Wellfleet-NAT-MIB
145 objects
No module-level DESCRIPTION found.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.18.3.5.3.2.7.1 | NodewfNatBase | |||
| 1.3.6.1.4.1.18.3.5.3.2.7.1.1 | ScalarwfNatBaseDelete | read-write | mandatory | 'This value determines whether NAT is configured' |
| 1.3.6.1.4.1.18.3.5.3.2.7.1.2 | ScalarwfNatBaseDisable | read-write | mandatory | 'The administrative status of NAT in the router. The value 'enabled' denotes that the NAT Process is active on at least one interface; 'disabled' disables it o… |
| 1.3.6.1.4.1.18.3.5.3.2.7.1.3 | ScalarwfNatBaseState | read-only | mandatory | 'The state of NAT' |
| 1.3.6.1.4.1.18.3.5.3.2.7.1.4 | ScalarwfNatBaseSoloistSlotMask | read-write | mandatory | Slot mask for which slots the soloist gate is eligible to run on. The MSBit represents slot 1, the next most significant bit represents slot 2, and so on... Sl… |
| 1.3.6.1.4.1.18.3.5.3.2.7.1.5 | ScalarwfNatBaseSoloistSlot | read-only | mandatory | Slot on which NAT soloist gate is running. Slots can be 1-14. Default is zero. |
| 1.3.6.1.4.1.18.3.5.3.2.7.1.6 | ScalarwfNatBaseLogMask | read-write | mandatory | A parameter to specify which NAT log messages should be logged. Each bit represents a message as defined below. A 1 in that bit location means to log it and a … |
| 1.3.6.1.4.1.18.3.5.3.2.7.1.7 | ScalarwfNatBaseMapTimeout | read-write | mandatory | This controls whether or not the dynamic mapping table entries are aged out when unused. |
| 1.3.6.1.4.1.18.3.5.3.2.7.1.8 | ScalarwfNatBaseMapMaxTimeout | read-write | mandatory | The maximum time in seconds before unused NAT mapping table entries are deleted. This timeout or aging does not apply to static mapping entries. |
| 1.3.6.1.4.1.18.3.5.3.2.7.1.9 | ScalarwfNatBaseMapDynMapsCount | read-only | mandatory | Number of Dynamic Mappings in the dymanic mapping table |
| 1.3.6.1.4.1.18.3.5.3.2.7.1.10 | ScalarwfNatBaseFtpSessionCount | read-only | mandatory | Number of FTP sessions detected on this box translated by NAT |
| 1.3.6.1.4.1.18.3.5.3.2.7.1.11 | ScalarwfNatBaseNto1TrTotCount | read-only | mandatory | Total number of active Nto1 translation counts on the box. |
| 1.3.6.1.4.1.18.3.5.3.2.7.1.12 | ScalarwfNatBaseSynchronization | read-write | mandatory | The administrative status of NAT Synchronization in the router. The value `enabled' denotes that the NAT Synchronization is active and is synchronizing with th… |
| 1.3.6.1.4.1.18.3.5.3.2.7.1.13 | ScalarwfNatBaseSynRouterID | read-write | mandatory | This represents the Router Identifier for NAT Synchronization Only. This is used to detect the duplicate TCP connection between peers. The value of it can be a… |
| 1.3.6.1.4.1.18.3.5.3.2.7.1.14 | ScalarwfNatBaseSynPort | read-write | mandatory | This represents the TCP port on which the connection requests from the peers will be accepted. When NAT Synchronization Protocol comes up, it will open a liste… |
| 1.3.6.1.4.1.18.3.5.3.2.7.1.15 | ScalarwfNatBaseSynKeepAlvInterval | read-write | mandatory | Idle session timeout period, in seconds. If an established TCP connection remains inactive for this interval, KEEPALIVE messages will be sent to the peer (if t… |
| 1.3.6.1.4.1.18.3.5.3.2.7.1.16 | ScalarwfNatBaseSynKeepAlvTimer | read-write | mandatory | KEEPALIVE retransmit timeout period, in seconds. This is the interval at which unacknowledged KEEPALIVE messages will be retransmitted. If the Idle Timer is se… |
| 1.3.6.1.4.1.18.3.5.3.2.7.1.17 | ScalarwfNatBaseSynKeepAlvRetries | read-write | mandatory | Number of unacknowledged KEEPALIVE messages retransmitted before the TCP session is terminated. If this count is set to zero, only one KEEPALIVE message will b… |
| 1.3.6.1.4.1.18.3.5.3.2.7.1.18 | ScalarwfNatBaseLocalToLocalEnable | read-write | mandatory | Allow forwarding of traffic from one local NAT interface to another local NAT interface. |
| 1.3.6.1.4.1.18.3.5.3.2.7.1.19 | ScalarwfNatBaseInstallUniPrivAddr | read-write | mandatory | This MIB was added in BayRS 14.20 to address a compatibility issue concerning non-DNS NAT translations when upgrading from a pre-14.20 NAT configuration to a 1… |
| 1.3.6.1.4.1.18.3.5.3.2.7.2 | TablewfNatAddrRangeTable | not-accessible | mandatory | Table of address ranges that have been designated as the set of external apparent addresses that are to be mapped in place of internal actual addresses. These … |
| 1.3.6.1.4.1.18.3.5.3.2.7.2.1 | RowwfNatAddrRangeEntry | not-accessible | mandatory | 'Information describing each of the available address ranges.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.2.1.1 | ColumnwfNatAddrRangeDelete | read-write | mandatory | 'Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete an address range entry.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.2.1.2 | ColumnwfNatAddrRangeDisable | read-write | mandatory | 'Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable an address range entry.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.2.1.3 | ColumnwfNatAddrRangeAddress | read-write | mandatory | 'The IP beginning address of this range entry. |
| 1.3.6.1.4.1.18.3.5.3.2.7.2.1.4 | ColumnwfNatAddrRangePrefixLen | read-write | mandatory | 'The IP address mask that in conjunction with the start address defines the address range of the entry.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.3 | TablewfNatLocalAddrRangeTable | not-accessible | mandatory | Table of address ranges that have been designated as the set of local addresses that are to be mapped via NAT. |
| 1.3.6.1.4.1.18.3.5.3.2.7.3.1 | RowwfNatLocalAddrRangeEntry | not-accessible | mandatory | 'Information describing each of the available address ranges.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.3.1.1 | ColumnwfNatLocalAddrRangeDelete | read-write | mandatory | 'Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete an address range entry.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.3.1.2 | ColumnwfNatLocalAddrRangeDisable | read-write | mandatory | 'Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable an address range entry.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.3.1.3 | ColumnwfNatLocalAddrRangeAddress | read-write | mandatory | 'The IP beginning address of this range entry. |
| 1.3.6.1.4.1.18.3.5.3.2.7.3.1.4 | ColumnwfNatLocalAddrRangePrefixLen | read-write | mandatory | 'The IP address mask that in conjunction with the start address defines the address range of the entry.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.3.1.5 | ColumnwfNatLocalAddrRangeNto1Addr | read-write | mandatory | Nto1 translation address used for this range. |
| 1.3.6.1.4.1.18.3.5.3.2.7.4 | TablewfNatStaticMapTable | not-accessible | mandatory | 'This table creates instances of pre-defined NAT mappings.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.4.1 | RowwfNatStaticMapEntry | not-accessible | mandatory | 'A single local-to-global address mapping.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.4.1.1 | ColumnwfNatStaticMapDelete | read-write | mandatory | 'Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete a static address mapping entry.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.4.1.2 | ColumnwfNatStaticMapDisable | read-write | mandatory | 'Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable a static address mapping entry.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.4.1.3 | ColumnwfNatStaticMapLocalAddress | read-write | mandatory | 'The local or private address of the mapping pair.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.4.1.4 | ColumnwfNatStaticMapGlobalAddress | read-write | mandatory | 'The global or external address of the mapping pair.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.4.1.5 | ColumnwfNatStaticMapProtocol | read-write | mandatory | 'The IP protocol of the mapping pair.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.4.1.6 | ColumnwfNatStaticMapLocalPort | read-write | mandatory | 'The local UDP or TCP port of the mapping pair. This will only be relevent if the protocol is either UDP or TCP.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.4.1.7 | ColumnwfNatStaticMapGlobalPort | read-write | mandatory | 'The global UDP or TCP port of the mapping pair. This will only be relevent if the protocol is either UDP or TCP.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.5 | TablewfNatMapTable | not-accessible | mandatory | 'This table defines the current set of address mappings that are in effect.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.5.1 | RowwfNatMapEntry | not-accessible | mandatory | |
| 1.3.6.1.4.1.18.3.5.3.2.7.5.1.1 | ColumnwfNatMapLocalAddress | read-only | mandatory | 'The local address of the mapping pair.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.5.1.2 | ColumnwfNatMapGlobalAddress | read-only | mandatory | 'The global address of the mapping pair.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.5.1.3 | ColumnwfNatMapProtocol | read-only | mandatory | 'The IP protocol of the mapping pair.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.5.1.4 | ColumnwfNatMapLocalPort | read-only | mandatory | 'When the mapping is for a TCP connection, this denotes the TCP port number on the local side.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.5.1.5 | ColumnwfNatMapGlobalPort | read-only | mandatory | 'When the mapping is for a TCP connection, this denotes the TCP port number on the global side.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.5.1.6 | ColumnwfNatMapTxCount | read-only | mandatory | 'Number of packets for this mapping pair that have been mapped from the local to the global network.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.5.1.7 | ColumnwfNatMapRxCount | read-only | mandatory | 'Number of packets for this mapping pair that have been mapped from the global to the local network.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.5.1.8 | ColumnwfNatMapTimeout | read-only | mandatory | 'The time in seconds since this mapping entry was last used. This is used to age out mapping entries.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.5.1.9 | ColumnwfNatMapMode | read-only | mandatory | This is the bit mask representing the type of this mapping. Each bit specifies the type as follows: The mapping could be only ONE of the foolowing three... 0x0… |
| 1.3.6.1.4.1.18.3.5.3.2.7.6 | TablewfNatIfTable | not-accessible | mandatory | 'The set of interface that are participating in the NAT protocol.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.6.1 | RowwfNatIfEntry | not-accessible | mandatory | 'An single instance of a NAT interface entry.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.6.1.1 | ColumnwfNatIfDelete | read-write | mandatory | This variable determines in a NAT Interface has been configured on the router. |
| 1.3.6.1.4.1.18.3.5.3.2.7.6.1.2 | ColumnwfNatIfDisable | read-write | mandatory | 'The NAT interface's administrative status. The value 'enabled' denotes that NAT has been configured on the interface. The value 'disabled' denotes that the in… |
| 1.3.6.1.4.1.18.3.5.3.2.7.6.1.3 | ColumnwfNatIfIpAddress | read-only | mandatory | The IP address of this NAT interface. |
| 1.3.6.1.4.1.18.3.5.3.2.7.6.1.4 | ColumnwfNatIfCircuit | read-write | mandatory | The circuit number of this interface. |
| 1.3.6.1.4.1.18.3.5.3.2.7.6.1.5 | ColumnwfNatIfType | read-write | mandatory | Denotes the type of NAT interface being defined. |
| 1.3.6.1.4.1.18.3.5.3.2.7.6.1.6 | ColumnwfNatIfState | read-only | mandatory | 'The state of NAT on this interface' |
| 1.3.6.1.4.1.18.3.5.3.2.7.6.1.7 | ColumnwfNatIfTxCount | read-only | mandatory | Number of packets mapped over this interface from the local to the global network.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.6.1.8 | ColumnwfNatIfRxCount | read-only | mandatory | Number of packets mapped over this interface from the global to the local network.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.6.1.9 | ColumnwfNatIfPktDropCount | read-only | mandatory | Number of packets dropped on this interface |
| 1.3.6.1.4.1.18.3.5.3.2.7.6.1.10 | ColumnwfNatIfDomain | read-write | mandatory | When wfNatIfType is set to biDirectional, specifies the Address Domain Name that this interface is connected to, otherwise set to null. |
| 1.3.6.1.4.1.18.3.5.3.2.7.7 | TablewfNatSynPeerTable | not-accessible | mandatory | The Nat Synchronization Peer table contains configuration and statistical information regarding this router's NAT peers |
| 1.3.6.1.4.1.18.3.5.3.2.7.7.1 | RowwfNatSynPeerEntry | not-accessible | mandatory | An entry in the NAT Synchronization-Peer table |
| 1.3.6.1.4.1.18.3.5.3.2.7.7.1.1 | ColumnwfNatSynPeerDelete | read-write | mandatory | Create/Delete: if set to delete, this instance of the peer entry is deleted, which results into the termination of peer connection. |
| 1.3.6.1.4.1.18.3.5.3.2.7.7.1.2 | ColumnwfNatSynPeerDisable | read-write | mandatory | Enable/Disable: controls whether the peer connection is enabled or disabled, disabling this results into the termination of TCP connection |
| 1.3.6.1.4.1.18.3.5.3.2.7.7.1.3 | ColumnwfNatSynPeerState | read-only | mandatory | the administrative state of the peer connection |
| 1.3.6.1.4.1.18.3.5.3.2.7.7.1.4 | ColumnwfNatSynPeerConnType | read-only | mandatory | the type of the TCP connection with the peer, whether this connection is accepted from the peer or it was actively initialted by this router to the peer. |
| 1.3.6.1.4.1.18.3.5.3.2.7.7.1.5 | ColumnwfNatSynPeerRouterID | read-only | mandatory | A unique non-zero RouterID of the peer that this router is expecting from the connection This is also the instance of the Peer Entry. |
| 1.3.6.1.4.1.18.3.5.3.2.7.7.1.6 | ColumnwfNatSynPeerAddress | read-write | mandatory | the IP Address of the peer, where the router will send a connect request |
| 1.3.6.1.4.1.18.3.5.3.2.7.7.1.7 | ColumnwfNatSynPeerTransSent | read-only | mandatory | The number of translations sent to this peer by the router |
| 1.3.6.1.4.1.18.3.5.3.2.7.7.1.8 | ColumnwfNatSynPeerTransRecd | read-only | mandatory | The number of translations received from this peer by the router |
| 1.3.6.1.4.1.18.3.5.3.2.7.8 | TablewfNatAddressRangeTable | not-accessible | mandatory | Table of address ranges. This table was replaced by wfNatSrcAddressFilterTable and wfNatTranslationPoolTable |
| 1.3.6.1.4.1.18.3.5.3.2.7.8.1 | RowwfNatAddressRangeEntry | not-accessible | mandatory | Information describing each of the available address ranges. |
| 1.3.6.1.4.1.18.3.5.3.2.7.8.1.1 | ColumnwfNatAddressRangeDelete | read-write | mandatory | Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete an address range entry. |
| 1.3.6.1.4.1.18.3.5.3.2.7.8.1.2 | ColumnwfNatAddressRangeDisable | read-write | mandatory | Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable an address range entry. |
| 1.3.6.1.4.1.18.3.5.3.2.7.8.1.3 | ColumnwfNatAddressRangeAddress | read-only | mandatory | The IP beginning address of this range entry. |
| 1.3.6.1.4.1.18.3.5.3.2.7.8.1.4 | ColumnwfNatAddressRangePrefixLen | read-only | mandatory | The number of contiguous bits set in the IP address mask which are used to define the address range of the entry. |
| 1.3.6.1.4.1.18.3.5.3.2.7.8.1.5 | ColumnwfNatAddressRangeIndex | read-only | mandatory | A unique value for this entry in wfNatAddressRangeTable. |
| 1.3.6.1.4.1.18.3.5.3.2.7.8.1.6 | ColumnwfNatAddressRangeNto1Addr | read-write | mandatory | When wfNatAddressRangeType is set to srcAddrFilter, specifies the N-to-1 translation address used for this range, otherwise set to zero. |
| 1.3.6.1.4.1.18.3.5.3.2.7.8.1.7 | ColumnwfNatAddressRangeType | read-write | mandatory | Denotes the type of address range being defined. sourceAddrFilter: a range of IP addresses used to detect packets which need traditional NAT forwarding. transl… |
| 1.3.6.1.4.1.18.3.5.3.2.7.8.1.8 | ColumnwfNatAddressRangeDomain | read-write | mandatory | When wfNatAddressRangeType is set to domainSrcAddrFilter or domainTransPool, specifies the Address Domain Name that this address range is valid for, otherwise … |
| 1.3.6.1.4.1.18.3.5.3.2.7.8.1.9 | ColumnwfNatAddressRangeTransPool | read-write | mandatory | This attribute is only valid for the wfNatAddressRangeType as domainSrcAddrFilter(3). The value of this attribute decides where to get the translation address … |
| 1.3.6.1.4.1.18.3.5.3.2.7.8.1.10 | ColumnwfNatAddressRangeStaticNextHop | read-write | mandatory | The IP address of the next hop of this range entry. |
| 1.3.6.1.4.1.18.3.5.3.2.7.8.1.11 | ColumnwfNatAddressRangeUnnumCct | read-write | mandatory | This Nat Address range over the unnumbered interface. |
| 1.3.6.1.4.1.18.3.5.3.2.7.9 | TablewfNatStaticMappingTable | not-accessible | mandatory | `This table creates instances of pre-defined NAT translations.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.9.1 | RowwfNatStaticMappingEntry | not-accessible | mandatory | A single original source address to translated address translation. |
| 1.3.6.1.4.1.18.3.5.3.2.7.9.1.1 | ColumnwfNatStaticMappingDelete | read-write | mandatory | Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete a static address translation entry. |
| 1.3.6.1.4.1.18.3.5.3.2.7.9.1.2 | ColumnwfNatStaticMappingDisable | read-write | mandatory | Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable a static address translation entry. |
| 1.3.6.1.4.1.18.3.5.3.2.7.9.1.3 | ColumnwfNatStaticMappingOrigAddress | read-write | mandatory | The original (un-translated) address of the translation. |
| 1.3.6.1.4.1.18.3.5.3.2.7.9.1.4 | ColumnwfNatStaticMappingTransAddress | read-only | mandatory | The translated address of the translation. |
| 1.3.6.1.4.1.18.3.5.3.2.7.9.1.5 | ColumnwfNatStaticMappingProtocol | read-only | mandatory | The IP protocol of the translation. Example values are 6 for TCP, and 17 for UDP. |
| 1.3.6.1.4.1.18.3.5.3.2.7.9.1.6 | ColumnwfNatStaticMappingOrigPort | read-write | mandatory | The original (domain specific) UDP or TCP port of the translation. This will only be relevent if the protocol is either UDP or TCP. |
| 1.3.6.1.4.1.18.3.5.3.2.7.9.1.7 | ColumnwfNatStaticMappingTransPort | read-only | mandatory | The translated UDP or TCP port of the translation. This will only be relevent if the protocol is either UDP or TCP. |
| 1.3.6.1.4.1.18.3.5.3.2.7.9.1.8 | ColumnwfNatStaticMappingInDomain | read-write | mandatory | This attribute specifies the name of the address domain that this source translation shall be valid for. In other words, this translation shall only be valid f… |
| 1.3.6.1.4.1.18.3.5.3.2.7.9.1.9 | ColumnwfNatStaticMappingOutDomain | read-write | mandatory | This attribute specifies the name of the outbound address domain that this translation will be valid for. In other words, this translation only applies to tran… |
| 1.3.6.1.4.1.18.3.5.3.2.7.9.1.10 | ColumnwfNatStaticMappingStaticNextHop | read-write | mandatory | The IP address of the next hop of this static entry. |
| 1.3.6.1.4.1.18.3.5.3.2.7.9.1.11 | ColumnwfNatStaticMappingUnnumCct | read-write | mandatory | This Nat static translation over the unnumbered interface. |
| 1.3.6.1.4.1.18.3.5.3.2.7.10 | TablewfNatMappingTable | not-accessible | mandatory | This table defines the current set of address translations that are in effect. |
| 1.3.6.1.4.1.18.3.5.3.2.7.10.1 | RowwfNatMappingEntry | not-accessible | mandatory | A single original source address to translated address translation. |
| 1.3.6.1.4.1.18.3.5.3.2.7.10.1.1 | ColumnwfNatMappingOrigAddress | read-only | mandatory | The original (un-translated) address of the translation. |
| 1.3.6.1.4.1.18.3.5.3.2.7.10.1.2 | ColumnwfNatMappingTransAddress | read-only | mandatory | The translated address of the translation. |
| 1.3.6.1.4.1.18.3.5.3.2.7.10.1.3 | ColumnwfNatMappingProtocol | read-only | mandatory | `The IP protocol of the translation.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.10.1.4 | ColumnwfNatMappingOrigPort | read-only | mandatory | When the translation is for a TCP connection, this denotes the original TCP port number. |
| 1.3.6.1.4.1.18.3.5.3.2.7.10.1.5 | ColumnwfNatMappingTransPort | read-only | mandatory | When the translation is for a TCP connection, this denotes the translated TCP port number. |
| 1.3.6.1.4.1.18.3.5.3.2.7.10.1.6 | ColumnwfNatMappingTxCount | read-only | mandatory | Number of packets forwarded by NAT using this translation. |
| 1.3.6.1.4.1.18.3.5.3.2.7.10.1.7 | ColumnwfNatMappingRxCount | read-only | mandatory | Number of packets received by NAT using this translation. |
| 1.3.6.1.4.1.18.3.5.3.2.7.10.1.8 | ColumnwfNatMappingTimeout | read-only | mandatory | The time in seconds since this translation entry was last used. This is used to age out translation entries. |
| 1.3.6.1.4.1.18.3.5.3.2.7.10.1.9 | ColumnwfNatMappingMode | read-only | mandatory | This is the bit mask representing the type of this translation. Each bit specifies the type as follows: The translation could be only ONE of the following thre… |
| 1.3.6.1.4.1.18.3.5.3.2.7.10.1.10 | ColumnwfNatMappingInDomain | read-only | mandatory | This attribute specifies the name of the address domain that this source translation shall be valid for. In ther words, this translation shall only be valid fo… |
| 1.3.6.1.4.1.18.3.5.3.2.7.10.1.11 | ColumnwfNatMappingOutDomain | read-only | mandatory | This attribute specifies the name of the outbound address domain that this translation will be valid for. In other words, this translation only applies to tran… |
| 1.3.6.1.4.1.18.3.5.3.2.7.11 | TablewfNatIntfTable | not-accessible | mandatory | 'The list of configured NAT interfaces.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.11.1 | RowwfNatIntfEntry | not-accessible | mandatory | 'A NAT interface description.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.11.1.1 | ColumnwfNatIntfDelete | read-write | mandatory | This variable determines if a NAT Interface has been configured on the router. |
| 1.3.6.1.4.1.18.3.5.3.2.7.11.1.2 | ColumnwfNatIntfDisable | read-write | mandatory | 'The NAT interface's administrative status. The value 'enabled' denotes that NAT has been configured on the interface. The value 'disabled' denotes that the in… |
| 1.3.6.1.4.1.18.3.5.3.2.7.11.1.3 | ColumnwfNatIntfIpAddress | read-only | mandatory | The IP address of this NAT interface. |
| 1.3.6.1.4.1.18.3.5.3.2.7.11.1.4 | ColumnwfNatIntfCircuit | read-write | mandatory | The circuit number of this interface. |
| 1.3.6.1.4.1.18.3.5.3.2.7.11.1.5 | ColumnwfNatIntfDomain | read-write | mandatory | This attribute specifies the Address Domain Name that this interface is connected to. Unidirectional NAT interfaces should be set with domain name of 'private'… |
| 1.3.6.1.4.1.18.3.5.3.2.7.11.1.6 | ColumnwfNatIntfState | read-only | mandatory | 'The state of NAT on this interface' |
| 1.3.6.1.4.1.18.3.5.3.2.7.11.1.7 | ColumnwfNatIntfTxCount | read-only | mandatory | Number of packets mapped over this interface from the local to the global network.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.11.1.8 | ColumnwfNatIntfRxCount | read-only | mandatory | Number of packets mapped over this interface from the global to the local network.' |
| 1.3.6.1.4.1.18.3.5.3.2.7.11.1.9 | ColumnwfNatIntfPktDropCount | read-only | mandatory | Number of packets dropped on this interface |
| 1.3.6.1.4.1.18.3.5.3.2.7.12 | TablewfNatSrcAddressFilterTable | not-accessible | mandatory | Table of NAT source address filters. |
| 1.3.6.1.4.1.18.3.5.3.2.7.12.1 | RowwfNatSrcAddressFilterEntry | not-accessible | mandatory | Information describing each of the available source address filters. |
| 1.3.6.1.4.1.18.3.5.3.2.7.12.1.1 | ColumnwfNatSrcAddressFilterDelete | read-write | mandatory | Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete a source address filter entry. |
| 1.3.6.1.4.1.18.3.5.3.2.7.12.1.2 | ColumnwfNatSrcAddressFilterDisable | read-write | mandatory | Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable a source address filter entry. |
| 1.3.6.1.4.1.18.3.5.3.2.7.12.1.3 | ColumnwfNatSrcAddressFilterAddress | read-only | mandatory | The IP beginning address of this source address filter entry. |
| 1.3.6.1.4.1.18.3.5.3.2.7.12.1.4 | ColumnwfNatSrcAddressFilterPrefixLen | read-only | mandatory | The number of contiguous bits set in the IP address mask which are used to define the address range of the entry. |
| 1.3.6.1.4.1.18.3.5.3.2.7.12.1.5 | ColumnwfNatSrcAddressFilterIndex | read-only | mandatory | A unique value for this entry in wfNatSrcAddressFilterTable. |
| 1.3.6.1.4.1.18.3.5.3.2.7.12.1.6 | ColumnwfNatSrcAddressFilterNto1Addr | read-write | mandatory | specifies the N-to-1 translation address used for this source address filter, otherwise set to zero. |
| 1.3.6.1.4.1.18.3.5.3.2.7.12.1.7 | ColumnwfNatSrcAddressFilterDomain | read-write | mandatory | The value of this attribute specifies the Address Domain Name that this source address filter is valid for. For Unidirectional NAT this value must be 'public' |
| 1.3.6.1.4.1.18.3.5.3.2.7.12.1.8 | ColumnwfNatSrcAddressFilterTransPoolSelector | read-write | mandatory | The value of this attribute selects where to get the translation address for this source address filter from. This could be either the translation Pool defined… |
| 1.3.6.1.4.1.18.3.5.3.2.7.12.1.9 | ColumnwfNatSrcAddressFilterStaticNextHop | read-write | mandatory | The IP address of the next hop of this source address filter entry. |
| 1.3.6.1.4.1.18.3.5.3.2.7.12.1.10 | ColumnwfNatSrcAddressFilterUnnumCct | read-write | mandatory | This Nat source address filter over the unnumbered interface. |
| 1.3.6.1.4.1.18.3.5.3.2.7.13 | TablewfNatTranslationPoolTable | not-accessible | mandatory | Table of address ranges. |
| 1.3.6.1.4.1.18.3.5.3.2.7.13.1 | RowwfNatTranslationPoolEntry | not-accessible | mandatory | Information describing each of the available translation pool. |
| 1.3.6.1.4.1.18.3.5.3.2.7.13.1.1 | ColumnwfNatTranslationPoolDelete | read-write | mandatory | Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete a translation pool entry. |
| 1.3.6.1.4.1.18.3.5.3.2.7.13.1.2 | ColumnwfNatTranslationPoolDisable | read-write | mandatory | Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable a translation pool entry. |
| 1.3.6.1.4.1.18.3.5.3.2.7.13.1.3 | ColumnwfNatTranslationPoolAddress | read-only | mandatory | The IP beginning address of this translation pool entry. |
| 1.3.6.1.4.1.18.3.5.3.2.7.13.1.4 | ColumnwfNatTranslationPoolPrefixLen | read-only | mandatory | The number of contiguous bits set in the IP address mask which are used to define the address range of the entry. |
| 1.3.6.1.4.1.18.3.5.3.2.7.13.1.5 | ColumnwfNatTranslationPoolIndex | read-only | mandatory | A unique value for this entry in wfNatTranslationPoolTable. |
| 1.3.6.1.4.1.18.3.5.3.2.7.13.1.6 | ColumnwfNatTranslationPoolDomain | read-write | mandatory | The value of this attribute specifies the Address Domain Name that this translation pool is valid for. For Unidirectional NAT this value must be 'public' |