… |
| 1.3.6.1.4.1.1055.2.4.8 | ScalaripxNetbios | read-write | mandatory | Default value on nX: no (1) This object reflects the state of NetBIOS (IPX Type20) frame forwarding for the NX. NetBIOS forwarding is enabled for a specific si… |
| 1.3.6.1.4.1.1055.2.4.9 | TableipxMultiFrameTable | not-accessible | mandatory | IPX multifram type support, the table contains fix size of 4 entries. They can not be added or deleted. |
| 1.3.6.1.4.1.1055.2.4.9.1 | RowipxMultiFrameEntry | not-accessible | mandatory | The community information for this community. |
| 1.3.6.1.4.1.1055.2.4.9.1.1 | ColumnipxMultiFrameStatus | read-write | mandatory | Indication of whether or not a valid entry. User can only use Modify |
| 1.3.6.1.4.1.1055.2.4.9.1.2 | ColumnipxMultiFrameType | read-only | mandatory | Default value on nX: IEEE 802.2 |
| 1.3.6.1.4.1.1055.2.4.9.1.3 | ColumnipxMultiFrameSelectFlag | read-write | mandatory | Default value on nX: there must be at least a entry is = yes |
| 1.3.6.1.4.1.1055.2.4.9.1.4 | ColumnipxMultiFrameNetworkAddress | read-write | mandatory | Default value on nX: 0 If IPX Manual Set Network Address is set to 'yes', this object specifies the IPX Network Address that the nX product will use for packet… |
| 1.3.6.1.4.1.1055.2.4.11 | ScalaripxNetAddressAutoLearnStateCounter | read-only | mandatory | Default value on nX: 0 If IPX is configured, and Auto learn is Yes. this object determines the time (in sec) remaining in the IPX auto learn phase. If the valu… |
| 1.3.6.1.4.1.1055.2.5 | Nodewan | |||
| 1.3.6.1.4.1.1055.2.5.1 | TablewanPortTable | not-accessible | mandatory | Each WAN port's information is contained in a row in a SNMP table. The following describes the columns in the table. Each row is uniquely identified by its Wan… |
| 1.3.6.1.4.1.1055.2.5.1.2 | RowwanPortEntry | not-accessible | mandatory | The WAN table information for one WAN port. |
| 1.3.6.1.4.1.1055.2.5.1.2.1 | ColumnwanPortEntryStatus | read-write | mandatory | Indication of whether or not a valid entry. |
| 1.3.6.1.4.1.1055.2.5.1.2.2 | ColumnwanPortNumber | read-only | mandatory | Default value on nX: ascending integer, one for each hardware WAN port: 1, 2, 3A, 3B, 4A, and 4B. On nX: both ram and flash, field trial 1 This field is used t… |
| 1.3.6.1.4.1.1055.2.5.1.2.3 | ColumnwanPortEnabled | read-only | mandatory | Default value on nX: disabled On nX: both ram and flash, field trial 1 If this value is 'enabled', the Wan port is enabled. If this value is 'disabled', if the… |
| 1.3.6.1.4.1.1055.2.5.1.2.4 | ColumnwanDefaultDialinIPAddress | read-write | mandatory | Default value on nX: all zero On nX: both ram and flash, field trial 1 If IP is configured, this field is required and is used as the default IP address of the… |
| 1.3.6.1.4.1.1055.2.5.1.2.5 | ColumnwanDefaultDialinSubnetMask | read-write | mandatory | Default value on nX: all zero Default value in Workshop: 1's, based on Default Dialin IP Address class On nX: both ram and flash, field trial 1 If the Default … |
| 1.3.6.1.4.1.1055.2.5.1.2.6 | ColumnwanDefaultIPXNetworkAddress | read-only | mandatory | Default value on nX: 0 On nX: in ram, field trial 1 If IPX is configured, this field indicates which IPX network address is being used by this port. The nX wil… |
| 1.3.6.1.4.1.1055.2.5.1.2.7 | ColumnwanDefaultDialinIPXNodeAddress | read-only | mandatory | Default value on nX: 0 On nX: in ram, field trial 1 If IPX is configured, this field specifies the IPX node address that is being used by this port. The nX wil… |
| 1.3.6.1.4.1.1055.2.5.1.2.8 | ColumnwanDialinAllowedFlag | read-write | mandatory | Default value on nX : 'yes' On nX: both ram and flash, field trial 2 If this flag is 'yes', dialin access is allowed on this port. |
| 1.3.6.1.4.1.1055.2.5.1.2.9 | ColumnwanDialoutAllowedFlag | read-write | mandatory | Default value on nX : 'yes' On nX: both ram and flash, field trial 2 If this flag is 'yes', dialout is allowed on this port. |
| 1.3.6.1.4.1.1055.2.5.1.2.10 | ColumnwanLinkLayerType | read-write | mandatory | Default value on nX: async On nX: both ram and flash, field trial 1 This object identifies the type of communication link that is used by this WAN port. Some d… |
| 1.3.6.1.4.1.1055.2.5.1.2.11 | ColumnwanLinkLayerNRZFlag | read-write | mandatory | Default value on nX: nrz On nX: both ram and flash If appropriate for the Link Line Type, this flag identifies whether the line is nrz or nrzi. (See Destinatio… |
| 1.3.6.1.4.1.1055.2.5.1.2.12 | ColumnwanLinkLayerProtocolType | read-write | mandatory | Default value on nX: ppp On nX: both ram and flash, This flag identifies whether the Link Line Type is ppp. Other options are not supported at this time. |
| 1.3.6.1.4.1.1055.2.5.1.2.13 | ColumnwanLinkDialupFlag | read-write | mandatory | Default value on nX: dialup dtr-dial(3) is obsolete (3/4/96) On nX: both ram and flash, field trial 1 (may be encoded into Link Layer Type) If appropriate for … |
| 1.3.6.1.4.1.1055.2.5.1.2.14 | ColumnwanModemName | read-write | mandatory | Default value on nX: empty On nX: both ram and flash, field trial 1 This object contains the ASCII name of the modem. It is used by Workshop to determine the i… |
| 1.3.6.1.4.1.1055.2.5.1.2.15 | ColumnwanModemSpeed | read-write | mandatory | Default value on nX: 9600 On nX: both ram and flash, field trial 1 This object contains an indicator of the speed at which the nX product should communicate wi… |
| 1.3.6.1.4.1.1055.2.5.1.2.16 | ColumnwanModemInitializationString | read-write | mandatory | Default value on nX: empty On nX: both ram and flash, field trial 1 This object contains the ASCII string that is to be sent to the modem whenever the modem is… |
| 1.3.6.1.4.1.1055.2.5.1.2.17 | ColumnwanModemDialPrefix | read-write | mandatory | Default value on nX: empty On nX: both ram and flash, field trial 1 This is set by the user. It contains the modem's dial command (e.g. ATDT or ATDP) possibly … |
| 1.3.6.1.4.1.1055.2.5.1.2.18 | ColumnwanPortType | read-only | mandatory | Default value on nX: determined by hardware Workshop no longer sets this field This value indicates whether the port is PCMCIA, or a D-shell connection - eithe… |
| 1.3.6.1.4.1.1055.2.5.1.2.19 | ColumnwanPCMCIACardName | read-only | mandatory | Default value on nX: empty string if card not present, else product information from card On nX: from 'ram' (actually hardware), field trial 1 Workshop no long… |
| 1.3.6.1.4.1.1055.2.5.1.2.20 | ColumnwanIpRipReceiveAdvertisementFlag | read-write | mandatory | Default value on nX: 'yes' On nX: both ram and flash, field trial 2 If IP is configured, this object determines whether or not the nX product will accept IP RI… |
| 1.3.6.1.4.1.1055.2.5.1.2.21 | ColumnwanIpRipSendInterval | read-write | mandatory | Default value on nX: 30 On nX: both ram and flash, field trial 2 If IP is configured, this object determines time, in seconds, between nX broadcasts of the IP … |
| 1.3.6.1.4.1.1055.2.5.1.2.22 | ColumnwanIpxRipReceiveBroadcastFlag | read-write | mandatory | Default value on nX: ''yes' On nX: both ram and flash, field trial 2 If IPX is configured, this object determines whether or not the nX product will accept IPX… |
| 1.3.6.1.4.1.1055.2.5.1.2.23 | ColumnwanIpxRipSendInterval | read-write | mandatory | Default value on nX: 60 On nX: both ram and flash, field trial 2 If IPX is configured, this object determines time, in seconds, between nX broadcasts of the IP… |
| 1.3.6.1.4.1.1055.2.5.1.2.24 | ColumnwanIpxSapReceiveAdvertisementFlag | read-write | mandatory | Default value on nX: ''yes' On nX: both ram and flash, field trial 2 If IPX is configured, this object determines whether or not the nX product will accept IPX… |
| 1.3.6.1.4.1.1055.2.5.1.2.25 | ColumnwanIpxSapSendInterval | read-write | mandatory | Default value on nX: 60 On nX: both ram and flash, field trial 2 If IPX is configured, this object determines time, in seconds, between nX broadcasts of the IP… |
| 1.3.6.1.4.1.1055.2.5.1.2.26 | ColumnwanIpxNetbios | read-write | mandatory | Default value on nX: 'no' On nX: both ram and flash, field trial 2 If IPX is configured, this object determines if NetBIOS broadcasts are to be forwarded acros… |
| 1.3.6.1.4.1.1055.2.5.1.2.27 | ColumnwanISDNSwitchType | read-write | mandatory | The particular protocol type supported by the switch providing access to the ISDN network to which this subscriber interface is connected. Note: this entry def… |
| 1.3.6.1.4.1.1055.2.5.1.2.28 | ColumnwanISDNCallingPhoneNoB1 | read-write | mandatory | Default value on nX: empty This item contains the calling phone number for the ISDN B1 channel. |
| 1.3.6.1.4.1.1055.2.5.1.2.29 | ColumnwanISDNCallingPhoneNoB2 | read-write | mandatory | Default value on nX: empty This item contains the calling phone number for the ISDN B1 channel. |
| 1.3.6.1.4.1.1055.2.5.1.2.30 | ColumnwanISDNSPID1 | read-write | mandatory | Default value on nX: empty This item contains the Service Profile Identifiers (SPID) for the ISDN B1 channel. |
| 1.3.6.1.4.1.1055.2.5.1.2.31 | ColumnwanISDNSPID2 | read-write | mandatory | Default value on nX: empty This item contains the Service Profile Identifiers (SPID) for the ISDN B2 channel. |
| 1.3.6.1.4.1.1055.2.5.1.2.32 | ColumnwanPortGroup | read-write | mandatory | Default value on nX: non-group(2) This field is used to identify wether the Wan port is part of the Hunt Group. Port group is used as hunt group in TSD for res… |
| 1.3.6.1.4.1.1055.2.5.1.2.33 | ColumnwanISDNSubAddress1 | read-write | mandatory | Default value on nX: empty This item contains the subaddress for the ISDN B1 channel. |
| 1.3.6.1.4.1.1055.2.5.1.2.34 | ColumnwanISDNSubAddress2 | read-write | mandatory | Default value on nX: empty This item contains the subaddress for the ISDN B2 channel. |
| 1.3.6.1.4.1.1055.2.5.1.2.35 | ColumnwanISDNNTTCard | read-write | mandatory | Default value on nX: no(1) This item indicates whether this is an NTT ISDN card. |
| 1.3.6.1.4.1.1055.2.5.1.2.36 | ColumnwanISDNChannels | read-write | mandatory | Default value on nX: oneb(1) This item indicates the number B channels supported by the ISDN card. |
| 1.3.6.1.4.1.1055.2.5.1.2.37 | ColumnwanEnableDataCompression | read-write | mandatory | Default value on nX: no. this entry indicates whether to perform data compression over the ppp connection. |
| 1.3.6.1.4.1.1055.2.5.1.2.38 | ColumnwanISDNChannelSpeed | read-write | mandatory | Default value on nX: cs64. This entry is used to configure the B channel speed of the ISDN card. |
| 1.3.6.1.4.1.1055.2.5.1.2.39 | ColumnwanUsageMode | read-write | mandatory | Default value on nX: 1 This value indicates how the port is used for modem pooling. If 2 or 3 is set, the GSN and SSN also must be set. Note: This is a bit map… |
| 1.3.6.1.4.1.1055.2.5.1.2.40 | ColumnwanModemPoolGSN | read-write | mandatory | The General Service Name used for this port. Used for Modem pooling |
| 1.3.6.1.4.1.1055.2.5.1.2.41 | ColumnwanModemPoolSSN | read-write | mandatory | The Specific Service Name used for this port. Used for Modem pooling |
| 1.3.6.1.4.1.1055.2.5.2 | TablewanIPAddressTable | not-accessible | mandatory | WanIPAddress table - one copy |
| 1.3.6.1.4.1.1055.2.5.2.1 | RowwanIPAddressEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.1055.2.5.2.1.1 | ColumnwanIPAddressStatus | read-write | mandatory | Indication of whether or not a valid entry. |
| 1.3.6.1.4.1.1055.2.5.2.1.2 | ColumnwanIPAddress | read-only | mandatory | Default value on nX: 0 On nX: both ram and flash, field trial 2 This item specifies an IP address in the shared pool for remote dial-in user. |
| 1.3.6.1.4.1.1055.2.5.3 | TablewanStatPortTable | not-accessible | mandatory | Each WAN port's State and Statistical information is contained in a row in a SNMP table |
| 1.3.6.1.4.1.1055.2.5.3.1 | RowwanStatPortEntry | not-accessible | mandatory | The WAN table information for one WAN port. |
| 1.3.6.1.4.1.1055.2.5.3.1.1 | ColumnwanStatPortEntryStatus | read-write | mandatory | Indication of whether or not a valid entry. This entry is used only to maintain uniformity of all table structures. User can neither delete nor add any entries… |
| 1.3.6.1.4.1.1055.2.5.3.1.2 | ColumnwanStatPortNumber | read-only | mandatory | Same as in wanPortNumber. |
| 1.3.6.1.4.1.1055.2.5.3.1.3 | ColumnwanStatPortState | read-only | mandatory | Default value on nX: disconnected. |
| 1.3.6.1.4.1.1055.2.5.3.1.4 | ColumnwanStatPortUserName | read-only | mandatory | Currently connected Destination name or user name. Null if unknown. |
| 1.3.6.1.4.1.1055.2.5.3.1.5 | ColumnwanStatPortFrameTransmitted | read-write | mandatory | # of frames transmitted out of this port. |
| 1.3.6.1.4.1.1055.2.5.3.1.6 | ColumnwanStatPortFrameReceived | read-write | mandatory | # of frames received from this port. |
| 1.3.6.1.4.1.1055.2.5.3.1.7 | ColumnwanStatPortTransmitError | read-write | mandatory | # of transmit errors detected at this port. |
| 1.3.6.1.4.1.1055.2.5.3.1.8 | ColumnwanStatPortReceiveError | read-write | mandatory | # of receive errors detected at this port. |
| 1.3.6.1.4.1.1055.2.5.3.1.9 | ColumnwanStatPortTransmitQueueFull | read-write | mandatory | # of times transmit queue full detected at this port. |
| 1.3.6.1.4.1.1055.2.5.3.1.10 | ColumnwanStatPortCallOriginated | read-write | mandatory | # of calls originated from this port. Includes both success and fail. |
| 1.3.6.1.4.1.1055.2.5.3.1.11 | ColumnwanStatPortCallAnswered | read-write | mandatory | # of answers succeeded at this port. |
| 1.3.6.1.4.1.1055.2.5.3.1.12 | ColumnwanStatPortNoDialTone | read-write | mandatory | # of calls failed due to no dial tone. also counted also in CallOriginated |
| 1.3.6.1.4.1.1055.2.5.3.1.13 | ColumnwanStatPortNoAnswer | read-write | mandatory | # of calls failed due to no answer from remote. also counted also in CallOriginated |
| 1.3.6.1.4.1.1055.2.5.3.1.14 | ColumnwanStatPortBusyDetected | read-write | mandatory | # of calls failed due to line busy at remote. also counted also in CallOriginated |
| 1.3.6.1.4.1.1055.2.5.3.1.15 | ColumnwanStatPortNoCarrier | read-write | mandatory | # of calls failed due to no carrier. also counted also in CallOriginated |
| 1.3.6.1.4.1.1055.2.5.3.1.16 | ColumnwanStatPortModemSignal | read-only | mandatory | Modem signal state. Bit masked DCD = 1, CTS =2, DTR = 4, RTS = 8, DSR =16 Bit state: 1 = On |
| 1.3.6.1.4.1.1055.2.5.3.1.17 | ColumnwanStatPortConnDirection | read-only | mandatory | Direction of the connection |
| 1.3.6.1.4.1.1055.2.5.3.1.18 | ColumnwanStatPortProtoUp | read-only | mandatory | This item is a bit encoded value representing various protocols, which are currently up over this connection. The encoded values are: IP(1), IPX(2), Bridging(4… |
| 1.3.6.1.4.1.1055.2.5.4 | ScalarwanIPAddressMaxEntry | read-only | mandatory | maximum # of entry allowed in the wanIPAddressTable. |
| 1.3.6.1.4.1.1055.2.6 | Nodedestination | |||
| 1.3.6.1.4.1.1055.2.6.1 | TabledestTable | not-accessible | mandatory | Destination table - one copy |
| 1.3.6.1.4.1.1055.2.6.1.1 | RowdestEntry | not-accessible | mandatory | The information for one destination. |
| 1.3.6.1.4.1.1055.2.6.1.1.1 | ColumndestStatus | read-write | mandatory | Indication of whether or not a valid entry. |
| 1.3.6.1.4.1.1055.2.6.1.1.2 | ColumndestName | read-only | mandatory | Default value on nX: none On nX: both ram and flash, field trial 1 This item contains a user supplied identification for this destination. This should be somet… |
| 1.3.6.1.4.1.1055.2.6.1.1.3 | ColumndestType | read-write | mandatory | Default value on nX: Lan-to-Lan On nX: (not necessary in first release) both ram and flash, field trial 2 This item indicates whether the destination is a LAN … |
| 1.3.6.1.4.1.1055.2.6.1.1.4 | ColumndestDialoutPhoneNumber | read-write | mandatory | Default value on nX: empty On nX: both ram and flash, field trial 1 This item contains the phone number that is to be used to call the destination. This string… |
| 1.3.6.1.4.1.1055.2.6.1.1.5 | ColumndestDialoutProtoSupport | read-write | mandatory | Default value on nX: 0 On nX: both ram and flash, This item is a bit encoded value representing various protocols to be enabled during the establishment of a W… |
| 1.3.6.1.4.1.1055.2.6.1.1.6 | ColumndestDialoutIpxSupport | read-write | mandatory | NOTE: THIS FIELD IS NO LONGER IN USE. The field destDialoutProtoSupport is used to encode all protocols supported. Default value on nX: same as IP Configured F… |
| 1.3.6.1.4.1.1055.2.6.1.1.7 | ColumndestDialoutModemSpeed | read-write | mandatory | Default value on nX: 'unspecified' On nX: both ram and flash, This item allows the user to override the Modem Speed set up for the port for dialout calls to th… |
| 1.3.6.1.4.1.1055.2.6.1.1.8 | ColumndestPppMtuMru | read-write | mandatory | Default value on nX: 1500 On nX: both ram and flash, field trial 2 This field can be used to override the global MTR/MTU. The user should set this field if the… |
| 1.3.6.1.4.1.1055.2.6.1.1.9 | ColumndestDialoutHandshake | read-write | mandatory | Default value on nX: 'none' On nX: both ram and flash, 'none' and 'PAP' for field trial 1 This field identifies the type of authorization negotiation that is t… |
| 1.3.6.1.4.1.1055.2.6.1.1.10 | ColumndestDialoutUserName | read-write | mandatory | Default value on nX: 0 On nX: both ram and flash, field trial 1 This value identifies a User Name for PAP or CHAP dialout to this destination. This entry is on… |
| 1.3.6.1.4.1.1055.2.6.1.1.11 | ColumndestDialoutPassword | read-write | mandatory | Default value on nX: 0 On nX: both ram and flash, field trial 1 This value identifies the user password for PAP or CHAP dialout to this destination. This entry… |
| 1.3.6.1.4.1.1055.2.6.1.1.12 | ColumndestPorts | read-write | mandatory | Default Value on nX: 0. This field indicates the port number associated with this site, if the link characteristic wanLinkDialupFlag is set to dedicated(2). |
| 1.3.6.1.4.1.1055.2.6.1.1.13 | ColumndestMaximumDialoutConnectTime | read-write | mandatory | Default value on nX: 0 On nX: both ram and flash, field trial 1 This object contains, in minutes, the maximum time to leave this connection active for dialout.… |
| 1.3.6.1.4.1.1055.2.6.1.1.14 | ColumndestDialoutStatus | read-only | mandatory | Default value on nX: none This item is used by the Workshop to determine the status of a dialout for this destination. |
| 1.3.6.1.4.1.1055.2.6.1.1.15 | ColumndestDialoutSchedule | read-write | mandatory | Default value on nX: 0 On nX: both ram and flash, field trial 2 This is a one-week bit map, with one bit for every 15 minutes. The string is organized a 8 grou… |
| 1.3.6.1.4.1.1055.2.6.1.1.16 | ColumndestHolidaySchedule | read-write | mandatory | Default value on nX: 0 NO LONGER USED. This item specifies which day's dialout schedule is to be used for holidays. For example, this allows a person to specif… |
| 1.3.6.1.4.1.1055.2.6.1.1.17 | ColumndestLinkLayerNRZFlag | read-write | mandatory | Default value on nX: nrz On nX: both ram and flash, field trial 1 (may be encoded into Link Layer Type) If appropriate for the Link Line Type, this flag identi… |
| 1.3.6.1.4.1.1055.2.6.1.1.18 | ColumndestLinkLayerProtocolType | read-write | mandatory | Default value on nX: ppp On nX: both ram and flash, This flag identifies whether the Link Line Type is ppp. Other options are not supported at this time. |
| 1.3.6.1.4.1.1055.2.6.1.1.19 | ColumndestLinkDialupFlag | read-write | mandatory | Default value on nX: dialup On nX: both ram and flash, field trial 1 (may be encoded into Link Layer Type) If appropriate for the Link Line Type, this flag ide… |
| 1.3.6.1.4.1.1055.2.6.1.1.20 | ColumndestPortType | read-write | mandatory | Default value on nX: determined by hardware On nX: from 'ram' (actually hardware), field trial 2 This value indicates whether the dest port is PCMCIA, or a D-s… |
| 1.3.6.1.4.1.1055.2.6.1.1.21 | ColumndestLinkLayerType | read-write | mandatory | Default value on nX: async On nX: both ram and flash, field trial 1 This object identifies the type of communication link that is used by this destination. Som… |
| 1.3.6.1.4.1.1055.2.6.1.1.22 | ColumndestDialoutStatusData | read-only | mandatory | It has the same format as the event messages: Message # : 2 bytes Date/Time stamping: 4 bytes (integer, msb first) Length: n bytes defining the size of the par… |
| 1.3.6.1.4.1.1055.2.6.1.1.23 | ColumndestDialoutScheduleFlag | read-write | mandatory | Default value on nX: disable |
| 1.3.6.1.4.1.1055.2.6.1.1.24 | ColumndestDialinUserName | read-write | mandatory | This value identifies a User Name for PAP or CHAP dialin to this destination. |
| 1.3.6.1.4.1.1055.2.6.1.1.25 | ColumndestDialinPassword | read-write | mandatory | This value identifies the user password for PAP or CHAP dialin to this destination. |
| 1.3.6.1.4.1.1055.2.6.1.1.26 | ColumndestMaximumDialinConnectTime | read-write | mandatory | This object contains, in minutes, the maximum time to leave this connection active for dialin connections. After the time elapses, the nX will automatically ha… |
| 1.3.6.1.4.1.1055.2.6.1.1.27 | ColumndestTSDFlag | read-write | mandatory | Default value on nX: non-tsd This entry defines this Destination (Site) to be either a TSD or non-TSD site. If TSD site, then destTSDInactivityTime, destTSDMax… |
| 1.3.6.1.4.1.1055.2.6.1.1.28 | ColumndestTSDInactivityTime | read-write | mandatory | This object contains, in minutes, the maximum time. A value of zero means there is no time limit. |
| 1.3.6.1.4.1.1055.2.6.1.1.29 | ColumndestTSDMaxDownTime | read-write | mandatory | A value of zero means there is no time limit. |
| 1.3.6.1.4.1.1055.2.6.1.1.30 | ColumndestTSDPortGroup | read-write | mandatory | Default value on nX: 0. This field is used to identify the Wan port # to which this TSD entry is assigned. port group #128 is used as hunt group in TSD for res… |
| 1.3.6.1.4.1.1055.2.6.1.1.31 | ColumndestManualDialCallback | read-write | mandatory | This item indicates whether callback is enabled in Manual Dial mode. |
| 1.3.6.1.4.1.1055.2.6.1.1.32 | ColumndestAllowDynamicIPAddr | read-write | mandatory | this entry indicates whether the ip address provided by the remote router (through IPCP negotiation), for the use on the local WAN port, is permitted. |
| 1.3.6.1.4.1.1055.2.6.1.1.33 | ColumndestISDNChannels | read-write | mandatory | This entry indicates the number B channels supported by the ISDN card (configured from the port page). |
| 1.3.6.1.4.1.1055.2.6.1.1.34 | ColumndestDialoutPhoneNumber2 | read-write | mandatory | Default value on nX: empty This item contains the second phone number that is to be used to call the destination using the second ISDN B channel. This string c… |
| 1.3.6.1.4.1.1055.2.6.1.1.35 | ColumndestTSDExpectCallback | read-write | mandatory | Default value on nX: no Determines whether to expect a callback. If callback is expected, re-dial should delay as specified by syReverseCallbackDelay |
| 1.3.6.1.4.1.1055.2.6.2 | ScalardestMaxEntry | read-only | mandatory | Max # of entries allowed in Destination table |
| 1.3.6.1.4.1.1055.2.6.3 | TabledestScriptTable | not-accessible | mandatory | Destination script table |
| 1.3.6.1.4.1.1055.2.6.3.2 | RowdestScriptEntry | not-accessible | mandatory | Chat script information for a destination |
| 1.3.6.1.4.1.1055.2.6.3.2.1 | ColumndestScriptEntryStatus | read-write | mandatory | Indication of whether or not a valid entry. |
| 1.3.6.1.4.1.1055.2.6.3.2.2 | ColumndestinationName | read-only | mandatory | Same as destName in the Destination Table. |
| 1.3.6.1.4.1.1055.2.6.3.2.3 | ColumndestScriptUseFlag | read-write | mandatory | This entry indicates whether the script associated with this site should be executed or not. |
| 1.3.6.1.4.1.1055.2.6.3.2.4 | ColumndestScriptTimeout | read-write | mandatory | This field specifies the total time limit allocated for the execution of the script to completion |
| 1.3.6.1.4.1.1055.2.6.3.2.5 | ColumndestScriptName | read-write | mandatory | This entry contains the the name of the script. |
| 1.3.6.1.4.1.1055.2.6.3.2.6 | ColumndestScript | read-write | mandatory | This entry contains the chat script identified by the entry destScriptName. |
| 1.3.6.1.4.1.1055.2.6.3.2.7 | ColumndestScriptStartupCmd | read-write | mandatory | This entry contains the command used to indicate the service type to the ISP, if required. |
| 1.3.6.1.4.1.1055.2.7 | Nodeuser | |||
| 1.3.6.1.4.1.1055.2.7.1 | ScalaruserMaxEntries | read-only | mandatory | A value representing the maximum number of user entries in the user table. |
| 1.3.6.1.4.1.1055.2.7.2 | TableuserTable | not-accessible | mandatory | A list of user entries. The number of entries is given by the value of userNumber. |
| 1.3.6.1.4.1.1055.2.7.2.1 | RowuserEntry | not-accessible | mandatory | A user entry containing objects of users. |
| 1.3.6.1.4.1.1055.2.7.2.1.2 | ColumnuserStatus | read-write | mandatory | A value representing the current status of the user entry for the index value, userName. |
| 1.3.6.1.4.1.1055.2.7.2.1.3 | ColumnuserName | read-only | mandatory | An octet string containing user supplied User Name which identifies a dialin user. On dialin, this is used as the login name for PAP or CHAP. |
| 1.3.6.1.4.1.1055.2.7.2.1.4 | ColumnuserPassword | read-write | mandatory | A display string containing user supplied User Password for user identified by userName. |
| 1.3.6.1.4.1.1055.2.7.2.1.5 | ColumnuserPermissions | read-write | mandatory | A value representing the permissions the user identified by userName has, regarding access to the ports. If none(1) is specified, the user can neither dial out… |
| 1.3.6.1.4.1.1055.2.7.2.1.6 | ColumnuserCallbackType | read-write | mandatory | A value specifiying the type of callback to be used when user identified by userName connects. If none(1) is specified, the connection is maintained, and no ca… |
| 1.3.6.1.4.1.1055.2.7.2.1.7 | ColumnuserPhoneNo | read-write | mandatory | A phone number that is to be used for dialback. |
| 1.3.6.1.4.1.1055.2.7.2.1.8 | ColumnuserDialInMax | read-write | mandatory | A value representing the maximum time in minutes for a dialin connection. |
| 1.3.6.1.4.1.1055.2.7.2.1.10 | ColumnuserIpAddress | read-write | mandatory | A value representing the IP Address to be used for the PPP dial-in connection. |
| 1.3.6.1.4.1.1055.2.8 | Nodemanager | |||
| 1.3.6.1.4.1.1055.2.8.1 | ScalarmgrTimeoutForMACProtocolResponses | read-write | mandatory | Default value on nX: 5 On nX: both ram and flash This object specifies the number of seconds Workshop will wait for a response for a message sent to an nX prod… |
| 1.3.6.1.4.1.1055.2.8.2 | ScalarmgrNumberOfRetriesForMACProtocolResponses | read-write | mandatory | Default value on nX: 3 On nX: both ram and flash This object specifies the number of times Workshop will retry sending to an nX product a message that timed ou… |
| 1.3.6.1.4.1.1055.2.8.3 | ScalarmgrEventPollingInterval | read-write | mandatory | Default value on nX: 120 On nX: both ram and flash, field trial 2 This object specifies an interval, in seconds, at which Workshop will poll the nX product in … |
| 1.3.6.1.4.1.1055.2.9 | Nodeholiday | |||
| 1.3.6.1.4.1.1055.2.9.1 | ScalarholidayMaxEntries | read-only | mandatory | A value representing the maximum number of holiday entries in the holiday table. |
| 1.3.6.1.4.1.1055.2.9.2 | TableholidayTable | not-accessible | mandatory | Holiday table - one copy |
| 1.3.6.1.4.1.1055.2.9.2.1 | RowholidayEntry | not-accessible | mandatory | The holiday information for one date. |
| 1.3.6.1.4.1.1055.2.9.2.1.1 | ColumnholidayStatus | read-write | mandatory | Indication of whether or not a valid entry. |
| 1.3.6.1.4.1.1055.2.9.2.1.2 | ColumnholidayDate | read-only | mandatory | Default value on nX: 0 On nX: both ram and flash, field trial 2 This item specifies a day which is designated as a special dialout day. The nX uses the month a… |
| 1.3.6.1.4.1.1055.2.10 | Nodesnmp | |||
| 1.3.6.1.4.1.1055.2.10.1 | TablesnmpCommunityNameTable | not-accessible | mandatory | Community name table |
| 1.3.6.1.4.1.1055.2.10.1.1 | RowsnmpCommunityNameEntry | not-accessible | mandatory | The community information for this community. |
| 1.3.6.1.4.1.1055.2.10.1.1.1 | ColumnsnmpCommunityNameStatus | read-write | mandatory | Indication of whether or not a valid entry. |
| 1.3.6.1.4.1.1055.2.10.1.1.2 | ColumnsnmpCommunityName | read-only | mandatory | Default value on nX: none On nX: both ram and flash, field trial 1 This item defines a community name to be recognized by the nX Product. For convenience of th… |
| 1.3.6.1.4.1.1055.2.10.1.1.3 | ColumnsnmpCommunityPermission | read-write | mandatory | Default value on nX: Three rows are defined initially, one with each of the above permissions. On nX: both ram and flash This item defines the permission level… |
| 1.3.6.1.4.1.1055.2.10.2 | TablesnmpMacServerTable | not-accessible | mandatory | SNMP MAC server table - one copy |
| 1.3.6.1.4.1.1055.2.10.2.1 | RowsnmpMacServerEntry | not-accessible | mandatory | The SNMP MAC server information for one server. |
| 1.3.6.1.4.1.1055.2.10.2.1.1 | ColumnsnmpMacServerStatus | read-write | mandatory | Indication of whether or not a valid entry. |
| 1.3.6.1.4.1.1055.2.10.2.1.2 | ColumnsnmpMacServerAddress | read-only | mandatory | Default value on nX: none On nX: both ram and flash, field trial 1 This item contains the MAC address of the server to which SNMP traps are to be sent. A value… |
| 1.3.6.1.4.1.1055.2.10.3 | TablesnmpIpServerTable | not-accessible | mandatory | SNMP IP server table - one copy |
| 1.3.6.1.4.1.1055.2.10.3.1 | RowsnmpIpServerEntry | not-accessible | mandatory | The SNMP IP server information for one server. |
| 1.3.6.1.4.1.1055.2.10.3.1.1 | ColumnsnmpIpServerStatus | read-write | mandatory | Indication of whether or not a valid entry. |
| 1.3.6.1.4.1.1055.2.10.3.1.2 | ColumnsnmpIpServerAddress | read-only | mandatory | Default value on nX: 0 On nX: both ram and flash, field trial 1 This item contains the IP address of the server to which SNMP traps are to be sent. A value of … |
| 1.3.6.1.4.1.1055.2.10.4 | ScalarsnmpCommunityNameMaxEntry | read-only | mandatory | Max # of entries allowed in snmpCommunityName table |
| 1.3.6.1.4.1.1055.2.11 | Nodeevent | |||
| 1.3.6.1.4.1.1055.2.11.1 | TableeventTable | not-accessible | mandatory | Event table - one copy |
| 1.3.6.1.4.1.1055.2.11.1.1 | RoweventEntry | not-accessible | mandatory | The event information of one event data. |
| 1.3.6.1.4.1.1055.2.11.1.1.1 | ColumneventGroupIndex | read-only | mandatory | index into the event log table entry. It is a reference point where the SNMP manager will issue the GET NEXT request to get the next group of events. nX needs … |
| 1.3.6.1.4.1.1055.2.11.1.1.2 | ColumneventData | read-only | mandatory | A group of event log entries. Each entry will be one event with the following format: Sequence #: 2 bytes Message # : 2 bytes Date/Time stamping: 4 bytes (inte… |
| 1.3.6.1.4.1.1055.3 | Nodediscovery | |||
| 1.3.6.1.4.1.1055.3.1 | ScalardiscNodeName | read-only | mandatory | The Node Name consists of the hardware type and MAC address as follows: SoHo-001122334455 for SoHo, Central001122334455 for Central Torte-001122334455 for Tort… |
| 1.3.6.1.4.1.1055.3.2 | ScalardiscModel | read-only | mandatory | The Model contains a numeric identifier for the hardware model, as follows: 256 - SoHo, 257 - Central, 258 - Torte (not available), 259 - ROUTEMAN, 260 - ROUTE… |
| 1.3.6.1.4.1.1055.3.3 | ScalardiscProto | read-only | mandatory | The Discover Protocol is the protocol over which the last Get request was received from. |
| 1.3.6.1.4.1.1055.4 | NodefileMgmt | |||
| 1.3.6.1.4.1.1055.4.1 | ScalarsyFMOperation | read-write | mandatory | This object is used to initiate a file management operation. Operations are as described below. If this object is read, other(1) will be returned. |
| 1.3.6.1.4.1.1055.4.2 | ScalarsyFMTimeStamp | read-only | mandatory | This specifies the value of sysUpTime when the most recent file management operation was initiated. |
| 1.3.6.1.4.1.1055.4.3 | ScalarsyFMError | read-only | mandatory | This object identifies the results of the most recent attempt at a file operation. If no file operations have been attempted since the system was initialized, … |
| 1.3.6.1.4.1.1055.4.4 | NodesyFileTransfer | |||
| 1.3.6.1.4.1.1055.4.4.1 | ScalarfileTransferStatus | read-write | mandatory | This identifies the current status of the file Transfer operation. If there is a transfer in progress, this object will have the value inProgress(2). Otherwise… |
| 1.3.6.1.4.1.1055.4.4.2 | ScalarfileTransferStartTime | read-only | mandatory | This specifies the value of sysUpTime when the most recent file Transfer operation was initiated. |
| 1.3.6.1.4.1.1055.4.4.3 | ScalarfileTransferFileLength | read-write | mandatory | This specifies the total Data Length of current file being transferred, in bytes. |
| 1.3.6.1.4.1.1055.4.4.4 | ScalarfileTransferCheckSum | read-write | mandatory | This specifies the CCITT cyclic redundancy checksum of current file being transffered. |
| 1.3.6.1.4.1.1055.4.4.5 | ScalarfileTransferDirection | read-only | mandatory | This identifies the current direction of the file Transfer operation. If there is a transfer in progress, this object will have the value copyingFromLX(2), if … |
| 1.3.6.1.4.1.1055.4.4.6 | ScalarfileTransferLastRcvTime | read-only | mandatory | This specifies the value of sysUpTime when the most recent file Object was received. This value is used to time out the File Transfer operation if no File Obje… |
| 1.3.6.1.4.1.1055.4.4.7 | ScalarfileTransferRemoteAddr | read-only | mandatory | This object specifies the MAC Address of the Remote management stations which initiated the file transfer. |
| 1.3.6.1.4.1.1055.4.4.8 | ScalarfileTransferRemoteFileName | read-write | mandatory | This specifies the path and name of a Remote file residing on the remote management station. sbeFileTransferRemoteAddr For LAN Boot this item MUST be 12 charac… |
| 1.3.6.1.4.1.1055.4.4.9 | ScalarfileTransferLocalFileName | read-write | mandatory | This specifies the name of Local File being transferred. For the File Transfer TO the remote station this becomes the name of the source file. For the FROM ope… |
| 1.3.6.1.4.1.1055.4.4.10 | ScalarfileTransferData | read-write | mandatory | This field contains the data of the file being transfered. The data has a header inside which contains information about the file being transfered and the curr… |
| 1.3.6.1.4.1.1055.4.5 | NodesyFileInfo | |||
| 1.3.6.1.4.1.1055.4.5.1 | ScalarsyFileInfoVersion | read-only | mandatory | The version string from a module header. Example, $Release: 2.0.4a $File: lxkernel.gz $Type: kernelFile $DateTime: 07/09/96 19:11 $ProductType: SoHo $Lic: (C)1… |
| 1.3.6.1.4.1.1055.4.5.2 | ScalarsyFileInfoChecksum | read-only | mandatory | This MIB entry is used to retrieve the Information related to a file on the nX File System. The File information contains version string, checksum and length o… |
| 1.3.6.1.4.1.1055.4.5.3 | ScalarsyFileInfoLength | read-only | mandatory | This MIB entry is used to retrieve the Information related to a file on the nX File System. The File information contains version string, checksum and length o… |
| 1.3.6.1.4.1.1055.4.6 | TablesyDirTable | not-accessible | mandatory | The directory entry of one file. |
| 1.3.6.1.4.1.1055.4.6.1 | RowsyDirEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.1055.4.6.1.1 | ColumnsyDirStatus | read-only | mandatory | |
| 1.3.6.1.4.1.1055.4.6.1.2 | ColumnsyDirName | read-only | mandatory | |
| 1.3.6.1.4.1.1055.4.6.1.3 | ColumnsyDirCompressSize | read-only | mandatory | |
| 1.3.6.1.4.1.1055.4.6.1.4 | ColumnsyDirVersion | read-only | mandatory | |
| 1.3.6.1.4.1.1055.4.6.1.5 | ColumnsyDirUncompressSize | read-only | mandatory | |
| 1.3.6.1.4.1.1055.4.7 | ScalarfileName | read-write | mandatory | This field contains a null terminated string in the format of nnnnnnnn.xxx (DOS format file name). The file name is used by the delete file operation, or the g… |
| 1.3.6.1.4.1.1055.4.8 | ScalarfileNameFrom | read-write | mandatory | This field contains a null terminated string in the format of nnnnnnnn.xxx (DOS format file name). The file name is the old file name used by the rename file o… |
| 1.3.6.1.4.1.1055.4.9 | ScalarfileNameTo | read-write | mandatory | This field contains a null terminated string in the format of nnnnnnnn.xxx (DOS format file name). The file name is the new file name used by the rename file o… |
| 1.3.6.1.4.1.1055.6 | Nodemodempool | |||
| 1.3.6.1.4.1.1055.6.1 | ScalarmodempoolEnabled | read-write | mandatory | Default value on nX: disabled On nX: both ram and flash, field trial 1 If this value is 'enabled', the modem pool is enabled. If this value is 'disabled', if t… |
| 1.3.6.1.4.1.1055.6.2 | ScalarmodempoolNodeName | read-write | mandatory | The nodename contains the modem server name advertised in SAP and UDP broadcasts |
| 1.3.6.1.4.1.1055.6.3 | ScalarmodempoolProtoSupport | read-write | mandatory | Default value on nX: 0 On nX: both ram and flash, This item is a bit encoded value representing various protocols to be used for server advertisement. The enco… |
| 1.3.6.1.4.1.1055.65535 | NodeendOfSBEMib | |||
| 1.3.6.1.4.1.1055.65535.1 | ScalardummyStopperForWorkshopForGetNext | read-only | mandatory |