SK-GE-MIB
209 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | Counter enterprises NetworkAddress OBJECT-TYPE TimeTicks |
| RFC1213-MIB | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.179 | Nodesk | |||
| 1.3.6.1.4.1.179.1 | NodeskSystems | |||
| 1.3.6.1.4.1.179.2 | NodeskMibs | |||
| 1.3.6.1.4.1.179.2.3 | NodeskConcMib | |||
| 1.3.6.1.4.1.179.2.4 | NodeskfddiMib | |||
| 1.3.6.1.4.1.179.2.5 | NodeskGeMib | |||
| 1.3.6.1.4.1.179.2.5.1 | NodeskGeGeneral | |||
| 1.3.6.1.4.1.179.2.5.1.1 | ScalarskGeMibVersion | read-only | mandatory | The version of this MIB (e.g. v1.0). |
| 1.3.6.1.4.1.179.2.5.1.2 | ScalarskGeAction | read-write | mandatory | Returns on query 'idle'. A set to 'idle' does nothing. A set to 'force-trap' transmits the trap specified in skGeTrapForceType. 'save-permanent' saves the seta… |
| 1.3.6.1.4.1.179.2.5.1.3 | ScalarskGeNumber | read-only | mandatory | The number of Gigabit-Ethernet adapters. |
| 1.3.6.1.4.1.179.2.5.1.4 | TableskGeTable | not-accessible | mandatory | Table for general adapter specific information. |
| 1.3.6.1.4.1.179.2.5.1.4.1 | RowskGeEntry | not-accessible | mandatory | Entry of skGeTable. |
| 1.3.6.1.4.1.179.2.5.1.4.1.1 | ColumnskGeIndex | read-only | mandatory | Adapter index (1..n). |
| 1.3.6.1.4.1.179.2.5.1.4.1.2 | ColumnskGeIfIndex | read-only | mandatory | Stores the corresponding ifIndex of the mib-2 interfaces table. If the value cannot be obtained a '0' is stored. |
| 1.3.6.1.4.1.179.2.5.1.4.1.3 | ColumnskGePortNumber | read-only | mandatory | Number of ports per adapter. |
| 1.3.6.1.4.1.179.2.5.1.4.1.4 | ColumnskGeDeviceType | read-only | mandatory | Returns the object identifier of the NIC. If it is unknown 0.0 is returned. |
| 1.3.6.1.4.1.179.2.5.1.4.1.5 | ColumnskGeDriverDescr | read-only | mandatory | A description of the driver (e.g. sk98win - Miniport Gigabit-Ethernet driver). |
| 1.3.6.1.4.1.179.2.5.1.4.1.6 | ColumnskGeDriverVersion | read-only | mandatory | The driver version (e.g. v1.05 beta). |
| 1.3.6.1.4.1.179.2.5.1.4.1.7 | ColumnskGeHwDescr | read-only | mandatory | A description of the device hardware (e.g. SK-NET Genesis Sx Single Port). |
| 1.3.6.1.4.1.179.2.5.1.4.1.8 | ColumnskGeHwVersion | read-only | mandatory | The device hardware version. (e.g. v1.2). |
| 1.3.6.1.4.1.179.2.5.1.4.1.9 | ColumnskGeChipSet | read-only | mandatory | Stores the object identifier of the used chip-set. |
| 1.3.6.1.4.1.179.2.5.1.4.1.10 | ColumnskGeDeviceAction | read-write | mandatory | A set to this variable performs a specific action. A get-request to this variable always returns the idle (1) value. The result of the self-test is stored in s… |
| 1.3.6.1.4.1.179.2.5.1.4.1.11 | ColumnskGeTestResult | read-only | mandatory | Stores the self test result, which was initiated by skGeDeviceAction. The value is a sum and 2 raised the power of the result is added to the sum. A sum of zer… |
| 1.3.6.1.4.1.179.2.5.1.4.1.12 | ColumnskGeBusType | read-only | mandatory | Returns the bus type. |
| 1.3.6.1.4.1.179.2.5.1.4.1.13 | ColumnskGeBusSpeed | read-only | mandatory | Returns the bus speed in MHz (e.g. 33 means a bus speed of 33 MHz). If the value is unknown a 0 is returned. |
| 1.3.6.1.4.1.179.2.5.1.4.1.14 | ColumnskGeBusWidth | read-only | mandatory | Returns the bus width in bits (e.g. 64 means a bus width of 64 bit). If the value is unknown a 0 is returned. |
| 1.3.6.1.4.1.179.2.5.1.5 | ScalarskGeChecksumEntriesNumber | read-only | mandatory | Number of entries in skGeCheckSumTable. |
| 1.3.6.1.4.1.179.2.5.1.6 | TableskGeChecksumTable | not-accessible | mandatory | Table of the adapter hardware checksumming module. |
| 1.3.6.1.4.1.179.2.5.1.6.1 | RowskGeChecksumEntry | not-accessible | mandatory | Entry of the checksum table. |
| 1.3.6.1.4.1.179.2.5.1.6.1.1 | ColumnskGeChecksumGeIndex | read-only | mandatory | Index of the adapter. |
| 1.3.6.1.4.1.179.2.5.1.6.1.2 | ColumnskGeChecksumIndex | read-only | mandatory | Index of the protocol. The indexes have fixed semantics. |
| 1.3.6.1.4.1.179.2.5.1.6.1.3 | ColumnskGeChecksumRxOkCts | read-only | mandatory | Number of received frames for which the protocol checksum verification was successfully performed in hardware. |
| 1.3.6.1.4.1.179.2.5.1.6.1.4 | ColumnskGeChecksumRxUnableCts | read-only | mandatory | Number of received frames for which the protocol checksum verification was left to the protocol. |
| 1.3.6.1.4.1.179.2.5.1.6.1.5 | ColumnskGeChecksumRxErrCts | read-only | mandatory | Number of received frames for which the protocol checksum verification in hardware found an error. |
| 1.3.6.1.4.1.179.2.5.1.6.1.6 | ColumnskGeChecksumTxOkCts | read-only | mandatory | Number of transmitted packets for which the protocol checksum was generated in hardware. |
| 1.3.6.1.4.1.179.2.5.1.6.1.7 | ColumnskGeChecksumTxUnableCts | read-only | mandatory | Number of packets, which could not be sent because the requested generation of the checksum was not possible. |
| 1.3.6.1.4.1.179.2.5.1.7 | ScalarskGeTrapForceType | read-write | mandatory | Stores the trap number and the value list that is to be transmitted. The transmission is initiated with skGeAction (force-trap). Each field in the octet string… |
| 1.3.6.1.4.1.179.2.5.1.8 | ScalarskGeTrapDestEntriesNumber | read-only | mandatory | Number of entries in skGeTrapDestTable. |
| 1.3.6.1.4.1.179.2.5.1.9 | TableskGeTrapDestTable | not-accessible | mandatory | Table of trap destination addresses to which the agent will send traps. |
| 1.3.6.1.4.1.179.2.5.1.9.1 | RowskGeTrapDestEntry | not-accessible | mandatory | Entry of trap destination table. |
| 1.3.6.1.4.1.179.2.5.1.9.1.1 | ColumnskGeTrapDestIndex | read-only | mandatory | Index of the trap destination table. |
| 1.3.6.1.4.1.179.2.5.1.9.1.2 | ColumnskGeTrapDestAddress | read-only | mandatory | The destination address to which the agent sends its trap PDUs. |
| 1.3.6.1.4.1.179.2.5.1.10 | ScalarskGeTrapFilter | read-write | mandatory | The trap filter bits are stored as a sum of powers of 2 (a bit string) in this variable. If the bit is set to 0 the corresponding trap will not be transmitted.… |
| 1.3.6.1.4.1.179.2.5.1.13 | ScalarskGeSensorEntriesNumber | read-only | mandatory | Number of entries in skGeSensorTable. |
| 1.3.6.1.4.1.179.2.5.1.14 | TableskGeSensorTable | not-accessible | mandatory | Table for sensor related values. |
| 1.3.6.1.4.1.179.2.5.1.14.1 | RowskGeSensorEntry | not-accessible | mandatory | Entry of sensor table. |
| 1.3.6.1.4.1.179.2.5.1.14.1.1 | ColumnskGeSensorGeIndex | read-only | mandatory | Adapter index which corresponds with skGeIndex. |
| 1.3.6.1.4.1.179.2.5.1.14.1.2 | ColumnskGeSensorIndex | read-only | mandatory | Index of the sensor. The indexes have fixed semantics. |
| 1.3.6.1.4.1.179.2.5.1.14.1.3 | ColumnskGeSensorDescr | read-only | mandatory | A textual description of the sensor. |
| 1.3.6.1.4.1.179.2.5.1.14.1.4 | ColumnskGeSensorType | read-only | mandatory | Stores the sensor type. |
| 1.3.6.1.4.1.179.2.5.1.14.1.5 | ColumnskGeSensorValue | read-only | mandatory | Stores the current value of the sensor in 10th of degree celsius, milli volts or round per minutes (rpm). |
| 1.3.6.1.4.1.179.2.5.1.14.1.6 | ColumnskGeSensorWarningThresholdLow | read-only | mandatory | Stores the lower warning threshold of the allowed value range for the monitored unit. |
| 1.3.6.1.4.1.179.2.5.1.14.1.7 | ColumnskGeSensorWarningThresholdHigh | read-only | mandatory | Stores the upper warning threshold of the allowed value range for the monitored unit. |
| 1.3.6.1.4.1.179.2.5.1.14.1.8 | ColumnskGeSensorErrorThresholdLow | read-only | mandatory | Stores the lower threshold of the allowed value range for the monitored unit. |
| 1.3.6.1.4.1.179.2.5.1.14.1.9 | ColumnskGeSensorErrorThresholdHigh | read-only | mandatory | Stores the upper threshold of the allowed value range for the monitored unit. |
| 1.3.6.1.4.1.179.2.5.1.14.1.10 | ColumnskGeSensorStatus | read-only | mandatory | If a threshold is exceeded this flag will be set. |
| 1.3.6.1.4.1.179.2.5.1.14.1.11 | ColumnskGeSensorWarningCts | read-only | mandatory | If a warning threshold is exceeded this counter will be incremented and a trap will be generated. If the sensor value exceeds the threshold permanently this co… |
| 1.3.6.1.4.1.179.2.5.1.14.1.12 | ColumnskGeSensorErrorCts | read-only | mandatory | If a threshold is exceeded this counter will be incremented and a trap will be generated. If the sensor value exceeds the threshold permanently this counter is… |
| 1.3.6.1.4.1.179.2.5.1.14.1.13 | ColumnskGeSensorWarningTimeStamp | read-only | mandatory | Stores the time since the last reboot in hundreds of seconds of the last warning threshold exceed. |
| 1.3.6.1.4.1.179.2.5.1.14.1.14 | ColumnskGeSensorErrorTimeStamp | read-only | mandatory | Stores the time since the last reboot in hundreds of seconds of the last error threshold exceed. |
| 1.3.6.1.4.1.179.2.5.1.15 | ScalarskGeStatEntriesNumber | read-only | mandatory | Number of entries in the skGeStatTable. |
| 1.3.6.1.4.1.179.2.5.1.16 | TableskGeStatTable | not-accessible | mandatory | Statistical data of the ports. The number of table entries is stored in skGeStatEntriesNumber. |
| 1.3.6.1.4.1.179.2.5.1.16.1 | RowskGeStatEntry | not-accessible | mandatory | The first entry (skGeStatIndex) of each adapter card (skGeStatGeIndex) is a virtual one and represents the currently active port with settled statistical data.… |
| 1.3.6.1.4.1.179.2.5.1.16.1.1 | ColumnskGeStatGeIndex | read-only | mandatory | Adapter index which corresponds with skGeIndex. |
| 1.3.6.1.4.1.179.2.5.1.16.1.2 | ColumnskGeStatIndex | read-only | mandatory | The port index. The first index denotes the virtual port entry, which contains settled statistical data. The ports are enumerated from 1..n. |
| 1.3.6.1.4.1.179.2.5.1.16.1.3 | ColumnskGeStatTxOkCts | read-only | mandatory | A count of frames (including short frames, broadcasts frames, and multicast frames) that are successfully transmitted. |
| 1.3.6.1.4.1.179.2.5.1.16.1.4 | ColumnskGeStatTxOctetsHighOkCts | read-only | mandatory | The upper 32 bit count of data and padding octets of frames that are successfully transmitted. |
| 1.3.6.1.4.1.179.2.5.1.16.1.5 | ColumnskGeStatTxOctetsLowOkCts | read-only | mandatory | The lower 32 bit count of data and padding octets of frames that are successfully transmitted. |
| 1.3.6.1.4.1.179.2.5.1.16.1.6 | ColumnskGeStatTxBroadcastOkCts | read-only | mandatory | A count of frames that were successfully transmitted to the broadcast address. Frames transmitted to multicast addresses are not broadcast frames and are exclu… |
| 1.3.6.1.4.1.179.2.5.1.16.1.7 | ColumnskGeStatTxMulticastOkCts | read-only | mandatory | A count of frames that were successfully transmitted to a group destination address other than broadcast. |
| 1.3.6.1.4.1.179.2.5.1.16.1.8 | ColumnskGeStatTxUnicastOkCts | read-only | mandatory | The total number of frames transmitted that were directed to an unicast address. This number does not include frames directed to broadcast or multicast address… |
| 1.3.6.1.4.1.179.2.5.1.16.1.9 | ColumnskGeStatTxLongFramesCts | read-only | mandatory | The total number of frames transmitted that are more than the IEEE 802.3 maximum frame size. Typically, 1518 octets if neither the OneLevelVLAN nor TwoLevelVLA… |
| 1.3.6.1.4.1.179.2.5.1.16.1.10 | ColumnskGeStatTxBurstCts | read-only | mandatory | The total number of burst events. |
| 1.3.6.1.4.1.179.2.5.1.16.1.11 | ColumnskGeStatTxPFlowCtrlCts | read-only | mandatory | The total number of Pause Flow-Control frames transmitted, of Opcode=0001. |
| 1.3.6.1.4.1.179.2.5.1.16.1.12 | ColumnskGeStatTxFlowCtrlCts | read-only | mandatory | A count of Flow Control frames transmitted. |
| 1.3.6.1.4.1.179.2.5.1.16.1.13 | ColumnskGeStatTxSingleCollisionsCts | read-only | mandatory | A count of successfully transmitted frames for which transmission is inhibited by exactly one collision. |
| 1.3.6.1.4.1.179.2.5.1.16.1.14 | ColumnskGeStatTxMultipleCollisionsCts | read-only | mandatory | A count of successfully transmitted frames for which transmission is inhibited by more than one collision. |
| 1.3.6.1.4.1.179.2.5.1.16.1.15 | ColumnskGeStatTxExcessiveCollisionsCts | read-only | mandatory | A count of frames that due to excessive collisions are not transmitted successfully. |
| 1.3.6.1.4.1.179.2.5.1.16.1.16 | ColumnskGeStatTxLateCollisionsCts | read-only | mandatory | A count of the times that a collision has been detected later than one slot time, from the start of the packet transmission. A late collision is counted twice,… |
| 1.3.6.1.4.1.179.2.5.1.16.1.17 | ColumnskGeStatTxDeferralCts | read-only | mandatory | A count of frames whose transmission was delayed on its first attempt because the medium was busy. |
| 1.3.6.1.4.1.179.2.5.1.16.1.18 | ColumnskGeStatTxExcessiveDeferralCts | read-only | mandatory | A count of frames that deferred for an excessive period of time. This counter may only be incremented once per LLC transmission. |
| 1.3.6.1.4.1.179.2.5.1.16.1.19 | ColumnskGeStatTxFifoUnderrunCts | read-only | mandatory | The number of transmit FIFO underrun events. |
| 1.3.6.1.4.1.179.2.5.1.16.1.20 | ColumnskGeStatTxCarrierSenseCts | read-only | mandatory | A count of times that the carrier sense condition was not asserted or was deasserted during the transmission of a frame without collision. |
| 1.3.6.1.4.1.179.2.5.1.16.1.22 | ColumnskGeStatTxOctets64Cts | read-only | mandatory | The total number of frames transmitted that were 64 octets in length (excluding framing bits but including FCS octets). |
| 1.3.6.1.4.1.179.2.5.1.16.1.23 | ColumnskGeStatTxOctets127Cts | read-only | mandatory | The total number of frames transmitted that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets). |
| 1.3.6.1.4.1.179.2.5.1.16.1.24 | ColumnskGeStatTxOctets255Cts | read-only | mandatory | The total number of frames transmitted that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets). |
| 1.3.6.1.4.1.179.2.5.1.16.1.25 | ColumnskGeStatTxOctets511Cts | read-only | mandatory | The total number of frames transmitted that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets). |
| 1.3.6.1.4.1.179.2.5.1.16.1.26 | ColumnskGeStatTxOctets1023Cts | read-only | mandatory | The total number of frames transmitted that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets). |
| 1.3.6.1.4.1.179.2.5.1.16.1.27 | ColumnskGeStatTxOctetsMaxCts | read-only | mandatory | The total number of frames transmitted that were between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets). If the One… |
| 1.3.6.1.4.1.179.2.5.1.16.1.28 | ColumnskGeStatTxSyncCts | read-only | mandatory | The total number of frames transmitted synchronuously. |
| 1.3.6.1.4.1.179.2.5.1.16.1.29 | ColumnskGeStatTxSyncOctetsHighCts | read-only | mandatory | The upper 32 bit count of synchronuously transmitted octets. |
| 1.3.6.1.4.1.179.2.5.1.16.1.30 | ColumnskGeStatTxSyncOctetsLowCts | read-only | mandatory | The lower 32 bit count of synchronuously transmitted octets. |
| 1.3.6.1.4.1.179.2.5.1.16.1.31 | ColumnskGeStatRxOkCts | read-only | mandatory | A count of frames (including short frames, broadcast frames, and multicast frames) that are successfully received. |
| 1.3.6.1.4.1.179.2.5.1.16.1.32 | ColumnskGeStatRxOctetsHighOkCts | read-only | mandatory | The upper 32 bit count of data and padding octets in frames that are successfully received. This does not include octets in frames received with frame-too-long… |
| 1.3.6.1.4.1.179.2.5.1.16.1.33 | ColumnskGeStatRxOctetsLowOkCts | read-only | mandatory | The lower 32 bit count of data and padding octets in frames that are successfully received. This does not include octets in frames received with frame-too-long… |
| 1.3.6.1.4.1.179.2.5.1.16.1.34 | ColumnskGeStatRxBroadcastOkCts | read-only | mandatory | A count of frames that are successfully received and are directed to the broadcast group address. This does not include frames received with frame-too-long, FC… |
| 1.3.6.1.4.1.179.2.5.1.16.1.35 | ColumnskGeStatRxMulticastOkCts | read-only | mandatory | A count of frames that are successfully received and are directed to an active non-broadcast group address. This does not include frames received with frame-to… |
| 1.3.6.1.4.1.179.2.5.1.16.1.36 | ColumnskGeStatRxUnicastOkCts | read-only | mandatory | The total number of good frames received that were directed to any unicast address, as defined by the Counter Exact Address Match Criteria. |
| 1.3.6.1.4.1.179.2.5.1.16.1.37 | ColumnskGeStatRxPFlowCtrlCts | read-only | mandatory | A count of Flow Control frames received with a length- or-type field value equal to the reserved type for 802.3_MAC_Control and an opcode indicating a PAUSE op… |
| 1.3.6.1.4.1.179.2.5.1.16.1.38 | ColumnskGeStatRxFlowCtrlCts | read-only | mandatory | A count of Flow Control frames received. Flow Control frames are defined as valid frames with a length-or-type field value equal to the reserved type for 802.3… |
| 1.3.6.1.4.1.179.2.5.1.16.1.39 | ColumnskGeStatRxPFlowCtrlErrCts | read-only | mandatory | A count of Flow Control frames received with standard PAUSE address with a length-or-type field value equal to the reserved type for 802.3_MAC_Control, but wit… |
| 1.3.6.1.4.1.179.2.5.1.16.1.40 | ColumnskGeStatRxFlowCtrlUnknownCts | read-only | mandatory | A count of Flow Control frames received that contain an opcode that is not supported by the device. Flow Control frames are defined as valid frames with a leng… |
| 1.3.6.1.4.1.179.2.5.1.16.1.41 | ColumnskGeStatRxBurstCts | read-only | mandatory | The total number of burst events. |
| 1.3.6.1.4.1.179.2.5.1.16.1.42 | ColumnskGeStatRxMissedCts | read-only | mandatory | The total number of events in which frames were missed by the controller due to buffer overflow. |
| 1.3.6.1.4.1.179.2.5.1.16.1.43 | ColumnskGeStatRxFramingCts | read-only | mandatory | The total number of frames received with improper end- of-frame delimiter |
| 1.3.6.1.4.1.179.2.5.1.16.1.44 | ColumnskGeStatRxFifoOverflowCts | read-only | mandatory | The number of receive FIFO overflow events. |
| 1.3.6.1.4.1.179.2.5.1.16.1.45 | ColumnskGeStatRxJabberCts | read-only | mandatory | The total number of frames received that were longer than 1518 octets (excluding framing bits but including FCS octets), and had a bad FCS with an integral num… |
| 1.3.6.1.4.1.179.2.5.1.16.1.46 | ColumnskGeStatRxCarrierCts | read-only | mandatory | An event counter for the number of times the carrier event is longer than the permissible duration. |
| 1.3.6.1.4.1.179.2.5.1.16.1.47 | ColumnskGeStatRxIRLengthCts | read-only | mandatory | A count of frames with a length-or-type field value between the minimum unpadded LLC MAC client data size and the maximum allowed LLC MAC client data size incl… |
| 1.3.6.1.4.1.179.2.5.1.16.1.48 | ColumnskGeStatRxSymbolCts | read-only | mandatory | A count of the number of times the receiving media is non-idle (a carrier event) for a period of time greater than or equal to slot-time for half-duplex operat… |
| 1.3.6.1.4.1.179.2.5.1.16.1.49 | ColumnskGeStatRxShortsCts | read-only | mandatory | An event counter by one for each carrier event with activity-duration less than short-event-max-time. In the 1000 Mb/s case short-event-max-time is 72 bits (9 … |
| 1.3.6.1.4.1.179.2.5.1.16.1.50 | ColumnskGeStatRxRuntCts | read-only | mandatory | A counter for each carrier-event that the octet count is less than 64. |
| 1.3.6.1.4.1.179.2.5.1.16.1.51 | ColumnskGeStatRxCextCts | read-only | mandatory | A counter of received frames with no collision, short, or framing error in which the carrier extension was inadequate. |
| 1.3.6.1.4.1.179.2.5.1.16.1.52 | ColumnskGeStatRxTooLongCts | read-only | mandatory | A count of frames received that exceed the maximum permitted frame size, i.e., 1518 octets (excluding framing bits, but including FCS octets) and were otherwis… |
| 1.3.6.1.4.1.179.2.5.1.16.1.53 | ColumnskGeStatRxFCSCts | read-only | mandatory | A count of received frames that are an integral number of octets in length and do not pass the FCS check. This does not include frames received with frame-too-… |
| 1.3.6.1.4.1.179.2.5.1.16.1.55 | ColumnskGeStatRxOctets64Cts | read-only | mandatory | The total number of frames (including bad frames) received that were 64 octets in length (excluding framing bits, but including FCS octets). |
| 1.3.6.1.4.1.179.2.5.1.16.1.56 | ColumnskGeStatRxOctets127Cts | read-only | mandatory | The total number of frames (including bad frames) received that were between 65 and 127 octets in length inclusive (excluding framing bits, but including FCS o… |
| 1.3.6.1.4.1.179.2.5.1.16.1.57 | ColumnskGeStatRxOctets255Cts | read-only | mandatory | The total number of frames (including bad frames) received that were between 128 and 255 octets in length inclusive (excluding framing bits, but including FCS … |
| 1.3.6.1.4.1.179.2.5.1.16.1.58 | ColumnskGeStatRxOctets511Cts | read-only | mandatory | The total number of frames (including bad frames) received that were between 256 and 511 octets in length inclusive (excluding framing bits, but including FCS … |
| 1.3.6.1.4.1.179.2.5.1.16.1.59 | ColumnskGeStatRxOctets1023Cts | read-only | mandatory | The total number of frames (including bad frames) received that were between 512 and 1023 octets in length inclusive (excluding framing bits, but including FCS… |
| 1.3.6.1.4.1.179.2.5.1.16.1.60 | ColumnskGeStatRxOctetsMaxCts | read-only | mandatory | The total number of frames (including bad frames) received that were between 1024 and 1518 octets in length inclusive (excluding framing bits, but including FC… |
| 1.3.6.1.4.1.179.2.5.1.16.1.61 | ColumnskGeStatRxLongFramesCts | read-only | mandatory | The total number of frames received that are greater than the IEEE 802.3 maximum frame size. Typically, 1518 octets if neither the OneLevelVLAN nor TwoLevelVLA… |
| 1.3.6.1.4.1.179.2.5.1.17 | ScalarskGeConfEntriesNumber | read-only | mandatory | The number of entries in the skGeConfTable. |
| 1.3.6.1.4.1.179.2.5.1.18 | TableskGeConfTable | not-accessible | mandatory | The table describes the physical port data. The number of table entries is stored in skGeConfEntriesNumber. |
| 1.3.6.1.4.1.179.2.5.1.18.1 | RowskGeConfEntry | not-accessible | mandatory | The first entry (skGeConfIndex) of each adapter card (skGeConfGeIndex) is a virtual one and represents the active MAC instance with settled statistical data. T… |
| 1.3.6.1.4.1.179.2.5.1.18.1.1 | ColumnskGeConfGeIndex | read-only | mandatory | Adapter index which corresponds with skGeIndex. |
| 1.3.6.1.4.1.179.2.5.1.18.1.2 | ColumnskGeConfIndex | read-only | mandatory | The port index. The value is equivalent to skGeStatPortIndex. The ports are enumerated from 1..n. The first entry is the virtual one. |
| 1.3.6.1.4.1.179.2.5.1.18.1.3 | ColumnskGeConfPhysCurrentAddr | read-only | mandatory | The physical address. The first entry of a adapter stores the physical address reported to the operating system. The other entries store the physical addresses… |
| 1.3.6.1.4.1.179.2.5.1.18.1.4 | ColumnskGeConfPhysFactoryAddr | read-only | mandatory | The burned in physical address. The first entry of a adapter stores the physical address reported to the operating system. The other entries store the physical… |
| 1.3.6.1.4.1.179.2.5.1.18.1.5 | ColumnskGeConfPMDType | read-only | mandatory | Stores the physical media type of the port. |
| 1.3.6.1.4.1.179.2.5.1.18.1.6 | ColumnskGeConfConnector | read-only | mandatory | Stores the connector type of the port. |
| 1.3.6.1.4.1.179.2.5.1.18.1.7 | ColumnskGeConfLinkCap | read-only | mandatory | Indicates which connection modes the port supports. The modes are stored as a sum of powers of 2. Mode Power 0 half-duplex 1 full-duplex 2 auto-half-duplex 3 a… |
| 1.3.6.1.4.1.179.2.5.1.18.1.8 | ColumnskGeConfLinkMode | read-write | mandatory | Defines in which mode the port should work. The modes half-duplex and full-duplex force the port to work in the corresponding mode. No autonegotiation is perfo… |
| 1.3.6.1.4.1.179.2.5.1.18.1.9 | ColumnskGeConfLinkModeStatus | read-only | mandatory | Stores the mode with which the port is currently working. The keyword auto indicates that the link mode was established by autonegotiation. Otherwise the port … |
| 1.3.6.1.4.1.179.2.5.1.18.1.10 | ColumnskGeConfLinkStatus | read-only | mandatory | Stores the link status of the unit. If a link becomes up or down a trap is generated. |
| 1.3.6.1.4.1.179.2.5.1.18.1.11 | ColumnskGeConfFlowCtrlCap | read-only | mandatory | Indicates which flow control types the port supports. |
| 1.3.6.1.4.1.179.2.5.1.18.1.12 | ColumnskGeConfFlowCtrlMode | read-write | mandatory | Defines the flow-control type the port should announce during auto-negotiation. If auto-negotiation is disabled flow-control is disabled and settings to this v… |
| 1.3.6.1.4.1.179.2.5.1.18.1.13 | ColumnskGeConfFlowCtrlStatus | read-only | mandatory | Stores the flow-control type the port is currently using. |
| 1.3.6.1.4.1.179.2.5.1.18.1.14 | ColumnskGeConfPhyOperationCap | read-only | mandatory | Indicates which operation modes the phy supports. The modes are stored as a sum of powers of 2. Mode Power 0 master-slave auto-negotiation 1 master 2 slave |
| 1.3.6.1.4.1.179.2.5.1.18.1.15 | ColumnskGeConfPhyOperationMode | read-write | mandatory | Defines in which mode the phy should work. The modes master and slave force the port to work in the corresponding mode. No autonegotiation is performed. The au… |
| 1.3.6.1.4.1.179.2.5.1.18.1.16 | ColumnskGeConfPhyOperationStatus | read-only | mandatory | Stores the operation mode with which the port is currently working. |
| 1.3.6.1.4.1.179.2.5.2 | NodeskGeVpd | |||
| 1.3.6.1.4.1.179.2.5.2.1 | TableskGeVpdTable | not-accessible | mandatory | This table stores data for easy vpd access. |
| 1.3.6.1.4.1.179.2.5.2.1.1 | RowskGeVpdEntry | not-accessible | mandatory | Entry of skGeVpdTable. |
| 1.3.6.1.4.1.179.2.5.2.1.1.1 | ColumnskGeVpdIndex | read-only | mandatory | Adapter index that corresponds to skGeIndex. |
| 1.3.6.1.4.1.179.2.5.2.1.1.2 | ColumnskGeVpdFreeBytes | read-only | mandatory | Stores the number of free bytes in the read-write area of the VPD RAM. |
| 1.3.6.1.4.1.179.2.5.2.1.1.3 | ColumnskGeVpdEntryList | read-only | mandatory | Stores a list of the VPD keywords. The elements of the list are separated by a space character (0x20). |
| 1.3.6.1.4.1.179.2.5.2.2 | TableskGeVpdValueTable | not-accessible | mandatory | This table provides access to the Vital Product Data (VPD). |
| 1.3.6.1.4.1.179.2.5.2.2.1 | RowskGeVpdValueEntry | not-accessible | mandatory | VPD value table entry. On creation of a new entry: If the key is first set the vpd subsystem will create a new entry with an empty value field. If the value is… |
| 1.3.6.1.4.1.179.2.5.2.2.1.1 | ColumnskGeVpdValueIndex | read-only | mandatory | Adapter index that corresponds to skGeIndex. |
| 1.3.6.1.4.1.179.2.5.2.2.1.2 | ColumnskGeVpdKey | read-write | mandatory | VPD keyword. |
| 1.3.6.1.4.1.179.2.5.2.2.1.3 | ColumnskGeVpdValue | read-write | mandatory | Value stored under VPD keyword. |
| 1.3.6.1.4.1.179.2.5.2.2.1.4 | ColumnskGeVpdAccess | read-only | mandatory | Defines whether the entry is only readable or also writable. Read-only entries cannot be changed or deleted. |
| 1.3.6.1.4.1.179.2.5.2.2.1.5 | ColumnskGeVpdValid | read-write | mandatory | If the entry is writeable a set to 'invalid' will remove the entry from the VPD. A set to 'valid' will have no effect. |
| 1.3.6.1.4.1.179.2.5.3 | NodeskGeRlmt | |||
| 1.3.6.1.4.1.179.2.5.3.1 | ScalarskGeRlmtEntriesNumber | read-only | mandatory | Stores the number of skGeRlmtTable entries. The number corresponds to skGeNumber. |
| 1.3.6.1.4.1.179.2.5.3.2 | TableskGeRlmtTable | not-accessible | mandatory | Table for RLMT (Redundant Link ManagemenT) specific data. |
| 1.3.6.1.4.1.179.2.5.3.2.1 | RowskGeRlmtEntry | not-accessible | mandatory | Entry of skGeRlmtTable. |
| 1.3.6.1.4.1.179.2.5.3.2.1.1 | ColumnskGeRlmtIndex | read-only | mandatory | Stores the index of the adapter card that corresponds with this entry. It is identical to skGeIndex. |
| 1.3.6.1.4.1.179.2.5.3.2.1.2 | ColumnskGeRlmtMode | read-write | mandatory | Stores the working mode of RLMT as a power of 2. Mode Power link-check 0 Always active send-check 1 Sends hello packets spanning-tree 2 Monitors SP packets mon… |
| 1.3.6.1.4.1.179.2.5.3.2.1.3 | ColumnskGeRlmtPortActive | read-only | mandatory | Stores the index of the currently active port. The value 0 indicates that currently no port is active. |
| 1.3.6.1.4.1.179.2.5.3.2.1.4 | ColumnskGeRlmtPortPreferred | read-write | mandatory | If RLMT evaluates that all links are well working this value is used to decide which port should be used. The value ?0? indicates automatic mode and let RLMT d… |
| 1.3.6.1.4.1.179.2.5.3.2.1.5 | ColumnskGeRlmtChangeCts | read-only | mandatory | Counts the number of times RLMT switched from one port to another which indicates an error. |
| 1.3.6.1.4.1.179.2.5.3.2.1.6 | ColumnskGeRlmtChangeTimeStamp | read-only | mandatory | Stores the time in hundreds of seconds since the last reboot when the connection was switched to another port. |
| 1.3.6.1.4.1.179.2.5.3.2.1.7 | ColumnskGeRlmtChangeEstimate | read-only | mandatory | Stores the number of port switches per hour. |
| 1.3.6.1.4.1.179.2.5.3.2.1.8 | ColumnskGeRlmtChangeThreshold | read-write | mandatory | Stores the threshold in number of port switches per hour. If the threshold is exceeded a trap is generated. |
| 1.3.6.1.4.1.179.2.5.3.2.1.9 | ColumnskGeRlmtPortNumber | read-only | mandatory | Stores the number of physically present ports. |
| 1.3.6.1.4.1.179.2.5.3.3 | ScalarskGeRlmtStatEntriesNumber | read-only | mandatory | Number of table elements in skGeRlmtStatTable. |
| 1.3.6.1.4.1.179.2.5.3.4 | TableskGeRlmtStatTable | not-accessible | mandatory | Stores RLMT specific statistical data according to each port. |
| 1.3.6.1.4.1.179.2.5.3.4.1 | RowskGeRlmtStatEntry | not-accessible | mandatory | Entry of RLMT statistic table. |
| 1.3.6.1.4.1.179.2.5.3.4.1.1 | ColumnskGeRlmtStatGeIndex | read-only | mandatory | Index of the adapter card. |
| 1.3.6.1.4.1.179.2.5.3.4.1.2 | ColumnskGeRlmtStatIndex | read-only | mandatory | Index of the physical port. |
| 1.3.6.1.4.1.179.2.5.3.4.1.3 | ColumnskGeRlmtStatStatus | read-only | mandatory | The working state of the port. |
| 1.3.6.1.4.1.179.2.5.3.4.1.4 | ColumnskGeRlmtStatTxHelloCts | read-only | mandatory | Number of hello packets sent in the send-check mode. |
| 1.3.6.1.4.1.179.2.5.3.4.1.5 | ColumnskGeRlmtStatRxHelloCts | read-only | mandatory | Number of hello packets received in the send-check mode. |
| 1.3.6.1.4.1.179.2.5.3.4.1.6 | ColumnskGeRlmtStatTxSpHelloReqCts | read-only | mandatory | Number of transmitted packets in spanning-tree mode to force a spanning-tree hello packet. |
| 1.3.6.1.4.1.179.2.5.3.4.1.7 | ColumnskGeRlmtStatRxSpHelloCts | read-only | mandatory | Number of the received spanning-tree hello packets in the spanning-tree mode. |
| 1.3.6.1.4.1.179.2.5.3.5 | ScalarskGeRlmtMonitorEntriesNumber | read-only | mandatory | Number of stations monitored by RLMT. |
| 1.3.6.1.4.1.179.2.5.3.6 | TableskGeRlmtMonitorTable | not-accessible | mandatory | Table of stations to be monitored by RLMT. |
| 1.3.6.1.4.1.179.2.5.3.6.1 | RowskGeRlmtMonitorEntry | not-accessible | mandatory | Entry of skGeRlmtMonitorTable. |
| 1.3.6.1.4.1.179.2.5.3.6.1.1 | ColumnskGeRlmtMonitorGeIndex | read-only | mandatory | Index of the adapter card. |
| 1.3.6.1.4.1.179.2.5.3.6.1.2 | ColumnskGeRlmtMonitorIndex | read-only | mandatory | Index of the address table entry. |
| 1.3.6.1.4.1.179.2.5.3.6.1.3 | ColumnskGeRlmtMonitorAddr | read-write | mandatory | Physical address of a monitored station. |
| 1.3.6.1.4.1.179.2.5.3.6.1.4 | ColumnskGeRlmtMonitorErrCts | read-only | mandatory | Counts the number of times the redundant link of the monitored station got lost. |
| 1.3.6.1.4.1.179.2.5.3.6.1.5 | ColumnskGeRlmtMonitorErrTimeStamp | read-only | mandatory | Stores the timestamp of the last time the link got lost. |
| 1.3.6.1.4.1.179.2.5.3.6.1.6 | ColumnskGeRlmtMonitorAdmin | read-write | mandatory | Set to disable stops the monitoring of the remote station. |
| 1.3.6.1.4.1.179.3 | NodeskNICs | |||
| 1.3.6.1.4.1.179.3.1 | NodeskFddiNICs | |||
| 1.3.6.1.4.1.179.3.2 | NodeskGeNICs | |||
| 1.3.6.1.4.1.179.3.2.1 | NodeskGeSxSingleLink | |||
| 1.3.6.1.4.1.179.3.2.2 | NodeskGeSxDualLink | |||
| 1.3.6.1.4.1.179.3.2.3 | NodeskGeLxSingleLink | |||
| 1.3.6.1.4.1.179.3.2.4 | NodeskGeLxDualLink | |||
| 1.3.6.1.4.1.179.3.2.5 | NodeskGeCxSingleLink | |||
| 1.3.6.1.4.1.179.3.2.6 | NodeskGeCxDualLink | |||
| 1.3.6.1.4.1.179.3.2.7 | NodeskGeTxSingleLink | |||
| 1.3.6.1.4.1.179.3.2.8 | NodeskGeTxDualLink | |||
| 1.3.6.1.4.1.179.4 | NodeskChipSets | |||
| 1.3.6.1.4.1.179.4.1 | NodeskGeXMAC11800FP | |||
| 1.3.6.1.4.1.179.500 | NodeskGeSensorWarningLower | This trap is generated when one of the adapter sensor values exceeds the lower warning threshold. | ||
| 1.3.6.1.4.1.179.501 | NodeskGeSensorWarningUpper | This trap is generated when one of the adapter sensor values exceeds the upper warning threshold. | ||
| 1.3.6.1.4.1.179.502 | NodeskGeSensorErrorLower | This trap is generated when one of the adapter sensor values exceeds the lower error threshold. | ||
| 1.3.6.1.4.1.179.503 | NodeskGeSensorErrorUpper | This trap is generated when one of the adapter sensor values exceeds the upper error threshold. | ||
| 1.3.6.1.4.1.179.520 | NodeskGeRlmtChangeThresholdCondition | This trap is generated when the port switches exceeded the threshold. | ||
| 1.3.6.1.4.1.179.521 | NodeskGeRlmtChangeCondition | This trap is generated when the connection is switched to another port. The with the trap passed variables correspond to the new active port. | ||
| 1.3.6.1.4.1.179.522 | NodeskGeRlmtPortDown | This trap is generated when RLMT detects that a port went logically down. | ||
| 1.3.6.1.4.1.179.523 | NodeskGeRlmtPortUp | This trap is generated when RLMT detects that a port went logically up. | ||
| 1.3.6.1.4.1.179.524 | NodeskGeRlmtSegmentation | This trap is generated when RLMT works in spanning-tree mode (skGeRlmtMode) and two root bridges are detected, which means a segmentation of net. One of the se… |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| SkGeMACAddress | OCTET STRING (SIZE (6)) |