SL-SONET-APS-MIB
29 objects
This MIB module describes the SiteLight SONET APS.
Imported Objects
| IF-MIB | InterfaceIndex |
| PerfHist-TC-MIB | PerfCurrentCount PerfIntervalCount PerfTotalCount |
| SL-SONET-MIB | slSonetMib |
| SNMPv2-CONF | MODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP |
| SNMPv2-SMI | Counter32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | DisplayString RowStatus TruthValue |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.4515.1.6.5 | IdentityslSonetApsMib | This MIB module describes the SiteLight SONET APS. | ||
| 1.3.6.1.4.1.4515.1.6.5.1 | NodeslSonetApsConfig | |||
| 1.3.6.1.4.1.4515.1.6.5.1.1 | TableslSonetApsConfigTable | not-accessible | current | This table contains objects to configure APS (Automatic Protection Switching) feature in a SONET Line. APS is the ability to configure a pair of SONET lines fo… |
| 1.3.6.1.4.1.4515.1.6.5.1.1.1 | RowslSonetApsConfigEntry | not-accessible | current | An entry is created during startup if the SEEP specifies that there are two trunk ports. The value of slSonetApsEnable determines if the APS is configured or n… |
| 1.3.6.1.4.1.4515.1.6.5.1.1.1.1 | ColumnslSonetApsWorkingIndex | read-only | current | When a pair of APS lines is configured, one line has to be the working line, which is the primary line, and the other has to be the protection line, which is t… |
| 1.3.6.1.4.1.4515.1.6.5.1.1.1.2 | ColumnslSonetApsProtectionIndex | read-create | current | The protection line indicates that it will become the active line when an APS switch occurs (APS switch could occur because of a failure on the working line). |
| 1.3.6.1.4.1.4515.1.6.5.1.1.1.3 | ColumnslSonetApsEnable | read-create | current | This object is used to enable or disable the APS feature on the working/protection line pairs. |
| 1.3.6.1.4.1.4515.1.6.5.1.1.1.4 | ColumnslSonetApsArchMode | read-create | current | This object is used to configure APS architecture mode on the working/protection line pairs (read-write). All of the following are supported on single slot. on… |
| 1.3.6.1.4.1.4515.1.6.5.1.1.1.5 | ColumnslSonetApsActiveLineRx | read-only | current | This object indicates which Rx line is currently active. It could be the working line, the protection line or none if neither working nor protection line is ac… |
| 1.3.6.1.4.1.4515.1.6.5.1.1.1.6 | ColumnslSonetApsActiveLineTx | read-only | current | This object indicates which Tx line is currently active. It could be the working line, the protection line or none if neither working nor protection line is ac… |
| 1.3.6.1.4.1.4515.1.6.5.1.1.1.7 | ColumnslSonetApsWaitToRestore | read-create | current | This object contains interval in minutes to wait before attempting to switch back to working line. Not applicable if the line is configured in non-revertive mo… |
| 1.3.6.1.4.1.4515.1.6.5.1.1.1.8 | ColumnslSonetApsDirection | read-create | current | This object is used to configure the switching direction which this APS line supports (read-write). Unidirectional : APS switch only in one direction. Bidirect… |
| 1.3.6.1.4.1.4515.1.6.5.1.1.1.9 | ColumnslSonetApsRevertive | read-create | current | This object is used to configure the APS revertive or nonrevertive option (read-write). revertive : Will switch the working line back to active state after the… |
| 1.3.6.1.4.1.4515.1.6.5.1.1.1.10 | ColumnslSonetApsDirectionOperational | read-only | current | This object shows the actual APS direction that is implemented on the Near End terminal. APS direction configured through slSonetApsDirection is negotiated wit… |
| 1.3.6.1.4.1.4515.1.6.5.1.1.1.11 | ColumnslSonetApsArchModeOperational | read-only | current | This object shows the actual APS architecture mode that is implemented on the Near End terminal. APS architecture mode configured through slSonetApsArchMode ob… |
| 1.3.6.1.4.1.4515.1.6.5.1.1.1.12 | ColumnslSonetApsChanStatus | read-only | current | Indicates the current state of the port. lockedOut This bit, when applied to a working channel, indicates that the channel is prevented from switching to the p… |
| 1.3.6.1.4.1.4515.1.6.5.1.1.1.13 | ColumnslSonetApsChanSignalDegrades | read-only | current | A count of Signal Degrade conditions. This condition occurs when the line Bit Error Rate exceeds the currently configured threshold. |
| 1.3.6.1.4.1.4515.1.6.5.1.1.1.14 | ColumnslSonetApsChanSignalFailures | read-only | current | A count of Signal Failure conditions that have been detected on the incoming signal. This condition occurs when a loss of signal, loss of frame, AIS-L or a Lin… |
| 1.3.6.1.4.1.4515.1.6.5.1.1.1.15 | ColumnslSonetApsChanLastSwitchover | read-only | current | The value of sysUpTime when this channel last completed a switch to the protection line. If this channel has never switched to the protection line, or this cha… |
| 1.3.6.1.4.1.4515.1.6.5.1.1.1.16 | ColumnslSonetApsLineFailureCodeStatus | read-only | current | The Sonet APS line failure code status - this is the status of failure encountered by the APS line. slSonetApsChannelMismatch: trasmitted K1 byte and received … |
| 1.3.6.1.4.1.4515.1.6.5.1.1.1.17 | ColumnslSonetApsConfigSwitchCommand | read-create | current | A switch command initiates one external request for evaluation (read-write). (1) Clear - Clears all switch commands on the channel. (2) Lockout Of Protection -… |
| 1.3.6.1.4.1.4515.1.6.5.1.1.1.18 | ColumnslSonetApsLineSwitchReason | read-only | current | The reason why APS switch happened. When the working line on one end fails, its other end is told to do an APS switch. The following options in the increasing … |
| 1.3.6.1.4.1.4515.1.6.5.1.1.1.19 | ColumnslSonetApsResetCounters | read-create | current | Setting this variable to 1 will cause the counters on all of the SONET APS Config Table to be initialized to zero (read-write). |
| 1.3.6.1.4.1.4515.1.6.5.1.1.1.20 | ColumnslSonetApsConfigActiveRequest | read-write | current | The Active Switch APS request: slSonetApsRevertive : Switch back to working line after the Wait-to-Restore interval is over, and failures are cleared. It is th… |
| 1.3.6.1.4.1.4515.1.6.5.1.1.1.21 | ColumnslSonetApsConfigExerciseResult | read-only | current | This variable contains the result of the last exercise command. True - means test success. False - otherwise. |
| 1.3.6.1.4.1.4515.1.6.5.2 | NodeslSonetApsTraps | |||
| 1.3.6.1.4.1.4515.1.6.5.2.1 | NotificationslSonetApsTrapSwitchover | current | An slSonetApsTrapSwitchover notification is sent when the value whenever a switchover occures. | |
| 1.3.6.1.4.1.4515.1.6.5.2.2 | NotificationslSonetApsTrapFailureCodeChanged | current | An slSonetApsTrapChannelMismatch notification is sent when the APS failure code status is changed. | |
| 1.3.6.1.4.1.4515.1.6.5.2.3 | NotificationslSonetApsTrapEnabled | current | An slSonetApsTrapSwitchover notification is sent when the value of slSonetApsEnable is changed. |