XYLO-ANNEX-MIB
300 objects
No module-level DESCRIPTION found.
Imported Objects
| RFC-1212 | OBJECT-TYPE |
| RFC1155-SMI | Counter Gauge IpAddress TimeTicks |
| RFC1213-MIB | DisplayString PhysAddress |
| XYLO-MIB-SMI | annexcmds annexconfig anxccpstats anxchas anxchascommon anxgrestats anxgsystats anxPPPStats hw igmp ippool l2tp radiusAccClient radiusAuthClient radiusConfig radiusStats sw |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.2.1.67.1.2.1.1.1 | ScalarradiusAuthClientInvalidServerAddresses | read-only | mandatory | The total number of RADIUS Access-Response packets received from unknown addresses since client start-up. |
| 1.3.6.1.2.1.67.1.2.1.1.2 | ScalarradiusAuthClientIdentifier | read-only | mandatory | The NAS-Identifier of the RADIUS authentication client. |
| 1.3.6.1.2.1.67.1.2.1.1.3 | TableradiusAuthServerTable | not-accessible | mandatory | The (conceptual) table listing the RADIUS authentication servers with which the client shares a secret. |
| 1.3.6.1.2.1.67.1.2.1.1.3.1 | RowradiusAuthServerEntry | not-accessible | mandatory | An entry (conceptual row) representing a RADIUS authentication server with which the client shares a secret. |
| 1.3.6.1.2.1.67.1.2.1.1.3.1.1 | ColumnradiusAuthServerIndex | read-only | mandatory | The RADIUS authentication server with which the client interacts. |
| 1.3.6.1.2.1.67.1.2.1.1.3.1.2 | ColumnradiusAuthServerAddress | read-only | mandatory | The IP address of the RADIUS authentication server referred to in this table entry. |
| 1.3.6.1.2.1.67.1.2.1.1.3.1.3 | ColumnradiusAuthClientServerPortNumber | read-only | mandatory | The UDP port the client is using to send requests to this server. |
| 1.3.6.1.2.1.67.1.2.1.1.3.1.4 | ColumnradiusAuthClientRoundTripTime | read-only | mandatory | The total roundtrip time of the last packet sent between the authentication client and the RADIUS server referred to in this table entry. |
| 1.3.6.1.2.1.67.1.2.1.1.3.1.5 | ColumnradiusAuthClientAccessRequests | read-only | mandatory | The total number of RADIUS Access-Request packets sent to this server since client start-up. This does not include retransmissions. |
| 1.3.6.1.2.1.67.1.2.1.1.3.1.6 | ColumnradiusAuthClientAccessRetransmissions | read-only | mandatory | The total number of RADIUS Access-Request packets retransmitted to the same server since client start-up. |
| 1.3.6.1.2.1.67.1.2.1.1.3.1.7 | ColumnradiusAuthClientAccessAccepts | read-only | mandatory | The total number of RADIUS Access-Accept packets received from this server since client start-up. |
| 1.3.6.1.2.1.67.1.2.1.1.3.1.8 | ColumnradiusAuthClientAccessRejects | read-only | mandatory | The total number of RADIUS Access-Reject packets received from this server since client start-up. |
| 1.3.6.1.2.1.67.1.2.1.1.3.1.9 | ColumnradiusAuthClientAccessChallenges | read-only | mandatory | The total number of RADIUS Access-Challenge packets received from this server since client start-up. |
| 1.3.6.1.2.1.67.1.2.1.1.3.1.10 | ColumnradiusAuthClientMalformedAccessResponses | read-only | mandatory | The total number of malformed RADIUS Access-Response packets received from this server since client start-up. Bad authenticators are not included as malformed … |
| 1.3.6.1.2.1.67.1.2.1.1.3.1.11 | ColumnradiusAuthClientAuthenticationBadAuthenticators | read-only | mandatory | The total number of RADIUS Access-Response packets containing invalid authenticators received from this server since client start-up. |
| 1.3.6.1.2.1.67.1.2.1.1.3.1.12 | ColumnradiusAuthClientAuthenticationPendingRequests | read-only | mandatory | The total number of RADIUS Access-Request packets destined for this server that have not yet timed out or received a response. This variable is incremented whe… |
| 1.3.6.1.2.1.67.1.2.1.1.3.1.13 | ColumnradiusAuthClientAuthenticationTimeouts | read-only | mandatory | The total number of authentication timeouts to this server since client startup. After a timeout the client may retry to the same server, send to a different s… |
| 1.3.6.1.2.1.67.1.2.1.1.3.1.14 | ColumnradiusAuthClientUnknownType | read-only | mandatory | The total number of RADIUS packets of unknown type which were received from this server on the authentication port since client start-up. |
| 1.3.6.1.2.1.67.2.2.1.1.1 | ScalarradiusAccClientInvalidServerAddresses | read-only | mandatory | The total number of RADIUS Accounting-Response packets received from unknown addresses since client start-up. |
| 1.3.6.1.2.1.67.2.2.1.1.2 | ScalarradiusAccClientIdentifier | read-only | mandatory | The NAS-Identifier of the RADIUS accounting client. |
| 1.3.6.1.2.1.67.2.2.1.1.3 | TableradiusAccServerTable | not-accessible | mandatory | The (conceptual) table listing the RADIUS accounting servers with which the client shares a secret. |
| 1.3.6.1.2.1.67.2.2.1.1.3.1 | RowradiusAccServerEntry | not-accessible | mandatory | An entry (conceptual row) representing a RADIUS accounting server with which the client shares a secret. |
| 1.3.6.1.2.1.67.2.2.1.1.3.1.1 | ColumnradiusAccServerIndex | read-only | mandatory | The RADIUS accounting server with which the client interacts. |
| 1.3.6.1.2.1.67.2.2.1.1.3.1.2 | ColumnradiusAccServerAddress | read-only | mandatory | The IP address of the RADIUS accounting server referred to in this table entry. |
| 1.3.6.1.2.1.67.2.2.1.1.3.1.3 | ColumnradiusAccClientServerPortNumber | read-only | mandatory | The UDP port the client is using to send requests to this server. |
| 1.3.6.1.2.1.67.2.2.1.1.3.1.4 | ColumnradiusAccClientRoundTripTime | read-only | mandatory | The total roundtrip time of the last packet sent between the accounting client and the RADIUS server referred to in this table entry. |
| 1.3.6.1.2.1.67.2.2.1.1.3.1.5 | ColumnradiusAccClientAccountingRequests | read-only | mandatory | The total number of RADIUS Accounting-Request packets sent since client start-up. This does not include retransmissions. |
| 1.3.6.1.2.1.67.2.2.1.1.3.1.6 | ColumnradiusAccClientAccountingRetransmissions | read-only | mandatory | The total number of RADIUS Accounting-Request packets retransmitted to the same server since client start-up. Retransmissions include retries where the Identif… |
| 1.3.6.1.2.1.67.2.2.1.1.3.1.7 | ColumnradiusAccClientAccountingResponses | read-only | mandatory | The total number of RADIUS Accounting-Response packets received from this server since client start-up. |
| 1.3.6.1.2.1.67.2.2.1.1.3.1.8 | ColumnradiusAccClientMalformedAccountingResponses | read-only | mandatory | The total number of malformed RADIUS Accounting-Response packets received from this server since client start-up. Bad authenticators are not included as malfor… |
| 1.3.6.1.2.1.67.2.2.1.1.3.1.9 | ColumnradiusAccClientAccountingBadAuthenticators | read-only | mandatory | The total number of RADIUS Accounting-Response packets which contained invalid authenticators received from this server since client start-up. |
| 1.3.6.1.2.1.67.2.2.1.1.3.1.10 | ColumnradiusAccClientAccountingPendingRequests | read-only | mandatory | The total number of RADIUS Accounting-Request packets sent to this server that have not yet timed out or received a response. This variable is incremented when… |
| 1.3.6.1.2.1.67.2.2.1.1.3.1.11 | ColumnradiusAccClientAccountingTimeouts | read-only | mandatory | The total number of accounting timeouts to this server since client startup. After a timeout the client may retry to the same server, send to a different serve… |
| 1.3.6.1.2.1.67.2.2.1.1.3.1.12 | ColumnradiusAccClientUnknownType | read-only | mandatory | The total number of RADIUS packets of unknown type which were received from this server on the accounting port since client start-up. |
| 1.3.6.1.4.1.15.2.1.1 | ScalarhwType | read-only | mandatory | An identifier for the Annex hardware type. |
| 1.3.6.1.4.1.15.2.1.2 | ScalarhwRev | read-only | mandatory | The revision level of the hardware platform. |
| 1.3.6.1.4.1.15.2.1.3 | ScalarromRev | read-only | mandatory | The revision number of the ROM Monitor software. |
| 1.3.6.1.4.1.15.2.1.4 | ScalarserialNumber | read-only | deprecated | The serial number assigned to the unit. This object is deprecated in the R9.0 software and is replaced by the macAddress object below. |
| 1.3.6.1.4.1.15.2.1.5 | ScalarmemorySize | read-only | mandatory | The amount of memory present in the unit. |
| 1.3.6.1.4.1.15.2.1.6 | Scalare2Size | read-only | mandatory | The size of EEPROM present in the unit, reported in KB. EEPROM is used to store configuration parameters and filter definitions for all platforms. Self boot un… |
| 1.3.6.1.4.1.15.2.1.7 | ScalarflashSize | read-only | mandatory | The size of the FLASH memory in the unit, reported in MB. If the ROM revision in the unit is less than 0750, the size is not available and is reported as zero.… |
| 1.3.6.1.4.1.15.2.1.8 | ScalarnetHwType | read-only | mandatory | The type of LAN interface hardware in the unit. |
| 1.3.6.1.4.1.15.2.1.9 | ScalarmacAddress | read-only | mandatory | The serial number assigned to the unit is now the MAC address. |
| 1.3.6.1.4.1.15.2.1.10 | Scalartotalmodems | read-only | mandatory | The total number of internal modems on the board. Incase of having more than 1 T1 engines this will be the sum of all the internal modems per T1 engines. Note:… |
| 1.3.6.1.4.1.15.2.1.11 | ScalarcompressionCardHwRev | read-only | mandatory | The compression card hardware revision for 5399 and ra8000 platforms. If the card is not present the string -not present- will be returned. |
| 1.3.6.1.4.1.15.2.2.1 | ScalarswType | read-only | mandatory | The software version currently running on the Annex. |
| 1.3.6.1.4.1.15.2.2.2 | ScalarswRevMajor | read-only | mandatory | The major software release number. |
| 1.3.6.1.4.1.15.2.2.3 | ScalarswRevMinor | read-only | mandatory | The minor software release number. |
| 1.3.6.1.4.1.15.2.2.4 | ScalarswBuild | read-only | mandatory | The full name of the software build, including the software version, major and minor version numbers and the date and time of the build. |
| 1.3.6.1.4.1.15.2.2.5 | ScalarimageName | read-only | mandatory | The name of the most recently booted image. |
| 1.3.6.1.4.1.15.2.2.6 | ScalarbootHost | read-only | mandatory | The Internet address of the host from which the Annex booted. |
| 1.3.6.1.4.1.15.2.2.7 | ScalardefaultDomain | read-only | mandatory | The default domain name provided by the DNS nameserver. |
| 1.3.6.1.4.1.15.2.2.8 | ScalarcurrentDate | read-only | mandatory | The current date and time provided by the time server. |
| 1.3.6.1.4.1.15.2.2.9 | ScalarusableMemory | read-only | mandatory | The amount of available for data buffers and other structures after the Annex has booted. |
| 1.3.6.1.4.1.15.2.2.10 | ScalarfreeMemory | read-only | mandatory | The amount of currently available memory. |
| 1.3.6.1.4.1.15.2.2.11 | ScalarminFreeMemory | read-only | mandatory | The minimum amount of free memory since booting the Annex. |
| 1.3.6.1.4.1.15.2.2.12 | ScalarcpuUtilization | read-only | mandatory | Percent of CPU time currently being used. |
| 1.3.6.1.4.1.15.2.2.13 | ScalarmaxProcs | read-only | mandatory | The total number of process structures allocated for use. |
| 1.3.6.1.4.1.15.2.2.14 | ScalarmostProcs | read-only | mandatory | The maximum number of active processes since the Annex was booted. |
| 1.3.6.1.4.1.15.2.2.15 | ScalaractiveProcs | read-only | mandatory | The number of currently active processes. |
| 1.3.6.1.4.1.15.2.2.16 | ScalarcpuIRescheds | read-only | mandatory | The number of processes whose time slice has expired in the last minute. |
| 1.3.6.1.4.1.15.2.2.17 | ScalarcpuTRescheds | read-only | mandatory | The total number of processes whose time slice has expired since booting the Annex. |
| 1.3.6.1.4.1.15.2.2.18 | ScalarcontextISwtchs | read-only | mandatory | The number of context switches in the last minute. |
| 1.3.6.1.4.1.15.2.2.19 | ScalarcontextTSwtchs | read-only | mandatory | The total number of context switches since booting the Annex. |
| 1.3.6.1.4.1.15.2.2.20 | ScalarcpuIActivates | read-only | mandatory | The number of processes that were activated in the last minute. |
| 1.3.6.1.4.1.15.2.2.21 | ScalarcpuTActivates | read-only | mandatory | The number of processes that were activated since booting the Annex. |
| 1.3.6.1.4.1.15.2.2.22 | ScalarmaxCallouts | read-only | mandatory | The number of allocated Callout structures for timed events in the Annex. |
| 1.3.6.1.4.1.15.2.2.23 | ScalarleastCallouts | read-only | mandatory | The minimum number of Callout structures available since last booting the Annex. |
| 1.3.6.1.4.1.15.2.2.24 | ScalarfreeCallouts | read-only | mandatory | The current number of free Callout structures. |
| 1.3.6.1.4.1.15.2.2.25 | ScalartotalMbufs | read-only | mandatory | The total number of mbufs allocated by the Annex kernel. |
| 1.3.6.1.4.1.15.2.2.26 | ScalarfreeMbufs | read-only | mandatory | The number of currently available mbufs. |
| 1.3.6.1.4.1.15.2.2.27 | ScalarleastMbufs | read-only | mandatory | The least number of mbufs available at any time since the last reboot of the Annex. |
| 1.3.6.1.4.1.15.2.2.28 | ScalardeniedMbufs | read-only | mandatory | The number of times that a process requested an mbuf and was denied since there were none available. |
| 1.3.6.1.4.1.15.2.2.31 | ScalarswAFDStatus | read-only | mandatory | An indication of the current status of the Automated FIrmware Download (AFD) facility. Please refer to the syslog for detailed status or error information. The… |
| 1.3.6.1.4.1.15.2.5.1 | ScalaranxInetAddr | read-write | mandatory | The Internet address of the Annex. This MIB object corresponds to the NA/admin Annex parameter 'inet_addr'. |
| 1.3.6.1.4.1.15.2.5.2 | ScalaranxPrefLoadAddr | read-write | mandatory | The preferred load address for the Annex. This MIB object corresponds to the NA/admin Annex parameter 'pref_load_addr'. |
| 1.3.6.1.4.1.15.2.5.3 | ScalaranxPrefDumpAddr | read-write | mandatory | The preferred dump address for the Annex. This MIB object corresponds to the NA/admin Annex parameter 'pref_dump_addr'. |
| 1.3.6.1.4.1.15.2.5.4 | ScalaranxLoadDumpGateway | read-write | mandatory | The Internet address of a gateway used when the preferred load or dump host is on a different network or subnet. This MIB object corresponds to the NA/admin An… |
| 1.3.6.1.4.1.15.2.5.5 | ScalaranxLoadDumpSeq | read-write | mandatory | Lists the available network interfaces and the order that the Annex uses them when doing a down-line load or up-line dump. The list may consist of one or more … |
| 1.3.6.1.4.1.15.2.5.6 | ScalaranxLoadBcast | read-write | mandatory | This parameter defines whether the Annex broadcasts for the config or the motd files if they were not found on the preferred load host. This MIB object corresp… |
| 1.3.6.1.4.1.15.2.5.7 | ScalaranxServerCap | read-write | mandatory | Defines whether the Annex can act as a file server host for another Annex. The allowable values are 'all', 'none' (the default), or one or more of the followin… |
| 1.3.6.1.4.1.15.2.5.8 | ScalaranxTimeBcast | read-write | mandatory | This parameter defines whether the Annex broadcasts for the time if the preferred load host does not provide a time server. This MIB object corresponds to the … |
| 1.3.6.1.4.1.15.2.5.9 | ScalaranxBcastAddr | read-write | mandatory | The Internet address used by the Annex when sending broadcasts. This MIB object corresponds to the NA/admin Annex parameter 'broadcast_addr'. |
| 1.3.6.1.4.1.15.2.5.10 | ScalaranxSubnetMask | read-write | mandatory | The Internet subnet mask for the Annex. Setting this object to 0.0.0.0 results in the default of 255.0.0.0 actually being set. This MIB object corresponds to t… |
| 1.3.6.1.4.1.15.2.5.11 | ScalaranxAuthAgent | read-write | mandatory | This parameter controls whether the Annex can send an ICMP Address Mask Reply to a received ICMP Address Mask Request. This MIB object corresponds to the NA/ad… |
| 1.3.6.1.4.1.15.2.5.12 | ScalaranxMaxVcli | read-write | mandatory | The maximum number of virtual CLI connections allowed by the Annex at any one time. 0 means the Annex does not allow VCLI connections. 255 allows the Annex to … |
| 1.3.6.1.4.1.15.2.5.13 | ScalaranxIpEncapType | read-write | mandatory | This parameter specifies whether the Annex encapsulates IP packets in the Ethernet format or the IEEE 802.2/802.3 Data Link Layer format. This MIB object corre… |
| 1.3.6.1.4.1.15.2.5.14 | ScalaranxNameServer1Type | read-write | mandatory | The name service type used by the primary nameserver host. This MIB object corresponds to the NA/admin Annex parameter 'name_server_1'. |
| 1.3.6.1.4.1.15.2.5.15 | ScalaranxNameServer1Addr | read-write | mandatory | The Internet address of the primary nameserver host. This MIB object corresponds to the NA/admin Annex parameter 'pref_name1_addr'. |
| 1.3.6.1.4.1.15.2.5.16 | ScalaranxNameServer2Type | read-write | mandatory | The name service type used by the secondary nameserver host. This MIB object corresponds to the NA/admin Annex parameter 'name_server_2'. |
| 1.3.6.1.4.1.15.2.5.17 | ScalaranxNameServer2Addr | read-write | mandatory | The Internet address of the secondary nameserver host. This MIB object corresponds to the NA/admin Annex parameter 'pref_name2_addr'. |
| 1.3.6.1.4.1.15.2.5.18 | ScalaranxNameServerBcast | read-write | mandatory | This parameter controls whether the Annex broadcasts a name server request if the preferred name servers do not respond. This MIB object corresponds to the NA/… |
| 1.3.6.1.4.1.15.2.5.19 | ScalaranxRwhod | read-write | mandatory | Defines whether the Annex listens for RWHO broadcasts when building its host table. This MIB object corresponds to the NA/admin Annex parameter 'rwhod'. |
| 1.3.6.1.4.1.15.2.5.20 | ScalaranxMinUniqueHostNames | read-write | mandatory | Defines whether the Annex minimum uniqueness feature is available. This MIB object corresponds to the NA/admin Annex parameter 'min_unique_hostnames'. |
| 1.3.6.1.4.1.15.2.5.21 | ScalaranxHostTableSize | read-write | mandatory | Defines the number of entries in the Annex host table. A value of 254 indicates no host table. A value of 255 sets no limit on the size of the table. This MIB … |
| 1.3.6.1.4.1.15.2.5.22 | ScalaranxRouted | read-write | mandatory | Defines whether the RIP routing daemon on the Annex is enabled. Enabling the routing daemon activates both passive and active RIP if the anxOptionKey parameter… |
| 1.3.6.1.4.1.15.2.5.23 | ScalaranxEnableSecurity | read-write | mandatory | This parameter controls whether the Annex security system is enabled. This MIB object corresponds to the NA/admin Annex parameter 'enable_security'. |
| 1.3.6.1.4.1.15.2.5.24 | ScalaranxPassword | read-write | mandatory | Setting this parameter changes the Annex's administration password. Reading this parameter will return either <set> if the password is defined or <unset> if th… |
| 1.3.6.1.4.1.15.2.5.25 | ScalaranxSecurServer1Addr | read-write | mandatory | The Internet address of the primary host where the Annex sends its security requests. This MIB object corresponds to the NA/admin Annex parameter 'pref_secure1… |
| 1.3.6.1.4.1.15.2.5.26 | ScalaranxSecurServer2Addr | read-write | mandatory | The Internet address of the secondary host where the Annex sends its security requests. This MIB object corresponds to the NA/admin Annex parameter 'pref_secur… |
| 1.3.6.1.4.1.15.2.5.27 | ScalaranxNetTurnAround | read-write | mandatory | The amount of time (in seconds) that the Annex waits for a response from a security server. This MIB object corresponds to the NA/admin Annex parameter 'networ… |
| 1.3.6.1.4.1.15.2.5.28 | ScalaranxSecurBcast | read-write | mandatory | This parameter controls whether the Annex will broadcast its security requests when neither of the preferred security servers are available. This MIB object co… |
| 1.3.6.1.4.1.15.2.5.29 | ScalaranxVcliSecurity | read-write | mandatory | This parameter controls whether the Annex performs user validation on the virtual CLI connections. This MIB object corresponds to the NA/admin Annex parameter … |
| 1.3.6.1.4.1.15.2.5.30 | ScalaranxVcliPassword | read-write | mandatory | This parameter defines a password used by the Annex when setting up a virtual CLI connection. This MIB object corresponds to the NA/admin Annex parameter 'vcli… |
| 1.3.6.1.4.1.15.2.5.31 | ScalaranxAcpKey | read-write | mandatory | This parameter defines the Annex's encryption key used when exchanging messages between the Annex and the security server. This MIB object corresponds to the N… |
| 1.3.6.1.4.1.15.2.5.32 | ScalaranxSysLogMask | read-write | mandatory | Defines the priority levels of events logged in the Annex syslog file. The allowable values are 'all', 'none', or one or more of the following level names sepa… |
| 1.3.6.1.4.1.15.2.5.33 | ScalaranxSysLogFacility | read-write | mandatory | This parameter defines the 4.3BSD syslog facility used in logging the Annex messages. This MIB object corresponds to the NA/admin Annex parameter 'syslog_facil… |
| 1.3.6.1.4.1.15.2.5.34 | ScalaranxSysLogHost | read-write | mandatory | The Internet address of the host configured to log Annex messages. This MIB object corresponds to the NA/admin Annex parameter 'syslog_host'. |
| 1.3.6.1.4.1.15.2.5.35 | ScalaranxCliPrompt | read-write | mandatory | This parameter defines the prompt string for all CLI users. The prompt string consists of displayable characters and embedded formatting codes. Each formatting… |
| 1.3.6.1.4.1.15.2.5.36 | ScalaranxMotdFile | read-write | mandatory | The host file name that contains the message-of-the-day for the Annex. This MIB object corresponds to the NA/admin Annex parameter 'motd_file'. |
| 1.3.6.1.4.1.15.2.5.37 | ScalaranxTftpDirName | read-write | mandatory | Specifies the directory name to be prepended to all files (boot image, motd, macros, etc.) when booting via TFTP. This MIB object corresponds to the NA/admin A… |
| 1.3.6.1.4.1.15.2.5.38 | ScalaranxTftpDumpName | read-write | mandatory | The full pathname of the TFTP dump file, if any. This MIB object corresponds to the NA/admin Annex parameter 'tftp_dump_name'. |
| 1.3.6.1.4.1.15.2.5.39 | ScalaranxTimeZone | read-write | mandatory | Defines the timezone where the Annex resides in minutes west of GMT. This MIB object corresponds to the NA/admin Annex parameter 'timezone_minuteswest'. |
| 1.3.6.1.4.1.15.2.5.40 | ScalaranxDaylightSavings | read-write | mandatory | Defines the daylight savings time for the geographic location of the Annex. This MIB object corresponds to the NA/admin Annex parameter 'daylight_savings'. |
| 1.3.6.1.4.1.15.2.5.41 | ScalaranxLatKey | read-write | deprecated | The Annex specific LAT key used to enable or disable the LAT protocol. If this value is not correct, and the LAT protocol is disabled, none of the other LAT re… |
| 1.3.6.1.4.1.15.2.5.42 | ScalaranxCircuitTimer | read-write | deprecated | The time interval in tens of milliseconds between the transmission of LAT packets. This MIB object corresponds to the NA/admin Annex parameter 'circuit_timer'. |
| 1.3.6.1.4.1.15.2.5.43 | ScalaranxFacilityNum | read-write | deprecated | The LAT facility number. This MIB object corresponds to the NA/admin Annex parameter 'facility_num'. |
| 1.3.6.1.4.1.15.2.5.44 | ScalaranxLatGroupVal | read-write | deprecated | The Annex LAT group code for permitting access to LAT services. To access a specific LAT service, the Annex must have at least one enabled group code match the… |
| 1.3.6.1.4.1.15.2.5.45 | ScalaranxKeepAliveTimer | read-write | deprecated | The time interval, in seconds, between the transmission of identification packets during times of network inactivity. This MIB object corresponds to the NA/adm… |
| 1.3.6.1.4.1.15.2.5.46 | ScalaranxReXmitLimit | read-write | deprecated | The number of times to retransmit a packet before notifying the user of a network failure. This MIB object corresponds to the NA/admin Annex parameter 'retrans… |
| 1.3.6.1.4.1.15.2.5.47 | ScalaranxServerName | read-write | deprecated | A string of up to 16 characters used to name the Annex in the LAT protocol. This MIB object corresponds to the NA/admin Annex parameter 'server_name'. |
| 1.3.6.1.4.1.15.2.5.48 | ScalaranxServiceLimit | read-write | deprecated | This parameter defines the upper bound on the number of services that the Annex can maintain in its local service table. This MIB object corresponds to the NA/… |
| 1.3.6.1.4.1.15.2.5.49 | ScalaranxConfigFile | read-write | mandatory | The name of the host file that contains the alias and menu entries. This MIB object corresponds to the NA/admin Annex parameter 'config_file'. |
| 1.3.6.1.4.1.15.2.5.50 | ScalaranxLatVcliGroupVal | read-write | deprecated | This Annex parameter specifies which remote group codes are accessible to virtual cli users. All virtual cli users have the same group code. The syntax is a se… |
| 1.3.6.1.4.1.15.2.5.51 | ScalaranxLatQueueMax | read-write | deprecated | Defines the maximum number of host requests (HIC's) that the Annex will save in its internal queue when the requested resource is not available (port busy). Th… |
| 1.3.6.1.4.1.15.2.5.52 | ScalaranxLatLocation | read-write | deprecated | A string of up to 32 characters used to identify the location of the Annex for the LAT protocol. This MIB object corresponds to the NA/admin Annex parameter 's… |
| 1.3.6.1.4.1.15.2.5.53 | ScalaranxDisabledModules | read-write | mandatory | Defines which selectable modules are currently disabled. The allowable values are 'all', 'none' or one or more of the following names separated by commas: 'adm… |
| 1.3.6.1.4.1.15.2.5.54 | ScalaranxSysLogPort | read-write | mandatory | Specifies the Annex serial port number where syslog messages are sent. If set to 0, syslog messages are not sent to an Annex port. This is independent of any h… |
| 1.3.6.1.4.1.15.2.5.55 | ScalaranxOptionKey | read-write | deprecated | The Annex specific software option key used to enable or disable the AppleTalk, dynamic routing and TN3270 support. This MIB object corresponds to the NA/admin… |
| 1.3.6.1.4.1.15.2.5.56 | ScalaranxIpFwdBcast | read-write | mandatory | When enabled, all broadcasted IP packets are forwarded to all interfaces. This MIB object corresponds to the NA/admin Annex parameter 'ip_forward_broadcast'. |
| 1.3.6.1.4.1.15.2.5.57 | ScalaranxLooseSrcRoute | read-write | mandatory | When enabled, the Annex allows internet loose source routing. This MIB object corresponds to the NA/admin Annex parameter 'loose_source_route'. |
| 1.3.6.1.4.1.15.2.5.58 | ScalaranxAppleTalkRouter | read-write | deprecated | The Ethernet address of the AppleTalk router. The default value is 0-0-0-0-0-0. Each part of the address must be a hex value separated by a dash. This MIB obje… |
| 1.3.6.1.4.1.15.2.5.59 | ScalaranxAppleTalkDefZones | read-write | deprecated | The comma separated list of AppleTalk zone names used as a default when ACP cannot supply the actual set of zone names. Commas, spaces and double quotes can be… |
| 1.3.6.1.4.1.15.2.5.60 | ScalaranxAppleTalkNodeId | read-write | mandatory | The AppleTalk node ID that the Annex first tries to use at startup. The address consists of two parts separated by a dot. The address may be in either hex or d… |
| 1.3.6.1.4.1.15.2.5.61 | ScalaranxAppleTalkZone | read-write | mandatory | The zone name that the Annex first tries to use at startup. Spaces and double quotes can be used in the zone name by preceding these characters with a backslas… |
| 1.3.6.1.4.1.15.2.5.62 | ScalaranxRipRouteList | read-write | mandatory | A list of one to eight IP addresses in dotted address format (ddd.ddd.ddd.ddd) with comma separators between the addresses. This list defines where RIP respons… |
| 1.3.6.1.4.1.15.2.5.63 | ScalaranxRipAuth | read-write | mandatory | This is a clear text password that is used to authenticate the RIP packets. If the NULL string is specified, RIP packet authentication is turned off and all RI… |
| 1.3.6.1.4.1.15.2.5.64 | ScalaranxTcpKeepAlive | read-write | mandatory | The default keep-alive value in minutes for connections to this Annex. If this is zero, use the default value of 120 minutes. If set to 255, then the keep-aliv… |
| 1.3.6.1.4.1.15.2.5.65 | ScalaranxMaxModemCalls | read-write | mandatory | The number of calls for which modem call accounting information is kept. The default value is 20. |
| 1.3.6.1.4.1.15.2.5.66 | ScalaranxOutputTtl | read-write | mandatory | The value that is placed in the ttl field of all locally generated IP packets. The default value is 64. This MIB object corresponds to the NA/admin Annex param… |
| 1.3.6.1.4.1.15.2.5.67 | ScalaranxSessionLimit | read-write | mandatory | The maximum number of sessions allowed on the Annex. The default is 1152. The maximum value that can be set is actually 16 times the maximun number of ports on… |
| 1.3.6.1.4.1.15.2.5.68 | ScalaranxLockEnable | read-write | mandatory | When enabled, allows any port user to use the LOCK DECServer command. The default value is enabled. This MIB object corresponds to the NA/admin Annex parameter… |
| 1.3.6.1.4.1.15.2.5.69 | ScalaranxPasswdLimit | read-write | mandatory | Defines the maximum number of times a user on a port can attempt to enter a password before the Annex resets the port. Setting this object to 0 results in a de… |
| 1.3.6.1.4.1.15.2.5.70 | ScalaranxLatMulticastTimer | read-write | deprecated | The elapsed time in seconds between transmission of service announcements. The default value is 30 seconds. This MIB object corresponds to the NA/admin Annex p… |
| 1.3.6.1.4.1.15.2.5.71 | ScalaranxChapAuthname | read-write | mandatory | The name associated with the Annex that is used to fill the Name field in the PPP CHAP challenge message. If this value is a zero length string, the Annex will… |
| 1.3.6.1.4.1.15.2.5.72 | ScalaranxTimeServerAddr | read-write | mandatory | The Internet address of the time server host. This MIB object corresponds to the NA/admin Annex parameter 'time_server'. |
| 1.3.6.1.4.1.15.2.5.78 | ScalaranxMopPrefHost | read-write | deprecated | The Ethernet address of the preferred MOP load/dump host. The default value is 0-0-0-0-0-0. Each part of the address must be a hex value separated by a dash. T… |
| 1.3.6.1.4.1.15.2.5.79 | ScalaranxMopPassword | read-write | deprecated | The 8 byte hexadecimal MOP maintenance password. Each byte is represented by two hex digits in the string. This MIB object corresponds to the NA/admin Annex pa… |
| 1.3.6.1.4.1.15.2.5.80 | ScalaranxMopLoginPassword | read-write | deprecated | The password for all ports where anxpCliInterface parameter is set to vci and anxpVciLoginPortPassword is enabled. The default value is 'ACCESS'. Reading this … |
| 1.3.6.1.4.1.15.2.5.81 | ScalaranxMopLoginPrompt | read-write | deprecated | The password prompt for all ports whose anxpCliInterface parameter is set to vci. The default is '#'. This MIB object corresponds to the NA/admin Annex paramet… |
| 1.3.6.1.4.1.15.2.5.82 | ScalaranxMopLoginTimer | read-write | deprecated | The inactivity timer for all ports whose anxpCliInterface parameter is set to vci. Setting this object to 0 results in a default value of 30 minutes. This MIB … |
| 1.3.6.1.4.1.15.2.5.83 | ScalaranxIpxFrameType | read-write | mandatory | The framing used for IPX protocol packets. The default value is raw802. This MIB object corresponds to the NA/admin Annex parameter 'ipx_frame_type'. |
| 1.3.6.1.4.1.15.2.5.89 | ScalaranxTmuxEnable | read-write | deprecated | Controls whether the Annex uses TMux to multiplex small TCP or UDP packets into a single IP packet. The host must also support TMux, otherwise the Annex will d… |
| 1.3.6.1.4.1.15.2.5.90 | ScalaranxTmuxMaxHost | read-write | deprecated | The maximum size of the Tmux address table. If the number of host addresses exceeds this limit, the oldest entry is flushed. The default value is 64. This MIB … |
| 1.3.6.1.4.1.15.2.5.91 | ScalaranxTmuxMaxMpx | read-write | deprecated | The largest packet that can be placed in a TMux packet. Larger packets are not multiplexed but are directly passed to the IP layer. The default value is 700. T… |
| 1.3.6.1.4.1.15.2.5.92 | ScalaranxTmuxDelay | read-write | deprecated | The maximum amount of time used to accumulate smaller packets into a larger packet. When the time expires, the multiplexed packet is sent, regardless how large… |
| 1.3.6.1.4.1.15.2.5.93 | ScalaranxAllowSets | read-only | mandatory | This object will return whether SNMP manager(client) has access to read or read-write the MIB objects. The access is determined by NA/admin parameter allow_snm… |
| 1.3.6.1.4.1.15.2.5.94 | ScalaranxDefaultImageName | read-write | mandatory | The name of the image file that is loaded by default when booting the Annex. This MIB object corresponds to the NA/admin Annex parameter 'image_name'. |
| 1.3.6.1.4.1.15.2.5.95 | ScalaranxLatGroupMap | read-write | deprecated | This parameter is functionally identical to anxLatGroupVal and corresponds to the NA/admin Annex parameter 'group_value'. The syntax of this object is an octet… |
| 1.3.6.1.4.1.15.2.5.96 | ScalaranxLatVcliGroupMap | read-write | deprecated | This parameter is functionally identical to anxLatVcliGroupVal and corresponds to the NA/admin Annex parameter 'vcli_groups'. The syntax of this object is an o… |
| 1.3.6.1.4.1.15.2.5.97 | ScalaranxMultiSession | read-write | deprecated | This parameter allows multisession operation to be managed on a terminal server basis. It tells that the server is configured for multisession operation. Once … |
| 1.3.6.1.4.1.15.2.5.98 | ScalaranxVcliInactivity | read-write | mandatory | This parameter will specify the amount of time in minutes that a vcli session can remain inactive. If the timer expires, the annex will terminate the virtual s… |
| 1.3.6.1.4.1.15.2.5.99 | ScalaranxDHCPServer1Addr | read-write | mandatory | The Internet address of the primary DHCP server host. This MIB object corresponds to the NA/admin Annex parameter `pref_DHCP1_addr'. |
| 1.3.6.1.4.1.15.2.5.100 | ScalaranxDHCPServer2Addr | read-write | mandatory | The Internet address of the secondary DHCP server host. This MIB object corresponds to the NA/admin Annex parameter `pref_DHCP2_addr'. |
| 1.3.6.1.4.1.15.2.5.101 | ScalaranxDHCPServerBcast | read-write | mandatory | This parameter controls whether the Annex broadcasts a DHCPDISCOVER request if the preferred DHCP servers do not respond. This MIB object corresponds to the NA… |
| 1.3.6.1.4.1.15.2.5.102 | ScalaranxConfigServer | read-only | mandatory | The IP address of the host from where the config file was downloaded. |
| 1.3.6.1.4.1.15.2.5.103 | ScalaranxMaxChapChallInt | read-write | mandatory | Specifies maximum value for the random CHAP re-challenge interval. Valid values are in range of 0 to 65535 seconds. Value of 0 for this parameter will turn off… |
| 1.3.6.1.4.1.15.2.5.104 | ScalaranxMMPEnable | read-write | mandatory | Enables or disables MMP in the Remote Annex. This MIB object corresponds to the NA/admin parameter mmp_enabled. |
| 1.3.6.1.4.1.15.2.5.106 | ScalaranxModulesDisabled | read-write | mandatory | A bit array that contains the setting of selectable modules that are currently disabled. The allowable values are: 0x00000001 - admin 0x00000002 - tstty 0x0000… |
| 1.3.6.1.4.1.15.2.5.107 | ScalarsecurityProtocol | read-write | mandatory | Values of this object can either be set to acp or radius to indicate which protocol this annex will use. Change of this parameter will not be effective, even w… |
| 1.3.6.1.4.1.15.2.5.108 | ScalaranxRipForceNewrt | read-write | mandatory | When enabled, this parameter specifies the timeout value in seconds that the Annex waits for a router to send periodic RIP updates. If the Annex does not hear … |
| 1.3.6.1.4.1.15.2.5.109 | ScalaranxNbnServer1Addr | read-write | mandatory | The Internet address of the primary NetBIOS nameserver host. This MIB object corresponds to the NA/admin Annex parameter 'pref_nbns1_addr'. |
| 1.3.6.1.4.1.15.2.5.110 | ScalaranxNbnServer2Addr | read-write | mandatory | The Internet address of the secondary NetBIOS nameserver host. This MIB object corresponds to the NA/admin Annex parameter 'pref_nbns2_addr'. |
| 1.3.6.1.4.1.15.2.5.111 | ScalaranxNameserverOverride | read-write | mandatory | Indicates whether or not to override the PPP Client's nameserver address during IPCP negotiations. Set this to `enable' for server override, to `disable' for c… |
| 1.3.6.1.4.1.15.2.5.112 | ScalaranxBootpEnable | read-write | mandatory | This parameter turns on and off the BOOTP relay functionality. This MIB object corresponds to the na/admin parameter 'bootp_enable'. |
| 1.3.6.1.4.1.15.2.5.113 | ScalaranxRoutePref | read-write | mandatory | This parameter determines which routing protocol will take precedence in the routing table. The default value is 'rip'. This MIB object corresponds to the na/a… |
| 1.3.6.1.4.1.15.2.5.114 | ScalaranxRtableSize | read-write | mandatory | This parameter sets the maximun number of different routes (address and mask) allowed in the routing table. The allowable values are: 1 (1024 routes), 2 (2048 … |
| 1.3.6.1.4.1.15.2.5.115 | ScalaranxOppasswd | read-write | mandatory | Setting this parameter changes the Annex's operator level password. Reading this parameter will return either <set> if the password is defined or <unset> if th… |
| 1.3.6.1.4.1.15.2.5.201 | NodeanxOspf | |||
| 1.3.6.1.4.1.15.2.5.201.1 | ScalaranxOspfHolddown | read-write | mandatory | Defines how often OSPF calculates a route (the minimum number of seconds between OSPF runs). Setting this object to 0 results in a default value of 10. This pa… |
| 1.3.6.1.4.1.15.2.5.201.2 | ScalaranxOspfCompat1583 | read-write | mandatory | Dontrols the preference rules used when choosing among multiple AS-external-LSAs advertising the same destination. When enabled, the preference rules remain th… |
| 1.3.6.1.4.1.15.2.5.201.3 | ScalaranxOspfAreaType | read-write | mandatory | This defines the area type. The default value is 'stub'. This parameter corresponds to the na/admin parameter ospf_areatype. |
| 1.3.6.1.4.1.15.2.6.1 | ScalaranxcBoot | read-write | mandatory | The type of boot to be performed. To initiate a dump, this parameter needs to be set by the management station. The values stored in anxcBootImage, anxcBootTim… |
| 1.3.6.1.4.1.15.2.6.2 | ScalaranxcBootImage | read-write | mandatory | The name of the image file to be used with the boot command. |
| 1.3.6.1.4.1.15.2.6.3 | ScalaranxcBootTime | read-write | mandatory | The time at which the next boot is scheduled in either offset +MM or +HH:MM, or a clock time HH:MM format. |
| 1.3.6.1.4.1.15.2.6.4 | ScalaranxcBootMsg | read-write | mandatory | The broadcast message to be displayed when the next boot is performed. |
| 1.3.6.1.4.1.15.2.6.5 | ScalaranxcReset | read-write | mandatory | Writing a value to this object causes the annex to reset the appropriate subsystem. If the value of this object is 'serialports', 'syncports', 'printerports', … |
| 1.3.6.1.4.1.15.2.6.6 | ScalaranxcBcast | read-write | mandatory | Writing a value to this object causes the annex to send the message in anxcBcastMsg to the specified port set. |
| 1.3.6.1.4.1.15.2.6.7 | ScalaranxcBcastMsg | read-write | mandatory | The message to be broadcast to the Annex ports. |
| 1.3.6.1.4.1.15.2.6.8 | ScalaranxcResetSession | read-write | deprecated | This command resets PRI session parameters blocks. The RA6300 will re-read the Session Parameter blocks from config.annex. Existing calls will not be reset. No… |
| 1.3.6.1.4.1.15.2.6.9 | ScalaranxcResetDialout | read-write | mandatory | Reset specific dialout routes using a range string. example: 1,3-5,8 will reset dialout routes 1,3,4,5,8. While 1,3-5,g,8 (g is bogus and anything beyond it wo… |
| 1.3.6.1.4.1.15.2.6.10 | ScalaranxcResetWan1Chan | read-write | mandatory | Resetting a particular channel on WAN 1. |
| 1.3.6.1.4.1.15.2.6.11 | ScalaranxcResetWan2Chan | read-write | mandatory | Resetting a particular channel on WAN 2. |
| 1.3.6.1.4.1.15.2.15.1 | ScalaranxGREInPackets | read-only | mandatory | The total number of GRE packets received. |
| 1.3.6.1.4.1.15.2.15.2 | ScalaranxGREOutPackets | read-only | mandatory | The total number of GRE packets sent. |
| 1.3.6.1.4.1.15.2.15.3 | ScalaranxGREChecksum | read-only | mandatory | The total number of GRE packets received with bad checksum. |
| 1.3.6.1.4.1.15.2.15.4 | ScalaranxGREInDropped | read-only | mandatory | The total number of GRE packets dropped on receive. |
| 1.3.6.1.4.1.15.2.15.5 | ScalaranxGREOutDropped | read-only | mandatory | The total number of GRE packets dropped on transmit. |
| 1.3.6.1.4.1.15.2.15.6 | ScalaranxGREInBytes | read-only | mandatory | The total number of GRE bytes recieved. |
| 1.3.6.1.4.1.15.2.15.7 | ScalaranxGREOutBytes | read-only | mandatory | The total number of GRE bytes transmitted. |
| 1.3.6.1.4.1.15.2.101.1 | ScalaranxChasSegment | read-only | mandatory | The current hub backplane segment to which the module is attached. If this is unknown or not applicable (eg. for a standalone unit), a value of zero is returne… |
| 1.3.6.1.4.1.15.2.101.2 | ScalaranxChasAttChanges | read-only | mandatory | The total number of attachment changes for the module since the last cold/warm start of the module. If this is unknown or not applicable (eg. for a standalone … |
| 1.3.6.1.4.1.15.2.101.3 | ScalaranxChasSlotId | read-only | mandatory | The current slot number for the module in the chassis. If this is unknown or not applicable (eg. for a standalone unit), a value of zero is returned. |
| 1.3.6.1.4.1.15.2.102.1 | ScalaranxModuleLeds | read-only | mandatory | A bit array that contains the current setting of the front panel LED's. The exact format of this information is dependent on the module type and may not be ava… |
| 1.3.6.1.4.1.15.2.102.2 | ScalaranxChasCfgChanges | read-only | mandatory | The total number of configuration changes for the module since the last cold/warm start of the module. |
| 1.3.6.1.4.1.15.2.102.3 | ScalaranxChasSerNum | read-only | mandatory | The serial number of the chassis where the module is installed. If unknown, the value is a zero length string. |
| 1.3.6.1.4.1.15.2.102.4 | ScalaranxChasType | read-only | mandatory | The chassis type where the module is installed. If this information is not available, the value is returned as an OID value '0.0'. |
| 1.3.6.1.4.1.15.2.102.5 | ScalaranxChasVer | read-only | mandatory | The version of the chassis where the module is installed. If this information is not available, a the returned value is a zero length string. |
| 1.3.6.1.4.1.15.2.102.6 | Scalaranx6300LEDs | read-only | mandatory | A bit array that contains the current setting of the front panel LED's. This object is valid for RA6300 platforms only. For ra6300(269) as the 'hwType' the bit… |
| 1.3.6.1.4.1.15.2.102.7 | ScalaranxChasLeds | read-only | mandatory | A bit array that contains the current setting of the front panel LED's. They are displayed in little endian. This object is valid for RA6300, 8000RAC platforms… |
| 1.3.6.1.4.1.15.2.103.1.2 | ScalarenableRadiusAcct | read-write | mandatory | If this object is set to yes(1), radius accounting is enabled Setting this parameter to Y also forces that the accounting server run on the same host as the au… |
| 1.3.6.1.4.1.15.2.103.1.3 | ScalarradiusAuth1Port | read-write | mandatory | This parameter sets the UDP port # that the primary radius server is listening on. The default is port 1645. This MIB object corresponds to the NA/admin parame… |
| 1.3.6.1.4.1.15.2.103.1.4 | ScalarradiusAcct1Port | read-write | mandatory | This parameter sets the UDP port # that the primary radius accounting server is listening on. The default is port 1646. This MIB object corresponds to the NA/a… |
| 1.3.6.1.4.1.15.2.103.1.5 | ScalarradiusSecret | read-write | mandatory | This value contains the radius shared secret for this RAS and the primary Radius server. We recommend this value be at least 16 characters long and should cont… |
| 1.3.6.1.4.1.15.2.103.1.7 | ScalarradiusRetries | read-write | mandatory | This is the number of times to retry the access-request/ accounting request packets before falling over to the secondary host. This parameter cannot be set to … |
| 1.3.6.1.4.1.15.2.103.1.8 | ScalarradiusAcctLevel | read-write | mandatory | This sets the level of radius accounting. Standard restricts the annex to logs of start(1), stop(2), accounting on (7) and accounting off(8). Advanced permits … |
| 1.3.6.1.4.1.15.2.103.1.9 | ScalarradiusPortEncoding | read-write | mandatory | This parameter communicates the NAS port identification to the RADIUS server. The default for this parameter is device. In the default mode the NAS port is enc… |
| 1.3.6.1.4.1.15.2.103.1.10 | ScalarradiusUserPrompt | read-write | mandatory | This parameter defines the prompt string for requesting user name. The prompt string consists of displayable characters and embedded formatting codes. Each for… |
| 1.3.6.1.4.1.15.2.103.1.11 | ScalarradiusPassPrompt | read-write | mandatory | This parameter defines the prompt string for requesting passwords. The prompt string consists of displayable characters and embedded formatting codes. Each for… |
| 1.3.6.1.4.1.15.2.103.1.12 | ScalarradiusPrefAcct1Host | read-write | mandatory | The Internet address of the primary host where the Annex sends its accounting requests. This MIB object corresponds to the NA/admin Annex parameter `radius_acc… |
| 1.3.6.1.4.1.15.2.103.1.13 | ScalarradiusPrefAcct2Host | read-write | mandatory | The Internet address of the radius accounting host where the Annex sends its accounting requests. This MIB object corresponds to the NA/admin parameter `radius… |
| 1.3.6.1.4.1.15.2.103.1.14 | ScalarradiusAcct1Secret | read-write | mandatory | This value contains the shared secret for this RAS and the primary accounting server. We recommend this value be at least 16 characters long and should contain… |
| 1.3.6.1.4.1.15.2.103.1.15 | ScalarradiusAcct2Secret | read-write | mandatory | This value contains the shared secret for this RAS and the secondary accounting server. We recommend this value be at least 16 characters long and should conta… |
| 1.3.6.1.4.1.15.2.103.1.16 | ScalarradiusAuth2Secret | read-write | mandatory | This value contains the shared secret for this RAS and the secondary Radius server. We recommend this value be at least 16 characters long and should contain a… |
| 1.3.6.1.4.1.15.2.103.1.17 | ScalarradiusAuth2Port | read-write | mandatory | This parameter sets the UDP port number that the secondary radius server is listening on. The default is port 1645. This MIB object corresponds to the NA/admin… |
| 1.3.6.1.4.1.15.2.103.1.18 | ScalarradiusAcct2Port | read-write | mandatory | This parameter sets the UDP port # that the secondary radius accounting server is listening on. The default is port 1646. This MIB object corresponds to the NA… |
| 1.3.6.1.4.1.15.2.103.1.19 | ScalarradiusCompatibility | read-write | mandatory | Values of this object can either be set to BayNetworks or USR to indicate how to handle RADIUS attributes. Change of this parameter will not be effective, even… |
| 1.3.6.1.4.1.15.2.103.1.20 | ScalarradiusAuthTimeout | read-write | mandatory | This is the maximum time to wait for a packet to be received from the radius authentication servers. This value is in seconds. The default value is 4secs. This… |
| 1.3.6.1.4.1.15.2.103.1.21 | ScalarradiusAcctTimeout | read-write | mandatory | This value is used in determining the maximum time to wait for the packet (from radius accounting servers) and is multiplied by the tries for the total wait ti… |
| 1.3.6.1.4.1.15.2.103.1.22 | ScalarradiusAcctDestination | read-write | mandatory | If this object is set to acctserver(1), radius accounting is sent to the accounting server only. Setting it to both(2) causes accounting to be sent to the auth… |
| 1.3.6.1.4.1.15.2.103.2.1 | ScalarradiusClientInvalidServerAddresses | read-only | deprecated | The total number of RADIUS Access-Response messages received from unknown addresses since client start-up |
| 1.3.6.1.4.1.15.2.103.2.2 | ScalarradiusClientIdentifier | read-only | deprecated | The NAS-Identifier of the RADIUS client. |
| 1.3.6.1.4.1.15.2.103.2.3 | TableradiusServerTable | not-accessible | deprecated | The (conceptual) table listing the RADIUS servers with which the client shares a secret. |
| 1.3.6.1.4.1.15.2.103.2.3.1 | RowradiusServerEntry | not-accessible | deprecated | An entry (conceptual row) representing a RADIUS server with which the client shares a secret. |
| 1.3.6.1.4.1.15.2.103.2.3.1.1 | ColumnradiusServerIndex | read-only | deprecated | The RADIUS server with which the client interacts |
| 1.3.6.1.4.1.15.2.103.2.3.1.2 | ColumnradiusServerAddress | read-only | deprecated | The IP address of the RADIUS server referred to in this table entry |
| 1.3.6.1.4.1.15.2.103.2.3.1.3 | ColumnradiusClientRoundTripTime | read-only | deprecated | The total roundtrip time of the last packet sent between the client and the RADIUS server referred to in this table entry |
| 1.3.6.1.4.1.15.2.103.2.3.1.4 | ColumnradiusClientAccessRequests | read-only | deprecated | The total number of RADIUS Access-Request messages sent since client start-up |
| 1.3.6.1.4.1.15.2.103.2.3.1.5 | ColumnradiusClientAccessRetransmissions | read-only | deprecated | The total number of RADIUS Access-Request messages retransmitted since client start-up |
| 1.3.6.1.4.1.15.2.103.2.3.1.6 | ColumnradiusClientAccessAccepts | read-only | deprecated | The total number of RADIUS Access-Accept messages received since client start-up |
| 1.3.6.1.4.1.15.2.103.2.3.1.7 | ColumnradiusClientAccessRejects | read-only | deprecated | The total number of RADIUS Access-Reject messages received since client start-up |
| 1.3.6.1.4.1.15.2.103.2.3.1.8 | ColumnradiusClientAccessChallenges | read-only | deprecated | The total number of RADIUS Access-Challenge messages received since client start-up |
| 1.3.6.1.4.1.15.2.103.2.3.1.9 | ColumnradiusClientMalformedAccessResponses | read-only | deprecated | The total number of malformed RADIUS Access-Response messages received since client start-up |
| 1.3.6.1.4.1.15.2.103.2.3.1.10 | ColumnradiusClientAuthenticationBadAuthenticators | read-only | deprecated | The total number of RADIUS Access-Response messages containing invalid authenticators received since client start-up |
| 1.3.6.1.4.1.15.2.103.2.3.1.11 | ColumnradiusClientAuthenticationPendingRequests | read-only | deprecated | The total number of RADIUS Access-Request messages that have not yet timed out or received a response |
| 1.3.6.1.4.1.15.2.103.2.3.1.12 | ColumnradiusClientAuthenticationTimeouts | read-only | deprecated | The total number of authentication timeouts since client startup |
| 1.3.6.1.4.1.15.2.103.2.3.1.13 | ColumnradiusClientAccountingRequests | read-only | deprecated | The total number of RADIUS Accounting-Request messages sent since client start-up |
| 1.3.6.1.4.1.15.2.103.2.3.1.14 | ColumnradiusClientAccountingRetransmissions | read-only | deprecated | The total number of RADIUS Accounting-Request messages retransmitted since client start-up |
| 1.3.6.1.4.1.15.2.103.2.3.1.15 | ColumnradiusClientAccountingResponses | read-only | deprecated | The total number of RADIUS Accounting-Response messages received since client start-up |
| 1.3.6.1.4.1.15.2.103.2.3.1.16 | ColumnradiusClientMalformedAccountingResponses | read-only | deprecated | The total number of malformed RADIUS Accounting-Response messages received since client start-up |
| 1.3.6.1.4.1.15.2.103.2.3.1.17 | ColumnradiusClientAccountingBadAuthenticators | read-only | deprecated | The total number of RADIUS Accounting-Response messages which contained invalid authenticators received since client start-up |
| 1.3.6.1.4.1.15.2.103.2.3.1.18 | ColumnradiusClientAccountingPendingRequests | read-only | deprecated | The total number of RADIUS Accounting-Request messages that have not yet timed out or received a response |
| 1.3.6.1.4.1.15.2.103.2.3.1.19 | ColumnradiusClientAccountingTimeouts | read-only | deprecated | The total number of accounting timeouts since client startup |
| 1.3.6.1.4.1.15.2.103.2.3.1.20 | ColumnradiusClientUnknownType | read-only | deprecated | The total number of RADIUS messages of unknown type which were received since client start-up |
| 1.3.6.1.4.1.15.2.104.1 | ScalargsyTotalPorts | read-only | mandatory | The number of GSY ports on this Annex. |
| 1.3.6.1.4.1.15.2.104.2 | ScalargsyTotalInChars | read-only | mandatory | The total number of characters received on all GSY ports. |
| 1.3.6.1.4.1.15.2.104.3 | ScalargsyTotalOutChars | read-only | mandatory | The total number of characters transmitted on all gsy ports. |
| 1.3.6.1.4.1.15.2.104.4 | ScalargsyTotalFrameCheckErrs | read-only | mandatory | The total number of frame check errors detected on all gsy ports since the last boot. |
| 1.3.6.1.4.1.15.2.104.5 | ScalargsyTotalXmitUnderrunErrs | read-only | mandatory | The total number of transmit underrun errors detected on all gsy ports since the last boot. |
| 1.3.6.1.4.1.15.2.104.6 | ScalargsyTotalRecvOverrunErrs | read-only | mandatory | The total number of receive overrun errors detected on all gsy ports since the last boot. |
| 1.3.6.1.4.1.15.2.104.7 | ScalargsyInterfaceType | read-only | mandatory | The interface running on this gsy |
| 1.3.6.1.4.1.15.2.105.1 | ScalaranxPktsComp | read-only | mandatory | This is the total number of packets that are successfully compressed by the compression card. |
| 1.3.6.1.4.1.15.2.105.2 | ScalaranxPktsDecomp | read-only | mandatory | This is the total number of packets that are successfully decompressed by the compression card. |
| 1.3.6.1.4.1.15.2.105.3 | ScalaranxUncompPkts | read-only | mandatory | This is the total number of packets that are received by CCP and are marked as being uncompressed packets (valid for MPPC). |
| 1.3.6.1.4.1.15.2.105.4 | ScalaranxPktsCompFails | read-only | mandatory | Number of packets that failed to be compress due to data expansion or lack or resources. |
| 1.3.6.1.4.1.15.2.105.5 | ScalaranxPktsDataExpansion | read-only | mandatory | Number of packets that failed to be compress due to data expansion. |
| 1.3.6.1.4.1.15.2.105.6 | ScalaranxPktsDecompFails | read-only | mandatory | Number of packets that failed to decompress due to checksum errors, out of sequence errors or lack or resources. |
| 1.3.6.1.4.1.15.2.105.7 | ScalaranxLCBCRCMismatches | read-only | mandatory | This is the total number of packets that failed to decompress due to LCB/CRC checksum mismatch or out of sequence errors. |
| 1.3.6.1.4.1.15.2.105.8 | ScalaranxCompResets | read-only | mandatory | This is the total number of explicit compressor resets. |
| 1.3.6.1.4.1.15.2.105.9 | ScalaranxDecompResets | read-only | mandatory | This is the total number of explicit decompressor resets. |
| 1.3.6.1.4.1.15.2.105.10 | ScalaranxHistoryFails | read-only | mandatory | This is the total number of times we failed to allocate a history in the compression card CRAM memory for a session. |
| 1.3.6.1.4.1.15.2.105.11 | ScalaranxPktsDropFullQ | read-only | mandatory | This is the total number of packets that got dropped because the hardware compression / decompression queue was full. |
| 1.3.6.1.4.1.15.2.105.12 | ScalaranxCompMbufFails | read-only | mandatory | This is the total number of packets that failed to compress / decompress because of a lack of mbufs. |
| 1.3.6.1.4.1.15.2.105.13 | ScalaranxCompBefore | read-only | mandatory | This is total number of bytes before compression. |
| 1.3.6.1.4.1.15.2.105.14 | ScalaranxCompAfter | read-only | mandatory | This is total number of bytes after compression. |
| 1.3.6.1.4.1.15.2.105.15 | ScalaranxDecompBefore | read-only | mandatory | This is total number of bytes before decompression. |
| 1.3.6.1.4.1.15.2.105.16 | ScalaranxDecompAfter | read-only | mandatory | This is total number of bytes after decompression. |
| 1.3.6.1.4.1.207.8.4.4.4.139.1 | Nodeigmpconfig | |||
| 1.3.6.1.4.1.207.8.4.4.4.139.1.1 | ScalarigmpVersion | read-write | mandatory | Controls if IGMP is enabled, and if enabled which version of the IGMP protocol to use. The default is IGMP protocol version 2. This MIB object corresponds to t… |
| 1.3.6.1.4.1.207.8.4.4.4.139.1.2 | ScalarigmpRobustness | read-write | mandatory | Robustness allows tuning for a lossy subnet. If lossy subnets exist, then this value should be increased. Valid values are in the range of 1-15. The default of… |
| 1.3.6.1.4.1.207.8.4.4.4.139.1.3 | ScalarigmpQueryTime | read-write | mandatory | This is the Max Response Time inserted into general query messages. Valid values are in the range of 1-65535 deciseconds. The default is 100 deciseconds. This … |
| 1.3.6.1.4.1.207.8.4.4.4.139.1.4 | ScalarigmpResponseTime | read-write | mandatory | This is the Query Response time(Interval). When periodic general queries are made this value is placed into the Max Response Time field of the message. Settabl… |
| 1.3.6.1.4.1.207.8.4.4.4.139.1.5 | ScalarigmpStartQueryTime | read-write | mandatory | This is the Startup Query Interval. It specifies the time interval between queries sent out on startup. Settable values for are in the decisecond range of 1-65… |
| 1.3.6.1.4.1.207.8.4.4.4.139.1.6 | ScalarigmpStartQueryCount | read-write | mandatory | This is the Startup Query Count. It specifies the number of queries sent out on startup. Valid values for are in the range of 1-15. This MIB object corresponds… |
| 1.3.6.1.4.1.207.8.4.4.4.139.1.7 | ScalarigmpLastQueryTime | read-write | mandatory | The Last Member Query time(Interval) is the Max Response Time inserted into group-specific queries sent in response to leave group messages. It also the amount… |
| 1.3.6.1.4.1.207.8.4.4.4.139.1.8 | ScalarigmpLastQueryCount | read-write | mandatory | The Last Member Query Count is the number of group specific queries sent before the router assumes there are no local members. The default is 2. This MIB objec… |
| 1.3.6.1.4.1.207.8.4.4.4.139.1.9 | ScalarigmpJoinQueryTime | read-write | mandatory | This specifies the time interval between repetitions of Unsolicited Reports when a host initially become a member of a group. Valid values are in the range of … |
| 1.3.6.1.4.1.207.8.4.4.4.139.1.10 | ScalarigmpV1Timeout | read-write | mandatory | This is the Version 1 Router Present Timeout. It controls how long a host must wait before after hearing a Version 1 Query before it may send any IGMP version … |
| 1.3.6.1.4.1.207.8.4.4.4.139.1.11 | ScalarigmpQueueSize | read-write | mandatory | The maximum number of elements that can be allocated to the IGMP processing queue. The value will be rounded up to the next value evenly divisible by 10. This … |
| 1.3.6.1.4.1.207.8.4.4.4.139.1.12 | ScalarigmpMaxPendingMcast | read-write | mandatory | The maximum number of multicast messages that can be placed in the IGMP processing queue. We recommend that this value be less than igmpQueueSize otherwise une… |
| 1.3.6.1.4.1.272.4.23.8.2 | Nodel2tpStats | |||
| 1.3.6.1.4.1.272.4.23.8.2.1 | Scalaranxl2tpCntrlPkts | read-only | mandatory | The total control pkts transmitted. |
| 1.3.6.1.4.1.272.4.23.8.2.2 | Scalaranxl2tpDataPkts | read-only | mandatory | The total data packets transmitted. |
| 1.3.6.1.4.1.272.4.23.8.2.3 | Scalaranxl2tpCntrlPktsRx | read-only | mandatory | The total control pkts rx |
| 1.3.6.1.4.1.272.4.23.8.2.4 | Scalaranxl2tpDataPktsRx | read-only | mandatory | The total data packets rx. |
| 1.3.6.1.4.1.272.4.23.8.2.5 | Scalaranxl2tpSeqErr | read-only | mandatory | The total pkts drop on rx for bad seq |
| 1.3.6.1.4.1.272.4.23.8.2.6 | Scalaranxl2tpPppDownErr | read-only | mandatory | The total data pkts drop on rx - to ppp not ready . |
| 1.3.6.1.4.1.272.4.23.8.2.7 | Scalaranxl2tpProtocolErr | read-only | mandatory | The total pkts with a protocol error. |
| 1.3.6.1.4.1.272.4.23.8.2.8 | Scalaranxl2tpStateErr | read-only | mandatory | The total pkts drop - tunnel/session state error. |
| 1.3.6.1.4.1.272.4.23.8.2.9 | Scalaranxl2tpPktsDrop | read-only | mandatory | The total pkts dropped on rx for other reasons. |