Wellfleet-DVMRP-MIB
129 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.18.3.5.3.12.1 | NodewfDvmrpBase | |||
| 1.3.6.1.4.1.18.3.5.3.12.1.1 | ScalarwfDvmrpBaseCreate | read-write | mandatory | This entry will provide the base configuration for the DVMRP multicast support on the router. |
| 1.3.6.1.4.1.18.3.5.3.12.1.2 | ScalarwfDvmrpBaseEnable | read-write | mandatory | Enable or disable DVMRP support in router |
| 1.3.6.1.4.1.18.3.5.3.12.1.3 | ScalarwfDvmrpBaseState | read-only | mandatory | State of DVMRP base module |
| 1.3.6.1.4.1.18.3.5.3.12.1.4 | ScalarwfDvmrpBaseFullUpdateInterval | read-write | mandatory | Full update interval. This value specifies, in seconds, how often routing messages containing complete routing tables are sent. |
| 1.3.6.1.4.1.18.3.5.3.12.1.5 | ScalarwfDvmrpBaseTriggeredUpdateInterval | read-write | mandatory | Triggered update interval. This value specifies, in seconds, how often triggered routing messages are sent; this represents the minimum amount of time between … |
| 1.3.6.1.4.1.18.3.5.3.12.1.6 | ScalarwfDvmrpBaseLeafTimeout | read-write | mandatory | Leaf timeout. This value specifies, in seconds, the virtual interface hold down timer. |
| 1.3.6.1.4.1.18.3.5.3.12.1.7 | ScalarwfDvmrpBaseNeighborTimeout | read-write | mandatory | Neighbor timeout. This value specifies, in seconds, how long a router neighbor is considered 'up' without confirmation. |
| 1.3.6.1.4.1.18.3.5.3.12.1.8 | ScalarwfDvmrpBaseRouteExpirationTimeout | read-write | mandatory | Route Expiration timeout. This value specifies, in seconds, how long a route is considered valid without confirmation; this represents the duration of time tha… |
| 1.3.6.1.4.1.18.3.5.3.12.1.9 | ScalarwfDvmrpBaseGarbageTimeout | read-write | mandatory | Garbage timeout. This value specifies, in seconds, how long a route exists without confirmation; this represents the duration of time that this route will be i… |
| 1.3.6.1.4.1.18.3.5.3.12.1.10 | ScalarwfDvmrpBaseEstimatedRoutes | read-write | mandatory | Estimated number of routes, per slot. This is used for pre-allocating routing tables. Note that routes are kept on a per-source network basis, independent of m… |
| 1.3.6.1.4.1.18.3.5.3.12.1.11 | ScalarwfDvmrpBaseNeighborProbeInterval | read-write | mandatory | Neighbor probe interval: how often to send a probe on VIFs |
| 1.3.6.1.4.1.18.3.5.3.12.1.12 | ScalarwfDvmrpBaseRouteSwitchTimeout | read-write | mandatory | Route switch timeout. How long to wait, without receiving a subsequent route update from the original neighbor, before switching to a different neighbor. |
| 1.3.6.1.4.1.18.3.5.3.12.1.13 | ScalarwfDvmrpBaseActualRoutes | read-only | mandatory | Count of number of entries currently in route table |
| 1.3.6.1.4.1.18.3.5.3.12.1.14 | ScalarwfDvmrpBaseDebugLevel | read-write | mandatory | Turn DVMRP log ON or OFF for DVMRP debuging messages The levels are: NO_DISPLAY_LOG 0x0001 - Reserved ROUTE_UPDATE_LOG 0x0002 - Displays all routing table even… |
| 1.3.6.1.4.1.18.3.5.3.12.1.15 | ScalarwfDvmrpBasePruningEnable | read-write | mandatory | Enable or Disable Pruning functionality at the Base level |
| 1.3.6.1.4.1.18.3.5.3.12.1.16 | ScalarwfDvmrpBaseFragmentMtuThreshold | read-write | obsolete | the default value is the CSMACD_MTU, and the MINiMUN is X25_DDN_MTU. Both are taken from dp.h |
| 1.3.6.1.4.1.18.3.5.3.12.1.17 | ScalarwfDvmrpBaseMaxRoutes | read-write | mandatory | Max number of routes, per slot. This is used to limit the size of routing tables. Note that routes are kept on a per-source network basis, independent of multi… |
| 1.3.6.1.4.1.18.3.5.3.12.1.18 | ScalarwfDvmrpBasePolicyEnable | read-write | obsolete | Enable or Disable route policy functionality at the Base level |
| 1.3.6.1.4.1.18.3.5.3.12.1.19 | ScalarwfDvmrpBaseHolddownEnable | read-write | mandatory | Enable or Disable holddown of deleted routes. |
| 1.3.6.1.4.1.18.3.5.3.12.2 | TablewfDvmrpCircuitEntryTable | not-accessible | mandatory | Circuit virtual interfaces (aka physical VIFs) |
| 1.3.6.1.4.1.18.3.5.3.12.2.1 | RowwfDvmrpCircuitEntry | not-accessible | mandatory | One instance of this object exists for every CCT that supports this feature. The instance ID for this object will be the circuit number. |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.1 | ColumnwfDvmrpCircuitCreate | read-write | mandatory | Create or delete |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.2 | ColumnwfDvmrpCircuitEnable | read-write | mandatory | Enable or disable DVMRP on this circuit |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.3 | ColumnwfDvmrpCircuitState | read-only | mandatory | The current state of the DVMRP interface. Invalid indicates an error in processing the configuration record. |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.4 | ColumnwfDvmrpCircuitCCT | read-only | mandatory | This circuit number. |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.5 | ColumnwfDvmrpCircuitRouteEnable | read-write | mandatory | Enable/disble this circuit for routing. If enabled, this circuit will be used to propogate routing information, information about this circuit will be incorpor… |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.6 | ColumnwfDvmrpCircuitMetric | read-write | mandatory | Metric. This value represents the cost of this interface; the cost of using this hop. This value must be smaller than the route infinity value |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.7 | ColumnwfDvmrpCircuitRouteThreshold | read-write | mandatory | Threshold. This value can be used to filter out datagrams that are being forwarded to a neighboring router; if the IP TTL is not >= the threshold, the datagram… |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.8 | ColumnwfDvmrpCircuitInPkts | read-only | mandatory | Number of datagrams received on this interface |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.9 | ColumnwfDvmrpCircuitOutPkts | read-only | mandatory | Number of datagrams send on this interface |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.10 | ColumnwfDvmrpCircuitInRouteUpdates | read-only | mandatory | Number of DVMRP route update messages received |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.11 | ColumnwfDvmrpCircuitOutRouteUpdates | read-only | mandatory | Number of DVMRP route update messages sent |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.12 | ColumnwfDvmrpCircuitInPktDiscards | read-only | mandatory | Number of inbound datagrams discarded due to route not found |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.13 | ColumnwfDvmrpCircuitOutPktDiscards | read-only | mandatory | Number of outbound datagrams discarded due to route not found |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.14 | ColumnwfDvmrpCircuitFwdCacheSize | read-write | mandatory | Maximum number of entries allowed in the Forwarding table at one time. there is a Forwarding table per vif |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.15 | ColumnwfDvmrpCircuitFwdCacheTTL | read-write | mandatory | The time_to_live for the Forwarding table entries in seconds . |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.16 | ColumnwfDvmrpCircuitAdvertiseSelf | read-write | mandatory | If enabled the router will advertise itself as one of the source net. If not enabled the router will not advertise itself as one of the source net. |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.17 | ColumnwfDvmrpCircuitFwdCacheEntries | read-only | mandatory | The most up to date number of entries in the forwarding cache |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.18 | ColumnwfDvmrpCircuitInPrunePkts | read-only | mandatory | Number of PRUNE datagrams received on this interface |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.19 | ColumnwfDvmrpCircuitOutPrunePkts | read-only | mandatory | Number of PRUNE datagrams send on this interface |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.20 | ColumnwfDvmrpCircuitInGraftPkts | read-only | mandatory | Number of GRAFT datagrams received on this interface |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.21 | ColumnwfDvmrpCircuitOutGraftPkts | read-only | mandatory | Number of GRAFT datagrams send on this interface |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.22 | ColumnwfDvmrpCircuitInGraftAckPkts | read-only | mandatory | Number of GRAFT_ACK datagrams received on this interface |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.23 | ColumnwfDvmrpCircuitOutGraftAckPkts | read-only | mandatory | Number of GRAFT_ACK datagrams send on this interface |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.24 | ColumnwfDvmrpCircuitDefaultRouteSupply | read-write | mandatory | enabled : Send the default route, 0.0.0.0 if learned, form this interface. disabled: no default route is sent from this interface. generate: generate default r… |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.25 | ColumnwfDvmrpCircuitDefaultRouteListen | read-write | mandatory | Receive the default route, 0.0.0.0 on this interface |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.26 | ColumnwfDvmrpCircuitReportDependProbe | read-write | mandatory | This is to control accepting the route report. According to the protocol, dvmrp should send probe packet before sending the route report packet to the neighbor… |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.27 | ColumnwfDvmrpCircuitPruneLifeTime | read-write | mandatory | The life time of the prune message the router sends to its neighbor in seconds. |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.28 | ColumnwfDvmrpCircuitAcceptAggregateRoutes | read-only | mandatory | Count of number of routes received have been aggregated to the specific aggregate route currently in route table for this interface. |
| 1.3.6.1.4.1.18.3.5.3.12.2.1.29 | ColumnwfDvmrpCircuitAnnounceAggregatedRoutes | read-only | mandatory | Count of number of routes have been aggregated to the specific aggregate route for advertisement currently in route table for this interface. |
| 1.3.6.1.4.1.18.3.5.3.12.3 | TablewfDvmrpTunnelEntryTable | not-accessible | mandatory | Tunnel virtual interfaces |
| 1.3.6.1.4.1.18.3.5.3.12.3.1 | RowwfDvmrpTunnelEntry | not-accessible | mandatory | This object is used to specify the set of 'multicast tunnels', unicast pipes that are used to send IP multicast datagrams to remote network multicast routers v… |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.1 | ColumnwfDvmrpTunnelCreate | read-write | mandatory | create/delete |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.2 | ColumnwfDvmrpTunnelEnable | read-write | mandatory | enable/disable this tunnel interface |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.3 | ColumnwfDvmrpTunnelState | read-only | mandatory | The current state of the DVMRP tunnel interface. Invalid indicates an error in processing the configuration record. |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.4 | ColumnwfDvmrpTunnelCCT | read-only | mandatory | The multicast circuit associated with this tunnel. |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.5 | ColumnwfDvmrpTunnelRemoteRouterIpAddress | read-only | mandatory | (unicast) IP address of remote network router neighbor. |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.6 | ColumnwfDvmrpTunnelEncapsMode | read-write | mandatory | Will these tunnelled datagrams be encapsulated within an IP datagram, or will they be loosely encapsulated using the LSSR option (for the latter, refer to RFC … |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.7 | ColumnwfDvmrpTunnelMetric | read-write | mandatory | Cost of using this tunnel |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.8 | ColumnwfDvmrpTunnelThreshold | read-write | mandatory | Threshold for forwarding through this tunnel; if TTL < threshold, the datagram is dropped. |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.9 | ColumnwfDvmrpTunnelInPkts | read-only | mandatory | Number of datagrams received on this interface |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.10 | ColumnwfDvmrpTunnelOutPkts | read-only | mandatory | Number of datagrams send on this interface |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.11 | ColumnwfDvmrpTunnelInRouteUpdates | read-only | mandatory | Number of DVMRP route update messages received |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.12 | ColumnwfDvmrpTunnelOutRouteUpdates | read-only | mandatory | Number of DVMRP route update messages sent |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.13 | ColumnwfDvmrpTunnelInPktDiscards | read-only | mandatory | Number of inbound datagrams discarded due to route not found or due to invalid inner address (dest address != multicast) |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.14 | ColumnwfDvmrpTunnelOutPktDiscards | read-only | mandatory | Number of outbound datagrams discarded due to route not found |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.15 | ColumnwfDvmrpTunnelLocalRouterIpAddress | read-only | mandatory | (unicast) IP address of local network router. To support multinet. |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.16 | ColumnwfDvmrpTunnelFwdCacheSize | read-write | mandatory | Maximum number of entries allowed in the Forwarding table at one time. there is a Forwarding table per vif |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.17 | ColumnwfDvmrpTunnelFwdCacheTTL | read-write | mandatory | The time_to_live for the Forwarding table entries in seconds . |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.18 | ColumnwfDvmrpTunnelFwdCacheEntries | read-only | mandatory | The most up to date number of entries in the forwarding cache |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.19 | ColumnwfDvmrpTunnelInPrunePkts | read-only | mandatory | Number of PRUNE datagrams received on this interface |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.20 | ColumnwfDvmrpTunnelOutPrunePkts | read-only | mandatory | Number of PRUNE datagrams send on this interface |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.21 | ColumnwfDvmrpTunnelInGraftPkts | read-only | mandatory | Number of GRAFT datagrams received on this interface |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.22 | ColumnwfDvmrpTunnelOutGraftPkts | read-only | mandatory | Number of GRAFT datagrams send on this interface |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.23 | ColumnwfDvmrpTunnelInGraftAckPkts | read-only | mandatory | Number of GRAFT_ACK datagrams received on this interface |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.24 | ColumnwfDvmrpTunnelOutGraftAckPkts | read-only | mandatory | Number of GRAFT_ACK datagrams send on this interface |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.25 | ColumnwfDvmrpTunnelDefaultRouteSupply | read-write | mandatory | Send the default route, 0.0.0.0 on this interface |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.26 | ColumnwfDvmrpTunnelDefaultRouteListen | read-write | mandatory | Receive the default route, 0.0.0.0 on this interface |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.27 | ColumnwfDvmrpTunnelCtrlMsgMode | read-write | mandatory | Dvmrp tunneling control messages encapsulated type. noencaps is the mode that control messages are sent in regular igmp packets with ip protocol type set to IP… |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.28 | ColumnwfDvmrpTunnelReportDependProbe | read-write | mandatory | This is to control accepting the route report. According to the protocol, dvmrp should send probe packet before sending the route report packet to the neighbor… |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.29 | ColumnwfDvmrpTunnelPruneLifeTime | read-write | mandatory | The life time of the prune message the router send to its neighbor in seconds. |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.30 | ColumnwfDvmrpTunnelAcceptAggregateRoutes | read-only | mandatory | Count of number of routes received have been aggregated to the specific aggregate route currently in route table for this interface. |
| 1.3.6.1.4.1.18.3.5.3.12.3.1.31 | ColumnwfDvmrpTunnelAnnounceAggregatedRoutes | read-only | mandatory | Count of number of routes have been aggregated to the specific aggregate route for advertisement currently in route table for this interface. |
| 1.3.6.1.4.1.18.3.5.3.12.4 | TablewfDvmrpRouteEntryTable | not-accessible | mandatory | MIB proxy: main DVMRP routing table |
| 1.3.6.1.4.1.18.3.5.3.12.4.1 | RowwfDvmrpRouteEntry | not-accessible | mandatory | Supported by mib proxy. One entry exists for each active route. |
| 1.3.6.1.4.1.18.3.5.3.12.4.1.1 | ColumnwfDvmrpRouteSourceNetwork | read-only | mandatory | A source of multicast datagrams |
| 1.3.6.1.4.1.18.3.5.3.12.4.1.2 | ColumnwfDvmrpRouteSourceMask | read-only | mandatory | Mask for the specified source network |
| 1.3.6.1.4.1.18.3.5.3.12.4.1.3 | ColumnwfDvmrpRouteNextHopRouter | read-only | mandatory | Next hop multicast router to the specified source network; we consider this neighboring router to be on the shortest path to the source. Note that this neighbo… |
| 1.3.6.1.4.1.18.3.5.3.12.4.1.4 | ColumnwfDvmrpRouteNextHopInterfaceCCT | read-only | mandatory | Next hop interface (CCT) to the specified source router; we consider this interface to be on the shortest path to the source. |
| 1.3.6.1.4.1.18.3.5.3.12.4.1.5 | ColumnwfDvmrpRouteNextHopInterfaceTunnelId | read-only | mandatory | Next hop interface (tunnel id) to the specified source router; we consider this interface to be on the shortest path to the source. |
| 1.3.6.1.4.1.18.3.5.3.12.4.1.6 | ColumnwfDvmrpRouteNextHopInterfaceLocalTunnelId | read-only | mandatory | Next hop interface (local tunnel id) to the specified source router; we consider this interface to be on the shortest path to the source. |
| 1.3.6.1.4.1.18.3.5.3.12.4.1.7 | ColumnwfDvmrpRouteTimer | read-only | mandatory | route timer |
| 1.3.6.1.4.1.18.3.5.3.12.4.1.8 | ColumnwfDvmrpRouteState | read-only | mandatory | Set of flags indicating state of entry. Note that the router uses this field as a bit mask. 0x8000 Network is local to this router 0x4000 Route is being timed … |
| 1.3.6.1.4.1.18.3.5.3.12.4.1.9 | ColumnwfDvmrpRouteMetric | read-only | mandatory | current route metric |
| 1.3.6.1.4.1.18.3.5.3.12.4.1.10 | ColumnwfDvmrpRouteProtocol | read-only | mandatory | current route protocol dvmrp (2) or mospf (4) or internal (6) which is the route from unicast and incoming interface no i dvmrp configure, if dvmrp is configur… |
| 1.3.6.1.4.1.18.3.5.3.12.4.1.11 | ColumnwfDvmrpRouteType | read-only | mandatory | The orginal route source from. If it is from pure dvmrp route (0x0001) unicast best route (0x0002) unciast route but has dvmrp interface (0x0003) ospf(0x0004) … |
| 1.3.6.1.4.1.18.3.5.3.12.4.1.12 | ColumnwfDvmrpRouteAggregatedType | read-only | mandatory | Route Aggregated types : 0 - normal route 1 - inbound aggregated route 2 - outbound aggregated route 4 - inbound aggregate route 8 - outbound aggregate route |
| 1.3.6.1.4.1.18.3.5.3.12.5 | TablewfDvmrpRouteInterfaceEntryTable | not-accessible | mandatory | MIB proxy: DVMRP VIF routing table |
| 1.3.6.1.4.1.18.3.5.3.12.5.1 | RowwfDvmrpRouteInterfaceEntry | not-accessible | mandatory | Supported by mib proxy. One entry exists for each virtual interface on an active route. It is associated with a route via the source network/ net mask fields. … |
| 1.3.6.1.4.1.18.3.5.3.12.5.1.1 | ColumnwfDvmrpRouteInterfaceSourceNetwork | read-only | mandatory | A source of multicast datagrams |
| 1.3.6.1.4.1.18.3.5.3.12.5.1.2 | ColumnwfDvmrpRouteInterfaceSourceMask | read-only | mandatory | Mask for the specified source network |
| 1.3.6.1.4.1.18.3.5.3.12.5.1.3 | ColumnwfDvmrpRouteInterfaceNextHopInterfaceCCT | read-only | mandatory | circuit number with which this route is associated |
| 1.3.6.1.4.1.18.3.5.3.12.5.1.4 | ColumnwfDvmrpRouteInterfaceNextHopInterfaceLocalTunnelId | read-only | mandatory | Tunnel ID for tunnelled interfaces. This value is zero for non-tunnelled interfaces, otherwise it contains the local IP address of the tunnel. |
| 1.3.6.1.4.1.18.3.5.3.12.5.1.5 | ColumnwfDvmrpRouteInterfaceNextHopInterfaceTunnelId | read-only | mandatory | Tunnel ID for tunnelled interfaces. This value is zero for non-tunnelled interfaces, otherwise it contains the remote IP address of the tunnel. |
| 1.3.6.1.4.1.18.3.5.3.12.5.1.6 | ColumnwfDvmrpRouteInterfaceState | read-only | mandatory | state of interface for this route. Note that the router uses this field as a bit mask. 0x8000 - interface is leaf 0x4000 - interface is child 0x2000 - interfac… |
| 1.3.6.1.4.1.18.3.5.3.12.5.1.7 | ColumnwfDvmrpRouteInterfaceDominantRouter | read-only | mandatory | dominant router address for virtual interface |
| 1.3.6.1.4.1.18.3.5.3.12.5.1.8 | ColumnwfDvmrpRouteInterfaceSubordinateRouter | read-only | mandatory | subordinate router address for virtual interface |
| 1.3.6.1.4.1.18.3.5.3.12.5.1.9 | ColumnwfDvmrpRouteInterfaceHoldDownTimer | read-only | mandatory | Current value of hold down timer, used to determine if interface is for leaf or non-leaf network. Non-leaf network means that a local network router considers … |
| 1.3.6.1.4.1.18.3.5.3.12.5.1.10 | ColumnwfDvmrpRouteInterfaceSPInDiscards | read-only | obsolete | Count of inbound packets discarded because interface not on shortest path |
| 1.3.6.1.4.1.18.3.5.3.12.5.1.11 | ColumnwfDvmrpRouteInterfaceSPOutDiscards | read-only | obsolete | Count of outbound packets discarded because interface not on shortest path |
| 1.3.6.1.4.1.18.3.5.3.12.5.1.12 | ColumnwfDvmrpRouteInterfaceThresholdOutDiscards | read-only | obsolete | Count of outbound packets discarded because of threshold |
| 1.3.6.1.4.1.18.3.5.3.12.5.1.13 | ColumnwfDvmrpRouteInterfaceInSuccessfulPkts | read-only | obsolete | Count of inbound packets accepted for forwarding |
| 1.3.6.1.4.1.18.3.5.3.12.5.1.14 | ColumnwfDvmrpRouteInterfaceOutSuccessfulPkts | read-only | obsolete | Count of outbound packets accepted for forwarding |
| 1.3.6.1.4.1.18.3.5.3.12.5.1.15 | ColumnwfDvmrpRouteInterfaceParentCCT | read-only | mandatory | circuit number with which this route is associated;parent VIF |
| 1.3.6.1.4.1.18.3.5.3.12.5.1.16 | ColumnwfDvmrpRouteInterfaceParentLocalTunnelId | read-only | mandatory | Tunnel ID for tunnelled interfaces. This value is zero for non-tunnelled interfaces, otherwise it contains the local IP address of the tunnel; parent VIF. |
| 1.3.6.1.4.1.18.3.5.3.12.5.1.17 | ColumnwfDvmrpRouteInterfaceParentTunnelId | read-only | mandatory | Tunnel ID for tunnelled interfaces. This value is zero for non-tunnelled interfaces, otherwise it contains the remote IP address of the tunnel; parent VIF. |
| 1.3.6.1.4.1.18.3.5.3.12.6 | TablewfDvmrpNeighboringRouterEntryTable | not-accessible | mandatory | MIB proxy: DVMRP neighbor table |
| 1.3.6.1.4.1.18.3.5.3.12.6.1 | RowwfDvmrpNeighboringRouterEntry | not-accessible | mandatory | This entry is used to indentify the known neighboring routers for a circuit. This object will be indentified by circuit number, tunnel id (to identify local in… |
| 1.3.6.1.4.1.18.3.5.3.12.6.1.1 | ColumnwfDvmrpNeighboringRouterCCT | read-only | mandatory | Local circuit number |
| 1.3.6.1.4.1.18.3.5.3.12.6.1.2 | ColumnwfDvmrpNeighboringRouterLocalTunnelId | read-only | mandatory | Tunnel Id for interface. This value is zero for non- tunnelled interfaces, otherwise it contains the IP address of the local tunnel endpoint. |
| 1.3.6.1.4.1.18.3.5.3.12.6.1.3 | ColumnwfDvmrpNeighboringRouterTunnelId | read-only | mandatory | Tunnel Id for interface. This value is zero for non- tunnelled interfaces, otherwise it contains the IP address of the remote tunnel endpoint. |
| 1.3.6.1.4.1.18.3.5.3.12.6.1.4 | ColumnwfDvmrpNeighboringRouterIpAddr | read-only | mandatory | IP address of neighboring router |
| 1.3.6.1.4.1.18.3.5.3.12.6.1.5 | ColumnwfDvmrpNeighboringRouterState | read-only | mandatory | State of neighbor. The router uses this as a bit mask. 0x8000 - Neighbor is being timed |
| 1.3.6.1.4.1.18.3.5.3.12.6.1.6 | ColumnwfDvmrpNeighboringRouterTimer | read-only | mandatory | Current value of neighbor timer |
| 1.3.6.1.4.1.18.3.5.3.12.6.1.7 | ColumnwfDvmrpNeighboringRouterGenId | read-only | mandatory | The neighboring router's generation identifier. |
| 1.3.6.1.4.1.18.3.5.3.12.6.1.8 | ColumnwfDvmrpNeighboringRouterMajorVersion | read-only | mandatory | The neighboring router's major DVMRP version number. |
| 1.3.6.1.4.1.18.3.5.3.12.6.1.9 | ColumnwfDvmrpNeighboringRouterMinorVersion | read-only | mandatory | The neighboring router's minor DVMRP version number. |
| 1.3.6.1.4.1.18.3.5.3.12.6.1.10 | ColumnwfDvmrpNeighboringRouterCapabilities | read-only | mandatory | This object describes the neighboring router's capabilities. The leaf bit indicates that the neighbor has only one interface with neighbors. The prune bit indi… |