SWITCH_MIB
417 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC-1215 | TRAP-TYPE |
| RFC1155-SMI | Counter Gauge IpAddress mgmt NetworkAddress TimeTicks |
| RFC1213-MIB | DisplayString |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.17.1 | NodenewRoot | Become the new root of the Spanning Tree. | ||
| 1.3.6.1.2.1.17.2 | NodetopologyChange | Spanning tree topology change. | ||
| 1.3.6.1.4 | Nodeprivate | |||
| 1.3.6.1.4.1 | Nodeenterprises | |||
| 1.3.6.1.4.1.867 | Nodekti | |||
| 1.3.6.1.4.1.867.100 | Nodeswitch | |||
| 1.3.6.1.4.1.867.100.1 | NodebasicSwitchMgt | |||
| 1.3.6.1.4.1.867.100.1.2 | ScalarswitchSoftwareVersion | read-only | mandatory | The current software/firmware version implemented in this device represented in non-zero integer. e.g. 10000 means version 1.00.00 |
| 1.3.6.1.4.1.867.100.1.3 | ScalarswitchHwAgingSwitch | read-write | mandatory | Enable the HW aging or not. |
| 1.3.6.1.4.1.867.100.1.4 | ScalarswitchAgingTime | read-write | mandatory | The timeout period in seconds for aging out dynamically learned forwarding information. 802.1D-1990 recommends a default of 300 seconds. the unit is 1 sec. |
| 1.3.6.1.4.1.867.100.1.5 | ScalarswitchRestartControl | read-write | current | Setting this object to warmBoot(2) causes the device to restart the application software with current configuration parameters saved in non-volatile memory. Se… |
| 1.3.6.1.4.1.867.100.1.6 | ScalarswitchPortNumber | read-only | current | The total port number of this switch. |
| 1.3.6.1.4.1.867.100.1.9 | ScalarswitchAutoMode | read-write | mandatory | AutoDetect(1)/AutoNegotiation(2) of the Auto Mode in this switch. |
| 1.3.6.1.4.1.867.100.1.10 | ScalarswitchVlanMode | read-write | mandatory | IVL(1)/SVL(2) of the VLAN Mode in this switch. |
| 1.3.6.1.4.1.867.100.2 | NodebasicPortMgt | |||
| 1.3.6.1.4.1.867.100.2.1 | TableportTable | not-accessible | mandatory | Basic information for each port. |
| 1.3.6.1.4.1.867.100.2.1.1 | RowportEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.2.1.1.1 | ColumnportIndex | read-only | mandatory | port number, This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.867.100.2.1.1.2 | ColumnportName | read-write | mandatory | Name of each port. |
| 1.3.6.1.4.1.867.100.2.1.1.3 | ColumnportType | read-only | mandatory | The type of each port. |
| 1.3.6.1.4.1.867.100.2.1.1.4 | ColumnportLink | read-only | mandatory | This object indicates the link status of each port is up or down. |
| 1.3.6.1.4.1.867.100.2.1.1.5 | ColumnportAdminEnable | read-write | mandatory | Enable/disable status of the port |
| 1.3.6.1.4.1.867.100.2.1.1.6 | ColumnportAutoNegotiation | read-write | mandatory | Enable(1)/disable(2) status of auto negotiation |
| 1.3.6.1.4.1.867.100.2.1.1.7 | ColumnportCapabilities | read-only | current | Port capabilities. { portCap10half(0), portCap10full(1), portCap100half(2), portCap100full(3), portCap1000half(4), portCap1000full(5), reserved6(6), reserved7(… |
| 1.3.6.1.4.1.867.100.2.1.1.8 | ColumnportPartnerCapability | read-only | current | Port PartnerCapability. { portCap10half(0), portCap10full(1), portCap100half(2), portCap100full(3), portCap1000half(4), portCap1000full(5), reserved6(6), reser… |
| 1.3.6.1.4.1.867.100.2.1.1.9 | ColumnportSpeedDpxStatus | read-write | mandatory | The operating speed and duplex mode of the switched port. |
| 1.3.6.1.4.1.867.100.2.1.1.10 | ColumnportFlowControlConfiguration | read-write | mandatory | Flow control configuration, |
| 1.3.6.1.4.1.867.100.2.2 | TablenetConfigTable | not-accessible | mandatory | This table contains addressing information relevant to this interface corresponding to IfEntry table. The number of entries is given by the value of ifNumber. |
| 1.3.6.1.4.1.867.100.2.2.1 | RownetConfigEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.2.2.1.1 | ColumnnetConfigIndex | read-only | mandatory | This index value uniquely identifies the interface to which this entry is applicable. This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.867.100.2.2.1.2 | ColumnnetConfigOperation | read-only | mandatory | This object indicates the operational status of this device. |
| 1.3.6.1.4.1.867.100.2.2.1.3 | ColumnnetConfigMacAddr | read-only | mandatory | The MAC address of the specified interface of the device. |
| 1.3.6.1.4.1.867.100.2.2.1.4 | ColumnnetConfigIpAddr | read-write | mandatory | The Internet address of the specified interface of the device. |
| 1.3.6.1.4.1.867.100.2.2.1.5 | ColumnnetConfigSNetMask | read-write | mandatory | The internet address subnet mask of the specified interface of the device. |
| 1.3.6.1.4.1.867.100.2.2.1.6 | ColumnnetConfigDfGateway | read-write | mandatory | The default gateway address which the routed packets are delivered to. |
| 1.3.6.1.4.1.867.100.2.3 | TableprotectedTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.2.3.1 | RowprotectedEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.2.3.1.1 | Columnprotectedenable | read-write | mandatory | A switch to select whether the protected Port is Enable(1) or Disable(2). |
| 1.3.6.1.4.1.867.100.2.4 | TableprotectedPortTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.2.4.1 | RowprotectedPortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.2.4.1.1 | Columnprotectedindex | read-only | mandatory | |
| 1.3.6.1.4.1.867.100.2.4.1.2 | ColumnprotectedPortenable | read-write | mandatory | A switch to select whether the protected Port of Port is Enable(1) or Disable(2). |
| 1.3.6.1.4.1.867.100.3 | NodetrapMgt | |||
| 1.3.6.1.4.1.867.100.3.1 | NodeswitchTrapLevel | |||
| 1.3.6.1.4.1.867.100.3.1 | TableswitchTrapManagerTable | not-accessible | mandatory | This table contains the information needed for sending traps. |
| 1.3.6.1.4.1.867.100.3.1.1 | RowswitchTrapManagerEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.3.1.1.1 | ColumnswitchTrapManagerIndex | read-only | mandatory | |
| 1.3.6.1.4.1.867.100.3.1.1.2 | ColumnswitchTrapManagerIpAddr | read-write | mandatory | The Internet address of the management station which trap is sent to . |
| 1.3.6.1.4.1.867.100.3.1.1.3 | ColumnswitchTrapManagerComm | read-write | mandatory | Community name used for sending the trap to this management station |
| 1.3.6.1.4.1.867.100.3.1.1.4 | ColumnswitchTrapState | read-write | mandatory | |
| 1.3.6.1.4.1.867.100.4 | NodeaddrMgt | |||
| 1.3.6.1.4.1.867.100.4.2 | NodeaddrStaticMgt | |||
| 1.3.6.1.4.1.867.100.4.2.1 | ScalaraddrStaticMaxEntryNumber | read-only | mandatory | The max. count of static address table |
| 1.3.6.1.4.1.867.100.4.2.3 | ScalaraddrStaticUsedEntryNumber | read-only | mandatory | The used count of address entry. |
| 1.3.6.1.4.1.867.100.4.2.4 | ScalaraddrStaticMessageStatus | read-only | mandatory | The last status of static operation: (1) ok (2) address_found : set the same address (3) bad_value : address set error because of address is broadcast address … |
| 1.3.6.1.4.1.867.100.4.2.5 | TableaddrStaticTable | not-accessible | mandatory | The table contain information about static entry in the device. |
| 1.3.6.1.4.1.867.100.4.2.5.1 | RowaddrStaticEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.4.2.5.1.1 | ColumnaddrStaticIndex | read-only | mandatory | This index value uniquely identifies the address in static table. Value range between 1 and the value of addrStaticMaxAddrNumber. |
| 1.3.6.1.4.1.867.100.4.2.5.1.2 | ColumnaddrStaticSetAddress | read-write | mandatory | To set/modify the [static address] [Destination] [Port vid]. [6 bytes]/[4 bytes (portlist)][2 bytes]. If 802.1Q Virtual LAN is disable,vid is always 1. |
| 1.3.6.1.4.1.867.100.4.3 | TableaddrdynamicTable | not-accessible | mandatory | The table contain information about dynamic entry in the device. |
| 1.3.6.1.4.1.867.100.4.3.1 | RowaddrdynamicEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.4.3.1.1 | ColumnaddrdynamicIndex | read-only | mandatory | This index value uniquely identifies the address in dynamic table. |
| 1.3.6.1.4.1.867.100.4.3.1.2 | ColumnaddrdynamicAddress | read-only | mandatory | Display the [dynamic address] [port] [vid]. [6 bytes]/[1 bytes (portnumber)][2 bytes]. |
| 1.3.6.1.4.1.867.100.5 | NodestatisticMgt | |||
| 1.3.6.1.4.1.867.100.5.1 | ScalarresetMIBCounter | read-write | mandatory | Clear all MIB counters for all ports to zero |
| 1.3.6.1.4.1.867.100.5.2 | TablestatisticPortTable | not-accessible | mandatory | A table that contains information about every port that is associated with this transparent bridge. |
| 1.3.6.1.4.1.867.100.5.2.1 | RowstatisticPortEntry | not-accessible | mandatory | A list of information for each port of a transparent bridge. |
| 1.3.6.1.4.1.867.100.5.2.1.1 | ColumnstatisticPort | read-only | mandatory | This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.867.100.5.2.1.2 | ColumnstatisticPortReceiveGoodUnicastFrameCount | read-only | mandatory | The counter of Good Unicast Frame packets received by a port |
| 1.3.6.1.4.1.867.100.5.2.1.3 | ColumnstatisticPortReceiveGoodBroadcastFrameCount | read-only | mandatory | The counter of Good Broadcast Frame packets received by a port |
| 1.3.6.1.4.1.867.100.5.2.1.4 | ColumnstatisticPortReceiveGoodMulticastFrameCount | read-only | mandatory | The counter of Good Multicast Frame packets received by a port |
| 1.3.6.1.4.1.867.100.5.2.1.5 | ColumnstatisticPortReceive8023XMACControl | read-only | mandatory | The counter of 802.3XMACControl Frame packets received by a port |
| 1.3.6.1.4.1.867.100.5.2.1.6 | ColumnstatisticPortReceiveCRCError | read-only | mandatory | The counter of CRCErrors packets received by a port |
| 1.3.6.1.4.1.867.100.5.2.1.7 | ColumnstatisticPortReceiveFragment | read-only | mandatory | The counter of Fragment packets received by a port |
| 1.3.6.1.4.1.867.100.5.2.1.8 | ColumnstatisticPortReceiveJabbers | read-only | mandatory | The counter of Jabbers packets received by a port |
| 1.3.6.1.4.1.867.100.5.2.1.9 | ColumnstatisticPortReceiveTotalByteCountCount | read-only | mandatory | The counter of Total Byte Count received by a port |
| 1.3.6.1.4.1.867.100.5.2.1.10 | ColumnstatisticPortTransmitGoodUnicastFrameCount | read-only | mandatory | The counter of Good Unicast Frame Transmit by a port |
| 1.3.6.1.4.1.867.100.5.2.1.11 | ColumnstatisticPortTransmitGoodBroadcastFrameCount | read-only | mandatory | The counter of Good Broadcast Frame Transmit by a port |
| 1.3.6.1.4.1.867.100.5.2.1.12 | ColumnstatisticPortTransmitGoodMulticastFrameCount | read-only | mandatory | The counter of Good Multicast Frame Transmit by a port |
| 1.3.6.1.4.1.867.100.5.2.1.13 | ColumnstatisticPortTransmit8023XMACControl | read-only | mandatory | The counter of 802.3XMACControl Frame Transmit by a port |
| 1.3.6.1.4.1.867.100.5.2.1.14 | ColumnstatisticPortTotalTransmitByteCount | read-only | mandatory | The counter of Total Byte Count Transmit by a port |
| 1.3.6.1.4.1.867.100.6 | NodeportMirrorMgt | |||
| 1.3.6.1.4.1.867.100.6.1 | ScalarportMirrorSwitch | read-write | mandatory | A state to present whether the port monitor function is ON or OF in the device. The default is OFF. |
| 1.3.6.1.4.1.867.100.6.2 | ScalarmirrorCapturePort | read-write | mandatory | Destination port for mirrored packets. This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.867.100.6.3 | ScalarmirrorIngressPort | read-write | mandatory | Source ports for mirrored ingress packets. |
| 1.3.6.1.4.1.867.100.6.4 | ScalarmirrorIngressFiterRule | read-write | mandatory | all(1): Mirror all ingress frames DA(2): Mirror all received frame with DA=mirrorIngressMAC SA(2): Mirror all received frame with SA=mirrorIngressMAC |
| 1.3.6.1.4.1.867.100.6.6 | ScalarmirrorIngressDividerCount | read-write | mandatory | Mirror every n received frame (n= mirrorIngressDividerCount) |
| 1.3.6.1.4.1.867.100.6.7 | ScalarmirrorIngressMAC | read-write | mandatory | MAC address that will be compared against ingress frame in accordance with mirrorIngressFiterRule |
| 1.3.6.1.4.1.867.100.6.8 | ScalarmirrorEgressPort | read-write | mandatory | Source ports for mirrored Egress packets. |
| 1.3.6.1.4.1.867.100.6.9 | ScalarmirrorEgressFiterRule | read-write | mandatory | all(1): Mirror all Egress frames DA(2): Mirror all transmitted frame with DA=mirrorEgressMAC SA(2): Mirror all Transmitted frame with SA=mirrorEgressMAC |
| 1.3.6.1.4.1.867.100.6.11 | ScalarmirrorEgressDividerCount | read-write | mandatory | Mirror every n transmitted frame (n= mirrorEgressDividerCount) |
| 1.3.6.1.4.1.867.100.6.12 | ScalarmirrorEgressMAC | read-write | mandatory | MAC address that will be compared against egress frame in accordance with mirrorEgressFiterRule |
| 1.3.6.1.4.1.867.100.7 | NodevirtualLanMgt | |||
| 1.3.6.1.4.1.867.100.7.1 | ScalarvirtualLanSwitch | read-write | mandatory | A state to present whether the virtul LAN function is ON or OFF in the device. 1q_enable(1),portbased_enable(2) ,metro_enable(3),disable(4). The default value … |
| 1.3.6.1.4.1.867.100.7.2 | ScalarvirtualLanMaxDomainCount | read-only | mandatory | Max. Virtual LAN domain count in this device |
| 1.3.6.1.4.1.867.100.7.5 | TablevirtualLanPortBasedTable | not-accessible | mandatory | The table contain information for Virtual LAN function. |
| 1.3.6.1.4.1.867.100.7.5.1 | RowvirtualLanPortBasedEntry | not-accessible | mandatory | Table entry of port monitor. |
| 1.3.6.1.4.1.867.100.7.5.1.1 | ColumnvirtualLanNameIndex | read-only | mandatory | VLAN ID, the value range between 1 and the value of virtualLanMaxDomainCount |
| 1.3.6.1.4.1.867.100.7.5.1.2 | ColumnvirtualLanName | read-write | mandatory | Domain name |
| 1.3.6.1.4.1.867.100.7.5.1.3 | ColumnvirtualLanPortGet | read-only | mandatory | Get the ports to belong the given VLAN |
| 1.3.6.1.4.1.867.100.7.5.1.5 | ColumnvirtualLanPortAdd | read-write | mandatory | Add ports to the given VLAN |
| 1.3.6.1.4.1.867.100.7.5.1.6 | ColumnvirtualLanPortRemove | read-write | mandatory | Remove the given ports from the given VLAN |
| 1.3.6.1.4.1.867.100.7.6 | TablevirtualLanPortTable | not-accessible | mandatory | Table for port configuration in VLAN. |
| 1.3.6.1.4.1.867.100.7.6.1 | RowvirtualLanPortEntry | not-accessible | mandatory | Table for port configuration in VLAN. |
| 1.3.6.1.4.1.867.100.7.6.1.1 | ColumnvirtualLanPortIndex | read-only | mandatory | This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.867.100.7.6.1.3 | ColumnvLanPortPrivatevLantype | read-write | mandatory | The port type defined for Private vlan. |
| 1.3.6.1.4.1.867.100.7.6.1.4 | ColumnvLanPortStackRule | read-write | mandatory | It sets rule of port in VLAN Stacking. |
| 1.3.6.1.4.1.867.100.8 | NodetrunkMgt | |||
| 1.3.6.1.4.1.867.100.8.1 | ScalarportTrunkSwitch | read-write | mandatory | A switch to select whether the power link is ON or OFF. The default is OFF. |
| 1.3.6.1.4.1.867.100.8.2 | ScalarportTrunkMaxGroupCount | read-only | mandatory | Max. Trunk group count in this device |
| 1.3.6.1.4.1.867.100.8.3 | ScalarportTrunkMaxPortCount | read-only | mandatory | Max. Trunk port in a group in this device |
| 1.3.6.1.4.1.867.100.8.4 | ScalarlacpSystemPriority | read-write | mandatory | lacp Port Configuration,A switch to select whether the System Priority. |
| 1.3.6.1.4.1.867.100.8.5 | TableportTrunkGroupTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.8.5.1 | RowportTrunkGroupEntry | not-accessible | mandatory | Table entry of port Trunk. |
| 1.3.6.1.4.1.867.100.8.5.1.1 | ColumntrunkIndex | read-only | mandatory | The port index of Trunking Group Configuration. |
| 1.3.6.1.4.1.867.100.8.5.1.2 | Columntrunkportselectd | read-write | mandatory | A port belong to which is group . |
| 1.3.6.1.4.1.867.100.8.6 | TablelacpPortTable | not-accessible | mandatory | The table contain information for Port lacp function. |
| 1.3.6.1.4.1.867.100.8.6.1 | RowlacpPortEntry | not-accessible | mandatory | Table entry of port lacp. |
| 1.3.6.1.4.1.867.100.8.6.1.1 | ColumnlacpPortIndex | read-only | mandatory | lacp port index |
| 1.3.6.1.4.1.867.100.8.6.1.2 | ColumnlacpEnablePort | read-write | mandatory | lacp Port Configuration,it select portenable witch is enable or disable. |
| 1.3.6.1.4.1.867.100.9 | NodespanningTreeMgt | |||
| 1.3.6.1.4.1.867.100.9.1 | TablespanningTreeConfTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.9.1.1 | RowspanningTreeConfEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.9.1.1.1 | ColumnspanningTreeSwitch | read-write | mandatory | A switch to select whether the spanning tree is ON or OFF. The default is OFF. If the value is changed, the system will be restarted. |
| 1.3.6.1.4.1.867.100.9.1.1.2 | ColumnspanningTreeForceVersion | read-write | mandatory | A switch to select whether the Force Version is Normal or Compatible with old STP. The default is Normal. If the value is changed, the system will be restarted. |
| 1.3.6.1.4.1.867.100.9.1.1.3 | ColumnspanningTreeBridgePriority | read-write | mandatory | A switch to select whether the Bridge Priority. The default is 32768. The value must be in steps of 4096 . |
| 1.3.6.1.4.1.867.100.10 | NodepriorityMgt | |||
| 1.3.6.1.4.1.867.100.10.1 | ScalarprioritySwitch | read-write | mandatory | A switch to select whether the priority is enable/disable |
| 1.3.6.1.4.1.867.100.10.2 | ScalarpriorityMode | read-write | mandatory | A switch to select whether the priority Mode is Strict/Wrr |
| 1.3.6.1.4.1.867.100.10.3 | TableqosConfTable | not-accessible | mandatory | A Switch set up QoS information for each port. |
| 1.3.6.1.4.1.867.100.10.3.1 | RowqosConfEntry | not-accessible | mandatory | Port priority information entry. |
| 1.3.6.1.4.1.867.100.10.3.1.1 | ColumnportPriorityIndex | read-only | mandatory | port number, This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.867.100.10.3.1.2 | ColumnportPriorityPortSetting | read-write | mandatory | This is PortPriority,0(LOW),1(Normal),2(Medium),3(High) |
| 1.3.6.1.4.1.867.100.10.3.1.3 | ColumnportPriority8021pSetting | read-write | mandatory | 802.1p priority setting. |
| 1.3.6.1.4.1.867.100.10.3.1.4 | ColumnportPriorityDSCPSetting | read-write | mandatory | DSCP priority setting. |
| 1.3.6.1.4.1.867.100.10.4 | Tablepriority8021pmapTable | not-accessible | mandatory | A Switch set up QoS Map for the switch. |
| 1.3.6.1.4.1.867.100.10.4.1 | Rowpriority8021pmapEntry | not-accessible | mandatory | Priority information entry. |
| 1.3.6.1.4.1.867.100.10.4.1.1 | Columnmap8021ptagIndex | read-only | mandatory | This is the index of Priority tag value |
| 1.3.6.1.4.1.867.100.10.4.1.2 | Columnmap8021ptagvalue | read-only | mandatory | This is Priority tag 0-7 |
| 1.3.6.1.4.1.867.100.10.4.1.3 | Columnmap8021ptagpriority | read-write | mandatory | This is to assign priority queue of tag value,00(LOW),01(Normal),02(Medium),03(High) |
| 1.3.6.1.4.1.867.100.10.5 | TablepriorityDSCPmapTable | not-accessible | mandatory | A Switch set up QoS Map for the switch. |
| 1.3.6.1.4.1.867.100.10.5.1 | RowpriorityDSCPmapEntry | not-accessible | mandatory | Priority information entry. |
| 1.3.6.1.4.1.867.100.10.5.1.1 | ColumnmapDSCPIndex | read-only | mandatory | This is the index DSCP value , index=8 for all others |
| 1.3.6.1.4.1.867.100.10.5.1.2 | ColumnmapDSCPValue | read-write | mandatory | This is DSCP value |
| 1.3.6.1.4.1.867.100.10.5.1.3 | ColumnmapDSCPpriority | read-write | mandatory | This is to assign priority queue of DSCP value,00(LOW),01(Normal),02(Medium),03(High) |
| 1.3.6.1.4.1.867.100.11 | NodeigmpMgt | |||
| 1.3.6.1.4.1.867.100.11.2 | TableigmpPortTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.11.2.1 | RowigmpPortEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.11.2.1.1 | ColumnigmpPortGroupIndex | read-only | mandatory | |
| 1.3.6.1.4.1.867.100.11.2.1.2 | ColumnigmpRouterPortno | read-write | mandatory | A switch to select whether the Router Port. |
| 1.3.6.1.4.1.867.100.11.2.1.3 | ColumnigmpLeavePortMode | read-write | mandatory | To set leave mode of port. Leave mode: normal(1)/immediate(2)/fast(3). |
| 1.3.6.1.4.1.867.100.11.2.1.4 | ColumnigmpGroupLimitedMaximumGroupNumber | read-write | mandatory | The maximum group number of port. Range: 0~255. |
| 1.3.6.1.4.1.867.100.11.2.1.5 | ColumnigmpFilteringPortProfileEntryName | read-write | mandatory | The profile of port. |
| 1.3.6.1.4.1.867.100.11.3 | TablemultiPortGroupTable | not-accessible | mandatory | The information for the multicast group which stored in the multi-port table |
| 1.3.6.1.4.1.867.100.11.3.1 | RowmultiPortGroupEntry | not-accessible | mandatory | multi-port information entry. |
| 1.3.6.1.4.1.867.100.11.3.1.1 | ColumnmultiPortGroupIndex | read-only | mandatory | |
| 1.3.6.1.4.1.867.100.11.3.1.2 | ColumnmultiPortGroupVid | read-only | mandatory | |
| 1.3.6.1.4.1.867.100.11.3.1.3 | ColumnmultiPortGroupMACAddress | read-only | mandatory | |
| 1.3.6.1.4.1.867.100.11.3.1.4 | ColumnmultiPortGroupMember | read-only | mandatory | The port number belong to the multicast group |
| 1.3.6.1.4.1.867.100.11.6 | TableigmpFilteringProfileTable | not-accessible | mandatory | Profile Setup. |
| 1.3.6.1.4.1.867.100.11.6.1 | RowigmpFilteringProfileEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.11.6.1.1 | ColumnigmpFilteringProfileindex | read-only | mandatory | |
| 1.3.6.1.4.1.867.100.11.6.1.2 | ColumnigmpFilteringProfileShowProfileEntry | read-only | mandatory | To show profile entry. Format:profileEntryName |
| 1.3.6.1.4.1.867.100.11.7 | TableigmpFilteringRuleTable | not-accessible | mandatory | Rule Setup. |
| 1.3.6.1.4.1.867.100.11.7.1 | RowigmpFilteringRuleEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.11.7.1.1 | ColumnigmpFilteringRuleindex | read-only | mandatory | |
| 1.3.6.1.4.1.867.100.11.7.1.2 | ColumnigmpFilteringRuleShowRuleEntry | read-only | mandatory | To show rule entry. Format:profileEntryName,startAddress,endAddress |
| 1.3.6.1.4.1.867.100.11.201 | ScalarigmpSwitch | read-write | mandatory | A switch to select whether the igmp snooping is enable/disable Port Mirroring should be disable when set igmp enable. |
| 1.3.6.1.4.1.867.100.11.202 | ScalarigmpQuerying | read-write | mandatory | A switch to select whether the igmp igmp Querying. |
| 1.3.6.1.4.1.867.100.11.203 | ScalarigmpUnregisteredIPMCFlooding | read-write | mandatory | A switch to select whether the igmp Unregistered IPMC Flooding. |
| 1.3.6.1.4.1.867.100.11.204 | ScalarigmpQueryInterval | read-write | mandatory | A switch to select whether the igmp Query Interval(60-125). |
| 1.3.6.1.4.1.867.100.11.205 | ScalarigmpReportDelay | read-write | mandatory | A switch to select whether the igmp Report Delay(5-25). |
| 1.3.6.1.4.1.867.100.11.206 | ScalarigmpQueryTimeout | read-write | mandatory | A switch to select whether the igmp Query Timeout(255-500). |
| 1.3.6.1.4.1.867.100.11.207 | ScalarigmpFilteringEnabled | read-write | mandatory | A state to present whether the igmp filtering function is ON or OFF in the device. The default value is OFF. |
| 1.3.6.1.4.1.867.100.11.208 | ScalarigmpGroupLimitedPortEnabled_map | read-create | current | A switch to enable/disable group limited of ports. |
| 1.3.6.1.4.1.867.100.11.211 | ScalarigmpFilteringProfileAddEntry | read-write | mandatory | To add entry. Format:profileEntryName,startAddress,endAddress Example:abc,225.0.0.0,238.0.0.1 NOTE:Please don't use space or ',' for profile naming. |
| 1.3.6.1.4.1.867.100.11.212 | ScalarigmpFilteringProfileDeleteProfileEntry | read-write | mandatory | To delete profile entry. Format:profileEntryName Example:abc |
| 1.3.6.1.4.1.867.100.11.213 | ScalarigmpFilteringProfileDeleteRuleEntry | read-write | mandatory | To delete rule entry. Format:profileEntryName,startAddress,endAddress Example:abc,225.0.0.0,238.0.0.1 |
| 1.3.6.1.4.1.867.100.11.214 | ScalarigmpFilteringProfileProfileEntryCount | read-only | mandatory | The number of profile entry. |
| 1.3.6.1.4.1.867.100.11.215 | ScalarigmpFilteringProfileRuleEntryCount | read-only | mandatory | The number of rule entry. |
| 1.3.6.1.4.1.867.100.12 | Nodedot1xMgt | |||
| 1.3.6.1.4.1.867.100.12.1 | Scalardot1xEnabled | read-write | mandatory | A switch to select whether the 802.1x is port_based(1)/mac_based(2)/disable(3)/transparent(4) |
| 1.3.6.1.4.1.867.100.12.2 | ScalarreAuthEnabled | read-write | mandatory | A switch to select whether the re-authentication function is enable/disable |
| 1.3.6.1.4.1.867.100.12.3 | ScalarreAuthPeriod | read-write | mandatory | A switch to select the period of re-authentication function. ((0..65535) seconds ) |
| 1.3.6.1.4.1.867.100.12.4 | ScalarreAuthMax | read-write | mandatory | A switch to select the maximun retry times of re-authentication function. (0-10) |
| 1.3.6.1.4.1.867.100.12.5 | ScalarmaxReqCount | read-write | mandatory | The number that the authenticator retires on server timeouts before it declares authentication failure. (0-10) |
| 1.3.6.1.4.1.867.100.12.6 | ScalarserverTimeout | read-write | mandatory | The timeout after an access-request is sent to the server before backend state machine retries. ((0..65535) seconds ) |
| 1.3.6.1.4.1.867.100.12.7 | ScalarsuppTimeout | read-write | mandatory | The timeout after an EAPOL authentication-request is sent to supplicant before backend state machine retries. ((0..65535) seconds ) |
| 1.3.6.1.4.1.867.100.12.8 | ScalarquietPeriod | read-write | mandatory | The timeout after a failure before authenticator re-tries to authenticate a supplicant. ((0..65535) seconds ) |
| 1.3.6.1.4.1.867.100.12.9 | ScalartxPeriod | read-write | mandatory | The timeout after an EAPOL identify-request is sent to supplicant before authenticator state machine retries. ((0..65535) seconds ) |
| 1.3.6.1.4.1.867.100.12.14 | Scalardot1xguestvlan | read-write | mandatory | It selects guest vlan vid or disable(0). |
| 1.3.6.1.4.1.867.100.12.15 | Scalardot1xdynamicvlan | read-write | mandatory | It selects dynamic vlan enable or disable. |
| 1.3.6.1.4.1.867.100.12.16 | TableportAuthModeTable | not-accessible | mandatory | The authentication mode of port in 802.1x. |
| 1.3.6.1.4.1.867.100.12.16.1 | RowportAuthModeEntry | not-accessible | mandatory | For 802.1p frame, mapping the 802.1p pri[2:0] (priority tag) to the priority queue of the system. |
| 1.3.6.1.4.1.867.100.12.16.1.1 | ColumnportDot1xIndex | read-only | mandatory | This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.867.100.12.16.1.2 | ColumnportAuthMode | read-write | mandatory | The authentocation mode of port. 1.ForceUnauthorized, 2.ForceAuthorized, 3.Auto, 4.None |
| 1.3.6.1.4.1.867.100.12.17 | TablemacBasedStateTable | not-accessible | mandatory | Show mac-based 802.1x authenticator state. |
| 1.3.6.1.4.1.867.100.12.17.1 | RowmacBasedStateEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.12.17.1.1 | ColumnmacBasedStateIndex | read-only | mandatory | Mac based state index. |
| 1.3.6.1.4.1.867.100.12.17.1.2 | ColumnauthVid | read-only | mandatory | The vid of Authenticator. |
| 1.3.6.1.4.1.867.100.12.17.1.3 | ColumnauthMac | read-only | mandatory | The mac address of Authenticator. |
| 1.3.6.1.4.1.867.100.12.17.1.4 | ColumnauthPort | read-only | mandatory | The port of Authenticator. |
| 1.3.6.1.4.1.867.100.12.20 | TablestandbyRadiusServerTable | not-accessible | mandatory | Radius server configuration. |
| 1.3.6.1.4.1.867.100.12.20.1 | RowstandbyRadiusServerEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.12.20.1.1 | ColumnstandbyRadiusServerIndex | read-only | mandatory | Radius server index. |
| 1.3.6.1.4.1.867.100.12.20.1.2 | ColumnstandbyRadiusServerActive | read-write | mandatory | A switch to select whether the radius server active is Yes(1)/No(2). |
| 1.3.6.1.4.1.867.100.12.20.1.3 | ColumnstandbyRadiusServerIp | read-write | mandatory | The IP address of the radius server. |
| 1.3.6.1.4.1.867.100.12.20.1.4 | ColumnstandbyRadiusServerAuthPort | read-write | mandatory | The port of radius server. It is between 1 and 65535. |
| 1.3.6.1.4.1.867.100.12.20.1.5 | ColumnstandbyRadiusServerSecurityKey | read-write | mandatory | The key in calculating MD5 encryption for enconding/deconding the Mesage-Authenticator in RADIUS packets. |
| 1.3.6.1.4.1.867.100.12.20.1.6 | ColumnstandbyRadiusServerRunning | read-only | mandatory | The running state of radius server. Running state: Yes(1)/No(2). |
| 1.3.6.1.4.1.867.100.12.231 | ScalarmacBasedReauthPort | read-create | current | Reauthenticate ethernet port(s). |
| 1.3.6.1.4.1.867.100.12.232 | ScalarmacBasedReauthMac | read-write | mandatory | Reauthenticate MAC address. |
| 1.3.6.1.4.1.867.100.12.233 | ScalaraaaLogin | read-write | mandatory | A switch to define login authentication method/precedence is local(1)/radius(2)/local_radius(3). |
| 1.3.6.1.4.1.867.100.13 | NodemacsecMgt | |||
| 1.3.6.1.4.1.867.100.13.1 | ScalarmacsecEnabled | read-write | mandatory | A switch to select whether the MAC security is enable/disable |
| 1.3.6.1.4.1.867.100.13.2 | TablemacsecModeTable | not-accessible | mandatory | The security mode of port in MAC Security. |
| 1.3.6.1.4.1.867.100.13.2.1 | RowmacsecModeEntry | not-accessible | mandatory | The MAC Security Mode Entry. |
| 1.3.6.1.4.1.867.100.13.2.1.1 | ColumnportmacsecIndex | read-only | mandatory | This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.867.100.13.2.1.2 | ColumnportmacsecMode | read-write | mandatory | The security mode of port. 1.NoSecurity 2.STATICWITHACCEPT 3.LIMITBYMACNO |
| 1.3.6.1.4.1.867.100.13.2.1.3 | Columnportmaxmacno | read-write | mandatory | The max mac number of port. The value is rang 0 and 8192. |
| 1.3.6.1.4.1.867.100.13.2.1.4 | Columnportlearnmacno | read-only | mandatory | The learned mac number of port. |
| 1.3.6.1.4.1.867.100.14 | NoderatecontrolMgt | |||
| 1.3.6.1.4.1.867.100.14.1 | ScalaringressEgressRateControl | read-write | mandatory | A switch to select Packet Drop for ingress Limit whether the is enable/disable. |
| 1.3.6.1.4.1.867.100.14.2 | TablercIngressPortTable | not-accessible | mandatory | The information for Ingress Rate Control of per port. |
| 1.3.6.1.4.1.867.100.14.2.1 | RowrcIngressPortEntry | not-accessible | mandatory | Ingress Rate Control information entry. |
| 1.3.6.1.4.1.867.100.14.2.1.1 | ColumnrcIngressPortIndex | read-only | mandatory | |
| 1.3.6.1.4.1.867.100.14.2.1.2 | ColumnrcIngressCount | read-write | mandatory | A switch to select Ingress Count whether it is between 0 and 1000. When it is 0 ,No limit. |
| 1.3.6.1.4.1.867.100.14.2.1.3 | ColumnrcIngressUnit | read-write | mandatory | A switch to select Ingress Unit whether it is 1=1Mbps/2=62.5kbps |
| 1.3.6.1.4.1.867.100.14.2.1.4 | ColumnrcIngressRate | read-only | mandatory | The Ingress rate is unit*count kbps. No limite ,when the value is 0. |
| 1.3.6.1.4.1.867.100.14.3 | TablercEgressPortTable | not-accessible | mandatory | The information for Egress Rate Control of per port. |
| 1.3.6.1.4.1.867.100.14.3.1 | RowrcEgressPortEntry | not-accessible | mandatory | Engress Rate Control information entry. |
| 1.3.6.1.4.1.867.100.14.3.1.1 | ColumnrcEgressPortIndex | read-only | mandatory | |
| 1.3.6.1.4.1.867.100.14.3.1.2 | ColumnrcEgressCount | read-write | mandatory | A switch to select Egress Count whether it is between 0 and 1000. When it is 0 ,No limit. |
| 1.3.6.1.4.1.867.100.14.3.1.3 | ColumnrcEgressUnit | read-write | mandatory | A switch to select Egress Unit whether it is 1=1Mbps/2=62.5kbps |
| 1.3.6.1.4.1.867.100.14.3.1.4 | ColumnrcEgressRate | read-only | mandatory | The Egress rate is unit*count kbps. No limite ,when the value is 0. |
| 1.3.6.1.4.1.867.100.15 | NodestormcontrolMgt | |||
| 1.3.6.1.4.1.867.100.15.2 | TableconfbyportTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.15.2.1 | RowconfbyportEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.15.2.1.1 | Columnportindex | read-only | mandatory | The port index of Storm Control. |
| 1.3.6.1.4.1.867.100.15.2.1.2 | Columnbroadcastbyport | read-write | mandatory | A switch to select on/off of Broadcast Control by port. |
| 1.3.6.1.4.1.867.100.15.2.1.3 | Columnmulticastbyport | read-write | mandatory | A switch to select on/off of Multicast Control by port. |
| 1.3.6.1.4.1.867.100.15.2.1.4 | Columnfloodingbyport | read-write | mandatory | A switch to select on/off of Flooding Control by port. |
| 1.3.6.1.4.1.867.100.15.201 | Scalarscuint | read-write | mandatory | A switch to select Suppression Unit Rate(1=62.5Kbps/2=1Mbps) of Storm Control. |
| 1.3.6.1.4.1.867.100.15.202 | Scalarsccount | read-write | mandatory | A switch to select N of Storm Control (Suppression Rate = N*Unit). When it is 0 ,NO limit. |
| 1.3.6.1.4.1.867.100.16 | NodeloggingMgt | |||
| 1.3.6.1.4.1.867.100.16.1 | ScalarsystemLogEnable | read-write | mandatory | A switch to select whether the System Log Setting is enable/disable |
| 1.3.6.1.4.1.867.100.16.2 | ScalarsystemLogLevel | read-write | mandatory | A switch to select whether the System Log Level is (0-7) |
| 1.3.6.1.4.1.867.100.16.3 | ScalarsystemRemotelog | read-write | mandatory | A switch to select whether the System Remote Log Setting is enable/disable. When it is enable,Remote Log Server IP can not be empty |
| 1.3.6.1.4.1.867.100.16.4 | TablesystemServerIPTable | not-accessible | mandatory | The information for system server ip. |
| 1.3.6.1.4.1.867.100.16.4.1 | RowsystemServerIPEntry | not-accessible | mandatory | System log of server ip information entry. |
| 1.3.6.1.4.1.867.100.16.4.1.1 | ColumnsystemServerIPIndex | read-only | mandatory | A switch to select the index of System Log Server IP |
| 1.3.6.1.4.1.867.100.16.4.1.2 | ColumnsystemServerIP | read-write | mandatory | A switch to specify the System Log Server IP. When the value is null,the Server IP Address is nill. |
| 1.3.6.1.4.1.867.100.17 | Nodeoption82Mgt | |||
| 1.3.6.1.4.1.867.100.17.1 | Scalardhcprelaystatus | read-write | mandatory | A switch to select whether the dhcp relay status is ON or OFF. The default is OFF. |
| 1.3.6.1.4.1.867.100.17.2 | Scalaroption82relaystatus | read-write | mandatory | A switch to select whether the dhcp option 82 relay status is ON or OFF. The default is OFF. |
| 1.3.6.1.4.1.867.100.17.4 | Scalaraddinformationstate | read-write | mandatory | A switch to select whether the relay agent ioformation state. |
| 1.3.6.1.4.1.867.100.17.5 | Scalaraddinformation | read-write | mandatory | Relay Agent ioformation |
| 1.3.6.1.4.1.867.100.17.6 | Scalaroption82serverip | read-write | mandatory | A switch to set up the dhcp server ip address |
| 1.3.6.1.4.1.867.100.18 | NodemvrMgt | |||
| 1.3.6.1.4.1.867.100.18.1 | TablemvrConfTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.18.1.1 | RowmvrConfEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.18.1.1.1 | Columnmvrindex | read-only | mandatory | The item of Multicast Vlan. |
| 1.3.6.1.4.1.867.100.18.1.1.2 | Columnmvrname | read-write | mandatory | A switch to select Name of Multicast Vlan. |
| 1.3.6.1.4.1.867.100.18.1.1.3 | Columnmvractive | read-write | mandatory | A switch to select active or nactive of Multicast Vlan. |
| 1.3.6.1.4.1.867.100.18.1.1.4 | Columnaddmvrvid | read-write | mandatory | A switch to select vid of Multicast Vlan . |
| 1.3.6.1.4.1.867.100.18.1.1.5 | Columnmvrpriority | read-write | mandatory | A switch to select 802.1p Priority of Multicast Vlan . |
| 1.3.6.1.4.1.867.100.18.1.1.6 | Columnmvrmode | read-write | mandatory | A switch to select Mode of Multicast Vlan . |
| 1.3.6.1.4.1.867.100.18.1.1.7 | Columnmvrsourceport | read-create | current | A switch to select SourcePort of Multicast Vlan. |
| 1.3.6.1.4.1.867.100.18.1.1.8 | Columnmvrreceiveport | read-create | current | A switch to select ReceivePort of Multicast Vlan. |
| 1.3.6.1.4.1.867.100.18.1.1.9 | Columnmvrtag | read-create | current | A switch to select Tag of Multicast Vlan. |
| 1.3.6.1.4.1.867.100.18.1.1.10 | Columnmvrdelete | read-write | mandatory | A switch to select Mode of Multicast Vlan . |
| 1.3.6.1.4.1.867.100.18.2 | TablemvrGroupaddTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.18.2.1 | RowmvrGroupaddEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.18.2.1.1 | Columnmvrgroupindex | read-only | mandatory | The item of MVR Group VLAN. |
| 1.3.6.1.4.1.867.100.18.2.1.2 | Columnmvrgroupvid | read-only | mandatory | A switch to select Vlan id of Multicast Group Vlan. |
| 1.3.6.1.4.1.867.100.18.2.1.3 | Columnmvrgroupaddname | read-write | mandatory | A switch to select Name of Multicast Group Vlan. |
| 1.3.6.1.4.1.867.100.18.2.1.4 | ColumnmvrgroupaddIPrange | read-write | mandatory | A switch to select start ipaddress of Multicast Group Vlan. |
| 1.3.6.1.4.1.867.100.18.2.1.5 | ColumnmvrgroupDeleteEntry | read-write | mandatory | To delete group entry. Format:vid,groupEntryName Example:100,abc |
| 1.3.6.1.4.1.867.100.18.3 | TablemvrGroup1_Table | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.18.3.1 | RowmvrGroup1_Entry | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.18.3.1.1 | Columnmvrgroupindex_1 | read-only | mandatory | The item of MVR Group VLAN. |
| 1.3.6.1.4.1.867.100.18.3.1.2 | Columnmvrgroupid_1 | read-only | mandatory | A switch to select Vlan id of Multicast Group Vlan. |
| 1.3.6.1.4.1.867.100.18.3.1.3 | Columnmvrgroupname_1 | read-only | mandatory | A switch to select Name of Multicast Group Vlan. |
| 1.3.6.1.4.1.867.100.18.3.1.4 | Columnmvrgroupstartip_1 | read-only | mandatory | A switch to select start ipaddress of Multicast Group Vlan. |
| 1.3.6.1.4.1.867.100.18.3.1.5 | Columnmvrgroupendip_1 | read-only | mandatory | A switch to select end ipaddress of Multicast Group Vlan. |
| 1.3.6.1.4.1.867.100.18.4 | TablemvrGroup2_Table | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.18.4.1 | RowmvrGroup2_Entry | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.18.4.1.1 | Columnmvrgroupindex_2 | read-only | mandatory | The item of MVR Group VLAN. |
| 1.3.6.1.4.1.867.100.18.4.1.2 | Columnmvrgroupid_2 | read-only | mandatory | A switch to select Vlan id of Multicast Group Vlan. |
| 1.3.6.1.4.1.867.100.18.4.1.3 | Columnmvrgroupname_2 | read-only | mandatory | A switch to select Name of Multicast Group Vlan. |
| 1.3.6.1.4.1.867.100.18.4.1.4 | Columnmvrgroupstartip_2 | read-only | mandatory | A switch to select start ipaddress of Multicast Group Vlan. |
| 1.3.6.1.4.1.867.100.18.4.1.5 | Columnmvrgroupendip_2 | read-only | mandatory | A switch to select end ipaddress of Multicast Group Vlan. |
| 1.3.6.1.4.1.867.100.18.5 | TablemvrGroup3_Table | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.18.5.1 | RowmvrGroup3_Entry | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.18.5.1.1 | Columnmvrgroupindex_3 | read-only | mandatory | The item of MVR Group VLAN. |
| 1.3.6.1.4.1.867.100.18.5.1.2 | Columnmvrgroupid_3 | read-only | mandatory | A switch to select Vlan id of Multicast Group Vlan. |
| 1.3.6.1.4.1.867.100.18.5.1.3 | Columnmvrgroupname_3 | read-only | mandatory | A switch to select Name of Multicast Group Vlan. |
| 1.3.6.1.4.1.867.100.18.5.1.4 | Columnmvrgroupstartip_3 | read-only | mandatory | A switch to select start ipaddress of Multicast Group Vlan. |
| 1.3.6.1.4.1.867.100.18.5.1.5 | Columnmvrgroupendip_3 | read-only | mandatory | A switch to select end ipaddress of Multicast Group Vlan. |
| 1.3.6.1.4.1.867.100.19 | NodeipmacMgt | |||
| 1.3.6.1.4.1.867.100.19.1 | TableipmacConfTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.19.1.1 | RowipmacConfEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.19.1.1.1 | Columnipmacindex | read-only | mandatory | |
| 1.3.6.1.4.1.867.100.19.1.1.2 | Columnipmacportenable | read-write | mandatory | A switch to select Enable/Disable of IP MAC Binding in port. |
| 1.3.6.1.4.1.867.100.19.2 | TableipmacBindingTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.19.2.1 | RowipmacBindingEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.19.2.1.1 | Columnipmacruleindex | read-only | mandatory | |
| 1.3.6.1.4.1.867.100.19.2.1.2 | Columnipmacruleactive | read-write | mandatory | A switch to select active/noactive of Address Binding List. |
| 1.3.6.1.4.1.867.100.19.2.1.3 | ColumnipmacSrcMac | read-write | mandatory | A switch to select Source MAC Address of Address Binding List. |
| 1.3.6.1.4.1.867.100.19.2.1.4 | ColumnipmacSrcIP | read-write | mandatory | A switch to select Source IP Address of Address Binding List. |
| 1.3.6.1.4.1.867.100.19.2.1.5 | ColumnipmacSrcPort | read-write | mandatory | A switch to select Source Port of Address Binding List. |
| 1.3.6.1.4.1.867.100.19.3 | Scalaripmacdeleteall | read-write | mandatory | A switch to select delete all of Address Binding List. |
| 1.3.6.1.4.1.867.100.20 | NodeaclMgt | |||
| 1.3.6.1.4.1.867.100.20.1 | ScalaraclFunction | read-write | mandatory | A switch to select whether acl function is enable/disable |
| 1.3.6.1.4.1.867.100.20.2 | ScalaracMaxRule | read-only | mandatory | To support Max Rule |
| 1.3.6.1.4.1.867.100.20.3 | TableaclConfTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.20.3.1 | RowaclConfEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.20.3.1.1 | ColumnaclRuleNo | read-only | mandatory | This is the number of the rule |
| 1.3.6.1.4.1.867.100.20.3.1.2 | ColumnaclRuleActive | read-write | mandatory | This is to assign the the rule to be active/in-active |
| 1.3.6.1.4.1.867.100.20.3.1.3 | ColumnaclRuleName | read-write | mandatory | Name of the rule. |
| 1.3.6.1.4.1.867.100.20.3.1.4 | ColumnaclRuleL2Frame | read-write | mandatory | This is to assign the value of L2 Frame |
| 1.3.6.1.4.1.867.100.20.3.1.5 | ColumnaclRuleSrcMac | read-write | mandatory | This is to assign the value of Source MAC Address |
| 1.3.6.1.4.1.867.100.20.3.1.6 | ColumnaclRuleSrcMacBitMask | read-write | mandatory | This is to assign the value of Source MAC Address Bit Mask, If the value is 00 00 00 00 00 00, it works ANY |
| 1.3.6.1.4.1.867.100.20.3.1.7 | ColumnaclRuleDestMac | read-write | mandatory | This is to assign the value of Destination MAC Address |
| 1.3.6.1.4.1.867.100.20.3.1.8 | ColumnaclRuleDestMacBitMask | read-write | mandatory | This is to assign the value of Destination MAC Address Bit Mask, If the value is 00 00 00 00 00 00, it works ANY |
| 1.3.6.1.4.1.867.100.20.3.1.9 | ColumnaclRuleTaggedFrame | read-write | mandatory | This is to assign the value of Tagged Frame |
| 1.3.6.1.4.1.867.100.20.3.1.10 | ColumnaclRuleVLAN | read-write | mandatory | This is to assign the value of VLAN , if vlan>4095, any |
| 1.3.6.1.4.1.867.100.20.3.1.11 | ColumnaclRuleEthernetTypeAny | read-write | mandatory | This is to assign the value of Ethernet Type to be ANY |
| 1.3.6.1.4.1.867.100.20.3.1.12 | ColumnaclRuleEthernetType | read-write | mandatory | This is to assign the value of Ethernet Type |
| 1.3.6.1.4.1.867.100.20.3.1.13 | ColumnaclRuleL3Frame | read-write | mandatory | This is to assign the value of L3 Frame |
| 1.3.6.1.4.1.867.100.20.3.1.14 | ColumnaclRuleSrcIp | read-write | mandatory | This is to assign the value of Source IP Address Prefix |
| 1.3.6.1.4.1.867.100.20.3.1.15 | ColumnaclRuleSrcIpAddressPrefix | read-write | mandatory | This is to assign the value of Source IP Address Prefix |
| 1.3.6.1.4.1.867.100.20.3.1.16 | ColumnaclRuleDestIp | read-write | mandatory | This is to assign the value of Destination IP Address Prefix |
| 1.3.6.1.4.1.867.100.20.3.1.17 | ColumnaclRuleDestIpAddressPrefix | read-write | mandatory | This is to assign the value of Destination IP Address Prefix |
| 1.3.6.1.4.1.867.100.20.3.1.18 | ColumnaclRuleIpProtocolAny | read-write | mandatory | This is to assign the value of IP Protocol to be ANY |
| 1.3.6.1.4.1.867.100.20.3.1.19 | ColumnaclRuleIpProtocol | read-write | mandatory | This is to assign the value of IP Protocol |
| 1.3.6.1.4.1.867.100.20.3.1.20 | ColumnaclRuleL4Frame | read-write | mandatory | This is to assign the value of L4 Frame |
| 1.3.6.1.4.1.867.100.20.3.1.21 | ColumnaclRuleSourceSocketPortNumberANY | read-write | mandatory | This is to assign the value of Source Socket Port Number to ANY |
| 1.3.6.1.4.1.867.100.20.3.1.22 | ColumnaclRuleSourceSocketPortNumber | read-write | mandatory | This is to assign the value of Source Socket Port Number |
| 1.3.6.1.4.1.867.100.20.3.1.23 | ColumnaclRuleDestinationSocketPortNumberANY | read-write | mandatory | This is to assign the value of Destination Socket Port Number to ANY |
| 1.3.6.1.4.1.867.100.20.3.1.24 | ColumnaclRuleDestinationSocketPortNumber | read-write | mandatory | This is to assign the value of Destination Socket Port Number |
| 1.3.6.1.4.1.867.100.20.3.1.25 | ColumnaclRuleSrcPort | read-write | mandatory | |
| 1.3.6.1.4.1.867.100.20.3.1.26 | ColumnaclRuleAction | read-write | mandatory | This is to assign Policy/Action |
| 1.3.6.1.4.1.867.100.20.3.1.27 | ColumnaclRuleActionFloodToOnePort | read-write | mandatory | This is to assign the port in Flood_To_One_port mode of Policy/Action |
| 1.3.6.1.4.1.867.100.20.3.1.28 | ColumnaclRuleAcRateLimit | read-write | mandatory | This is to assign the rate limit , 0= no limit |
| 1.3.6.1.4.1.867.100.20.3.1.29 | ColumnaclRuleAcRateUnit | read-write | mandatory | This is to assign the rate unit 0=62.5k/1=1M |
| 1.3.6.1.4.1.867.100.21 | NodeloopbackMgt | |||
| 1.3.6.1.4.1.867.100.21.1 | TableloopbackConfTable | not-accessible | mandatory | A Switch set up loopback configuration for each port. |
| 1.3.6.1.4.1.867.100.21.1.1 | RowloopbackConfEntry | not-accessible | mandatory | Port loopback information entry. |
| 1.3.6.1.4.1.867.100.21.1.1.1 | ColumnportLoopbackIndex | read-only | mandatory | port number, This is defined as ifIndex in the IF-MIB. |
| 1.3.6.1.4.1.867.100.21.1.1.2 | ColumnportloopbackEnable | read-write | mandatory | Port loopback detection function is enabled/disabled. |
| 1.3.6.1.4.1.867.100.21.1.1.3 | ColumnportloopbackControl | read-write | mandatory | Configure the Switch to enable/disable to shutdown the current port once the port is found in a loop |
| 1.3.6.1.4.1.867.100.21.1.1.4 | ColumnportloopbackInShutdown | read-write | mandatory | The port is in Shutdown |
| 1.3.6.1.4.1.867.100.21.1.1.5 | ColumnportloopbackInLoop | read-only | mandatory | The port is in a loop |
| 1.3.6.1.4.1.867.100.22 | NodedhcpsnoopMgt | |||
| 1.3.6.1.4.1.867.100.22.2 | TableportConfTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.22.2.1 | RowportConfEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.22.2.1.1 | Columndhcpsnoopportindex | read-only | mandatory | |
| 1.3.6.1.4.1.867.100.22.2.1.2 | Columndhcpsnooptrust | read-write | mandatory | A switch to select Trust/Untrust port of DHCP SNOOPING. |
| 1.3.6.1.4.1.867.100.22.2.1.3 | Columndhcpsnooprate | read-write | mandatory | A switch to select dhcp snooping rate whether it is between 0 and 5 (*62.5 Kbps). When it is 0 ,No limit. |
| 1.3.6.1.4.1.867.100.22.3 | TabledhcpsnoopTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.22.3.1 | RowdhcpsnoopEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.22.3.1.1 | Columntableindex | read-only | mandatory | |
| 1.3.6.1.4.1.867.100.22.3.1.2 | Columndhcpsnoopvid | read-only | mandatory | A switch to show dhcp snooping table of VID. |
| 1.3.6.1.4.1.867.100.22.3.1.3 | Columndhcpsnoopip | read-only | mandatory | A switch to show dhcp snooping table of ip address. |
| 1.3.6.1.4.1.867.100.22.3.1.4 | Columndhcpsnoopmac | read-only | mandatory | A switch to show dhcp snooping table of MAC. |
| 1.3.6.1.4.1.867.100.22.3.1.5 | Columndhcpsnooplease | read-only | mandatory | A switch to show dhcp snooping table of Lease time. |
| 1.3.6.1.4.1.867.100.22.3.1.6 | Columndhcpsnoopport | read-only | mandatory | A switch to show dhcp snooping table of port. |
| 1.3.6.1.4.1.867.100.22.201 | Scalardhcpsnoopstatus | read-write | mandatory | A switch to select whether the dhcp snoop status is ON or OFF. The default is OFF. |
| 1.3.6.1.4.1.867.100.22.202 | Scalardhcpsnoopwrite | read-write | mandatory | A switch to select whether the dhcp Write delay status is ON or OFF. The default is OFF. |
| 1.3.6.1.4.1.867.100.22.203 | Scalardhcpsnoopwritedelay | read-write | mandatory | A switch to select whether the dhcp Write delay time is between 10 and 65535. The default is 10. |
| 1.3.6.1.4.1.867.100.22.204 | Scalardhcpsnoopfile | read-write | mandatory | The filename of dhcp snooping table |
| 1.3.6.1.4.1.867.100.22.205 | Scalardhcpsnoopagentip | read-write | mandatory | A switch to set up the tftp server ip address |
| 1.3.6.1.4.1.867.100.22.206 | Scalardhcpsnooprenew | read-write | mandatory | A switch to select whether the dhcp snoop status is renew. |
| 1.3.6.1.4.1.867.100.23 | NodelldpMgt | |||
| 1.3.6.1.4.1.867.100.23.3 | TablelldpPortConfTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.23.3.1 | RowlldpPortConfEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.23.3.1.1 | ColumnlldpPortIndex | read-only | mandatory | The port number of lldp, |
| 1.3.6.1.4.1.867.100.23.3.1.2 | ColumnlldpPortstate | read-write | mandatory | A switch to select LLDP port state whether it is disabled/RX and TX/TX only/RX only |
| 1.3.6.1.4.1.867.100.23.4 | TablelldplistTable | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.23.4.1 | RowlldplistEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.867.100.23.4.1.1 | ColumnlldpIdIndex | read-only | mandatory | The id of lldp table list, |
| 1.3.6.1.4.1.867.100.23.4.1.2 | ColumnlldpPortID | read-only | mandatory | It is local Port. |
| 1.3.6.1.4.1.867.100.23.4.1.3 | ColumnlldpChassid | read-only | mandatory | The Chassis ID of lldp. |
| 1.3.6.1.4.1.867.100.23.4.1.4 | ColumnlldpRemotePortid | read-only | mandatory | The Remote Port ID of lldp. |
| 1.3.6.1.4.1.867.100.23.4.1.5 | ColumnlldpTimelive | read-only | mandatory | The Time to live of lldp. |
| 1.3.6.1.4.1.867.100.23.4.1.6 | ColumnlldpPortDescr | read-only | mandatory | The Port Description of remote switch. |
| 1.3.6.1.4.1.867.100.23.4.1.7 | ColumnlldpSystemName | read-only | mandatory | The System Description of remote switch. |
| 1.3.6.1.4.1.867.100.23.4.1.8 | ColumnlldpSystDescr | read-only | mandatory | The System Description of remote switch. |
| 1.3.6.1.4.1.867.100.23.4.1.9 | ColumnlldpSystemCapa | read-only | mandatory | The System Capabilities of remote switch. |
| 1.3.6.1.4.1.867.100.23.4.1.10 | ColumnlldpMamgtAddr | read-only | mandatory | The Management Address of remote switch. |
| 1.3.6.1.4.1.867.100.23.201 | Scalarlldpstate | read-write | mandatory | A switch to select whether the lldp status is ON or OFF. The default is OFF. |
| 1.3.6.1.4.1.867.100.23.202 | Scalarlldpportdesrstate | read-write | mandatory | The Transmitted TLVs of lldp whether the Port Description is ON or OFF. The default is ON. |
| 1.3.6.1.4.1.867.100.23.203 | Scalarlldpsystemnamestate | read-write | mandatory | The Transmitted TLVs of lldp whether the System Name is ON or OFF. The default is ON. |
| 1.3.6.1.4.1.867.100.23.204 | Scalarlldpsystemdescrstate | read-write | mandatory | The Transmitted TLVs of lldp whether the System Description is ON or OFF. The default is ON. |
| 1.3.6.1.4.1.867.100.23.205 | Scalarlldpsystemcapastate | read-write | mandatory | The Transmitted TLVs of lldp whether the System Capabilities is ON or OFF. The default is ON. |
| 1.3.6.1.4.1.867.100.23.206 | Scalarlldpmgmtaddrstate | read-write | mandatory | The Transmitted TLVs of lldp whether the Management Address is ON or OFF. The default is ON. |
| 1.3.6.1.4.1.867.100.23.211 | ScalarlldpInterval | read-write | mandatory | A switch to select whether the lldp Interval. The default is 30. . |
| 1.3.6.1.4.1.867.100.23.212 | ScalarlldpTxhold | read-write | mandatory | A switch to select whether the lldp Tx Hold. The default is 4. . |
| 1.3.6.1.4.1.867.100.23.213 | ScalarlldpTxdelay | read-write | mandatory | A switch to select whether the lldp Tx Delay. The default is 2. . |
| 1.3.6.1.4.1.867.100.23.214 | ScalarlldpReinitdelay | read-write | mandatory | A switch to select whether the lldp Reinit Delay. The default is 2. . |
| 1.3.6.1.4.1.867.100.100 | Nodeswitch_Reset | Successfully reset the switching hub. | ||
| 1.3.6.1.4.1.867.100.101 | Nodeswitch_FReset | Fattory reset of the switching hub is successful. | ||
| 1.3.6.1.4.1.867.100.110 | Nodeswitch_Port_Enabled | Enable a port. | ||
| 1.3.6.1.4.1.867.100.111 | Nodeswitch_Port_Disabled | Disable a port. | ||
| 1.3.6.1.4.1.867.100.120 | Nodeswitch_Port_Speed_Duplex_Change | Speed & Duplex status of the switching port is changed. | ||
| 1.3.6.1.4.1.867.100.140 | Nodeswitch_Port_Mirror_On | Enable port Mirror function. | ||
| 1.3.6.1.4.1.867.100.141 | Nodeswitch_Port_Mirror_Off | Disable port Mirror function. | ||
| 1.3.6.1.4.1.867.100.150 | Nodeswitch_Virtual_LAN_On | Enable Virtual LAN function. | ||
| 1.3.6.1.4.1.867.100.151 | Nodeswitch_Virtual_LAN_Off | Disable Virtual LAN function. | ||
| 1.3.6.1.4.1.867.100.152 | Nodeswitch_VL_ReConfiguration | VLAN re-configuration. | ||
| 1.3.6.1.4.1.867.100.160 | Nodeswitch_Port_Trunk_On | Enable Port Trunk function. | ||
| 1.3.6.1.4.1.867.100.161 | Nodeswitch_Port_Trunk_Off | Disable Port Trunk function. | ||
| 1.3.6.1.4.1.867.100.162 | Nodeswitch_Port_Trunk_ReConfigure | One Port Trunk group re-configure. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| BitList | OCTET STRING | current | |
| MacAddress | OCTET STRING (SIZE (6)) | ||
| PortList | OCTET STRING | current | Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents… |