SNMP540-MGMT-MIB
58 objects
No module-level DESCRIPTION found.
Imported Objects
| DDS-MIB | dsu |
| RFC-1212 | OBJECT-TYPE |
| RFC1213-MIB | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.498.8.4 | Nodesnmp540 | |||
| 1.3.6.1.4.1.498.8.4.1 | Scalarsnmp540MIBversion | read-only | mandatory | Identifies the version of the MIB. The format of the version is x.yzT, where 'x' identifies the major revision number, 'y'identifies the minor revision number,… |
| 1.3.6.1.4.1.498.8.4.2 | Nodesnmp540Config | |||
| 1.3.6.1.4.1.498.8.4.2.1 | Scalarsnmp540ActivateCfg | read-write | mandatory | The Activate configuration object. The value noChange(1), will maintain the old dataset configuration without saving any changes. The value activateNewCfg(2), … |
| 1.3.6.1.4.1.498.8.4.2.2 | Scalarsnmp540DtePortType | read-write | mandatory | The value auto(3) indicates that the electrical portion of the DTE interface is automatically detected. The rs232(1) value forces the DTE port to EIA/TIA-232-E… |
| 1.3.6.1.4.1.498.8.4.2.3 | Nodesnmp540EiaTestControl | |||
| 1.3.6.1.4.1.498.8.4.2.3.1 | Scalarsnmp540EiaRlcontrol | read-write | mandatory | The RL Eia Test control lead option. This option either allows or blocks EIA initiated test inputs from the DTE interface. |
| 1.3.6.1.4.1.498.8.4.2.3.2 | Scalarsnmp540EiaLlcontrol | read-write | mandatory | The LL Eia Test control lead option. This option either allows or blocks EIA initiated test inputs from the DTE interface. |
| 1.3.6.1.4.1.498.8.4.2.3.3 | Scalarsnmp540EiaTmcontrol | read-write | mandatory | The Eia Test Mode lead option. This option controls the operation of the Test Mode output indication. A value of (1) allows the Test Mode output to indicate th… |
| 1.3.6.1.4.1.498.8.4.2.3.4 | Scalarsnmp540LlbDetect | read-write | mandatory | The Latching Loopback test detect option. This option controls the operation of the latching loopback detection. A value of (1) allows, the latching loopback t… |
| 1.3.6.1.4.1.498.8.4.3 | Nodesnmp540Control | |||
| 1.3.6.1.4.1.498.8.4.3.1 | Scalarsnmp540UnitReset | read-write | mandatory | The value reset(2) will cause the snmp540 to perform a cold start. As soon as the object has been set to reset(2), the snmp540 will begin its reinitialization.… |
| 1.3.6.1.4.1.498.8.4.4 | Nodesnmp540AlarmData | |||
| 1.3.6.1.4.1.498.8.4.4.1 | Nodesnmp540PowerUpAlm | |||
| 1.3.6.1.4.1.498.8.4.4.2 | Nodesnmp540CfgChkSumErrAlm | |||
| 1.3.6.1.4.1.498.8.4.4.3 | Nodesnmp540StcLoopbackAlm | |||
| 1.3.6.1.4.1.498.8.4.4.4 | Nodesnmp540NoNtwkLoopCurrentAlm | |||
| 1.3.6.1.4.1.498.8.4.4.5 | Nodesnmp540LinePairsReversedAlm | |||
| 1.3.6.1.4.1.498.8.4.4.6 | Nodesnmp540NoSignalAlm | |||
| 1.3.6.1.4.1.498.8.4.4.7 | Nodesnmp540FpTestAlm | |||
| 1.3.6.1.4.1.498.8.4.4.8 | Nodesnmp540DSRLossAlm | |||
| 1.3.6.1.4.1.498.8.4.4.9 | Nodesnmp540DTRLossAlm | |||
| 1.3.6.1.4.1.498.8.4.4.10 | Nodesnmp540DTPLossAlm | |||
| 1.3.6.1.4.1.498.8.4.4.11 | Nodesnmp540DCDLossAlm | |||
| 1.3.6.1.4.1.498.8.4.4.12 | Nodesnmp540RXDLossAlm | |||
| 1.3.6.1.4.1.498.8.4.4.13 | Nodesnmp540TXDLossAlm | |||
| 1.3.6.1.4.1.498.8.4.4.14 | Nodesnmp540JitterAlm | |||
| 1.3.6.1.4.1.498.8.4.4.15 | Nodesnmp540BpvAlm | |||
| 1.3.6.1.4.1.498.8.4.4.16 | Nodesnmp540FrameLossAlm | |||
| 1.3.6.1.4.1.498.8.4.4.17 | Nodesnmp540SignalToNoiseAlm | |||
| 1.3.6.1.4.1.498.8.4.4.18 | Nodesnmp540RxSignalLowAlm | |||
| 1.3.6.1.4.1.498.8.4.5 | Nodesnmp540AlarmCfgThr | |||
| 1.3.6.1.4.1.498.8.4.5.1 | Scalarsnmp540AlarmCfgCountWindow | read-write | mandatory | This is the DDS Alarm Threshold Interval. It specifies the amount of time, 1 to 15 minutes, in which the threshold setting is to be exceeded for the alarm to o… |
| 1.3.6.1.4.1.498.8.4.5.2 | Tablesnmp540AlarmCfgTable | not-accessible | mandatory | The GDC snmp540 Alarm Configuration Table. |
| 1.3.6.1.4.1.498.8.4.5.2.1 | Rowsnmp540AlarmCfgEntry | not-accessible | mandatory | An entry in the snmp540 alarm table. |
| 1.3.6.1.4.1.498.8.4.5.2.1.1 | Columnsnmp540AlarmCfgIdentifier | read-only | mandatory | The unique alarm identifier assigned to this alarm type. The format of this identifier is an OBJECT IDENTIFIER that has the following format: {iso(1) org(3) do… |
| 1.3.6.1.4.1.498.8.4.5.2.1.2 | Columnsnmp540AlarmCfgThreshold | read-write | mandatory | This function sets/reads the alarm threshold settings criteria. This threshold is used along with the alarm window to determine the number of instances in a gi… |
| 1.3.6.1.4.1.498.8.4.6 | Nodesnmp540LineStats | |||
| 1.3.6.1.4.1.498.8.4.6.1 | Scalarsnmp540LineStatsInterval | read-write | mandatory | The DDS Line Statistics Interval specifies the amount of LineStats data to be reported. Measurements are stored every minute and accumulated. The latest 15 min… |
| 1.3.6.1.4.1.498.8.4.6.2 | Scalarsnmp540LineStatsTxLevel | read-only | mandatory | Transmit level being generated into the private line circuit. This value is typically 6db. |
| 1.3.6.1.4.1.498.8.4.6.3 | Scalarsnmp540LineStatsRxInterpretation | read-only | mandatory | This object the characterizes LineStats readings. Interpretation code Meaning ..................... ........................... noSignal(1) No line signal is b… |
| 1.3.6.1.4.1.498.8.4.6.4 | Scalarsnmp540LineStatsRxLevel | read-only | mandatory | This object reports the receive level measurement for the selected interval. The range reported is from -50dB to +6dB. |
| 1.3.6.1.4.1.498.8.4.6.5 | Scalarsnmp540LineStatsSignalToNoiseRatio | read-only | mandatory | This object will the report the signal to noise ratio ranging from 0db to 50db for the selected interval. The value is absolute. If RxInterpretation reports sT… |
| 1.3.6.1.4.1.498.8.4.6.6 | Scalarsnmp540LineStatsSignalQuality | read-only | mandatory | This object reports the signal quality of the line, for the selected interval. |
| 1.3.6.1.4.1.498.8.4.6.7 | Scalarsnmp540LineStatsJitter | read-only | mandatory | This object will the report the percent jitter of the line, for the selected interval. |
| 1.3.6.1.4.1.498.8.4.6.8 | Scalarsnmp540LineStatsBpvCount | read-only | mandatory | This object will the report the number of bipolar violation codes received during for the selected LineStatsInterval. |
| 1.3.6.1.4.1.498.8.4.6.9 | Scalarsnmp540LineStatsFrameLossCount | read-only | mandatory | This object will the report the number frame losses received for the selected LineStatsInterval. |
| 1.3.6.1.4.1.498.8.4.7 | Nodesnmp540DiagTest | |||
| 1.3.6.1.4.1.498.8.4.7.1 | Scalarsnmp540DiagTestPattern | read-write | mandatory | The Self Test Pattern choices generated internally by the snmp540 are 511 Pattern (snmp540Send511Pattern(2)), 2047 pattern, (snmp540Send2047Pattern(3)) and 15 … |
| 1.3.6.1.4.1.498.8.4.7.2 | Scalarsnmp540DiagTestExceptions | read-only | mandatory | Indicates exceptions that have occurred that may affect interpretation of the test results. The exception values are: value exception: ....... ................… |
| 1.3.6.1.4.1.498.8.4.7.3 | Scalarsnmp540DiagBitErrors | read-only | mandatory | The bit errors of the most recently run diagnostic test. If TestExceptions reports bitsOutOfRange, this object should be ignored. |
| 1.3.6.1.4.1.498.8.4.7.4 | Scalarsnmp540DiagBlockErrors | read-only | mandatory | The block errors of the most recently run diagnostic test. |
| 1.3.6.1.4.1.498.8.4.7.5 | Scalarsnmp540RlLoopType | read-write | mandatory | The value Pn127(1), will use a PN127 loopback sequence to initiate a remote loopback test. The value v54(2) will use a V54 loopback sequence to initiate a remo… |
| 1.3.6.1.4.1.498.8.4.7.6 | Scalarsnmp540DiagBlocksToSend | read-write | mandatory | Specifies the number of test pattern blocks to generate during the test. The requested number of blocks are sent and checked during the test as a means of veri… |
| 1.3.6.1.4.1.498.8.4.7.7 | Scalarsnmp540DiagControl | read-write | mandatory | The lineloop(2) selection places the snmp540 into line loopback mode. The noTest(1) and telcoLoop(5) are READ ONLY values. NoTest(1) indicates that no diagnost… |
| 1.3.6.1.4.1.498.8.4.8 | Nodesnmp540Led | |||
| 1.3.6.1.4.1.498.8.4.8.1 | Scalarsnmp540LedStatus | read-only | mandatory | |
| 1.3.6.1.4.1.498.8.4.9 | Scalarsnmp540DeviceSerialNumber | read-only | mandatory | Display's the unique serial number of this device. The octet string starts with the two byte product code (0540) followed by a reserved byte value (rr) and the… |