SYNC-RESEARCH-MIB

1070 objects

No module-level DESCRIPTION found.

Imported Objects

RFC-1212	OBJECT-TYPE
RFC-1215	--syncResearch --FROM SYNC-RESEARCH-COMMUNITY-MIB TRAP-TYPE
RFC1155-SMI	--internet --TimeTicks Counter enterprises enterprises Gauge IpAddress mgmt NetworkAddress

OID	Name	Access	Status	Description
1.3.6.1.4.1.485	NodesyncResearch
1.3.6.1.4.1.485.1	NodesyncResearchAgent
1.3.6.1.4.1.485.1.1	NodesyncProducts
1.3.6.1.4.1.485.1.1.1	Nodeboundary
1.3.6.1.4.1.485.1.1.1.1	NodesyncCN2R2b
1.3.6.1.4.1.485.1.1.1.2	NodesyncFN2R2b
1.3.6.1.4.1.485.1.1.1.3	NodesyncCN4R2b
1.3.6.1.4.1.485.1.1.1.4	NodesyncFN4R2b
1.3.6.1.4.1.485.1.1.1.5	NodesyncQN4R2b
1.3.6.1.4.1.485.1.1.1.6	NodesyncCN4R3b
1.3.6.1.4.1.485.1.1.1.7	NodesyncFN4R3b
1.3.6.1.4.1.485.1.1.1.8	NodesyncQN4R3b
1.3.6.1.4.1.485.1.1.1.9	NodesyncCN4R4b
1.3.6.1.4.1.485.1.1.1.10	NodesyncFN4R4b
1.3.6.1.4.1.485.1.1.1.11	NodesyncQN4R4b
1.3.6.1.4.1.485.1.1.1.12	NodesyncCN4R4bu
1.3.6.1.4.1.485.1.1.1.13	NodesyncFN4R4bu
1.3.6.1.4.1.485.1.1.1.14	NodesyncQN4R4bu
1.3.6.1.4.1.485.1.1.1.15	NodesyncCN4R4du
1.3.6.1.4.1.485.1.1.1.16	NodesyncFN4R4du
1.3.6.1.4.1.485.1.1.1.17	NodesyncQN4R4du
1.3.6.1.4.1.485.1.1.1.18	NodesyncCN2R2du
1.3.6.1.4.1.485.1.1.1.19	NodesyncFN2R2du
1.3.6.1.4.1.485.1.1.1.20	NodesyncCN3R4bu
1.3.6.1.4.1.485.1.1.1.21	NodesyncFN3R4bu
1.3.6.1.4.1.485.1.1.1.22	NodesyncCN3R4du
1.3.6.1.4.1.485.1.1.1.23	NodesyncFN3R4du
1.3.6.1.4.1.485.1.1.1.24	NodesyncCN4R5b
1.3.6.1.4.1.485.1.1.1.25	NodesyncFN4R5b
1.3.6.1.4.1.485.1.1.1.26	NodesyncQN4R5b
1.3.6.1.4.1.485.1.1.1.27	NodesyncCN4R5bu
1.3.6.1.4.1.485.1.1.1.28	NodesyncFN4R5bu
1.3.6.1.4.1.485.1.1.1.29	NodesyncQN4R5bu
1.3.6.1.4.1.485.1.1.1.30	NodesyncCN4R5du
1.3.6.1.4.1.485.1.1.1.31	NodesyncFN4R5du
1.3.6.1.4.1.485.1.1.1.32	NodesyncQN4R5du
1.3.6.1.4.1.485.1.1.1.33	NodesyncFN5R5du
1.3.6.1.4.1.485.1.1.1.34	NodesyncBC4R5b
1.3.6.1.4.1.485.1.1.1.35	NodesyncBF4R5b
1.3.6.1.4.1.485.1.1.1.36	NodesyncBF3R5b
1.3.6.1.4.1.485.1.1.1.37	NodesyncBF5R5b
1.3.6.1.4.1.485.1.1.1.38	NodesyncFN3R5du
1.3.6.1.4.1.485.1.1.1.39	NodesyncCN3R5du
1.3.6.1.4.1.485.1.1.1.40	NodesyncCN5R5du
1.3.6.1.4.1.485.1.1.1.41	NodesyncBF3R5
1.3.6.1.4.1.485.1.1.1.42	NodesyncBC3R5
1.3.6.1.4.1.485.1.1.1.43	NodesyncBF4R5
1.3.6.1.4.1.485.1.1.1.44	NodesyncBC4R5
1.3.6.1.4.1.485.1.1.1.45	NodesyncBF5R5
1.3.6.1.4.1.485.1.1.1.46	NodesyncBC5R5
1.3.6.1.4.1.485.1.1.2	NodecentralSite
1.3.6.1.4.1.485.1.1.2.1	NodesyncCN4R2c
1.3.6.1.4.1.485.1.1.2.2	NodesyncFN4R2c
1.3.6.1.4.1.485.1.1.2.3	NodesyncQN4R2c
1.3.6.1.4.1.485.1.1.2.4	NodesyncCN4R3c
1.3.6.1.4.1.485.1.1.2.5	NodesyncFN4R3c
1.3.6.1.4.1.485.1.1.2.6	NodesyncQN4R3c
1.3.6.1.4.1.485.1.1.2.7	NodesyncCN4R4u
1.3.6.1.4.1.485.1.1.2.8	NodesyncFN4R4u
1.3.6.1.4.1.485.1.1.2.9	NodesyncQN4R4u
1.3.6.1.4.1.485.1.2	NodeoemProducts
1.3.6.1.4.1.485.1.2.1	NodethreeCom
1.3.6.1.4.1.485.1.2.1.1	NodelinkConverter
1.3.6.1.4.1.485.1.2.1.2	NodelinkConverter2
1.3.6.1.4.1.485.1.2.1.3	Nodelc2EN2port
1.3.6.1.4.1.485.1.2.1.4	Nodelc2EN4port
1.3.6.1.4.1.485.1.2.1.5	Nodelc2TR2port
1.3.6.1.4.1.485.1.2.1.6	Nodelc2TR6port
1.3.6.1.4.1.485.1.2.2	NodecableTron
1.3.6.1.4.1.485.1.2.2.1	NodeoemSNACXR2C
1.3.6.1.4.1.485.1.2.2.2	NodeoemSNACXR2W
1.3.6.1.4.1.485.1.2.2.3	NodeoemSNACMR2C
1.3.6.1.4.1.485.1.2.2.4	NodeoemSNACMR2W
1.3.6.1.4.1.485.1.2.2.5	NodeoemSNACMIM2
1.3.6.1.4.1.485.1.2.2.6	NodeoemSNACXR2Q
1.3.6.1.4.1.485.1.2.2.7	NodeoemSNACMR2Q
1.3.6.1.4.1.485.1.2.2.8	NodeoemSNACXR3C
1.3.6.1.4.1.485.1.2.2.9	NodeoemSNACXR3W
1.3.6.1.4.1.485.1.2.2.10	NodeoemSNACMR3C
1.3.6.1.4.1.485.1.2.2.11	NodeoemSNACMR3W
1.3.6.1.4.1.485.1.2.2.12	NodeoemSNACXR3Q
1.3.6.1.4.1.485.1.2.2.13	NodeoemSNACMR3Q
1.3.6.1.4.1.485.1.2.2.14	NodeoemSNACXR4C
1.3.6.1.4.1.485.1.2.2.15	NodeoemSNACXR4W
1.3.6.1.4.1.485.1.2.2.16	NodeoemSNACMR4C
1.3.6.1.4.1.485.1.2.2.17	NodeoemSNACMR4W
1.3.6.1.4.1.485.1.2.2.18	NodeoemSNACXR4Q
1.3.6.1.4.1.485.1.2.2.19	NodeoemSNACMR4Q
1.3.6.1.4.1.485.1.2.3	Nodechipcom
1.3.6.1.4.1.485.1.2.4	Nodeibm
1.3.6.1.4.1.485.1.2.4.1	Nodeoem2490R22F
1.3.6.1.4.1.485.1.2.4.2	Nodeoem2490R22C
1.3.6.1.4.1.485.1.2.4.3	Nodeoem22181FR4
1.3.6.1.4.1.485.1.2.4.4	Nodeoem22181CR4
1.3.6.1.4.1.485.1.2.4.5	Nodeoem22183FR4
1.3.6.1.4.1.485.1.2.4.6	Nodeoem22183CR4
1.3.6.1.4.1.485.1.2.4.7	Nodeoem22181FR5
1.3.6.1.4.1.485.1.2.4.8	Nodeoem22181CR5
1.3.6.1.4.1.485.1.2.4.9	Nodeoem22183FR5
1.3.6.1.4.1.485.1.2.4.10	Nodeoem22183CR5
1.3.6.1.4.1.485.1.2.4.11	Nodeoem22185FR5
1.3.6.1.4.1.485.1.2.4.12	Nodeoem22185CR5
1.3.6.1.4.1.485.1.2.4.13	Nodeoem22183BF5
1.3.6.1.4.1.485.1.2.4.14	Nodeoem22183BC5
1.3.6.1.4.1.485.1.2.4.15	Nodeoem22184BF5
1.3.6.1.4.1.485.1.2.4.16	Nodeoem22184BC5
1.3.6.1.4.1.485.1.2.4.17	Nodeoem22185BF5
1.3.6.1.4.1.485.1.2.4.18	Nodeoem22185BC5
1.3.6.1.4.1.485.2	NodesrCommTrapGroup
1.3.6.1.4.1.485.2.1	ScalarcommCount	read-only	mandatory	The number of possible community name entries in the table.
1.3.6.1.4.1.485.2.2	TablecommTable	not-accessible	mandatory	This table houses the information for trivial authentication and sending traps.
1.3.6.1.4.1.485.2.2.1	RowcommEntry	not-accessible	mandatory	Each entry contains a community name and access code for SNMP trivial authentication and enable/disable traps options, as well as network and physical addressi…
1.3.6.1.4.1.485.2.2.1.1	ColumncommIndex	read-only	mandatory	A unique value for each community entry. Its value ranges between 1 and commCount.
1.3.6.1.4.1.485.2.2.1.2	ColumncommName	read-write	mandatory	A community name that will be used to access MIB objects. Each community name is associated with an access code of either NO-ACCESS, RO, RW, or SU.
1.3.6.1.4.1.485.2.2.1.3	ColumncommTrap	read-write	mandatory	This object is checked to determine if traps should be sent to the corresponding network address associated with it.
1.3.6.1.4.1.485.2.2.1.4	ColumncommIPAddr	read-write	mandatory	The network address of the device that will receive traps from the agent. This IP address also qualifies who may use this community name to access MIB objects.…
1.3.6.1.4.1.485.2.2.1.5	ColumncommMACAddr	read-only	mandatory	The physical address of the device receiving traps from the agent.
1.3.6.1.4.1.485.2.2.1.6	ColumncommAccess	read-write	mandatory	Access code assiciated with the community name of the same entry. noAccess indicates a community name with zero privileges. ro has read-only access to MIB obje…
1.3.6.1.4.1.485.3	NodesrNodeGroup
1.3.6.1.4.1.485.3.1	NodenodeUnitGroup
1.3.6.1.4.1.485.3.1.1	NodeunitControlGroup
1.3.6.1.4.1.485.3.1.1.1	ScalarunitRestart	read-write	mandatory	Setting this variable to a value of 1 will force the unit to restart. Setting this variable to any other value will cause an SNMP error. This variable always r…
1.3.6.1.4.1.485.3.1.1.2	ScalardumpOnRestart	read-write	mandatory	Setting this variable to a value of 1 will force the unit to perform a dump on restart. Setting this variable to a value of 2 will force it to not to dump on r…
1.3.6.1.4.1.485.3.1.1.3	ScalarinitiateInstall	read-write	mandatory	Setting this variable to a value of 1 will force the unit to initiate an install process. This variable always returns a value of 2.
1.3.6.1.4.1.485.3.1.1.4	ScalarinitializeStats	read-write	mandatory	Setting this variable to a value of 1 will force the unit to initialize (clear) SyncResearch proprietary statistics kept by the unit. This variable always retu…
1.3.6.1.4.1.485.3.1.1.5	ScalarclearDump	read-write	mandatory	Setting this variable to a value of 1 will force the unit to clear a dump. This variable always returns a value of 2.
1.3.6.1.4.1.485.3.1.1.6	ScalaracknowledgeAllStatuses	read-write	mandatory	This field is used for consolidating status of the unit. When this field is set to yes, the unit will mark each of the various statuses in different levels as …
1.3.6.1.4.1.485.3.1.1.7	ScalarconsolidatedUnitStatus	read-only	mandatory	This object reports the consolidted status of the unit. All acknowledged element statuses and any element statuses specified as ignored by the user are ignored…
1.3.6.1.4.1.485.3.1.1.8	ScalarhomeDialBackup	read-write	mandatory	Setting this variable to a value of 1 will force all dial backup lines to dedicated lines. Setting this variable to any other value will case an SNMP error. Th…
1.3.6.1.4.1.485.3.1.2	NodeunitStatusGroup
1.3.6.1.4.1.485.3.1.2.1	ScalarunitModel	read-only	mandatory	This variable defines the base hardware model of the unit.
1.3.6.1.4.1.485.3.1.2.2	ScalarsoftwareVersion	read-only	mandatory	The current version number of the operating software in xx.yyy where xx = major release, yyy = revision.
1.3.6.1.4.1.485.3.1.2.3	ScalarproductType	read-only	mandatory	The product type string returned is set in the MS.SYS file and defines the product name.
1.3.6.1.4.1.485.3.1.2.4	ScalarmaxPortNumber	read-only	mandatory	The maximum number of ports this unit can support (total number of serial access ports plus total number of LAN ports).
1.3.6.1.4.1.485.3.1.2.5	ScalarmaxPU	read-only	mandatory	The maximum number of PUs this unit can support (total number that can be configured).
1.3.6.1.4.1.485.3.1.2.6	ScalarmaxSession	read-only	mandatory	The maximum number of sessions this unit can support (total number that can be configured).
1.3.6.1.4.1.485.3.1.2.7	ScalarmaxDevice	read-only	mandatory	The maximum number of devices this unit can support (total number that can be configured).
1.3.6.1.4.1.485.3.1.2.8	ScalarmsBoardType	read-only	mandatory	Indicates the type of serial I/O ports on main board. It returns 1 if not expected.
1.3.6.1.4.1.485.3.1.2.9	ScalarmsExtBoardType	read-only	mandatory	Indicates the type of serial I/O ports on extension board. It returns 1 if not present.
1.3.6.1.4.1.485.3.1.2.10	ScalardumpFileStatus	read-only	mandatory	Indicates the presence of a dump file.
1.3.6.1.4.1.485.3.1.2.11	ScalardumpFileName	read-only	mandatory	The dump file name.
1.3.6.1.4.1.485.3.1.2.12	ScalarunitSerialNumber	read-only	mandatory	The base unit serial number.
1.3.6.1.4.1.485.3.1.2.13	ScalarexpansionSerialNumber	read-only	mandatory	The expansion board serial number.
1.3.6.1.4.1.485.3.1.2.14	ScalarromVersion	read-only	mandatory	The ROM version number.
1.3.6.1.4.1.485.3.1.2.15	ScalarprocessorType	read-only	mandatory	The base unit processor type.
1.3.6.1.4.1.485.3.1.2.16	ScalarchassisSlot	read-only	mandatory	If the unit is a blade in a chassis, then this variable indicates the slot number. If not applicable, a value of 99 will be returned.
1.3.6.1.4.1.485.3.1.2.17	ScalarlastTrapSeqNumber	read-only	mandatory	This entry contains the last sequence number of the last trap generated by the unit. When this value reaches its maximum, it then rolls back to 0.
1.3.6.1.4.1.485.3.1.2.18	ScalarlastInstallErrCode	read-only	mandatory	This entry contains the status of last install. If the last install was successful, 0 is returned, 9999 indicates installation is in progress, otherwise an err…
1.3.6.1.4.1.485.3.1.2.19	ScalarunitPartNumber	read-only	mandatory	The base unit part number.
1.3.6.1.4.1.485.3.1.2.20	ScalarexpansionPartNumber	read-only	mandatory	The expansion board part number.
1.3.6.1.4.1.485.3.1.2.21	Scalarwan1BoardType	read-only	mandatory	Indicates the type of serial I/O ports on extension board. It returns 1 if not present.
1.3.6.1.4.1.485.3.1.2.22	Scalarwan2BoardType	read-only	mandatory	Indicates the type of serial I/O ports on extension board. It returns 1 if not present.
1.3.6.1.4.1.485.3.1.2.23	ScalarpatchId	read-only	mandatory	The current patch identifier for the operating software. Either the three character Patch ID or 'None'
1.3.6.1.4.1.485.3.1.3	NodeunitConfigGroup
1.3.6.1.4.1.485.3.1.3.1	ScalarunitId	read-only	mandatory	This is the unit id. It consists of a 1 to 8 octet right justified case-sensitive ASCII field which uniquely identifies the unit. This ID is displayed on the L…
1.3.6.1.4.1.485.3.1.3.2	ScalarnmsSerialSpeed	read-only	mandatory	The async serial port speed for NMS console port. The speed is expressed in bits per second (i.e. 9.6 Kbps is represented as 96 decimal). Currently supported s…
1.3.6.1.4.1.485.3.1.3.3	ScalarserialPortLogoffTimer	read-only	mandatory	Units are minutes. Default value is 0, indicating that no timer is active.
1.3.6.1.4.1.485.3.1.3.4	ScalarcallRetryTimer	read-only	mandatory	The call retry timer (a.k.a Session Retry Timer). The number of seconds to wait before trying to retry a failed connection attempt. Currently supported values …
1.3.6.1.4.1.485.3.1.3.5	Scalarpassword	read-write	mandatory	The unit's password. This field indicates the system password used to log into the unit for operating the NMS interface. This field is a one to eight byte case…
1.3.6.1.4.1.485.3.1.3.6	ScalarconfigPassword	read-write	mandatory	The configuration password. This field indicates the password used to enter the configuration subsystem. This field is a one to eight byte case-sensitive left …
1.3.6.1.4.1.485.3.1.3.7	ScalardateTimeField	read-write	mandatory	The date and time. This field is stored as 6 bytes of BCD Data in the following order: Month: 0x01 - 0x12 Day: 0x01 - 0x31 Year: 0x00 - 0x99 Hour: 0x00 - 0x23 …
1.3.6.1.4.1.485.3.1.3.8	ScalarconfigId	read-only	mandatory	The configuration identifer. This field is the configuration ID assigned when a new configuration is activated. first time. It is assigned by the unit or a Syn…
1.3.6.1.4.1.485.3.1.3.9	ScalarinternalMacAddress	read-only	mandatory	Embedded conversion node MAC address. Applicable to Frame Node only.
1.3.6.1.4.1.485.3.1.3.10	ScalarinternalRingNumber	read-only	mandatory	Embedded conversion node ring number. This should be unique within the network. Applicable to Frame Node only.
1.3.6.1.4.1.485.3.1.3.11	ScalarinternalBridgeNumber	read-only	mandatory	Embedded conversion node bridge number. This parameter is currently not used. Applicable to Frame Node only.
1.3.6.1.4.1.485.3.1.3.12	ScalarinternalMacAddress2	read-only	mandatory	Optional second embedded conversion node MAC address. Applicable to Frame Node only.
1.3.6.1.4.1.485.3.1.3.13	ScalarinternalRingNumber2	read-only	mandatory	Optional second embedded conversion node ring number. This should be unique within the network. Applicable to Frame Node only.
1.3.6.1.4.1.485.3.1.3.14	ScalarassociatedPortNumber2	read-only	mandatory	Assigns the physical port number corresponding to the virtual port that the second embedded conversion node is associated with. Applicable to Frame Node only.
1.3.6.1.4.1.485.3.1.3.15	ScalarassociatedDLCI2	read-only	mandatory	Assigns the Frame Relay PVC number corresponding to the virtual port that the second embedded conversion node is associated with. Applicable to Frame Node only.
1.3.6.1.4.1.485.3.1.3.16	ScalarinternalMacAddress3	read-only	mandatory	Optional third embedded conversion node MAC address. Applicable to Frame Node only.
1.3.6.1.4.1.485.3.1.3.17	ScalarinternalRingNumber3	read-only	mandatory	Optional third embedded conversion node ring number. This should be unique within the network. Applicable to Frame Node only.
1.3.6.1.4.1.485.3.1.3.18	ScalarassociatedPortNumber3	read-only	mandatory	Assigns the physical port number corresponding to the virtual port that the third embedded conversion node is associated with. Applicable to Frame Node only.
1.3.6.1.4.1.485.3.1.3.19	ScalarassociatedDLCI3	read-only	mandatory	Assigns the Frame Relay PVC number corresponding to the virtual port that the third embedded conversion node is associated with. Applicable to Frame Node only.
1.3.6.1.4.1.485.3.1.3.20	ScalarinternalMacAddress4	read-only	mandatory	Optional forth embedded conversion node MAC address. Applicable to Frame Node only.
1.3.6.1.4.1.485.3.1.3.21	ScalarinternalRingNumber4	read-only	mandatory	Optional forth embedded conversion node ring number. This should be unique within the network. Applicable to Frame Node only.
1.3.6.1.4.1.485.3.1.3.22	ScalarassociatedPortNumber4	read-only	mandatory	Assigns the physical port number corresponding to the virtual port that the forth embedded conversion node is associated with. Applicable to Frame Node only.
1.3.6.1.4.1.485.3.1.3.23	ScalarassociatedDLCI4	read-only	mandatory	Assigns the Frame Relay PVC number corresponding to the virtual port that the forth embedded conversion node is associated with. Applicable to Frame Node only.
1.3.6.1.4.1.485.3.1.3.24	ScalaripInactivityTimer	read-only	mandatory	This timer is used for IP/SNMP over X25 support. It is the inactivity timer for an IP connection. If there is no activity for an IP session for the time this f…
1.3.6.1.4.1.485.3.1.3.25	ScalarexcessBurstGovernor	read-only	mandatory	This parameter configuration determines whether the FrameNode should limit the throughput on a per PVC basis to the configured Excess Burst Size (in the excess…
1.3.6.1.4.1.485.3.1.3.26	ScalarmeasurementPeriod	read-only	mandatory	This parameter specifies the time period for calculating Excess Burst for Frame Relay ports. The range of this parameter is 1 second to 5 seconds. Default is 1…
1.3.6.1.4.1.485.3.1.3.27	ScalarmarkDEBit	read-only	mandatory	This parameter specifies whether the FrameNode marks frames with the DE bit. The range of this parameter is YES or NO. Default is YES. If the parameter is set …
1.3.6.1.4.1.485.3.1.4	NodeunitStatisticsGroup
1.3.6.1.4.1.485.3.1.4.1	ScalarnumberSamples	read-only	mandatory	The number of internal system level samples performed. Samples are taken every 10th of a second.
1.3.6.1.4.1.485.3.1.4.2	ScalarsystemBufferFreeCounts	read-only	mandatory	The average number of system buffers free in the system during the system sample period. The number of available buffers varies by system type and configuratio…
1.3.6.1.4.1.485.3.1.4.3	ScalarcpuIdleSumCounts	read-only	mandatory	The main processor average idle sum count. This is the average number of times the idle counter was incremented over the sampling period divided by 1000. This …
1.3.6.1.4.1.485.3.2	NodenodeNetViewPUGroup
1.3.6.1.4.1.485.3.2.1	NodenetViewPUStatusGroup
1.3.6.1.4.1.485.3.2.1.1	ScalarnetviewConnectionStatus	read-only	mandatory	The status of the Primary Netview Connection.
1.3.6.1.4.1.485.3.2.1.2	ScalarnetviewLastClearCode	read-only	mandatory	A two octet field indicating the Last Clearing Cause and Diagnostic Field of the last failed primary NetView connection attempt (a.k.a. call attempt) or Netvie…
1.3.6.1.4.1.485.3.2.1.3	ScalarnetviewAltConnectionStatus	read-only	mandatory	The status of the alternate Netview Connection
1.3.6.1.4.1.485.3.2.1.4	ScalarnetviewAltLastClearCode	read-only	mandatory	A two octet field indicating the Last Clearing Cause and Diagnostic Field of the last failed alternate NetView connection attempt (a.k.a. call attempt) or Netv…
1.3.6.1.4.1.485.3.2.1.5	ScalarnetviewConnectionAttemptCount	read-only	mandatory	The number of connection attempts performed on the Primary NetView PU. This count is set to zero at startup, and after every loss of an estabished session.
1.3.6.1.4.1.485.3.2.1.6	ScalarnetviewAltConnectionAttemptCount	read-only	mandatory	The number of connection attempts performed on the Alternate NetView PU. This count is set to zero at startup, and after every loss of an estabished session.
1.3.6.1.4.1.485.3.2.1.7	ScalarnetviewStatusIgnored	read-write	mandatory	This field is used for consolidating status of the unit. The status of this netview pu is not put into consideration when consolidating status of the unit if t…
1.3.6.1.4.1.485.3.2.1.8	ScalarnetviewStatusAcknowledged	read-write	mandatory	This field is used for consolidating status of the unit. When this field is set to yes, the unit will re-consolidate its status without putting the status of t…
1.3.6.1.4.1.485.3.2.1.9	ScalarnetviewAltStatusIgnored	read-write	mandatory	This field is used for consolidating status of the unit. The status of this netview pu is not put into consideration when consolidating status of the unit if t…
1.3.6.1.4.1.485.3.2.1.10	ScalarnetviewAltStatusAcknowledged	read-write	mandatory	This field is used for consolidating status of the unit. When this field is set to yes, the unit will re-consolidate its status without putting the status of t…
1.3.6.1.4.1.485.3.2.2	NodenetViewPUConfigGroup
1.3.6.1.4.1.485.3.2.2.1	ScalarnetviewPUXID	read-only	mandatory	Primary NetView PU XID. This field indicates the XID data to be sent to the host for establishing Netview Session. This field is a maximum four byte hexadecima…
1.3.6.1.4.1.485.3.2.2.2	ScalaralternateNetviewPUXID	read-only	mandatory	Alternate NetView PU XID. This field indicates the XID data to be sent to the host for establishing Netview Session. This field is a maximum four byte hexadeci…
1.3.6.1.4.1.485.3.2.2.3	ScalarnetviewConnectID	read-only	mandatory	The primary NetView PU connection ID. The default value is 0.
1.3.6.1.4.1.485.3.2.2.4	ScalaralternateNetviewConnectID	read-only	mandatory	The alternate NetView PU connection ID. The default value is 0.
1.3.6.1.4.1.485.3.2.2.5	ScalarnetviewSpecialConnect	read-only	mandatory	The primary NetView PU connection type. The default value is originate.
1.3.6.1.4.1.485.3.2.2.6	ScalaralternateNetviewSpecialConnect	read-only	mandatory	The alternate NetView PU connection type. The default value is originate.
1.3.6.1.4.1.485.3.3	NodenodeBridgeGroup
1.3.6.1.4.1.485.3.3.1	NodebridgeConfigGroup
1.3.6.1.4.1.485.3.3.1.1	ScalarbrEnableBridging	read-only	mandatory	This flag indicates if bridging is to be performed on this unit. Applicable to Frame Nodes only. The default value for this field is 'No'
1.3.6.1.4.1.485.3.3.1.2	ScalarbridgePriority	read-only	mandatory	Sometimes referred to as the ROOT id. Determines the priority component of the Bridge identifier used in determining the Root Bridge for a spanning tree networ…
1.3.6.1.4.1.485.3.3.1.3	ScalarbrMaxAge	read-only	mandatory	The time at which a configuration message is descarded. Units are in seconds. Default value is 10 seconds
1.3.6.1.4.1.485.3.3.1.4	ScalarbrHelloTimer	read-only	mandatory	The time interval between issuing configuration messages. Units are seconds. Default value is 2 seconds
1.3.6.1.4.1.485.3.3.1.5	ScalarbrFilterIPX	read-only	mandatory	If set to yes, all IPX frames are filtered (if bridge is enabled). Default is no.
1.3.6.1.4.1.485.3.3.1.6	ScalarbrFilterIP	read-only	mandatory	If set to yes, all IP frames are filtered (if bridging is enabled). Default is no.
1.3.6.1.4.1.485.3.3.1.7	ScalarbrFilterNetBIOS	read-only	mandatory	If set to yes, all NetBIOS frames are filtered (if bridging is enabled). Default is no.
1.3.6.1.4.1.485.3.3.1.8	ScalarbrFilterLLC2	read-only	mandatory	If set to yes, all LAN attached SNA LLC2 frames are filtered (if bridging is enabled). Default is no.
1.3.6.1.4.1.485.3.3.1.9	ScalarbrFilterSMAN	read-only	mandatory	If set to yes, all SyncManager LLC2 frames are filtered (if bridging is enabled). Default is no.
1.3.6.1.4.1.485.3.3.1.10	ScalarbrForwardOther	read-only	mandatory	If set to yes, all other frames are forwarded (if bridging is enabled). Default is No.
1.3.6.1.4.1.485.3.3.1.11	ScalarbrIPXtargetPort	read-only	mandatory	If IPX filtering is set to no, then this parameter defines a specific FR port to deliver IPX frames to. Used in conjunction with brIPXtargetDLCI. The valid ran…
1.3.6.1.4.1.485.3.3.1.12	ScalarbrIPXtargetDLCI	read-only	mandatory	If IPX filtering is set to no, then this parameter defines a specific FR DLCI to deliver IPX frames to. Used in conjunction with brIPXtargetPort. If the value …
1.3.6.1.4.1.485.3.3.1.13	ScalarbrIPtargetPort	read-only	mandatory	If IP filtering is set to no, then this parameter defines a specific FR port to deliver IP frames to. Used in conjunction with brIPtargetDLCI. The valid range …
1.3.6.1.4.1.485.3.3.1.14	ScalarbrIPtargetDLCI	read-only	mandatory	If IP filtering is set to no, then this parameter defines a specific FR DLCI to deliver IP frames to. Used in conjunction with brIPtargetPort. If the value of …
1.3.6.1.4.1.485.3.3.1.15	ScalarbrNetBIOStargetPort	read-only	mandatory	If NetBIOS filtering is set to no, then this parameter defines a specific FR port to deliver NetBIOS frames to. Used in conjunction with brNetBIOStargetDLCI. T…
1.3.6.1.4.1.485.3.3.1.16	ScalarbrNetBIOStargetDLCI	read-only	mandatory	If NetBIOS filtering is set to no, then this parameter defines a specific FR DLCI to deliver NetBIOS frames to. Used in conjunction with brNetBIOStargetPort. I…
1.3.6.1.4.1.485.3.3.1.17	ScalarbrLLC2targetPort	read-only	mandatory	If SNA LLC2 filtering is set to no, then this parameter defines a specific FR port to deliver LLC2 frames to. Used in conjunction with brLLC2targetDLCI. The va…
1.3.6.1.4.1.485.3.3.1.18	ScalarbrLLC2targetDLCI	read-only	mandatory	If SNA LLC2 filtering is set to no, then this parameter defines a specific FR DLCI to deliver LLC2 frames to. Used in conjunction with brLLC2targetPort. If the…
1.3.6.1.4.1.485.3.3.1.19	ScalarbrOthertargetPort	read-only	mandatory	If Other forwarding is set to yes, then this parameter defines a specific FR port to deliver Other frames to. Used in conjunction with brOthertargetDLCI. The v…
1.3.6.1.4.1.485.3.3.1.20	ScalarbrOthertargetDLCI	read-only	mandatory	If Other forwarding is set to yes, then this parameter defines a specific FR DLCI to deliver Other frames to. Used in conjunction with brOthertargetPort. If th…
1.3.6.1.4.1.485.3.3.1.21	ScalarbrSerialPriority	read-only	mandatory	This parameter defines the transmit priority for Frame Relay of serial attached port traffic.
1.3.6.1.4.1.485.3.3.1.22	ScalarbrTerminatedLLC2Priority	read-only	mandatory	This parameter defines the transmit priority for Frame Relay of terminated LLC2 traffic.
1.3.6.1.4.1.485.3.3.1.23	ScalarbrLLC2Priority	read-only	mandatory	This parameter defines the transmit priority for Frame Relay of SNA LLC2 traffic.
1.3.6.1.4.1.485.3.3.1.24	ScalarbrIPXPriority	read-only	mandatory	This parameter defines the transmit priority for Frame Relay of IPX traffic.
1.3.6.1.4.1.485.3.3.1.25	ScalarbrIPPriority	read-only	mandatory	This parameter defines the transmit priority for Frame Relay of IP traffic.
1.3.6.1.4.1.485.3.3.1.26	ScalarbrNetBIOSPriority	read-only	mandatory	This parameter defines the transmit priority for Frame Relay of NetBIOS traffic.
1.3.6.1.4.1.485.3.3.1.27	ScalarbrOtherPriority	read-only	mandatory	This parameter defines the transmit priority for Frame Relay of other traffic.
1.3.6.1.4.1.485.3.3.1.28	ScalarbrHighPriorityBandwidth	read-only	mandatory	This parameter defines the high priority bandwidth. The sum of high, medium, and low priority bandwidth cannot exceed 100. Default value is 40.
1.3.6.1.4.1.485.3.3.1.29	ScalarbrMediumPriorityBandwidth	read-only	mandatory	This parameter defines the medium priority bandwidth. The sum of high, medium, and low priority bandwidth cannot exceed 100. Default value is 30.
1.3.6.1.4.1.485.3.3.1.30	ScalarbrLowPriorityBandwidth	read-only	mandatory	This parameter defines the low priority bandwidth. The sum of high, medium, and low priority bandwidth cannot exceed 100. Default value is 20.
1.3.6.1.4.1.485.3.3.1.31	ScalarbrDelayTimer	read-only	mandatory	This field, expressed in seconds, specifies the maximum number of seconds a bridge frame can live in the unit. If a bridge frame stays in the unit longer than …
1.3.6.1.4.1.485.3.3.1.32	ScalarbrEnableIPXBridging	read-only	mandatory	This flag indicates if IPX bridging is to be performed on this unit. Applicable to Frame Nodes only. The default value for this field is 'Yes'
1.3.6.1.4.1.485.3.3.1.33	ScalarbrEnableIPBridging	read-only	mandatory	This flag indicates if IP bridging is to be performed on this unit. Applicable to Frame Nodes only. The default value for this field is 'Yes'
1.3.6.1.4.1.485.3.3.1.34	ScalarbrEnableNetBiosBridging	read-only	mandatory	This flag indicates if NetBios bridging is to be performed on this unit. Applicable to Frame Nodes only. The default value for this field is 'Yes'
1.3.6.1.4.1.485.3.3.1.35	ScalarbrEnableSNABridging	read-only	mandatory	This flag indicates if SNA bridging is to be performed on this unit. Applicable to Frame Nodes only. The default value for this field is 'Yes'
1.3.6.1.4.1.485.3.3.1.36	ScalarbrEnableSyncManBridging	read-only	mandatory	This flag indicates if Sync/Man bridging is to be performed on this unit. Applicable to Frame Nodes only. The default value for this field is 'Yes'
1.3.6.1.4.1.485.3.3.1.37	ScalarbrEnableOtherBridging	read-only	mandatory	This flag indicates if any other traffic bridging is to be performed on this unit. Applicable to Frame Nodes only. The default value for this field is 'No'
1.3.6.1.4.1.485.3.3.2	NodebridgeStatsGroup
1.3.6.1.4.1.485.3.3.2.1	TableipxStatsTable	not-accessible	mandatory	A table for reporting statistics for bridging.
1.3.6.1.4.1.485.3.3.2.1.1	RowipxStatsEntry	not-accessible	mandatory	An entry consisting of IPX bridging statistics for each bridge port.
1.3.6.1.4.1.485.3.3.2.1.1.1	ColumnipxStatsIndex	read-only	mandatory	The number that uniquely identifies this IPX bridge port.
1.3.6.1.4.1.485.3.3.2.1.1.2	ColumnipxRipRcvdFwdInterval	read-only	mandatory	Identifies the number of IPX RIP packets received on this port during the RIP forwarding interval. These packets were accepted by the port.
1.3.6.1.4.1.485.3.3.2.1.1.3	ColumnipxRipRcvdFiltInterval	read-only	mandatory	Identifies the number of IPX RIP packets received on this port during the RIP filtering interval. These packets were tossed by the port.
1.3.6.1.4.1.485.3.3.2.1.1.4	ColumnipxSapRcvdFwdInterval	read-only	mandatory	Identifies the number of IPX SAP packets received on this port during the SAP forwarding interval. These packets were accepted by the port.
1.3.6.1.4.1.485.3.3.2.1.1.5	ColumnipxSapRcvdFiltInterval	read-only	mandatory	Identifies the number of IPX SAP packets received on this port during the SAP filtering interval. These packets were tossed by the port.
1.3.6.1.4.1.485.3.4	NodenodeLANGroup
1.3.6.1.4.1.485.3.4.1	NodelanControlGroup
1.3.6.1.4.1.485.3.4.1.1	TablelanControlTable	not-accessible	mandatory	A table for controlling LAN ports and obtaining information.
1.3.6.1.4.1.485.3.4.1.1.1	RowlanControlEntry	not-accessible	mandatory	An entry consisting of port information for a particular LAN port.
1.3.6.1.4.1.485.3.4.1.1.1.1	ColumnlanControlIndex	read-only	mandatory	The number that uniquely identifies this LAN port. Currently only one LAN port per unit is supported.
1.3.6.1.4.1.485.3.4.1.1.1.2	ColumnlanControlType	read-only	mandatory	The LAN type. Token-Ring ports run the IEEE 802.5 protocol. Ethernet-type run the IEEE 802.3 and Ethernet Version 2. Other LAN protocols may be added in the fu…
1.3.6.1.4.1.485.3.4.1.1.1.3	ColumnlanStatus	read-write	mandatory	The status of the port. To change status of a port an enable, enable all or disable may be set. Valid Return status are enable(d), disable(d), or failed. Comma…
1.3.6.1.4.1.485.3.4.1.1.1.4	ColumnlanControlFailureCode	read-only	mandatory	This entry contains the failure codes if the associated LAN interface is in the failed state.
1.3.6.1.4.1.485.3.4.1.1.1.5	ColumnlanControlNAUName	read-only	mandatory	The NAU name of this port. The default value for this field is all blank (filled with ASCII space 0x20 characters).
1.3.6.1.4.1.485.3.4.1.1.1.6	ColumnlanStatusIgnored	read-write	mandatory	This field is used for consolidating status of the unit. The status of this LAN is not put into consideration when consolidating status of the unit if this fie…
1.3.6.1.4.1.485.3.4.1.1.1.7	ColumnlanStatusAcknowledged	read-write	mandatory	This field is used for consolidating status of the unit. When this field is set to yes, the unit will re-consolidate its status without putting the status of t…
1.3.6.1.4.1.485.3.4.2	NodelanTokenRingGroup
1.3.6.1.4.1.485.3.4.2.1	TablelanPortTable	not-accessible	mandatory	A table of LAN information.
1.3.6.1.4.1.485.3.4.2.1.1	RowlanPortEntry	not-accessible	mandatory	An entry consisting of port information for a particular LAN port.
1.3.6.1.4.1.485.3.4.2.1.1.1	ColumnlanPortIndex	read-only	mandatory	The port number that uniquely identifies this port. Currently only one LANtoken ring port per unit is supported.
1.3.6.1.4.1.485.3.4.2.1.1.2	ColumnlanPortType	read-only	mandatory	The LAN port type.
1.3.6.1.4.1.485.3.4.2.1.1.3	ColumnlanMACAddress	read-only	mandatory	The user configured LANtoken ring MAC address. If the address is set to 0 then the burned-in Address is used. This field contains a user configured address if …
1.3.6.1.4.1.485.3.4.2.1.1.4	ColumnlanPROMMACAddress	read-only	mandatory	The burned in MAC address. This is the MAC address assigned by the factory when the unit is shipped. If the User configured address is set to 0, then this will…
1.3.6.1.4.1.485.3.4.2.1.1.5	ColumnlanSpeed	read-only	mandatory	The LAN port speed in Megabits/second.
1.3.6.1.4.1.485.3.4.2.1.1.6	ColumnlanT1Timer	read-only	mandatory	The default LLC T1 timer value in seconds. T1 should be greater than T2 and less than Ti. Currently supported values are 1 to 25 seconds. The default value for…
1.3.6.1.4.1.485.3.4.2.1.1.7	ColumnlanT2Timer	read-only	mandatory	The default LLC T2 timer value in tenths of seconds. If configured for 0 then the T2 timer is disabled and an RR frame will be sent for every I frame received.…
1.3.6.1.4.1.485.3.4.2.1.1.8	ColumnlanTiTimer	read-only	mandatory	The default LLC Ti (inactivity) timer value in seconds. Ti should be greater than T1. Currently supported values are 2 to 50 seconds. The default value for thi…
1.3.6.1.4.1.485.3.4.2.1.1.9	ColumnlanRxWindowSize	read-only	mandatory	The default LLC receive window (N3) size. Note that this is not the same receive window as defined in IEEE 802.2 LLC. This is N3 which is the number of I frame…
1.3.6.1.4.1.485.3.4.2.1.1.10	ColumnlanTxWindowSize	read-only	mandatory	The defalut LLC transmit window size. Current allowable values are 1-15. The default value for this field is 7.
1.3.6.1.4.1.485.3.4.2.1.1.11	ColumnlanMaxRetries	read-only	mandatory	The default LLC maximum number of retries (N2 value). Current allowable values are 1-99. The default value for this field is 3.
1.3.6.1.4.1.485.3.4.2.1.1.12	ColumnlanRingNumber	read-only	mandatory	802.5 bridging parameter. This variable returns a value of 0, if it is not defined. This value is configured in hex from 0 to FFF. This value is not applicable…
1.3.6.1.4.1.485.3.4.2.1.1.13	ColumnlanBridgeNumber	read-only	mandatory	802.5 bridging parameter. The default value for this field is 1. This value is not applicable to Ethernet.
1.3.6.1.4.1.485.3.4.2.1.1.14	ColumnlanEthernetFrameFormat	read-only	mandatory	The Ethernet frame format used on this LAN. The default value for this field is 802.3. Not used if Token Ring, and 1 is returned.
1.3.6.1.4.1.485.3.4.2.1.1.15	ColumnlanSendLocalTest	read-only	mandatory	This port's send local test option. Identifies whether a test frame should be sent on the local ring to discover a destination MAC address. If all destinations…
1.3.6.1.4.1.485.3.4.2.1.1.16	ColumnlanBroadcastType	read-only	mandatory	This port's broadcast type. Not used if Ethernet. Types are: none, all-routes, and single-route. Identifies the form of a broadcast test frame sent to discover…
1.3.6.1.4.1.485.3.4.2.1.1.17	ColumnlanIPAddress	read-only	mandatory	This is the IP Address of this interface.
1.3.6.1.4.1.485.3.4.2.1.1.18	ColumnlanNetworkMask	read-only	mandatory	This is the network mask to be used on this interface.
1.3.6.1.4.1.485.3.4.2.1.1.19	ColumnlanDefaultGateway	read-only	mandatory	Default gateway address to be used when sending responses on this interface.
1.3.6.1.4.1.485.3.4.2.1.1.20	ColumnlanNAUName	read-only	mandatory	The NAU name of this port. The default value for this field is all blank (filled with ASCII space 0x20 characters).
1.3.6.1.4.1.485.3.4.2.1.1.21	ColumnlanInterfaceType	read-only	mandatory	This port's physical interface type. Only used if Ethernet. The default for this field is utp. Not used if Token Ring, and 1 is returned.
1.3.6.1.4.1.485.3.4.2.1.1.22	ColumnlanIPEthernetFrameType	read-only	mandatory	The IP Ethernet frame format used on this LAN for IP frames. The default value for this field is 802.3. Not used if Token Ring, and 1 is returned.
1.3.6.1.4.1.485.3.4.2.1.1.23	ColumnlanInitState	read-only	mandatory	The initial state of the LAN port. If configured for 'in-service', then the LAN port will be brougt up automattically when the unit is powered up. If configure…
1.3.6.1.4.1.485.3.4.2.1.1.24	ColumnlanSecondDefaultGateway	read-only	mandatory	Second Default gateway address to be used when sending responses on this interface.
1.3.6.1.4.1.485.3.4.2.1.1.25	ColumnlanRIPUpdtTimer	read-only	mandatory	Defines frequency at which the RIP packets are sent over this interface. The range of this parameter is from 10 seconds to 180 seconds. A value of 0 implies no…
1.3.6.1.4.1.485.3.4.2.1.1.26	ColumnlanRIPAge	read-only	mandatory	Defines frequency at which the learned RIP entries are removed if not corresponding RIP update is received. The range of this parameter is from 40 seconds to 5…
1.3.6.1.4.1.485.3.4.2.1.1.27	ColumnlanSAPUpdtTimer	read-only	mandatory	Defines frequency at which the SAP packets are sent over this interface. The range of this parameter is from 10 seconds to 180 seconds. A value of 0 implies th…
1.3.6.1.4.1.485.3.4.2.1.1.28	ColumnlanSAPAge	read-only	mandatory	Defines frequency at which the learned SAP entries are removed if not corresponding SAP update is received. The range of this parameter is from 40 seconds to 7…
1.3.6.1.4.1.485.3.4.2.1.1.29	ColumnlanRSM	read-only	mandatory	The Routing Summary Information parameter indicates whether the routing summary information should be generated in the RIP on that interface. If RSM is set to …
1.3.6.1.4.1.485.3.5	NodenodeLineGroup
1.3.6.1.4.1.485.3.5.1	NodelineControlGroup
1.3.6.1.4.1.485.3.5.1.1	TablelineControlTable	not-accessible	mandatory	A table for controlling lines and obtaining information.
1.3.6.1.4.1.485.3.5.1.1.1	RowlineControlEntry	not-accessible	mandatory	An entry consisting of port information for a particular port.
1.3.6.1.4.1.485.3.5.1.1.1.1	ColumnlineControlIndex	read-only	mandatory	The port number that uniquely identifies this port.
1.3.6.1.4.1.485.3.5.1.1.1.2	ColumnlineControlType	read-only	mandatory	The port type. TSDLC (Terminal SDLC) ports emulate a Host and poll the downstream PUs (e.g. 3274 or 3174 SDLC/SNA controllers). HSDLC ports (Host SDLC) ports e…
1.3.6.1.4.1.485.3.5.1.1.1.3	ColumnlineStatus	read-write	mandatory	The status of the port. To change status of a port an enable, enable all or disable may be set. Valid Return status are enable(d), disable(d), or failed. When …
1.3.6.1.4.1.485.3.5.1.1.1.4	ColumnlineControlFailureCode	read-only	mandatory	This entry contains the failure codes if the associated port interface is in the failed state.
1.3.6.1.4.1.485.3.5.1.1.1.5	ColumnlineControlNAUName	read-only	mandatory	The NAU name of this port. The default value for this field is all blank (filled with ASCII space 0x20 characters).
1.3.6.1.4.1.485.3.5.1.1.1.6	ColumnlineStatusIgnored	read-write	mandatory	This field is used for consolidating status of the unit. The status of this line is not put into consideration when consolidating status of the unit if this fi…
1.3.6.1.4.1.485.3.5.1.1.1.7	ColumnlineStatusAcknowledged	read-write	mandatory	This field is used for consolidating status of the unit. When this field is set to yes, the unit will re-consolidate its status without putting the status of t…
1.3.6.1.4.1.485.3.5.1.1.1.8	ColumnloopbackTest	read-write	mandatory	Loopback Test can be supported on both DSU/CSU and ISDN. Loopback can be local, Network, or Remote. Local loopback means outgoing serial data is looped back to…
1.3.6.1.4.1.485.3.5.2	NodelinePhysicalGroup
1.3.6.1.4.1.485.3.5.2.1	TablelinePhysicalTable	not-accessible	mandatory	A table for obtaining physical signal status information.
1.3.6.1.4.1.485.3.5.2.1.1	RowlinePhysicalEntry	not-accessible	mandatory	An entry consisting of port information for a particular port.
1.3.6.1.4.1.485.3.5.2.1.1.1	ColumnlinePhysicalIndex	read-only	mandatory	The port number that uniquely identifies this port.
1.3.6.1.4.1.485.3.5.2.1.1.2	ColumnlinePhysicalType	read-only	mandatory	The port type. TSDLC (Terminal SDLC) ports emulate a Host and poll the downstream PUs (e.g. 3274 or 3174 SDLC/SNA controllers). HSDLC ports (Host SDLC) ports e…
1.3.6.1.4.1.485.3.5.2.1.1.3	ColumnlineEIAStatus	read-only	mandatory	A port's current control signal status. All SDLC ports have the ability to read the current status of RS-232 or equivalent control signals. The value returned …
1.3.6.1.4.1.485.3.5.2.1.1.4	ColumnlineQualityFrameCount	read-only	mandatory	This entry contains the number of frames received. For every 255 incoming frames, a trap is generated by the unit if lineQualityCRCErrors or lineQualityAborts …
1.3.6.1.4.1.485.3.5.2.1.1.5	ColumnlineQualityCRCErrors	read-only	mandatory	This entry contains the number of frames with CRC errors. For every 255 incoming frames, a trap is generated by the unit if lineQualityCRCErrors or lineQuality…
1.3.6.1.4.1.485.3.5.2.1.1.6	ColumnlineQualityAborts	read-only	mandatory	This entry contains the number of aborts received. For every 255 incoming frames, a trap is generated by the unit if lineQualityCRCErrors or lineQualityAborts …
1.3.6.1.4.1.485.3.5.2.1.1.7	ColumnlineInterfaceType	read-only	mandatory	Report hardware Interface type of the line. For older systems, this interface is fixed per port. For universal ports, the Interface type if set via the cable.
1.3.6.1.4.1.485.3.5.2.1.1.8	ColumnlineCableType	read-only	mandatory	Returns not-applicable if the h/w does not support universal port configuration. Identifies the cable type connected to the port.
1.3.6.1.4.1.485.3.5.2.1.1.9	ColumnlineSwitchedConnection	read-only	mandatory	Identifies whether the line is connected over a switched backup facility or a dedicated facility to a frame relay network. This parameter is applicable to fram…
1.3.6.1.4.1.485.3.5.2.2	NodeisdnControlGroup
1.3.6.1.4.1.485.3.5.2.2.1	TableisdndeviceConfigTable	not-accessible	mandatory	A list of device entries.
1.3.6.1.4.1.485.3.5.2.2.1.1	RowisdndeviceConfigEntry	not-accessible	mandatory	This entry contains information about a given device. The entry is indexed by the port number, CU index, and device.
1.3.6.1.4.1.485.3.5.2.2.1.1.1	ColumnisdnLineIndex	read-only	mandatory	The port number for which the ISDN line is configured (line level).
1.3.6.1.4.1.485.3.5.2.2.1.1.2	ColumnserviceType	read-only	mandatory	Defines the service type of the ISDN WAN port.
1.3.6.1.4.1.485.3.5.2.2.1.1.3	ColumnisdnSpeed	read-only	mandatory	The ports speed in 100 bits per second. The default value is 56000 bits per second.
1.3.6.1.4.1.485.3.5.2.2.1.1.4	ColumnconnectionTimeOut	read-only	mandatory	Defines the time to wait after sensing disruption before declaring failure. The range is 0 to 255 seconds. The default value is 12 seconds.
1.3.6.1.4.1.485.3.5.2.2.1.1.5	ColumnnosConnectAttempts	read-only	mandatory	Defines the number or re-dial attempts before fail to connect. The range is 0 to 255. The default value is 1.
1.3.6.1.4.1.485.3.5.2.2.1.1.6	ColumnfarEndNumberType	read-only	mandatory	One byte field that defines the called number type.
1.3.6.1.4.1.485.3.5.2.2.1.1.7	ColumnfarEndNumberPlan	read-only	mandatory	One byte field that defines the called number Plan.
1.3.6.1.4.1.485.3.5.2.2.1.1.8	ColumnfarEndNumber	read-only	mandatory	One byte field that defines the called number.
1.3.6.1.4.1.485.3.5.2.2.1.1.9	ColumnlocalNumberType	read-only	mandatory	One byte field that defines the local number type.
1.3.6.1.4.1.485.3.5.2.2.1.1.10	ColumnlocalNumberPlan	read-only	mandatory	One byte field that defines the local number Plan.
1.3.6.1.4.1.485.3.5.2.2.1.1.11	ColumnlocalNumber	read-only	mandatory	One byte field that defines the local number.
1.3.6.1.4.1.485.3.5.2.2.1.1.12	Columnspid	read-only	mandatory	SPID is a zero-terminated ASCII string with a minium length of 0 and a maximum length of 20.
1.3.6.1.4.1.485.3.5.2.2.2	TableisdndeviceStatsTable	not-accessible	mandatory	A list of device entries.
1.3.6.1.4.1.485.3.5.2.2.2.1	RowisdndeviceStatsEntry	not-accessible	mandatory	This entry contains information about a given device. The entry is indexed by the port number, CU index, and device.
1.3.6.1.4.1.485.3.5.2.2.2.1.1	ColumnisdnIndex	read-only	mandatory	The port number for which the ISDN line is configured (line level).
1.3.6.1.4.1.485.3.5.2.2.2.1.2	ColumnchannelID	read-only	mandatory	The port number for which the ISDN line is configured (line level).
1.3.6.1.4.1.485.3.5.2.2.2.1.3	ColumnkbytesTransmitted	read-only	mandatory	This entry contains the number of bytes transmited.
1.3.6.1.4.1.485.3.5.2.2.2.1.4	ColumnkbytesReceived	read-only	mandatory	This entry contains the number of bytes received.
1.3.6.1.4.1.485.3.5.2.2.2.1.5	ColumnpacketsTransmitted	read-only	mandatory	This entry contains the number of packets transmited.
1.3.6.1.4.1.485.3.5.2.2.2.1.6	ColumnpacketsReceived	read-only	mandatory	This entry contains the number of packets received.
1.3.6.1.4.1.485.3.5.2.2.2.1.7	ColumnisdnloopbackbytesTransmitted	read-only	mandatory	This entry contains the number of bytes transmited.
1.3.6.1.4.1.485.3.5.2.2.2.1.8	ColumnisdnloopbackbytesReceived	read-only	mandatory	This entry contains the number of bytes received.
1.3.6.1.4.1.485.3.5.2.2.2.1.9	ColumnisdnCRCErrors	read-only	mandatory	This entry contains the number of frames with CRC errors.
1.3.6.1.4.1.485.3.5.2.3	NodedsucsuControlGroup
1.3.6.1.4.1.485.3.5.2.3.1	TabledsucsudeviceConfigTable	not-accessible	mandatory	A list of device entries.
1.3.6.1.4.1.485.3.5.2.3.1.1	RowdsucsudeviceConfigEntry	not-accessible	mandatory	This entry contains information about a given device. The entry is indexed by the port number, CU index, and device.
1.3.6.1.4.1.485.3.5.2.3.1.1.1	ColumndsucsuLineNumber	read-only	mandatory	The port number for which the DsuCsu line is configured (line level).
1.3.6.1.4.1.485.3.5.2.3.1.1.2	ColumndsucsuType	read-only	mandatory	Defines the service type of the DSU/CSU port.
1.3.6.1.4.1.485.3.5.2.3.1.1.3	ColumndsucsuClocking	read-only	mandatory	Clocking source for this port. Setting 'internal' will cause the port to emulate a physical DCE, and setting external will cause the port to emulate a physical…
1.3.6.1.4.1.485.3.5.2.3.1.1.4	ColumndsucsuSpeed	read-only	mandatory	The ports speed in 100 bits per second. The default value is 56000 bits per second.
1.3.6.1.4.1.485.3.5.2.3.2	TabledsucsudeviceStatsTable	not-accessible	mandatory	A list of device entries.
1.3.6.1.4.1.485.3.5.2.3.2.1	RowdsucsudeviceStatsEntry	not-accessible	mandatory	This entry contains information about a given device. The entry is indexed by the port number, CU index, and device.
1.3.6.1.4.1.485.3.5.2.3.2.1.1	ColumndsucsuLine	read-only	mandatory	The port number for which the DsuCsu line is configured (line level).
1.3.6.1.4.1.485.3.5.2.3.2.1.2	ColumndsucsuloopbackbytesTransmitted	read-only	mandatory	This entry contains the number of bytes transmited.
1.3.6.1.4.1.485.3.5.2.3.2.1.3	ColumndsucsuloopbackbytesReceived	read-only	mandatory	This entry contains the number of bytes received.
1.3.6.1.4.1.485.3.5.3	NodelineSDLCGroup
1.3.6.1.4.1.485.3.5.3.1	TablesdlcConfigTable	not-accessible	mandatory	A table of SDLC information.
1.3.6.1.4.1.485.3.5.3.1.1	RowsdlcConfigEntry	not-accessible	mandatory	An entry consisting of port information for a particular SDLC port.
1.3.6.1.4.1.485.3.5.3.1.1.1	ColumnsdlcConfigPortIndex	read-only	mandatory	The port number that uniquely identifies this port. Current supported SDLC numbers are 1-4.
1.3.6.1.4.1.485.3.5.3.1.1.2	ColumnsdlcConfigType	read-only	mandatory	The port type. TSDLC (Terminal SDLC) ports emulate a Host and poll the downstream PUs (e.g. 3274 or 3174 SDLC/SNA controllers). HSDLC ports (Host SDLC) ports e…
1.3.6.1.4.1.485.3.5.3.1.1.3	ColumnsdlcInitState	read-only	mandatory	The initial state of the SDLC port. If configured for 'in-service', then the SDLC port will be brougt up automattically when the unit is powered up. If configu…
1.3.6.1.4.1.485.3.5.3.1.1.4	ColumnsdlcCarrier	read-only	mandatory	This field indicates whether Carrier (a.k.a. CD or DCD, RS-232 pin 8) is constant or switched for DCE devices (internally clocked), or Request To Send (a.k.a. …
1.3.6.1.4.1.485.3.5.3.1.1.5	ColumnsdlcClocking	read-only	mandatory	Clocking source for this port. Setting 'internal' will cause the port to emulate a physical DCE, and setting external will cause the port to emulate a physical…
1.3.6.1.4.1.485.3.5.3.1.1.6	ColumnsdlcSpeed	read-only	mandatory	The ports speed in 100 bits per second. The default value is 9600 bits per second. Speeds higher than 19200 are not supported on RS-232 ports units (must be V.…
1.3.6.1.4.1.485.3.5.3.1.1.7	ColumnsdlcPause	read-only	mandatory	This parameter defines the amount of time between polls in 1/100 second (10 millisecond) intervals. If set to zero then the port will poll the PUs as fast as p…
1.3.6.1.4.1.485.3.5.3.1.1.8	ColumnsdlcNRZI	read-only	mandatory	This parameter indicates whether the port is configured for NRZI (yes) or NRZ (no) bit encoding. The default value is 'No' (NRZ encoding selected).
1.3.6.1.4.1.485.3.5.3.1.1.9	ColumnsdlcT1Timer	read-only	mandatory	The SDLC T1 timer value in 20ths of a second. The default value is 20 (1 second). This field is not applicable to Host ports. It returns a dummy value.
1.3.6.1.4.1.485.3.5.3.1.1.10	ColumnsdlcSlowPollTimer	read-only	mandatory	The slow poll timer value in 20ths of a second. The slow poll timer is the amount of time to wait to contact (send SNRM) failed PUs. The default value for this…
1.3.6.1.4.1.485.3.5.3.1.1.11	ColumnsdlcMaxRetries	read-only	mandatory	The maximum number of retries (N2 value) before failing a PU. The default value for this field is 3. This field is not applicable to Host ports. It returns a d…
1.3.6.1.4.1.485.3.5.3.1.1.12	ColumnsdlcNAUName	read-only	mandatory	The NAU name of this port. The default value for this field is all blank (filled with ASCII space 0x20 characters).
1.3.6.1.4.1.485.3.5.3.1.1.13	ColumnsdlcMultiFlagInsertion	read-only	mandatory	This parameter indicates whether the port is configured to send multiple interframe flags. The default value is 'No' (single flags).
1.3.6.1.4.1.485.3.5.3.1.1.14	ColumnsdlcCTS	read-only	mandatory	Defines whether CTS is an input signal used to determine the port status. This parameter is applicable if clocking is set to external. For internal clocking th…
1.3.6.1.4.1.485.3.5.3.1.1.15	ColumnsdlcDCD	read-only	mandatory	Defines whether DCD is required as input signal or ignored. This parameter is applicable if the clocking is set to external. For internal clocking the paramete…
1.3.6.1.4.1.485.3.5.3.1.1.16	ColumnsdlcDSR	read-only	mandatory	Defines whether DSR is required as input signal or ignored. This parameter is applicable if the clocking is set to external. For internal clocking the paramete…
1.3.6.1.4.1.485.3.5.3.1.1.17	ColumnsdlcDTR	read-only	mandatory	Defines whether DTR is required as input signal or ignored. This parameter is applicable if the clocking is set to internal. For external clocking the paramete…
1.3.6.1.4.1.485.3.5.3.1.1.18	ColumnsdlcRTS	read-only	mandatory	Defines whether RTS is an input signal to determine the port status. This parameter is applicable if the clocking is set to internal. For external clocking the…
1.3.6.1.4.1.485.3.5.3.1.1.19	ColumnsdlcReturnClock	read-only	mandatory	Defines whether Return Clock (SCTE) is available as input signal or ignored. This parameter is applicable if the clocking is set to internal. For external cloc…
1.3.6.1.4.1.485.3.5.3.2	TablesdlcStatsTable	not-accessible	mandatory	A table of SDLC information.
1.3.6.1.4.1.485.3.5.3.2.1	RowsdlcStatsEntry	not-accessible	mandatory	An entry consisting of port information for a particular SDLC port.
1.3.6.1.4.1.485.3.5.3.2.1.1	ColumnsdlcStatsPortIndex	read-only	mandatory	The port number that uniquely identifies this SDLC port. Current supported numbers on are 1-4.
1.3.6.1.4.1.485.3.5.3.2.1.2	ColumnsdlcPortType	read-only	mandatory	The port type. TSDLC (Terminal SDLC) ports emulate a Host and poll the downstream PUs (e.g. 3274 or 3174 SDLC/SNA controllers). HSDLC ports (Host SDLC) ports e…
1.3.6.1.4.1.485.3.5.3.2.1.3	ColumnsdlcInOctets	read-only	mandatory	The number of bytes received.
1.3.6.1.4.1.485.3.5.3.2.1.4	ColumnsdlcOutOctets	read-only	mandatory	The number of bytes sent.
1.3.6.1.4.1.485.3.5.3.2.1.5	ColumnsdlcInFrames	read-only	mandatory	The number of I-frames received.
1.3.6.1.4.1.485.3.5.3.2.1.6	ColumnsdlcOutFrames	read-only	mandatory	The number of I-frames sent.
1.3.6.1.4.1.485.3.5.3.2.1.7	ColumnsdlcOverruns	read-only	mandatory	The number of overruns.
1.3.6.1.4.1.485.3.5.3.2.1.8	ColumnsdlcCRCErrors	read-only	mandatory	The number of CRC errors.
1.3.6.1.4.1.485.3.5.3.2.1.9	ColumnsdlcRecvAborts	read-only	mandatory	The number of aborts received.
1.3.6.1.4.1.485.3.5.3.2.1.10	Columnsdlcpollrsptimeouts	read-only	mandatory	The number of poll response timeouts.
1.3.6.1.4.1.485.3.5.3.2.1.11	Columnsdlciframetrans	read-only	mandatory	The number of i-frame re-transmissions.
1.3.6.1.4.1.485.3.5.4	NodelineBisyncGroup
1.3.6.1.4.1.485.3.5.4.1	TablebisyncConfigTable	not-accessible	mandatory	A table of Bisync port information.
1.3.6.1.4.1.485.3.5.4.1.1	RowbisyncConfigEntry	not-accessible	mandatory	An entry consisting of port information for a particular Bisync port.
1.3.6.1.4.1.485.3.5.4.1.1.1	ColumnbisyncConfigPortIndex	read-only	mandatory	The port number that uniquely identifies this port. Current supported Bisync numbers are 1-4.
1.3.6.1.4.1.485.3.5.4.1.1.2	ColumnbisyncConfigType	read-only	mandatory	The port type. TBSC (Terminal Bisync) ports emulate a Host and polls the downstream controllers). HBSC ports (Host Bisync) ports emulate a line with Terminal C…
1.3.6.1.4.1.485.3.5.4.1.1.3	ColumnbisyncNAUName	read-only	mandatory	The NAU name of this port. The default value for this field is all blank (filled with ASCII space 0x20 characters).
1.3.6.1.4.1.485.3.5.4.1.1.4	ColumnbisyncInitState	read-only	mandatory	The initial state of the Bisync port. If configured for 'in-service', then the Bisync port will be brougt up automattically when the unit is powered up. If con…
1.3.6.1.4.1.485.3.5.4.1.1.5	ColumnbisyncCarrier	read-only	mandatory	This field indicates whether Carrier (a.k.a. CD or DCD, RS-232 pin 8) is constant or switched for DCE devices (internally clocked), or Request To Send (a.k.a. …
1.3.6.1.4.1.485.3.5.4.1.1.6	ColumnbisyncClocking	read-only	mandatory	Clocking source for this port. Setting 'internal' will cause the port to emulate a physical DCE, and setting external will cause the port to emulate a physical…
1.3.6.1.4.1.485.3.5.4.1.1.7	ColumnbisyncSpeed	read-only	mandatory	The ports speed in bits per second. The default value is 9600 bits per second. Speeds higher than 64000 are not supported.
1.3.6.1.4.1.485.3.5.4.1.1.8	ColumnbisyncPause	read-only	mandatory	This parameter defines the amount of time between polls in 1/100 second (10 millisecond) intervals. If set to zero then the port will poll the CUs as fast as p…
1.3.6.1.4.1.485.3.5.4.1.1.9	ColumnbisyncReplyTimer	read-only	mandatory	The time to wait for a response in seconds. The default value for this field is 3 seconds.
1.3.6.1.4.1.485.3.5.4.1.1.10	ColumnbisyncRetries	read-only	mandatory	The maximum number of retries (N2 value) before failing a CU. The default value for this field is 5.
1.3.6.1.4.1.485.3.5.4.1.1.11	ColumnbisyncSlowpollTimer	read-only	mandatory	The time to wait in seconds before attempting a slowpoll. The default value for this field is 30 seconds.
1.3.6.1.4.1.485.3.5.4.1.1.12	ColumnbisyncSessTerm	read-only	mandatory	The type of session termination used. Only applies to Host BSC ports.
1.3.6.1.4.1.485.3.5.4.1.1.13	ColumnbisyncIBS	read-only	mandatory	Some of non IBM 3270 BSC controllers can not handle ESC character but IBM 3270 BSC implementation requires ESC character. A new configuration parameter for Ter…
1.3.6.1.4.1.485.3.5.4.1.1.14	ColumnbisyncCTS	read-only	mandatory	Defines whether CTS is an input signal used to determine the port status. This parameter is applicable if clocking is set to external. For internal clocking th…
1.3.6.1.4.1.485.3.5.4.1.1.15	ColumnbisyncDCD	read-only	mandatory	Defines whether DCD is required as input signal or ignored. This parameter is applicable if the clocking is set to external. For internal clocking the paramete…
1.3.6.1.4.1.485.3.5.4.1.1.16	ColumnbisyncDSR	read-only	mandatory	Defines whether DSR is required as input signal or ignored. This parameter is applicable if the clocking is set to external. For internal clocking the paramete…
1.3.6.1.4.1.485.3.5.4.1.1.17	ColumnbisyncDTR	read-only	mandatory	Defines whether DTR is required as input signal or ignored. This parameter is applicable if the clocking is set to internal. For external clocking the paramete…
1.3.6.1.4.1.485.3.5.4.1.1.18	ColumnbisyncRTS	read-only	mandatory	Defines whether RTS is an input signal to determine the port status. This parameter is applicable if the clocking is set to internal. For external clocking the…
1.3.6.1.4.1.485.3.5.4.1.1.19	ColumnbisyncReturnClock	read-only	mandatory	Defines whether Return Clock (SCTE) is available as input signal or ignored. This parameter is applicable if the clocking is set to internal. For external cloc…
1.3.6.1.4.1.485.3.5.4.2	TablebisyncStatsTable	not-accessible	mandatory	A table of Bisync information.
1.3.6.1.4.1.485.3.5.4.2.1	RowbisyncStatsEntry	not-accessible	mandatory	An entry consisting of port information for a particular Bisync port.
1.3.6.1.4.1.485.3.5.4.2.1.1	ColumnbisyncStatsPortIndex	read-only	mandatory	The port number that uniquely identifies this Bisync port. Current supported numbers are 1-4.
1.3.6.1.4.1.485.3.5.4.2.1.2	ColumnbisyncPortType	read-only	mandatory	The port type. TBSC (Terminal Bisync) ports emulate a Host and poll the downstream controllers). HBSC ports (Host Bisync) ports emulate a line with Terminal Co…
1.3.6.1.4.1.485.3.5.4.2.1.3	ColumnbisyncInOctets	read-only	mandatory	The number of bytes received.
1.3.6.1.4.1.485.3.5.4.2.1.4	ColumnbisyncOutOctets	read-only	mandatory	The number of bytes sent.
1.3.6.1.4.1.485.3.5.4.2.1.5	ColumnbisyncOverruns	read-only	mandatory	The number of receiver overruns.
1.3.6.1.4.1.485.3.5.4.2.1.6	ColumnbisyncCRCErrors	read-only	mandatory	The number of receive frame CRC errors.
1.3.6.1.4.1.485.3.5.4.2.1.7	ColumnbisyncRcvTimeout	read-only	mandatory	The number of receive timeout.
1.3.6.1.4.1.485.3.5.4.2.1.8	ColumnbisyncXmtTimeout	read-only	mandatory	The number of transmit timeout.
1.3.6.1.4.1.485.3.5.5	NodelineFrameRelayGroup
1.3.6.1.4.1.485.3.5.5.1	TableframeRelayConfigTable	not-accessible	mandatory	A table of Sync product Frame Relay information.
1.3.6.1.4.1.485.3.5.5.1.1	RowframeRelayConfigEntry	not-accessible	mandatory	An entry consisting of port information for a particular Sync product Frame Relay port.
1.3.6.1.4.1.485.3.5.5.1.1.1	ColumnframeRelayConfigPortIndex	read-only	mandatory	The port number that uniquely identifies this port.
1.3.6.1.4.1.485.3.5.5.1.1.2	ColumnframeRelayPortType	read-only	mandatory	The Frame Relay port type.
1.3.6.1.4.1.485.3.5.5.1.1.3	ColumnframeRelayInitState	read-only	mandatory	The initial state of the Frame Relay port. If configured for 'in-service', then the Frame Relay port will be brougt up automatically when the unit is powered u…
1.3.6.1.4.1.485.3.5.5.1.1.4	ColumnframeRelayClocking	read-only	mandatory	Clocking source for this port. Setting 'internal' will cause the port to emulate a physical DCE, and setting external will cause the port to emulate a physical…
1.3.6.1.4.1.485.3.5.5.1.1.5	ColumnframeRelaySpeed	read-only	mandatory	The ports speed in bits per second. The default value is 9600 bits per second. Speeds higher than 19200 are not supported on RS-232 port Sync products (must be…
1.3.6.1.4.1.485.3.5.5.1.1.6	ColumnframeRelayLocalManagementProtocol	read-only	mandatory	The ports management protocol type. Annex D = ANSI T1.617 Annex D LMI = Frame Relay Manufacturers LMI The default value is Annex D.
1.3.6.1.4.1.485.3.5.5.1.1.7	ColumnframeRelayLinkPollingTimer	read-only	mandatory	Measured in seconds, intervals of 5 T391 - Annex D nT1 - LMI The default value for this field is 5 seconds.
1.3.6.1.4.1.485.3.5.5.1.1.8	ColumnframeRelayFullStatusPollingCount	read-only	mandatory	The number of polls that a full status poll is issued. N391 - Annex D nT1 - LMI The default value for this field is 6.
1.3.6.1.4.1.485.3.5.5.1.1.9	ColumnframeRelayT1Timer	read-only	mandatory	The default LLC T1 timer value in seconds. T1 should be greater than T2 and less than Ti. Currently supported values are 1 to 25 seconds. The default value for…
1.3.6.1.4.1.485.3.5.5.1.1.10	ColumnframeRelayT2Timer	read-only	mandatory	The default LLC T2 timer value in tenths of seconds. If configured for 0 then the T2 timer is disabled and an RR frame will be sent for every I frame received.…
1.3.6.1.4.1.485.3.5.5.1.1.11	ColumnframeRelayTiTimer	read-only	mandatory	The default LLC Ti (inactivity) timer value in seconds. Ti should be greater than T1. Currently supported values are 2 to 50 seconds. The default value for thi…
1.3.6.1.4.1.485.3.5.5.1.1.12	ColumnframeRelayRxWindowSize	read-only	mandatory	The default LLC receive window (N3) size. Note that this is not the same receive window as defined in IEEE 802.2 LLC. This is N3 which is the number of I frame…
1.3.6.1.4.1.485.3.5.5.1.1.13	ColumnframeRelayTxWindowSize	read-only	mandatory	The defalut LLC transmit window size. Current allowable values are 1-7. The default value for this field is 7.
1.3.6.1.4.1.485.3.5.5.1.1.14	ColumnframeRelayMaxRetries	read-only	mandatory	The default LLC maximum number of retries (N2 value). The default value for this field is 15.
1.3.6.1.4.1.485.3.5.5.1.1.15	ColumnframeRelayNAUName	read-only	mandatory	The NAU name of this port. The default value for this field is all blank (filled with ASCII space 0x20 characters).
1.3.6.1.4.1.485.3.5.5.1.1.16	ColumnframeRelayVirtualMACAddress	read-only	mandatory	The F/R WAN is treated as a token ring. This address is used for communication with other bridges in the network.
1.3.6.1.4.1.485.3.5.5.1.1.17	ColumnframeRelayVirtualRingNumber	read-only	mandatory	The F/R WAN is treated as a token ring. This is the ring number for the F/R network to which the port is attached. It must be a unique ring number in the netwo…
1.3.6.1.4.1.485.3.5.5.1.1.18	ColumnframeRelayVirtualBridgeNumber	read-only	mandatory	The F/R WAN is treated as a token ring. This variable only has significance if more than 1 F/R port is configured. The default value for this field is 1.
1.3.6.1.4.1.485.3.5.5.1.1.19	ColumnframeRelayIPAddress	read-only	mandatory	This is the IP Address of this interface.
1.3.6.1.4.1.485.3.5.5.1.1.20	ColumnframeRelayNetworkMask	read-only	mandatory	This is the network mask to be used on this interface.
1.3.6.1.4.1.485.3.5.5.1.1.21	ColumnframeRelayDefaultGatewayAddress	read-only	mandatory	Default gateway address to be used when sending responses on this interface.
1.3.6.1.4.1.485.3.5.5.1.1.22	ColumnframeRelaySessSwitchThreshold	read-only	mandatory	Describes the session switch threshold for a session to switch between eVR and pVR. The value represents the LLC time-out occurrence for any session on this po…
1.3.6.1.4.1.485.3.5.5.1.1.23	ColumnframeRelaySwitchedBackup	read-only	mandatory	Defines the switched backup protocol used for dial backup. The range of this parameter is NONE or RACAL DTR-initiated. The default value is NONE.
1.3.6.1.4.1.485.3.5.5.1.1.24	ColumnframeRelaySwitchedLineWaitTimer	read-only	mandatory	This parameter defines the maximum amount of time the FrameNode waits for the DAP to establish a dial connection before switching back to the dedicated line. T…
1.3.6.1.4.1.485.3.5.5.1.1.25	ColumnframeRelayDedLineWaitTimer	read-only	mandatory	The FCC regulation for Autodialers requires that an Autodialer waits between successive dial operations. This parameter satisfies the FCC requirements. It cont…
1.3.6.1.4.1.485.3.5.5.1.1.26	ColumnframeRelayCommittedBurst	read-write	mandatory	This parameter specifies the maximum number of bits, during time interval Tc, the network agrees to accept under normal conditions. This parameter must match t…
1.3.6.1.4.1.485.3.5.5.1.1.27	ColumnframeRelayExcessBurst	read-write	mandatory	This is the maximum number of uncommitted bits, during time interval Tc, the network accepts above the committed burst size Bc. When the Excess burst Governor …
1.3.6.1.4.1.485.3.5.5.1.1.28	ColumnframeRelayBridgingProtocol	read-write	mandatory	This parameter specifies the bridging protocol to be used over Frame Relay link. This parameter has no effect if bridging is not turned on. The range of this p…
1.3.6.1.4.1.485.3.5.5.1.1.29	ColumnframeRelayProxyARP	read-write	mandatory	This parameter defines whether PROXY ARP is enabled for F/R attached devices or not. Range of this parameter is ENABLED or DISABLED. The value is 'DISABLED'.
1.3.6.1.4.1.485.3.5.5.1.1.30	ColumnframeRelaySecondDefaultGatewayAddress	read-only	mandatory	Second Default gateway address to be used when sending responses on this interface.
1.3.6.1.4.1.485.3.5.5.1.1.31	ColumnframeRelayAlternateIPAddress	read-only	mandatory	This is the Alternate IP Address for single port dial up connection.
1.3.6.1.4.1.485.3.5.5.1.1.32	ColumnframeRelayAlternateNetmask	read-only	mandatory	This is the Alternate network mask for IP for single port dial up connecton.
1.3.6.1.4.1.485.3.5.5.1.1.33	ColumnframeRelayLLC2FrameFormat	read-write	mandatory	This parameter specifies the LLC2 frame format to be used over Frame Relay link. The range of this parameter is Token Ring, Ethernet Version 2, IEEE 802.3 or A…
1.3.6.1.4.1.485.3.5.5.1.1.34	ColumnframeRelayMultiflagSeparation	read-write	mandatory	This parameter specifies whether the unit will insert more than one flag between frames. The range of this parameter is yes and no. The value is 'no'.
1.3.6.1.4.1.485.3.5.5.1.1.35	ColumnframeRelayRestrictTerminateSessUsage	read-write	mandatory	This parameter specifies whether terminated sessions are to follow spanning tree states or not over Frame Relay Link. The range of this parameter is No and Spa…
1.3.6.1.4.1.485.3.5.5.1.1.36	ColumnframeRelayRIPUpdtTimer	read-only	mandatory	Defines frequency at which the RIP packets are sent over this interface. The range of this parameter is from 10 seconds to 180 seconds. A value of 0 implies no…
1.3.6.1.4.1.485.3.5.5.1.1.37	ColumnframeRelayRIPAge	read-only	mandatory	Defines frequency at which the learned RIP entries are removed if not corresponding RIP update is received. The range of this parameter is from 40 seconds to 5…
1.3.6.1.4.1.485.3.5.5.1.1.38	ColumnframeRelaySAPUpdtTimer	read-only	mandatory	Defines frequency at which the SAP packets are sent over this interface. The range of this parameter is from 10 seconds to 180 seconds. A value of 0 implies th…
1.3.6.1.4.1.485.3.5.5.1.1.39	ColumnframeRelaySAPAge	read-only	mandatory	Defines frequency at which the learned SAP entries are removed if not corresponding SAP update is received. The range of this parameter is from 40 seconds to 7…
1.3.6.1.4.1.485.3.5.5.1.1.40	ColumnframeRelayRSM	read-only	mandatory	The Routing Summary Information parameter indicates whether the routing summary information should be generated in the RIP on that interface. If RSM is set to …
1.3.6.1.4.1.485.3.5.5.1.1.41	ColumnframeRelayARP	read-only	mandatory	The ARP parameter indicates what format of ARP should be generated. Default value is 'Auto'
1.3.6.1.4.1.485.3.5.5.1.1.42	ColumnframeRelayCTS	read-only	mandatory	Defines whether CTS is an input signal used to determine the port status. This parameter is applicable if clocking is set to external. For internal clocking th…
1.3.6.1.4.1.485.3.5.5.1.1.43	ColumnframeRelayDCD	read-only	mandatory	Defines whether DCD is required as input signal or ignored. This parameter is applicable if the clocking is set to external. For internal clocking the paramete…
1.3.6.1.4.1.485.3.5.5.1.1.44	ColumnframeRelayDSR	read-only	mandatory	Defines whether DSR is required as input signal or ignored. This parameter is applicable if the clocking is set to external. For internal clocking the paramete…
1.3.6.1.4.1.485.3.5.5.1.1.45	ColumnframeRelayDTR	read-only	mandatory	Defines whether DTR is required as input signal or ignored. This parameter is applicable if the clocking is set to internal. For external clocking the paramete…
1.3.6.1.4.1.485.3.5.5.1.1.46	ColumnframeRelayRTS	read-only	mandatory	Defines whether RTS is an input signal to determine the port status. This parameter is applicable if the clocking is set to internal. For external clocking the…
1.3.6.1.4.1.485.3.5.5.1.1.47	ColumnframeRelayReturnClock	read-only	mandatory	Defines whether Return Clock (SCTE) is available as input signal or ignored. This parameter is applicable if the clocking is set to internal. For external cloc…
1.3.6.1.4.1.485.3.5.5.2	TableframeRelayStatsTable	not-accessible	mandatory	A table of Frame Relay information.
1.3.6.1.4.1.485.3.5.5.2.1	RowframeRelayStatsEntry	not-accessible	mandatory	An entry consisting of port information for a particular Frame Relay port.
1.3.6.1.4.1.485.3.5.5.2.1.1	ColumnframeRelayStatsPortIndex	read-only	mandatory	The port number that uniquely identifies this Frame Relay port.
1.3.6.1.4.1.485.3.5.5.2.1.2	ColumnframeRelayInOctets	read-only	mandatory	The number of bytes received inclusive of all valid bytes in the frame relay frame except for the CRC field (frame relay header included).
1.3.6.1.4.1.485.3.5.5.2.1.3	ColumnframeRelayOutOctets	read-only	mandatory	The number of bytes transmitted inclusive of all bytes in the frame relay frame except for the CRC field (frame relay header included).
1.3.6.1.4.1.485.3.5.5.2.1.4	ColumnframeRelaySampleDuration	read-only	mandatory	The sample duration in seconds for Frame Relay Statistics for this port.
1.3.6.1.4.1.485.3.5.5.2.1.5	ColumnframeRelayOverruns	read-only	mandatory	The number of receiver overruns.
1.3.6.1.4.1.485.3.5.5.2.1.6	ColumnframeRelayCRCErrors	read-only	mandatory	The number of received CRC errors.
1.3.6.1.4.1.485.3.5.5.2.1.7	ColumnframeRelayRecvAborts	read-only	mandatory	The number of received frame aborts received.
1.3.6.1.4.1.485.3.5.5.2.1.8	ColumnframeRelayTxDe	read-only	mandatory	Total number of frames sent with the DE bit.
1.3.6.1.4.1.485.3.5.5.2.1.9	ColumnframeRelayRxDe	read-only	mandatory	Total number of frames received with the DE bit.
1.3.6.1.4.1.485.3.5.5.2.1.10	ColumnframeRelaySwitchedAttempts	read-only	mandatory	The total number of times a switched backup is attempted.
1.3.6.1.4.1.485.3.5.5.2.1.11	ColumnframeRelaySwitchedAttemptsSuccessful	read-only	mandatory	The total number of times switched backup attempts were successful.
1.3.6.1.4.1.485.3.5.6	NodelineAsyncGroup
1.3.6.1.4.1.485.3.5.6.1	TableasyncConfigTable	not-accessible	mandatory	A table of Async port information.
1.3.6.1.4.1.485.3.5.6.1.1	RowasyncConfigEntry	not-accessible	mandatory	An entry consisting of port information for a particular async port.
1.3.6.1.4.1.485.3.5.6.1.1.1	ColumnasyncConfigPortIndex	read-only	mandatory	The port number that uniquely identifies this port.
1.3.6.1.4.1.485.3.5.6.1.1.2	ColumnasyncConfigType	read-only	mandatory	The port type. HASC (Host Async) ports are for attaching to an Async Alarm Central Processor. TASC ports (Terminal Async) ports are for attaching to Alarm Cont…
1.3.6.1.4.1.485.3.5.6.1.1.3	ColumnasyncNAUName	read-only	mandatory	The NAU name of this port. The default value for this field is all blank (filled with ASCII space 0x20 characters).
1.3.6.1.4.1.485.3.5.6.1.1.4	ColumnasyncInitState	read-only	mandatory	The initial state of the async port. If configured for 'in-service', then the Async port will be brougt up automattically when the unit is powered up. If confi…
1.3.6.1.4.1.485.3.5.6.1.1.5	ColumnasyncCarrier	read-only	mandatory	This field indicates whether Carrier (a.k.a. CD or DCD, RS-232 pin 8) is constant or switched for DCE devices (internally clocked), or Request To Send (a.k.a. …
1.3.6.1.4.1.485.3.5.6.1.1.6	ColumnasyncSpeed	read-only	mandatory	The ports speed in bits per second. The default value is 300 bits per second. Speeds higher than 19200 are not supported.
1.3.6.1.4.1.485.3.5.6.1.1.7	ColumnasyncPhysicalType	read-only	mandatory	Physical RS-232 type emulated by the port. The default value is 2 or DCE.
1.3.6.1.4.1.485.3.5.6.1.1.8	ColumnasyncStopBits	read-only	mandatory	Number of stop bits generated for transmit characters (received characters may have any number of bits regardless of the configuration). The default value is 1.
1.3.6.1.4.1.485.3.5.6.1.1.9	ColumnasyncParity	read-only	mandatory	Parity type generated for transmit characters and checked for receive characters. If ODD or EVEN, then if a character is received with invalid parity, it is di…
1.3.6.1.4.1.485.3.5.6.1.1.10	ColumnasyncDataBits	read-only	mandatory	Number of data bits (not including the parity bit). The default value is 8.
1.3.6.1.4.1.485.3.5.6.1.1.11	ColumnasyncIdleTimer	read-only	mandatory	The idle timer is amount of time (in milliseconds) used to determine when a complete message has been received from the line. If configured as 0, then this tim…
1.3.6.1.4.1.485.3.5.6.1.1.12	ColumnasyncTxFrameGap	read-only	mandatory	The TX frame gap is analogous to the idle timer, but is used to separate messages received from the network by gaps in time so that the Async device can distin…
1.3.6.1.4.1.485.3.5.6.1.1.13	ColumnasyncRxForwardingCount	read-only	mandatory	The Async receive forwarding count is used to forward messages when a configured number of characters is received from the Async line. This must be configured …
1.3.6.1.4.1.485.3.5.6.1.1.14	ColumnasyncEiaSignalForwarding	read-only	mandatory	The Async EIA signal forwarding is used to cause receive data to be forwarding based on a change of EIA RS-232 control signals. If configured as a DCE, and thi…
1.3.6.1.4.1.485.3.5.6.1.1.15	ColumnasyncAddressOffset	read-only	mandatory	If the address offset is specified as zero, then the data is not parsed to find a device address in order to direct the data to a specified LLC connection. If …
1.3.6.1.4.1.485.3.5.6.1.1.16	ColumnasyncRTC	read-only	mandatory	Defines whether the alarms system protocol has a record termination(forwarding character). The valid range is from hex 01 to hex ff. The default value is not d…
1.3.6.1.4.1.485.3.5.6.1.1.17	ColumnasyncCTS	read-only	mandatory	Defines whether CTS is an input signal used to determine the port status. This parameter is applicable if clocking is set to external. For internal clocking th…
1.3.6.1.4.1.485.3.5.6.1.1.18	ColumnasyncDCD	read-only	mandatory	Defines whether DCD is required as input signal or ignored. This parameter is applicable if the clocking is set to external. For internal clocking the paramete…
1.3.6.1.4.1.485.3.5.6.1.1.19	ColumnasyncDSR	read-only	mandatory	Defines whether DSR is required as input signal or ignored. This parameter is applicable if the clocking is set to external. For internal clocking the paramete…
1.3.6.1.4.1.485.3.5.6.1.1.20	ColumnasyncDTR	read-only	mandatory	Defines whether DTR is required as input signal or ignored. This parameter is applicable if the clocking is set to internal. For external clocking the paramete…
1.3.6.1.4.1.485.3.5.6.1.1.21	ColumnasyncRTS	read-only	mandatory	Defines whether RTS is an input signal to determine the port status. This parameter is applicable if the clocking is set to internal. For external clocking the…
1.3.6.1.4.1.485.3.5.6.1.1.22	ColumnasyncReturnClock	read-only	mandatory	Defines whether Return Clock (SCTE) is available as input signal or ignored. This parameter is applicable if the clocking is set to internal. For external cloc…
1.3.6.1.4.1.485.3.5.6.1.1.23	ColumnasyncOrt	read-only	mandatory	The ORT command is a new port level command. By default, the setting will be YES to set the N2 value to zero, but can be set to NO to indicate that the normal …
1.3.6.1.4.1.485.3.5.6.2	TableasyncStatsTable	not-accessible	mandatory	A table of Async information.
1.3.6.1.4.1.485.3.5.6.2.1	RowasyncStatsEntry	not-accessible	mandatory	An entry consisting of port information for a particular Async port.
1.3.6.1.4.1.485.3.5.6.2.1.1	ColumnasyncStatsPortIndex	read-only	mandatory	The port number that uniquely identifies this Async port.
1.3.6.1.4.1.485.3.5.6.2.1.2	ColumnasyncPortType	read-only	mandatory	The port type. HASC (Host Async) ports are for attaching to an Async Alarm Central Processor. TASC ports (Terminal Async) ports are for attaching to Alarm Cont…
1.3.6.1.4.1.485.3.5.6.2.1.3	ColumnasyncInOctets	read-only	mandatory	The number of bytes received.
1.3.6.1.4.1.485.3.5.6.2.1.4	ColumnasyncOutOctets	read-only	mandatory	The number of bytes sent.
1.3.6.1.4.1.485.3.5.6.2.1.5	ColumnasyncInMessages	read-only	mandatory	The number of messages received.
1.3.6.1.4.1.485.3.5.6.2.1.6	ColumnasyncOutMessages	read-only	mandatory	The number of messages sent.
1.3.6.1.4.1.485.3.5.6.2.1.7	ColumnasyncInMsgDiscarded	read-only	mandatory	The number of received messages discarded.
1.3.6.1.4.1.485.3.5.6.2.1.8	ColumnasyncOutMsgDiscarded	read-only	mandatory	The number of sent messages discarded.
1.3.6.1.4.1.485.3.5.6.2.1.9	ColumnasyncXmtFailures	read-only	mandatory	The number of failures in transmission.
1.3.6.1.4.1.485.3.5.6.2.1.10	ColumnasyncRcvMsgForwarded	read-only	mandatory	The number of received messages forwarded.
1.3.6.1.4.1.485.3.5.6.2.1.11	ColumnasyncRcvMsgErrors	read-only	mandatory	The number of errors detected in receiving messages.
1.3.6.1.4.1.485.3.5.6.2.1.12	ColumnasyncRcvCharsDiscarded	read-only	mandatory	The number of received characters discarded.
1.3.6.1.4.1.485.3.5.6.2.1.13	ColumnasyncRcvParityErrors	read-only	mandatory	The number of parity errors detected.
1.3.6.1.4.1.485.3.5.6.2.1.14	ColumnasyncRcvFramingErrors	read-only	mandatory	The number of errors detected in receiving frames.
1.3.6.1.4.1.485.3.5.6.2.1.15	ColumnasyncRcvFifoOverruns	read-only	mandatory	The number FIFO receive overruns detected.
1.3.6.1.4.1.485.3.5.6.2.1.16	ColumnasyncRcvCharsOverruns	read-only	mandatory	The number of character receive overruns detected.
1.3.6.1.4.1.485.3.5.6.2.1.17	ColumnasyncRcvBreakConditions	read-only	mandatory	The number of receive break conditions.
1.3.6.1.4.1.485.3.5.7	NodelineBisyncRjeGroup
1.3.6.1.4.1.485.3.5.7.1	TablebisyncrjeConfigTable	not-accessible	mandatory	A table of Bisync port information.
1.3.6.1.4.1.485.3.5.7.1.1	RowbisyncrjeConfigEntry	not-accessible	mandatory	An entry consisting of port information for a particular Bisync port.
1.3.6.1.4.1.485.3.5.7.1.1.1	ColumnbisyncrjeConfigPortIndex	read-only	mandatory	The port number that uniquely identifies this port. Current supported Bisync Rje numbers are 1-4.
1.3.6.1.4.1.485.3.5.7.1.1.2	ColumnbisyncrjeConfigType	read-only	mandatory	The port type. PRJE (Primary RJE) ports emulate a Host and polls the downstream controllers). SRJE ports (Secondary RJE) ports emulate a line with Terminal Con…
1.3.6.1.4.1.485.3.5.7.1.1.3	ColumnbisyncrjeNAUName	read-only	mandatory	The NAU name of this port. The default value for this field is all blank (filled with ASCII space 0x20 characters).
1.3.6.1.4.1.485.3.5.7.1.1.4	ColumnbisyncrjeInitState	read-only	mandatory	The initial state of the Bisync RJE port. If configured for 'in-service', then the Bisync RJE port will be brougt up automattically when the unit is powered up…
1.3.6.1.4.1.485.3.5.7.1.1.5	ColumnbisyncrjeCarrier	read-only	mandatory	This field indicates whether Carrier is constant or switched. The default value for this parameter is 'constant'.
1.3.6.1.4.1.485.3.5.7.1.1.6	ColumnbisyncrjeClocking	read-only	mandatory	Clocking source for this port. Setting 'internal' will cause the port to emulate a physical DCE, and setting external will cause the port to emulate a physical…
1.3.6.1.4.1.485.3.5.7.1.1.7	ColumnbisyncrjeSpeed	read-only	mandatory	The ports speed in bits per second. The default value is 9600 bits per second. Speeds higher than 128000 are not supported.
1.3.6.1.4.1.485.3.5.7.1.1.8	ColumnbisyncrjeReplyTimer	read-only	mandatory	The time to wait for a response in seconds. The default value for this field is 3 seconds.
1.3.6.1.4.1.485.3.5.7.1.1.9	ColumnbisyncrjeRetries	read-only	mandatory	The maximum number of retries (N2 value) before failing a CU. The default value for this field is 8.
1.3.6.1.4.1.485.3.5.7.1.1.10	ColumnbisyncrjeCodeSet	read-only	mandatory	This parameter sets code set to be used for RJE line. The range of this parameter is ASCII and EBCDIC. The default value for this field is EBCDIC.
1.3.6.1.4.1.485.3.5.7.1.1.11	ColumnbisyncrjeCTS	read-only	mandatory	Defines whether CTS is an input signal used to determine the port status. This parameter is applicable if clocking is set to external. For internal clocking th…
1.3.6.1.4.1.485.3.5.7.1.1.12	ColumnbisyncrjeDCD	read-only	mandatory	Defines whether DCD is required as input signal or ignored. This parameter is applicable if the clocking is set to external. For internal clocking the paramete…
1.3.6.1.4.1.485.3.5.7.1.1.13	ColumnbisyncrjeDSR	read-only	mandatory	Defines whether DSR is required as input signal or ignored. This parameter is applicable if the clocking is set to external. For internal clocking the paramete…
1.3.6.1.4.1.485.3.5.7.1.1.14	ColumnbisyncrjeDTR	read-only	mandatory	Defines whether DTR is required as input signal or ignored. This parameter is applicable if the clocking is set to internal. For external clocking the paramete…
1.3.6.1.4.1.485.3.5.7.1.1.15	ColumnbisyncrjeRTS	read-only	mandatory	Defines whether RTS is an input signal to determine the port status. This parameter is applicable if the clocking is set to internal. For external clocking the…
1.3.6.1.4.1.485.3.5.7.1.1.16	ColumnbisyncrjeReturnClock	read-only	mandatory	Defines whether Return Clock (SCTE) is available as input signal or ignored. This parameter is applicable if the clocking is set to internal. For external cloc…
1.3.6.1.4.1.485.3.5.7.2	TablebisyncrjeStatsTable	not-accessible	mandatory	A table of Bisync information.
1.3.6.1.4.1.485.3.5.7.2.1	RowbisyncrjeStatsEntry	not-accessible	mandatory	An entry consisting of port information for a particular Bisync port.
1.3.6.1.4.1.485.3.5.7.2.1.1	ColumnbisyncrjeStatsPortIndex	read-only	mandatory	The port number that uniquely identifies this Bisync RJE port. Current supported numbers are 1-4.
1.3.6.1.4.1.485.3.5.7.2.1.2	ColumnbisyncrjePortType	read-only	mandatory	The port type.
1.3.6.1.4.1.485.3.5.7.2.1.3	ColumnbisyncrjeInChrs	read-only	mandatory	The number of Characters received.
1.3.6.1.4.1.485.3.5.7.2.1.4	ColumnbisyncrjeOutChrs	read-only	mandatory	The number of Characters sent.
1.3.6.1.4.1.485.3.5.7.2.1.5	ColumnbisyncrjeInTrns	read-only	mandatory	The number of Transactions received.
1.3.6.1.4.1.485.3.5.7.2.1.6	ColumnbisyncrjeOutTrns	read-only	mandatory	The number of Transactions sent.
1.3.6.1.4.1.485.3.5.7.2.1.7	ColumnbisyncrjeInRetr	read-only	mandatory	The number of Retransmits received.
1.3.6.1.4.1.485.3.5.7.2.1.8	ColumnbisyncrjeOutRetr	read-only	mandatory	The number of Retransmits sent.
1.3.6.1.4.1.485.3.5.7.2.1.9	ColumnbisyncrjeInEnq	read-only	mandatory	The number of ENQ received.
1.3.6.1.4.1.485.3.5.7.2.1.10	ColumnbisyncrjeOutEnq	read-only	mandatory	The number of ENQ sent.
1.3.6.1.4.1.485.3.5.7.2.1.11	ColumnbisyncrjeInEtb	read-only	mandatory	The number of ETB received.
1.3.6.1.4.1.485.3.5.7.2.1.12	ColumnbisyncrjeOutEtb	read-only	mandatory	The number of ETB sent.
1.3.6.1.4.1.485.3.5.7.2.1.13	ColumnbisyncrjeInEtx	read-only	mandatory	The number of ETX received.
1.3.6.1.4.1.485.3.5.7.2.1.14	ColumnbisyncrjeOutEtx	read-only	mandatory	The number of ETX sent.
1.3.6.1.4.1.485.3.5.7.2.1.15	ColumnbisyncrjeWack	read-only	mandatory	The number of WACK received.
1.3.6.1.4.1.485.3.5.7.2.1.16	ColumnbisyncrjeRvi	read-only	mandatory	The number of RVI received.
1.3.6.1.4.1.485.3.5.8	NodelineDialBackupGroup
1.3.6.1.4.1.485.3.5.8.1	TabledialbackupConfigTable	not-accessible	mandatory	A table of Sync product dial backup information.
1.3.6.1.4.1.485.3.5.8.1.1	RowdialbackupConfigEntry	not-accessible	mandatory	An entry consisting of port information for a particular Sync product dial backup port.
1.3.6.1.4.1.485.3.5.8.1.1.1	ColumndialbackupConfigPortIndex	read-only	mandatory	This port uniquely identifies the dial backup port. Range is a valid port number.
1.3.6.1.4.1.485.3.5.8.1.1.2	ColumndialbackupPortType	read-only	mandatory	The Dial backup connect Type.
1.3.6.1.4.1.485.3.5.8.1.1.3	ColumndialbackupConnectType	read-only	mandatory	The Dial backup connect Type.
1.3.6.1.4.1.485.3.5.8.1.1.4	ColumndialbackupFirstDedicatedPort	read-only	mandatory	This defines a frame relay PVC which will cause dial backup if it is declared as failed (deactivated) by the network. Port number is a valid Frame Relay and DL…
1.3.6.1.4.1.485.3.5.8.1.1.5	ColumndialbackupassociatedDLCIDedicated	read-only	mandatory	This defines a frame relay PVC which will cause dial backup if it is declared as failed (deactivated) by the network. DLCI is a valid Frame Relay DLCI.
1.3.6.1.4.1.485.3.5.8.1.1.6	ColumndialbackupSecondDedicatedPort	read-only	mandatory	This defines a second frame relay PVC which will cause dial backup if it is declared as failed (deactivated) by the network. Port number is a valid Frame Relay…
1.3.6.1.4.1.485.3.5.8.1.1.7	ColumndialbackupassociatedDLCISecond	read-only	mandatory	This defines a second frame relay PVC which will cause dial backup if it is declared as failed (deactivated) by the network. DLCI is a valid Frame Relay DLCI.
1.3.6.1.4.1.485.3.5.8.1.1.8	ColumndialbackupDedicatedPort	read-only	mandatory	When this port fails, dial connection is activated. Range is a valid port number. The default value for this field is 1.
1.3.6.1.4.1.485.3.5.8.1.1.9	ColumndialbackupDedicatedLMIPort	read-only	mandatory	When this port looses LMI connectivity, dial connection is activated. Range is a valid number. The default value for this field is 1.
1.3.6.1.4.1.485.3.5.8.1.1.10	ColumndialbackupDialInactivityTimer	read-only	mandatory	This parameter defines inactivity timer for dial connection. Expiration of this timer will cause dial connection to disconnect. The range of this parameter is …
1.3.6.1.4.1.485.3.5.8.1.1.11	ColumndialbackupDialSuspendTimer	read-only	mandatory	Defines a duration for which the dial connection. will not be attempted after the dial connection is torn down. The range is 0..9999 seconds. Value of 0 disabl…
1.3.6.1.4.1.485.3.5.8.1.1.12	ColumndialbackupModemInitString	read-only	mandatory	Defins a modem intialization string. The field is 40 characters long. The default value for this field is all blank (filled with ASCII space 0x20 characters).
1.3.6.1.4.1.485.3.5.8.1.1.13	ColumndialbackupModemDialString	read-only	mandatory	Defins a modem dial string to activate dial connection. This field is up to 40 characters long. Dial phone number may be specified here. The default value for …
1.3.6.1.4.1.485.3.5.8.1.1.14	ColumndialbackupModemHangString	read-only	mandatory	Defines a modem hang up string to deactivate dial connection. This field is up to 20 characters long. The default value for this field is all blank (filled wit…
1.3.6.1.4.1.485.3.5.8.1.1.15	ColumndialbackupDialDelayTimer	read-only	mandatory	Defines a duration for which the dial connecton will not be attempted after need to initiate dial connection is detected. The range of this parameter is 0..999…
1.3.6.1.4.1.485.3.5.8.1.1.16	ColumndialbackupTreatLLCControlCharacters	read-only	mandatory	Defines whether LLC control frames (TEST, XID, RR, RNR, REJ, DISC, UA, DM, FRMR etc. except I frames) are to be considered as user data or not. For a dial back…
1.3.6.1.4.1.485.3.5.8.2	TabledialbackupStatsTable	not-accessible	mandatory	A table of Frame Relay information.
1.3.6.1.4.1.485.3.5.8.2.1	RowdialbackupStatsEntry	not-accessible	mandatory	An entry consisting of port information for a particular Frame Relay port.
1.3.6.1.4.1.485.3.5.8.2.1.1	ColumndialbackupStatsPortIndex	read-only	mandatory	The port number that uniquely identifies this Dial Backup port.
1.3.6.1.4.1.485.3.5.8.2.1.2	ColumndialbackupSuccatmpt	read-only	mandatory	The number of successful dial backup attempts.
1.3.6.1.4.1.485.3.5.8.2.1.3	Columndialbackupunsuccatmpt	read-only	mandatory	The number of unsuccessful dial backup attempts.
1.3.6.1.4.1.485.3.5.8.2.1.4	Columndialbackupinact	read-only	mandatory	The Number of times inactivity timer expired.
1.3.6.1.4.1.485.3.5.9	NodelineX25Group
1.3.6.1.4.1.485.3.5.9.1	Tablex25ConfigTable	not-accessible	mandatory	A table of X25 information.
1.3.6.1.4.1.485.3.5.9.1.1	Rowx25ConfigEntry	not-accessible	mandatory	An entry consisting of port information for a particular X25 port.
1.3.6.1.4.1.485.3.5.9.1.1.1	Columnx25ConfigPortIndex	read-only	mandatory	The port number that uniquely identifies this port. Current supported X.25 numbers are 1-4.
1.3.6.1.4.1.485.3.5.9.1.1.2	Columnx25ConfigType	read-only	mandatory	The port type. XDCE () ports is a logical DCE device waits to receive an incoming call from the X.25 network. XDTE ports is a logical DTE device initiates a to…
1.3.6.1.4.1.485.3.5.9.1.1.3	Columnx25NAUName	read-only	mandatory	The NAU name of this port. The default value for this field is all blank (filled with ASCII space 0x20 characters).
1.3.6.1.4.1.485.3.5.9.1.1.4	Columnx25InitState	read-only	mandatory	The initial state of the X.25 port. If configured for 'in-service', then the X.25 port will be brougt up automattically when the unit is powered up. If configu…
1.3.6.1.4.1.485.3.5.9.1.1.5	Columnx25Clocking	read-only	mandatory	Clocking source for this port. Setting 'internal' will cause the port to emulate a physical DCE, and setting external will cause the port to emulate a physical…
1.3.6.1.4.1.485.3.5.9.1.1.6	Columnx25DTEAddress	read-only	mandatory	This parameter specifies the DTE address this port will use to access the X.25 network.
1.3.6.1.4.1.485.3.5.9.1.1.7	Columnx25LinkWindowSize	read-only	mandatory	This parameter sets the maximum number of concurrent unacknowledged I frames at the X.25 data link level. The default value is 7.
1.3.6.1.4.1.485.3.5.9.1.1.8	Columnx25T1Timer	read-only	mandatory	The SDLC T1 timer value in 20ths of a second. The default value is 60 (3 seconds).
1.3.6.1.4.1.485.3.5.9.1.1.9	Columnx25MaxRetries	read-only	mandatory	The maximum number of retries (N2 value) before failing a PU. The default value for this field is 8.
1.3.6.1.4.1.485.3.5.9.1.1.10	Columnx25PortSpeed	read-only	mandatory	The ports speed in 100 bits per second. The default value is 64000 bits per second. Speeds higher than 19200 are not supported on RS-232 ports units (must be V…
1.3.6.1.4.1.485.3.5.9.1.1.11	Columnx25ReceiveWindowSize	read-only	mandatory	This parameter determines the number of consecutive data packets that the sync unit can receive before requiring an acknowledgment. The default value is 2.
1.3.6.1.4.1.485.3.5.9.1.1.12	Columnx25TransmitWindowSize	read-only	mandatory	This parameter determines the number of consecutive data packets to be transmitted on the X.25 network before requiring an acknowledgment. The value you config…
1.3.6.1.4.1.485.3.5.9.1.1.13	Columnx25ReceivePacketSize	read-only	mandatory	This parameter defines the size of packets received from the X.25 network in bytes. This value must match the configuration of your X.25 network provider. The …
1.3.6.1.4.1.485.3.5.9.1.1.14	Columnx25TransmitPacketSize	read-only	mandatory	This parameter defines the size of packets transmitted across the X.25 network in bytes. This value must match the configuration of the X.25 network. The defau…
1.3.6.1.4.1.485.3.5.9.1.1.15	Columnx25LowTwoWayChannel	read-only	mandatory	This parameter specifies the X.25 packet lower-bound channel number for this physical access line. The default value is 1.
1.3.6.1.4.1.485.3.5.9.1.1.16	Columnx25HighTwoWayChannel	read-only	mandatory	This parameter specifies the X.25 packet upper-bound channel number for this physical access line. Note: This value must be greater than the Low Two-Way Channe…
1.3.6.1.4.1.485.3.5.9.1.1.17	Columnx25UseCallingAddress	read-only	mandatory	This parameter determines whether the DTE Address assigned to the port you are configuring should be included as a calling address in outgoing call packets. Th…
1.3.6.1.4.1.485.3.5.9.1.1.18	Columnx25ForwardingUnit	read-only	mandatory	This parameter limits how many message packets can accumulate before the unit forwards them to higher bytes. The default value is 'EOM'.
1.3.6.1.4.1.485.3.5.9.1.1.19	Columnx25DevicePacketSize	read-only	mandatory	When the sync unit makes a call on behalf of any configured device, the packet size determines parameter negotiation between the calling and the called packet …
1.3.6.1.4.1.485.3.5.9.1.1.20	Columnx25DeviceWindowSize	read-only	mandatory	When the sync unit makes a call on behalf of any device, the window size determines parameter negotiation between the calling and the called packet handlers. N…
1.3.6.1.4.1.485.3.5.9.1.1.21	Columnx25PlaceReverseChargeCalls	read-only	mandatory	This parameter determines whether the Sync unit will place reverse charge requests on outgoing calls. The default value is 'No'.
1.3.6.1.4.1.485.3.5.9.1.1.22	Columnx25AcceptReverseChargeCalls	read-only	mandatory	This parameter determines whether the Sync unit will accept reverse charge requests from incoming calls. The default value is 'No'.
1.3.6.1.4.1.485.3.5.9.1.1.23	Columnx25NPS	read-only	mandatory	This parameter indicates if the QLLC conversion NODE is connecting to a NPSI front-end and is to take on a secondary role. The default value is 'No'.
1.3.6.1.4.1.485.3.5.9.1.1.24	Columnx25CTS	read-only	mandatory	Defines whether CTS is an input signal used to determine the port status. This parameter is applicable if clocking is set to external. For internal clocking th…
1.3.6.1.4.1.485.3.5.9.1.1.25	Columnx25DCD	read-only	mandatory	Defines whether DCD is required as input signal or ignored. This parameter is applicable if the clocking is set to external. For internal clocking the paramete…
1.3.6.1.4.1.485.3.5.9.1.1.26	Columnx25DSR	read-only	mandatory	Defines whether DSR is required as input signal or ignored. This parameter is applicable if the clocking is set to external. For internal clocking the paramete…
1.3.6.1.4.1.485.3.5.9.1.1.27	Columnx25DTR	read-only	mandatory	Defines whether DTR is required as input signal or ignored. This parameter is applicable if the clocking is set to internal. For external clocking the paramete…
1.3.6.1.4.1.485.3.5.9.1.1.28	Columnx25RTS	read-only	mandatory	Defines whether RTS is an input signal to determine the port status. This parameter is applicable if the clocking is set to internal. For external clocking the…
1.3.6.1.4.1.485.3.5.9.1.1.29	Columnx25ReturnClock	read-only	mandatory	Defines whether Return Clock (SCTE) is available as input signal or ignored. This parameter is applicable if the clocking is set to internal. For external cloc…
1.3.6.1.4.1.485.3.5.9.1.1.30	Columnx25IPAddress	read-only	mandatory	This is the IP Address of this interface.
1.3.6.1.4.1.485.3.5.9.1.1.31	Columnx25NetworkMask	read-only	mandatory	This is the network mask to be used on this interface.
1.3.6.1.4.1.485.3.5.9.1.1.32	Columnx25DefaultGatewayAddress	read-only	mandatory	Default gateway address to be used when sending responses on this interface.
1.3.6.1.4.1.485.3.5.9.1.1.33	Columnx25SecondDefaultGatewayAddress	read-only	mandatory	Second Default gateway address to be used when sending responses on this interface.
1.3.6.1.4.1.485.3.5.9.2	Tablex25StatsTable	not-accessible	mandatory	A table of X25 information.
1.3.6.1.4.1.485.3.5.9.2.1	Rowx25StatsEntry	not-accessible	mandatory	An entry consisting of port information for a particular X25 port.
1.3.6.1.4.1.485.3.5.9.2.1.1	Columnx25StatsPortIndex	read-only	mandatory	The port number that uniquely identifies this X25 port. Current supported numbers on are 1-8.
1.3.6.1.4.1.485.3.5.9.2.1.2	Columnx25PortType	read-only	mandatory	The port type. XDCE () ports is a logical DCE device waits to receive an incoming call from the X.25 network. XDTE ports is a logical DTE device initiates a to…
1.3.6.1.4.1.485.3.5.9.2.1.3	Columnx25InFrames	read-only	mandatory	The number of I-frames received.
1.3.6.1.4.1.485.3.5.9.2.1.4	Columnx25OutFrames	read-only	mandatory	The number of I-frames sent.
1.3.6.1.4.1.485.3.5.9.2.1.5	Columnx25CInFrames	read-only	mandatory	The number of Control-frames received.
1.3.6.1.4.1.485.3.5.9.2.1.6	Columnx25COutFrames	read-only	mandatory	The number of Control-frames sent.
1.3.6.1.4.1.485.3.5.9.2.1.7	Columnx25FRMRInFrames	read-only	mandatory	The number of FRMR-frames received.
1.3.6.1.4.1.485.3.5.9.2.1.8	Columnx25FRMROutFrames	read-only	mandatory	The number of FRMR-frames sent.
1.3.6.1.4.1.485.3.5.9.2.1.9	Columnx25Timeouts	read-only	mandatory	The number of Timeouts.
1.3.6.1.4.1.485.3.5.9.2.1.10	Columnx25UFrames	read-only	mandatory	The number of Undefined Frames.
1.3.6.1.4.1.485.3.5.9.2.1.11	Columnx25Samples	read-only	mandatory	The number of Samples.
1.3.6.1.4.1.485.3.5.9.2.1.12	Columnx25Sum	read-only	mandatory	The number of Active Channels Sum.
1.3.6.1.4.1.485.3.5.9.2.1.13	Columnx25SumsQ	read-only	mandatory	The number of Active Channels SumsQ.
1.3.6.1.4.1.485.3.5.9.2.1.14	Columnx25DataInPkts	read-only	mandatory	The number of Data Packets received.
1.3.6.1.4.1.485.3.5.9.2.1.15	Columnx25DataOutPkts	read-only	mandatory	The number of Data Packets sent.
1.3.6.1.4.1.485.3.5.9.2.1.16	Columnx25DataInChrs	read-only	mandatory	The number of Data Characters received.
1.3.6.1.4.1.485.3.5.9.2.1.17	Columnx25DataOutChrs	read-only	mandatory	The number of Data Characters sent.
1.3.6.1.4.1.485.3.5.9.2.1.18	Columnx25QInPkts	read-only	mandatory	The number of Q-Packets received.
1.3.6.1.4.1.485.3.5.9.2.1.19	Columnx25QOutPkts	read-only	mandatory	The number of Q-Packets sent.
1.3.6.1.4.1.485.3.5.9.2.1.20	Columnx25QInChrs	read-only	mandatory	The number of Q-Characters received.
1.3.6.1.4.1.485.3.5.9.2.1.21	Columnx25QOutChrs	read-only	mandatory	The number of Q-Characters sent.
1.3.6.1.4.1.485.3.5.9.2.1.22	Columnx25SigInPkts	read-only	mandatory	The number of Sig-Packets received.
1.3.6.1.4.1.485.3.5.9.2.1.23	Columnx25SigOutPkts	read-only	mandatory	The number of Sig-Packets sent.
1.3.6.1.4.1.485.3.5.9.2.1.24	Columnx25InResets	read-only	mandatory	The number of Resets received.
1.3.6.1.4.1.485.3.5.9.2.1.25	Columnx25OutResets	read-only	mandatory	The number of Resets sent.
1.3.6.1.4.1.485.3.5.9.2.1.26	Columnx25InRestarts	read-only	mandatory	The number of Restarts received.
1.3.6.1.4.1.485.3.5.9.2.1.27	Columnx25OutRestarts	read-only	mandatory	The number of Restarts sent.
1.3.6.1.4.1.485.3.5.10	NodelineAlcGroup
1.3.6.1.4.1.485.3.5.10.1	TablealcConfigTable	not-accessible	mandatory	A table of ALC information.
1.3.6.1.4.1.485.3.5.10.1.1	RowalcConfigEntry	not-accessible	mandatory	An entry consisting of port information for a particular ALC port.
1.3.6.1.4.1.485.3.5.10.1.1.1	ColumnalcConfigPortIndex	read-only	mandatory	The port number that uniquely identifies this port. Current supported X.25 numbers are 1-4.
1.3.6.1.4.1.485.3.5.10.1.1.2	ColumnalcConfigType	read-only	mandatory	The port type. The default is Teminal ALC.
1.3.6.1.4.1.485.3.5.10.1.1.3	ColumnalcNAUName	read-only	mandatory	The NAU name of this port. The default value for this field is all blank (filled with ASCII space 0x20 characters).
1.3.6.1.4.1.485.3.5.10.1.1.4	ColumnalcInitState	read-only	mandatory	The initial state of the X.25 port. If configured for 'in-service', then the ALC port will be brougt up automattically when the unit is powered up. If configur…
1.3.6.1.4.1.485.3.5.10.1.1.5	ColumnalcClocking	read-only	mandatory	Clocking source for this port. Setting 'internal' will cause the port to emulate a physical DCE, and setting external will cause the port to emulate a physical…
1.3.6.1.4.1.485.3.5.10.1.1.6	ColumnalcPortSpeed	read-only	mandatory	The ports speed in 100 bits per second. The default value is 9600 bits per second.
1.3.6.1.4.1.485.3.5.10.1.1.7	ColumnalcLimitSegsCharsBetweenPolls	read-only	mandatory	This parameter specifies whether to limit the number of segments sent between pools. If this parameter is set to 'yes' the parameter 'Number of Segments' and '…
1.3.6.1.4.1.485.3.5.10.1.1.8	ColumnalcNumberOfSegments	read-only	mandatory	This parameter specifies the maximum number of segments that may be sent between polls. This parameter is applicable only if 'Limit SEGs/Chars between polls' i…
1.3.6.1.4.1.485.3.5.10.1.1.9	ColumnalcNumberOfCharacters	read-only	mandatory	This parameter specifies the maximum number of characters that may be sent between polls. This parameter is applicable only if 'Limit SEGs/Chars between polls'…
1.3.6.1.4.1.485.3.5.10.1.1.10	ColumnalcNumberOfNullSeg	read-only	mandatory	This parameter specifies the maximum number of null characters that may be sent between segments. The defualt value is 0.
1.3.6.1.4.1.485.3.5.10.1.1.11	ColumnalcCTS	read-only	mandatory	Defines whether CTS is an input signal used to determine the port status. This parameter is applicable if clocking is set to external. For internal clocking th…
1.3.6.1.4.1.485.3.5.10.1.1.12	ColumnalcDCD	read-only	mandatory	Defines whether DCD is required as input signal or ignored. This parameter is applicable if the clocking is set to external. For internal clocking the paramete…
1.3.6.1.4.1.485.3.5.10.1.1.13	ColumnalcDSR	read-only	mandatory	Defines whether DSR is required as input signal or ignored. This parameter is applicable if the clocking is set to external. For internal clocking the paramete…
1.3.6.1.4.1.485.3.5.10.1.1.14	ColumnalcDTR	read-only	mandatory	Defines whether DTR is required as input signal or ignored. This parameter is applicable if the clocking is set to internal. For external clocking the paramete…
1.3.6.1.4.1.485.3.5.10.1.1.15	ColumnalcRTS	read-only	mandatory	Defines whether RTS is an input signal to determine the port status. This parameter is applicable if the clocking is set to internal. For external clocking the…
1.3.6.1.4.1.485.3.5.10.1.1.16	ColumnalcReturnClock	read-only	mandatory	Defines whether Return Clock (SCTE) is available as input signal or ignored. This parameter is applicable if the clocking is set to internal. For external cloc…
1.3.6.1.4.1.485.3.5.10.2	TablealcStatsTable	not-accessible	mandatory	A table of X25 information.
1.3.6.1.4.1.485.3.5.10.2.1	RowalcStatsEntry	not-accessible	mandatory	An entry consisting of port information for a particular X25 port.
1.3.6.1.4.1.485.3.5.10.2.1.1	ColumnalcStatsPortIndex	read-only	mandatory	The port number that uniquely identifies this Alc port. Current supported numbers on are 1-8.
1.3.6.1.4.1.485.3.5.10.2.1.2	ColumnalcPortType	read-only	mandatory	The port type. The default is Terminal Alc.
1.3.6.1.4.1.485.3.5.10.2.1.3	ColumnalcRxOverruns	read-only	mandatory	The number of Received Overruns.
1.3.6.1.4.1.485.3.5.10.2.1.4	ColumnalcBytesRx	read-only	mandatory	The number of Bytes Received.
1.3.6.1.4.1.485.3.5.10.2.1.5	ColumnalcBytesTx	read-only	mandatory	The number of Bytes Transmitted.
1.3.6.1.4.1.485.3.5.10.2.1.6	ColumnalcBytesRxDisc	read-only	mandatory	The number of Bytes Received.
1.3.6.1.4.1.485.3.5.10.2.1.7	ColumnalcBytesTxDisc	read-only	mandatory	The number of Bytes Transmitted.
1.3.6.1.4.1.485.3.5.10.2.1.8	ColumnalcPortFaults	read-only	mandatory	The number of Bytes Transmitted.
1.3.6.1.4.1.485.3.5.10.2.1.9	ColumnalcRcvCCCErrors	read-only	mandatory	The number of Bytes Transmitted.
1.3.6.1.4.1.485.3.5.10.2.1.10	ColumnalcPollTx	read-only	mandatory	The number of Bytes Transmitted.
1.3.6.1.4.1.485.3.5.10.2.1.11	ColumnalcResponseTimeouts	read-only	mandatory	The number of Bytes Transmitted.
1.3.6.1.4.1.485.3.5.10.2.1.12	ColumnalcSegRx	read-only	mandatory	The number of Segments Received.
1.3.6.1.4.1.485.3.5.10.2.1.13	ColumnalcSegTx	read-only	mandatory	The number of Segments Transmitted.
1.3.6.1.4.1.485.3.5.10.2.1.14	ColumnalcSegRxDisc	read-only	mandatory	The number of Received Segments Discarded.
1.3.6.1.4.1.485.3.5.10.2.1.15	ColumnalcSegTxDisc	read-only	mandatory	The number of Transmitted Segments Discarded.
1.3.6.1.4.1.485.3.6	NodenodePUGroup
1.3.6.1.4.1.485.3.6.1	NodepuControlGroup
1.3.6.1.4.1.485.3.6.1.1	TablepuControlTable	not-accessible	mandatory	A table for controlling lines and obtaining information.
1.3.6.1.4.1.485.3.6.1.1.1	RowpuControlEntry	not-accessible	mandatory	An entry consisting of PU information for a particular port.
1.3.6.1.4.1.485.3.6.1.1.1.1	ColumnpuControlLineIndex	read-only	mandatory	The port number that has a given PU.
1.3.6.1.4.1.485.3.6.1.1.1.2	ColumnpuControlPUAddress	read-only	mandatory	The PU address in the range of 0x01 to 0xfe.
1.3.6.1.4.1.485.3.6.1.1.1.3	ColumnpuStatus	read-write	mandatory	The status of the PU. To change status of a port an enable, enable all or disable may be set. Valid Return status are enable(d), disable(d), or failed. Command…
1.3.6.1.4.1.485.3.6.1.1.1.4	ColumnpuConnectionStatus	read-only	mandatory	The status of the LLC type 2 Connection for this SDLC PU.
1.3.6.1.4.1.485.3.6.1.1.1.5	ColumnpuLastClearCode	read-only	mandatory	A two octet field indicating the Last Clearing Cause and Diagnostic Field of the last failed connection attempt (a.k.a. call attempt) or active connection (a.k…
1.3.6.1.4.1.485.3.6.1.1.1.6	ColumnpuControlFailureCode	read-only	mandatory	This entry contains the failure codes if the associated PU is in the failed state.
1.3.6.1.4.1.485.3.6.1.1.1.7	ColumnpuControlNAUName	read-only	mandatory	The NAU name of this PU. The default value for this field is all blank (filled with ASCII space 0x20 characters).
1.3.6.1.4.1.485.3.6.1.1.1.8	ColumnpuConnectionAttemptCount	read-only	mandatory	The number of connection attempts performed. This count is set to zero at startup, and after every loss of an estabished session.
1.3.6.1.4.1.485.3.6.1.1.1.9	ColumnpuStatusIgnored	read-write	mandatory	This field is used for consolidating status of the unit. The status of this pu is not put into consideration when consolidating status of the unit if this fiel…
1.3.6.1.4.1.485.3.6.1.1.1.10	ColumnpuStatusAcknowledged	read-write	mandatory	This field is used for consolidating status of the unit. When this field is set to yes, the unit will re-consolidate its status without putting the status of t…
1.3.6.1.4.1.485.3.6.1.1.1.11	ColumnpuLastDlciCleared	read-only	mandatory	Specifies the dlci that the last clear code was associated with. If the last clear code was not associated with a virtual route, i.e. the clear was associated …
1.3.6.1.4.1.485.3.6.1.1.1.12	ColumnpuCurrentDlci	read-only	mandatory	Specifies the DLCI active for a session at this time. For LAN or X25 network interface, this field is set to 0
1.3.6.1.4.1.485.3.6.1.1.1.13	ColumnpuLastMACCleared	read-only	mandatory	Specifies the MAC address that the last clear code was associated with.
1.3.6.1.4.1.485.3.6.1.1.1.14	ColumnpuCurrentMAC	read-only	mandatory	Specifies the MAC address that the current session is associated with. For X25 network type, this is set to 0.
1.3.6.1.4.1.485.3.6.1.1.1.15	ColumnpuNetworkType	read-only	mandatory	Specifies netowrk type that the current session is associated with.
1.3.6.1.4.1.485.3.6.1.1.1.16	ColumnpuCurrentConnectionType	read-only	mandatory	Specifies network layer that the current session is associated with.
1.3.6.1.4.1.485.3.6.1.1.1.17	ColumnpuLastSVCCleared	read-only	mandatory	Specifies the LCN that the last clear code is associated with. If the last clear code was not associated with a X25 SVC, i.e. the clear was associated with the…
1.3.6.1.4.1.485.3.6.1.1.1.18	ColumnpuCurrentSVC	read-only	mandatory	Specifies the that the current session is associated with. For non X25 network type, this field is set to 0
1.3.6.1.4.1.485.3.6.1.1.1.19	ColumnpuLastLocalDTECleared	read-only	mandatory	Specifies the local DTE address that the last clear code is associated with. For non X25 network type, this field is set to 0
1.3.6.1.4.1.485.3.6.1.1.1.20	ColumnpuLastRemoteDTECleared	read-only	mandatory	Specifies the remote DTE address that the last clear code is associated with. For non X25 network type, this field is set to 0
1.3.6.1.4.1.485.3.6.1.1.1.21	ColumnpuCurrentLocalDTE	read-only	mandatory	Specifies the local DTE address that the current session is associated with. For non X25 network type, this field is set to 0
1.3.6.1.4.1.485.3.6.1.1.1.22	ColumnpuCurrentRemoteDTE	read-only	mandatory	Specifies the remote DTE address that the current session is associated with. For non X25 network type, this field is set to 0
1.3.6.1.4.1.485.3.6.1.1.1.23	ColumnpuIsDynamic	read-write	mandatory	The type of PU. YES means that the PU is a dynamic pu created by auto LLC. The puStatus for any dynamic PU must be enabled
1.3.6.1.4.1.485.3.6.2	NodepuSDLCGroup
1.3.6.1.4.1.485.3.6.2.1	TablesdlcPuConfigTable	not-accessible	mandatory	A list of PU entries.
1.3.6.1.4.1.485.3.6.2.1.1	RowsdlcPuConfigEntry	not-accessible	mandatory	This entry contains information about a given PU. The entry is indexed by the port number and the PU number.
1.3.6.1.4.1.485.3.6.2.1.1.1	ColumnsdlcPuConfigLineIndex	read-only	mandatory	The port number for which the line (CU)is configured (first level).
1.3.6.1.4.1.485.3.6.2.1.1.2	ColumnsdlcPuConfigAddress	read-only	mandatory	The PU address in the range of 0x00 to 0xfe.
1.3.6.1.4.1.485.3.6.2.1.1.3	ColumnsdlcPuNAUName	read-only	mandatory	The NAU name of this PU. The default value for this field is all blank (filled with ASCII space 0x20 characters).
1.3.6.1.4.1.485.3.6.2.1.1.4	ColumnsdlcPuInitialState	read-only	mandatory	The initial state of the PU. If configured for 'in-service', then the SDLC PU will be brougt up automattically when the unit is powered up. If configured for '…
1.3.6.1.4.1.485.3.6.2.1.1.5	ColumnsdlcPuXID	read-only	mandatory	The XID value for this PU. The XID is used to identify the PU during the LLC connection process to the remote Host or Gateway. If the field is configured to 0 …
1.3.6.1.4.1.485.3.6.2.1.1.6	ColumnsdlcPuType	read-only	mandatory	The SNA PU type. 1 = PU type 1 2 = PU type 2 3 = PU type 2.1 4 = PU type 4 5 = PU type 5 (not supported, reserved) This parameter defaults to a value of 2.
1.3.6.1.4.1.485.3.6.2.1.1.7	ColumnsdlcPuGroupPollAddress	read-only	mandatory	The PU's group address in the range of 0x01 to 0xfe. setting this value to 0 will disable the group poll feature for polling this and other PUs in a group. The…
1.3.6.1.4.1.485.3.6.2.1.1.8	ColumnsdlcPuConnectionID	read-only	mandatory	This entry defines the Connection ID to a corresponding entry in the mapping table. The default value for this field is all zeroes.
1.3.6.1.4.1.485.3.6.2.1.1.9	ColumnsdlcPuMAXOUT	read-only	mandatory	This entry defines the maximum number of outstanding I frames that the PU will allow. This field is applicable to TSDLC only.
1.3.6.1.4.1.485.3.6.2.1.1.10	ColumnsdlcPuConnectType	read-only	mandatory	The SNA PU Connection type.
1.3.6.1.4.1.485.3.6.2.2	TablesdlcPuStatsTable	not-accessible	mandatory	A list of PU statistics entries.
1.3.6.1.4.1.485.3.6.2.2.1	RowsdlcPuStatsEntry	not-accessible	mandatory	This entry contains information about a given PU. The entry is indexed by the port number and the PU number.
1.3.6.1.4.1.485.3.6.2.2.1.1	ColumnsdlcPuStatsLineIndex	read-only	mandatory	The port number for which PU is configured on.
1.3.6.1.4.1.485.3.6.2.2.1.2	ColumnsdlcPuStatsAddress	read-only	mandatory	The PU address in the range of 0x00 to 0xfe.
1.3.6.1.4.1.485.3.6.2.2.1.3	ColumnsdlcPuInIFrames	read-only	mandatory	The number of I frames received on this PU.
1.3.6.1.4.1.485.3.6.2.2.1.4	ColumnsdlcPuOutIFrames	read-only	mandatory	The number of I frames trasnmitted on this PU.
1.3.6.1.4.1.485.3.6.2.2.1.5	ColumnsdlcPuInRRFrames	read-only	mandatory	The number of RR frames received on this PU.
1.3.6.1.4.1.485.3.6.2.2.1.6	ColumnsdlcPuOutRRFrames	read-only	mandatory	The number of RR frames transmitted on this PU.
1.3.6.1.4.1.485.3.6.2.2.1.7	ColumnsdlcPuInRNRFrames	read-only	mandatory	The number of RNR frames received on this PU.
1.3.6.1.4.1.485.3.6.2.2.1.8	ColumnsdlcPuOutRNRFrames	read-only	mandatory	The number of RNR frames transmitted on this PU.
1.3.6.1.4.1.485.3.6.2.2.1.9	ColumnsdlcPuInXIDFrames	read-only	mandatory	The number of XID frames received on this PU.
1.3.6.1.4.1.485.3.6.2.2.1.10	ColumnsdlcPuOutXIDFrames	read-only	mandatory	The number of XID frames transmitted on this PU.
1.3.6.1.4.1.485.3.6.2.2.1.11	ColumnsdlcPuInTESTFrames	read-only	mandatory	The number of TEST frames received on this PU.
1.3.6.1.4.1.485.3.6.2.2.1.12	ColumnsdlcPuOutTESTFrames	read-only	mandatory	The number of TEST frames transmitted on this PU.
1.3.6.1.4.1.485.3.6.2.2.1.13	ColumnsdlcPuInSNRMFrames	read-only	mandatory	The number of SNRM frames received on this PU.
1.3.6.1.4.1.485.3.6.2.2.1.14	ColumnsdlcPuOutSNRMFrames	read-only	mandatory	The number of SNRM frames transmitted on this PU.
1.3.6.1.4.1.485.3.6.2.2.1.15	ColumnsdlcPuInDISCFrames	read-only	mandatory	The number of DISC frames received on this PU.
1.3.6.1.4.1.485.3.6.2.2.1.16	ColumnsdlcPuOutDISCFrames	read-only	mandatory	The number of DISC frames transmitted on this PU.
1.3.6.1.4.1.485.3.6.2.2.1.17	ColumnsdlcPuInDMFrames	read-only	mandatory	The number of DM frames received on this PU.
1.3.6.1.4.1.485.3.6.2.2.1.18	ColumnsdlcPuOutDMFrames	read-only	mandatory	The number of DM frames transmitted on this PU.
1.3.6.1.4.1.485.3.6.2.2.1.19	ColumnsdlcPuInUAFrames	read-only	mandatory	The number of UA frames received on this PU.
1.3.6.1.4.1.485.3.6.2.2.1.20	ColumnsdlcPuOutUAFrames	read-only	mandatory	The number of UA frames transmitted on this PU.
1.3.6.1.4.1.485.3.6.2.2.1.21	ColumnsdlcPuInFRMRFrames	read-only	mandatory	The number of FRMR frames received on this PU.
1.3.6.1.4.1.485.3.6.2.2.1.22	ColumnsdlcPuOutFRMRFrames	read-only	mandatory	The number of FRMR frames transmitted on this PU.
1.3.6.1.4.1.485.3.6.2.2.1.23	ColumnsdlcPuInRDFrames	read-only	mandatory	The number of RD frames received on this PU.
1.3.6.1.4.1.485.3.6.2.2.1.24	ColumnsdlcPuOutRDFrames	read-only	mandatory	The number of RD frames transmitted on this PU.
1.3.6.1.4.1.485.3.6.2.2.1.25	ColumnsdlcPuInUIFrames	read-only	mandatory	The number of UI frames received on this PU.
1.3.6.1.4.1.485.3.6.2.2.1.26	ColumnsdlcPuOutUIFrames	read-only	mandatory	The number of UI frames transmitted on this PU.
1.3.6.1.4.1.485.3.6.2.2.1.27	ColumnsdlcPuReTxIFrames	read-only	mandatory	The number of re-transmitted I frames on this PU.
1.3.6.1.4.1.485.3.6.2.2.1.28	ColumnsdlcPuPollResponseTimeouts	read-only	mandatory	The number of PU Poll Response timeouts for this PU.
1.3.6.1.4.1.485.3.6.3	NodepuBisyncGroup
1.3.6.1.4.1.485.3.6.3.1	TablebisyncPuConfigTable	not-accessible	mandatory	A list of Bisync CU entries.
1.3.6.1.4.1.485.3.6.3.1.1	RowbisyncPuConfigEntry	not-accessible	mandatory	This entry contains information about a given PU. The entry is indexed by the port number and the PU number.
1.3.6.1.4.1.485.3.6.3.1.1.1	ColumnbisyncPuConfigLineIndex	read-only	mandatory	The port number for which PU is configured on.
1.3.6.1.4.1.485.3.6.3.1.1.2	ColumnbisyncPuConfigAddress	read-only	mandatory	The PU address in the range of 0x00 to 0xfe.
1.3.6.1.4.1.485.3.6.3.1.1.3	ColumnbisyncPuNAUName	read-only	mandatory	The NAU name of this PU. The default value for this field is all blank (filled with ASCII space 0x20 characters).
1.3.6.1.4.1.485.3.6.3.1.1.4	ColumnbisyncPuInitialState	read-only	mandatory	The initial state of the PU. If configured for 'in-service', then the Bisync PU will be brougt up automattically when the unit is powered up. If configured for…
1.3.6.1.4.1.485.3.6.3.1.1.5	ColumnbisyncPuXID	read-only	mandatory	The XID value for this PU. The XID is used to identify the PU during the LLC connection process to the remote Host or Gateway. The unit will insert the data co…
1.3.6.1.4.1.485.3.6.3.1.1.6	ColumnbisyncPuTargetHostType	read-only	mandatory	The Target Host type. This field specifies the target host type for TBSC and is applicable to BSC-to-SNA conversion only. This parameter defaults to a value of…
1.3.6.1.4.1.485.3.6.3.1.1.7	ColumnbisyncPuMaxData	read-only	mandatory	This entry defines the SNA frame size which is the sum of SNA data and SNA header. This value must match the MAXData configured for SNA host and is applicable …
1.3.6.1.4.1.485.3.6.3.1.1.8	ColumnbisyncPuConnectionID	read-only	mandatory	This entry defines the Connection ID to a corresponding entry in the mapping table. The default value for this field is all zeroes.
1.3.6.1.4.1.485.3.6.3.1.1.9	ColumnbisyncPuConnectType	read-only	mandatory	The Bisync PU Connection type.
1.3.6.1.4.1.485.3.6.3.2	TablebisyncPuStatsTable	not-accessible	mandatory	A list of PU statistics entries.
1.3.6.1.4.1.485.3.6.3.2.1	RowbisyncPuStatsEntry	not-accessible	mandatory	This entry contains information about a given PU. The entry is indexed by the port number and the PU number.
1.3.6.1.4.1.485.3.6.3.2.1.1	ColumnbisyncPuStatsLineIndex	read-only	mandatory	The port number for which PU is configured on.
1.3.6.1.4.1.485.3.6.3.2.1.2	ColumnbisyncPuStatsAddress	read-only	mandatory	The PU address in the range of 0x00 to 0xfe.
1.3.6.1.4.1.485.3.6.3.2.1.3	ColumnbisyncPuInTransactions	read-only	mandatory	The number of PU Poll Response timeouts for this PU.
1.3.6.1.4.1.485.3.6.3.2.1.4	ColumnbisyncPuOutTransactions	read-only	mandatory	The number of PU Poll Response timeouts for this PU.
1.3.6.1.4.1.485.3.6.3.2.1.5	ColumnbisyncPuSlowPolls	read-only	mandatory	The number of PU slow polls for this PU.
1.3.6.1.4.1.485.3.6.3.2.1.6	ColumnbisyncPuPolls	read-only	mandatory	The number of PU Polls for this PU.
1.3.6.1.4.1.485.3.6.4	NodepuMappingGroup
1.3.6.1.4.1.485.3.6.4.1	TablemappingPuConfigTable	not-accessible	mandatory	This Table is obsolete. A list of PU mapping entries.
1.3.6.1.4.1.485.3.6.4.1.1	RowmappingPuConfigEntry	not-accessible	mandatory	This field is obsolete. This entry contains information about a given mapping PU. Each entry includes MAC/SAP information for a source PU and a similar informa…
1.3.6.1.4.1.485.3.6.4.1.1.1	ColumnmappingPuConfigLineIndex	read-only	mandatory	This field is obsolete. The port number for which PU is associated with. Port number 99 is a special value which is used to indicate NetView PU.
1.3.6.1.4.1.485.3.6.4.1.1.2	ColumnmappingPuConfigAddress	read-only	mandatory	This field is obsolete. The PU address in the range of 0x01 to 0xfe.
1.3.6.1.4.1.485.3.6.4.1.1.3	ColumnmappingPuSourceSAP	read-only	mandatory	This field is obsolete. The LLC source SAP value for this PU. Typically the source SAP will vary for each PU. This is due to the fact that most Sync products a…
1.3.6.1.4.1.485.3.6.4.1.1.4	ColumnmappingPuDestinationSAP	read-only	mandatory	This field is obsolete. The LLC Destination SAP value for this PU. For SNA typically the destination is almost always SAP 4. However both Host Front Ends (e.g.…
1.3.6.1.4.1.485.3.6.4.1.1.5	ColumnmappingPuDestinationMAC	read-only	mandatory	This field is obsolete. The LAN Destination MAC address used in the LLC Type 2 connection for this PU. The Token-Ring format for this field is a 6 octet (48 bi…
1.3.6.1.4.1.485.3.6.4.1.1.6	ColumnmappingPuPartnerConfigLineIndex	read-only	mandatory	This field is obsolete. The port number for the partner PU associated with source PU. Port number 99 is a special value which is used to indicate NetView PU.
1.3.6.1.4.1.485.3.6.4.1.1.7	ColumnmappingPuPartnerConfigAddress	read-only	mandatory	This field is obsolete. The PU address of the partner PU in the range of 0x01 to 0xfe.
1.3.6.1.4.1.485.3.6.4.1.1.8	ColumnmappingPuPartnerSourceSAP	read-only	mandatory	This field is obsolete. The LLC source SAP value for a partner PU. Typically the source SAP will vary for each PU. This is due to the fact that most Sync produ…
1.3.6.1.4.1.485.3.6.4.1.1.9	ColumnmappingPuPartnerDestSAP	read-only	mandatory	This field is obsolete. The LLC Destination SAP value for the partner PU. For SNA typically the destination is almost always SAP 4. However both Host Front End…
1.3.6.1.4.1.485.3.6.4.1.1.10	ColumnmappingPuPartnerDestMAC	read-only	mandatory	This field is obsolete. The LAN Destination MAC address used in the LLC Type 2 connection for the partner PU. The Token-Ring format for this field is a 6 octet…
1.3.6.1.4.1.485.3.6.4.1.1.11	ColumnmappingPuNAU	read-only	mandatory	This field is obsolete. The NAU Name. The NAU name is same for both the source PU and the partner PU. It represents one physical PU in a network.
1.3.6.1.4.1.485.3.6.4.1.1.12	ColumnmappingPuConnectID	read-only	mandatory	This field is obsolete. The connection ID. This must match a connection ID of an access line PU or another mapping PU Connection ID. The connnection ID is 0 if…
1.3.6.1.4.1.485.3.6.4.1.1.13	ColumnmappingPuXID	read-only	mandatory	This field is obsolete. The XID value for this PU. The XID is used to identify the PU during the LLC connection process to the remote Host or Gateway. For inco…
1.3.6.1.4.1.485.3.6.4.1.1.14	ColumnmappingPuDirectDLCI	read-only	mandatory	This field is obsolete. The Frame Relay DLCI used in the LLC Type 2 connection for this PU. The Frame Relay format for this field is a 2 octet (16 bit) field r…
1.3.6.1.4.1.485.3.6.4.1.1.15	ColumnmappingPuLastClearCode	read-only	mandatory	This field is obsolete. A two octet field indicating the Last Clearing Cause and Diagnostic Field of the last failed connection attempt (a.k.a. call attempt) o…
1.3.6.1.4.1.485.3.6.4.1.1.16	ColumnmappingPuConnAttemptCnt	read-only	mandatory	This field is obsolete. The number of connection attempts performed for this PU. This count is set to zero at startup, and after every loss of an estabished se…
1.3.6.1.4.1.485.3.6.4.1.1.17	ColumnmappingPuPartnerLastClearCode	read-only	mandatory	This field is obsolete. A two octet field indicating the Last Clearing Cause and Diagnostic Field of the last failed connection attempt (a.k.a. call attempt) o…
1.3.6.1.4.1.485.3.6.4.1.1.18	ColumnmappingPuPartnerConnAttemptCnt	read-only	mandatory	This field is obsolete. The number of connection attempts performed for the partner PU. This count is set to zero at startup, and after every loss of an estabi…
1.3.6.1.4.1.485.3.6.5	NodepuAsyncGroup
1.3.6.1.4.1.485.3.6.5.1	TableasyncPuConfigTable	not-accessible	mandatory	A list of PU entries.
1.3.6.1.4.1.485.3.6.5.1.1	RowasyncPuConfigEntry	not-accessible	mandatory	This entry contains information about a given PU. The entry is indexed by the port number and the PU number.
1.3.6.1.4.1.485.3.6.5.1.1.1	ColumnasyncPuConfigLineIndex	read-only	mandatory	The port number for which the line (CU)is configured (first level).
1.3.6.1.4.1.485.3.6.5.1.1.2	ColumnasyncPuConfigAddress	read-only	mandatory	The PU address in the range of 0x00 to 0xfe.
1.3.6.1.4.1.485.3.6.5.1.1.3	ColumnasyncPuNAUName	read-only	mandatory	The NAU name of this PU. The default value for this field is all blank (filled with ASCII space 0x20 characters).
1.3.6.1.4.1.485.3.6.5.1.1.4	ColumnasyncPuInitialState	read-only	mandatory	The initial state of the PU. If configured for 'in-service', then the async PU will be brougt up automattically when the unit is powered up. If configured for …
1.3.6.1.4.1.485.3.6.5.1.1.5	ColumnasyncPuXID	read-only	mandatory	The XID value for this PU. The XID is used to identify the PU during the LLC connection process to the remote Host or Gateway. If the field is configured to 0 …
1.3.6.1.4.1.485.3.6.5.1.1.6	ColumnasyncPuConnectionID	read-only	mandatory	This entry defines the Connection ID to a corresponding entry in the mapping table. The default value for this field is all zeroes.
1.3.6.1.4.1.485.3.6.5.1.1.7	ColumnasyncPuConnectType	read-only	mandatory	The Async PU Connection type.
1.3.6.1.4.1.485.3.6.5.1.1.8	ColumnasyncPuDeviceRangeLow	read-only	mandatory	The device range number low specifies the low number of a range one or more device addresses for which the data to be routed via the connection information (i.…
1.3.6.1.4.1.485.3.6.5.1.1.9	ColumnasyncPuDeviceRangeHigh	read-only	mandatory	The device range number high specifies the high number of a range of one or more device addresses for which the data to be routed via the connection informatio…
1.3.6.1.4.1.485.3.6.5.2	TableasyncPuStatsTable	not-accessible	mandatory	A list of PU statistics entries.
1.3.6.1.4.1.485.3.6.5.2.1	RowasyncPuStatsEntry	not-accessible	mandatory	This entry contains information about a given PU. The entry is indexed by the port number and the PU number.
1.3.6.1.4.1.485.3.6.5.2.1.1	ColumnasyncPuStatsLineIndex	read-only	mandatory	The port number for which PU is configured on.
1.3.6.1.4.1.485.3.6.5.2.1.2	ColumnasyncPuStatsAddress	read-only	mandatory	The PU address in the range of 0x00 to 0xfe.
1.3.6.1.4.1.485.3.6.5.2.1.3	ColumnasyncPuInChars	read-only	mandatory	The number of characters received for this PU.
1.3.6.1.4.1.485.3.6.5.2.1.4	ColumnasyncPuOutChars	read-only	mandatory	The number of characters transmitted to this PU.
1.3.6.1.4.1.485.3.6.5.2.1.5	ColumnasyncPuInMessages	read-only	mandatory	The number of messages received from this PU.
1.3.6.1.4.1.485.3.6.5.2.1.6	ColumnasyncPuOutMessages	read-only	mandatory	The number of messages transmitted to this PU.
1.3.6.1.4.1.485.3.6.6	NodepuLanGroup
1.3.6.1.4.1.485.3.6.6.1	TablelanPuConfigTable	not-accessible	mandatory	A list of PU entries.
1.3.6.1.4.1.485.3.6.6.1.1	RowlanPuConfigEntry	not-accessible	mandatory	This entry contains information about a given PU. The entry is indexed by the port number and the PU number.
1.3.6.1.4.1.485.3.6.6.1.1.1	ColumnlanPuConfigLineIndex	read-only	mandatory	The port number for which the line (CU)is configured (first level).
1.3.6.1.4.1.485.3.6.6.1.1.2	ColumnlanPuConfigAddress	read-only	mandatory	The PU address in the range of 0x00 to 0xff.
1.3.6.1.4.1.485.3.6.6.1.1.3	ColumnlanPuNAUName	read-only	mandatory	The NAU name of this PU. The default value for this field is all blank (filled with ASCII space 0x20 characters).
1.3.6.1.4.1.485.3.6.6.1.1.4	ColumnlanPuXID	read-only	mandatory	The XID value for this PU. The XID is used to identify the PU during the LLC connection process to the remote Host or Gateway. If the field is configured to 0 …
1.3.6.1.4.1.485.3.6.6.1.1.5	ColumnlanPuConnectionID	read-only	mandatory	This entry defines the Connection ID to a corresponding entry in the mapping table. The default value for this field is all zeroes.
1.3.6.1.4.1.485.3.6.6.1.1.6	ColumnlanPuSourceSAP	read-only	mandatory	The LLC source SAP value for this PU. Typically the source SAP will vary for each PU. This is due to the fact that most Sync products are configured to always …
1.3.6.1.4.1.485.3.6.6.1.1.7	ColumnlanPuDestinationSAP	read-only	mandatory	The LLC Destination SAP value for this PU. For SNA typically the destination is almost always SAP 4. However both Host Front Ends (e.g. 3745) or Gateways (e.g.…
1.3.6.1.4.1.485.3.6.6.1.1.8	ColumnlanPuMAC	read-only	mandatory	The LAN Destination MAC address used in the LLC Type 2 connection for this PU. The Token-Ring format for this field is a 6 octet (48 bit) field represented in …
1.3.6.1.4.1.485.3.6.6.1.1.9	ColumnlanPuAlternateMACAddress	read-only	mandatory	Specifies the second destination MAC address for a disaster recovery site.
1.3.6.1.4.1.485.3.6.7	NodepuRemoteGroup
1.3.6.1.4.1.485.3.6.7.1	TableremotePuConfigTable	not-accessible	mandatory	A list of PU mapping entries.
1.3.6.1.4.1.485.3.6.7.1.1	RowremotePuConfigEntry	not-accessible	mandatory	This entry contains information about a given mapping PU. Each entry includes MAC/SAP information for a source PU and a similar information for the partner (ma…
1.3.6.1.4.1.485.3.6.7.1.1.1	ColumnaccessPuConfigLineIndex	read-only	mandatory	The port number for which PU is associated with. Port number 99 is a special value which is used to indicate NetView PU.
1.3.6.1.4.1.485.3.6.7.1.1.2	ColumnaccessPuConfigAddress	read-only	mandatory	The PU address in the range of 0x01 to 0xfe. If the accessPuConfigLineIndex indicates a NetView PU then 01 is used to indicate the primary NetView PU and 02 is…
1.3.6.1.4.1.485.3.6.7.1.1.3	ColumnremotePuConfigLineIndex	read-only	mandatory	The port number for which an access PU, LCU or XCU is associated with.
1.3.6.1.4.1.485.3.6.7.1.1.4	ColumnremotePuConfigAddress	read-only	mandatory	The access PU, LCU or XCU address in the range of 0x01 to 0xfe.
1.3.6.1.4.1.485.3.6.7.1.1.5	ColumnremotePuSourceSAP	read-only	mandatory	The LLC source SAP value for this PU. Typically the source SAP will vary for each PU. This is due to the fact that most Sync products are configured to always …
1.3.6.1.4.1.485.3.6.7.1.1.6	ColumnremotePuDestinationSAP	read-only	mandatory	The LLC Destination SAP value for this PU. For SNA typically the destination is almost always SAP 4. However both Host Front Ends (e.g. 3745) or Gateways (e.g.…
1.3.6.1.4.1.485.3.6.7.1.1.7	ColumnremotePuMAC	read-only	mandatory	The LAN Destination MAC address used in the LLC Type 2 connection for this PU. The Token-Ring format for this field is a 6 octet (48 bit) field represented in …
1.3.6.1.4.1.485.3.6.7.1.1.8	ColumnremotePuPrimaryDLCI	read-only	mandatory	The Frame Relay DLCI used in the LLC Type 2 connection for this PU. The Frame Relay format for this field is a 2 octet (16 bit) field represented in BCD format…
1.3.6.1.4.1.485.3.6.7.1.1.9	ColumnremotePuParallelDLCI	read-only	mandatory	Specifies a parallel DLCI indicating a virtual route in parallel to the primary DLCI path. The parallel virtual route allows for session resiliency.
1.3.6.1.4.1.485.3.6.7.1.1.10	ColumnremotePuAlternateDLCI	read-only	mandatory	Specifies an alternate DLCI indicating a virtual route to a disaster recovery site.
1.3.6.1.4.1.485.3.6.7.1.1.11	ColumnremotePuAlternateMACAddress	read-only	mandatory	Specifies an alternate MAC address indicating a virtual route to a disaster recovery site.
1.3.6.1.4.1.485.3.6.7.1.1.12	ColumnremotePuTransmitPriority	read-only	mandatory	Specifies the transmission priority being URGENT, HIGH, MEDIUM or LOW for this PU.
1.3.6.1.4.1.485.3.6.7.1.1.13	ColumnremotePuBroadcastAllDLCI	read-only	mandatory	If this field is set to YES, after all specified paths are determined as unavailable, the session request is broadcast to all DLCIs. IF the primary DLCI is set…
1.3.6.1.4.1.485.3.6.7.1.1.14	ColumnremotePuLocalDTE	read-only	mandatory	Specifies the local DTE address to match against any in-dial session for an access PU or LAN PU. For non X25 network type, this field is set to 0
1.3.6.1.4.1.485.3.6.7.1.1.15	ColumnremotePuRemoteDTE	read-only	mandatory	Specifies the remote DTE address that the X25 SVC connection uses for this access PU or LAN PU.
1.3.6.1.4.1.485.3.6.8	NodepuX25Group
1.3.6.1.4.1.485.3.6.8.1	Tablex25PuConfigTable	not-accessible	mandatory	A list of PU entries.
1.3.6.1.4.1.485.3.6.8.1.1	Rowx25PuConfigEntry	not-accessible	mandatory	This entry contains information about a given PU. The entry is indexed by the port number and the PU number.
1.3.6.1.4.1.485.3.6.8.1.1.1	Columnx25PuConfigLineIndex	read-only	mandatory	The port number for which PU is configured on.
1.3.6.1.4.1.485.3.6.8.1.1.2	Columnx25PuConfigAddress	read-only	mandatory	The PU address in the range of 0x00 to 0xfe.
1.3.6.1.4.1.485.3.6.8.1.1.3	Columnx25PuNAUName	read-only	mandatory	The NAU name of this PU. The default value for this field is all blank (filled with ASCII space 0x20 characters).
1.3.6.1.4.1.485.3.6.8.1.1.4	Columnx25PuConnectionID	read-only	mandatory	This entry defines the Connection ID to a corresponding entry in the mapping table. The default value for this field is all zeroes.
1.3.6.1.4.1.485.3.6.8.1.1.5	Columnx25PuXID	read-only	mandatory	The XID value for this PU. The XID set the CU identification used to establish and negotiate PU-application sessions. If the PU cannot respond to an XID reques…
1.3.6.1.4.1.485.3.6.8.1.1.6	Columnx25PuSolicitXID	read-only	mandatory	This parameter enables or disables soliciting an XID exchange between the Host and DSPU. This determines whether the Sync unit will solicit an XID to the X.25-…
1.3.6.1.4.1.485.3.6.8.1.1.7	Columnx25PuSourceAddress	read-only	mandatory	The paramter specifies the Source Address. This is used to match DTE address.
1.3.6.1.4.1.485.3.6.8.1.1.8	Columnx25PuRemoteDTEAddress	read-only	mandatory	The paramter specifies a DTE address on the connection's remote end enabling the Host to initiate a session. If you would rather have the X.25 PU initiate the …
1.3.6.1.4.1.485.3.6.9	NodepuAlcGroup
1.3.6.1.4.1.485.3.6.9.1	TablealcPuConfigTable	not-accessible	mandatory	A list of PU entries.
1.3.6.1.4.1.485.3.6.9.1.1	RowalcPuConfigEntry	not-accessible	mandatory	This entry contains information about a given PU. The entry is indexed by the port number and the PU number.
1.3.6.1.4.1.485.3.6.9.1.1.1	ColumnalcPuConfigLineIndex	read-only	mandatory	The port number for which PU is configured on.
1.3.6.1.4.1.485.3.6.9.1.1.2	ColumnalcPuConfigAddress	read-only	mandatory	The PU address in the range of 0x01 to 0x3C (both inclusive) with addresses 0x0d, 0x1D and 0x20 being invalid addresses. The default value is 0x01
1.3.6.1.4.1.485.3.6.9.1.1.3	ColumnalcPuNAUName	read-only	mandatory	The NAU name of this PU. The default value for this field is all blank (filled with ASCII space 0x20 characters).
1.3.6.1.4.1.485.3.6.9.1.1.4	ColumnalcPuCSS	read-only	mandatory	The initial state of the CU. The Interchange (CU) should be enabled or not when the configuration is activated. The range is 'in-service' or 'out-of-service'. …
1.3.6.1.4.1.485.3.6.9.1.1.5	ColumnalcPuConnectionID	read-only	mandatory	This entry defines the Connection ID to a corresponding entry in the mapping table. The default value for this field is all zeroes.
1.3.6.1.4.1.485.3.6.9.1.1.6	ColumnalcPuXID	read-only	mandatory	The XID value for this PU. The XID defines an identifier call ID BLOCK and ID NUM, which is used in session establishment using LLC2. The default value for thi…
1.3.6.1.4.1.485.3.6.9.1.1.7	ColumnalcPuConnectType	read-only	mandatory	The Alc PU Connection type.
1.3.6.1.4.1.485.3.6.9.1.1.8	ColumnalcPuLineNumber	read-only	mandatory	The parmater defines a host reference to as line number. The range of this parameter is 0x01 to 0xFF(both inclusive). This parameter must match the Host config…
1.3.6.1.4.1.485.3.6.9.1.1.9	ColumnalcPuMaximumFastPoll	read-only	mandatory	This parameter defines the maximum time the unit will wait before it polls a device. Typicall the data transfer has priority over polling algorithm. This param…
1.3.6.1.4.1.485.3.6.9.1.1.10	ColumnalcPuMinimumFastPoll	read-only	mandatory	This parameter defines the minimum time the unit will wait before it polls a device. This parameter ensures that the devices are not polled at a very high rate…
1.3.6.1.4.1.485.3.6.9.1.1.11	ColumnalcPuMaximumSlowPollInterval	read-only	mandatory	This parameter defines the maximum time an inactive device is left out of poll list before it is put back in the poll list. Range of this parameter is from 1 t…
1.3.6.1.4.1.485.3.6.9.1.1.12	ColumnalcPuMinimumSlowPollInterval	read-only	mandatory	This parameter defines the minimum time an inactive device is left out of poll list before it is put back in the poll list. Range of this parameter is from 1 t…
1.3.6.1.4.1.485.3.6.9.1.1.13	ColumnalcPuResponseTimeout	read-only	mandatory	This parameter defines the duration that a unit will wait for a response from a device. Range of this parameter is from 1 through 99 in 10ths of a second. The …
1.3.6.1.4.1.485.3.6.9.1.1.14	ColumnalcPuUserData	read-only	mandatory	The paramter specifies the user data upto sixteen hexadecimal bytes for AX.25 protocol.
1.3.6.1.4.1.485.3.6.9.1.1.15	ColumnalcSourceDTEAddress	read-only	mandatory	This parameter specifies the DTE address this port will use to access the Alc network.
1.3.6.1.4.1.485.3.6.9.1.1.16	ColumnalcDestinationDTEAddress	read-only	mandatory	This parameter specifies the DTE address this port will use to access the Alc network.
1.3.6.1.4.1.485.3.6.9.2	TablealcPuStatsTable	not-accessible	mandatory	A list of PU statistics entries.
1.3.6.1.4.1.485.3.6.9.2.1	RowalcPuStatsEntry	not-accessible	mandatory	This entry contains information about a given PU. The entry is indexed by the port number and the PU number.
1.3.6.1.4.1.485.3.6.9.2.1.1	ColumnalcPuStatsLineIndex	read-only	mandatory	The port number for which PU is configured on.
1.3.6.1.4.1.485.3.6.9.2.1.2	ColumnalcPuStatsAddress	read-only	mandatory	The PU address in the range of 0x00 to 0xfe.
1.3.6.1.4.1.485.3.6.9.2.1.3	ColumnalcPuPolls	read-only	mandatory	The number of Polls.
1.3.6.1.4.1.485.3.6.9.2.1.4	ColumnalcPuDeviceFaults	read-only	mandatory	The number of Device Faults.
1.3.6.1.4.1.485.3.6.9.2.1.5	ColumnalcPuBytesRcv	read-only	mandatory	The number of Bytes Received to this PU.
1.3.6.1.4.1.485.3.6.9.2.1.6	ColumnalcPuBytesXmit	read-only	mandatory	The number of Bytes Transmitted for this PU.
1.3.6.1.4.1.485.3.6.9.2.1.7	ColumnalcPuSegRcv	read-only	mandatory	The number of Segments Received to this PU.
1.3.6.1.4.1.485.3.6.9.2.1.8	ColumnalcPuSegXmit	read-only	mandatory	The number of Segments Transmitted for this PU.
1.3.6.1.4.1.485.3.6.10	NodepuBisyncRjeGroup
1.3.6.1.4.1.485.3.6.10.1	TablebisyncrjePuConfigTable	not-accessible	mandatory	A list of Bisync CU entries.
1.3.6.1.4.1.485.3.6.10.1.1	RowbisyncrjePuConfigEntry	not-accessible	mandatory	This entry contains information about a given PU. The entry is indexed by the port number and the PU number.
1.3.6.1.4.1.485.3.6.10.1.1.1	ColumnbisyncrjePuConfigLineIndex	read-only	mandatory	The port number for which PU is configured on.
1.3.6.1.4.1.485.3.6.10.1.1.2	ColumnbisyncrjePuConfigAddress	read-only	mandatory	The PU address in the range of 0x00 to 0xfe.
1.3.6.1.4.1.485.3.6.10.1.1.3	ColumnbisyncrjePuNAUName	read-only	mandatory	The NAU name of this PU. The default value for this field is all blank (filled with ASCII space 0x20 characters).
1.3.6.1.4.1.485.3.6.10.1.1.4	ColumnbisyncrjePuInitialState	read-only	mandatory	The initial state of the PU. If configured for 'in-service', then the Bisync RJE PU will be brougt up automattically when the unit is powered up. If configured…
1.3.6.1.4.1.485.3.6.10.1.1.5	ColumnbisyncrjePuConnectionID	read-only	mandatory	This entry defines the Connection ID to a corresponding entry in the mapping table. The default value for this field is all zeroes.
1.3.6.1.4.1.485.3.6.10.1.1.6	ColumnbisyncrjePuXID	read-only	mandatory	The XID value for this PU. The default value for this field is all zeroes.
1.3.6.1.4.1.485.3.6.10.1.1.7	ColumnbisyncrjePuConnectType	read-only	mandatory	The Bisync RJE PU Connection type.
1.3.6.1.4.1.485.3.7	NodenodeDeviceGroup
1.3.6.1.4.1.485.3.7.1	NodedeviceControlGroup
1.3.6.1.4.1.485.3.7.1.1	TabledeviceControlTable	not-accessible	mandatory	A table for controlling devices and obtaining information.
1.3.6.1.4.1.485.3.7.1.1.1	RowdeviceControlEntry	not-accessible	mandatory	An entry consisting of device information for a particular device.
1.3.6.1.4.1.485.3.7.1.1.1.1	ColumndeviceControlIndex	read-only	mandatory	The number that uniquely identifies this device.
1.3.6.1.4.1.485.3.7.1.1.1.2	ColumndeviceControlCUIndex	read-only	mandatory	The CU index for this device.
1.3.6.1.4.1.485.3.7.1.1.1.3	ColumndeviceControlAddress	read-only	mandatory	The device address.
1.3.6.1.4.1.485.3.7.1.1.1.4	ColumndeviceStatus	read-write	mandatory	The status of the device. To change (write) status of a device, enable, disable, restart or enable all may be set. Valid Return (read) status are enable(d), di…
1.3.6.1.4.1.485.3.7.1.1.1.5	ColumndeviceControlFailureCode	read-only	mandatory	This entry contains the failure codes if the associated device is in the failed state.
1.3.6.1.4.1.485.3.7.2	NodedeviceBSCGroup
1.3.6.1.4.1.485.3.7.2.1	TabledeviceConfigTable	not-accessible	mandatory	A list of device entries.
1.3.6.1.4.1.485.3.7.2.1.1	RowdeviceConfigEntry	not-accessible	mandatory	This entry contains information about a given device. The entry is indexed by the port number, CU index, and device.
1.3.6.1.4.1.485.3.7.2.1.1.1	ColumndeviceConfigLineIndex	read-only	mandatory	The port number for which the line (CU)is configured (line level).
1.3.6.1.4.1.485.3.7.2.1.1.2	ColumndeviceConfigCUIndex	read-only	mandatory	The CU index which this device is configured on (CU level).
1.3.6.1.4.1.485.3.7.2.1.1.3	ColumndeviceConfigAddress	read-only	mandatory	The device address in the legal range of BSC poll addresses (device level).
1.3.6.1.4.1.485.3.7.2.1.1.4	ColumndeviceConfigType	read-only	mandatory	The device type. The default value is crt.
1.3.6.1.4.1.485.3.7.2.2	TabledeviceStatsTable	not-accessible	mandatory	A table of device statistics information.
1.3.6.1.4.1.485.3.7.2.2.1	RowdeviceStatsEntry	not-accessible	mandatory	This entry contains information about a given device. The entry is indexed by the port number, CU index, and device.
1.3.6.1.4.1.485.3.7.2.2.1.1	ColumnbscDeviceLineIndex	read-only	mandatory	The port number for which the line (CU)is configured (line level).
1.3.6.1.4.1.485.3.7.2.2.1.2	ColumnbscDeviceCUIndex	read-only	mandatory	The CU index which this device is configured on (CU level).
1.3.6.1.4.1.485.3.7.2.2.1.3	ColumnbscDeviceAddress	read-only	mandatory	The device address in the legal range of BSC poll addresses (device level).
1.3.6.1.4.1.485.3.7.2.2.1.4	ColumnbscDeviceInTransactions	read-only	mandatory	The number of device receiving transactions.
1.3.6.1.4.1.485.3.7.2.2.1.5	ColumnbscDeviceOutTransactions	read-only	mandatory	The number of device transmitting transactions.
1.3.6.1.4.1.485.3.7.2.2.1.6	ColumnbscDeviceSumCount	read-only	mandatory	The device sum count.
1.3.6.1.4.1.485.3.7.2.2.1.7	ColumnbscDeviceResponseDelaySum	read-only	mandatory	The device sum count.
1.3.6.1.4.1.485.3.7.2.2.1.8	ColumnbscDeviceResponseDelaySqSum	read-only	mandatory	The device sum count.
1.3.6.1.4.1.485.3.7.3	NodedeviceALCGroup
1.3.6.1.4.1.485.3.7.3.1	TablealcdeviceConfigTable	not-accessible	mandatory	A list of device entries.
1.3.6.1.4.1.485.3.7.3.1.1	RowalcdeviceConfigEntry	not-accessible	mandatory	This entry contains information about a given device. The entry is indexed by the port number, CU index, and device.
1.3.6.1.4.1.485.3.7.3.1.1.1	ColumnalcdeviceConfigLineIndex	read-only	mandatory	The port number for which the line (CU)is configured (line level).
1.3.6.1.4.1.485.3.7.3.1.1.2	ColumnalcdeviceConfigCUIndex	read-only	mandatory	The CU index which this device is configured on (CU level).
1.3.6.1.4.1.485.3.7.3.1.1.3	ColumnalcdeviceConfigAddress	read-only	mandatory	The device address in the legal range of ALC poll addresses (device level). The range is 0x01 to 0x3c with 0x20 being invalid address. The default value is 0x0…
1.3.6.1.4.1.485.3.7.3.1.1.4	ColumnalcdeviceConfigType	read-only	mandatory	The device type. The default value is printer.
1.3.6.1.4.1.485.3.8	NodenodeT7Group
1.3.6.1.4.1.485.3.8.1	Nodet7ConfigGroup
1.3.6.1.4.1.485.3.8.1.1	Tablet7ConfigTable	not-accessible	mandatory	A table for T7 protocol configuration parameters.
1.3.6.1.4.1.485.3.8.1.1.1	Rowt7ConfigEntry	not-accessible	mandatory	An entry consisting of T7 protocol information for a particular port.
1.3.6.1.4.1.485.3.8.1.1.1.1	Columnt7ConfigIndex	read-only	mandatory	The number that uniquely identifies this T7 port.
1.3.6.1.4.1.485.3.8.1.1.1.2	Columnt7ProtocolEnabled	read-only	mandatory	This flag indicates if T7 protocol is enabled on this unit. If No, the following T7 variables will have no effect. The default value for this field is 'No'
1.3.6.1.4.1.485.3.8.1.1.1.3	Columnt7PortSpeed	read-only	mandatory	The speed of the T7 port expressed in bits per second. The default speed is 75 bits per second
1.3.6.1.4.1.485.3.8.1.1.1.4	Columnt7StopBits	read-only	mandatory	Number of stop bits generated for T7 port transmit characters (received characters may have any number of bits regardless of the configuration). The default va…
1.3.6.1.4.1.485.3.8.1.1.1.5	Columnt7PortParity	read-only	mandatory	T7 port parity type generated for transmit characters and checked for receive characters. If ODD or EVEN, then if a character is received with invalid parity, …
1.3.6.1.4.1.485.3.8.1.1.1.6	Columnt7DataBits	read-only	mandatory	T7 port number of data bit (not including the parity bit). The default value is 7
1.3.6.1.4.1.485.3.8.1.1.1.7	Columnt7IdleTimer	read-only	mandatory	The T7 Idle timer is amount of time (in milliseconds) used to determine when a complete message has been received from the line. If configured as 0, then this …
1.3.6.1.4.1.485.3.8.1.1.1.8	Columnt7PortTxFrameGap	read-only	mandatory	The T7 port TX frame gap is analogous to the idle timer, but is used to separate messages received from the network by gaps in time so that the Async device ca…
1.3.6.1.4.1.485.3.8.1.1.1.9	Columnt7RxForwardingCount	read-only	mandatory	The T7 port receive forwarding count is used to forward messages when a configured number of characters is received from the Async line. This must be configure…
1.3.6.1.4.1.485.3.8.1.1.1.10	Columnt7PortIPAddress	read-only	mandatory	The T7 port IP address is used to configure the remote IP address in which to communicate with.
1.3.6.1.4.1.485.3.8.1.1.1.11	Columnt7UDPPortNumber	read-only	mandatory	The T7 port UDP port number address is used to configure the local and remot UDP port number (i.e. socket) address in which to communicate with. The default va…
1.3.6.1.4.1.485.3.8.2	Nodet7StatsGroup
1.3.6.1.4.1.485.3.8.2.1	Tablet7StatsTable	not-accessible	mandatory	A table of T7 protocol statistics information.
1.3.6.1.4.1.485.3.8.2.1.1	Rowt7StatsEntry	not-accessible	mandatory	This entry contains information about a T7 port. The entry is indexed by the port number, CU index, and device.
1.3.6.1.4.1.485.3.8.2.1.1.1	Columnt7StatsIndex	read-only	mandatory	The number that uniquely identifies this T7 port.
1.3.6.1.4.1.485.3.8.2.1.1.2	Columnt7InOctets	read-only	mandatory	The number of bytes received.
1.3.6.1.4.1.485.3.8.2.1.1.3	Columnt7OutOctets	read-only	mandatory	The number of bytes sent.
1.3.6.1.4.1.485.3.8.2.1.1.4	Columnt7InMessages	read-only	mandatory	The number of messages received.
1.3.6.1.4.1.485.3.8.2.1.1.5	Columnt7OutMessages	read-only	mandatory	The number of messages sent.
1.3.6.1.4.1.485.3.8.2.1.1.6	Columnt7InMsgDiscarded	read-only	mandatory	The number of received messages discarded.
1.3.6.1.4.1.485.3.8.2.1.1.7	Columnt7OutMsgDiscarded	read-only	mandatory	The number of sent messages discarded.
1.3.6.1.4.1.485.3.8.2.1.1.8	Columnt7XmtFailures	read-only	mandatory	The number of failures in transmission.
1.3.6.1.4.1.485.3.8.2.1.1.9	Columnt7RcvMsgForwarded	read-only	mandatory	The number of received messages forwarded.
1.3.6.1.4.1.485.3.8.2.1.1.10	Columnt7RcvMsgErrors	read-only	mandatory	The number of errors detected in receiving messages.
1.3.6.1.4.1.485.3.8.2.1.1.11	Columnt7RcvCharsDiscarded	read-only	mandatory	The number of received characters discarded.
1.3.6.1.4.1.485.3.8.2.1.1.12	Columnt7RcvParityErrors	read-only	mandatory	The number of parity errors detected.
1.3.6.1.4.1.485.3.8.2.1.1.13	Columnt7RcvFramingErrors	read-only	mandatory	The number of errors detected in receiving frames.
1.3.6.1.4.1.485.3.8.2.1.1.14	Columnt7RcvFifoOverruns	read-only	mandatory	The number FIFO receive overruns detected.
1.3.6.1.4.1.485.3.8.2.1.1.15	Columnt7RcvCharsOverruns	read-only	mandatory	The number of character receive overruns detected.
1.3.6.1.4.1.485.3.8.2.1.1.16	Columnt7RcvBreakConditions	read-only	mandatory	The number of receive break conditions.
1.3.6.1.4.1.485.3.9	NodenodeFrCirGroup
1.3.6.1.4.1.485.3.9.1	TablefrExtCircuitTable	not-accessible	mandatory	A table containing information about specific Data Link Connection Identifiers and corresponding virtual circuits.
1.3.6.1.4.1.485.3.9.1.1	RowfrExtCircuitEntry	not-accessible	mandatory	The information regarding a single Data Link Connection Identifier.
1.3.6.1.4.1.485.3.9.1.1.1	ColumnfrExtCircuitIfIndex	read-only	mandatory	The ifIndex Value of the ifEntry this virtual circuit is layered onto.
1.3.6.1.4.1.485.3.9.1.1.2	ColumnfrExtCircuitDlci	read-only	mandatory	The Data Link Connection Identifier for this virtual circuit.
1.3.6.1.4.1.485.3.9.1.1.3	ColumnfrExtCircuitStatusIgnored	read-write	mandatory	This field is used for consolidating status of the unit. The status of this circuit is not put into consideration when consolidating status of the unit if this…
1.3.6.1.4.1.485.3.9.1.1.4	ColumnfrExtCircuitStatusAcknowledged	read-write	mandatory	This field is used for consolidating status of the unit. When this field is set to acknowledge, unit will re-consolidate its status without putting the status …
1.3.6.1.4.1.485.3.9.1.1.5	ColumnfrExtCircuitPartnerId	read-only	mandatory	This is the unit id of the FrameNode at the other end of the Frame relay PVC. It consists of a 1 to 8 octets right justified case-sensitive ASCII field which u…
1.3.6.1.4.1.485.3.9.1.1.6	ColumnfrExtCircuitTxDe	read-only	mandatory	Total number of frames sent with DE bit for this PVC.
1.3.6.1.4.1.485.3.9.1.1.7	ColumnfrExtCircuitRxDe	read-only	mandatory	Total number of frames received with the DE bit for this PVC.
1.3.6.1.4.1.485.3.9.1.1.8	ColumnfrExtCircuitMinBits	read-only	mandatory	Minimum number of bits transmitted in Time Period Tc for this PVC.
1.3.6.1.4.1.485.3.9.1.1.9	ColumnfrExtCircuitMaxBits	read-only	mandatory	Maximum number of bits transmitted in Time Period Tc for this PVC.
1.3.6.1.4.1.485.3.9.1.1.10	ColumnfrExtCircuitQOctets	read-only	mandatory	Number of octets queued for transmission because the maximum burst rate was achieved in Tc. These are the number of octets that had transmission delay until ne…
1.3.6.1.4.1.485.3.10	NodenodeSlipGroup
1.3.6.1.4.1.485.3.10.1	NodeslipConfigGroup
1.3.6.1.4.1.485.3.10.1.1	TableslipConfigTable	not-accessible	mandatory	A table for Slip protocol configuration parameters.
1.3.6.1.4.1.485.3.10.1.1.1	RowslipConfigEntry	not-accessible	mandatory	An entry consisting of Slip protocol information for a particular port.
1.3.6.1.4.1.485.3.10.1.1.1.1	ColumnslipConfigIndex	read-only	mandatory	The number that uniquely identifies this Slip port.
1.3.6.1.4.1.485.3.10.1.1.1.2	ColumnslipProtocolEnabled	read-only	mandatory	This flag indicates if COM2 port is enabled or disabled for usage for SLIP. The default value for this field is 'Yes'
1.3.6.1.4.1.485.3.10.1.1.1.3	ColumnslipPortSpeed	read-only	mandatory	This parameter determines the COM2 port speed for the SLIP connection to the modem. The default speed is 9600 bits per second
1.3.6.1.4.1.485.3.10.1.1.1.4	ColumnslipStopBits	read-only	mandatory	This parameter specifies the number of transmit Stop Bits used on the SLIP connection to the modem. The range of this parameter is 1 or 2 bits. The default val…
1.3.6.1.4.1.485.3.10.1.1.1.5	ColumnslipIdleTimer	read-only	mandatory	The Slip Idle timer is amount of time (in milliseconds) used to determine the end of frame. The idel timer is started every time a character is received. The r…
1.3.6.1.4.1.485.3.10.1.1.1.6	ColumnslipPortIPAddress	read-only	mandatory	The Slip port IP address. The default valus is 0.0.0.0.
1.3.6.1.4.1.485.3.10.1.1.1.7	ColumnslipUsage	read-only	mandatory	This parameter defines whether SLIP protocol is used to manage locally attached modem or is it used for IP end node function or IP forwarding function. The ran…
1.3.6.1.4.1.485.3.10.1.1.1.8	ColumnslipNetworkMask	read-only	mandatory	This parameter defines IP sub-netmask for this parameter. The default valus is 0.0.0.0.
1.3.6.1.4.1.485.3.10.1.1.1.9	ColumnslipDefaultGateway	read-only	mandatory	This parameter defines IP default gateway. The default valus is 0.0.0.0.
1.3.6.1.4.1.485.3.10.1.1.1.10	ColumnslipEnableRIP	read-only	mandatory	This parameter defines whether RIP packets should be sent on this interface or not. Range is yes or no. The default valus is 'no'.
1.3.6.1.4.1.485.3.10.2	NodeslipStatsGroup
1.3.6.1.4.1.485.3.10.2.1	TableslipStatsTable	not-accessible	mandatory	A table of Slip protocol statistics information.
1.3.6.1.4.1.485.3.10.2.1.1	RowslipStatsEntry	not-accessible	mandatory	This entry contains information about a slip Com port.
1.3.6.1.4.1.485.3.10.2.1.1.1	ColumnslipStatsIndex	read-only	mandatory	The number that uniquely identifies this Slip com port.
1.3.6.1.4.1.485.3.10.2.1.1.2	ColumnslipInChrs	read-only	mandatory	The number of Characters received.
1.3.6.1.4.1.485.3.10.2.1.1.3	ColumnslipOutChrs	read-only	mandatory	The number of characters sent.
1.3.6.1.4.1.485.3.10.2.1.1.4	ColumnslipInMessages	read-only	mandatory	The number of messages received.
1.3.6.1.4.1.485.3.10.2.1.1.5	ColumnslipOutMessages	read-only	mandatory	The number of messages sent.
1.3.6.1.4.1.485.3.10.2.1.1.6	ColumnslipInMsgDiscarded	read-only	mandatory	The number of received messages discarded.
1.3.6.1.4.1.485.3.10.2.1.1.7	ColumnslipOutMsgDiscarded	read-only	mandatory	The number of sent messages discarded.
1.3.6.1.4.1.485.3.10.2.1.1.8	ColumnslipXmtFailures	read-only	mandatory	The number of failures in transmission.
1.3.6.1.4.1.485.3.10.2.1.1.9	ColumnslipRcvMsgForwarded	read-only	mandatory	The number of received messages forwarded.
1.3.6.1.4.1.485.3.10.2.1.1.10	ColumnslipRcvMsgErrors	read-only	mandatory	The number of errors detected in receiving messages.
1.3.6.1.4.1.485.3.10.2.1.1.11	ColumnslipRcvCharsDiscarded	read-only	mandatory	The number of received characters discarded.
1.3.6.1.4.1.485.3.10.2.1.1.12	ColumnslipRcvParityErrors	read-only	mandatory	The number of parity errors detected.
1.3.6.1.4.1.485.3.10.2.1.1.13	ColumnslipRcvFramingErrors	read-only	mandatory	The number of errors detected in receiving frames.
1.3.6.1.4.1.485.3.10.2.1.1.14	ColumnslipRcvFifoOverruns	read-only	mandatory	The number FIFO receive overruns detected.
1.3.6.1.4.1.485.3.10.2.1.1.15	ColumnslipRcvCharsOverruns	read-only	mandatory	The number of character receive overruns detected.
1.3.6.1.4.1.485.3.10.2.1.1.16	ColumnslipRcvBreakConditions	read-only	mandatory	The number of receive break conditions.
1.3.6.1.4.1.485.3.11	NodenodeIpxGroup
1.3.6.1.4.1.485.3.11.1	NodeipxConfigGroup
1.3.6.1.4.1.485.3.11.1.1	ScalaripxEnableRouting	read-only	mandatory	This parameter determines whether or not IPX Routing is enabled. Thr range of this parameter is yes or no. If set to yes, the parameter 'Filter IPX' should be …
1.3.6.1.4.1.485.3.11.1.2	ScalaripxRoutedTxPriority	read-only	mandatory	This parameter governs the transmission priority of the routed IPX frames for Frame Relay port(s). The range is URGENT, HIGH, MEDIUM AND LOW. The default is se…
1.3.6.1.4.1.485.3.11.1.3	ScalaripxEnableRipBroadcast	read-only	mandatory	This parameter governs whether the framenode should send RIP packets or not. The range of this parameter is YES or NO. If IPX routing is disabled, this paramet…
1.3.6.1.4.1.485.3.11.1.4	ScalaripxEnableSapBroadcast	read-only	mandatory	This parameter governs whether the framenode should send SAP packets. The range of this parameter is YES or NO. If IPX routing is disabled, this parameter is i…
1.3.6.1.4.1.485.3.11.1.5	ScalaripxEnableNetBIOS	read-only	mandatory	This parameter governs whether the frame Node should process NetBIOS packets or not. The range of this parameter is Yes or No. If IPX Routing is disabled, this…
1.3.6.1.4.1.485.3.11.1.6	ScalaripxGlobalNodeId	read-only	mandatory	By default FrameNode always implements IPX WAN over Frame Relay. The 'timer request' packet is transmitted by the FrameNode over Frame Relay. This packet inclu…
1.3.6.1.4.1.485.3.12	NodenodeIpGroup
1.3.6.1.4.1.485.3.12.1	NodeipConfigGroup
1.3.6.1.4.1.485.3.12.1.1	ScalarpriIPHelperAddress	read-only	mandatory	This is the Primary IP Helper Address of this unit.
1.3.6.1.4.1.485.3.12.1.2	ScalarsecIPHelperAddress	read-only	mandatory	This is the Secondary IP Helper Address of this unit.
1.3.6.1.4.1.485.3.12.1.3	ScalarinternalIPAddr	read-only	mandatory	The range of this parameter and the default value is same as other IP Address in the unit.
1.3.6.1.4.1.485.3.12.1.4	ScalarinternalIPNetmask	read-only	mandatory	This is the Internal IP network mask.
1.3.6.1.4.1.485.3.12.1.5	ScalarenableIpRouting	read-only	mandatory	This is the Internal IP network mask.
1.3.6.1.4.1.485.3.12.1.6	ScalarenableIpBridging	read-only	mandatory	This is the Internal IP network mask.
1.3.6.1.4.1.485.3.12.1.7	ScalarenableRipBroadcast	read-only	mandatory	This is the Internal IP network mask.
1.3.6.1.4.1.485.800	NodeconfigChanged			This trap indicates that the configuration of the unit has been changed.
1.3.6.1.4.1.485.801	NodeconfigError			This trap indicates that the activation of configuration of the unit has resulted in an error. New configuration has not been successfully activated.
1.3.6.1.4.1.485.802	NodedumpExists			This trap indicates that a memory core dump exists.
1.3.6.1.4.1.485.803	NodedumpArchived			This trap indicates that the memory dump file has been archived.
1.3.6.1.4.1.485.804	NodelineStatusChanged			This trap indicates that the indicated Line or Port has changed state. It has either been enabled, failed or disabled.
1.3.6.1.4.1.485.805	NodelanStatusChanged			This trap indicates that the indicated LAN Port has changed state. It has either been enabled, failed or disabled.
1.3.6.1.4.1.485.806	NodelineQuality			This trap indicates that the line quality is changed. If the lineQualityAborts is greater than 5 or lineQualityCRCErrors is greater that 5 then it indicates a …
1.3.6.1.4.1.485.807	NodepuStatusChanged			This trap indicates that the indicated PU has changed state. It has either been enabled, failed or disabled.
1.3.6.1.4.1.485.808	NodepuConnectionStatusChanged			Note this trap is obsolete. This trap indicates that the indicated PU has changed connection state. Its connection has either been established, disconnected, o…
1.3.6.1.4.1.485.809	NodenetviewConnectionStatusChanged			Note this trap is obsolete. This trap indicates that the NetView PU has changed connection state. Its connection has either been established, disconnected, or …
1.3.6.1.4.1.485.810	NodenetviewAltConnectionStatusChanged			Note this trap is obsolete. This trap indicates that the Alternate NetView PU has changed connection state. Its connection has either been established, disconn…
1.3.6.1.4.1.485.811	NodepuConnectionStatusUp			This trap is obsolete. This trap indicates that the indicated PU has changed connection state. Its connection had been established.
1.3.6.1.4.1.485.812	NodepuConnectionStatusDown			This trap is obsolete. This trap indicates that the indicated PU has changed connection state. Its connection has been disconnected. If the indicated PU is not…
1.3.6.1.4.1.485.813	NodenetviewConnectionStatusUp			This trap is obsolete. This trap indicates that the indicated NetView PU has changed connection state. Its connection has been established.
1.3.6.1.4.1.485.814	NodenetviewConnectionStatusDown			This trap is obsolete. This trap indicates that the indicated NetView PU has changed connection state. Its connection had been disconnected. If the indicated P…
1.3.6.1.4.1.485.815	NodenetviewAltConnectionStatusUp			This trap is obsolete. This trap indicates that the indicated Alternate NetView PU has changed connection state. Its connection has been established.
1.3.6.1.4.1.485.816	NodenetviewAltConnectionStatusDown			This trap is obsolete. This trap indicates that the indicated Alternate NetView PU has changed connection state. Its connection had been disconnected. If the i…
1.3.6.1.4.1.485.817	NodesessSwitchedToPrimaryDLCI			This trap indicates that a session switch has occured from a Parallel DLCI to Primary DLCI.
1.3.6.1.4.1.485.818	NodesessSwitchedToParallelDLCI			This trap indicates that a session switch has occured from the Primary DLCI to the Parallel DLCI.
1.3.6.1.4.1.485.819	NodesessUpOnPrimaryDLCI			This indicates that a PU session is established on a primary DLCI. This TRAP is generated for Frame Nodes only. For Conversion Node sessUpOnPrimaryMAC or sessU…
1.3.6.1.4.1.485.820	NodesessUpOnParallelDLCI			This indicates that a PU session is established on a parallel DLCI. This TRAP is generated for Frame Nodes only. For Conversion Node sessUpOnPrimaryMAC or sess…
1.3.6.1.4.1.485.821	NodesessUpOnAlternateDLCI			This indicates that a PU session is established on an alternate DLCI. This TRAP is generated for Frame Nodes only. For Conversion Node sessUpOnPrimaryMAC or se…
1.3.6.1.4.1.485.822	NodesessUpOnPrimaryMAC			This indicates that a PU session is established on a non-explicit (dynamic, or broadcast) DLCI to the primary destination MAC. For Conversion Node, puCurrentDl…
1.3.6.1.4.1.485.823	NodesessUpOnAlternateMAC			This indicates that a PU session is established on a non-explicit (dynamic, or broadcast) DLCI to the alternate destination MAC, if configured. For Conversion …
1.3.6.1.4.1.485.824	NodesessDownOnPrimaryMAC			This trap indicates that the session for the indicated PU associated with the primary destination MAC was cleared. If the indicated PU is not in session, the t…
1.3.6.1.4.1.485.825	NodesessDownOnAlternateMAC			This trap indicates that the session for the indicated PU associated with the alternate destination MAC, if configured, was cleared. If the indicated PU is not…
1.3.6.1.4.1.485.826	NodelostUNI			This trap indicates that the indicated Frame Relay Line or Port has lost its UNI connectivity to the Frame Relay network.
1.3.6.1.4.1.485.827	NoderestoredUNI			This trap indicates that the indicated Frame Relay Line or Port has restored its UNI connectivity to the Frame Relay network.
1.3.6.1.4.1.485.828	NodeswitchedToBackup			This trap indicates that the indicated Frame Relay Line or Port has successfully switched to switched backup connection.
1.3.6.1.4.1.485.829	NodeswitchedToDed			This trap indicates that the indicated Frame Relay Line or Port has successfully switched to the dedicated Frame Relay connection to the network.
1.3.6.1.4.1.485.830	NodedialConnStatusChanged			This trap indicates that the indicated dial backup connection has changed state. It has either been connected or disconnected.
1.3.6.1.4.1.485.831	NodesessUpOnSVC			This trap indicates that the session for the indicated PU or LAN PU associated with the remote DTE address was established.
1.3.6.1.4.1.485.832	NodesessDownOnSVC			This trap indicates that the session for the indicated PU or LAN PU associated with the last remote DTE address was cleared. If the indicated PU/LAN PU is not …

Type Definitions

Name	Syntax	Status	Description
DisplayString	OCTET STRING
PhysAddress	OCTET STRING

MIB Viewer

What's a MIB?

What's SNMP?

What's an OID?

SNMP Fundamentals

Using net-snmp

Configuring SNMP on Cisco devices

Configuring SNMP on Fortinet devices

Understanding MIBs

Troubleshooting SNMP

Searching OIDs

Modem/MTA bootfiles

DOCSIS Monitoring

Linux snmpd passthrough

SYNC-RESEARCH-MIB

Bulk Translate

Search Vendor MIBs

Search Vendor Traps