TCOP-OPT-MIB
77 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | Counter enterprises Gauge |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.449 | Nodecodex | |||
| 1.3.6.1.4.1.449.2 | NodecdxProductSpecific | |||
| 1.3.6.1.4.1.449.2.1 | Nodecdx6500 | |||
| 1.3.6.1.4.1.449.2.1.2 | Nodecdx6500Configuration | |||
| 1.3.6.1.4.1.449.2.1.2.1 | Nodecdx6500CfgProtocolGroup | |||
| 1.3.6.1.4.1.449.2.1.2.1.1 | Nodecdx6500PCTPortProtocolGroup | |||
| 1.3.6.1.4.1.449.2.1.2.1.1.23 | Tablecdx6500PPCTTCOPPortTable | not-accessible | mandatory | This table contains TCOP Port configuration parameters. |
| 1.3.6.1.4.1.449.2.1.2.1.1.23.1 | Rowcdx6500PPCTTCOPPortEntry | not-accessible | mandatory | Each PortEntry contains the configuration parameters for one TCOP port. |
| 1.3.6.1.4.1.449.2.1.2.1.1.23.1.1 | Columncdx6500TCOPCfgPortNumber | read-only | mandatory | Port number of the port being used by TCOP. |
| 1.3.6.1.4.1.449.2.1.2.1.1.23.1.2 | Columncdx6500TCOPCfgSubtype | read-only | mandatory | Select the sub-type for the synchronous protocol running on this port. hsc3 - Transparent Hitachi type gnet - Transparent GNET type. uts - Transparent Uniscope… |
| 1.3.6.1.4.1.449.2.1.2.1.1.23.1.3 | Columncdx6500TCOPCfgClockSource | read-only | mandatory | int - internal clock source ext - external clock source on pins 18 and 24. |
| 1.3.6.1.4.1.449.2.1.2.1.1.23.1.4 | Columncdx6500TCOPCfgClockSpeed | read-only | mandatory | This is the port speed in bits per second, when clock source = int. |
| 1.3.6.1.4.1.449.2.1.2.1.1.23.1.5 | Columncdx6500TCOPCfgContention | read-only | mandatory | Specifies the line contention. hdx - Half duplex, DCD toggles fdx - Full duplex, DCD is always high. |
| 1.3.6.1.4.1.449.2.1.2.1.1.23.1.6 | Columncdx6500TCOPCfgCodeType | read-only | mandatory | Either of ascii or ebcdic code set is used. |
| 1.3.6.1.4.1.449.2.1.2.1.1.23.1.7 | Columncdx6500TCOPCfgReceiveByteCount | read-only | mandatory | Specifies the number of bytes collected from the line before data is forwarded to the network. A minimum byte count constraint is imposed for port speed interv… |
| 1.3.6.1.4.1.449.2.1.2.1.1.23.1.8 | Columncdx6500TCOPCfgCallControl | read-only | mandatory | none - port will generate a call auto - Autocalling enabled. |
| 1.3.6.1.4.1.449.2.1.2.1.1.23.1.9 | Columncdx6500TCOPCfgAutoCallMnem | read-only | mandatory | This mnemonic name is used for Auto calling. |
| 1.3.6.1.4.1.449.2.1.2.1.1.23.1.10 | Columncdx6500TCOPCfgAutoCallTO | read-only | mandatory | Specifies the time in seconds between call attempts when autocalling. |
| 1.3.6.1.4.1.449.2.1.2.1.1.23.1.11 | Columncdx6500TCOPCfgMaxAutoCallTries | read-only | mandatory | Specifies the maximum number of times the TCOP port will attempt to call. A value of 0 will allow unlimited number of attempts. |
| 1.3.6.1.4.1.449.2.1.2.1.1.23.1.12 | Columncdx6500TCOPCfgPortAddress | read-only | mandatory | The BCD address specified here is inserted in the calling address field when the TCOP port makes a call. |
| 1.3.6.1.4.1.449.2.1.2.1.1.23.1.13 | Columncdx6500TCOPCfgProtocolID | read-only | mandatory | The protocol identifier specified here is inserted into a call packet or checked against the identifier of an incoming call. |
| 1.3.6.1.4.1.449.2.1.2.1.1.23.1.14 | Columncdx6500TCOPCfgEnableBill | read-only | mandatory | This controls whether billing (accounting) records will be created for calls on this TCOP port. |
| 1.3.6.1.4.1.449.2.1.2.1.1.23.1.15 | Columncdx6500TCOPCfgRestrictConn | read-only | mandatory | Specifies the destination of all calls routed to from this port, regardless of route selection table entries. For example, to route calls to port 1, use P1. To… |
| 1.3.6.1.4.1.449.2.1.2.1.1.23.1.16 | Columncdx6500TCOPCfgRXQueue | read-only | mandatory | Specifies the maximum number of received messages to be queued. This parameter is effective only when sub-type = gnet. |
| 1.3.6.1.4.1.449.2.1.2.1.1.23.1.17 | Columncdx6500TCOPCfgTXQueue | read-only | mandatory | Specifies the maximum number of transmit messages to be queued. This parameter is effective only when sub-type = gnet. |
| 1.3.6.1.4.1.449.2.1.2.1.1.23.1.18 | Columncdx6500TCOPCfgQueueOverflow | read-only | mandatory | Specifies the action to be taken if the receive message queue overflows. This parameter is effective only when sub-type = gnet. resetConnection - Reset connect… |
| 1.3.6.1.4.1.449.2.1.2.1.1.23.1.19 | Columncdx6500TCOPCfgPortType | read-only | mandatory | The Port Type of the port. |
| 1.3.6.1.4.1.449.2.1.2.1.1.23.1.20 | Columncdx6500TCOPCfgDataTransmission | read-only | mandatory | This determines the mode of data transfer. hdx - Indicates half duplex data transfer. fdx - Indicates full duplex data transfer. |
| 1.3.6.1.4.1.449.2.1.2.1.1.23.1.21 | Columncdx6500TCOPCfgElectricalInterfaceType | read-only | mandatory | Specify the Electrical Interface Type: V.24 - V.24 Electrical Interface Type V.35 - V.35 Electrical Interface Type V.36 - V.36 Electrical Interface Type X.21 -… |
| 1.3.6.1.4.1.449.2.1.2.1.1.23.1.22 | Columncdx6500TCOPCfgV24ElectricalInterfaceOption | read-only | mandatory | Specify the Pin 22 option: RI - V.24 uses Pin 22 for Ring Indicator output signal TM - V.24 uses Pin 22 for Test Mode input signal |
| 1.3.6.1.4.1.449.2.1.2.1.1.23.1.23 | Columncdx6500TCOPCfgHighSpeedElectricalInterfaceOption | read-only | mandatory | Specify the cable type: NONE - V.35/V.36/X.21 DCE with straight through cable XOVER - V.35/V.36/X.21 DCE with crossover adapter cable |
| 1.3.6.1.4.1.449.2.1.3 | Nodecdx6500Statistics | |||
| 1.3.6.1.4.1.449.2.1.3.1 | Nodecdx6500StatProtocolGroup | |||
| 1.3.6.1.4.1.449.2.1.3.1.1 | Nodecdx6500PSTPortProtocolGroup | |||
| 1.3.6.1.4.1.449.2.1.3.1.1.24 | Tablecdx6500PPSTTCOPPortTable | not-accessible | mandatory | This table holds statistics items for TCOP ports. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1 | Rowcdx6500PPSTTCOPPortEntry | not-accessible | mandatory | This entry holds the statistics items for one TCOP port. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.1 | Columncdx6500TCOPStatPortNumber | read-only | mandatory | The port number for this TCOP entry. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.2 | Columncdx6500TCOPStatPortType | read-only | mandatory | The configured value of the Port Type. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.3 | Columncdx6500TCOPStatPortSubtype | read-only | mandatory | Access protocol for this port. hsc3 - Transparent Hitachi type gnet - Transparent GNET type. uts - Transparent Uniscope type. slc - Synchronous Link Control. a… |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.4 | Columncdx6500TCOPStatPortStatus | read-only | mandatory | Status of this port: Up : Port is enabled Down : Port is Inactive Disabled : Port is disabled. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.5 | Columncdx6500TCOPStatPortState | read-only | mandatory | Current port state: discPhase - Disconnect phase, no call in place callingPhase - Port has initiated Autocall calledPhase - Port has received a call request co… |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.6 | Columncdx6500TCOPStatPortSpeed | read-only | mandatory | The measured port speed in bits per second. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.7 | Columncdx6500TCOPStatPortUtilIn | read-only | mandatory | Percentage of port bandwidth in use. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.8 | Columncdx6500TCOPStatPortUtilOut | read-only | mandatory | Percentage of port bandwidth in use. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.9 | Columncdx6500TCOPStatPortOverrunErrs | read-only | mandatory | Total number of overrun errors counted by the I/O driver since the last node or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.10 | Columncdx6500TCOPStatPortUnderrunErrs | read-only | mandatory | Total number of underrun errors counted by the I/O driver since the last node or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.11 | Columncdx6500TCOPStatPortBCCErrs | read-only | mandatory | Total number of CRC errors counted by the I/O driver since the last node or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.12 | Columncdx6500TCOPStatPortParityErrs | read-only | mandatory | Total number of parity errors counted by the I/O driver since the last node or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.13 | Columncdx6500TCOPStatPortInChars | read-only | mandatory | Number of characters received since last node, port or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.14 | Columncdx6500TCOPStatPortOutChars | read-only | mandatory | Number of characters sent since last node, port or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.15 | Columncdx6500TCOPStatPortInCharsRate | read-only | mandatory | Average number of characters received per second since last node, port or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.16 | Columncdx6500TCOPStatPortOutCharsRate | read-only | mandatory | Average number of characters sent per second since last node, port or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.17 | Columncdx6500TCOPStatPortInMessages | read-only | mandatory | Number of messages received since last node, port or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.18 | Columncdx6500TCOPStatPortOutMessages | read-only | mandatory | Number of messages sent since last node, port or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.19 | Columncdx6500TCOPStatPortInMessagesRate | read-only | mandatory | Average number of messages received per second since last node, port or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.20 | Columncdx6500TCOPStatPortOutMessagesRate | read-only | mandatory | Average number of messages sent per second since last node, port or statistics reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.21 | Columncdx6500TCOPStatPortInPktsQueued | read-only | mandatory | Number of received packets which are currently queued. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.22 | Columncdx6500TCOPStatPortOutPktsQueued | read-only | mandatory | Number of packets currently queued which are to be sent. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.23 | Columncdx6500TCOPStatPortMaxInQueueLength | read-only | mandatory | The maximum queue length reached for incoming packets since the last reset. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.24 | Columncdx6500TCOPStatPortMaxOutQueueLength | read-only | mandatory | The maximum queue length reached since the last reset, for packets to be sent. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.25 | Columncdx6500TCOPStatPortPktQueueFlushCount | read-only | mandatory | The number of times the receive queue is flushed. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.26 | Columncdx6500TCOPStatAutoCallStatus | read-only | mandatory | Current status of the autocall. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.27 | Columncdx6500TCOPStatAutoCallNextAttempt | read-only | mandatory | Time in seconds until next autocall attempt. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.28 | Columncdx6500TCOPStatAutoCallAttemptCount | read-only | mandatory | Number of autocall attempts. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.29 | Columncdx6500TCOPStatAutoCallLastClearCause | read-only | mandatory | Last autocall clear cause code dte - Cleared by other end np - Destination not obtainable occ - Called number busy nc - Network congested inv - Invalid facilit… |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.30 | Columncdx6500TCOPStatAutoCallLastClearDiagnosis | read-only | mandatory | Last clear diagnostic code none - No more information bps - Invalid P(S) bpr - Invalid P(R) ptinv - Packet type invalid pna - Packet not allowed psh - Packet t… |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.31 | Columncdx6500TCOPStatAutoCallLastInCalledAddress | read-only | mandatory | X25 called address in BCD format of last inbound call. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.32 | Columncdx6500TCOPStatAutoCallLastInCallingAddress | read-only | mandatory | X25 calling address in BCD format of last inbound call. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.33 | Columncdx6500TCOPStatAutoCallLastInCallFacilities | read-only | mandatory | X25 facilities of inbound call. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.34 | Columncdx6500TCOPStatAutoCallLastInCallCUD | read-only | mandatory | X25 Call User Data of inbound call. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.35 | Columncdx6500TCOPStatAutoCallLastOutCalledAddress | read-only | mandatory | X25 called address in BCD format of last outbound call. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.36 | Columncdx6500TCOPStatAutoCallLastOutCallingAddress | read-only | mandatory | X25 calling address in BCD format of last outbound call. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.37 | Columncdx6500TCOPStatAutoCallLastOutCallFacilities | read-only | mandatory | X25 facilities of outbound call. |
| 1.3.6.1.4.1.449.2.1.3.1.1.24.1.38 | Columncdx6500TCOPStatAutoCallLastOutCallCUD | read-only | mandatory | X25 Call User Data of outbound call. |
| 1.3.6.1.4.1.449.2.1.4 | Nodecdx6500Controls |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| Counter16 | INTEGER (0..65535) | ||
| DisplayString | OCTET STRING |