STMIB
1686 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | -- TRAP-TYPE -- |
| RFC1155-SMI | Counter enterprises Gauge IpAddress NetworkAddress TimeTicks |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.16 | Nodetimeplex | |||
| 1.3.6.1.4.1.16.101 | Nodesynchrony | |||
| 1.3.6.1.4.1.16.101.1 | Nodest50 | |||
| 1.3.6.1.4.1.16.101.1.1 | Nodesecurity | |||
| 1.3.6.1.4.1.16.101.1.2 | Noderesource | |||
| 1.3.6.1.4.1.16.101.1.2.1 | NodereConfig | |||
| 1.3.6.1.4.1.16.101.1.2.1.1 | NoderecfPartitionHeader | |||
| 1.3.6.1.4.1.16.101.1.2.1.1.1 | ScalarrecfPartitionControl | write-only | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.4.1.16.101.1.2.1.1.2 | ScalarrecfPartitionCRCCheck | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.1.3 | ScalarrecfPartitionFlushMode | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.4.1.16.101.1.2.1.2 | NoderecfNode | |||
| 1.3.6.1.4.1.16.101.1.2.1.2.1 | NoderecfNodeEntry | |||
| 1.3.6.1.4.1.16.101.1.2.1.2.1.1 | ScalarrecfNodeUpdate | read-only | mandatory | Parameter Type = Internal. If set to updateNestReq, need to execute restNodeDiagnostics(updateNest) to load. |
| 1.3.6.1.4.1.16.101.1.2.1.2.1.2 | ScalarrecfNodeDescr | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.4.1.16.101.1.2.1.2.1.3 | ScalarrecfNodeContact | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.4.1.16.101.1.2.1.2.1.4 | ScalarrecfNodeName | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.4.1.16.101.1.2.1.2.1.5 | ScalarrecfNodeLocation | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.4.1.16.101.1.2.1.2.1.6 | ScalarrecfNodeNumberOfNest | read-write | mandatory | Parameter Type = Intrusive. New number of nests will not operate until restNodeDiagnostics(updateNest). |
| 1.3.6.1.4.1.16.101.1.2.1.2.1.7 | ScalarrecfNodeClockSwitch | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.4.1.16.101.1.2.1.2.1.8 | ScalarrecfNodeAlarmRelay | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.4.1.16.101.1.2.1.2.2 | TablerecfClockTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.2.2.1 | RowrecfClockEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.2.2.1.1 | ColumnrecfClockIndex | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.2.2.1.2 | ColumnrecfClockStartMode | read-write | mandatory | Parameter Type = Non-intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.2.2.1.3 | ColumnrecfClockUpdate | read-only | mandatory | Parameter Type = Internal. If set to updateReq, need to execute restNodeDiagnostics(updateClockTable) to load. |
| 1.3.6.1.4.1.16.101.1.2.1.2.2.1.4 | ColumnrecfClockType | read-write | mandatory | Parameter Type = Non-intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.2.2.1.5 | ColumnrecfClockStationSpeed | read-write | mandatory | Parameter Type = Non-intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.2.2.1.6 | ColumnrecfClockPortSource | read-write | mandatory | Parameter Type = Non-intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.2.2.1.7 | ColumnrecfClockQuality | read-write | mandatory | Parameter Type = Non-intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.2.2.1.8 | ColumnrecfClockPriority | read-write | mandatory | Parameter Type = Non-intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.2.3 | TablerecfAvailResourceTable | not-accessible | mandatory | This MIB section serves the purpose of finding an available resource of the type specified by the instance identifier. The values of the instance identifier ar… |
| 1.3.6.1.4.1.16.101.1.2.1.2.3.1 | RowrecfAvailResourceEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.4.1.16.101.1.2.1.2.3.1.1 | ColumnrecfAvailResourceType | read-only | mandatory | Parameter Type = Internal. Specifies the ST resource type to search. The possible values are: - link2TranslationIndex - find an available entry in recfLink2Tra… |
| 1.3.6.1.4.1.16.101.1.2.1.2.3.1.2 | ColumnrecfAvailResourceId | read-only | mandatory | Parameter Type = Internal. The return value specifies an available ST resource address in the format used to access the MIB section of the specified type. If t… |
| 1.3.6.1.4.1.16.101.1.2.1.3 | TablerecfNestTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.3.1 | RowrecfNestEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.3.1.1 | ColumnrecfNestAddr | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.3.1.2 | ColumnrecfNestDesc | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.4.1.16.101.1.2.1.4 | TablerecfSlotTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.4.1 | RowrecfSlotEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.4.1.1 | ColumnrecfSlotAddr | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.4.1.2 | ColumnrecfSlotModuleStartMode | read-write | mandatory | Parameter Type = Intrusive. Setting to erase will fail if any of the following conditions are true: (1) The module's redundant mode is set to one-to-one redund… |
| 1.3.6.1.4.1.16.101.1.2.1.4.1.3 | ColumnrecfSlotUpdate | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.4.1.4 | ColumnrecfSlotModuleDesc | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.4.1.16.101.1.2.1.4.1.5 | ColumnrecfSlotModuleType | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.4.1.6 | ColumnrecfSlotModuleSubType | read-write | mandatory | Parameter Type = Intrusive. For NCP modules: NCP-1 value is 1 NCP-2 value is 2 NCP-3 value is 3 For FSM modules: FSM-16 value is 1 FSM-64 value is 2 For T1M mo… |
| 1.3.6.1.4.1.16.101.1.2.1.4.1.7 | ColumnrecfSlotRedundantMode | read-write | mandatory | Parameter Type = Intrusive. Server modules will always have group redundancy regardless of the value of this field. Default value is none for I/O modules and g… |
| 1.3.6.1.4.1.16.101.1.2.1.4.1.8 | ColumnrecfSlotGroupID | read-write | mandatory | Parameter Type = Intrusive. Applies to server modules only for group redundancy. |
| 1.3.6.1.4.1.16.101.1.2.1.4.1.9 | ColumnrecfSlotModuleMaxBypass | read-write | mandatory | Parameter Type = Non-intrusive. FSM or DSM module bypassing capability in terms of percentage. |
| 1.3.6.1.4.1.16.101.1.2.1.4.1.10 | ColumnrecfSlotModuleMaxSource | read-write | mandatory | Parameter Type = Non-intrusive. FSM module termination capability in terms of percentage. |
| 1.3.6.1.4.1.16.101.1.2.1.4.1.11 | ColumnrecfSlotModuleStartDiagMask | read-write | mandatory | Parameter Type = Intrusive. This mask allows a module to be online or standby even though some items as marked by the mask have failed startup diagnostics. For… |
| 1.3.6.1.4.1.16.101.1.2.1.4.1.12 | ColumnrecfSlotModuleBgdDiagMask | read-write | mandatory | Parameter Type = Non-intrusive. This mask allows a module to be online or standby even though some items as marked by the mask have failed background diagnosti… |
| 1.3.6.1.4.1.16.101.1.2.1.4.1.13 | ColumnrecfSlotModulePortDiagMask | read-write | mandatory | Parameter Type = Non-intrusive. This mask allows a module to be online or standby even though some items as marked by the mask have failed port startup diagnos… |
| 1.3.6.1.4.1.16.101.1.2.1.4.1.14 | ColumnrecfSlotModuleDiagoseMode | read-write | mandatory | Parameter Type = Non-intrusive. INTRODUCED 2.0.1 This parameter is used to control module-specific code for diagnosing problems. The interpretation of values f… |
| 1.3.6.1.4.1.16.101.1.2.1.4.1.15 | ColumnrecfSlotModuleStartDiagMaskExt | read-write | mandatory | Parameter Type = Intrusive. INTRODUCED 2.0.1 This mask allows a module to be online or standby even though some items as marked by the mask have failed startup… |
| 1.3.6.1.4.1.16.101.1.2.1.4.1.16 | ColumnrecfSlotModuleBgdDiagMaskExt | read-write | mandatory | Parameter Type = Non-intrusive. INTRODUCED 2.0.1 This mask allows a module to be online or standby even though some items as marked by the mask have failed bac… |
| 1.3.6.1.4.1.16.101.1.2.1.5 | NoderecfModule | |||
| 1.3.6.1.4.1.16.101.1.2.1.5.1 | TablerecfModuleFsm16Table | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.5.1.1 | RowrecfModuleFsm16Entry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.5.1.1.1 | ColumnrecfModuleFsm16Addr | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.5.1.1.2 | ColumnrecfModuleFsm16Partition | read-write | mandatory | Parameter Type = Non-intrusive. Each two bytes is the partition ID of a physical port on the module. Partition 1 is for CNMS. Partition 0xFFFE (65534) is for a… |
| 1.3.6.1.4.1.16.101.1.2.1.5.2 | TablerecfModuleFsm64Table | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.5.2.1 | RowrecfModuleFsm64Entry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.5.2.1.1 | ColumnrecfModuleFsm64Addr | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.5.2.1.2 | ColumnrecfModuleFsm64Partition | read-write | mandatory | Parameter Type = Non-intrusive. Each two bytes is the partition ID of a physical port on the module. Partition 1 is for CNMS. Partition 0xFFFE (65534) is for a… |
| 1.3.6.1.4.1.16.101.1.2.1.5.3 | TablerecfModuleSgmAgTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.5.3.1 | RowrecfModuleSgmAgEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.5.3.1.1 | ColumnrecfModuleSgmAgAddr | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.5.3.1.2 | ColumnrecfModuleSgmAgPartition | read-write | mandatory | Parameter Type = Non-intrusive. Each two bytes is the partition ID of a physical port on the module. Partition 1 is for CNMS. Partition 0xFFFE (65534) is for a… |
| 1.3.6.1.4.1.16.101.1.2.1.5.4 | TablerecfModuleAsmTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.5.4.1 | RowrecfModuleAsmEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.5.4.1.1 | ColumnrecfModuleAsmAddr | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.5.4.1.2 | ColumnrecfModuleAsmPartition | read-write | mandatory | Parameter Type = Non-intrusive. Each two bytes is the partition ID of a physical engine on the module. Partition 1 is for CNMS. Partition 0xFFFE (65534) is for… |
| 1.3.6.1.4.1.16.101.1.2.1.5.4.1.3 | ColumnrecfModuleAsmCelpPartition | read-write | mandatory | Parameter Type = Non-intrusive. Each two bytes is the partition ID of a CELP license on the module. Partition 1 is for CNMS. Partition 0xFFFE (65534) is for an… |
| 1.3.6.1.4.1.16.101.1.2.1.5.4.1.4 | ColumnrecfModuleAsmMinCelpPorts | read-write | mandatory | Parameter Type = Non-intrusive. Defines the number of the ASM ports that cannot be used for anything else but CELP application. |
| 1.3.6.1.4.1.16.101.1.2.1.5.4.1.5 | ColumnrecfModuleAsmApplType | read-write | mandatory | Parameter Type = Intrusive. Allows the user to specify a specific application type to be allocated to this ASM module. Ports with other application types will … |
| 1.3.6.1.4.1.16.101.1.2.1.5.5 | TablerecfModuleLgmTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.5.5.1 | RowrecfModuleLgmEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.5.5.1.1 | ColumnrecfModuleLgmAddr | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.5.5.1.2 | ColumnrecfModuleLgmPartition | read-write | mandatory | Parameter Type = Non-intrusive. Each two bytes is the partition ID of a VILC aggregate on the module. Partition 1 is for CNMS. Partition 0xFFFE (65534) is for … |
| 1.3.6.1.4.1.16.101.1.2.1.5.6 | NoderecfModuleDsm | |||
| 1.3.6.1.4.1.16.101.1.2.1.5.6.1 | TablerecfModuleDsmTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.5.6.1.1 | RowrecfModuleDsmEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.4.1.16.101.1.2.1.5.6.1.1.1 | ColumnrecfModuleDsmAddr | read-only | mandatory | Parameter Type = Internal. DSM module address. Format is nest.slot. |
| 1.3.6.1.4.1.16.101.1.2.1.5.6.1.1.2 | ColumnrecfModuleDsmPartitionMap | read-write | mandatory | Parameter Type = Non-intrusive. Every octet pair is the partition ID of a physical port on the module. Partition 1 is for CNMS. Partition 0xFFFE (65534) is for… |
| 1.3.6.1.4.1.16.101.1.2.1.5.6.1.1.3 | ColumnrecfModuleDsmPbxProtocol | read-write | mandatory | Parameter Type = Intrusive. All D-channels connected to this DSM module will need to be set up with the same PBX protocol as set here. Changes to this field wi… |
| 1.3.6.1.4.1.16.101.1.2.1.5.6.1.1.4 | ColumnrecfModuleDsmActiveLev1CDRMode | read-write | mandatory | Parameter Type = Non-intrusive. Specifies whether level 1 Call Detail Record for the calls in progress are to be generated by the DSM. This parameter affects a… |
| 1.3.6.1.4.1.16.101.1.2.1.5.6.1.1.5 | ColumnrecfModuleDsmRecordLev1CDRMode | read-write | mandatory | Parameter Type = Non-intrusive. Specifies whether level 1 Call Detail Record for the completed calls are to be generated by the DSM. This parameter affects all… |
| 1.3.6.1.4.1.16.101.1.2.1.5.6.1.1.6 | ColumnrecfModuleDsmActiveLev2CDRMode | read-write | mandatory | Parameter Type = Non-intrusive. Specifies whether level 2 Call Detail Record for the calls in progress are to be generated by the DSM. This parameter affects a… |
| 1.3.6.1.4.1.16.101.1.2.1.5.6.1.1.7 | ColumnrecfModuleDsmRecordLev2CDRMode | read-write | mandatory | Parameter Type = Non-intrusive. Specifies whether level 2 Call Detail Record for the completed calls are to be generated by the DSM. This parameter affects all… |
| 1.3.6.1.4.1.16.101.1.2.1.5.6.2 | TablerecfModDsmRecCDRLogTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.5.6.2.1 | RowrecfModDsmRecCDRLogEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.4.1.16.101.1.2.1.5.6.2.1.1 | ColumnrecfModDsmRecCDRLogAddr | read-only | mandatory | Parameter Type = Internal. Address of this DSM module. Format is nest.slot. |
| 1.3.6.1.4.1.16.101.1.2.1.5.6.2.1.2 | ColumnrecfModDsmRecCDRLogIndex | read-only | mandatory | Parameter Type = Internal. Specifies the CDR log to access. |
| 1.3.6.1.4.1.16.101.1.2.1.5.6.2.1.3 | ColumnrecfModDsmRecCDRLogControlMode | read-write | mandatory | Parameter Type = Non-intrusive. Changes will not affect channels that are already connected. Disable will prevent new CDRs to be recorded in this log. Erase wi… |
| 1.3.6.1.4.1.16.101.1.2.1.5.6.2.1.4 | ColumnrecfModDsmRecCDRLogSize | read-write | mandatory | Parameter Type = Non-intrusive. Assigns the maximum number of CDRs that may be stored in this CDR log. The total size of all CDR logs on this module cannot exc… |
| 1.3.6.1.4.1.16.101.1.2.1.5.6.2.1.5 | ColumnrecfModDsmRecCDRLogOvThrshld | read-write | mandatory | Parameter Type = Non-intrusive. Defines an overflow threshold on this CDR log. When reached, the threshold flag is set, and the threshold exceeded alarm is iss… |
| 1.3.6.1.4.1.16.101.1.2.1.5.6.2.1.6 | ColumnrecfModDsmRecCDRLogPartitionID | read-write | mandatory | Parameter Type = Non-intrusive. Specifies partition ID of this CDR log. Changes to this field will be reflected in recfSlotUpdate. A module update will be requ… |
| 1.3.6.1.4.1.16.101.1.2.1.6 | NoderecfPort | |||
| 1.3.6.1.4.1.16.101.1.2.1.6.1 | TablerecfT1mPortTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.6.1.1 | RowrecfT1mPortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.6.1.1.1 | ColumnrecfT1mPortAddr | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.6.1.1.2 | ColumnrecfT1mPortStartMode | read-write | mandatory | Parameter Type = Intrusive. Setting to erase will fail if the port has any unremoved INLs or channels that are not disconnected. Otherwise, it will return the … |
| 1.3.6.1.4.1.16.101.1.2.1.6.1.1.3 | ColumnrecfT1mPortUpdate | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.6.1.1.4 | ColumnrecfT1mPortFraming | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.1.1.5 | ColumnrecfT1mPortLineCodeType | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.1.1.6 | ColumnrecfT1mPortDs1Option | read-write | mandatory | Parameter Type = Intrusive. This field refers to the line build out of the T1M port. The values should be interpreted as follows: a: 0 dB b: -7.5 dB c: -15 dB. |
| 1.3.6.1.4.1.16.101.1.2.1.6.1.1.7 | ColumnrecfT1mPortDsx1Distance | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.1.1.8 | ColumnrecfT1mPortEquGain | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.1.1.9 | ColumnrecfT1mPortBundleMap | read-write | mandatory | Parameter Type = Immediate. Each byte represents a DS0 in T1m Port, starting 1 from the right most byte. The bundle is identified by the number of the lowest D… |
| 1.3.6.1.4.1.16.101.1.2.1.6.1.1.10 | ColumnrecfT1mPortErrorThreshold | read-write | mandatory | Parameter Type = Non-intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.1.1.11 | ColumnrecfT1mPortSevereThreshold | read-write | mandatory | Parameter Type = Non-intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.1.1.12 | ColumnrecfT1mPortAlarmThreshold | read-write | mandatory | Parameter Type = Non-intrusive. If port BER quality is below this threshold for four consecutive seconds, a port error alarm will be sent. |
| 1.3.6.1.4.1.16.101.1.2.1.6.1.1.13 | ColumnrecfT1mPortFailThreshold | read-write | mandatory | Parameter Type = Non-intrusive. If port BER quality is below this threshold for ten consecutive seconds, a port down alarm will be sent. |
| 1.3.6.1.4.1.16.101.1.2.1.6.1.1.14 | ColumnrecfT1mPortFailToggleRequest | read-write | mandatory | Parameter Type = Non-intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.1.1.15 | ColumnrecfT1mPortOOSBitPattern | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.1.1.16 | ColumnrecfT1mPortOOSASignaling | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.1.1.17 | ColumnrecfT1mPortOOSBSignaling | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.1.1.18 | ColumnrecfT1mPortOOSCDSignaling | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.1.1.19 | ColumnrecfT1mPortSigInversion | read-write | deprecated | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.2 | TablerecfE1mPortTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.6.2.1 | RowrecfE1mPortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.6.2.1.1 | ColumnrecfE1mPortAddr | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.6.2.1.2 | ColumnrecfE1mPortStartMode | read-write | mandatory | Parameter Type = Intrusive. Setting to erase will fail if the port has any unremoved INLs or channels that are not disconnected. Otherwise, it will return the … |
| 1.3.6.1.4.1.16.101.1.2.1.6.2.1.3 | ColumnrecfE1mPortUpdate | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.6.2.1.4 | ColumnrecfE1mPortFraming | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.2.1.5 | ColumnrecfE1mPortCrcMultiFrame | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.2.1.6 | ColumnrecfE1mPortSigInversion | read-write | deprecated | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.2.1.7 | ColumnrecfE1mPortInternationalBit | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.2.1.8 | ColumnrecfE1mPortNationalBit | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.2.1.9 | ColumnrecfE1mPortTransmitEBit | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.2.1.10 | ColumnrecfE1mPortReceiveEBit | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.2.1.11 | ColumnrecfE1mPortBundleMap | read-write | mandatory | Parameter Type = Immediate. Each byte represents a DS0 in E1m Port, starting 1 from the right most byte. The bundle is identified by the number of the lowest D… |
| 1.3.6.1.4.1.16.101.1.2.1.6.2.1.12 | ColumnrecfE1mPortErrorThreshold | read-write | mandatory | Parameter Type = Non-intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.2.1.13 | ColumnrecfE1mPortSevereThreshold | read-write | mandatory | Parameter Type = Non-intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.2.1.14 | ColumnrecfE1mPortAlarmThreshold | read-write | mandatory | Parameter Type = Non-intrusive. If port BER quality is below this threshold for four consecutive seconds, a port error alarm will be sent. |
| 1.3.6.1.4.1.16.101.1.2.1.6.2.1.15 | ColumnrecfE1mPortFailThreshold | read-write | mandatory | Parameter Type = Non-intrusive. If port BER quality is below this threshold for ten consecutive seconds, a port down alarm will be sent. |
| 1.3.6.1.4.1.16.101.1.2.1.6.2.1.16 | ColumnrecfE1mPortFailToggleRequest | read-write | mandatory | Parameter Type = Non-intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.2.1.17 | ColumnrecfE1mPortOOSBitPattern | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.2.1.18 | ColumnrecfE1mPortOOSASignaling | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.2.1.19 | ColumnrecfE1mPortOOSBSignaling | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.2.1.20 | ColumnrecfE1mPortOOSCDSignaling | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.3 | TablerecfSdmPortTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.6.3.1 | RowrecfSdmPortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.6.3.1.1 | ColumnrecfSdmPortAddr | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.6.3.1.2 | ColumnrecfSdmPortStartMode | read-write | mandatory | Parameter Type = Intrusive. Setting to erase will fail if the port has any unremoved INLs or channels that are not disconnected. Otherwise, it will return the … |
| 1.3.6.1.4.1.16.101.1.2.1.6.3.1.3 | ColumnrecfSdmPortUpdate | read-only | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.3.1.4 | ColumnrecfSdmPortSpeed | read-write | mandatory | Parameter Type = Intrusive. s is for subrate speeds. b is for bundle speeds (n x 64K). sf is for stuffed speeds (n x 56K). bsf is for speeds that can be bundle… |
| 1.3.6.1.4.1.16.101.1.2.1.6.3.1.5 | ColumnrecfSdmPortInterface | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.3.1.6 | ColumnrecfSdmPortTxClockSource | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.3.1.7 | ColumnrecfSdmPortBitMode | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.3.1.8 | ColumnrecfSdmPortOOSOper | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.3.1.9 | ColumnrecfSdmPortGen | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.3.1.10 | ColumnrecfSdmPortPolarity | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.3.1.11 | ColumnrecfSdmPortType | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.3.1.12 | ColumnrecfSdmPortINLNumber | read-only | mandatory | Parameter Type = Intrusive. Applicable only if recfSdmPortType is set to inl. |
| 1.3.6.1.4.1.16.101.1.2.1.6.3.1.13 | ColumnrecfSdmDeviceType | read-write | mandatory | Parameter Type = Intrusive. This field indicates the type of device connected to the port. Values 1-10 and 255 are reserved by ST-50, of which 1 is for voice, … |
| 1.3.6.1.4.1.16.101.1.2.1.6.3.1.14 | ColumnrecfSdmPortPartitionID | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.3.1.15 | ColumnrecfSdmPortFunctions | read-write | mandatory | Parameter Type = Intrusive. The four least significant bits represent whether the function mapped to that bit should be forced or not. bit 1 (lsb) - DSR if DCE… |
| 1.3.6.1.4.1.16.101.1.2.1.6.3.1.16 | ColumnrecfSdmPortContentionSet | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.3.1.17 | ColumnrecfSdmPortLoopbackSupport | read-write | mandatory | Parameter Type = Intrusive. Indicates whether the SDM port should support the signals for LL, RL, and TM. If a signal is supported, then that loopback signal w… |
| 1.3.6.1.4.1.16.101.1.2.1.6.3.1.18 | ColumnrecfSdmPortSatelliteBuffer | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.3.1.19 | ColumnrecfSdmPortFailToggleRequest | read-write | mandatory | Parameter Type = Non-intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.6.3.1.20 | ColumnrecfSdmPortKGPolarity | read-write | mandatory | Parameter Type = Intrusive. Specifies the polarity of KG-resync signal. |
| 1.3.6.1.4.1.16.101.1.2.1.6.3.1.21 | ColumnrecfSdmPortKGSignalType | read-write | mandatory | Parameter Type = Intrusive. Specifies the type of of KG-resync signal. |
| 1.3.6.1.4.1.16.101.1.2.1.6.3.1.22 | ColumnrecfSdmPortKGMode | read-write | mandatory | Parameter Type = Intrusive. Specifies the KG-resync mode. |
| 1.3.6.1.4.1.16.101.1.2.1.7 | TablerecfBundleTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.7.1 | RowrecfBundleEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.7.1.1 | ColumnrecfBundleAddr | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.7.1.2 | ColumnrecfBundleStartMode | read-write | mandatory | Parameter Type = Intrusive. Setting to erase will fail if the bundle has an unremoved INL or a channel that is not disconnected. Otherwise, it will erase the b… |
| 1.3.6.1.4.1.16.101.1.2.1.7.1.3 | ColumnrecfBundleUpdate | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.7.1.4 | ColumnrecfBundleSignaling | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.7.1.5 | ColumnrecfBundleOOSBitPattern | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.7.1.6 | ColumnrecfBundleOOSASignaling | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.7.1.7 | ColumnrecfBundleOOSBSignaling | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.7.1.8 | ColumnrecfBundleOOSCDSignaling | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.7.1.9 | ColumnrecfBundleNullIdlePattern | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.7.1.10 | ColumnrecfBundleBwCntIdlePattern | read-write | mandatory | Parameter Type = Intrusive. Bit pattern output to equipment indicating bundle availability. T1M bundles will have a default pattern of a0-b0-c0-d0. E1M bundles… |
| 1.3.6.1.4.1.16.101.1.2.1.7.1.11 | ColumnrecfBundleBusyOutTimer | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.7.1.12 | ColumnrecfBundleSeizureTime | read-write | mandatory | Parameter Type = Non-intrusive. For bandwidth contention channel. |
| 1.3.6.1.4.1.16.101.1.2.1.7.1.13 | ColumnrecfBundlePreemptionTime | read-write | mandatory | Parameter Type = Non-intrusive. For bandwidth contention channel. |
| 1.3.6.1.4.1.16.101.1.2.1.7.1.14 | ColumnrecfBundleOrgDisconnectTime | read-write | mandatory | Parameter Type = Non-intrusive. For bandwidth contention channel. Units that start with 's' are in units of 1/10 seconds (i.e., s10 is 1.0 seconds). |
| 1.3.6.1.4.1.16.101.1.2.1.7.1.15 | ColumnrecfBundleAttenuationRx | read-write | mandatory | Parameter Type = Intrusive. For voice channel. |
| 1.3.6.1.4.1.16.101.1.2.1.7.1.16 | ColumnrecfBundleAttenuationTx | read-write | mandatory | Parameter Type = Intrusive. For voice channel. |
| 1.3.6.1.4.1.16.101.1.2.1.7.1.17 | ColumnrecfBundleType | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.7.1.18 | ColumnrecfBundleINLNumber | read-only | mandatory | Parameter Type = Internal. Applicable only if recfBundleType is set to inl. |
| 1.3.6.1.4.1.16.101.1.2.1.7.1.19 | ColumnrecfBundleDeviceType | read-write | mandatory | Parameter Type = Non-intrusive. This field indicates the type of device connected to the port. Values 1-10 and 255 are reserved by ST-50, of which 1 is for voi… |
| 1.3.6.1.4.1.16.101.1.2.1.7.1.20 | ColumnrecfBundleContentionSet | read-write | mandatory | Parameter Type = Intrusive. If bundle type is not bandwidth contention, this field is ignored. This field defines the type of contention application. E&M conte… |
| 1.3.6.1.4.1.16.101.1.2.1.7.1.21 | ColumnrecfBundlePartitionID | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.7.1.22 | ColumnrecfBundleBwCntBusyPattern | read-write | mandatory | Parameter Type = Intrusive. Bit pattern output to equipment indicating bundle busy. If the value is oos, then the busy pattern will be the same as the OOS idle… |
| 1.3.6.1.4.1.16.101.1.2.1.7.1.23 | ColumnrecfBundleSigInversion | read-write | mandatory | Parameter Type = Intrusive. INTRODUCED 2.0.0 For an E1M bundle, the meanings of these values are reversed. That is, if this parameter is set as normal, the ABC… |
| 1.3.6.1.4.1.16.101.1.2.1.7.1.24 | ColumnrecfBundleDataPolarity | read-write | mandatory | Parameter Type = Intrusive. INTRODUCED 2.0.0 The default value must be used unless specific user equipment explicitly requires data to be inverted. |
| 1.3.6.1.4.1.16.101.1.2.1.7.1.25 | ColumnrecfBundlePCMLaw | read-write | mandatory | Parameter Type = Intrusive. INTRODUCED 2.0.0 The values specify the following setup: <native> - T1M - u_Law E1M - a_Law <converted> - T1M - a_Law E1M - u_Law. |
| 1.3.6.1.4.1.16.101.1.2.1.8 | TablerecfINLTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.8.1 | RowrecfINLEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.8.1.1 | ColumnrecfINLNumber | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.8.1.2 | ColumnrecfINLAddr | read-write | mandatory | Parameter Type = Intrusive. Setting this field will set the INL number field in the port or bundle configuration to this INL's number. |
| 1.3.6.1.4.1.16.101.1.2.1.8.1.3 | ColumnrecfINLStartMode | read-write | mandatory | Parameter Type = Intrusive. Setting to erase will fail if the INL has not been removed. Otherwise, it will erase the INL configuration, and set the INL number … |
| 1.3.6.1.4.1.16.101.1.2.1.8.1.4 | ColumnrecfINLUpdate | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.8.1.5 | ColumnrecfINLArqCir | read-write | mandatory | Parameter Type = Intrusive. Unit of bps. |
| 1.3.6.1.4.1.16.101.1.2.1.8.1.6 | ColumnrecfINLMaxPacketDS0 | read-write | mandatory | Parameter Type = Intrusive. Maximum packet bandwidth, in units of DS0. (INL Bandwidth - recfMaxPacketDS0) is the guaranteed TDM bandwidth. |
| 1.3.6.1.4.1.16.101.1.2.1.8.1.7 | ColumnrecfINLPacketCirOccupy | read-write | mandatory | Parameter Type = Intrusive. This number represents the CIR occupancy percentage (x) of the packet band bandwidth. The INL bandwidth allocation shall follow the… |
| 1.3.6.1.4.1.16.101.1.2.1.8.1.8 | ColumnrecfINLMaxTDMDS0 | read-write | mandatory | Parameter Type = Intrusive. Maximum TDM bandwidth, in units of DS0. (INL Bandwidth - recfMaxTDMDS0) is the guaranteed packet bandwidth. |
| 1.3.6.1.4.1.16.101.1.2.1.8.1.9 | ColumnrecfINLGroup | read-write | mandatory | Parameter Type = Non-intrusive. Up to seven groups for each INL. Bit map bits 1 (lsb) to 7 indicates the group(s) of the INL. |
| 1.3.6.1.4.1.16.101.1.2.1.8.1.10 | ColumnrecfINLCost | read-write | mandatory | Parameter Type = Non-intrusive. Assigned by user. |
| 1.3.6.1.4.1.16.101.1.2.1.8.1.11 | ColumnrecfINLEncryption | read-write | mandatory | Parameter Type = Non-intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.8.1.12 | ColumnrecfINLSatelliteHop | read-write | mandatory | Parameter Type = Non-intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.8.1.13 | ColumnrecfINLOOSTimer | read-write | mandatory | Parameter Type = Non-intrusive. In units of seconds. To disqualify a INL beyond. |
| 1.3.6.1.4.1.16.101.1.2.1.8.1.14 | ColumnrecfINLOrig | read-write | mandatory | Parameter Type = Internal. For EMS usage. |
| 1.3.6.1.4.1.16.101.1.2.1.8.1.15 | ColumnrecfINLRemoteNodeID | read-write | mandatory | Parameter Type = Intrusive. 0 means don't care. |
| 1.3.6.1.4.1.16.101.1.2.1.8.1.16 | ColumnrecfINLRemoteINLID | read-write | mandatory | Parameter Type = Intrusive. INL number of remote side. 0 means don't care. |
| 1.3.6.1.4.1.16.101.1.2.1.8.1.17 | ColumnrecfINLPartitionID | read-only | mandatory | Parameter Type = Internal. Used by security server to enforce shared node. |
| 1.3.6.1.4.1.16.101.1.2.1.8.1.18 | ColumnrecfINLKGMode | read-only | mandatory | Parameter Type = Internal. Used by Link Maintenance to take action in KG-resync mode. |
| 1.3.6.1.4.1.16.101.1.2.1.9 | TablerecfTDMChannelTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.9.1 | RowrecfTDMChannelEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.9.1.1 | ColumnrecfTDMChannelAddr | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.9.1.2 | ColumnrecfTDMChannelDestNodeID | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.4.1.16.101.1.2.1.9.1.3 | ColumnrecfTDMChannelDestAddr | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.4.1.16.101.1.2.1.9.1.4 | ColumnrecfTDMChannelControlMode | read-write | mandatory | Parameter Type = Intrusive. Indicates whether the channel can be used in a connection request or not. The value erase is used to wipe out the channel configura… |
| 1.3.6.1.4.1.16.101.1.2.1.9.1.5 | ColumnrecfTDMChannelUpdate | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.9.1.6 | ColumnrecfTDMChannelModuleType | read-only | mandatory | Parameter Type = Internal. The type of module on which this channel endpoint is located. Derived from the port or that the channel is configured on. |
| 1.3.6.1.4.1.16.101.1.2.1.9.1.7 | ColumnrecfTDMChannelDeviceType | read-only | mandatory | Parameter Type = Internal. The type of device connected to this channel endpoint. Derived from the port or bundle that the channel is configured on. Always zer… |
| 1.3.6.1.4.1.16.101.1.2.1.9.1.8 | ColumnrecfTDMChannelProfile | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.9.1.9 | ColumnrecfTDMChannelOrig | read-write | mandatory | Parameter Type = Internal. For EMS usage. |
| 1.3.6.1.4.1.16.101.1.2.1.9.1.10 | ColumnrecfTDMChannelPartitionID | read-only | mandatory | Parameter Type = Internal. Used by security server to enforce shared node. Derived from end point. |
| 1.3.6.1.4.1.16.101.1.2.1.9.1.11 | ColumnrecfTDMChannelState | read-only | mandatory | Parameter Type = Internal. If value is connected, then restChannelStatus is also set to connected. If value is processing, then restChannelStatus is set to any… |
| 1.3.6.1.4.1.16.101.1.2.1.9.1.12 | ColumnrecfTDMChannelDestCheckMode | read-write | mandatory | Parameter Type = Intrusive. Indicates if the remote node ID and remote address in the destination's channel MIB need to verify the source's node ID and address… |
| 1.3.6.1.4.1.16.101.1.2.1.9.1.13 | ColumnrecfTDMChannelConnectMode | read-write | mandatory | Parameter Type = Intrusive. Indicates whether a channel should be automatically connected when a port comes up, or if the user is responsible for connecting th… |
| 1.3.6.1.4.1.16.101.1.2.1.9.1.14 | ColumnrecfTDMChannelSpecialPrfType | read-write | mandatory | Parameter Type = Intrusive. INTRODUCED 2.0.0 Specifies the type of special profile that is used on this channel connection. |
| 1.3.6.1.4.1.16.101.1.2.1.9.1.15 | ColumnrecfTDMChannelSpecialProfile | read-write | mandatory | Parameter Type = Intrusive. INTRODUCED 2.0.0 Specifies the particular special profile index used on this channel connection. |
| 1.3.6.1.4.1.16.101.1.2.1.9.1.16 | ColumnrecfTDMChannelDestNodeType | read-write | mandatory | Parameter Type = Intrusive. INTRODUCED 2.0.0 This attribute defines the type of the destination node for this channel. If set to <link>, then the LGM translati… |
| 1.3.6.1.4.1.16.101.1.2.1.10 | NoderecfFrame | |||
| 1.3.6.1.4.1.16.101.1.2.1.10.1 | TablerecfFrPortTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.10.1.1 | RowrecfFrPortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.10.1.1.1 | ColumnrecfFrPortAddr | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.10.1.1.2 | ColumnrecfFrPortDescription | read-write | mandatory | Parameter Type = Intrusive. Used by EMS ITM and other applications. |
| 1.3.6.1.4.1.16.101.1.2.1.10.1.1.3 | ColumnrecfFrPortStartMode | read-write | mandatory | Parameter Type = Intrusive. Setting this to erase will erase the port configuration MIB, as well as any TDM and frame relay channels defined on this port. The … |
| 1.3.6.1.4.1.16.101.1.2.1.10.1.1.4 | ColumnrecfFrPortUpdate | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.10.1.1.5 | ColumnrecfFrPortLmiActive | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.10.1.1.6 | ColumnrecfFrPortLmiPollingTimer | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.10.1.1.7 | ColumnrecfFrPortLmiWaitingTimer | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.10.1.1.8 | ColumnrecfFrPortLmiFullEnqInterval | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.10.1.1.9 | ColumnrecfFrPortLmiMonitoredEvents | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.10.1.1.10 | ColumnrecfFrPortErrorThreshold | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.10.1.1.11 | ColumnrecfFrPortDeviceType | read-write | mandatory | Parameter Type = Intrusive. Indicates port usage. For regular HDLC ports, only one connection can be made. All HDLC ports shall be connected to an SDM I/O port. |
| 1.3.6.1.4.1.16.101.1.2.1.10.1.1.12 | ColumnrecfFrPortAd10NodeID | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.10.1.1.13 | ColumnrecfFrPortAd10PortID | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.10.1.1.14 | ColumnrecfFrPortBitMode | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.10.1.1.15 | ColumnrecfFrPortMaxFrameSize | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.10.1.1.16 | ColumnrecfFrPortSharedZeroFlag | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.10.1.1.17 | ColumnrecfFrPortMaxCIR | read-write | mandatory | Parameter Type = Intrusive. This value (in units of bps) is used to determine how many packets per second the I/O to server connection will require from the FS… |
| 1.3.6.1.4.1.16.101.1.2.1.10.1.1.18 | ColumnrecfFrPortAvgPktSize | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.10.1.1.19 | ColumnrecfFrPortAllocationPref | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.10.1.1.20 | ColumnrecfFrPortBillingSegSize | read-write | mandatory | Parameter Type = Intrusive. THIS ATTRIBUTE IS NOT USED. |
| 1.3.6.1.4.1.16.101.1.2.1.10.1.1.21 | ColumnrecfFrPortBillingControl | read-write | mandatory | Parameter Type = Intrusive. THIS ATTRIBUTE IS NOT USED. |
| 1.3.6.1.4.1.16.101.1.2.1.10.1.1.22 | ColumnrecfFrPortPartitionID | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.10.1.1.23 | ColumnrecfFrPortEncodingType | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.10.2 | TablerecfFrChannelTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.10.2.1 | RowrecfFrChannelEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.10.2.1.1 | ColumnrecfFrChannelAddr | read-only | mandatory | Parameter Type = Internal. If the end point is a HDLC port, EMS can define a DLCI (1-1023) |
| 1.3.6.1.4.1.16.101.1.2.1.10.2.1.2 | ColumnrecfFrChannelDestNodeID | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.10.2.1.3 | ColumnrecfFrChannelDestAddr | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.10.2.1.4 | ColumnrecfFrChannelControlMode | read-write | mandatory | Parameter Type = Intrusive. Indicates whether the channel can be used in a connection request or not. The value erase is used to wipe out the channel configura… |
| 1.3.6.1.4.1.16.101.1.2.1.10.2.1.5 | ColumnrecfFrChannelUpdate | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.10.2.1.6 | ColumnrecfFrChannelType | read-write | mandatory | Parameter Type = Intrusive. When a channel is added, a notification shall be sent to the associated FSM through maintenance agent. Regular connection is point-… |
| 1.3.6.1.4.1.16.101.1.2.1.10.2.1.7 | ColumnrecfFrChannelCirTransPriority | read-write | mandatory | Parameter Type = Intrusive. Use high for timing critical traffic. 7 is the highest priority. |
| 1.3.6.1.4.1.16.101.1.2.1.10.2.1.8 | ColumnrecfFrChannelCIR | read-write | mandatory | Parameter Type = Intrusive. Commit information rate (bps). |
| 1.3.6.1.4.1.16.101.1.2.1.10.2.1.9 | ColumnrecfFrChannelEIR | read-write | mandatory | Parameter Type = Intrusive. Excessive information rate (bps). |
| 1.3.6.1.4.1.16.101.1.2.1.10.2.1.10 | ColumnrecfFrChannelBc | read-write | mandatory | Parameter Type = Intrusive. Commit burst rate. |
| 1.3.6.1.4.1.16.101.1.2.1.10.2.1.11 | ColumnrecfFrChannelProfile | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.10.2.1.12 | ColumnrecfFrChannelOrig | read-write | mandatory | Parameter Type = Internal. For EMS internal usage. |
| 1.3.6.1.4.1.16.101.1.2.1.10.2.1.13 | ColumnrecfFrChannelPartitionID | read-write | mandatory | Parameter Type = Intrusive. Used for security on shared nodes. For channels defined on FSM port, this attribute can only be set to the port partition ID. For c… |
| 1.3.6.1.4.1.16.101.1.2.1.10.2.1.14 | ColumnrecfFrChannelState | read-only | mandatory | Parameter Type = Internal. If value is connected, then restChannelStatus is also set to connected. If value is processing, then restChannelStatus is set to any… |
| 1.3.6.1.4.1.16.101.1.2.1.10.2.1.15 | ColumnrecfFrChannelDestCheckMode | read-write | mandatory | Parameter Type = Intrusive. Indicates if the remote node ID and remote address in the destination's channel MIB need to verify the source's node ID and address… |
| 1.3.6.1.4.1.16.101.1.2.1.10.2.1.16 | ColumnrecfFrChannelConnectMode | read-write | mandatory | Parameter Type = Intrusive. Indicates whether a channel should be automatically connected when a port comes up, or if the user is responsible for connecting th… |
| 1.3.6.1.4.1.16.101.1.2.1.10.2.1.17 | ColumnrecfFrChannelModuleType | read-only | mandatory | Parameter Type = Internal. The type of module on which this channel endpoint is located. Derived from the port or that the channel is configured on. |
| 1.3.6.1.4.1.16.101.1.2.1.11 | NoderecfAd10Port | |||
| 1.3.6.1.4.1.16.101.1.2.1.11.1 | TablerecfAd10AgmPortTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.11.1.1 | RowrecfAd10AgmPortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.11.1.1.1 | ColumnrecfAd10AgmPortAddr | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.11.1.1.2 | ColumnrecfAd10AgmPortStartMode | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.11.1.1.3 | ColumnrecfAd10AgmPortUpdate | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.11.1.1.4 | ColumnrecfAd10AgmPortSpeed | read-write | mandatory | Parameter Type = Intrusive. The 19.2 kbps speed is not supported on SGM/AG modules with a hardware subtype of 1 or 3. The 56 kbps speed is not supported on SGM… |
| 1.3.6.1.4.1.16.101.1.2.1.11.1.1.5 | ColumnrecfAd10AgmPortDef | read-only | mandatory | Parameter Type = Internal. Defines AD-10 port usage. Each OCTET indicates an AD-10 port type. FF for not defined, 1 for data, 2 for voice and 3 for packet band. |
| 1.3.6.1.4.1.16.101.1.2.1.11.1.1.6 | ColumnrecfAd10AgmPortPartitionID | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.11.2 | TablerecfAd10DataPortTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.11.2.1 | RowrecfAd10DataPortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.11.2.1.1 | ColumnrecfAd10DataPortAddr | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.11.2.1.2 | ColumnrecfAd10DataPortStartMode | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.11.2.1.3 | ColumnrecfAd10DataPortUpdate | read-only | mandatory | Parameter Type = Internal. If set to resetReq, need to reset the AD-10 data port. |
| 1.3.6.1.4.1.16.101.1.2.1.11.2.1.4 | ColumnrecfAd10DataPortPhysSlot | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.11.2.1.5 | ColumnrecfAd10DataPortPhysPort | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.11.2.1.6 | ColumnrecfAd10DataPortTDMDataRate | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.11.2.1.7 | ColumnrecfAd10DataPortType | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.11.3 | TablerecfAd10VoicePortTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.11.3.1 | RowrecfAd10VoicePortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.11.3.1.1 | ColumnrecfAd10VoicePortAddr | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.11.3.1.2 | ColumnrecfAd10VoicePortStartMode | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.11.3.1.3 | ColumnrecfAd10VoicePortUpdate | read-only | mandatory | Parameter Type = Internal. If set to resetReq, need to reset the AD-10 voice port. |
| 1.3.6.1.4.1.16.101.1.2.1.11.3.1.4 | ColumnrecfAd10VoicePortPhysSlot | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.11.3.1.5 | ColumnrecfAd10VoicePortPhysPort | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.11.3.1.6 | ColumnrecfAd10VoicePortDBAMode | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.11.3.1.7 | ColumnrecfAd10VoicePortCompressMode | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.11.3.1.8 | ColumnrecfAd10VoicePortFaxMode | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.11.3.1.9 | ColumnrecfAd10VoicePortSpeed | read-write | mandatory | Parameter Type = Intrusive. The compressed channel data rate for this AD-10 voice port. For ports using a CELP compression algorithm, only speeds of 5.333 Kbps… |
| 1.3.6.1.4.1.16.101.1.2.1.11.4 | TablerecfAd10PktBandTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.11.4.1 | RowrecfAd10PktBandEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.11.4.1.1 | ColumnrecfAd10PktBandAddr | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.11.4.1.2 | ColumnrecfAd10PktBandStartMode | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.11.4.1.3 | ColumnrecfAd10PktBandUpdate | read-only | mandatory | Parameter Type = Internal. If set to resetReq, need to reset the AD-10 packet band. |
| 1.3.6.1.4.1.16.101.1.2.1.11.4.1.4 | ColumnrecfAd10PktBandBaudRate | read-write | mandatory | Parameter Type = Intrusive. If recfAd10PktBandDBAMode is enabled, then this attribute is ignored. In this case, the actual rate will be dynamically based on th… |
| 1.3.6.1.4.1.16.101.1.2.1.11.4.1.5 | ColumnrecfAd10PktBandDBAMode | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.11.5 | TablerecfAd10TrkGrpTable | not-accessible | mandatory | Trunk group entries in this table will map a single AD-10 trunk group address to multiple AD-10 port addresses. It is intended to provide port contention withi… |
| 1.3.6.1.4.1.16.101.1.2.1.11.5.1 | RowrecfAd10TrkGrpEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.11.5.1.1 | ColumnrecfAd10TrkGrpAddr | read-only | mandatory | Parameter Type = Internal. Address of the AD-10 trunk group. |
| 1.3.6.1.4.1.16.101.1.2.1.11.5.1.2 | ColumnrecfAd10TrkGrpStartMode | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. Erase will fail if there are any AD-10 channels connected that are usi… |
| 1.3.6.1.4.1.16.101.1.2.1.11.5.1.3 | ColumnrecfAd10TrkGrpAgmPort | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. Defines the AGM port that this AD-10 trunk group may be connected to. … |
| 1.3.6.1.4.1.16.101.1.2.1.11.5.1.4 | ColumnrecfAd10TrkGrpLowElement | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. The low end of the element range available for use by this AD-10 trunk… |
| 1.3.6.1.4.1.16.101.1.2.1.11.5.1.5 | ColumnrecfAd10TrkGrpHighElement | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. The high end of the element range available for use by this AD-10 trun… |
| 1.3.6.1.4.1.16.101.1.2.1.11.5.1.6 | ColumnrecfAd10TrkGrpRemoteNodeID | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. The node that any AD-10 subrate channel using this trunk group will co… |
| 1.3.6.1.4.1.16.101.1.2.1.11.5.1.7 | ColumnrecfAd10TrkGrpRemoteAddr | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. The trunk group used for the remote end of any AD-10 subrate channel u… |
| 1.3.6.1.4.1.16.101.1.2.1.11.5.1.8 | ColumnrecfAd10TrkGrpPartitionID | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. The partition ID of this trunk group. Used to enforce security on shar… |
| 1.3.6.1.4.1.16.101.1.2.1.11.5.1.9 | ColumnrecfAd10TrkGrpSearchDirection | read-write | mandatory | Parameter Type = Immediate. INTRODUCED 2.0.0 Indicates the search order within the range specified by recfAd10TrkGrpLowElement and recfAd10TrkGrpHighElement at… |
| 1.3.6.1.4.1.16.101.1.2.1.12 | NoderecfAsmPort | |||
| 1.3.6.1.4.1.16.101.1.2.1.12.1 | NoderecfAsmX50Table | |||
| 1.3.6.1.4.1.16.101.1.2.1.12.1.1 | TablerecfAsmX50PortTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.12.1.1.1 | RowrecfAsmX50PortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.12.1.1.1.1 | ColumnrecfAsmX50PortAddr | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.12.1.1.1.2 | ColumnrecfAsmX50PortStartMode | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.12.1.1.1.3 | ColumnrecfAsmX50PortUpdate | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.12.1.1.1.4 | ColumnrecfAsmX50PortSpeed | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.12.1.1.1.5 | ColumnrecfAsmX50PortProtocol | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.12.1.1.1.6 | ColumnrecfAsmX50PortIdlePattern | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.12.1.1.1.7 | ColumnrecfAsmX50PortOosTimer | read-write | mandatory | Parameter Type = Intrusive. Time before the port will go out-of-service. If disabled, port will never go OOS. |
| 1.3.6.1.4.1.16.101.1.2.1.12.1.1.1.8 | ColumnrecfAsmX50PortPhasorSize | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.12.1.1.1.9 | ColumnrecfAsmX50PortTxHouseKbits | read-write | mandatory | Parameter Type = Intrusive. The following is the map between bits in the bit map and housekeeping bits. bit 0 (lsb) - 'H' bit 1 - 'G' bit 2 - 'F' bit 3 - 'E' b… |
| 1.3.6.1.4.1.16.101.1.2.1.12.1.1.1.10 | ColumnrecfAsmX50PortCircuitMap | read-only | mandatory | Parameter Type = Internal. Each byte indicates the usage of the circuit on the X.50 aggregate. 1 is for defined, and 0xFF is for undefined. |
| 1.3.6.1.4.1.16.101.1.2.1.12.1.1.1.11 | ColumnrecfAsmX50PortPartitionID | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.12.1.2 | TablerecfAsmX50CkTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.12.1.2.1 | RowrecfAsmX50CkEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.12.1.2.1.1 | ColumnrecfAsmX50CkAddr | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.12.1.2.1.2 | ColumnrecfAsmX50CkStartMode | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.12.1.2.1.3 | ColumnrecfAsmX50CkUpdate | read-only | mandatory | Parameter Type = Internal. If set to resetReq, need to reset the ASM X.50 circuit. |
| 1.3.6.1.4.1.16.101.1.2.1.12.1.2.1.4 | ColumnrecfAsmX50CkSpeed | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.12.1.2.1.5 | ColumnrecfAsmX50CkTimeSlot | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.12.1.2.1.6 | ColumnrecfAsmX50CkPhasorSize | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.12.1.2.1.7 | ColumnrecfAsmX50CkSbitConnectState | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.12.2 | NoderecfAsmVoice | |||
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1 | TablerecfAsmVoiceTrkGrpTable | not-accessible | mandatory | Trunk group entries in this table will serve as a profile for multiple physical ASM ports. If intended to use as a non-contention system, then this trunk group… |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1 | RowrecfAsmVoiceTrkGrpEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.1 | ColumnrecfAsmVoiceTrkGrpAddr | read-only | mandatory | Parameter Type = Internal. Address of the voice trunk group. |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.2 | ColumnrecfAsmVoiceTrkGrpStartMode | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. Erase will fail if there are any voice channels connected that are usi… |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.3 | ColumnrecfAsmVoiceTrkGrpPort | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. Defines the T1M/E1M port that this voice trunk group may be connected … |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.4 | ColumnrecfAsmVoiceTrkGrpLowElement | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. The low end of the element range available for use by this Voice trunk… |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.5 | ColumnrecfAsmVoiceTrkGrpHighElement | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. The high end of the element range available for use by this voice trun… |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.6 | ColumnrecfAsmVoiceTrkGrpRemoteNodeID | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. The node that any voice subrate channel using this trunk group will co… |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.7 | ColumnrecfAsmVoiceTrkGrpRemoteAddr | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. The trunk group used for the remote end of any voice subrate channel u… |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.8 | ColumnrecfAsmVoiceTrkGrpPartitionID | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. The partition ID of this trunk group. Used to enforce security on shar… |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.9 | ColumnrecfAsmVoiceTrkGrpCompressMode | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. Defines which compression algorithm to use for voice channels connecte… |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.10 | ColumnrecfAsmVoiceTrkGrpSpeed | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. The compressed channel data rate for any voice subrate connections usi… |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.11 | ColumnrecfAsmVoiceTrkGrpSignalingType | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. The type of signaling used by the T1M/E1M bundles that connect to voic… |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.12 | ColumnrecfAsmVoiceTrkGrpDTMFRelay | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. Controls the DTMF relay on any ASM voice ports that use this trunk gro… |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.13 | ColumnrecfAsmVoiceTrkGrpFaxRelay | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. Controls the fax relay on any ASM voice ports that use this trunk grou… |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.14 | ColumnrecfAsmVoiceTrkGrpFaxNSFMode | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. Controls the non-standard fax mode on any ASM voice ports that use thi… |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.15 | ColumnrecfAsmVoiceTrkGrpTxAudSrcMode | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. Controls the transmit audio source on any ASM voice ports that use thi… |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.16 | ColumnrecfAsmVoiceTrkGrpRxAudOutMode | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. Controls the receive audio output on any ASM voice ports that use this… |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.17 | ColumnrecfAsmVoiceTrkGrpEchoCancel | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. Controls the echo cancellation on any ASM voice ports that use this tr… |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.18 | ColumnrecfAsmVoiceTrkGrpNonLinear | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. Controls the non-linear processing inside the echo canceller on any AS… |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.19 | ColumnrecfAsmVoiceTrkGrpDataMode | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. Controls the 2100 Hz detection logic and data mode operation with the … |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.20 | ColumnrecfAsmVoiceTrkGrpTxPCMGain | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. Controls the transmit PCM gain on any ASM voice ports that use this tr… |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.21 | ColumnrecfAsmVoiceTrkGrpRxPCMGain | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. Controls the receive PCM gain on any ASM voice ports that use this tru… |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.22 | ColumnrecfAsmVoiceTrkGrpVocoderEnable | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. Controls the vocoder mode on any ASM voice ports that use this trunk g… |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.23 | ColumnrecfAsmVoiceTrkGrpSigIdlePttrn | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. Defines the idle signaling pattern on any ASM voice ports that use thi… |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.24 | ColumnrecfAsmVoiceTrkGrpPCMPhasorSize | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. Size of the phasor (in bytes) on the PCM (64K) side of any ASM voice p… |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.25 | ColumnrecfAsmVoiceTrkGrpSubratePhSize | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. Size of the phasor (in bytes) on the subrate side of any ASM voice por… |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.26 | ColumnrecfAsmVoiceTrkGrpLocalSigConf | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. AD-10 and ASM signalling incompatibility parameters. |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.27 | ColumnrecfAsmVoiceTrkGrpRemoteSigConf | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. AD-10 and ASM signalling incompatibility parameters. |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.28 | ColumnrecfAsmVoiceTrkGrpRmtSigPattern | read-write | mandatory | Parameter Type = Immediate. Changes will not affect channels that are already connected. Defines the remote signaling pattern on any ASM voice ports that use t… |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.29 | ColumnrecfAsmVoiceTrkGrpCelpNetSigMd | read-write | mandatory | Parameter Type = Immediate. INTRODUCED 2.0.0 Enable autodetection of CELP/ATC channel connected equipment so as to automatically change format to become compat… |
| 1.3.6.1.4.1.16.101.1.2.1.12.2.1.1.30 | ColumnrecfAsmVoiceTrkGrpSearchDir | read-write | mandatory | Parameter Type = Immediate. INTRODUCED 2.0.0 Indicates the search order within the range specified by recfAsmVoiceTrkGrpLowElement and recfAsmVoiceTrkGrpHighEl… |
| 1.3.6.1.4.1.16.101.1.2.1.13 | NoderecfRtmPort | |||
| 1.3.6.1.4.1.16.101.1.2.1.13.1 | TablerecfRtmPortTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.13.1.1 | RowrecfRtmPortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.13.1.1.1 | ColumnrecfRtmPortAddr | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.13.1.1.2 | ColumnrecfRtmPortStartMode | read-write | mandatory | Parameter Type = Intrusive. Erase will reset all parameters to their default values. |
| 1.3.6.1.4.1.16.101.1.2.1.13.1.1.3 | ColumnrecfRtmPortUpdate | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.13.1.1.4 | ColumnrecfRtmPortType | read-write | mandatory | Parameter Type = Intrusive. Setting AD-3 or AD-7 will allocate all of the access device ports with their default parameters. |
| 1.3.6.1.4.1.16.101.1.2.1.13.1.1.5 | ColumnrecfRtmPortPartitionID | read-write | mandatory | Parameter Type = Intrusive. Default value is the partition ID of the node. |
| 1.3.6.1.4.1.16.101.1.2.1.13.2 | TablerecfRtmAdPortTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.13.2.1 | RowrecfRtmAdPortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.13.2.1.1 | ColumnrecfRtmAdPortAddr | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.13.2.1.2 | ColumnrecfRtmAdPortStartMode | read-write | mandatory | Parameter Type = Intrusive. Erase will reset all parameters to their default values. |
| 1.3.6.1.4.1.16.101.1.2.1.13.2.1.3 | ColumnrecfRtmAdPortUpdate | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.13.2.1.4 | ColumnrecfRtmAdPortSpeed | read-write | mandatory | Parameter Type = Intrusive. If the speed is set to s56000 and recfRtmAdPortDataBits attribute set to b7, the channel will be transported as a 64000 bit stuffed… |
| 1.3.6.1.4.1.16.101.1.2.1.13.2.1.5 | ColumnrecfRtmAdPortDataBits | read-write | mandatory | Parameter Type = Intrusive. Value b7 cannot be used in subrate connections. |
| 1.3.6.1.4.1.16.101.1.2.1.13.2.1.6 | ColumnrecfRtmAdPortCommMode | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.13.2.1.7 | ColumnrecfRtmAdPortType | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.14 | NoderecfLgmPort | |||
| 1.3.6.1.4.1.16.101.1.2.1.14.1 | TablerecfLgmPortTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.14.1.1 | RowrecfLgmPortEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.4.1.16.101.1.2.1.14.1.1.1 | ColumnrecfLgmPortAddr | read-only | mandatory | Parameter Type = Internal. This is a virtual port address in type:group:port format. |
| 1.3.6.1.4.1.16.101.1.2.1.14.1.1.2 | ColumnrecfLgmPortStartMode | read-write | mandatory | Parameter Type = Intrusive. Setting to erase will fail if the LGM port has any non-removed channels. If successful, returns the initial port configuration (wit… |
| 1.3.6.1.4.1.16.101.1.2.1.14.1.1.3 | ColumnrecfLgmPortUpdate | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.2.1.14.1.1.4 | ColumnrecfLgmPortArq | read-write | mandatory | Parameter Type = Intrusive. Specifies ARQ speed. Unit of bps, i which may not exceed the 9600. |
| 1.3.6.1.4.1.16.101.1.2.1.14.1.1.5 | ColumnrecfLgmPortGroup | read-write | mandatory | Parameter Type = Non-intrusive. Intended to force channels to use specific groups of LGM ports. There can be up to seven groups for each LGM port. Bit map bits… |
| 1.3.6.1.4.1.16.101.1.2.1.14.1.1.6 | ColumnrecfLgmPortEncryption | read-write | mandatory | Parameter Type = Non-intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.14.1.1.7 | ColumnrecfLgmPortSatelliteHop | read-write | mandatory | Parameter Type = Non-intrusive. Specifies the number of satellite hops per end - to - end point connection. Earth station - satellite - earth station connectio… |
| 1.3.6.1.4.1.16.101.1.2.1.14.1.1.8 | ColumnrecfLgmPortSyncChar | read-write | mandatory | Parameter Type = Intrusive. Specifies number of sync characters per frame. |
| 1.3.6.1.4.1.16.101.1.2.1.14.1.1.9 | ColumnrecfLgmPortSyncLevel | read-write | mandatory | Parameter Type = Intrusive. Synchronization level parameter. |
| 1.3.6.1.4.1.16.101.1.2.1.14.1.1.10 | ColumnrecfLgmPortOosTimer | read-write | mandatory | Parameter Type = Non-intrusive. In units of seconds. The Out-Of-Service state is entered if this time is exceeded. |
| 1.3.6.1.4.1.16.101.1.2.1.14.1.1.11 | ColumnrecfLgmPortPartitionID | read-write | mandatory | Parameter Type = Intrusive. Used by security server to enforce shared node. |
| 1.3.6.1.4.1.16.101.1.2.1.14.1.1.12 | ColumnrecfLgmPortBitMode | read-write | mandatory | Parameter Type = Intrusive. Defines the bit mode of this port. |
| 1.3.6.1.4.1.16.101.1.2.1.14.1.1.13 | ColumnrecfLgmPortInbandSuperrate | read-write | mandatory | Parameter Type = Non-intrusive. Specifies how the signaling function transport for inband superrate is handled. <nack> - reject a channel connection with a NO … |
| 1.3.6.1.4.1.16.101.1.2.1.14.1.1.14 | ColumnrecfLgmPortInbandSubrate | read-write | mandatory | Parameter Type = Non-intrusive. Specifies how the signaling function transport for inband subrate is handled. <nack> - reject a channel connection with a NO BA… |
| 1.3.6.1.4.1.16.101.1.2.1.14.1.1.15 | ColumnrecfLgmPortOutbandSuperrate | read-write | mandatory | Parameter Type = Non-intrusive. Specifies how the signaling function transport for outband superrate is handled. <nack> - reject a channel connection with a NO… |
| 1.3.6.1.4.1.16.101.1.2.1.14.1.1.16 | ColumnrecfLgmPortOutbandSubrate | read-write | mandatory | Parameter Type = Non-intrusive. Specifies how the signaling function transport for outband subrate is handled. <nack> - reject a channel connection with a NO B… |
| 1.3.6.1.4.1.16.101.1.2.1.15 | NoderecfDsmPort | |||
| 1.3.6.1.4.1.16.101.1.2.1.15.1 | TablerecfDsmIDCPortTable | not-accessible | mandatory | This section of the MIB is not changeable. It is included so that the user can verify the existance of PVC port. The user can configure frame relay channels on… |
| 1.3.6.1.4.1.16.101.1.2.1.15.1.1 | RowrecfDsmIDCPortEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.4.1.16.101.1.2.1.15.1.1.1 | ColumnrecfDsmIDCPortAddr | read-only | mandatory | Parameter Type = Internal. Port address format is nest.slot.65. |
| 1.3.6.1.4.1.16.101.1.2.1.15.2 | NoderecfDsmDChPort | |||
| 1.3.6.1.4.1.16.101.1.2.1.15.2.1 | TablerecfDsmDChPortTable | not-accessible | mandatory | This MIB section is used to configure D-channel virtual ports. The user can configure TDM channels on these ports in the recfTDMChannelEntry section of the MIB… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.1.1 | RowrecfDsmDChPortEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.1.1.1 | ColumnrecfDsmDChPortAddr | read-only | mandatory | Parameter Type = Internal. Port address format is type.group.port. The server type is 131. |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.1.1.2 | ColumnrecfDsmDChPortStartMode | read-write | mandatory | Parameter Type = Intrusive. If set to off, then the D-channel cannot be connected. In order to set to erase, the D-channel must be disconnected. |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.1.1.3 | ColumnrecfDsmDChPortUpdate | read-only | mandatory | Parameter Type = Internal. If set to resetReq, then the user must reset the port (which involves disconnecting and reconnecting the D-channel) in order for the… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.1.1.4 | ColumnrecfDsmDChPortPartitionID | read-write | mandatory | Parameter Type = Intrusive. Used for security on shared nodes. The default value is the partition ID of the node. |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.1.1.5 | ColumnrecfDsmDChPortPbxProtocol | read-write | mandatory | Parameter Type = Intrusive. Protocol used by the PBX using this D-channel. If the protocol type does not match the PBX protocol, then the port will not be able… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.1.1.6 | ColumnrecfDsmDChPortPbxLayer3Type | read-write | mandatory | Parameter Type = Intrusive. This parameter indicates whether the PBX or the DSM will be responsible for serving B-channels requests (layer 3 master or slave mo… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.1.1.7 | ColumnrecfDsmDChPortPbxLayer2Type | read-write | mandatory | Parameter Type = Intrusive. This parameter is independent of layer 3 master or slave mode. To function properly, the DSM and PBX should be configured as differ… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.1.1.8 | ColumnrecfDsmDChPortSharedZeroFlag | read-write | mandatory | Parameter Type = Intrusive. Indicates whether the zero bit of a frame's end flag can be combined with the zero bit of the next frame's start flag. |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.1.1.9 | ColumnrecfDsmDChPortEncodingType | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.1.1.10 | ColumnrecfDsmDChPortActiveLev1CDRMode | read-write | mandatory | Parameter Type = Non-intrusive. Specifies whether level 1 Call Detail Records for the calls in progress are to be collected for this D-channel. Changing this p… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.1.1.11 | ColumnrecfDsmDChPortRecordLev1CDRMode | read-write | mandatory | Parameter Type = Non-intrusive. Specifies whether level 1 Call Detail Records for the completed calls are to be collected for this D-channel. Changing this par… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.1.1.12 | ColumnrecfDsmDChPortActiveLev2CDRMode | read-write | mandatory | Parameter Type = Non-intrusive. Specifies whether level 2 Call Detail Records for the calls in progress are to be collected for this D-channel. Changing this p… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.1.1.13 | ColumnrecfDsmDChPortRecordLev2CDRMode | read-write | mandatory | Parameter Type = Non-intrusive. Specifies whether level 2 Call Detail Records for the completed calls are to be collected for this D-channel. Changing this par… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.1.1.14 | ColumnrecfDsmDChPortCallsPerSecond | read-write | mandatory | Parameter Type = Intrusive. This attribute is an estimate of the number of calls per second (in units of 0.01 calls per second) on this D-channel port. |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.2 | TablerecfDsmDChBChTable | not-accessible | mandatory | This MIB section is used to configure information about B-channels that are associated with the D-channel. |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.2.1 | RowrecfDsmDChBChEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.2.1.1 | ColumnrecfDsmDChBChAddr | read-only | mandatory | Parameter Type = Internal. Port address of associated D-channel port. The format is type.group.port. The server type is 131. |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.2.1.2 | ColumnrecfDsmDChBChBundle | read-only | mandatory | Parameter Type = Internal. Identifies the bundle which is associated with this D-channel port. |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.2.1.3 | ColumnrecfDsmDChBChDirection | read-write | mandatory | Parameter Type = Non-intrusive. Specifies the direction of the calls on this B-channel. The values are: - outgoing: allows calls originating on PBX to ST - inc… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.3 | TablerecfDsmDChExchTable | not-accessible | mandatory | This MIB section is used to assign up to 16 exchange codes to a D-channel. |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.3.1 | RowrecfDsmDChExchEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.3.1.1 | ColumnrecfDsmDChExchDChAddr | read-only | mandatory | Parameter Type = Internal. D-channel port address. The format is type.group.port. The server type is 131. |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.3.1.2 | ColumnrecfDsmDChExchIndex | read-only | mandatory | Parameter Type = Internal. Indexing the exchange code within this D-channel. |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.3.1.3 | ColumnrecfDsmDChExchControlMode | read-write | mandatory | Parameter Type = Non-intrusive. Indicates whether this exchange code may be used to make a call. The value erase is used to wipe out the existing exchange code… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.3.1.4 | ColumnrecfDsmDChExchCode | read-write | mandatory | Parameter Type = Non-intrusive. The valid characters are 0 - 9. Changes to this field will be reflected in recfDsmDChPortUpdate. A port update will be required… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.4 | TablerecfDsmDChQOSTable | not-accessible | mandatory | This MIB section specifies the source node quality of service resolution entry that is to be used for the channel connection. |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.4.1 | RowrecfDsmDChQOSEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.4.1.1 | ColumnrecfDsmDChQOSDChAddr | read-only | mandatory | Parameter Type = Internal. Address of D-channel, for which this entry is being used. |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.4.1.2 | ColumnrecfDsmDChQOSIndex | read-only | mandatory | Parameter Type = Internal. Index of the quality of service entry. |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.4.1.3 | ColumnrecfDsmDChQOSControlMode | read-write | mandatory | Parameter Type = Non-intrusive. Changes will not affect channels that are already connected. Disable will prevent this quality of service entry from being appl… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.4.1.4 | ColumnrecfDsmDChQOSLowBChan | read-write | mandatory | Parameter Type = Non-intrusive. The low end of the source bundle range available for use by this D-channel. If this attribute is set to 0, then the used value … |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.4.1.5 | ColumnrecfDsmDChQOSHighBChan | read-write | mandatory | Parameter Type = Non-intrusive. The high end of the source bundle range available for use by this D-channel. If this attribute is set to 0, then the used value… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.4.1.6 | ColumnrecfDsmDChQOSLowExchCode | read-write | mandatory | Parameter Type = Non-intrusive. The valid characters are 0 - 9. The low end of the destination exchange codes range. The comparison type used is based upon the… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.4.1.7 | ColumnrecfDsmDChQOSHighExchCode | read-write | mandatory | Parameter Type = Non-intrusive. The valid characters are 0 - 9. The high end of the destination exchange codes range. The comparison type used is based upon th… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.4.1.8 | ColumnrecfDsmDChQOSCallType | read-write | mandatory | Parameter Type = Non-intrusive. This attribute specifies the call type. Changes to this field will be reflected in recfDsmDChPortUpdate. A port update will be … |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.4.1.9 | ColumnrecfDsmDChQOSChPrfIndex | read-write | mandatory | Parameter Type = Non-intrusive. This attribute specifies the channel profile table index that is defined in the channel profile MIB section on the source node.… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.4.1.10 | ColumnrecfDsmDChQOSSpecialPrfIndex | read-write | mandatory | Parameter Type = Non-intrusive. This attribute specifies the special profile table index that is defined in the applicable profile MIB section on the source no… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.5 | TablerecfDsmDChDPNSSTable | not-accessible | mandatory | This MIB section is used to configure D-channel DPNSS protocol related attributes. |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.5.1 | RowrecfDsmDChDPNSSEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.5.1.1 | ColumnrecfDsmDChDPNSSAddr | read-only | mandatory | Parameter Type = Internal. D-channel port address. Format is type.group.port. The server type is 131. |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.5.1.2 | ColumnrecfDsmDChDPNSSNL | read-write | mandatory | Parameter Type = Intrusive. The minimum number of retransmissions of a command frame if no acknowledge received. Changes to this field will be reflected in rec… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.5.1.3 | ColumnrecfDsmDChDPNSSNT1 | read-write | mandatory | Parameter Type = Intrusive. Duration for which retransmission is done (in units of 10 milliseconds). Changes to this field will be reflected in recfDsmDChPortU… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.5.1.4 | ColumnrecfDsmDChDPNSSNT2 | read-write | mandatory | Parameter Type = Intrusive. Post retransmission acknowledge delay. In other words, this is an additional time after recfDsmDChDPNSSNL and recfDsmDChDPNSSNT1 ex… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.5.1.5 | ColumnrecfDsmDChDPNSSUnrecMsgIdle | read-write | mandatory | Parameter Type = Intrusive. If DSM has received unrecognized local PBX message, this setting specifies the idle time whithin which there will not be any outgoi… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.5.1.6 | ColumnrecfDsmDChDPNSSInterDgtTmr | read-write | mandatory | Parameter Type = Intrusive. Specifies the maximum time between PBX service request messages used to set up a call (in units of 1 second). If this time is excee… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.6 | TablerecfDsmDChQSigTable | not-accessible | mandatory | This MIB section is used to configure D-channel QSig protocol related attributes. |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.6.1 | RowrecfDsmDChQSigEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.6.1.1 | ColumnrecfDsmDChQSigAddr | read-only | mandatory | Parameter Type = Internal. D-channel port address. Format is type.group.port. The server type is 131. |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.6.1.2 | ColumnrecfDsmDChQSigK | read-write | mandatory | Parameter Type = Intrusive. Maximum number of outstanding (unacknowledged) I-frames. Changes to this field will be reflected in recfDsmDChPortUpdate. A port re… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.6.1.3 | ColumnrecfDsmDChQSigN200 | read-write | mandatory | Parameter Type = Intrusive. Maximum number of frame retransmissions. Changes to this field will be reflected in recfDsmDChPortUpdate. A port reset will be requ… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.6.1.4 | ColumnrecfDsmDChQSigT200 | read-write | mandatory | Parameter Type = Intrusive. Maximum time (in units of 1 second) before frame retransmission is initiated. Changes to this field will be reflected in recfDsmDCh… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.6.1.5 | ColumnrecfDsmDChQSigT203 | read-write | mandatory | Parameter Type = Intrusive. Maximum time (in units of 1 second) allowed on layer 2 without frame exchange. If no frame is sent during this time, then layer 2 m… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.6.1.6 | ColumnrecfDsmDChQSigT302 | read-write | mandatory | Parameter Type = Intrusive. Maximum time between PBX service request messages used to set up a call (in units of 1 second). If this time is exceeded then the c… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.6.1.7 | ColumnrecfDsmDChQSigT303 | read-write | mandatory | Parameter Type = Intrusive. SETUP message maximum response time (in units of 1 second). If exceeded, the SETUP messge will be sent once more. If there is still… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.6.1.8 | ColumnrecfDsmDChQSigT304 | read-write | mandatory | Parameter Type = Intrusive. Maximum time (in units of 1 second) after receipt of SETUP ACK before one of the following messages is received: CALL PROCEEDING, A… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.6.1.9 | ColumnrecfDsmDChQSigT305 | read-write | mandatory | Parameter Type = Intrusive. Maximum time (in units of 1 second) for DISCONNECT message response. Changes to this field will be reflected in recfDsmDChPortUpdat… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.6.1.10 | ColumnrecfDsmDChQSigT308 | read-write | mandatory | Parameter Type = Intrusive. Maximum time (in units of 1 second) for RELEASE message response. Changes to this field will be reflected in recfDsmDChPortUpdate. … |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.6.1.11 | ColumnrecfDsmDChQSigT309 | read-write | mandatory | Parameter Type = Intrusive. Maximum time (in units of 1 second) allowed to restore connection upon detection of a failure. If expired, both the connection and … |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.6.1.12 | ColumnrecfDsmDChQSigT314 | read-write | mandatory | Parameter Type = Intrusive. Maximum time (in units of 1 second) allowed to receive all of the segments of a message. This parameter applies only to segmented m… |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.6.1.13 | ColumnrecfDsmDChQSigT316 | read-write | mandatory | Parameter Type = Intrusive. Maximum time (in units of 1 second) for RESTART message response. Changes to this field will be reflected in recfDsmDChPortUpdate. … |
| 1.3.6.1.4.1.16.101.1.2.1.15.2.6.1.14 | ColumnrecfDsmDChQSigT322 | read-write | mandatory | Parameter Type = Intrusive. Maximum time (in units of 1 second) for STATUS INQUIRY message. Changes to this field will be reflected in recfDsmDChPortUpdate. A … |
| 1.3.6.1.4.1.16.101.1.2.1.16 | NoderecfTranslation | |||
| 1.3.6.1.4.1.16.101.1.2.1.16.1 | TablerecfLink2TraTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.1.16.1.1 | RowrecfLink2TraEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.4.1.16.101.1.2.1.16.1.1.1 | ColumnrecfLink2TraIndex | read-only | mandatory | Parameter Type = Internal. Translation table index, notated in Link-2 specific notation. Does not indicate any particular addresses, however must be set to the… |
| 1.3.6.1.4.1.16.101.1.2.1.16.1.1.2 | ColumnrecfLink2TraStartMode | read-write | mandatory | Parameter Type = Immediate. Setting to off will prevent this table entry from being used on connection (invalidates it). Setting to erase will free the entry. |
| 1.3.6.1.4.1.16.101.1.2.1.16.1.1.3 | ColumnrecfLink2TraStAddr | read-only | mandatory | Parameter Type = Immediate. Represents local ST-50 TDM channel Link2 channel (defined by recfLink2TraL2Addr attribute) is connected to. Used by ST-50 as a conn… |
| 1.3.6.1.4.1.16.101.1.2.1.16.1.1.4 | ColumnrecfLink2TraL2Addr | read-write | mandatory | Parameter Type = Immediate. Represents Link2 address in Link2 network ST-50 TDM channel (defined by recfLink2TraStAddr attribute) is connected to. If this attr… |
| 1.3.6.1.4.1.16.101.1.2.1.16.1.1.5 | ColumnrecfLink2TraFunctions | read-write | mandatory | Parameter Type = Immediate. Selects the mode of functions exchange. In inBand mode the same time slot as data is being used. In outBand it is a separate channe… |
| 1.3.6.1.4.1.16.101.1.2.1.16.1.1.6 | ColumnrecfLink2TraPartition | read-only | mandatory | Parameter Type = Internal. Displays the partition assigned to this translation table entry. This partition is inherited from the TDM channel associated with th… |
| 1.3.6.1.4.1.16.101.1.2.1.17 | NoderecfHwRsc | |||
| 1.3.6.1.4.1.16.101.1.2.1.17.1 | TablerecfHwRscEngineTable | not-accessible | mandatory | This MIB section is used for configuration of on-board engines on a module in an ST node. The engine configuration will be set up with default values when the … |
| 1.3.6.1.4.1.16.101.1.2.1.17.1.1 | RowrecfHwRscEngineEntry | not-accessible | mandatory | INTRODUCED 2.0.1 |
| 1.3.6.1.4.1.16.101.1.2.1.17.1.1.1 | ColumnrecfHwRscEngineModuleAddr | read-only | mandatory | The address of the module that this engine is located on. Format is <nest>.<slot>. |
| 1.3.6.1.4.1.16.101.1.2.1.17.1.1.2 | ColumnrecfHwRscEngineID | read-only | mandatory | The engine ID on the module. |
| 1.3.6.1.4.1.16.101.1.2.1.17.1.1.3 | ColumnrecfHwRscEngineStartMode | read-write | mandatory | Parameter Type = Intrusive. Controls whether the engine should start as inserted or removed when the module comes up. If the value is set to automatic, then th… |
| 1.3.6.1.4.1.16.101.1.2.1.17.1.1.4 | ColumnrecfHwRscEngineUpdate | read-only | mandatory | Indicates if the current settings in the engine configuration MIB represent the active settings on the module or not. If this value is resetRequired, then an e… |
| 1.3.6.1.4.1.16.101.1.2.1.17.1.1.5 | ColumnrecfHwRscEngineApplication | read-write | mandatory | Parameter Type = Intrusive. Used to reserve an engine for a specific application type. If no application type reservation is desired, then the value any should… |
| 1.3.6.1.4.1.16.101.1.2.1.17.1.1.6 | ColumnrecfHwRscEnginePartitionID | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.4.1.16.101.1.2.2 | NodereStatus | |||
| 1.3.6.1.4.1.16.101.1.2.2.1 | NoderestNode | |||
| 1.3.6.1.4.1.16.101.1.2.2.1.1 | NoderestNodeEntry | |||
| 1.3.6.1.4.1.16.101.1.2.2.1.1.1 | ScalarrestNodeDiagnostics | write-only | mandatory | updateNest will update the node with the new nest number. If the new nest number is greater than the old number, then the new nests will be added, and any modu… |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.2 | ScalarrestNodeStatus | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.3 | ScalarrestNodeCondition | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.4 | ScalarrestNodeSWRevision | read-only | mandatory | Version number of the NCP software that is currently running. |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.5 | ScalarrestNodeMIBRevision | read-only | mandatory | Version number of the MIB schema that the NCP is currently using. |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.6 | ScalarrestNodeUpTime | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.7 | ScalarrestNodeErrorMinutes | read-only | mandatory | Count of the error minutes in the bus for the past 24 hours. |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.8 | ScalarrestNodeNumOfNest | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.9 | ScalarrestNodePktBandBWAvail | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.10 | ScalarrestNodePktBandBWMax | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.11 | ScalarrestNodeMasterClockPriority | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.12 | ScalarrestNodeMasterClockMsg | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.13 | ScalarrestNodeClockTableIndex | read-only | mandatory | Indicates which clock in the clock fallback table is in use. If the clock status is slave holdover, then this field may return zero. |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.14 | ScalarrestNodeClockStatus | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.15 | ScalarrestNodeClockSubStatus | read-only | mandatory | These are the substates associated with slaveHoldover state. If the clock status is not slaveHoldover, then notApplicable will be returned. |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.16 | ScalarrestNodeClockSourceType | read-only | mandatory | Type of the clock currently in use. If the clock status is slave holdover, then this field may return not applicable. |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.17 | ScalarrestNodeClockSourcePort | read-only | mandatory | Source port address of the clock currently in use, if the clock type is portRxInd, portRxDep, or portTx. If the clock type is a different value, then this fiel… |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.18 | ScalarrestNodeClockSourcePriority | read-only | mandatory | Priority of the clock currently in use. If the clock status is slave holdover, then this field may return zero. |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.19 | ScalarrestNodeClockSourceQuality | read-only | mandatory | Quality of the clock currently in use. If the clock status is slave holdover, then this field may return not applicable. |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.20 | ScalarrestNodeClockQualifierStatus | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.21 | ScalarrestNodeTestGenStatus | read-only | mandatory | Current status of the test generator for TDM nDS0 channels. |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.22 | ScalarrestNodeTestGenType | read-only | mandatory | Current type of the test generator for TDM nDS0 channels. |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.23 | ScalarrestNodeTestGenTDMChannel | read-write | mandatory | Current channel address that the TDM test generator is being used on. |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.24 | ScalarrestNodeAlarmRelayStatus | read-only | mandatory | Indicates whether the alarm relay port is programmed to be used or not. |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.25 | ScalarrestNodeAlarmRelaySubStatus | read-only | mandatory | Indicates the status of the major alarm relay (first value) and the minor alarm relay (second value). This field is only valid if the alarm relay is enabled. |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.26 | ScalarrestNodeCpiStatus | read-only | mandatory | Indicates the current status of the CPI port. |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.27 | ScalarrestNodeModemStatus | read-only | mandatory | Indicates the current status of the modem port. |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.28 | ScalarrestNodeSoftloadStatus | read-only | mandatory | Indicates the softload status. 'Idle' means that no softload has been run yet since the node went online. 'Softloading' indicates that a download is underway f… |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.29 | ScalarrestNodeSoftloadTotal | read-only | mandatory | Total number of bytes to be softloaded. If no softloading is in progress, then this value is zero. |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.30 | ScalarrestNodeSoftloadSize | read-only | mandatory | Number of bytes that have been softloaded. Divide this by the value of restNodeSoftloadTotal to determine the completion percentage. If no softloading is in pr… |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.31 | ScalarrestNodeSoftloadSoftwareType | read-only | mandatory | Indicates type of software being transferred if a softload is in progress. notApplicable will be returned if no softload is in progress. |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.32 | ScalarrestNodeUploadStatus | read-only | mandatory | Each upload client, which is used to upload files to SNMS or to other nodes, is represented by one octet. There are a maximum of eight upload clients per ST no… |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.33 | ScalarrestNodeUploadTotal | read-only | mandatory | Total number of bytes to be uploaded to ech of up to eight clients. Each client uses four bytes for its value. If no uploading is in progress, then the value f… |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.34 | ScalarrestNodeUploadSize | read-only | mandatory | Number of bytes that have been uploaded to each of up to eight clients. Each client uses four bytes for its value. Divide each client's value in this field by … |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.35 | ScalarrestNodeUploadClientID | read-only | mandatory | Specifies the node numbers of the eight clients that this node is serving during an upload. Each client is identified by two bytes. If the client is an EMS, th… |
| 1.3.6.1.4.1.16.101.1.2.2.1.1.36 | ScalarrestNodeTotalDsmCallsPerSecond | read-only | mandatory | This is the total amount of calls per second (in units of 0.01 calls per second) allocated for DSM in this node. |
| 1.3.6.1.4.1.16.101.1.2.2.2 | TablerestNestTable | not-accessible | mandatory | This section of the MIB does not support getNext. |
| 1.3.6.1.4.1.16.101.1.2.2.2.1 | RowrestNestEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.2.1.1 | ColumnrestNestAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.2.1.2 | ColumnrestNestDiagnostics | write-only | mandatory | Remove will logically remove all of the modules in the nest, except the NCP, LXM, and RXM. This will free up the bus bandwidth. The configuration start mode of… |
| 1.3.6.1.4.1.16.101.1.2.2.2.1.3 | ColumnrestNestStatus | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.2.1.4 | ColumnrestNestCondition | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.2.1.5 | ColumnrestNestNumberOfModules | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.2.1.6 | ColumnrestNestPowerStatus | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.2.1.7 | ColumnrestNestFanStatus | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.2.1.8 | ColumnrestNestTemperature | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.2.1.9 | ColumnrestNestClockReference1 | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.2.1.10 | ColumnrestNestClockReference2 | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.2.1.11 | ColumnrestNestBusLoopbackStatus | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.2.1.12 | ColumnrestNestSlotPresence | read-only | mandatory | The lsb of the second octet represents slot 1, and the msb of the first octet represents slot 16. Slot 17 always has an RXM. Each bit set to 1 indicates that a… |
| 1.3.6.1.4.1.16.101.1.2.2.2.1.13 | ColumnrestNestActiveRight | read-only | mandatory | RXM status. |
| 1.3.6.1.4.1.16.101.1.2.2.2.1.14 | ColumnrestNestActiveLeft | read-only | mandatory | LXM status. |
| 1.3.6.1.4.1.16.101.1.2.2.2.1.15 | ColumnrestNestRxmCkt1Status | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.2.1.16 | ColumnrestNestRxmCkt2Status | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.2.1.17 | ColumnrestNestLxmCkt1Status | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.2.1.18 | ColumnrestNestLxmCkt2Status | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.3 | TablerestSlotTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.3.1 | RowrestSlotEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.3.1.1 | ColumnrestSlotAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.3.1.2 | ColumnrestSlotModuleDiagnostics | write-only | mandatory | Remove will free bus bandwidth used by the ports of the module, and set the module start mode in the configuration MIB to off. Insert on a removed module will … |
| 1.3.6.1.4.1.16.101.1.2.2.3.1.3 | ColumnrestSlotModuleStatus | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.3.1.4 | ColumnrestSlotModuleFailureType | read-only | mandatory | If module status is fail, indicates what type of failure occurred. notApplicable will be returned if the module status is not fail. noRTS means that the module… |
| 1.3.6.1.4.1.16.101.1.2.2.3.1.5 | ColumnrestSlotModuleCondition | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.3.1.6 | ColumnrestSlotSWModuleType | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.3.1.7 | ColumnrestSlotSWModuleSubType | read-only | mandatory | All the subtypes are defined in recfSlotModuleSubType entry. |
| 1.3.6.1.4.1.16.101.1.2.2.3.1.8 | ColumnrestSlotModuleIDFormat | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.3.1.9 | ColumnrestSlotHWModuleType | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.3.1.10 | ColumnrestSlotHWModuleSubType | read-only | mandatory | All the subtypes are defined in recfSlotModuleSubType entry. |
| 1.3.6.1.4.1.16.101.1.2.2.3.1.11 | ColumnrestSlotModuleAssemblyNum | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.3.1.12 | ColumnrestSlotModuleRevision | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.3.1.13 | ColumnrestSlotModuleSerialNum | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.3.1.14 | ColumnrestSlotModuleDateMade | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.3.1.15 | ColumnrestSlotActiveRedundantSlot | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.3.1.16 | ColumnrestSlotModuleSWRevision | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.3.1.17 | ColumnrestSlotStartupDiagResults | read-only | mandatory | Each bit displays the result (pass/fail) of a startup diagnostic. The bit map for the first four bytes is defined in recfSlotModuleStartDiagMask. The bit map f… |
| 1.3.6.1.4.1.16.101.1.2.2.3.1.18 | ColumnrestSlotBGDiagResults | read-only | mandatory | Each bit displays the result (pass/fail) of a background diagnostic. The bit map for the first four bytes is defined in recfSlotModuleBgdDiagMask. The bit map … |
| 1.3.6.1.4.1.16.101.1.2.2.3.1.19 | ColumnrestSlotNumActivePorts | read-only | mandatory | INTRODUCED 2.0.0 Number of ports on this module that have a restPortStatus value of active. |
| 1.3.6.1.4.1.16.101.1.2.2.3.1.20 | ColumnrestSlotNumNormalPorts | read-only | mandatory | INTRODUCED 2.0.0 Number of ports on this module that have a restPortCondition value of normal. |
| 1.3.6.1.4.1.16.101.1.2.2.4 | NoderestModule | |||
| 1.3.6.1.4.1.16.101.1.2.2.4.1 | TablerestNcpTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.4.1.1 | RowrestNcpEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.4.1.1.1 | ColumnrestNcpAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.4.1.1.2 | ColumnrestNcpBootPromRevision | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.4.1.1.3 | ColumnrestNcpMacAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.4.1.1.4 | ColumnrestNcpFlashObjectVersions | read-only | deprecated | DEPRECATED 2.0.1 The information in this attribute has been replaced by the restNcpFlashTable section of the MIB. For each module type whose run-time software … |
| 1.3.6.1.4.1.16.101.1.2.2.4.2 | TablerestNcpFlashTable | not-accessible | mandatory | This MIB section lists all of the module object files stored in the flash PROM of the specified NCP. This section of the MIB does not support getNext. If the f… |
| 1.3.6.1.4.1.16.101.1.2.2.4.2.1 | RowrestNcpFlashEntry | not-accessible | mandatory | INTRODUCED 2.0.1 |
| 1.3.6.1.4.1.16.101.1.2.2.4.2.1.1 | ColumnrestNcpFlashAddr | read-only | mandatory | The address of the NCP. |
| 1.3.6.1.4.1.16.101.1.2.2.4.2.1.2 | ColumnrestNcpFlashIndex | read-only | mandatory | Used to differentiate the different module object files in the NCP flash PROM. This attribute does not contain any information about the file in flash. |
| 1.3.6.1.4.1.16.101.1.2.2.4.2.1.3 | ColumnrestNcpFlashModuleType | read-only | mandatory | The module type of this object file. |
| 1.3.6.1.4.1.16.101.1.2.2.4.2.1.4 | ColumnrestNcpFlashRecoveryIndicator | read-only | mandatory | Indicates whether or not this object file is stored in the softload recovery area. |
| 1.3.6.1.4.1.16.101.1.2.2.4.2.1.5 | ColumnrestNcpFlashCompressIndicator | read-only | mandatory | Indicates whether or not this object file is compressed or uncompressed. |
| 1.3.6.1.4.1.16.101.1.2.2.4.2.1.6 | ColumnrestNcpFlashFileVersionNumber | read-only | mandatory | The software revision number of this module object file. |
| 1.3.6.1.4.1.16.101.1.2.2.4.2.1.7 | ColumnrestNcpFlashFileSize | read-only | mandatory | The size of this module object file in bytes. |
| 1.3.6.1.4.1.16.101.1.2.2.4.2.1.8 | ColumnrestNcpFlashFileStoredCrc | read-only | mandatory | The stored CRC of this module object file. |
| 1.3.6.1.4.1.16.101.1.2.2.4.2.1.9 | ColumnrestNcpFlashFileCrcCheck | read-only | mandatory | If pass is returned, then the file image in flash passed a CRC check. If fail is returned, then the CRC check failed and the file is corrupted. If not applicab… |
| 1.3.6.1.4.1.16.101.1.2.2.4.6 | TablerestFsmTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.4.6.1 | RowrestFsmEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.4.6.1.1 | ColumnrestFsmAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.4.6.1.2 | ColumnrestFsmBypassBandwidth | read-only | mandatory | Maximum available bypass capability in units of packets. Bypass capability is also limited by restFsmBandwidthAvail. |
| 1.3.6.1.4.1.16.101.1.2.2.4.6.1.3 | ColumnrestFsmSourceBandwidth | read-only | mandatory | Maximum available termination capability in units of packets. Termination capability also limited by restFsmBandwidthAvail. |
| 1.3.6.1.4.1.16.101.1.2.2.4.6.1.4 | ColumnrestFsmBandwidthAvail | read-only | mandatory | FSM available processing capability to serve new termination or bypass channel, in units of packets. This may be less than the sum of restFsmBypassBandwidth an… |
| 1.3.6.1.4.1.16.101.1.2.2.4.6.1.5 | ColumnrestFsmPortSpeedAvail | read-only | mandatory | FSM available port speed capability in units of bps. This only indicates the capability to support termination channels. |
| 1.3.6.1.4.1.16.101.1.2.2.4.6.1.6 | ColumnrestFsmDlciTotal | read-only | mandatory | Total number of DLCIs permitted on this FSM module. |
| 1.3.6.1.4.1.16.101.1.2.2.4.6.1.7 | ColumnrestFsmDlciAvail | read-only | mandatory | Number of DLCIs that can still be connected on this FSM module. The number of DLCIs that are connected on the module can be determined by subtracting this valu… |
| 1.3.6.1.4.1.16.101.1.2.2.4.6.1.8 | ColumnrestFsmDlciConfig | read-only | mandatory | Number of DLCIs that are configured on frame relay ports allocated to this FSM module. A new FSM port cannot be allocated on this module if the number of DLCIs… |
| 1.3.6.1.4.1.16.101.1.2.2.4.6.1.9 | ColumnrestFsmBypChanTotal | read-only | mandatory | Total number of bypass channels permitted on this FSM module. |
| 1.3.6.1.4.1.16.101.1.2.2.4.6.1.10 | ColumnrestFsmBypChanAvail | read-only | mandatory | Number of bypass channels that can still be connected on this FSM module. The number of bypass channels that are connected on the module can be determined by s… |
| 1.3.6.1.4.1.16.101.1.2.2.4.6.1.11 | ColumnrestFsmCirTotal | read-only | mandatory | Total CIR on FSM module. |
| 1.3.6.1.4.1.16.101.1.2.2.4.6.1.12 | ColumnrestFsmCirAvail | read-only | mandatory | Available (unused) CIR on FSM module. |
| 1.3.6.1.4.1.16.101.1.2.2.4.6.1.13 | ColumnrestFsmVciCtrlBlkTotal | read-only | mandatory | Total number of Vci Control Blocks allowed on FSM module. Each DLCI terminated on the module requires one Vci Control Block. Each bypass channel on the module … |
| 1.3.6.1.4.1.16.101.1.2.2.4.6.1.14 | ColumnrestFsmVciCtrlBlkAvail | read-only | mandatory | Number of available (unused) PVCs on FSM module. Each DLCI terminated on the module requires one Vci Control Block. Each bypass channel on the module requires … |
| 1.3.6.1.4.1.16.101.1.2.2.4.6.1.15 | ColumnrestFsmTotalBuffers | read-only | mandatory | Total number of channel buffers on FSM module. |
| 1.3.6.1.4.1.16.101.1.2.2.4.6.1.16 | ColumnrestFsmBuffersAvail | read-only | mandatory | Number of available (unused) channel buffers on FSM module. |
| 1.3.6.1.4.1.16.101.1.2.2.4.6.1.17 | ColumnrestFsmCcfSupportIndicator | read-only | mandatory | INTRODUCED 2.1.0 Indicates whether or not this module is capable of supporting CCFs. |
| 1.3.6.1.4.1.16.101.1.2.2.4.7 | TablerestSgmAgTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.4.7.1 | RowrestSgmAgEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.4.7.1.1 | ColumnrestSgmAgAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.4.7.1.2 | ColumnrestSgmAgmPortAvail | read-only | mandatory | Number of AGM ports that are available for use on this SGM/AG module. |
| 1.3.6.1.4.1.16.101.1.2.2.4.7.1.3 | ColumnrestSgmAgmPortTotal | read-only | mandatory | Total number of AGM ports that are on this SGM/AG module. |
| 1.3.6.1.4.1.16.101.1.2.2.4.7.1.4 | ColumnrestSgmAgSafAvail | read-only | mandatory | Number of SAF ports that are available for use on this SGM/AG module. |
| 1.3.6.1.4.1.16.101.1.2.2.4.7.1.5 | ColumnrestSgmAgSafTotal | read-only | mandatory | Total number of SAF ports that are on this SGM/AG module. |
| 1.3.6.1.4.1.16.101.1.2.2.4.7.1.6 | ColumnrestSgmAgSgmScfAvail | read-only | mandatory | Number of SGM SCF ports that are available for use on this SGM/AG module. If the software type of the module is AGM, then zero shall be returned. |
| 1.3.6.1.4.1.16.101.1.2.2.4.7.1.7 | ColumnrestSgmAgSgmScfTotal | read-only | mandatory | Total number of SGM SCF ports that are on this SGM/AG module. If the software type of the module is AGM, then zero shall be returned. |
| 1.3.6.1.4.1.16.101.1.2.2.4.7.1.8 | ColumnrestSgmAgAgmScfAvail | read-only | mandatory | Number of AGM SCF ports that are available for use on this SGM/AG module. This value is valid for both SGM and AGM module software types. |
| 1.3.6.1.4.1.16.101.1.2.2.4.7.1.9 | ColumnrestSgmAgAgmScfTotal | read-only | mandatory | Total number of AGM SCF ports that are on this SGM/AG module. This value is valid for both SGM and AGM module software types. |
| 1.3.6.1.4.1.16.101.1.2.2.4.7.1.10 | ColumnrestSgmAgAgmCcfAvail | read-only | mandatory | INTRODUCED 2.1.0 Number of AGM CCF ports that are available for use on this SGM/AG module. This value is valid for both SGM and AGM module software types. |
| 1.3.6.1.4.1.16.101.1.2.2.4.7.1.11 | ColumnrestSgmAgAgmCcfTotal | read-only | mandatory | INTRODUCED 2.1.0 Total number of AGM CCF ports that are on this SGM/AG module. This value is valid for both SGM and AGM module software types. |
| 1.3.6.1.4.1.16.101.1.2.2.4.7.1.12 | ColumnrestSgmAgAgmPortCapacity | read-only | mandatory | INTRODUCED 2.1.0 List of AGM port speeds that are supported by this SGM/AG module. Every 4 bytes indicates one speed. The following speeds are supported: 19200… |
| 1.3.6.1.4.1.16.101.1.2.2.4.8 | NoderestAsm | |||
| 1.3.6.1.4.1.16.101.1.2.2.4.8.1 | TablerestAsmModuleTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.1.1 | RowrestAsmModuleEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.1.1.1 | ColumnrestAsmModuleAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.1.1.2 | ColumnrestAsmModuleMaxCelp | read-only | deprecated | Indicates the number of CELP licenses on the module. |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.1.1.3 | ColumnrestAsmModuleNumCelpAvail | read-only | deprecated | Indicates the number of CELP licenses on the module that are not in use. |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.1.1.4 | ColumnrestAsmModuleTotalEngines | read-only | mandatory | Indicates the total number of DSP engines on the module. |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.1.1.5 | ColumnrestAsmModuleAvailEngines | read-only | mandatory | Indicates the currently available (unused) number of DSP engines on the module. |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.1.1.6 | ColumnrestAsmModuleTotalSafScfs | read-only | mandatory | Indicates the total number of SAFs and SCFs that can be allocated on this ASM module. |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.1.1.7 | ColumnrestAsmModuleAvailSafScfs | read-only | mandatory | Indicates the currently available (unused) number of SAFs and SCFs on this ASM module. |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.2 | TablerestAsmEngineTable | not-accessible | deprecated | This section of the MIB doesn't support getNext |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.2.1 | RowrestAsmEngineEntry | not-accessible | deprecated | |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.2.1.1 | ColumnrestAsmEngineModuleAddr | read-only | deprecated | Physical address of the ASM module |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.2.1.2 | ColumnrestAsmEngineID | read-only | deprecated | The engine ID on ASM module |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.2.1.3 | ColumnrestAsmEngineDiagnostics | not-accessible | deprecated | Not used yet |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.2.1.4 | ColumnrestAsmEngineStatus | read-only | deprecated | These applications cannot be on the same engine at the same time |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.2.1.5 | ColumnrestAsmEngineNumPorts | read-only | deprecated | Number of application ports |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.2.1.6 | ColumnrestAsmEngineNumSAFs | read-only | deprecated | Number of SAF ports. If none returns zero |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.2.1.7 | ColumnrestAsmEngineNumSCFs | read-only | deprecated | Number of SCF ports. If none returns zero |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.2.1.8 | ColumnrestAsmEngineApplication | read-only | deprecated | Indicates the type of application allocated on this DSP engine, if any. |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.3 | TablerestAsmModApplTable | not-accessible | mandatory | This section of the MIB enables the user to determine the availability of specific resource types on an ASM module based upon the current resource allocation. … |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.3.1 | RowrestAsmModApplEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.3.1.1 | ColumnrestAsmModApplModuleAddr | read-only | mandatory | Physical address of the ASM module |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.3.1.2 | ColumnrestAsmModApplType | read-only | mandatory | The ASM application type. |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.3.1.3 | ColumnrestAsmModApplMaxPortsAllowed | read-only | mandatory | The maximum number of ports which can be allocated on the ASM module running the specified application. This value assumes that the module is running no other … |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.3.1.4 | ColumnrestAsmModApplCurPortsAllowed | read-only | mandatory | The current number of ports which can be allocated on the ASM module running the specified application. This determines how many ports can still be allocated b… |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.3.1.5 | ColumnrestAsmModApplCurPortsAllocated | read-only | mandatory | The current number of ports which are allocated on the ASM module and are running the specified application. |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.3.1.6 | ColumnrestAsmModApplEnginesUsed | read-only | mandatory | The total number of DSP engines on the ASM module that are currently allocated for this application type. |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.3.1.7 | ColumnrestAsmModApplEnginesRsvd | read-only | mandatory | The total number of unallocated DSP engines on the ASM module that are reserved for this application type. |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.3.1.8 | ColumnrestAsmModApplTotalLicenses | read-only | mandatory | The total number of licenses available on the ASM module for this application type. If the application is unlicensed, then a value of zero shall be returned. |
| 1.3.6.1.4.1.16.101.1.2.2.4.8.3.1.9 | ColumnrestAsmModApplAvailLicenses | read-only | mandatory | A count of the licenses on the ASM module for this application type which are not currently in use. If the application is unlicensed, then a value of zero shal… |
| 1.3.6.1.4.1.16.101.1.2.2.4.9 | NoderestRtm | |||
| 1.3.6.1.4.1.16.101.1.2.2.4.9.1 | TablerestRtmModuleTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.4.9.1.1 | RowrestRtmModuleEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.4.9.1.1.1 | ColumnrestRtmModuleAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.4.9.1.1.2 | ColumnrestRtmModuleDS0sUsed | read-only | mandatory | Current number of DS0 connections from AD-x units on this module. |
| 1.3.6.1.4.1.16.101.1.2.2.4.9.1.1.3 | ColumnrestRtmModuleDS0sAvail | read-only | mandatory | With the current number of DS0 and SAF connections, this field specifies the number of DS0 connections that could still be made assuming no more SAF connection… |
| 1.3.6.1.4.1.16.101.1.2.2.4.9.1.1.4 | ColumnrestRtmModuleSafsUsed | read-only | mandatory | Current number of SAF connections from AD-x units on this module. |
| 1.3.6.1.4.1.16.101.1.2.2.4.9.1.1.5 | ColumnrestRtmModuleSafsAvail | read-only | mandatory | With the current number of DS0 and SAF connections, this field specifies the number of SAF connections that could still be made assuming no more DS0 connection… |
| 1.3.6.1.4.1.16.101.1.2.2.4.10 | NoderestDsmModule | |||
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1 | TablerestDsmModuleTable | not-accessible | mandatory | This section of the MIB is used to get status of any DSM modules defined on the node. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1.1 | RowrestDsmModuleEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1.1.1 | ColumnrestDsmModuleAddr | read-only | mandatory | Address of this DSM module. Format is nest.slot. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1.1.2 | ColumnrestDsmModuleNumDsmComms | read-only | mandatory | Number of DSMs that this DSM is able to communicate with. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1.1.3 | ColumnrestDsmModuleNumCallsProc | read-only | mandatory | Number of calls in the non-idle state (in the process of connection, connected or in the process of disconnection). |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1.1.4 | ColumnrestDsmModuleNumRmtRteEntries | read-only | mandatory | Total number of entries allowed in the remote routing table. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1.1.5 | ColumnrestDsmModuleNumRmtRteAvail | read-only | mandatory | Number of entries in the remote routing table that are available. The number of occupied entries can be determined by subtracting this value from restDsmModule… |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1.1.6 | ColumnrestDsmModuleNumLocRteEntries | read-only | mandatory | Total number of entries allowed in the local routing table. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1.1.7 | ColumnrestDsmModuleNumLocRteAvail | read-only | mandatory | Number of entries in the local routing table that are available. The number of occupied entries can be determined by subtracting this value from restDsmModuleN… |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1.1.8 | ColumnrestDsmModuleBypassPPSTotal | read-only | mandatory | Total bypass throughput allowed on this DSM module in units of packets per second. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1.1.9 | ColumnrestDsmModuleBypassPPSAvail | read-only | mandatory | Available bypass capability in units of packets per second. The currently being used bypass throughput on the module can be determined by subtracting this valu… |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1.1.10 | ColumnrestDsmModuleBypChanTotal | read-only | mandatory | Total number of bypass channels permitted on this DSM module. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1.1.11 | ColumnrestDsmModuleBypChanAvail | read-only | mandatory | Number of bypass channels that can still be connected on this DSM module. The number of bypass channels that are connected on the module can be determined by s… |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1.1.12 | ColumnrestDsmModuleCirTotal | read-only | mandatory | Total CIR on this DSM module. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1.1.13 | ColumnrestDsmModuleCirAvail | read-only | mandatory | Available (unused) CIR on this DSM module. The currently being used CIR can be determined by subtracting this value from restDsmModuleBypChanTotal. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1.1.14 | ColumnrestDsmModuleVciCtrlBlkTotal | read-only | mandatory | Total number of Vci Control Blocks allowed on this DSM module. Each DLCI terminated on the module requires one Vci Control Block. Each bypass channel on the mo… |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1.1.15 | ColumnrestDsmModuleVciCtrlBlkAvail | read-only | mandatory | Number of available (unused) PVCs on this DSM module. Each DLCI terminated on the module requires one Vci Control Block. Each bypass channel on the module requ… |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1.1.16 | ColumnrestDsmModuleTotalBuffers | read-only | mandatory | Total number of channel buffers allowed on this DSM module. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1.1.17 | ColumnrestDsmModuleBuffersAvail | read-only | mandatory | Number of available (unused) channel buffers on DSM module. The number of channel buffers that are currently being used on the module can be determined by subt… |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1.1.18 | ColumnrestDsmModuleTotalRecCDRs | read-only | mandatory | Total number of recorded CDRs allowed on this DSM module. This value is counted across all CDR logs |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1.1.19 | ColumnrestDsmModuleRecCDRsAvail | read-only | mandatory | Number of available (unused) CDRs on this DSM module. These CDRs may be assigned to any of the CDR logs defined on this DSM module. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1.1.20 | ColumnrestDsmModuleTotalCallsPerSec | read-only | mandatory | This is the total amount of calls per second (in units of 0.01 calls per second) that can be handled by this DSM. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1.1.21 | ColumnrestDsmModuleCallsPerSecAvail | read-only | mandatory | This is the amount of calls per second (in units of 0.01 calls per second) that can be allocated on this DSM. The number of calls per second currently allocate… |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1.1.22 | ColumnrestDsmModuleCallsPerSecFactor | read-only | mandatory | This is the conversion factor between calls per second (in units of 0.01 calls per second) and processing units. The equation is: processing units = this value… |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1.1.23 | ColumnrestDsmModuleBypassFactor | read-only | mandatory | This is the conversion factor between bypass bandwidth (in PPS) and processing units. The equation is: processing units = this value * bypass bandwidth. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1.1.24 | ColumnrestDsmModuleTotalProcessUnits | read-only | mandatory | This is a rating for the total number of D-channel calls per second and bypass bandwidth allowed on this DSM. The two quantities are converted to the same unit… |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.1.1.25 | ColumnrestDsmModuleProcessUnitsAvail | read-only | mandatory | This is a rating of the number of the number of D-channel calls per second and bypass bandwidth that is unused on this DSM. To determine the amount that is cur… |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.2 | TablerestDsmModRecCDRLogTable | not-accessible | mandatory | This section of the MIB specifies status of the Call Detail Record log for completed calls. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.2.1 | RowrestDsmModRecCDRLogEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.2.1.1 | ColumnrestDsmModRecCDRLogAddr | read-only | mandatory | Address of this DSM module. Format is nest.slot. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.2.1.2 | ColumnrestDsmModRecCDRLogIndex | read-only | mandatory | CDR log number on this DSM module. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.2.1.3 | ColumnrestDsmModRecCDRLogStatus | read-only | mandatory | This CDR log overflow flag status. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.2.1.4 | ColumnrestDsmModRecCDRLogLev1Entries | read-only | mandatory | Number of level 1 CDRs for this CDR log. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.2.1.5 | ColumnrestDsmModRecCDRLogLev2Entries | read-only | mandatory | Number of level 2 CDRs for this CDR log. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.2.1.6 | ColumnrestDsmModRecCDRLogClrEntries | write-only | mandatory | Number of entries on this CDR log to be cleared, counting from the oldest record. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.3 | TablerestDsmModRecCDRTable | not-accessible | mandatory | This section of the MIB contains the status of a Call Detail Records for completed call. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.3.1 | RowrestDsmModRecCDREntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.3.1.1 | ColumnrestDsmModRecCDRAddr | read-only | mandatory | Address of this DSM module. Format is nest.slot. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.3.1.2 | ColumnrestDsmModRecCDRLogNum | read-only | mandatory | Specifies the CDR log number to be accessed on this DSM module. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.3.1.3 | ColumnrestDsmModRecCDRIndex | read-only | mandatory | Identifies the Call Detail Record to be accessed on this log based on its position (counting from the oldest one). |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.3.1.4 | ColumnrestDsmModRecCDRContents | read-only | mandatory | Call Detail Record from a module CDR log. These CDRs are for completed calls. The bytes in a CDR for a completed call are interpretted as follows: 1: CDR type,… |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.4 | TablerestDsmModExchTable | not-accessible | mandatory | This section of the MIB returns the exact exchange code used by the specified DSM for a given call number. It does not support getNext. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.4.1 | RowrestDsmModExchEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.4.1.1 | ColumnrestDsmModExchAddr | read-only | mandatory | Address of DSM module. Format is nest.slot. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.4.1.2 | ColumnrestDsmModExchCallNumLen | read-only | mandatory | This attribute defines the length of the restDsmModExchCallNumber attribute. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.4.1.3 | ColumnrestDsmModExchCallNumber | read-only | mandatory | The call number. The valid character set is defined in recfDsmDChExchTable MIB section. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.4.1.4 | ColumnrestDsmModExchPartition | read-only | mandatory | The partition id of the instance the user is inquiring information on. Partition 1 (global) should not match the instance partition id. It is able to obtain an… |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.4.1.5 | ColumnrestDsmModExchCode | read-only | mandatory | The call numbers matched exchange code. If there is no matched exchange code, an error message will be returned. The valid character set is defined in recfDsmD… |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.5 | TablerestDsmModRteTable | not-accessible | mandatory | This section of the MIB specifies all entries on both the local and remote routing tables. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.5.1 | RowrestDsmModRteEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.5.1.1 | ColumnrestDsmModRteAddr | read-only | mandatory | Address of DSM module. Format is nest.slot. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.5.1.2 | ColumnrestDsmModRteExchCodeLen | read-only | mandatory | This attribute defines the length of the restDsmModRteExchCode attribute. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.5.1.3 | ColumnrestDsmModRteExchCode | read-only | mandatory | The exchange code. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.5.1.4 | ColumnrestDsmModRtePartition | read-only | mandatory | Route partition ID. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.5.1.5 | ColumnrestDsmModRteRemoteNode | read-only | mandatory | Identifies the node containing the DSM that this routing entry refers to. For the local routing table entries, this attribute has a value of 0. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.5.1.6 | ColumnrestDsmModRteRemoteSlot | read-only | mandatory | Identifies the module address in the node defined in restDsmModRteRemoteNode that contains the DSM that this routing entry refers to. For the local routing tab… |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.5.1.7 | ColumnrestDsmModRteLocalPortNumber | read-only | mandatory | Identifies the physical D-channel port on the DSM that this routing entry refers to. For the remote routing table entries, this attribute has value of 0. |
| 1.3.6.1.4.1.16.101.1.2.2.4.10.5.1.8 | ColumnrestDsmModRteLocalPortAddress | read-only | mandatory | INTRODUCED 2.0.1 Identifies the virtual port address of the D-channel port that this routing entry refers to if the route is a local one. For remote routing ta… |
| 1.3.6.1.4.1.16.101.1.2.2.4.11 | NoderestLgmModule | |||
| 1.3.6.1.4.1.16.101.1.2.2.4.11.1 | TablerestLgmModuleTable | not-accessible | mandatory | This section of the MIB is used to get status of any LGM modules defined on the node. |
| 1.3.6.1.4.1.16.101.1.2.2.4.11.1.1 | RowrestLgmModuleEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.4.1.16.101.1.2.2.4.11.1.1.1 | ColumnrestLgmModuleAddr | read-only | mandatory | Address of this LGM module. Format is nest.slot. |
| 1.3.6.1.4.1.16.101.1.2.2.4.11.1.1.2 | ColumnrestLgmModuleTotalSAFs | read-only | mandatory | Maximum number of SAF allowed on this LGM module. |
| 1.3.6.1.4.1.16.101.1.2.2.4.11.1.1.3 | ColumnrestLgmModuleAvailSAFs | read-only | mandatory | Number of SAF that still can be allocated on this LGM module. Note that number of SAF allocated on this LGM module can be derived by subtraction of the value o… |
| 1.3.6.1.4.1.16.101.1.2.2.4.11.1.1.4 | ColumnrestLgmModuleTotalSCFs | read-only | mandatory | Maximum number of SCF allowed on this LGM module. |
| 1.3.6.1.4.1.16.101.1.2.2.4.11.1.1.5 | ColumnrestLgmModuleAvailSCFs | read-only | mandatory | Number of SCF that still can be allocated on this LGM module. Note that number of SCF allocated on this LGM module can be derived by subtraction of the value o… |
| 1.3.6.1.4.1.16.101.1.2.2.5 | TablerestPortTable | not-accessible | mandatory | This section of the MIB does not support getNext. |
| 1.3.6.1.4.1.16.101.1.2.2.5.1 | RowrestPortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.5.1.1 | ColumnrestPortAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.5.1.2 | ColumnrestPortDiagnostics | write-only | mandatory | Remove will free up the bus bandwidth used by the port. It will also set the port configuration start mode to off. This command will not work on server ports. … |
| 1.3.6.1.4.1.16.101.1.2.2.5.1.3 | ColumnrestPortStatus | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.5.1.4 | ColumnrestPortSubStatus | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.5.1.5 | ColumnrestPortCondition | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.5.1.6 | ColumnrestPortSubCondition | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.5.1.7 | ColumnrestPortType | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.5.1.8 | ColumnrestPortLoopbackType | write-only | mandatory | Indicates what type of loopback the user wishes to set on the port. lim specifies a local interface loopback. limDisc specifies a local interface loopback with… |
| 1.3.6.1.4.1.16.101.1.2.2.5.1.9 | ColumnrestPortLoopbackDuration | read-write | mandatory | Value 65535 specifies a permanent loopback. |
| 1.3.6.1.4.1.16.101.1.2.2.5.1.10 | ColumnrestPortLoopbackStatus | read-only | mandatory | If the port is in loopback, this field indicates the type of loopback. If the port is not in loopback, then none will be returned. |
| 1.3.6.1.4.1.16.101.1.2.2.5.1.11 | ColumnrestPortLoopbackInitiator | read-only | mandatory | If value is local, then loopback was initiated by user. If value is remote, then loopback was initiated by network. If no loopback is enabled, then this field … |
| 1.3.6.1.4.1.16.101.1.2.2.5.1.12 | ColumnrestPortErrorIndication | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.5.1.13 | ColumnrestPortSevereIndication | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.5.1.14 | ColumnrestPortBGDiagResults | read-only | mandatory | Results of port background diagnostics. Bit map is the same as for one port within recfSlotModulePortDiagMask. |
| 1.3.6.1.4.1.16.101.1.2.2.5.1.15 | ColumnrestPortNumberOfBundles | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.5.1.16 | ColumnrestPortPhasorStatus | read-only | mandatory | All bits zero indicates normal. bit 1 (lsb) indicates receive phasor underflow bit 2 indicates receive phasor overflow bit 3 indicates receive phasor empty bit… |
| 1.3.6.1.4.1.16.101.1.2.2.5.1.17 | ColumnrestPortMappedPhy | read-only | mandatory | For virtual port addresses, returns the physical port that this address is mapped to. If the virtual port address is not mapped to a physical port, then 0.0.0 … |
| 1.3.6.1.4.1.16.101.1.2.2.5.1.18 | ColumnrestPortSdmFunction | read-only | mandatory | Only applies to SDM ports (except SDM modules of hardware subtypes 33 (4 ports E1 balanced) and 34 (4 ports E1 unbalanced)). The bit map is: bit 1 (lsb) - DSR … |
| 1.3.6.1.4.1.16.101.1.2.2.5.1.19 | ColumnrestPortSdmTFunction | read-only | mandatory | Only applies to SDM ports. bit 1 (lsb) - TM if DTE, LL if DCE bit 2 - reserved if DTE, RL if DCE bit 3 - reserved bit 4 - reserved bit 5 - LL if DTE, TM if DCE… |
| 1.3.6.1.4.1.16.101.1.2.2.5.1.20 | ColumnrestPortBundleInTone | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.5.1.21 | ColumnrestPortSdmSignalStatus | read-only | mandatory | Only applies to SDM ports on modules of hardware subtypes 33 (4 ports E1 balanced) and 34 (4 ports E1 unbalanced). Otherwise it will return not applicable. |
| 1.3.6.1.4.1.16.101.1.2.2.5.1.22 | ColumnrestPortSdmBipolarViolationInd | read-only | mandatory | Only applies to SDM ports on modules of hardware subtypes 33 (4 ports E1 balanced) and 34 (4 ports E1 unbalanced). Otherwise it will return not applicable. |
| 1.3.6.1.4.1.16.101.1.2.2.5.1.23 | ColumnrestPortCapabilities | read-only | mandatory | If this attribute is not applicable, the return value consists of octet string of size 1 with the value none (255). Currently supported only by SDM port. The i… |
| 1.3.6.1.4.1.16.101.1.2.2.6 | TablerestBundleTable | not-accessible | mandatory | This section of the MIB does not support getNext. Creating (defining and then inserting) a new bundle out of available DS0s will not impact the existing bundle… |
| 1.3.6.1.4.1.16.101.1.2.2.6.1 | RowrestBundleEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.6.1.1 | ColumnrestBundleAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.6.1.2 | ColumnrestBundleDiagnostics | write-only | mandatory | Remove will free the bandwidth used by the bundle. If the bundle is an INL, then all channels connected over the INL will be disconnected. If the bundle is I/O… |
| 1.3.6.1.4.1.16.101.1.2.2.6.1.3 | ColumnrestBundleStatus | read-only | mandatory | The status is always enabled if the bundle is an INL. Unknown value means that the bundle is undefined. |
| 1.3.6.1.4.1.16.101.1.2.2.6.1.4 | ColumnrestBundleBwCntStatus | read-only | mandatory | Bandwidth contention status. |
| 1.3.6.1.4.1.16.101.1.2.2.6.1.5 | ColumnrestBundleMillwattSignalABCD | read-write | mandatory | Controls the tone generator for PCM channels. |
| 1.3.6.1.4.1.16.101.1.2.2.6.1.6 | ColumnrestBundleDS0Map | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.6.1.7 | ColumnrestBundleSignalA | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.6.1.8 | ColumnrestBundleSignalB | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.6.1.9 | ColumnrestBundleSignalC | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.6.1.10 | ColumnrestBundleSignalD | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.6.1.11 | ColumnrestBundleOutSigA | read-only | mandatory | This is not supported on T1M and E1M 4-port hardware configurationis |
| 1.3.6.1.4.1.16.101.1.2.2.6.1.12 | ColumnrestBundleOutSigB | read-only | mandatory | This is not supported on T1M and E1M 4-port hardware configurationis |
| 1.3.6.1.4.1.16.101.1.2.2.6.1.13 | ColumnrestBundleOutSigC | read-only | mandatory | This is not supported on T1M and E1M 4-port hardware configurationis |
| 1.3.6.1.4.1.16.101.1.2.2.6.1.14 | ColumnrestBundleOutSigD | read-only | mandatory | This is not supported on T1M and E1M 4-port hardware configurationis |
| 1.3.6.1.4.1.16.101.1.2.2.7 | TablerestINLTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.7.1 | RowrestINLEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.1 | ColumnrestINLNumber | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.2 | ColumnrestINLAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.3 | ColumnrestINLDiagnostics | write-only | mandatory | Remove will free bus bandwidth used by the INL, and disconnect all channels connected over the INL. It will also set the INL start mode in the configuration MI… |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.4 | ColumnrestINLStatus | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.5 | ColumnrestINLSubStatus | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.6 | ColumnrestINLLocalBERLevel | read-only | mandatory | BER level on the local node. If the local BER quality value is notCalculatedYet, then this attribute will return zero. |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.7 | ColumnrestINLLocalBERQuality | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.8 | ColumnrestINLRemoteNodeID | read-only | mandatory | Node number that the INL terminates on. If no remote connection has been established, then this attribute will return zero. |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.9 | ColumnrestINLRemotePortAddr | read-only | mandatory | Port or bundle address that the INL terminates on. If no remote connection has been established, then this attribute will return zero. |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.10 | ColumnrestINLRemoteINLID | read-only | mandatory | INL ID on the remote node that the INL terminates on. If no remote connection has been established, then this attribute will return zero. |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.11 | ColumnrestINLRemoteBERLevel | read-only | mandatory | BER level on the remote node that the INL terminates on. If the remote BER quality value is notCalculatedYet, then this attribute will return zero. |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.12 | ColumnrestINLRemoteBERQuality | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.13 | ColumnrestINLAvailableTDMBw | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.14 | ColumnrestINLAvailablePacketBw | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.15 | ColumnrestINLLoopbackDuration | read-write | mandatory | Value 65535 specifies a permanent loopback. |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.16 | ColumnrestINLLoopbackStatus | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.17 | ColumnrestINLTotalCRCErrors | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.18 | ColumnrestINLBERWindowFill | read-only | mandatory | Format e.g. 10/32, 5/32. |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.19 | ColumnrestINLNumTdmCh | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.20 | ColumnrestINLNumFrCh | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.21 | ColumnrestINLSpeed | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.22 | ColumnrestINLNumSaf | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.23 | ColumnrestINLLOSMode | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.7.1.24 | ColumnrestINLBusFrameMode | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.8 | TablerestINLContentsTable | not-accessible | mandatory | This table lists all of the channels on a specified INL. |
| 1.3.6.1.4.1.16.101.1.2.2.8.1 | RowrestINLContentsEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.8.1.1 | ColumnrestINLContentsINLNumber | read-only | mandatory | INL 32 is used to display local connections. |
| 1.3.6.1.4.1.16.101.1.2.2.8.1.2 | ColumnrestINLContentsSeqNumber | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.8.1.3 | ColumnrestINLContentsSourceNodeID | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.8.1.4 | ColumnrestINLContentsSourceAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.8.1.5 | ColumnrestINLContentsDestNodeID | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.8.1.6 | ColumnrestINLContentsDestAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.9 | NoderestChannel | |||
| 1.3.6.1.4.1.16.101.1.2.2.9.1 | TablerestChannelTable | not-accessible | mandatory | This section of the MIB is defined for all types of channels. This section of the MIB will only support getNext for local channel addresses. |
| 1.3.6.1.4.1.16.101.1.2.2.9.1.1 | RowrestChannelEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.9.1.1.1 | ColumnrestChannelStatusAddr | read-only | mandatory | One of two channel address types: (1) Local channel address, where the channel originates and/or terminates on this node. The address specifies a channel endpo… |
| 1.3.6.1.4.1.16.101.1.2.2.9.1.1.2 | ColumnrestChannelSourceNodeID | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.9.1.1.3 | ColumnrestChannelSourceAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.9.1.1.4 | ColumnrestChannelDestNodeID | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.9.1.1.5 | ColumnrestChannelDestAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.9.1.1.6 | ColumnrestChannelDiagnostics | write-only | mandatory | Reset will disconnect and then reconnect the specified channel. Set and clear loopback are the only controls that will accept a remote channel address (i.e., o… |
| 1.3.6.1.4.1.16.101.1.2.2.9.1.1.7 | ColumnrestChannelDirectNodeConnect | write-only | mandatory | Connect the channel by selecting a route that passes through these specific nodes. Up to 17 node numbers can be specified. Each node number requires two bytes.… |
| 1.3.6.1.4.1.16.101.1.2.2.9.1.1.8 | ColumnrestChannelDirectPathConnect | write-only | mandatory | Connect the channel using the specified route. For TDM and subrate channels, each hop of the path is indicates using three bytes. The first two bytes are the n… |
| 1.3.6.1.4.1.16.101.1.2.2.9.1.1.9 | ColumnrestChannelStatus | read-only | mandatory | If the channel is disconnected, see recfTDMChannelDisconnect (for TDM and subrate channels) or recfFrChannelDisconnect (for packet channels) for the reason. If… |
| 1.3.6.1.4.1.16.101.1.2.2.9.1.1.10 | ColumnrestChannelSubStatus | read-only | mandatory | The waitForRTSAck value is only valid when the channel status is connecting. None value is valid for all channel status. The other values are only valid when t… |
| 1.3.6.1.4.1.16.101.1.2.2.9.1.1.11 | ColumnrestChannelType | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.9.1.1.12 | ColumnrestChannelBandwidth | read-only | mandatory | Returns the badwidth value this channel occupies on the bus of an INL. |
| 1.3.6.1.4.1.16.101.1.2.2.9.1.1.13 | ColumnrestChannelBypassCount | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.9.1.1.14 | ColumnrestChannelPath | read-only | deprecated | DEPRECATED 2.0.1 For TDM and subrate channels, each hop of the path is indicates using three bytes. The first two bytes are the node number. The most significa… |
| 1.3.6.1.4.1.16.101.1.2.2.9.1.1.15 | ColumnrestChannelRouteQuality | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.9.1.1.16 | ColumnrestChannelConnectTime | read-only | mandatory | Value is number of seconds since midnight January 1, 1970, GMT. |
| 1.3.6.1.4.1.16.101.1.2.2.9.1.1.17 | ColumnrestChannelRetryCounter | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.9.1.1.18 | ColumnrestChannelLoopbackNode | read-only | mandatory | If a channel is in loopback, this field indicates which node the channel loopback has been set on. |
| 1.3.6.1.4.1.16.101.1.2.2.9.1.1.19 | ColumnrestChannelNodalSubratePath | read-only | mandatory | Lists the path of a subrate channel within the node. The format for each segment is as follows: bytes 1-2: Node number if this is a remote address. If local ad… |
| 1.3.6.1.4.1.16.101.1.2.2.9.1.1.20 | ColumnrestChannelDChOrigNode | read-only | mandatory | INTRODUCED 2.0.0 This attribute indicates the node where the originating D-channel port is allocated. If a channel does not have any associated D-channels, the… |
| 1.3.6.1.4.1.16.101.1.2.2.9.1.1.21 | ColumnrestChannelDChOrigAddr | read-only | mandatory | INTRODUCED 2.0.0 This attribute indicates the originating D-channel port address. If a channel does not have any associated D-channels, then zero shall be retu… |
| 1.3.6.1.4.1.16.101.1.2.2.9.1.1.22 | ColumnrestChannelDChTermNode | read-only | mandatory | INTRODUCED 2.0.0 This attribute indicates the node where the terminating D-channel port is allocated. If a channel does not have any associated D-channels, the… |
| 1.3.6.1.4.1.16.101.1.2.2.9.1.1.23 | ColumnrestChannelDChTermAddr | read-only | mandatory | INTRODUCED 2.0.0 This attribute indicates the terminating D-channel port address. If a channel does not have any associated D-channels, then zero shall be retu… |
| 1.3.6.1.4.1.16.101.1.2.2.9.1.1.24 | ColumnrestChannelLoopbackModAddr | read-write | mandatory | INTRODUCED 2.0.0 This attribute is a supplement to the restChannelDiagnostics attribute. It specifies the address of the module that implements this loopback. … |
| 1.3.6.1.4.1.16.101.1.2.2.9.1.1.25 | ColumnrestChannelNetworkPath | read-only | mandatory | INTRODUCED 2.0.1 This attribute represents all of the hops of a channel's route within an ST network or an ST-LINK hybrid network. The data for each hop consis… |
| 1.3.6.1.4.1.16.101.1.2.2.9.2 | TablerestPktChannelTable | not-accessible | mandatory | This section of the MIB is only defined for frame relay channels. |
| 1.3.6.1.4.1.16.101.1.2.2.9.2.1 | RowrestPktChannelEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.9.2.1.1 | ColumnrestPktChannelAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.9.2.1.2 | ColumnrestPktChannelDiagnostics | write-only | mandatory | For enable packet test generator commands (local and remote), the channel should be put into loopback first using the setLoopback command in restChannelDiagnos… |
| 1.3.6.1.4.1.16.101.1.2.2.9.2.1.3 | ColumnrestPktChannelTestGenStatus | read-only | mandatory | Specifies whether a test generator is currently active on this channel, and if so, whether it is local or remote. |
| 1.3.6.1.4.1.16.101.1.2.2.9.2.1.4 | ColumnrestPktChannelTestGenFrSent | read-only | mandatory | Number of test generator frames sent. |
| 1.3.6.1.4.1.16.101.1.2.2.9.2.1.5 | ColumnrestPktChannelTestGenFrRcvOK | read-only | mandatory | Number of test generator frames received without any errors. |
| 1.3.6.1.4.1.16.101.1.2.2.9.2.1.6 | ColumnrestPktChannelTestGenFrRcvErr | read-only | mandatory | Number of test generator frames received with at least one error. |
| 1.3.6.1.4.1.16.101.1.2.2.9.2.1.7 | ColumnrestPktChannelTestGenFrTimeOut | read-only | mandatory | Number of test generator frames sent that were not received. |
| 1.3.6.1.4.1.16.101.1.2.2.9.2.1.8 | ColumnrestPktChannelPingStatus | read-only | mandatory | Specifies whether the channel is sending ping messages or not. |
| 1.3.6.1.4.1.16.101.1.2.2.9.2.1.9 | ColumnrestPktChannelPingNumTimes | write-only | mandatory | Sets the number of times that the ping message should be sent on the frame relay channel, and enables the ping. The packet ping command is used to collect dela… |
| 1.3.6.1.4.1.16.101.1.2.2.9.2.1.10 | ColumnrestPktChannelPingNumRemaining | read-only | mandatory | Number of times that the ping message the ping message still has to be sent, when ping is active. If ping is inactive, or if the user requested the ping to con… |
| 1.3.6.1.4.1.16.101.1.2.2.9.2.1.11 | ColumnrestPktChannelCommStatus | read-only | mandatory | INTRODUCED 2.0.0 This attribute indicates the status of the communication via this packet channel. It will return notApplicable for frame relay channels on FSM… |
| 1.3.6.1.4.1.16.101.1.2.2.9.3 | TablerestPktChPingTable | not-accessible | mandatory | This section of the MIB is only defined for frame relay channels. |
| 1.3.6.1.4.1.16.101.1.2.2.9.3.1 | RowrestPktChPingEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.9.3.1.1 | ColumnrestPktChPingAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.9.3.1.2 | ColumnrestPktChPingHopNumber | read-only | mandatory | Identifies what hop of the channel path this information applies to. The first hop originates from the node that the ping was initiated on (this node will be r… |
| 1.3.6.1.4.1.16.101.1.2.2.9.3.1.3 | ColumnrestPktChPingDelay | read-only | mandatory | Indicates the round trip delay in units of 10 millseconds between this node and the terminating node is. |
| 1.3.6.1.4.1.16.101.1.2.2.9.3.1.4 | ColumnrestPktChPingOrigTermCong | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.9.3.1.5 | ColumnrestPktChPingTermOrigCong | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10 | NoderestAd10Port | |||
| 1.3.6.1.4.1.16.101.1.2.2.10.1 | TablerestAd10AgmPortTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10.1.1 | RowrestAd10AgmPortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10.1.1.1 | ColumnrestAd10AgmPortAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10.1.1.2 | ColumnrestAd10AgmPortControl | write-only | mandatory | tdmMuxSwitch will force AD-10 port configured speeds to match ST values. It will then initiate a TDM mux switch on the AD-10. unitReset will reset the AD-10 un… |
| 1.3.6.1.4.1.16.101.1.2.2.10.1.1.3 | ColumnrestAd10AgmPortCpSpeed | read-only | mandatory | Console terminal baud rate |
| 1.3.6.1.4.1.16.101.1.2.2.10.1.1.4 | ColumnrestAd10AgmPortCpTermType | read-only | mandatory | Console terminal type |
| 1.3.6.1.4.1.16.101.1.2.2.10.1.1.5 | ColumnrestAd10AgmPortCpMode | read-write | mandatory | Console pass through mode |
| 1.3.6.1.4.1.16.101.1.2.2.10.1.1.6 | ColumnrestAd10Date | read-write | mandatory | Format is mm/dd/yyyy |
| 1.3.6.1.4.1.16.101.1.2.2.10.1.1.7 | ColumnrestAd10Time | read-write | mandatory | Format is hh:mm:ss |
| 1.3.6.1.4.1.16.101.1.2.2.10.1.1.8 | ColumnrestAd10VersionLabel | read-only | mandatory | Format: Vxx.yy DATE:mm-dd-yy The date is a date stamp on the version number. |
| 1.3.6.1.4.1.16.101.1.2.2.10.1.1.9 | ColumnrestAd10UnitSerialNumberStr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10.1.1.10 | ColumnrestAd10UnitType | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10.1.1.11 | ColumnrestAd10HWConfig | read-only | mandatory | Ad10 hardware configuration map. For each port on the Ad10 , there is a one-byte port type field followed by a five-byte user port address. The port type field… |
| 1.3.6.1.4.1.16.101.1.2.2.10.1.1.12 | ColumnrestAd10NetworkInterface | read-only | mandatory | Ad10 network port interface type |
| 1.3.6.1.4.1.16.101.1.2.2.10.1.1.13 | ColumnrestAd10NetworkClockConf | read-only | mandatory | Ad10 network port clock configuration |
| 1.3.6.1.4.1.16.101.1.2.2.10.1.1.14 | ColumnrestAd10TdmMuxSwitchStatus | read-only | mandatory | Status of the tdmMuxSwitch command. |
| 1.3.6.1.4.1.16.101.1.2.2.10.1.1.15 | ColumnrestAd10SoftloadStatus | read-only | mandatory | AD10 current softload status. |
| 1.3.6.1.4.1.16.101.1.2.2.10.1.1.16 | ColumnrestAd10SoftloadFileSize | read-only | mandatory | Total number of bytes to be softloaded. If no softloading is in progress returns zero. |
| 1.3.6.1.4.1.16.101.1.2.2.10.1.1.17 | ColumnrestAd10SoftloadTransferred | read-only | mandatory | Number of bytes that have been transferred currently. If no softloading is in progress returns zero. |
| 1.3.6.1.4.1.16.101.1.2.2.10.1.1.18 | ColumnrestAd10SoftloadStartTime | read-only | mandatory | Value is number of seconds since midnight January 1, 1970, GMT. Value of 0 means not applicable. |
| 1.3.6.1.4.1.16.101.1.2.2.10.1.1.19 | ColumnrestAd10SoftloadCompletionTime | read-only | mandatory | Value is number of seconds since midnight January 1, 1970, GMT. Value of 0 means not applicable. |
| 1.3.6.1.4.1.16.101.1.2.2.10.2 | TablerestAd10DataPortTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1 | RowrestAd10DataPortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.1 | ColumnrestAd10DataPortAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.2 | ColumnrestAd10DataPortDiagnostics | write-only | mandatory | Insert will download the new MIB to the module. It will not synchronize any configuration parameters between the AD-10 and the NCP. Remove will disconnect the … |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.3 | ColumnrestAd10DataPortMode | read-write | mandatory | Online/offline and diagnostic mode |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.4 | ColumnrestAd10DataPortIntfType | read-only | mandatory | Interface type |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.5 | ColumnrestAd10DataPortClockMode | read-write | mandatory | Clock mode. Only TDM sync can use a value of derived. If port is async, notApplicable will be returned. The notApplicable value should not be set. |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.6 | ColumnrestAd10DataPortClockRate | read-write | mandatory | Clock rate, in units of 100 bps. |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.7 | ColumnrestAd10DataPortCtsOOS | read-write | mandatory | CTS out of service |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.8 | ColumnrestAd10DataPortCtsSig | read-write | mandatory | CTS setup |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.9 | ColumnrestAd10DataPortDcdOOS | read-write | mandatory | DCD out of service |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.10 | ColumnrestAd10DataPortDcdSig | read-write | mandatory | DCD setup |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.11 | ColumnrestAd10DataPortDsrOOS | read-write | mandatory | DSR out of service |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.12 | ColumnrestAd10DataPortDsrSig | read-write | mandatory | DSR setup |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.13 | ColumnrestAd10DataPortRtsLoopDelay | read-write | mandatory | RTS loopback delay number in units of milli-seconds |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.14 | ColumnrestAd10DataPortDtrLoopDelay | read-write | mandatory | DTR loopback delay number in units of milli-seconds |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.15 | ColumnrestAd10DataPortAsyncDataBits | read-write | mandatory | Asynchronous data bits configuration |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.16 | ColumnrestAd10DataPortAsyncStopBits | read-write | mandatory | Asynchronous stop bits configuration |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.17 | ColumnrestAd10DataPortAsyncParity | read-write | mandatory | Asynchronous parity configuration |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.18 | ColumnrestAd10DataPortAsyncSubMode | read-write | mandatory | Asynchronous parity error substitute mode |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.19 | ColumnrestAd10DataPortAsyncSubChar | read-write | mandatory | Asynchronous parity error substitute character |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.20 | ColumnrestAd10DataPortPktFlowControl | read-write | mandatory | Flow control mechanism (for async only) |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.21 | ColumnrestAd10DataPortPktTxFlow | read-write | mandatory | Transmit flow |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.22 | ColumnrestAd10DataPortPktRxFlow | read-write | mandatory | Receive flow |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.23 | ColumnrestAd10DataPortPktBuildTimeOut | read-write | mandatory | Build packet time out (in units of 10 milliseconds) (for async only) |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.24 | ColumnrestAd10DataPortPktRxThreshold | read-write | mandatory | Receive threshold. Receive buffer capacity beyond the threshold, the flow control signal will send toward the network. |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.25 | ColumnrestAd10DataPortPktTxThreshold | read-write | mandatory | Transmit threshold. Transmit buffer capacity beyond the threshold, the flow control signal will send toward the network. |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.26 | ColumnrestAd10DataPortPktMinRxFrag | read-write | mandatory | Minimum receive fragment threshold. Specifies the minimum number received fragments of packet from the network before sending toward DTE. |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.27 | ColumnrestAd10DataPortBiSyncCharType | read-write | mandatory | Bisync character type |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.28 | ColumnrestAd10DataPortBiSyncParity | read-write | mandatory | Bisync parity |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.29 | ColumnrestAd10DataPortBiSyncIdleFill | read-write | mandatory | Bisync idle fill |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.30 | ColumnrestAd10DataPortBiSyncMinPair | read-write | mandatory | Bisync minimum sync pair. Minimum number of sync character pair that precedes a packet. |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.31 | ColumnrestAd10DataPortBiSyncSyncChar | read-write | mandatory | Bisync sync character. Default is 32h for EBCDIC and 16h for ASCII 7 and 8. |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.32 | ColumnrestAd10DataPortBiSyncPadChar | read-write | mandatory | Bisync pad character. Default is 0xff for EBCDIC and ASCII 8 and 0x7f for ASCII 7. |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.33 | ColumnrestAd10DataPortHdlcCrcType | read-write | mandatory | CRC type |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.34 | ColumnrestAd10DataPortHdlcLineCode | read-write | mandatory | Line code |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.35 | ColumnrestAd10DataPortHdlcIdleFill | read-write | mandatory | Idle fill |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.36 | ColumnrestAd10DataPortHdlcMinFlags | read-write | mandatory | Minimum flags between frames |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.37 | ColumnrestAd10DataPortModemSigInfo | read-only | mandatory | Modem signal info. Bit map. bit 1 (lsb) - RTS bit 2 - DTR bit 3 - CTS bit 4 - DCD bit 5 - DSR |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.38 | ColumnrestAd10DataPortVcMapDlci | read-write | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.39 | ColumnrestAd10DataPortVcMapCir | read-write | mandatory | Committed information rate (in units of 100 bps) |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.40 | ColumnrestAd10DataPortTDMDataRate | read-only | mandatory | This attribute must match the value in recfAd10DataPortTDMDataRate. If it does not match, the reset AD-10 data port command can be used to synchronize them. |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.41 | ColumnrestAd10DataPortType | read-only | mandatory | This attribute must match the value in recfAd10DataPortType. If it does not match, the reset AD-10 data port command can be used to synchronize them. |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.42 | ColumnrestAd10DataPortDtrFlLpDlyDelta | read-write | mandatory | INTRODUCED 1.2.3 Dtr falling edge (going from high to low) delay is this attribute + restAd10DataPortDtrLoopDelay |
| 1.3.6.1.4.1.16.101.1.2.2.10.2.1.43 | ColumnrestAd10DataPortRtsFlLpDlyDelta | read-write | mandatory | INTRODUCED 1.2.3 Rts falling edge (going from high to low) delay is this attribute + restAd10DataPortRtsLoopDelay |
| 1.3.6.1.4.1.16.101.1.2.2.10.3 | TablerestAd10VoicePortTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10.3.1 | RowrestAd10VoicePortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10.3.1.1 | ColumnrestAd10VoicePortAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10.3.1.2 | ColumnrestAd10VoicePortDiagnostics | write-only | mandatory | Insert will download the new MIB to the module. It will not synchronize any configuration parameters between the AD-10 and the NCP. Remove will disconnect the … |
| 1.3.6.1.4.1.16.101.1.2.2.10.3.1.3 | ColumnrestAd10VoicePortMode | read-write | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10.3.1.4 | ColumnrestAd10VoicePortInterface | read-write | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10.3.1.5 | ColumnrestAd10VoicePortEchoCancel | read-write | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10.3.1.6 | ColumnrestAd10VoicePortToneMode | read-write | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10.3.1.7 | ColumnrestAd10VoicePortNonLinear | read-write | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10.3.1.8 | ColumnrestAd10VoicePortEMPolarity | read-write | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10.3.1.9 | ColumnrestAd10VoicePortUncfgCktSig | read-write | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10.3.1.10 | ColumnrestAd10VoicePortHookStateRx | read-only | mandatory | Phone on/off hook status |
| 1.3.6.1.4.1.16.101.1.2.2.10.3.1.11 | ColumnrestAd10VoicePortHookStateTx | read-only | mandatory | Phone on/off hook status |
| 1.3.6.1.4.1.16.101.1.2.2.10.3.1.12 | ColumnrestAd10VoicePortTxLevel | read-write | mandatory | -25.4db to +25.4db w/.2db increment |
| 1.3.6.1.4.1.16.101.1.2.2.10.3.1.13 | ColumnrestAd10VoicePortRcvLevel | read-write | mandatory | -25.4db to +25.4db w/.2db increment |
| 1.3.6.1.4.1.16.101.1.2.2.10.3.1.14 | ColumnrestAd10VoicePortTermination | read-write | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10.3.1.15 | ColumnrestAd10VoicePortWire | read-write | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10.3.1.16 | ColumnrestAd10VoicePortAc15Dial | read-write | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10.3.1.17 | ColumnrestAd10VoicePortTelcoIntType | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10.3.1.18 | ColumnrestAd10VoicePortSpeed | read-only | mandatory | The compressed channel data rate for this AD-10 voice port. This attribute must match the value in recfAd10VoicePortSpeed. If it does not match, the reset AD-1… |
| 1.3.6.1.4.1.16.101.1.2.2.10.3.1.19 | ColumnrestAd10VoicePortCompressMode | read-only | mandatory | This attribute must match the value in recfAd10VoicePortCompressMode. If it does not match, the reset AD-10 voice port command can be used to synchronize them. |
| 1.3.6.1.4.1.16.101.1.2.2.10.3.1.20 | ColumnrestAd10VoicePortFaxMode | read-only | mandatory | This attribute must match the value in recfAd10VoicePortFaxMode. If it does not match, the reset AD-10 voice port command can be used to synchronize them. |
| 1.3.6.1.4.1.16.101.1.2.2.10.3.1.21 | ColumnrestAd10VoicePortOOSAudio | read-write | mandatory | INTRODUCED 1.2.3 OOS audio signal for AD-10 voice ports. |
| 1.3.6.1.4.1.16.101.1.2.2.10.3.1.22 | ColumnrestAd10VoicePortCelpNetSigMd | read-write | mandatory | INTRODUCED 2.0.0 Enable autodetection of CELP/ATC channel connected equipment so as to automatically change format to become compatible with either LINK (5 byt… |
| 1.3.6.1.4.1.16.101.1.2.2.10.3.1.23 | ColumnrestAd10VoicePortCelpNetSigSt | read-only | mandatory | INTRODUCED 2.0.0 When restAd10VoiceTrkGrpCelpNetSigMd attribute is set to auto (autodetection mode), this parameter indicates whether the CELP/ATC channel conn… |
| 1.3.6.1.4.1.16.101.1.2.2.10.4 | TablerestAd10PktBandTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10.4.1 | RowrestAd10PktBandEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10.4.1.1 | ColumnrestAd10PktBandAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.10.4.1.2 | ColumnrestAd10PktBandDiagnostics | write-only | mandatory | Insert will download the new MIB to the module. It will not synchronize any configuration parameters between the AD-10 and the NCP. Remove will disconnect the … |
| 1.3.6.1.4.1.16.101.1.2.2.10.4.1.3 | ColumnrestAd10PktBandStatMuxMode | read-write | deprecated | DEPRECATED 2.0 Online/offline and diagnosis mode. |
| 1.3.6.1.4.1.16.101.1.2.2.10.4.1.4 | ColumnrestAd10PktBandMaxSegSize | read-write | mandatory | Maximum frame size |
| 1.3.6.1.4.1.16.101.1.2.2.10.4.1.5 | ColumnrestAd10PktBandBaudRate | read-only | mandatory | This attribute must match the value in recfAd10PktBandBaudRate. If it does not match, the reset AD-10 packet band command can be used to synchronize them. If r… |
| 1.3.6.1.4.1.16.101.1.2.2.10.4.1.6 | ColumnrestAd10PktBandMinBandwidth | read-only | mandatory | Returns the value of the packet band port bandwidth with all configured DBA voice ports off-hook. The units of this value are 400/3 Hz. |
| 1.3.6.1.4.1.16.101.1.2.2.10.4.1.7 | ColumnrestAd10PktBandCurBandwidth | read-only | mandatory | Returns the current value of the packet band port bandwidth. The units of this value are 400/3 Hz. |
| 1.3.6.1.4.1.16.101.1.2.2.10.4.1.8 | ColumnrestAd10PktBandMaxBandwidth | read-only | mandatory | Returns the value of the packet band port bandwidth with all configured DBA voice ports on-hook. The units of this value are 400/3 Hz. |
| 1.3.6.1.4.1.16.101.1.2.2.11 | NoderestAsmPort | |||
| 1.3.6.1.4.1.16.101.1.2.2.11.1 | NoderestAsmX50Table | |||
| 1.3.6.1.4.1.16.101.1.2.2.11.1.1 | TablerestAsmX50PortTable | not-accessible | mandatory | This section of the MIB does not support getNext. |
| 1.3.6.1.4.1.16.101.1.2.2.11.1.1.1 | RowrestAsmX50PortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.11.1.1.1.1 | ColumnrestAsmX50PortAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.11.1.1.1.2 | ColumnrestAsmX50PortEngine | read-only | mandatory | Indicates which DSP on the ASM module the port has been allocated to. |
| 1.3.6.1.4.1.16.101.1.2.2.11.1.1.1.3 | ColumnrestAsmX50PortRxHouseKbits | read-only | mandatory | bit housekeeping bit 0 (lsb) 'H' 1 'G' 2 'F' 3 'E' 4 'D' 5 'C' 6 'B' 7 not used |
| 1.3.6.1.4.1.16.101.1.2.2.11.1.1.1.4 | ColumnrestAsmX50PortCktTimeSlotMap | read-only | mandatory | Each byte 1-20 indicates which circuit is using that time slot. |
| 1.3.6.1.4.1.16.101.1.2.2.11.1.1.1.5 | ColumnrestAsmX50PortAggrStatus | read-only | mandatory | Specific ASM X50 status. |
| 1.3.6.1.4.1.16.101.1.2.2.11.1.2 | TablerestAsmX50CkTable | not-accessible | mandatory | This section of the MIB does not support getNext. |
| 1.3.6.1.4.1.16.101.1.2.2.11.1.2.1 | RowrestAsmX50CkEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.11.1.2.1.1 | ColumnrestAsmX50CkAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.11.1.2.1.2 | ColumnrestAsmX50CkDiagnostics | write-only | mandatory | Insert will download the new MIB to the module and set the start mode in the configuration MIB to automatic. Remove will disconnect the connected channel and c… |
| 1.3.6.1.4.1.16.101.1.2.2.11.1.2.1.3 | ColumnrestAsmX50CkSbitStatus | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.11.1.2.1.4 | ColumnrestAsmX50CkPhasorStatus | read-only | mandatory | All bits zero indicates normal. bit 1 (lsb) indicates receive phasor underflow bit 2 indicates receive phasor overflow bit 3 indicates receive phasor empty bit… |
| 1.3.6.1.4.1.16.101.1.2.2.11.2 | NoderestAsmVoice | |||
| 1.3.6.1.4.1.16.101.1.2.2.11.2.1 | TablerestAsmVoicePortTable | not-accessible | mandatory | This section of the MIB doesn't support getNext. |
| 1.3.6.1.4.1.16.101.1.2.2.11.2.1.1 | RowrestAsmVoicePortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.11.2.1.1.1 | ColumnrestAsmVoicePortChannelAddr | read-only | mandatory | Address of T1M/E1M bundle which is being used by this port while connected. If disconnected returns error |
| 1.3.6.1.4.1.16.101.1.2.2.11.2.1.1.2 | ColumnrestAsmVoicePortAddr | read-only | mandatory | ASM voice port physical address in nest:slot:port format |
| 1.3.6.1.4.1.16.101.1.2.2.11.2.1.1.3 | ColumnrestAsmVoicePortTrkGrpAddr | read-only | mandatory | Trunk group address this ASM voice port is assigned to |
| 1.3.6.1.4.1.16.101.1.2.2.11.2.1.1.4 | ColumnrestAsmVoicePortEngine | read-only | mandatory | The ASM module DSP number allocated for this voice port |
| 1.3.6.1.4.1.16.101.1.2.2.11.2.1.1.5 | ColumnrestAsmVoicePortPacketSize | read-only | mandatory | Size of compressed data block. This field is not supported in this release. |
| 1.3.6.1.4.1.16.101.1.2.2.11.2.1.1.6 | ColumnrestAsmVoicePortBlockSize | read-only | mandatory | Size of uncompressed data block. This field is not supported in this release. |
| 1.3.6.1.4.1.16.101.1.2.2.11.2.1.1.7 | ColumnrestAsmVoicePortEchoCanceller | read-only | mandatory | The bit mask is: bit 0(lsb)divergence (0-normal, 1-diverge) bit 1 reserved bit 2 filter (0-disabled, 1-enabled) bit 3 adaptation (0-frosen, 1-adapting) bit 4 r… |
| 1.3.6.1.4.1.16.101.1.2.2.11.2.1.1.8 | ColumnrestAsmVoicePortDTMFRelay | read-only | mandatory | The bit mask is: bits 0(lsb)-3 detected character 0 - 9 digit 0 through 9 10 character '*' 11 character '#' 12-15 characters 'A' through 'D' bits 4,5 digit typ… |
| 1.3.6.1.4.1.16.101.1.2.2.11.2.1.1.9 | ColumnrestAsmVoicePortFaxRelay | read-only | mandatory | The bit mask is: bits 0(lsb)-4 modulation type 0 V.21 300 bps 1 V.27 2400 bps 2 V.27 4800 bps 3 V.29 7200 bps 4 V.29 9600 bps bit 5 reserved bit 6 demodulation… |
| 1.3.6.1.4.1.16.101.1.2.2.11.2.1.1.10 | ColumnrestAsmVoicePortPacket | read-only | mandatory | The bit mask is: bit 0(lsb)sync init (1-initializing) bit 1 sync acq (1-sync searching) bit 2 sync ver (1-verifying sync) bit 3 sync mon (1-normal) bit 4 sync … |
| 1.3.6.1.4.1.16.101.1.2.2.11.2.1.1.11 | ColumnrestAsmVoicePortSubratePhasor | read-only | mandatory | All bits zero indicates normal. bit 1(lsb)receive phasor underflow bit 2 receive phasor overflow bit 3-8 are reserved bit 9 transmit phasor underflow bit 10 tr… |
| 1.3.6.1.4.1.16.101.1.2.2.11.2.1.1.12 | ColumnrestAsmVoicePortSignalingLOS | read-only | mandatory | Signaling LOS status. |
| 1.3.6.1.4.1.16.101.1.2.2.11.2.1.1.13 | ColumnrestAsmVoicePortFrameLOS | read-only | mandatory | Frame LOS status. |
| 1.3.6.1.4.1.16.101.1.2.2.11.2.1.1.14 | ColumnrestAsmVoicePortCelpNetSigSt | read-only | mandatory | INTRODUCED 2.0.0 When recfAsmVoiceTrkGrpCelpNetSigMd attribute is set to auto (autodetection mode), this parameter indicates whether the CELP/ATC channel conne… |
| 1.3.6.1.4.1.16.101.1.2.2.12 | NoderestTrunkGroup | |||
| 1.3.6.1.4.1.16.101.1.2.2.12.1 | TablerestTrkGrpTable | not-accessible | mandatory | This section of the MIB is intended to use for any trunk groups status defined. It doesn't support getNext. This section is not supported in this release. |
| 1.3.6.1.4.1.16.101.1.2.2.12.1.1 | RowrestTrkGrpEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.12.1.1.1 | ColumnrestTrkGrpAddr | read-only | mandatory | Address of the trunk group |
| 1.3.6.1.4.1.16.101.1.2.2.12.1.1.2 | ColumnrestTrkGrpStatus | read-only | mandatory | The current trunk group status |
| 1.3.6.1.4.1.16.101.1.2.2.12.2 | TablerestTrkGrpContentsTable | not-accessible | mandatory | This section of the MIB specify all the contents of the trunk groups status defined. It partially supports getNext (only within trunk group). This section is n… |
| 1.3.6.1.4.1.16.101.1.2.2.12.2.1 | RowrestTrkGrpContentsEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.12.2.1.1 | ColumnrestTrkGrpContentsAddr | read-only | mandatory | Address of the trunk group |
| 1.3.6.1.4.1.16.101.1.2.2.12.2.1.2 | ColumnrestTrkGrpContentsSequenceID | read-only | mandatory | Used to index multiple ports assigned to this trunk group |
| 1.3.6.1.4.1.16.101.1.2.2.12.2.1.3 | ColumnrestTrkGrpContentsSrcNodeID | read-only | mandatory | Source node ID of the current channel |
| 1.3.6.1.4.1.16.101.1.2.2.12.2.1.4 | ColumnrestTrkGrpContentsSrcTrkGrpAddr | read-only | mandatory | Source truk group address of the current channel |
| 1.3.6.1.4.1.16.101.1.2.2.12.2.1.5 | ColumnrestTrkGrpContentsSrcChAddr | read-only | mandatory | Source end point address of the current channel (T1M/E1M port) using this trunk group. When disconnected returns an error |
| 1.3.6.1.4.1.16.101.1.2.2.12.2.1.6 | ColumnrestTrkGrpContentsDstNodeID | read-only | mandatory | Destination node ID of the current channel |
| 1.3.6.1.4.1.16.101.1.2.2.12.2.1.7 | ColumnrestTrkGrpContentsDstTrkGrpAddr | read-only | mandatory | Destination truk group address of the current channel |
| 1.3.6.1.4.1.16.101.1.2.2.12.2.1.8 | ColumnrestTrkGrpContentsDstChAddr | read-only | mandatory | Destination end point address of the current channel (T1M/E1M port) using this trunk group. When disconnected returns an error |
| 1.3.6.1.4.1.16.101.1.2.2.13 | NoderestRtmPort | |||
| 1.3.6.1.4.1.16.101.1.2.2.13.1 | TablerestRtmPortTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.13.1.1 | RowrestRtmPortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.13.1.1.1 | ColumnrestRtmPortAddr | read-only | mandatory | RTM port physical address in nest:slot:port format |
| 1.3.6.1.4.1.16.101.1.2.2.13.1.1.2 | ColumnrestRtmPortAdFmtRevision | read-only | mandatory | Format revision of the ADx. |
| 1.3.6.1.4.1.16.101.1.2.2.13.1.1.3 | ColumnrestRtmPortAdType | read-only | mandatory | Type of the Adx unit. |
| 1.3.6.1.4.1.16.101.1.2.2.13.1.1.4 | ColumnrestRtmPortAdSubtype | read-only | mandatory | In case of integralInt all interfaces are V24 (AD-3I/AD-7I subtype). In case of daughterBrdInt the interface type is determined by reading restRtmAdPortElIntSt… |
| 1.3.6.1.4.1.16.101.1.2.2.13.1.1.5 | ColumnrestRtmPortAdAssemblyNmb | read-only | mandatory | ADx unit assembly number. |
| 1.3.6.1.4.1.16.101.1.2.2.13.1.1.6 | ColumnrestRtmPortAdMotherBrdAssmNmb | read-only | mandatory | Motherboard assembly number. |
| 1.3.6.1.4.1.16.101.1.2.2.13.1.1.7 | ColumnrestRtmPortAdSerialNmb | read-only | mandatory | ADx unit serial number. |
| 1.3.6.1.4.1.16.101.1.2.2.13.1.1.8 | ColumnrestRtmPortAdManufactDate | read-only | mandatory | ADx unit manufacturing date. |
| 1.3.6.1.4.1.16.101.1.2.2.13.1.1.9 | ColumnrestRtmPortAdRamSize | read-only | mandatory | ADx unit RAM size. |
| 1.3.6.1.4.1.16.101.1.2.2.13.1.1.10 | ColumnrestRtmPortAdModDiagResult | read-only | mandatory | ADx unit internal diagnostics result. The bit mask is: bit 0 (LSB) RAM test bit 1 U-interface D-channel loopback test bit 2 SCC-chip D-channel loopback test bi… |
| 1.3.6.1.4.1.16.101.1.2.2.13.1.1.11 | ColumnrestRtmPortAdPortDiagResult | read-only | mandatory | ADx port internal diagnostics result. The bit mask is read from right (LSB) to left (MSB) and represents corresponding elements numbers.If bit is set to 1 the … |
| 1.3.6.1.4.1.16.101.1.2.2.13.1.1.12 | ColumnrestRtmPortAdCpMode | read-write | mandatory | CPI console pass through mode. |
| 1.3.6.1.4.1.16.101.1.2.2.13.1.1.13 | ColumnrestRtmPortAdCpSpeed | read-write | mandatory | CPI console speed value. |
| 1.3.6.1.4.1.16.101.1.2.2.13.2 | TablerestRtmAdPortTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.13.2.1 | RowrestRtmAdPortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.13.2.1.1 | ColumnrestRtmAdPortAddr | read-only | mandatory | RTM ADx port physical address in nest:slot:port:element format |
| 1.3.6.1.4.1.16.101.1.2.2.13.2.1.2 | ColumnrestRtmAdPortDiagnostics | write-only | mandatory | Remove will disconnect the element and set its start mode to off. Insert on a removed element will get the new MIB and set its start mode to auto. Reset will d… |
| 1.3.6.1.4.1.16.101.1.2.2.13.2.1.3 | ColumnrestRtmAdPortInterface | read-write | mandatory | Interface clocking type. |
| 1.3.6.1.4.1.16.101.1.2.2.13.2.1.4 | ColumnrestRtmAdPortStopBits | read-write | mandatory | Number of stop bits. |
| 1.3.6.1.4.1.16.101.1.2.2.13.2.1.5 | ColumnrestRtmAdPortGeneration | read-write | mandatory | Type of port generation. It is used in cases when end points of the connections are rather distant and passing the control (EIA) functions takes much time. Tha… |
| 1.3.6.1.4.1.16.101.1.2.2.13.2.1.6 | ColumnrestRtmAdPortContention | read-write | mandatory | Type of port contention. If f1nf1 is set, then when F1 is ON for at least 1 sec., the connection is requested. Otherwise, if F1 is OFF for at least 1 sec., the… |
| 1.3.6.1.4.1.16.101.1.2.2.13.2.1.7 | ColumnrestRtmAdPortOosOper | read-write | mandatory | Out of Sync port operations types. |
| 1.3.6.1.4.1.16.101.1.2.2.13.2.1.8 | ColumnrestRtmAdPortState | read-only | mandatory | Port state. If undefined, then it is neither configured, nor connected. If defined, then it is configured, but not connected. If online, then it is both, confi… |
| 1.3.6.1.4.1.16.101.1.2.2.13.2.1.9 | ColumnrestRtmAdPortForcedFunc | read-write | mandatory | This is a bit pattern of two bytes. The upper byte is reserved for future use. In the lower byte, the four least significant bits represent whether the functio… |
| 1.3.6.1.4.1.16.101.1.2.2.13.2.1.10 | ColumnrestRtmAdPortLoopbackType | write-only | mandatory | The commands are: adRim - ADx remote loopback command toward user equipment adLim - ADx local loopback command toward RTM/ST-50 adLimDisc - ADx local loopback … |
| 1.3.6.1.4.1.16.101.1.2.2.13.2.1.11 | ColumnrestRtmAdPortLoopbackStatus | read-only | mandatory | Status of the loopback. adLocalLl - ADx local loopback set by LL function of the interface (circuit 141) adLocalRl - ADx local loopback set by RL function of t… |
| 1.3.6.1.4.1.16.101.1.2.2.13.2.1.12 | ColumnrestRtmAdPortElecInterface | read-only | mandatory | If restRtmAdPortHardwareType returns programmable(1), then this item is able to be of read-write type of access. Otherwise it is read-only. For this release th… |
| 1.3.6.1.4.1.16.101.1.2.2.13.2.1.13 | ColumnrestRtmAdPortElIntStatus | read-only | mandatory | If ADx unit has SIPEX chip installed, then hardware type would be programmable, otherwise it would be set to nonProgrammable. |
| 1.3.6.1.4.1.16.101.1.2.2.13.2.1.14 | ColumnrestRtmAdPortParSubstitution | read-write | mandatory | This parameter is used with Async ports. When there is a parity error detected by ADx, instead of sending that character over the line it either being dropped … |
| 1.3.6.1.4.1.16.101.1.2.2.13.2.1.15 | ColumnrestRtmAdPortParSubstChar | read-write | mandatory | This is the parity substitution character for restRtmAdPortParSubstitution MIB item. |
| 1.3.6.1.4.1.16.101.1.2.2.13.2.1.16 | ColumnrestRtmAdPortPhasorStatus | read-only | mandatory | The bit mask is: bit 0 (LSB) receive underflow bit 1 receive overflow bit 2 receive empty bit 3 receive full bit 4-7 reserved bit 8 transmit underflow bit 9 tr… |
| 1.3.6.1.4.1.16.101.1.2.2.13.2.1.17 | ColumnrestRtmAdPortAdPhasorStatus | read-only | mandatory | The bit mask is: bit 0 (LSB) receive underflow bit 1 receive overflow bit 2 receive empty bit 3 receive full bit 4-7 reserved bit 8 transmit underflow bit 9 tr… |
| 1.3.6.1.4.1.16.101.1.2.2.13.2.1.18 | ColumnrestRtmAdPortAdFunctions | read-only | mandatory | The bit mask is: bit 0 (LSB) F1 (DTR) bit 1 F2 (RTS) bit 2-3 reserved bit 4 LL bit 5 RL bit 6 TM bit 7-15 (MSB) reserved. |
| 1.3.6.1.4.1.16.101.1.2.2.13.2.1.19 | ColumnrestRtmAdPortParity | read-write | mandatory | This attribute values are applicable only for ASYNC mode. |
| 1.3.6.1.4.1.16.101.1.2.2.14 | NoderestLgmPort | |||
| 1.3.6.1.4.1.16.101.1.2.2.14.1 | TablerestLgmPortTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.14.1.1 | RowrestLgmPortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.14.1.1.1 | ColumnrestLgmPortAddr | read-only | mandatory | LGM port virtual address in type:group:port format. |
| 1.3.6.1.4.1.16.101.1.2.2.14.1.1.2 | ColumnrestLgmPortLocalBERQuality | read-only | mandatory | Local Bit Error Quality value. |
| 1.3.6.1.4.1.16.101.1.2.2.14.1.1.3 | ColumnrestLgmPortBERWindowFill | read-only | mandatory | Format e.g. 10/32, 5/32. |
| 1.3.6.1.4.1.16.101.1.2.2.14.1.1.4 | ColumnrestLgmPortRemoteNodeID | read-only | mandatory | Node number that the LGM terminates on. If no remote connection has been established, then this attribute will return zero. |
| 1.3.6.1.4.1.16.101.1.2.2.14.1.1.5 | ColumnrestLgmPortRemotePortAddr | read-only | mandatory | Port or bundle address that the LGM terminates on. If no remote connection has been established, then this attribute will return zero. |
| 1.3.6.1.4.1.16.101.1.2.2.14.1.1.6 | ColumnrestLgmPortRemoteBERQuality | read-only | mandatory | Remote Bit Error Quality value. |
| 1.3.6.1.4.1.16.101.1.2.2.14.1.1.7 | ColumnrestLgmPortRemoteRevision | read-only | mandatory | Revision level on remote node. |
| 1.3.6.1.4.1.16.101.1.2.2.14.1.1.8 | ColumnrestLgmPortAvailableBw | read-only | mandatory | Available bandwith in bps. |
| 1.3.6.1.4.1.16.101.1.2.2.14.1.1.9 | ColumnrestLgmPortUsedBw | read-only | mandatory | Bandwith used in bps. |
| 1.3.6.1.4.1.16.101.1.2.2.14.1.1.10 | ColumnrestLgmPortNumCh | read-only | mandatory | Number of TDM channels. |
| 1.3.6.1.4.1.16.101.1.2.2.14.1.1.11 | ColumnrestLgmPortLgmPort | read-only | mandatory | Physical address of the LGM port. |
| 1.3.6.1.4.1.16.101.1.2.2.14.1.1.12 | ColumnrestLgmPortLinkSpeed | read-only | mandatory | Link aggregate port speed in bps. |
| 1.3.6.1.4.1.16.101.1.2.2.14.1.1.13 | ColumnrestLgmPortDiagnostics | write-only | mandatory | INTRODUCED 2.0.0 Enable on a disabled VILC will allow new channel connections to be made over this VILC. Disable will prevent any new channel connections from … |
| 1.3.6.1.4.1.16.101.1.2.2.14.1.1.14 | ColumnrestLgmPortSyncState | read-only | mandatory | INTRODUCED 2.0.0 Status of this LGM port synchronization state. |
| 1.3.6.1.4.1.16.101.1.2.2.14.2 | TablerestLgmContentsTable | not-accessible | mandatory | This table lists all of the channels on a specified LGM port. |
| 1.3.6.1.4.1.16.101.1.2.2.14.2.1 | RowrestLgmContentsEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.14.2.1.1 | ColumnrestLgmContentsAddr | read-only | mandatory | LGM Virtual Link address. |
| 1.3.6.1.4.1.16.101.1.2.2.14.2.1.2 | ColumnrestLgmContentsSequenceID | read-only | mandatory | Index to multiple channels assigned to this port. |
| 1.3.6.1.4.1.16.101.1.2.2.14.2.1.3 | ColumnrestLgmContentsSourceNodeID | read-only | mandatory | Source node ID. |
| 1.3.6.1.4.1.16.101.1.2.2.14.2.1.4 | ColumnrestLgmContentsSourceAddr | read-only | mandatory | Source address in nest:slot:port:element format. |
| 1.3.6.1.4.1.16.101.1.2.2.14.2.1.5 | ColumnrestLgmContentsDestNodeID | read-only | mandatory | Destination node ID. |
| 1.3.6.1.4.1.16.101.1.2.2.14.2.1.6 | ColumnrestLgmContentsDestAddr | read-only | mandatory | Destination address in nest:slot:port:element format. |
| 1.3.6.1.4.1.16.101.1.2.2.15 | NoderestSaf | |||
| 1.3.6.1.4.1.16.101.1.2.2.15.1 | TablerestSafTable | not-accessible | mandatory | This section of the MIB does not support getNext. |
| 1.3.6.1.4.1.16.101.1.2.2.15.1.1 | RowrestSafEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.15.1.1.1 | ColumnrestSafAddr | read-only | mandatory | SAF address. |
| 1.3.6.1.4.1.16.101.1.2.2.15.1.1.2 | ColumnrestSafStatus | read-only | mandatory | Indicates whether the SAF is synchronized or not, or whether the SAF is currently in the middle of a frame switch. |
| 1.3.6.1.4.1.16.101.1.2.2.15.1.1.3 | ColumnrestSafSubStatus | read-only | mandatory | If the SAF status is out of sync, then this attribute indicates if it is due to an error or not. If the SAF is in sync or in the middle of a frame switch, then… |
| 1.3.6.1.4.1.16.101.1.2.2.15.1.1.4 | ColumnrestSafRemoteNode | read-only | mandatory | The node in which the remote side of this SAF connection resides. |
| 1.3.6.1.4.1.16.101.1.2.2.15.1.1.5 | ColumnrestSafRemoteAddr | read-only | mandatory | The address of the remote side of this SAF connection. |
| 1.3.6.1.4.1.16.101.1.2.2.15.1.1.6 | ColumnrestSafInlNumber | read-only | mandatory | The local INL number that this SAF is located on. For a local SAF, this attribute shall return 32. |
| 1.3.6.1.4.1.16.101.1.2.2.15.1.1.7 | ColumnrestSafBandwidthAvail | read-only | mandatory | The available (unused) bandwidth in this SAF according to the NCP. |
| 1.3.6.1.4.1.16.101.1.2.2.15.1.1.8 | ColumnrestSafNumChannels | read-only | mandatory | The number of subrate channels currently connected through this SAF according to the NCP. |
| 1.3.6.1.4.1.16.101.1.2.2.15.1.1.9 | ColumnrestSafHWPhasorStatus | read-only | deprecated | DEPRECATED 2.0.1 This attribute will always return x8080, which means not applicable. |
| 1.3.6.1.4.1.16.101.1.2.2.15.1.1.10 | ColumnrestSafSWPhasorStatus | read-only | deprecated | DEPRECATED 2.0.1 This attribute will always return x8080, which means not applicable. |
| 1.3.6.1.4.1.16.101.1.2.2.15.1.1.11 | ColumnrestSafModNumChannels | read-only | mandatory | INTRODUCED 2.0.1 The number of subrate channels currently connected through this SAF according to the module that this endpoint of the SAF resides on. |
| 1.3.6.1.4.1.16.101.1.2.2.15.1.1.12 | ColumnrestSafModBandwidthAvail | read-only | mandatory | INTRODUCED 2.0.1 The available (unused) bandwidth in this SAF according to the module that this endpoint of the SAF resides on. |
| 1.3.6.1.4.1.16.101.1.2.2.15.1.1.13 | ColumnrestSafDiagnostics | write-only | mandatory | INTRODUCED 2.0.1 clearStats will clear the counters in this MIB section. setLoopback will initiate a loopback on this SAF. This will loopback all of the channe… |
| 1.3.6.1.4.1.16.101.1.2.2.15.1.1.14 | ColumnrestSafFrameSwitchLocation | read-only | mandatory | INTRODUCED 2.0.1 If a frame switch is currently occurring on this SAF, then this attribute indicates the location of that frame switch. The value is a sum with… |
| 1.3.6.1.4.1.16.101.1.2.2.15.1.1.15 | ColumnrestSafFrameSwitchIndicator | read-only | mandatory | INTRODUCED 2.0.1 Indicates if a frame switch is needed on this SAF or not. |
| 1.3.6.1.4.1.16.101.1.2.2.15.1.1.16 | ColumnrestSafRemoteStatus | read-only | mandatory | INTRODUCED 2.0.1 The view of the remote endpoint of SAF from the module that this endpoint of the SAF resides on. |
| 1.3.6.1.4.1.16.101.1.2.2.15.1.1.17 | ColumnrestSafSyncErrors | read-only | mandatory | INTRODUCED 2.0.1 The number of sync errors on this SAF. |
| 1.3.6.1.4.1.16.101.1.2.2.15.1.1.18 | ColumnrestSafOosErrors | read-only | mandatory | INTRODUCED 2.0.1 The number of OOS errors on this SAF. |
| 1.3.6.1.4.1.16.101.1.2.2.15.1.1.19 | ColumnrestSafPhasorStatus | read-only | mandatory | INTRODUCED 2.0.1 The status of the phasor for this SAF. The first octet is used to indicate transmit phasor status. The bits are interpretted as follows (bit 1… |
| 1.3.6.1.4.1.16.101.1.2.2.15.2 | TablerestSafContentsTable | not-accessible | mandatory | This section of the MIB lists all of the channels defined on an SAF. It does not support getNext. |
| 1.3.6.1.4.1.16.101.1.2.2.15.2.1 | RowrestSafContentsEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.2.15.2.1.1 | ColumnrestSafContentsAddr | read-only | mandatory | SAF address. |
| 1.3.6.1.4.1.16.101.1.2.2.15.2.1.2 | ColumnrestSafContentsSeqNum | read-only | mandatory | SAF channel number. |
| 1.3.6.1.4.1.16.101.1.2.2.15.2.1.3 | ColumnrestSafContentsSrcNode | read-only | mandatory | Source node of the channel. |
| 1.3.6.1.4.1.16.101.1.2.2.15.2.1.4 | ColumnrestSafContentsSrcAddr | read-only | mandatory | Source channel address. |
| 1.3.6.1.4.1.16.101.1.2.2.15.2.1.5 | ColumnrestSafContentsDestNode | read-only | mandatory | Destination node of the channel. |
| 1.3.6.1.4.1.16.101.1.2.2.15.2.1.6 | ColumnrestSafContentsDestAddr | read-only | mandatory | Destination channel address. |
| 1.3.6.1.4.1.16.101.1.2.2.16 | NoderestDsmPort | |||
| 1.3.6.1.4.1.16.101.1.2.2.16.1 | TablerestDsmDChPortTable | not-accessible | mandatory | This section of the MIB contains the D-channel port status. |
| 1.3.6.1.4.1.16.101.1.2.2.16.1.1 | RowrestDsmDChPortEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.4.1.16.101.1.2.2.16.1.1.1 | ColumnrestDsmDChPortAddr | read-only | mandatory | Address of D-channel port. Format is type.group.port. The server type is 131. |
| 1.3.6.1.4.1.16.101.1.2.2.16.1.1.2 | ColumnrestDsmDChPortDiagnostics | write-only | mandatory | When set to layer2Reset all B-channels associated with this D-channel will be disconnected (the D-channel itself will stay connected). |
| 1.3.6.1.4.1.16.101.1.2.2.16.1.1.3 | ColumnrestDsmDChPortNumCallsInProc | read-only | mandatory | Current number of calls in process of being completed (until CONNECT messages exchange took place). |
| 1.3.6.1.4.1.16.101.1.2.2.16.1.1.4 | ColumnrestDsmDChPortNumCallsConn | read-only | mandatory | Current number of calls connected via this D-channel. |
| 1.3.6.1.4.1.16.101.1.2.2.16.2 | TablerestDsmDChCallRealTable | not-accessible | mandatory | This section of the MIB contains information about a real call from the point of view of the DSM that its D-channel is allocated on. |
| 1.3.6.1.4.1.16.101.1.2.2.16.2.1 | RowrestDsmDChCallRealEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.4.1.16.101.1.2.2.16.2.1.1 | ColumnrestDsmDChCallRealAddr | read-only | mandatory | Address of the D-channel port associated with this real call. Format is type(131).group.port. |
| 1.3.6.1.4.1.16.101.1.2.2.16.2.1.2 | ColumnrestDsmDChCallRealBundle | read-only | mandatory | Bundle number of the B-channel used for this real call. |
| 1.3.6.1.4.1.16.101.1.2.2.16.2.1.3 | ColumnrestDsmDChCallRealCDRContents | read-only | mandatory | Call Detail Record for a real call in progress on a D-channel. Real calls are those that involve B-channels. The bytes in a CDR for a call in progress are inte… |
| 1.3.6.1.4.1.16.101.1.2.2.16.2.1.4 | ColumnrestDsmDChCallRealDiagnostics | write-only | mandatory | INTRODUCED 2.0.1 resetLayer2 will reset the Layer 2 protocol on the specified B-channel. It is not supported for Q.Sig. |
| 1.3.6.1.4.1.16.101.1.2.2.16.2.1.5 | ColumnrestDsmDChCallRealLayer2Status | read-only | mandatory | INTRODUCED 2.0.1 Indicates the Layer 2 status of a real call the point of view of the DSM. Not applicable will be returned for the D-channel bundle if the DPNS… |
| 1.3.6.1.4.1.16.101.1.2.2.16.2.1.6 | ColumnrestDsmDChCallRealLayer2State | read-only | mandatory | INTRODUCED 2.0.1 Indicates the Layer 2 protocol state of a real call from the point of view of the DSM. The values between 1 and 127 are used for DPNSS states.… |
| 1.3.6.1.4.1.16.101.1.2.2.16.2.1.7 | ColumnrestDsmDChCallRealLayer3State | read-only | mandatory | INTRODUCED 2.0.1 Indicates the Layer 3 protocol state on a real call from the point of view of the DSM. The values between 1 and 127 are used for DPNSS states.… |
| 1.3.6.1.4.1.16.101.1.2.2.16.2.1.8 | ColumnrestDsmDChCallRealTransitState | read-only | mandatory | INTRODUCED 2.0.1 Indicates the transit call control state of a real call from the point of view of the DSM. Not applicable will be returned for the D-channel b… |
| 1.3.6.1.4.1.16.101.1.2.2.16.3 | TablerestDsmDChCallVirtTable | not-accessible | mandatory | This section of the MIB contains information about a virtual call from the point of view of the DSM that its D-channel is allocated on. |
| 1.3.6.1.4.1.16.101.1.2.2.16.3.1 | RowrestDsmDChCallVirtEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.4.1.16.101.1.2.2.16.3.1.1 | ColumnrestDsmDChCallVirtAddr | read-only | mandatory | Address of the D-channel port associated with this virtual call. Format is type(131).group.port. |
| 1.3.6.1.4.1.16.101.1.2.2.16.3.1.2 | ColumnrestDsmDChCallVirtNumber | read-only | mandatory | Identity of the virtual call to be accessed. For the DPNSS protocol, this index is a bundle number in the range of 1 to 31. For the Q.Sig protocol, this index … |
| 1.3.6.1.4.1.16.101.1.2.2.16.3.1.3 | ColumnrestDsmDChCallVirtCDRContents | read-only | mandatory | Call Detail Record for a virtual call in progress on a D-channel. Virtual calls are those that do not involve B-channels. The bytes in a CDR for a call in prog… |
| 1.3.6.1.4.1.16.101.1.2.2.16.3.1.4 | ColumnrestDsmDChCallVirtDiagnostics | write-only | mandatory | INTRODUCED 2.0.1 resetLayer2 will reset the Layer 2 protocol for the specified virtual call. It is not supported for Q.Sig. |
| 1.3.6.1.4.1.16.101.1.2.2.16.3.1.5 | ColumnrestDsmDChCallVirtLayer2Status | read-only | mandatory | INTRODUCED 2.0.1 Indicates the Layer 2 status of a virtual call from the point of view of the DSM. Not applicable will be returned for the D-channel bundle if … |
| 1.3.6.1.4.1.16.101.1.2.2.16.3.1.6 | ColumnrestDsmDChCallVirtLayer2State | read-only | mandatory | INTRODUCED 2.0.1 Indicates the Layer 2 protocol state of a virtual call from the point of view of the DSM. The values between 1 and 127 are used for DPNSS stat… |
| 1.3.6.1.4.1.16.101.1.2.2.16.3.1.7 | ColumnrestDsmDChCallVirtLayer3State | read-only | mandatory | INTRODUCED 2.0.1 Indicates the Layer 3 protocol state of a virtual call from the point of view of the DSM. The values between 1 and 127 are used for DPNSS stat… |
| 1.3.6.1.4.1.16.101.1.2.2.16.3.1.8 | ColumnrestDsmDChCallVirtTransitState | read-only | mandatory | INTRODUCED 2.0.1 Indicates the transit call control state of a virtual call from the point of view of the DSM. Not applicable will be returned for the D-channe… |
| 1.3.6.1.4.1.16.101.1.2.2.17 | NoderestHwRsc | |||
| 1.3.6.1.4.1.16.101.1.2.2.17.1 | TablerestHwRscEngineTable | not-accessible | mandatory | This section of the MIB returns status of an on-board engine. |
| 1.3.6.1.4.1.16.101.1.2.2.17.1.1 | RowrestHwRscEngineEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.4.1.16.101.1.2.2.17.1.1.1 | ColumnrestHwRscEngineModAddr | read-only | mandatory | Physical address of the module this engine is located on. |
| 1.3.6.1.4.1.16.101.1.2.2.17.1.1.2 | ColumnrestHwRscEngineID | read-only | mandatory | The engine ID on the module. |
| 1.3.6.1.4.1.16.101.1.2.2.17.1.1.3 | ColumnrestHwRscEngineDiagnostics | write-only | mandatory | Insert will allow a removed engine to come online again using the current settings in the engine configuration MIB (recfHwRscEngineTable). The start mode of th… |
| 1.3.6.1.4.1.16.101.1.2.2.17.1.1.4 | ColumnrestHwRscEngineStatus | read-only | mandatory | This engine status: <removed> - logically removed, <normal> - up and running <failed> - engine failure. |
| 1.3.6.1.4.1.16.101.1.2.2.17.1.1.5 | ColumnrestHwRscEngineApplication | read-only | mandatory | Indicates the type of application allocated on this engine, if any. |
| 1.3.6.1.4.1.16.101.1.2.2.17.1.1.6 | ColumnrestHwRscEngineMaxPorts | read-only | mandatory | Maximum number of application ports on this engine. If none returns zero. |
| 1.3.6.1.4.1.16.101.1.2.2.17.1.1.7 | ColumnrestHwRscEngineNumPorts | read-only | mandatory | Number of application ports on this engine. If none returns zero. |
| 1.3.6.1.4.1.16.101.1.2.2.17.1.1.8 | ColumnrestHwRscEngineMaxSAFs | read-only | mandatory | Maximum number of SAF ports on this engine. If none returns zero. |
| 1.3.6.1.4.1.16.101.1.2.2.17.1.1.9 | ColumnrestHwRscEngineNumSAFs | read-only | mandatory | Number of SAF ports on this engine. If none returns zero. |
| 1.3.6.1.4.1.16.101.1.2.2.17.1.1.10 | ColumnrestHwRscEngineMaxSCFs | read-only | mandatory | Maximum number of SCF ports on this engine. If none returns zero. |
| 1.3.6.1.4.1.16.101.1.2.2.17.1.1.11 | ColumnrestHwRscEngineNumSCFs | read-only | mandatory | Number of SCF ports on this engine. If none returns zero. |
| 1.3.6.1.4.1.16.101.1.2.2.17.1.1.12 | ColumnrestHwRscEngineMaxLoad | read-only | mandatory | Indicates the total load capacity of this engine. |
| 1.3.6.1.4.1.16.101.1.2.2.17.1.1.13 | ColumnrestHwRscEngineCurLoad | read-only | mandatory | Indicates the percentage of the total load capacity of this engine that is currently in use. |
| 1.3.6.1.4.1.16.101.1.2.2.17.1.1.14 | ColumnrestHwRscEngineSubStatus | read-only | mandatory | INTRODUCED 2.0.1 If an engine is in a failed state, then this value will indicate the reason for the failure. If the engine is not failed, then none will be re… |
| 1.3.6.1.4.1.16.101.1.2.3 | NodereStatistics | |||
| 1.3.6.1.4.1.16.101.1.2.3.1 | NoderestStatPort | |||
| 1.3.6.1.4.1.16.101.1.2.3.1.1 | TablerestStatPortT1mTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.1.1 | RowrestStatPortT1mEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.1.1.1 | ColumnrestStatPortT1mAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.1.1.2 | ColumnrestStatPortT1mIndex | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.1.1.3 | ColumnrestStatPortT1mStartTime | read-only | mandatory | Indicates when this statistics interval was started. |
| 1.3.6.1.4.1.16.101.1.2.3.1.1.1.4 | ColumnrestStatPortT1mErrSec | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.1.1.5 | ColumnrestStatPortT1mSevErrSec | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.1.1.6 | ColumnrestStatPortT1mBstyErrSec | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.1.1.7 | ColumnrestStatPortT1mUnavailSec | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.1.1.8 | ColumnrestStatPortT1mLostFrame | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.1.1.9 | ColumnrestStatPortT1mControlMode | write-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.2 | TablerestStatPortE1mTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.2.1 | RowrestStatPortE1mEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.2.1.1 | ColumnrestStatPortE1mAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.2.1.2 | ColumnrestStatPortE1mIndex | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.2.1.3 | ColumnrestStatPortE1mStartTime | read-only | mandatory | Indicates when this statistics interval was started. |
| 1.3.6.1.4.1.16.101.1.2.3.1.2.1.4 | ColumnrestStatPortE1mErrSec | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.2.1.5 | ColumnrestStatPortE1mSevErrSec | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.2.1.6 | ColumnrestStatPortE1mBstyErrSec | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.2.1.7 | ColumnrestStatPortE1mUnavailSec | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.2.1.8 | ColumnrestStatPortE1mLostFrame | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.2.1.9 | ColumnrestStatPortE1mControlMode | write-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.3 | TablerestStatPortPktTable | not-accessible | mandatory | This section of the MIB does not support getNext. |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1 | RowrestStatPortPktEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1.1 | ColumnrestStatPortPktAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1.2 | ColumnrestStatPortPktControlMode | write-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1.3 | ColumnrestStatPortPktSegmentSent | read-only | mandatory | Segments sent from the network to the user device on any of the DLCIs on this port. |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1.4 | ColumnrestStatPortPktSegmentRecv | read-only | mandatory | Segments received at the network from the user device on any of the DLCIs on this port. |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1.5 | ColumnrestStatPortPktOctetSent | read-only | mandatory | Octets sent from the network to the user device on any of the DLCIs on this port. |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1.6 | ColumnrestStatPortPktOctetRecv | read-only | mandatory | Octets received at the network from the user device on any of the DLCIs on this port. |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1.7 | ColumnrestStatPortPktDlciDiscard | read-only | mandatory | Number of frames discarded because the destination DLCI was not active. |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1.8 | ColumnrestStatPortPktBadAddrDiscard | read-only | mandatory | Number of frames discarded because the address field was not two bytes in length. |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1.9 | ColumnrestStatPortPktOvrszeDiscard | read-only | mandatory | Number of frames received from the user device that were discarded because they exceeded the maximum frame size. |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1.10 | ColumnrestStatPortPktUnderszeDiscard | read-only | mandatory | Number of HDLC frames discarded because the frame was too short. |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1.11 | ColumnrestStatPortPktCRCDiscard | read-only | mandatory | Number of HDLC frames discarded because the CRC was bad. |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1.12 | ColumnrestStatPortPktSwOvrRunDiscard | read-only | mandatory | Number of frames discarded because of port software buffer over run. |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1.13 | ColumnrestStatPortPktUnderRunDiscard | read-only | mandatory | Number of HDLC frames discarded because of under run. |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1.14 | ColumnrestStatPortPktAbortDiscard | read-only | mandatory | Number of HDLC frames discarded because frame abort was received. |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1.15 | ColumnrestStatPortPktHwOvrRunDiscard | read-only | mandatory | Number of frames discarded because of port hardware over run. |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1.16 | ColumnrestStatPortPktLmiSegmentSent | read-only | mandatory | Number of LMI message segments sent. |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1.17 | ColumnrestStatPortPktLmiSegmentRecv | read-only | mandatory | Number of LMI message segments received. |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1.18 | ColumnrestStatPortPktLmiSyntaxErr | read-only | mandatory | Number of LMI messages dropped due to syntax errors. |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1.19 | ColumnrestStatPortPktLmiWrongSeq | read-only | mandatory | Number of LMI messages dropped due to incorrect sequence numbers. |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1.20 | ColumnrestStatPortPktLmiPollTimeOut | read-only | mandatory | Number of LMI messages dropped due to poll time outs. The parameter recfFrPortLmiPollingTimer controls the duration of this timer. |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1.21 | ColumnrestStatPortPktLmiWaitTimeOut | read-only | mandatory | Number of LMI messages dropped due to wait time outs. The parameter recfFrPortLmiWaitingTimer controls the duration of this timer. |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1.22 | ColumnrestStatPortPktLmiTxSeqNum | read-only | mandatory | LMI transmit sequence number. |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1.23 | ColumnrestStatPortPktLmiRxSeqNum | read-only | mandatory | LMI receive sequence number. |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1.24 | ColumnrestStatPortPktLmiNumGoodEvents | read-only | mandatory | Number of good LMI events within the current monitor window. The size of this window is controlled by the recfFrPortLmiMonitoredEvents attribute. |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1.25 | ColumnrestStatPortPktLmiNumBadEvents | read-only | mandatory | Number of bad LMI events within the current monitor window. The size of this window is controlled by the recfFrPortLmiMonitoredEvents attribute. |
| 1.3.6.1.4.1.16.101.1.2.3.1.3.1.26 | ColumnrestStatPortPktLmiEventHistory | read-only | mandatory | Shows the last eight LMI events. Each event requires four bits. Bits 1 (lsb), 2, 3 and 4 of the last octet represent the most recent event. The event values ar… |
| 1.3.6.1.4.1.16.101.1.2.3.1.4 | TablerestStatPortAsmX50Table | not-accessible | mandatory | This section of the MIB does not support getNext. |
| 1.3.6.1.4.1.16.101.1.2.3.1.4.1 | RowrestStatPortAsmX50Entry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.4.1.1 | ColumnrestStatPortAsmX50Addr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.4.1.2 | ColumnrestStatPortAsmX50Control | write-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.4.1.3 | ColumnrestStatPortAsmX50RxFrameErrors | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.4.1.4 | ColumnrestStatPortAsmX50LocalOs | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.4.1.5 | ColumnrestStatPortAsmX50RemoteOs | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.5 | TablerestStatPortRtmTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.5.1 | RowrestStatPortRtmEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.5.1.1 | ColumnrestStatPortRtmAddr | read-only | mandatory | RTM port physical address in nest:slot:port format |
| 1.3.6.1.4.1.16.101.1.2.3.1.5.1.2 | ColumnrestStatPortRtmControl | write-only | mandatory | Clears the statistics of a port. |
| 1.3.6.1.4.1.16.101.1.2.3.1.5.1.3 | ColumnrestStatPortRtmUIFarEndBlkErr | read-only | mandatory | Count of RTM port U-interface far end block errors. It is a count that is being kept by RTM module. |
| 1.3.6.1.4.1.16.101.1.2.3.1.5.1.4 | ColumnrestStatPortRtmUINearEndBlkErr | read-only | mandatory | Count of RTM port U-interface near end block errors. It is a count that is being kept by RTM module. |
| 1.3.6.1.4.1.16.101.1.2.3.1.5.1.5 | ColumnrestStatPortRtmAdUIFarEndBlkErr | read-only | mandatory | Count of RTM port U-interface far end block errors. It is a count that is being kept by RTM AD module. |
| 1.3.6.1.4.1.16.101.1.2.3.1.5.1.6 | ColumnrestStatPortRtmAdUINrEndBlkErr | read-only | mandatory | Count of RTM port U-interface near end block errors. It is a count that is being kept by RTM AD module. |
| 1.3.6.1.4.1.16.101.1.2.3.1.5.1.7 | ColumnrestStatPortRtmOOSTransitions | read-only | mandatory | Count of RTM port OOS transition occurances. It is a summary of this events for all the elements on the port . |
| 1.3.6.1.4.1.16.101.1.2.3.1.6 | TablerestStatPortAsmVoiceTable | not-accessible | mandatory | This section of the MIB does not support getNext. |
| 1.3.6.1.4.1.16.101.1.2.3.1.6.1 | RowrestStatPortAsmVoiceEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.6.1.1 | ColumnrestStatPortAsmVoiceChanAddr | read-only | mandatory | Address of T1M/E1M bundle which is being used by this port while connected. If disconnected returns error. |
| 1.3.6.1.4.1.16.101.1.2.3.1.6.1.2 | ColumnrestStatPortAsmVoiceControl | write-only | mandatory | Clear stats will clear all statistics for specified port. |
| 1.3.6.1.4.1.16.101.1.2.3.1.6.1.3 | ColumnrestStatPortAsmVoiceFrameOOSs | read-only | mandatory | Frame OOS statistics. |
| 1.3.6.1.4.1.16.101.1.2.3.1.6.1.4 | ColumnrestStatPortAsmVoiceSignalOOSs | read-only | mandatory | Signaling OOS statistics. |
| 1.3.6.1.4.1.16.101.1.2.3.1.6.1.5 | ColumnrestStatPortAsmVoiceHighBERs | read-only | mandatory | HBER statistics. |
| 1.3.6.1.4.1.16.101.1.2.3.1.7 | TablerestStatPortLgmTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.7.1 | RowrestStatPortLgmEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.1.7.1.1 | ColumnrestStatPortLgmAddr | read-only | mandatory | Address of the LGM port in type:group:port format. |
| 1.3.6.1.4.1.16.101.1.2.3.1.7.1.2 | ColumnrestStatPortLgmControlMode | write-only | mandatory | Clears the statistics of a port. |
| 1.3.6.1.4.1.16.101.1.2.3.1.7.1.3 | ColumnrestStatPortLgmBadSync | read-only | mandatory | Number of bad sync count received. |
| 1.3.6.1.4.1.16.101.1.2.3.1.7.1.4 | ColumnrestStatPortLgmOosCount | read-only | mandatory | Number of out of sync conditions. |
| 1.3.6.1.4.1.16.101.1.2.3.1.7.1.5 | ColumnrestStatPortLgmFrameSent | read-only | mandatory | Number of frames transmitted. |
| 1.3.6.1.4.1.16.101.1.2.3.1.7.1.6 | ColumnrestStatPortLgmFrameRecd | read-only | mandatory | Number of frames received. |
| 1.3.6.1.4.1.16.101.1.2.3.1.7.1.7 | ColumnrestStatPortLgmFrameReTx | read-only | mandatory | Number of frames retransmitted. |
| 1.3.6.1.4.1.16.101.1.2.3.1.7.1.8 | ColumnrestStatPortLgmFrameNak | read-only | mandatory | Number of NACKs sent. |
| 1.3.6.1.4.1.16.101.1.2.3.1.7.1.9 | ColumnrestStatPortLgmSabmSent | read-only | mandatory | Number of SABMs sent. |
| 1.3.6.1.4.1.16.101.1.2.3.1.7.1.10 | ColumnrestStatPortLgmSabmRecd | read-only | mandatory | Number of SABMs received. |
| 1.3.6.1.4.1.16.101.1.2.3.1.7.1.11 | ColumnrestStatPortLgmRnrSent | read-only | mandatory | Number of Receiver_Not_Ready sent. |
| 1.3.6.1.4.1.16.101.1.2.3.1.7.1.12 | ColumnrestStatPortLgmRnrRecd | read-only | mandatory | Number of Receiver_Not_Ready received. |
| 1.3.6.1.4.1.16.101.1.2.3.1.8 | NoderestStatPortDsm | |||
| 1.3.6.1.4.1.16.101.1.2.3.1.8.1 | TablerestStatPortDsmDChTable | not-accessible | mandatory | This section contains the call statistics maintained for each D-channel port. There are also HDLC statistics maintained for D-channel ports. These are defined … |
| 1.3.6.1.4.1.16.101.1.2.3.1.8.1.1 | RowrestStatPortDsmDChEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.4.1.16.101.1.2.3.1.8.1.1.1 | ColumnrestStatPortDsmDChAddr | read-only | mandatory | Address of the D-channel in type.group.port format. The server type is 131. |
| 1.3.6.1.4.1.16.101.1.2.3.1.8.1.1.2 | ColumnrestStatPortDsmDChControlMode | write-only | mandatory | Setting this field to clearStats will reset all of the counters in this MIB section to zero. |
| 1.3.6.1.4.1.16.101.1.2.3.1.8.1.1.3 | ColumnrestStatPortDsmDChOrigAttempts | read-only | mandatory | Number of calls attempted by the ISPBX over this D-channel. This includes both successful and failed calls. |
| 1.3.6.1.4.1.16.101.1.2.3.1.8.1.1.4 | ColumnrestStatPortDsmDChTermAttempts | read-only | mandatory | Number of calls attempted by the ST network to the ISPBX connected to this D-channel. This includes both successful and failed calls. |
| 1.3.6.1.4.1.16.101.1.2.3.1.8.1.1.5 | ColumnrestStatPortDsmDChPbxLayer2Errs | read-only | mandatory | Number of layer 2 errors detected by the DSM on this D-channel. |
| 1.3.6.1.4.1.16.101.1.2.3.1.8.1.1.6 | ColumnrestStatPortDsmDChPbxLayer3Errs | read-only | mandatory | Number of layer 3 errors detected by the DSM on this D-channel. |
| 1.3.6.1.4.1.16.101.1.2.3.1.8.1.1.7 | ColumnrestStatPortDsmDChPbxLinkResets | read-only | mandatory | Number of layer 2 reset commands received from the ISPBX on this D-channel. |
| 1.3.6.1.4.1.16.101.1.2.3.1.8.1.1.8 | ColumnrestStatPortDsmDChPbxDisconns | read-only | mandatory | Number of calls disconnected on this D-channel due to a request from the local ISPBX. |
| 1.3.6.1.4.1.16.101.1.2.3.1.8.1.1.9 | ColumnrestStatPortDsmDChPbxUnkExchs | read-only | mandatory | Number of call attempts originating from the local ISPBX that failed because the called number did not fall into any exchange codes to which the DSM has a rout… |
| 1.3.6.1.4.1.16.101.1.2.3.1.8.1.1.10 | ColumnrestStatPortDsmDChPbxNoBws | read-only | mandatory | Number of call attempts originating from the local ISPBX that failed because no route could be found between the source and destination nodes with enough bandw… |
| 1.3.6.1.4.1.16.101.1.2.3.1.8.1.1.11 | ColumnrestStatPortDsmDChPbxNoCmprs | read-only | mandatory | Number of call attempts originating from the local ISPBX that failed because a compression resource was not available in either the source or destination node … |
| 1.3.6.1.4.1.16.101.1.2.3.1.8.1.1.12 | ColumnrestStatPortDsmDChPbxNoBchs | read-only | mandatory | Number of call attempts originating from the local ISPBX that failed because there were no available B-channels that could handle an outgoing call. |
| 1.3.6.1.4.1.16.101.1.2.3.1.8.1.1.13 | ColumnrestStatPortDsmDChPbxOtherFails | read-only | mandatory | Number of call attempts originating from the local ISPBX that failed for any reason not covered by the other statistics in this MIB section. |
| 1.3.6.1.4.1.16.101.1.2.3.1.8.1.1.14 | ColumnrestStatPortDsmDChNetDisconns | read-only | mandatory | Number of calls disconnected on this D-channel due to a request from the ST network. |
| 1.3.6.1.4.1.16.101.1.2.3.1.8.1.1.15 | ColumnrestStatPortDsmDChNetOtherFails | read-only | mandatory | Number of calls attempting to terminate on the local ISPBX that failed for any reason not covered by the other statistics in this MIB section. |
| 1.3.6.1.4.1.16.101.1.2.3.2 | NoderestStatCh | |||
| 1.3.6.1.4.1.16.101.1.2.3.2.1 | TablerestStatChPktTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1 | RowrestStatChPktEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.1 | ColumnrestStatChPktAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.2 | ColumnrestStatChPktSourceNodeID | read-only | mandatory | Source node of the channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.3 | ColumnrestStatChPktSourceChAddr | read-only | mandatory | Source address of the channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.4 | ColumnrestStatChPktDestNodeID | read-only | mandatory | Destination node of the channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.5 | ColumnrestStatChPktDestChAddr | read-only | mandatory | Destination address of the channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.6 | ColumnrestStatChPktControlMode | write-only | mandatory | Clear stats will clear all of the statistics for the specified frame relay channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.7 | ColumnrestStatChPktSegmentsToUser | read-only | mandatory | Number of segments currently queued to be sent to the user device. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.8 | ColumnrestStatChPktSegmentsToNetwork | read-only | mandatory | Number of segments currently queued to be sent into the network bound for the other end of the frame relay channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.9 | ColumnrestStatChPktYellowThreshold | read-only | mandatory | Number of segments that can be in any queue before that channel is in yellow congestion mode. This value is 40% of the critical threshold. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.10 | ColumnrestStatChPktRedThreshold | read-only | mandatory | Number of segments that can be in any queue before that channel is in red congestion mode. This value is 86% of the critical threshold. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.11 | ColumnrestStatChPktCritThreshold | read-only | mandatory | Number of segments that can be in any queue before that channel is in critical congestion mode. This value is the maximum number of segments that the queue can… |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.12 | ColumnrestStatChPktPortCongMode | read-only | mandatory | Congestion mode of the port queue, which forwards segments to the user device. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.13 | ColumnrestStatChPktNetCongMode | read-only | mandatory | Congestion mode of the network queue, which forwards segments to the network, destined for the other endpoint of the frame relay channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.14 | ColumnrestStatChPktRemoteCongMode | read-only | mandatory | Worst congestion mode of all of the segment queues between this node and the other endpoint of the frame relay channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.15 | ColumnrestStatChPktCIRCredit | read-only | mandatory | Number of CIR octets that can be sent per second. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.16 | ColumnrestStatChPktEIRCredit | read-only | mandatory | Number of EIR octets that can be sent per second. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.17 | ColumnrestStatChPktFECNSent | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.18 | ColumnrestStatChPktBECNSent | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.19 | ColumnrestStatChPktPortCIRSegSent | read-only | mandatory | Number of CIR segments sent from the network to the user device. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.20 | ColumnrestStatChPktPortCIRSegRcv | read-only | mandatory | Number of CIR segments received from the user device to be sent to the network. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.21 | ColumnrestStatChPktPortEIRSegSent | read-only | mandatory | Number of EIR segments sent from the network to the user device. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.22 | ColumnrestStatChPktPortEIRSegRcv | read-only | mandatory | Number of EIR segments received from the user device to be sent to the network. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.23 | ColumnrestStatChPktPortCIROctetSent | read-only | mandatory | Number of CIR octets sent from the network to the user device. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.24 | ColumnrestStatChPktPortCIROctetRcv | read-only | mandatory | Number of CIR octets received from the user device to be sent to the network. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.25 | ColumnrestStatChPktPortEIROctetSent | read-only | mandatory | Number of EIR octets sent from the network to the user device. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.26 | ColumnrestStatChPktPortEIROctetRcv | read-only | mandatory | Number of EIR octets received from the user device to be sent to the network. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.27 | ColumnrestStatChPktPortCIRSegDrops | read-only | mandatory | Number of CIR segments received from the user device that have been dropped. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.28 | ColumnrestStatChPktPortEIRSegDrops | read-only | mandatory | Number of EIR segments received from the user device that have been dropped. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.29 | ColumnrestStatChPktPortCIROctetDrops | read-only | mandatory | Number of CIR octets received from the user device that have been dropped. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.30 | ColumnrestStatChPktPortEIROctetDrops | read-only | mandatory | Number of EIR octets received from the user device that have been dropped. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.31 | ColumnrestStatChPktNetCIRSegSent | read-only | mandatory | Number of CIR segments sent from the user device to the network. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.32 | ColumnrestStatChPktNetCIRSegRcv | read-only | mandatory | Number of CIR segments received from the network to be sent to the user device. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.33 | ColumnrestStatChPktNetEIRSegSent | read-only | mandatory | Number of EIR segments sent from the user device to the network. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.34 | ColumnrestStatChPktNetEIRSegRcv | read-only | mandatory | Number of EIR segments received from the network to be sent to the user device. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.35 | ColumnrestStatChPktNetCIROctetSent | read-only | mandatory | Number of CIR octets sent from the user device to the network. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.36 | ColumnrestStatChPktNetCIROctetRcv | read-only | mandatory | Number of CIR octets received from the network to be sent to the user device. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.37 | ColumnrestStatChPktNetEIROctetSent | read-only | mandatory | Number of EIR octets sent from the user device to the network. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.38 | ColumnrestStatChPktNetEIROctetRcv | read-only | mandatory | Number of EIR octets received from the network to be sent to the user device. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.39 | ColumnrestStatChPktNetCIRSegDrops | read-only | mandatory | Number of CIR segments received from the network that have been dropped. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.40 | ColumnrestStatChPktNetEIRSegDrops | read-only | mandatory | Number of EIR segments received from the network that have been dropped. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.41 | ColumnrestStatChPktNetCIROctetDrops | read-only | mandatory | Number of CIR octets received from the network that have been dropped. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.42 | ColumnrestStatChPktNetEIROctetDrops | read-only | mandatory | Number of EIR octets received from the network that have been dropped. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.43 | ColumnrestStatChPktSegEIRDiscard | read-only | mandatory | Number of segments discarded because the system was unable to send EIR traffic. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.44 | ColumnrestStatChPktSegSeqDiscard | read-only | mandatory | Number of segments discarded because a sequence error was detected. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.45 | ColumnrestStatChPktSegCongPortDiscard | read-only | mandatory | Number of segments discarded because of congestion on the queue with segments to send to the user device. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.46 | ColumnrestStatChPktSegCongNetDiscard | read-only | mandatory | Number of segments discarded because of congestion on the queue with segments to send to the network. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.47 | ColumnrestStatChPktSegExcDiscard | read-only | mandatory | Number of segments discarded because the available CIR or EIR credit has been exceeded. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.48 | ColumnrestStatChPktSegUnderszDiscard | read-only | mandatory | Number of segments discarded because the size was less than the minimum. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.49 | ColumnrestStatChPktSegV120ErrDiscard | read-only | mandatory | Number of segments discarded because the V120 header was bad (used with Ad-10 only). |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.50 | ColumnrestStatChPktSegInacPortDiscard | read-only | mandatory | Number of segments discarded because the destination DLCI was inactive. |
| 1.3.6.1.4.1.16.101.1.2.3.2.1.1.51 | ColumnrestStatChPktSegInacNetDiscard | read-only | mandatory | Number of segments discarded because this DLCI was inactive. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2 | TablerestStatChPktBypTable | not-accessible | mandatory | This section of the MIB does not support getNext. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1 | RowrestStatChPktBypEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.1 | ColumnrestStatChPktBypNodeID | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.2 | ColumnrestStatChPktBypAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.3 | ColumnrestStatChPktBypSourceNodeID | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.4 | ColumnrestStatChPktBypSourceChAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.5 | ColumnrestStatChPktBypDestNodeID | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.6 | ColumnrestStatChPktBypDestChAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.7 | ColumnrestStatChPktBypControlMode | write-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.8 | ColumnrestStatChPktBypSegmentsToSrc | read-only | mandatory | Number of segments currently queued to be sent to the source of this channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.9 | ColumnrestStatChPktBypSegmentsToDst | read-only | mandatory | Number of segments currently queued to be sent to the destination of this channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.10 | ColumnrestStatChPktBypYellowThreshold | read-only | mandatory | Number of segments that can be in any queue before that channel is in yellow congestion mode. This value is 40% of the critical threshold. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.11 | ColumnrestStatChPktBypRedThreshold | read-only | mandatory | Number of segments that can be in any queue before that channel is in red congestion mode. This value is 86% of the critical threshold. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.12 | ColumnrestStatChPktBypCritThreshold | read-only | mandatory | Number of segments that can be in any queue before that channel is in critical congestion mode. This value is the maximum number of segments that the queue can… |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.13 | ColumnrestStatChPktBypInCongMode | read-only | mandatory | Congestion mode of the in queue, which forwards segments to the source of this channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.14 | ColumnrestStatChPktBypOutCongMode | read-only | mandatory | Congestion mode of the out queue, which forwards segments to the destination of this channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.15 | ColumnrestStatChPktBypInCIRSegSent | read-only | mandatory | Number of CIR segments sent from this node to the source of this channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.16 | ColumnrestStatChPktBypInCIRSegRcv | read-only | mandatory | Number of CIR segments received at this node from the source of this channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.17 | ColumnrestStatChPktBypInEIRSegSent | read-only | mandatory | Number of EIR segments sent from this node to the source of this channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.18 | ColumnrestStatChPktBypInEIRSegRcv | read-only | mandatory | Number of EIR segments received at this node from the source of this channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.19 | ColumnrestStatChPktBypInCIROctetSent | read-only | mandatory | Number of CIR octets sent from this node to the source of this channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.20 | ColumnrestStatChPktBypInCIROctetRcv | read-only | mandatory | Number of CIR octets received at this node from the source of this channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.21 | ColumnrestStatChPktBypInEIROctetSent | read-only | mandatory | Number of EIR octets sent from this node to the source of this channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.22 | ColumnrestStatChPktBypInEIROctetRcv | read-only | mandatory | Number of EIR octets received at this node from the source of this channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.23 | ColumnrestStatChPktBypInCIRSegDrop | read-only | mandatory | Number of CIR segments received at this node from the source of this channel that have been dropped. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.24 | ColumnrestStatChPktBypInEIRSegDrop | read-only | mandatory | Number of EIR segments received at this node from the source of this channel that have been dropped. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.25 | ColumnrestStatChPktBypInCIROctetDrop | read-only | mandatory | Number of CIR octets received at this node from the source of this channel that have been dropped. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.26 | ColumnrestStatChPktBypInEIROctetDrop | read-only | mandatory | Number of EIR octets received at this node from the source of this channel that have been dropped. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.27 | ColumnrestStatChPktBypOutCIRSegSent | read-only | mandatory | Number of CIR segments sent from this node to the destination of this channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.28 | ColumnrestStatChPktBypOutCIRSegRcv | read-only | mandatory | Number of CIR segments received at this node from the destination of this channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.29 | ColumnrestStatChPktBypOutEIRSegSent | read-only | mandatory | Number of EIR segments sent from this node to the destination of this channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.30 | ColumnrestStatChPktBypOutEIRSegRcv | read-only | mandatory | Number of EIR segments received at this node from the destination of this channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.31 | ColumnrestStatChPktBypOutCIROctetSent | read-only | mandatory | Number of CIR octets sent from this node to the destination of this channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.32 | ColumnrestStatChPktBypOutCIROctetRcv | read-only | mandatory | Number of CIR octets received at this node from the destination of this channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.33 | ColumnrestStatChPktBypOutEIROctetSent | read-only | mandatory | Number of EIR octets sent from this node to the destination of this channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.34 | ColumnrestStatChPktBypOutEIROctetRcv | read-only | mandatory | Number of EIR octets received at this node from the destination of this channel. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.35 | ColumnrestStatChPktBypOutCIRSegDrop | read-only | mandatory | Number of CIR segments received at this node from the destination of this channel that have been dropped. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.36 | ColumnrestStatChPktBypOutEIRSegDrop | read-only | mandatory | Number of EIR segments received at this node from the destination of this channel that have been dropped. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.37 | ColumnrestStatChPktBypOutCIROctetDrop | read-only | mandatory | Number of CIR octets received at this node from the destination of this channel that have been dropped. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.38 | ColumnrestStatChPktBypOutEIROctetDrop | read-only | mandatory | Number of EIR octets received at this node from the destination of this channel that have been dropped. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.39 | ColumnrestStatChPktBypSegSrcEIRDisc | read-only | mandatory | Number of segments from the source of this channel that were discarded because the system was unable to send EIR traffic. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.40 | ColumnrestStatChPktBypSegDstEIRDisc | read-only | mandatory | Number of segments from the destination of this channel that were discarded because the system was unable to send EIR traffic. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.41 | ColumnrestStatChPktBypSegSrcDstConDsc | read-only | mandatory | Number of segments from the source of this channel that were discarded because the queue of segments to send to the destination was congested. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.42 | ColumnrestStatChPktBypSegDstSrcConDsc | read-only | mandatory | Number of segments from the destination of this channel that were discarded because the queue of segments to send to the source was congested. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.43 | ColumnrestStatChPktBypSegInacSrcDisc | read-only | mandatory | Number of segments discarded because the source of this channel was inactive. |
| 1.3.6.1.4.1.16.101.1.2.3.2.2.1.44 | ColumnrestStatChPktBypSegInacDstDisc | read-only | mandatory | Number of segments discarded because the destination of this channel was inactive. |
| 1.3.6.1.4.1.16.101.1.2.3.3 | NoderestStatInl | |||
| 1.3.6.1.4.1.16.101.1.2.3.3.1 | TablerestStatInlTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.3.1.1 | RowrestStatInlEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.3.1.1.1 | ColumnrestStatInlNumber | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.3.1.1.2 | ColumnrestStatInlIndex | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.3.1.1.3 | ColumnrestStatInlStartTime | not-accessible | mandatory | Indicates when this statistics interval was started. |
| 1.3.6.1.4.1.16.101.1.2.3.3.1.1.4 | ColumnrestStatInlPktOctetSent | read-only | mandatory | Number of octets sent across the INL. A value of 0 means that no data is available for that interval. |
| 1.3.6.1.4.1.16.101.1.2.3.3.1.1.5 | ColumnrestStatInlPktOctetRcv | read-only | mandatory | Number of octets received across the INL. A value of 0 means that no data is available for that interval. |
| 1.3.6.1.4.1.16.101.1.2.3.4 | NoderestStatAd10 | |||
| 1.3.6.1.4.1.16.101.1.2.3.4.1 | TablerestStatAd10DataPortTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.1.1 | RowrestStatAd10DataPortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.1.1.1 | ColumnrestStatAd10DataPortAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.1.1.2 | ColumnrestStatAd10DataPortControl | write-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.1.1.3 | ColumnrestStatAd10DataPortTxTotFrames | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.1.1.4 | ColumnrestStatAd10DataPortRxTotFrames | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.1.1.5 | ColumnrestStatAd10DataPortRxFrSeqErr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.1.1.6 | ColumnrestStatAd10DataPortRxFrHdrErr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.1.1.7 | ColumnrestStatAd10DataPortRxCongDisc | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.1.1.8 | ColumnrestStatAd10DataPortTxCongDisc | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.1.1.9 | ColumnrestStatAd10DataPortRxBecnCount | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.1.1.10 | ColumnrestStatAd10DataPortTxBecnCount | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.1.1.11 | ColumnrestStatAd10DataPortTxSCCOvrRun | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.1.1.12 | ColumnrestStatAd10DataPortRxSCCUndRun | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.1.1.13 | ColumnrestStatAd10DataPortTxSCCAbort | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.1.1.14 | ColumnrestStatAd10DataPortTxFrOvrSize | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.1.1.15 | ColumnrestStatAd10DataPortTxFifoFlCtl | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.1.1.16 | ColumnrestStatAd10DataPortRxMinSegHt | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.1.1.17 | ColumnrestStatAd10DataPortBertSynLoss | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.1.1.18 | ColumnrestStatAd10DataPortBertByteCnt | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.1.1.19 | ColumnrestStatAd10DataPortBertBitErr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.2 | TablerestStatAd10VoicePortTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.2.1 | RowrestStatAd10VoicePortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.2.1.1 | ColumnrestStatAd10VoicePortAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.2.1.2 | ColumnrestStatAd10VoicePortControl | write-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.2.1.3 | ColumnrestStatAd10VoicePortHber | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.2.1.4 | ColumnrestStatAd10VoicePortSyncLoss | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.2.1.5 | ColumnrestStatAd10VoicePortBertByte | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.2.1.6 | ColumnrestStatAd10VoicePortBertBitErr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.3 | TablerestStatAd10PktBandTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.3.1 | RowrestStatAd10PktBandEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.3.1.1 | ColumnrestStatAd10PktBandAddr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.3.1.2 | ColumnrestStatAd10PktBandControl | write-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.3.1.3 | ColumnrestStatAd10PktBandTxTotFrames | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.3.1.4 | ColumnrestStatAd10PktBandRxTotFrames | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.3.1.5 | ColumnrestStatAd10PktBandRxFrErr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.3.1.6 | ColumnrestStatAd10PktBandRxSCCOvrRun | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.3.1.7 | ColumnrestStatAd10PktBandTxSCCUndRun | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.3.1.8 | ColumnrestStatAd10PktBandRxSCCAbort | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.3.1.9 | ColumnrestStatAd10PktBandRxInvDlci | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.3.1.10 | ColumnrestStatAd10PktBandRxFrOvrSize | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.4.3.1.11 | ColumnrestStatAd10PktBandRxCrcErr | read-only | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.5 | NoderestStatModule | |||
| 1.3.6.1.4.1.16.101.1.2.3.5.1 | TablerestStatModDsmTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.2.3.5.1.1 | RowrestStatModDsmEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.4.1.16.101.1.2.3.5.1.1.1 | ColumnrestStatModDsmAddr | read-only | mandatory | Address of a DSM module. The format of the address is nest.slot. |
| 1.3.6.1.4.1.16.101.1.2.3.5.1.1.2 | ColumnrestStatModDsmControlMode | write-only | mandatory | Setting this field to clearStats will reset all of the counters in this MIB section to zero. |
| 1.3.6.1.4.1.16.101.1.2.3.5.1.1.3 | ColumnrestStatModDsmRejectOrigCalls | read-only | mandatory | Number of calls initiated by a local ISPBX that were rejected for any reason. |
| 1.3.6.1.4.1.16.101.1.2.3.5.1.1.4 | ColumnrestStatModDsmRejectTermCalls | read-only | mandatory | Number of calls initiated by a DSM that would be terminated on this DSM and that were rejected for any reason. |
| 1.3.6.1.4.1.16.101.1.3 | Nodealarm | |||
| 1.3.6.1.4.1.16.101.1.3.1 | NodealPartitionHeader | |||
| 1.3.6.1.4.1.16.101.1.3.1.1 | ScalaralPartitionControl | write-only | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.4.1.16.101.1.3.1.2 | ScalaralPartitionCRCCheck | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.3.1.3 | ScalaralPartitionFlushMode | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.4.1.16.101.1.3.2 | NodealSystemProfile | |||
| 1.3.6.1.4.1.16.101.1.3.2.1 | ScalaralSysLogSize | read-write | mandatory | Parameter Type = Immediate. Assign the size to each of the 32 alarm logs. The sizes are specified in units of Kbytes. The total size cannot exceed 128K bytes. |
| 1.3.6.1.4.1.16.101.1.3.2.2 | ScalaralSysLogSizeAvailable | read-only | mandatory | Parameter Type = Internal. The amount of remaining alarm log space in units of Kbytes. |
| 1.3.6.1.4.1.16.101.1.3.3 | TablealLogTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.3.3.1 | RowalLogEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.3.3.1.1 | ColumnalLogIndex | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.3.3.1.2 | ColumnalLogDiagnostics | write-only | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.4.1.16.101.1.3.3.1.3 | ColumnalLogState | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.3.3.1.4 | ColumnalLogTotalEntries | read-only | mandatory | Parameter Type = Internal. The number of outstanding alarms contained within this alarm log. |
| 1.3.6.1.4.1.16.101.1.3.3.1.5 | ColumnalLogAvailableEntries | read-only | mandatory | Parameter Type = Internal. The total number of available entries in the alarm log. This is based on the size of the alarm log. |
| 1.3.6.1.4.1.16.101.1.3.3.1.6 | ColumnalLogNotificationList | read-write | mandatory | Parameter Type = Immediate. Specifies root nodes that should receive alarm notifications for alarms in this log. These root nodes will send traps to EMS statio… |
| 1.3.6.1.4.1.16.101.1.3.3.1.7 | ColumnalLogClearEntries | write-only | mandatory | Parameter Type = Immediate. Set this field to the number of alarm entries you wish to clear from the top of the log. |
| 1.3.6.1.4.1.16.101.1.3.3.1.8 | ColumnalLogPartitionID | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.4.1.16.101.1.3.4 | TablealLogRecTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.3.4.1 | RowalLogRecEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.16.101.1.3.4.1.1 | ColumnalLogRecIndex | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.3.4.1.2 | ColumnalLogRecContents | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.4.1.16.101.1.3.5 | ScalaralTrapContents | not-accessible | mandatory | |
| 1.3.6.1.5.1 | NodescPartitionHeader | |||
| 1.3.6.1.5.1.1 | ScalarscPartitionControl | write-only | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.5.1.2 | ScalarscPartitionCRCCheck | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.5.1.3 | ScalarscPartitionFlushMode | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.5.2 | NodescSystemProfile | |||
| 1.3.6.1.5.2.1 | ScalarscSysNodeUpdate | read-only | mandatory | Parameter Type = Internal. This field will be set to loaded when the node is reset. |
| 1.3.6.1.5.2.2 | ScalarscSysNodeControl | write-only | mandatory | Parameter Type = Immediate. Validate database will set the database version number to the value used for this revision of ST software. Invalidate database will… |
| 1.3.6.1.5.2.3 | ScalarscSysNodeNumber | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.5.2.4 | ScalarscSysNodeDate | read-write | mandatory | Parameter Type = Immediate. This will update the NCP RTC clock. The format of the string is mm/dd/yyyy. |
| 1.3.6.1.5.2.5 | ScalarscSysNodeTime | read-write | mandatory | Parameter Type = Immediate. This will update the NCP RTC clock. The format of the string is hh:mm:ss. |
| 1.3.6.1.5.2.6 | ScalarscSysNodeType | read-write | mandatory | Parameter Type = Intrusive. A dedicated node is dedicated to a user or the CNMS. A root node is a dedicated node that serves as an active gateway to other ST n… |
| 1.3.6.1.5.2.7 | ScalarscSysNodePartitionID | read-write | mandatory | Parameter Type = Intrusive. 1 is reserved for CNMS. |
| 1.3.6.1.5.2.8 | ScalarscSysNodeMasterClockPriority | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.5.2.9 | ScalarscSysNodeMasterClockList | read-write | mandatory | Parameter Type = Immediate. Up to 16 master clock nodes, with two bytes used for each node number. |
| 1.3.6.1.5.2.10 | ScalarscSysNodeDatabaseVersion | read-only | mandatory | Parameter Type = Internal. Nonvolatile RAM database version number. If this number does not match the internal version number used for the revision of NCP code… |
| 1.3.6.1.5.2.11 | ScalarscSysNodeDefaultRoot | read-write | mandatory | Parameter Type = Immediate. Used by the trap generator to send traps if there is no alLogNotificationList specified. |
| 1.3.6.1.5.2.12 | ScalarscSysNodeCpiProfileUpdate | read-only | mandatory | Parameter Type = Internal. Indicates whether the CPI password control, the CPI session timeout time, the CPI maximum number of passthru sessions, or any of the… |
| 1.3.6.1.5.2.13 | ScalarscSysNodeCpiPasswordControl | read-write | mandatory | Parameter Type = Non-intrusive. Indicates whether CPI access is controlled using passwords or not. This field and the three CPI passwords apply to CPI access t… |
| 1.3.6.1.5.2.14 | ScalarscSysNodeCpiPasswordLevel1 | write-only | mandatory | Parameter Type = Non-intrusive. This password allows both read and write access to both local and remote nodes if password control is enabled. It applies to us… |
| 1.3.6.1.5.2.15 | ScalarscSysNodeCpiPasswordLevel2 | write-only | mandatory | Parameter Type = Non-intrusive. This password allows both read and write access to the local node and read-only access to remote nodes if password control is e… |
| 1.3.6.1.5.2.16 | ScalarscSysNodeCpiPasswordLevel3 | write-only | mandatory | Parameter Type = Non-intrusive. This password allows read-only access to both local and remote nodes if password control is enabled. It applies to users access… |
| 1.3.6.1.5.2.17 | ScalarscSysNodeCpiSessionTimeOut | read-write | mandatory | Parameter Type = Non-intrusive. CPI session will terminate when no request is made for number of minutes given by this value. For the CPI port, this time-out o… |
| 1.3.6.1.5.2.18 | ScalarscSysNodeCpiMaxPassthruSessions | read-write | mandatory | Parameter Type = Non-intrusive. This value indicates the maximum number of CPI access device passthru sessions that can be active simultaneously. |
| 1.3.6.1.5.3 | TablescRootAccessTable | not-accessible | mandatory | |
| 1.3.6.1.5.3.1 | RowscRootAccessEntry | not-accessible | mandatory | |
| 1.3.6.1.5.3.1.1 | ColumnscRootAccessIndex | read-only | mandatory | Parameter Type = Internal. Up to 16 EMS stations can access the node. |
| 1.3.6.1.5.3.1.2 | ColumnscRootAccessControlMode | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.5.3.1.3 | ColumnscRootAccessIp | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.5.4 | TablescNodeAccessTable | not-accessible | mandatory | |
| 1.3.6.1.5.4.1 | RowscNodeAccessEntry | not-accessible | mandatory | |
| 1.3.6.1.5.4.1.1 | ColumnscNodeAccessIndex | read-only | mandatory | Parameter Type = Internal. Maximum of 32 partitions per node. If the node is a dedicated CNMS node, only the entry for CNMS (partition ID 1) exists. The rest o… |
| 1.3.6.1.5.4.1.2 | ColumnscNodeAccessControlMode | read-write | mandatory | Parameter Type = Immediate. Full access will only check the requester's partition ID. Table access will use the root node list to verify the requester's partit… |
| 1.3.6.1.5.4.1.3 | ColumnscNodeAccessUpdate | read-only | mandatory | Parameter Type = Internal. Indicates whether current throughput value has been loaded. Load all throughput values using scSysNodeControl(updateThroughput). |
| 1.3.6.1.5.4.1.4 | ColumnscNodeAccessRootList | read-write | mandatory | Parameter Type = Immediate. A list of up to 16 root nodes (2 bytes per node number) within the partition that have access to this node. This list is only used … |
| 1.3.6.1.5.4.1.5 | ColumnscNodeAccessChPrfList | read-write | mandatory | Parameter Type = Immediate. A bit map representing which channel profiles (1-255) are assigned to this partition. The rightmost bit of the rightmost octet (lsb… |
| 1.3.6.1.5.4.1.6 | ColumnscNodeAccessThroughput | read-write | mandatory | Parameter Type = Intrusive. Access bandwidth for this partition, in units of bps. This field is only used on a shared node. |
| 1.3.6.1.5.4.1.7 | ColumnscNodeAccessVoicePrfList | read-write | mandatory | Parameter Type = Immediate. INTRODUCED 2.0.0 A bit map representing which voice profiles (1-255) are assigned to this partition. The rightmost bit of the right… |
| 1.3.6.1.5.4.1.8 | ColumnscNodeAccessLink2TraEntriesMin | read-write | mandatory | Parameter Type = Immediate. INTRODUCED 2.0.0 Defines the number of LINK translation table entries, that are reserved for this partition. The sum of the values … |
| 1.3.6.1.5.4.1.9 | ColumnscNodeAccessLink2TraEntriesMax | read-write | mandatory | Parameter Type = Immediate. INTRODUCED 2.0.0 Defines the limit of the number of LINK translation table entries that may be used by this partition. This number … |
| 1.3.6.1.5.5 | TablescCommunityTable | not-accessible | deprecated | |
| 1.3.6.1.5.5.1 | RowscCommunityEntry | not-accessible | deprecated | |
| 1.3.6.1.5.5.1.1 | ColumnscCommunityIndex | read-only | deprecated | Parameter Type = Internal. Format is partition ID (1-1023):entry ID (1-5). Only 32 partitions can be entered, each with 5 entries. |
| 1.3.6.1.5.5.1.2 | ColumnscCommunityControlMode | read-write | deprecated | Parameter Type = Immediate. A community entry cannot be erased if it is enabled. Community entry 1.1 cannot be disabled or erased. |
| 1.3.6.1.5.5.1.3 | ColumnscCommunityName | read-write | deprecated | Parameter Type = Immediate. |
| 1.3.6.1.5.5.1.4 | ColumnscCommunityscMap | read-write | deprecated | Parameter Type = Immediate. Represents which groups in the security MIB this community has access to. For each octet, 1 means no access, 2 means read-only, and… |
| 1.3.6.1.5.5.1.5 | ColumnscCommunityrecfMap | read-write | deprecated | Parameter Type = Immediate. Represents which groups in the resource configuration MIB this community has access to. For each octet, 1 means no access, 2 means … |
| 1.3.6.1.5.5.1.6 | ColumnscCommunityrestMap | read-write | deprecated | Parameter Type = Immediate. Represents which groups in the resource status MIB this community has access to. For each octet, 1 means no access, 2 means read-on… |
| 1.3.6.1.5.5.1.7 | ColumnscCommunityrestatisticsMap | read-write | deprecated | Parameter Type = Immediate. Represents which groups in the resource statistics MIB this community has access to. For each octet, 1 means no access, 2 means rea… |
| 1.3.6.1.5.5.1.8 | ColumnscCommunityalMap | read-write | deprecated | Parameter Type = Immediate. Represents which groups in the alarm MIB this community has access to. For each octet, 1 means no access, 2 means read-only, and 3 … |
| 1.3.6.1.5.6 | TablescTrapAccessTable | not-accessible | mandatory | |
| 1.3.6.1.5.6.1 | RowscTrapAccessEntry | not-accessible | mandatory | |
| 1.3.6.1.5.6.1.1 | ColumnscTrapAccessIndex | read-only | mandatory | Parameter Type = Internal. Indicates which of up to 8 EMS stations will receive traps. |
| 1.3.6.1.5.6.1.2 | ColumnscTrapAccessControlMode | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.5.6.1.3 | ColumnscTrapAccessIp | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.5.7 | TablescChProfileTable | not-accessible | mandatory | |
| 1.3.6.1.5.7.1 | RowscChProfileEntry | not-accessible | mandatory | |
| 1.3.6.1.5.7.1.1 | ColumnscChProfileIndex | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.5.7.1.2 | ColumnscChProfileControlMode | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.5.7.1.3 | ColumnscChProfileCostType | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.5.7.1.4 | ColumnscChProfileMaxCost | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.5.7.1.5 | ColumnscChProfilePriority | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.5.7.1.6 | ColumnscChProfileEncryption | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.5.7.1.7 | ColumnscChProfileMaxSatHop | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.5.7.1.8 | ColumnscChProfileErrPerformReq | read-write | mandatory | Parameter Type = Immediate. Error performance requirement (x) used as 10E-(x). Range 10E-4 to 10E-9. |
| 1.3.6.1.5.7.1.9 | ColumnscChProfileINLGroup | read-write | mandatory | Parameter Type = Immediate. 0 means do not care. |
| 1.3.6.1.5.7.1.10 | ColumnscChProfileOverrideMode | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.5.7.1.11 | ColumnscChProfileRetryTimer | read-write | mandatory | Parameter Type = Immediate. Each unit represents 5 seconds. Retry range is 5 seconds to 5 minutes. |
| 1.3.6.1.5.7.1.12 | ColumnscChProfileInfoAlarmGen | read-write | mandatory | Parameter Type = Immediate. Indicates whether channel alarms of severity info will be generated or not. |
| 1.3.6.1.5.8 | NodescSoftloadEntry | |||
| 1.3.6.1.5.8.1 | ScalarscSoftloadControl | write-only | mandatory | Parameter Type = Immediate. <startDownload> is the command to initiate download from EMS, local CPS, or another ST node to online FLASH memory location. <onlin… |
| 1.3.6.1.5.8.2 | ScalarscSoftloadFileName | read-write | mandatory | Parameter Type = Immediate. Specifies the file on EMS or CPS station to be downloaded into NCP program store. The type of code in the file is indicated by scSo… |
| 1.3.6.1.5.8.3 | ScalarscSoftloadDirectoryName | read-write | mandatory | Parameter Type = Immediate. Specifies the directory path where the file that is to be downloaded resides on the EMS or CPS station. |
| 1.3.6.1.5.8.4 | ScalarscSoftloadDestPort | read-write | mandatory | Parameter Type = Immediate. Destination module/port for downloading software. If module address, then format is nest:slot:0. If the address is 0:0:0, then the … |
| 1.3.6.1.5.8.5 | ScalarscSoftloadSoftwareType | read-write | mandatory | Parameter Type = Immediate. Identifies the module type for downloading software or database image. |
| 1.3.6.1.5.8.6 | ScalarscSoftloadEmsNodeID | read-write | mandatory | Parameter Type = Immediate. Root node ID for the source EMS or ST node. Only used if scSoftloadSourceEmsIp is not 1.0.0.0. |
| 1.3.6.1.5.8.7 | ScalarscSoftloadSourceEmsIp | read-write | mandatory | Parameter Type = Immediate. Indicates the download server. If the value is 1.0.0.0, then CPS is being used. If value is 2.0.0.0, then another ST node is being … |
| 1.3.6.1.5.8.8 | ScalarscSoftloadTimeout | read-write | mandatory | Parameter Type = Immediate. In units of seconds. |
| 1.3.6.1.5.9 | NodescCpiAccess | |||
| 1.3.6.1.5.9.1 | ScalarscCpiControl | write-only | mandatory | Parameter Type = Immediate. Log off will terminate a session that was enabled by entering a password. If password control is disabled, then the command will do… |
| 1.3.6.1.5.9.2 | ScalarscCpiControlUpdate | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.5.9.3 | ScalarscCpiSpeed | read-write | mandatory | Parameter Type = Intrusive. In units of bps. |
| 1.3.6.1.5.9.4 | ScalarscCpiDataBits | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.5.9.5 | ScalarscCpiParity | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.5.9.6 | ScalarscCpiStopBits | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.5.10 | NodescModemAccess | |||
| 1.3.6.1.5.10.1 | ScalarscModemControl | write-only | mandatory | Parameter Type = Immediate. Log off will terminate a session that was enabled by entering a password. If password control is disabled, then the command will do… |
| 1.3.6.1.5.10.2 | ScalarscModemControlUpdate | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.5.10.3 | ScalarscModemSpeed | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.5.10.4 | ScalarscModemDataBits | read-only | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.5.10.5 | ScalarscModemParity | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.5.10.6 | ScalarscModemStopBits | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.5.10.7 | ScalarscModemControlLead | read-write | mandatory | Parameter Type = Intrusive. This field is not currently used. |
| 1.3.6.1.5.11 | NodescIpAccess | |||
| 1.3.6.1.5.11.1 | NodescIpProfile | |||
| 1.3.6.1.5.11.1.1 | ScalarscIpControl | write-only | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.5.11.1.2 | ScalarscIpControlUpdate | read-only | mandatory | Parameter Type = Internal. Indicates changes to both the IP profile and the IP offline subnet table. |
| 1.3.6.1.5.11.1.3 | ScalarscIpWANIpAddress | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.5.11.1.4 | ScalarscIpSubNetworkMask | read-write | mandatory | Parameter Type = Intrusive. Network ID mask for ST-50 network. |
| 1.3.6.1.5.11.1.5 | ScalarscIpRootGatewayIp | read-write | mandatory | Parameter Type = Intrusive. Root node Ethernet port IP address. |
| 1.3.6.1.5.11.1.6 | ScalarscIpRootGatewayMask | read-write | mandatory | Parameter Type = Intrusive. Network mask for root node's Ethernet port. This is the mask for the user's IP network. |
| 1.3.6.1.5.11.1.7 | ScalarscIpRootGatewayEthernet | read-write | mandatory | Parameter Type = Intrusive. Specifies the Ethernet protocol of the user's IP network. |
| 1.3.6.1.5.11.1.8 | ScalarscIpDefaultExtGateway | read-write | mandatory | Parameter Type = Intrusive. Default gateway IP address used by the root node. |
| 1.3.6.1.5.11.1.9 | ScalarscIpSlipAddress | read-write | mandatory | Parameter Type = Intrusive. IP address of the SLIP interface on the modem port. |
| 1.3.6.1.5.11.1.10 | ScalarscIpSlipMask | read-write | mandatory | Parameter Type = Intrusive. IP mask of the SLIP interface on the modem port. |
| 1.3.6.1.5.11.2 | TablescIpOnlineSubnetTable | not-accessible | mandatory | |
| 1.3.6.1.5.11.2.1 | RowscIpOnlineSubnetEntry | not-accessible | mandatory | |
| 1.3.6.1.5.11.2.1.1 | ColumnscIpOnlineSubnetIndex | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.5.11.2.1.2 | ColumnscIpOnlineSubnetAddr | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.5.11.3 | TablescIpOfflineSubnetTable | not-accessible | mandatory | |
| 1.3.6.1.5.11.3.1 | RowscIpOfflineSubnetEntry | not-accessible | mandatory | |
| 1.3.6.1.5.11.3.1.1 | ColumnscIpOfflineSubnetIndex | read-only | mandatory | Parameter Type = Internal. |
| 1.3.6.1.5.11.3.1.2 | ColumnscIpOfflineSubnetControl | write-only | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.5.11.3.1.3 | ColumnscIpOfflineSubnetAddr | read-write | mandatory | Parameter Type = Intrusive. |
| 1.3.6.1.5.12 | TablescLgmStaticRouteTable | not-accessible | mandatory | |
| 1.3.6.1.5.12.1 | RowscLgmStaticRouteEntry | not-accessible | mandatory | |
| 1.3.6.1.5.12.1.1 | ColumnscLgmStaticRouteNode | read-only | mandatory | Parameter Type = Internal. Routing destination node number. |
| 1.3.6.1.5.12.1.2 | ColumnscLgmStaticRouteIndex | read-only | mandatory | Parameter Type = Internal. Specifies a route entry number in the routing table for given node. |
| 1.3.6.1.5.12.1.3 | ColumnscLgmStaticRouteStartMode | read-write | mandatory | Parameter Type = Immediate. Setting to off will prevent this table entry from being used on routing (invalidates it). Setting to erase will free the entry. |
| 1.3.6.1.5.12.1.4 | ColumnscLgmStaticRouteNextIafHop | read-write | mandatory | Parameter Type = Immediate. Specifies next hop along given route. The hops are presented in terms of Link-2 IAFs. It is, in fact, LGM port number (server type … |
| 1.3.6.1.5.12.1.5 | ColumnscLgmStaticRouteLink2GwyNode | read-write | mandatory | Parameter Type = Immediate. Specifies Link-2 gateway node (node which has a LGM module) to get access into Link-2 subnetwork. |
| 1.3.6.1.5.12.1.6 | ColumnscLgmStaticRoutePathDelay | read-write | mandatory | Parameter Type = Immediate. Defines the number of Link-2 nodes (non-ST-50 hops) to this node. No ST-50 INLs are counted. |
| 1.3.6.1.5.13 | NodescVoicePrf | |||
| 1.3.6.1.5.13.1 | TablescVoicePrfNetTable | not-accessible | mandatory | Voice profile entries in this table will serve as a network wide profile for multiple voice connections across the network. Even though it is not enforced by t… |
| 1.3.6.1.5.13.1.1 | RowscVoicePrfNetEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.5.13.1.1.1 | ColumnscVoicePrfNetIndex | read-only | mandatory | Parameter Type = Internal. Index of the voice profile entry. |
| 1.3.6.1.5.13.1.1.2 | ColumnscVoicePrfNetControlMode | read-write | mandatory | Parameter Type = Immediate. Disable will prevent this voice profile from being applied to the any new voice connections. Erase will remove this voice profile f… |
| 1.3.6.1.5.13.1.1.3 | ColumnscVoicePrfNetCompressMode | read-write | mandatory | Parameter Type = Immediate. Defines which compression algorithm to use for voice channels connected using this voice profile. |
| 1.3.6.1.5.13.1.1.4 | ColumnscVoicePrfNetSpeed | read-write | mandatory | Parameter Type = Immediate. The compressed channel data rate for any voice subrate connections using this voice profile. For channels using a CELP compression … |
| 1.3.6.1.5.13.1.1.5 | ColumnscVoicePrfNetDTMFRelay | read-write | mandatory | Parameter Type = Immediate. Controls the DTMF relay on any voice connections that use this voice profile. When enabled, DTMF signals are transferred through th… |
| 1.3.6.1.5.13.1.1.6 | ColumnscVoicePrfNetFaxRelay | read-write | mandatory | Parameter Type = Immediate. Controls the fax relay on any voice connections that use this voice profile. When enabled, fax operation will be supported over the… |
| 1.3.6.1.5.13.1.1.7 | ColumnscVoicePrfNetFaxNSFMode | read-write | mandatory | Parameter Type = Immediate. Controls the non-standard fax mode on any voice connections that use this voice profile. Not applicable in PCM and ADPCM mode. |
| 1.3.6.1.5.13.1.1.8 | ColumnscVoicePrfNetVocoderEnable | read-write | mandatory | Parameter Type = Immediate. Controls the vocoder mode on any voice connections that use this voice profile. Not applicable in PCM and ADPCM mode. |
| 1.3.6.1.5.13.1.1.9 | ColumnscVoicePrfNetDataMode | read-write | mandatory | Parameter Type = Immediate. Controls the 2100 Hz detection logic and data mode operation with the ATC vocoder on any voice connections that use this voice prof… |
| 1.3.6.1.5.13.1.1.10 | ColumnscVoicePrfNetSignalingType | read-write | mandatory | Parameter Type = Immediate. The type of signaling used by the T1M/E1M bundles that connect to voice ports using this voice profile. |
| 1.3.6.1.5.13.1.1.11 | ColumnscVoicePrfNetSigIdlePttrn | read-write | mandatory | Parameter Type = Immediate. Defines the idle signaling pattern on any ASM voice ports that use this voice profile. This pattern is delivered to receive signal … |
| 1.3.6.1.5.13.2 | TablescVoicePrfNodeTable | not-accessible | mandatory | Voice profile entries in this table will serve as a nodal part of profile for voice connections. It is intended for individual fine adjustment of the voice par… |
| 1.3.6.1.5.13.2.1 | RowscVoicePrfNodeEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.5.13.2.1.1 | ColumnscVoicePrfNodeIndex | read-only | mandatory | Parameter Type = Internal. Index of the voice profile entry. |
| 1.3.6.1.5.13.2.1.2 | ColumnscVoicePrfNodeRdnGrpId | read-write | mandatory | Parameter Type = Immediate. Specifies the redundancy group value of the server module that the voice port will be allocated on. |
| 1.3.6.1.5.13.2.1.3 | ColumnscVoicePrfNodeTxAudSrcMode | read-write | mandatory | Parameter Type = Immediate. Controls the transmit audio source on any voice connections that use this voice profile. Not applicable in PCM mode. |
| 1.3.6.1.5.13.2.1.4 | ColumnscVoicePrfNodeRxAudOutMode | read-write | mandatory | Parameter Type = Immediate. Controls the receive audio output on any voice connections that use this voice profile. Not applicable in PCM mode. |
| 1.3.6.1.5.13.2.1.5 | ColumnscVoicePrfNodeEchoCancel | read-write | mandatory | Parameter Type = Immediate. Controls the echo cancellation on any voice connections that use this voice profile. Not applicable in PCM and ADPCM mode. |
| 1.3.6.1.5.13.2.1.6 | ColumnscVoicePrfNodeNonLinear | read-write | mandatory | Parameter Type = Immediate. Controls the non-linear processing inside the echo canceller on any voice connections that use this voice profile. Not applicable i… |
| 1.3.6.1.5.13.2.1.7 | ColumnscVoicePrfNodeTxPCMGain | read-write | mandatory | Parameter Type = Immediate. Controls the transmit PCM gain on any voice connections that use this voice profile. Range is defined from -33.0 dB to +18.0 dB wit… |
| 1.3.6.1.5.13.2.1.8 | ColumnscVoicePrfNodeRxPCMGain | read-write | mandatory | Parameter Type = Immediate. Controls the receive PCM gain on any voice connections that use this voice profile. Range is defined from -33.0 dB to +18.0 dB with… |
| 1.3.6.1.5.13.2.1.9 | ColumnscVoicePrfNodePCMPhasorSize | read-write | mandatory | Parameter Type = Immediate. Size of the phasor (in bytes) on the PCM (64K) side of any voice connections using this voice profile. Not applicable in PCM mode. |
| 1.3.6.1.5.13.2.1.10 | ColumnscVoicePrfNodeSubratePhSize | read-write | mandatory | Parameter Type = Immediate. Size of the phasor (in bytes) on the subrate side of any voice connections using this voice profile. Not applicable in PCM mode. |
| 1.3.6.1.5.13.2.1.11 | ColumnscVoicePrfNodeNetSigMode | read-write | mandatory | Parameter Type = Immediate. Enable autodetection of CELP/ATC channel connected equipment so as to automatically change format to become compatible with either … |
| 1.3.6.1.5.14 | NodescCmntyAccess | |||
| 1.3.6.1.5.14.1 | TablescCmntyAccessTable | not-accessible | mandatory | Represents the common attributes of multiple community tables. |
| 1.3.6.1.5.14.1.1 | RowscCmntyAccessEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.5.14.1.1.1 | ColumnscCmntyAccessIndex | read-only | mandatory | Parameter Type = Internal. Format is: partition ID (1-1023):entry ID (1-5). Only 32 partitions can be entered, each with 5 entries. |
| 1.3.6.1.5.14.1.1.2 | ColumnscCmntyAccessControlMode | read-write | mandatory | Parameter Type = Immediate. A community entry cannot be erased if it is enabled. Community entry 1.1 cannot be disabled or erased. |
| 1.3.6.1.5.14.1.1.3 | ColumnscCmntyAccessCommunityName | read-write | mandatory | Parameter Type = Immediate. |
| 1.3.6.1.5.14.2 | TablescCmntyMib2Table | not-accessible | mandatory | Community profile table for MIB-II sections that are supported by ST. A community profile entry will define which sections of MIB-II a user has access to based… |
| 1.3.6.1.5.14.2.1 | RowscCmntyMib2Entry | not-accessible | mandatory | INTRODUCED 2.0.1 |
| 1.3.6.1.5.14.2.1.1 | ColumnscCmntyMib2Index | read-only | mandatory | Parameter Type = Internal. The first two bytes of this index are a partition ID with a range of 1 to 1023. There can be at most 32 partitions for a single node… |
| 1.3.6.1.5.14.2.1.2 | ColumnscCmntyMib2SystemAccess | read-write | mandatory | Parameter Type = Immediate. Defines access rights for a community entry to the MIB-II system group. |
| 1.3.6.1.5.14.2.1.3 | ColumnscCmntyMib2InterfacesAccess | read-write | mandatory | Parameter Type = Immediate. Defines access rights for a community entry to the MIB-II interfaces group. |
| 1.3.6.1.5.14.2.1.4 | ColumnscCmntyMib2AtAccess | read-write | mandatory | Parameter Type = Immediate. Defines access rights for a community entry to the MIB-II at group. |
| 1.3.6.1.5.14.2.1.5 | ColumnscCmntyMib2IpAccess | read-write | mandatory | Parameter Type = Immediate. Defines access rights for a community entry to the MIB-II ip group. |
| 1.3.6.1.5.14.2.1.6 | ColumnscCmntyMib2IcmpAccess | read-write | mandatory | Parameter Type = Immediate. Defines access rights for a community entry to the MIB-II icmp group. |
| 1.3.6.1.5.14.2.1.7 | ColumnscCmntyMib2UdpAccess | read-write | mandatory | Parameter Type = Immediate. Defines access rights for a community entry to the MIB-II udp group. |
| 1.3.6.1.5.14.2.1.8 | ColumnscCmntyMib2SnmpAccess | read-write | mandatory | Parameter Type = Immediate. Defines access rights for a community entry to the MIB-II snmp group. |
| 1.3.6.1.5.14.3 | TablescCmntySecTable | not-accessible | mandatory | Represents which groups in the security MIB this community has access to. |
| 1.3.6.1.5.14.3.1 | RowscCmntySecEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.5.14.3.1.1 | ColumnscCmntySecIndex | read-only | mandatory | Parameter Type = Internal. Format is: partition ID (1-1023):entry ID (1-5). Only 32 partitions can be entered, each with 5 entries. |
| 1.3.6.1.5.14.3.1.2 | ColumnscCmntySecPartHeaderAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to scPartitionHeader - the security MIB partition header. |
| 1.3.6.1.5.14.3.1.3 | ColumnscCmntySecSystemProfileAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to scSystemProfile - the security MIB system prof. section. |
| 1.3.6.1.5.14.3.1.4 | ColumnscCmntySecRootAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to scRootAccessTable - the security MIB root access section. |
| 1.3.6.1.5.14.3.1.5 | ColumnscCmntySecNodeAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to scNodeAccessTable - the security MIB node access section. |
| 1.3.6.1.5.14.3.1.6 | ColumnscCmntySecTrapAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to scTrapAccessTable - the security MIB trap access section. |
| 1.3.6.1.5.14.3.1.7 | ColumnscCmntySecChanProfileAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to scChProfileTable - the security MIB channel prof. section. |
| 1.3.6.1.5.14.3.1.8 | ColumnscCmntySecSoftloadAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to scSoftloadEntry - the security MIB softload section. |
| 1.3.6.1.5.14.3.1.9 | ColumnscCmntySecCPIAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to scCpiAccess - the security MIB CPI access section. |
| 1.3.6.1.5.14.3.1.10 | ColumnscCmntySecModemAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to scModemAccess - the security MIB modem access section. |
| 1.3.6.1.5.14.3.1.11 | ColumnscCmntySecIPAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to scIpAccess - the security MIB IP access section. |
| 1.3.6.1.5.14.3.1.12 | ColumnscCmntySecLGMRoutingAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to scLgmStaticRouteTable - the security MIB LGM static routing table section. |
| 1.3.6.1.5.14.3.1.13 | ColumnscCmntySecVoiceProfileAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to scVoicePrf - the security MIB voice profile section. |
| 1.3.6.1.5.14.3.1.14 | ColumnscCmntySecCommunityAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to scCmntyAccess - the security MIB community section. |
| 1.3.6.1.5.14.4 | TablescCmntyRecfTable | not-accessible | mandatory | Represents which groups in the resource configuration MIB this community has access to. |
| 1.3.6.1.5.14.4.1 | RowscCmntyRecfEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.5.14.4.1.1 | ColumnscCmntyRecfIndex | read-only | mandatory | Parameter Type = Internal. Format is: partition ID (1-1023):entry ID (1-5). Only 32 partitions can be entered, each with 5 entries. |
| 1.3.6.1.5.14.4.1.2 | ColumnscCmntyRecfPartHeader | read-write | mandatory | Parameter Type = Immediate. Specifies access to recfPartitionHeader - the resource MIB partition header section. |
| 1.3.6.1.5.14.4.1.3 | ColumnscCmntyRecfNodeAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to recfNode - the resource configuration MIB node section. |
| 1.3.6.1.5.14.4.1.4 | ColumnscCmntyRecfNestAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to recfNest - the resource configuration MIB nest section. |
| 1.3.6.1.5.14.4.1.5 | ColumnscCmntyRecfSlotAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to recfSlot - the resource configuration MIB slot section. |
| 1.3.6.1.5.14.4.1.6 | ColumnscCmntyRecfModuleAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to recfModule - the resource configuration MIB generic module section. |
| 1.3.6.1.5.14.4.1.7 | ColumnscCmntyRecfPortAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to recfPort - the resource configuration MIB generic port section. |
| 1.3.6.1.5.14.4.1.8 | ColumnscCmntyRecfBundleAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to recfBundle - the resource configuration MIB bundle section. |
| 1.3.6.1.5.14.4.1.9 | ColumnscCmntyRecfINLAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to recfINL - the resource configuration MIB INL section. |
| 1.3.6.1.5.14.4.1.10 | ColumnscCmntyRecfTDMChannelAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to recfTDMChannel - the resource configuration MIB TDM channel section. |
| 1.3.6.1.5.14.4.1.11 | ColumnscCmntyRecfFrRelayAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to recfFrame - the resource configuration MIB frame relay section. |
| 1.3.6.1.5.14.4.1.12 | ColumnscCmntyRecfAd10PortAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to recfAd10Port - the resource configuration MIB AD10 port section. |
| 1.3.6.1.5.14.4.1.13 | ColumnscCmntyRecfAsmPortAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to recfAsmPort - the resource configuration MIB ASM port section. |
| 1.3.6.1.5.14.4.1.14 | ColumnscCmntyRecfRtmPortAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to recfRtmPort - the resource configuration MIB RTM port section. |
| 1.3.6.1.5.14.4.1.15 | ColumnscCmntyRecfLgmPortAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to recfLgmPort - the resource configuration MIB LGM port section. |
| 1.3.6.1.5.14.4.1.16 | ColumnscCmntyRecfDsmPortAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to recfDsmPort - the resource configuration MIB DSM port section. |
| 1.3.6.1.5.14.4.1.17 | ColumnscCmntyRecfTranslationAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to recfTranslation - the resource configuration MIB translation section. |
| 1.3.6.1.5.14.4.1.18 | ColumnscCmntyRecfHwRscAccess | read-write | mandatory | Parameter Type = Immediate. INTRODUCED 2.0.1 Defines access rights for a community entry to the resource configuration hardware resource section (recfHwRsc). |
| 1.3.6.1.5.14.5 | TablescCmntyRestTable | not-accessible | mandatory | Represents which groups in the resource status MIB this community has access to. |
| 1.3.6.1.5.14.5.1 | RowscCmntyRestEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.5.14.5.1.1 | ColumnscCmntyRestIndex | read-only | mandatory | Parameter Type = Internal. Format is: partition ID (1-1023):entry ID (1-5). Only 32 partitions can be entered, each with 5 entries. |
| 1.3.6.1.5.14.5.1.2 | ColumnscCmntyRestNodeAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to restNode - the resource status MIB node section. |
| 1.3.6.1.5.14.5.1.3 | ColumnscCmntyRestNestAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to restNest - the resource status MIB nest section. |
| 1.3.6.1.5.14.5.1.4 | ColumnscCmntyRestSlotAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to restSlot - the resource status MIB slot section. |
| 1.3.6.1.5.14.5.1.5 | ColumnscCmntyRestModuleAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to restModule - the resource status MIB module section. |
| 1.3.6.1.5.14.5.1.6 | ColumnscCmntyRestPortAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to restPort - the resource status MIB port section. |
| 1.3.6.1.5.14.5.1.7 | ColumnscCmntyRestBundleAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to restBundle - the resource status MIB bundle section. |
| 1.3.6.1.5.14.5.1.8 | ColumnscCmntyRestINLAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to restINL - the resource status MIB INL section. |
| 1.3.6.1.5.14.5.1.9 | ColumnscCmntyRestINLContentsAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to restINLContentsTable - the resource status MIB INL contents section. |
| 1.3.6.1.5.14.5.1.10 | ColumnscCmntyRestChannelAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to restChannel - the resource status MIB channel section. |
| 1.3.6.1.5.14.5.1.11 | ColumnscCmntyRestAd10PortAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to restAd10Port - the resource status MIB AD10 port section. |
| 1.3.6.1.5.14.5.1.12 | ColumnscCmntyRestAsmPortAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to restAsmPort - the resource status MIB ASM port section. |
| 1.3.6.1.5.14.5.1.13 | ColumnscCmntyRestTrkGrpAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to restTrunkGroup - the resource status MIB trunk group section. |
| 1.3.6.1.5.14.5.1.14 | ColumnscCmntyRestRtmPortAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to restRtmPort - the resource status MIB RTM port section. |
| 1.3.6.1.5.14.5.1.15 | ColumnscCmntyRestLgmPortAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to restLgmPort - the resource status MIB LGM port section. |
| 1.3.6.1.5.14.5.1.16 | ColumnscCmntyRestSafAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to restSaf - the resource status MIB SAF section. |
| 1.3.6.1.5.14.5.1.17 | ColumnscCmntyRestDsmPortAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to restDsmPort - the resource status MIB DSM port section. |
| 1.3.6.1.5.14.5.1.18 | ColumnscCmntyRestHwRscAccess | read-write | mandatory | Parameter Type = Immediate. INTRODUCED 2.0.1 Defines access rights for a community entry to the resource status hardware resource section (restHwRsc). |
| 1.3.6.1.5.14.6 | TablescCmntyRestStTable | not-accessible | mandatory | Represents which groups in the resource statistics MIB this community has access to. |
| 1.3.6.1.5.14.6.1 | RowscCmntyRestStEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.5.14.6.1.1 | ColumnscCmntyRestStIndex | read-only | mandatory | Parameter Type = Internal. Format is: partition ID (1-1023):entry ID (1-5). Only 32 partitions can be entered, each with 5 entries. |
| 1.3.6.1.5.14.6.1.2 | ColumnscCmntyRestStModuleAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to restStatModule - the resource statistics MIB module section. |
| 1.3.6.1.5.14.6.1.3 | ColumnscCmntyRestStPortAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to restStatPort - the resource statistics MIB port section. |
| 1.3.6.1.5.14.6.1.4 | ColumnscCmntyRestStINLAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to restStatInl - the resource statistics MIB INL section. |
| 1.3.6.1.5.14.6.1.5 | ColumnscCmntyRestStChannelAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to restStatCh - the resource statistics MIB channel section. |
| 1.3.6.1.5.14.6.1.6 | ColumnscCmntyRestStAd10Access | read-write | mandatory | Parameter Type = Immediate. Specifies access to restStatAd10 - the resource statistics MIB AD-10 section. |
| 1.3.6.1.5.14.7 | TablescCmntyAlmTable | not-accessible | mandatory | Represents which groups in the alarm MIB this community has access to. |
| 1.3.6.1.5.14.7.1 | RowscCmntyAlmEntry | not-accessible | mandatory | INTRODUCED 2.0.0 |
| 1.3.6.1.5.14.7.1.1 | ColumnscCmntyAlmIndex | read-only | mandatory | Parameter Type = Internal. Format is: partition ID (1-1023):entry ID (1-5). Only 32 partitions can be entered, each with 5 entries. |
| 1.3.6.1.5.14.7.1.2 | ColumnscCmntyAlmPartHeader | read-write | mandatory | Parameter Type = Immediate. Specifies access to alPartitionHeader - the alarm MIB partition header section. |
| 1.3.6.1.5.14.7.1.3 | ColumnscCmntyAlmAlarmProfileAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to alSystemProfile - the alarm MIB alarm profile section. |
| 1.3.6.1.5.14.7.1.4 | ColumnscCmntyAlmAlarmLogAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to alLog - the alarm MIB alarm log section. |
| 1.3.6.1.5.14.7.1.5 | ColumnscCmntyAlmAlarmRecordAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to alLogRecord - the alarm MIB alarm record section. |
| 1.3.6.1.5.14.7.1.6 | ColumnscCmntyAlmTrapAccess | read-write | mandatory | Parameter Type = Immediate. Specifies access to alTrapContents - the alarm MIB trap section. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| Ad10PortAddr | OCTET STRING (SIZE (6)) | ||
| AlarmRecord | OCTET STRING (SIZE (64)) | ||
| AsmX50CkAddr | OCTET STRING (SIZE (6)) | ||
| BundleAddr | OCTET STRING (SIZE (6)) | ||
| ChannelAddr | OCTET STRING (SIZE (6)) | ||
| ChannelStatusAddr | OCTET STRING (SIZE (9)) | ||
| Link2Addr | OCTET STRING (SIZE (8)) | ||
| Link2Index | OCTET STRING (SIZE (4)) | ||
| NestAddr | OCTET STRING (SIZE (1)) | ||
| NodeAddr | OCTET STRING (SIZE (2)) | ||
| PortAddr | OCTET STRING (SIZE (4)) | ||
| RecordIndex | OCTET STRING (SIZE (4)) | ||
| RtmAdPortAddr | OCTET STRING (SIZE (6)) | ||
| SlotAddr | OCTET STRING (SIZE (2)) |