ZTE-AN-EQUIP-MIB
485 objects
This MIB defines zte Access Node managed objects.
Imported Objects
| SNMPv2-SMI | Counter64 Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DateAndTime DisplayString RowStatus TruthValue |
| ZTE-AN-TC-MIB | zxAn |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.3902.1015.2 | IdentityzxAnEquipMib | This MIB defines zte Access Node managed objects. | ||
| 1.3.6.1.4.1.3902.1015.2.1 | NodezxAnEquipObjects | |||
| 1.3.6.1.4.1.3902.1015.2.1.1 | NodezxAnChassisMgmt | |||
| 1.3.6.1.4.1.3902.1015.2.1.1.1 | TablezxAnRackTable | not-accessible | current | This table includes the enable or disable plug and play of the rack. |
| 1.3.6.1.4.1.3902.1015.2.1.1.1.1 | RowzxAnRackEntry | not-accessible | current | An entry in zxAnRackTable. |
| 1.3.6.1.4.1.3902.1015.2.1.1.1.1.1 | ColumnzxAnRackNo | not-accessible | current | |
| 1.3.6.1.4.1.3902.1015.2.1.1.1.1.2 | ColumnzxAnRackActType | read-only | current | This MIB is defined for actual rack type. |
| 1.3.6.1.4.1.3902.1015.2.1.1.1.1.3 | ColumnzxAnRackCfgType | read-create | current | This MIB is defined for configged rack type. |
| 1.3.6.1.4.1.3902.1015.2.1.1.1.1.4 | ColumnzxAnRackInvSn | read-create | current | This MIB is defined for serial number of this rack. it is used by inventroy management. |
| 1.3.6.1.4.1.3902.1015.2.1.1.1.1.5 | ColumnzxAnRackRowStatus | read-create | current | The row status of this entry. |
| 1.3.6.1.4.1.3902.1015.2.1.1.2 | TablezxAnShelfTable | not-accessible | current | This table includes the enable or disable plug and play of the shelf. |
| 1.3.6.1.4.1.3902.1015.2.1.1.2.1 | RowzxAnShelfEntry | not-accessible | current | An entry in zxAnShelfTable. |
| 1.3.6.1.4.1.3902.1015.2.1.1.2.1.1 | ColumnzxAnShelfNo | not-accessible | current | |
| 1.3.6.1.4.1.3902.1015.2.1.1.2.1.2 | ColumnzxAnShelfHardVersion | read-only | current | This MIB is defined for the hard driver on the shelf. |
| 1.3.6.1.4.1.3902.1015.2.1.1.2.1.3 | ColumnzxAnShelfActType | read-only | current | |
| 1.3.6.1.4.1.3902.1015.2.1.1.2.1.4 | ColumnzxAnShelfCfgType | read-create | current | |
| 1.3.6.1.4.1.3902.1015.2.1.1.2.1.5 | ColumnzxAnShelfInvSn | read-create | current | This MIB is defined for serial number of this shelf. it is used by inventroy management. |
| 1.3.6.1.4.1.3902.1015.2.1.1.2.1.6 | ColumnzxAnShelfCleiCode | read-only | current | This MIB is defined for CLEI code of this Shelf. it is used by inventroy management.Pls reference http://www.commonlanguage.com to get knowledge about CLEI cod… |
| 1.3.6.1.4.1.3902.1015.2.1.1.2.1.7 | ColumnzxAnLogicShelfNo | read-create | current | This MIB is defined for logic Shelf No |
| 1.3.6.1.4.1.3902.1015.2.1.1.2.1.8 | ColumnzxAnShelfHardwareType | read-only | current | The hardware type of the shelf. |
| 1.3.6.1.4.1.3902.1015.2.1.1.2.1.9 | ColumnzxAnShelfAlias | read-create | current | This object is an 'alias' name for the shelf, as specified by a network manager, and provides a non-volatile 'handle' for the shelf. |
| 1.3.6.1.4.1.3902.1015.2.1.1.2.1.10 | ColumnzxAnShelfAdminStatus | read-create | current | This MIB is defined for rebooting shelf. |
| 1.3.6.1.4.1.3902.1015.2.1.1.2.1.15 | ColumnzxAnShelfRowStatus | read-create | current | The row status of this entry. |
| 1.3.6.1.4.1.3902.1015.2.1.1.3 | TablezxAnCardTable | not-accessible | current | This table includes the enable or disable plug and play of the Card. |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1 | RowzxAnCardEntry | not-accessible | current | An entry in zxAnCardTable. |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1.1 | ColumnzxAnSlotNo | not-accessible | current | |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1.2 | ColumnzxAnCardConfMainType | read-create | current | This MIB is defined for the main card type to config on the slot. Main card type indicates the category of hardware,such as 64-ports adsl card,4-ports ethernet… |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1.3 | ColumnzxAnCardActMainType | read-only | current | This MIB is defined for the actually main card type on the slot. |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1.4 | ColumnzxAnCardActType | read-only | current | This MIB is defined for the actually card type on the slot. Card type indicates the type of detailed hardware,such as ATUGA and ATUGB, they'er all 32-ports Ads… |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1.5 | ColumnzxAnCardOperStatus | read-only | current | This MIB is defined for the sub card status on the card. inService(1) provided normally. notInService(2) hwOnline(3) hwOffline(4) configuring(5) configFailed(6… |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1.6 | ColumnzxAnCardAdminStatus | read-create | current | This MIB is defined for the card admin status on the card. For example:reset(1),switch(2) reset(1) switch(2) stopService(3) active(4) deactive(5) service force… |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1.7 | ColumnzxAnCardPortNums | read-only | current | The numbers of physical port which contained in this board. If the board has no this attribute,it should be 0. |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1.8 | ColumnzxAnCardActivePortNums | read-only | current | The numbers of actived physical port which contained in this board. If the board has no this attribute,it should be 0. |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1.9 | ColumnzxAnCardCpuLoad | read-only | current | The current CPU load of this board.If this board has more than one CPU,the average value is allowed. If the board has no this attribute,it should be 0. |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1.10 | ColumnzxAnCardCpuLoadThreshold | read-create | current | The CPU load threshold of this board.When zxAnCardCpuLoad is higher than zxAnCardCpuLoadThreshold,zxAnEquipCardCpuLoadAlarm trap should be generated by agent. |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1.11 | ColumnzxAnCardMemUsage | read-only | current | The current memory usage of this board. If the board has no this attribute,it should be 0. |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1.12 | ColumnzxAnCardMemUsageThreshold | read-create | current | The memory usage threshold of this board.When zxAnCardMemUsage is higher than zxAnCardMemUsageThreshold,zxAnEquipCardMemoryOverLoad trap should be generated by… |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1.13 | ColumnzxAnCardStandbyStatus | read-only | current | This MIB is defined for the card operation status on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1.14 | ColumnzxAnCardInvSn | read-create | current | This MIB is defined for serial number of this card. it is used by inventroy management. |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1.15 | ColumnzxAnCardCleiCode | read-only | current | This MIB is defined for CLEI code of this card. it is used by inventroy management.Pls reference http://www.commonlanguage.com to get knowledge about CLEI code. |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1.16 | ColumnzxAnCardAccessoriesType | read-only | current | This MIB is defined for accessories type of this card, such as splitter of DSLAM,the value of this variable should be the type of hardware, eg. PNVTA,PNVNP,PNV… |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1.17 | ColumnzxAnCardAccessoriesOperstatus | read-only | current | This MIB is defined for operational status of the card accessories. |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1.18 | ColumnzxAnCardLockStatus | read-create | current | This MIB is defined for lock status of the card |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1.19 | ColumnzxAnCardMemSize | read-only | current | The current memory size of this board. If the board has no this attribute,it should be 0. |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1.20 | ColumnzxAnCardCpldUpdateStatus | read-create | current | This MIB is defined for CPLD update status of the card |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1.21 | ColumnzxAnCardAvailableStorageSize | read-only | current | The available storage space size in this card. |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1.22 | ColumnzxAnCardTotalStorageSize | read-only | current | The total storage space size in this card. |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1.24 | ColumnzxAnCardEnergySavingEnable | read-create | current | This object indicates that the Saving Energy mode of the card, Specifically, it is set to true if the local system wishes to use Saving Energy mode or falseif … |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1.25 | ColumnzxAnCardAlias | read-create | current | This object is an 'alias' name for the card, as specified by a network manager, and provides a non-volatile 'handle' for the card. |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1.26 | ColumnzxAnCardLastStartupTime | read-only | current | This MIB is defined for last startup time of the card. |
| 1.3.6.1.4.1.3902.1015.2.1.1.3.1.30 | ColumnzxAnCardRowStatus | read-create | current | The row status of this entry. |
| 1.3.6.1.4.1.3902.1015.2.1.1.4 | TablezxAnSubcardTable | not-accessible | current | This table includes the enable or disable plug and play of the subcard. |
| 1.3.6.1.4.1.3902.1015.2.1.1.4.1 | RowzxAnSubcardEntry | not-accessible | current | An entry in zxAnSubcardTable. |
| 1.3.6.1.4.1.3902.1015.2.1.1.4.1.1 | ColumnzxAnSubcardNo | not-accessible | current | |
| 1.3.6.1.4.1.3902.1015.2.1.1.4.1.2 | ColumnzxAnSubCardCfgMainType | read-create | current | This MIB is defined for the main subcard type to config on the slot. Main subcard type indicates the category of hardware,such as 4-ports ethernet subcard. |
| 1.3.6.1.4.1.3902.1015.2.1.1.4.1.3 | ColumnzxAnSubCardActMainType | read-only | current | This MIB is defined for the actually main subcard type on the slot. |
| 1.3.6.1.4.1.3902.1015.2.1.1.4.1.4 | ColumnzxAnSubCardActType | read-only | current | This MIB is defined for the actually subcard type on the slot. It indicates the type of detailed hardware. NOTE: The value of this variable MUST abide by ZTE'S… |
| 1.3.6.1.4.1.3902.1015.2.1.1.4.1.5 | ColumnzxAnSubcardOperStatus | read-only | current | This MIB is defined for the sub card status on the card. inService(1) provided normally. notInService(2) hwOffline(3) hwOnline(3) configuring(5) configFailed(6… |
| 1.3.6.1.4.1.3902.1015.2.1.1.4.1.6 | ColumnzxAnSubcardAdminStatus | read-create | current | This MIB is defined for the card admin status on the card. For example:reset(1),switch(2) reset(1) switch(2) stopService(3) active(4) deactive(5) service force… |
| 1.3.6.1.4.1.3902.1015.2.1.1.4.1.7 | ColumnzxAnSubcardPortNums | read-only | current | The numbers of physical port which contained in this board. If the board has no this attribute,it should be 0. |
| 1.3.6.1.4.1.3902.1015.2.1.1.4.1.8 | ColumnzxAnSubcardActivePortNums | read-only | current | The numbers of actived physical port which contained in this board. If the board has no this attribute,it should be 0. |
| 1.3.6.1.4.1.3902.1015.2.1.1.4.1.9 | ColumnzxAnSubcardCpuLoad | read-only | current | The current CPU load of this board.If this board has more than one CPU,the average value is allowed. If the board has no this attribute,it should be 0. |
| 1.3.6.1.4.1.3902.1015.2.1.1.4.1.10 | ColumnzxAnSubcardMemUsage | read-only | current | The current memory usage of this board. If the board has no this attribute,it should be 0. |
| 1.3.6.1.4.1.3902.1015.2.1.1.4.1.11 | ColumnzxAnSubcardInvSn | read-create | current | This MIB is defined for serial number of this subcard. it is used by inventroy management. |
| 1.3.6.1.4.1.3902.1015.2.1.1.4.1.12 | ColumnzxAnSubcardCleiCode | read-only | current | This MIB is defined for CLEI code of this card. it is used by inventroy management.Pls reference http://www.commonlanguage.com to get knowledge about CLEI code. |
| 1.3.6.1.4.1.3902.1015.2.1.1.4.1.13 | ColumnzxAnSubcardMemSize | read-only | current | The current memory size of this sub card. If the board has no this attribute,it should be 0. |
| 1.3.6.1.4.1.3902.1015.2.1.1.4.1.14 | ColumnzxAnSubcardCpldUpdateStatus | read-create | current | This MIB is defined for CPLD update status of the subcard |
| 1.3.6.1.4.1.3902.1015.2.1.1.4.1.20 | ColumnzxAnSubcardRowStatus | read-create | current | The row status of this entry. |
| 1.3.6.1.4.1.3902.1015.2.1.1.5 | NodezxAnPhyConfMgmt | |||
| 1.3.6.1.4.1.3902.1015.2.1.1.5.2 | TablezxAnStandbyEnableTable | not-accessible | current | This table includes the shelf standy function information. |
| 1.3.6.1.4.1.3902.1015.2.1.1.5.2.1 | RowzxAnStandbyEnableEntry | not-accessible | current | An entry in zxAnStandbyEnable. |
| 1.3.6.1.4.1.3902.1015.2.1.1.5.2.1.1 | ColumnzxStandbyEnable | read-write | current | config ne standby control card offline alarm. when standby card offline ,a alarm will raise if this function is enabled |
| 1.3.6.1.4.1.3902.1015.2.1.1.5.5 | ScalarzxAnChassisPnpMode | read-write | current | config Ne card PNP mode,PNP mode means when card on shelf,then this card can use without add it |
| 1.3.6.1.4.1.3902.1015.2.1.1.6 | TablezxAnPowerSupplyCardTable | not-accessible | current | Power supply card table. |
| 1.3.6.1.4.1.3902.1015.2.1.1.6.1 | RowzxAnPowerSupplyCardEntry | not-accessible | current | Power supply card entry. |
| 1.3.6.1.4.1.3902.1015.2.1.1.6.1.1 | ColumnzxAnPowerSupplyCardPreviousType | accessible-for-notify | current | This object is the power supply card type on the slot before hardware fault happened. Only used for C300M. |
| 1.3.6.1.4.1.3902.1015.2.1.1.6.1.2 | ColumnzxAnPowerSupplyCardCurrentType | accessible-for-notify | current | This object is the power supply card type on the slot after hardware fault happened. Only used for C300M. |
| 1.3.6.1.4.1.3902.1015.2.1.2 | NodezxAnVerMgmt | |||
| 1.3.6.1.4.1.3902.1015.2.1.2.1 | NodezxAnVerFtpMgmt | |||
| 1.3.6.1.4.1.3902.1015.2.1.2.1.1 | ScalarzxAnFtpVerFileType | read-write | current | The ftp client function is used to implement the transmission of version between an agent and a manager. |
| 1.3.6.1.4.1.3902.1015.2.1.2.1.2 | ScalarzxAnFtpVerClntOperType | read-write | current | The operation type is based on ManagedMainType and ManagedSubType. for example: OPERATION TYPE(value) upload(1) downLoad(2) update_bootrom(3) update_version(4)… |
| 1.3.6.1.4.1.3902.1015.2.1.2.1.3 | ScalarzxAnFtpVerServerIpAddress | read-write | current | The IP Address for the FTP server used for downloading and/or uploading files. |
| 1.3.6.1.4.1.3902.1015.2.1.2.1.4 | ScalarzxAnFtpVerServerUserName | read-write | current | The FTP username. |
| 1.3.6.1.4.1.3902.1015.2.1.2.1.5 | ScalarzxAnFtpVerServerUserPwd | read-write | current | The FTP User Password. |
| 1.3.6.1.4.1.3902.1015.2.1.2.1.6 | ScalarzxAnFtpVerServerFilePath | read-write | current | The FTP File Path, start from the root directory. |
| 1.3.6.1.4.1.3902.1015.2.1.2.1.7 | ScalarzxAnFtpVerServerFileName | read-write | current | The FTP file name. |
| 1.3.6.1.4.1.3902.1015.2.1.2.1.8 | ScalarzxAnFtpVerClntAdminStatus | read-write | current | Ftp administrative status. |
| 1.3.6.1.4.1.3902.1015.2.1.2.1.9 | ScalarzxAnFtpVerClntOperStatus | read-only | current | Ftp operational status. |
| 1.3.6.1.4.1.3902.1015.2.1.2.1.10 | ScalarzxAnFtpVerClntFailedReason | read-only | current | Ftp failed reason. |
| 1.3.6.1.4.1.3902.1015.2.1.2.1.11 | ScalarzxAnSwManualUpdateShelf | read-write | current | The Shelf No. is used for updating version file from MP to NP. |
| 1.3.6.1.4.1.3902.1015.2.1.2.1.12 | ScalarzxAnSwManualUpdateSlotList | read-write | current | The slot No. is used for updating version file from MP to NP.They can be update in batch. for example:1,2,3 |
| 1.3.6.1.4.1.3902.1015.2.1.2.1.13 | ScalarzxAnSwManualUpdateCardType | read-write | current | The card type is used for updating version file from MP to NP. |
| 1.3.6.1.4.1.3902.1015.2.1.2.1.14 | ScalarzxAnFtpVerUpdateFileLocation | read-write | current | The update flag is used for indicating the version file location when updating version or bootrom file in NP. It include two locations:one is from local flash(… |
| 1.3.6.1.4.1.3902.1015.2.1.2.1.15 | ScalarzxAnFtpVerClntProgress | read-only | current | The total progress of upload or download version ,including master and slave card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.1.16 | ScalarzxAnFtpVerFileSize | read-write | current | The file size of download. |
| 1.3.6.1.4.1.3902.1015.2.1.2.1.17 | ScalarzxAnFtpAdminType | read-only | current | This MIB is defined for FTP administer type,1 indicate version and 2 indicate batch. |
| 1.3.6.1.4.1.3902.1015.2.1.2.1.18 | ScalarzxAnFtpProtocolType | read-write | current | The flag is used for indicating the ftp protocol when downing versions between EMS and NE . It include two protocols:one is ftp and another is sftp. |
| 1.3.6.1.4.1.3902.1015.2.1.2.2 | TablezxAnCardVersionTable | not-accessible | current | This table includes the Card version information. |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1 | RowzxAnCardVersionEntry | not-accessible | current | An entry in zxAnCardTable. |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1.1 | ColumnzxAnSwCardHardwareVersion | read-only | current | This MIB is defined for the hard driver on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1.2 | ColumnzxAnSwCardFileName | read-only | current | This MIB is defined for the version file name on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1.3 | ColumnzxAnSwCardFileType | read-only | current | This MIB is defined for the version file type on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1.4 | ColumnzxAnSwCardVersion | read-only | current | This MIB is defined for the version tag on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1.5 | ColumnzxAnSwCardFileLen | read-only | current | This MIB is defined for the version file length on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1.6 | ColumnzxAnSwCardBuildTime | read-only | current | This MIB defines version build time.for example: yyyy-mm-dd HH:MM:SS.(2001-01-01 02:22:33). |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1.7 | ColumnzxAnSwCardBootwareFileName | read-only | current | This MIB is defined for the Bootrom file name on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1.8 | ColumnzxAnSwCardBootwareFileType | read-only | current | This MIB is defined for the Bootrom file type on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1.9 | ColumnzxAnSwCardBootwareVersion | read-only | current | This MIB is defined for the Bootrom tag on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1.10 | ColumnzxAnSwCardBootwareFileLen | read-only | current | This MIB is defined for the Bootrom file length on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1.11 | ColumnzxAnSwCardBootwareBuildTime | read-only | current | This MIB defines version build time.for example: yyyy-mm-dd HH:MM:SS.(2001-01-01 02:22:33). |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1.12 | ColumnzxAnSwCardFirmware1FileName | read-only | current | This MIB is defined for the Firmware file name on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1.13 | ColumnzxAnSwCardFirmware1FileType | read-only | current | This MIB is defined for the Firmware file type on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1.14 | ColumnzxAnSwCardFirmware1Version | read-only | current | This MIB is defined for the Firmware tag on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1.15 | ColumnzxAnSwCardFirmware1FileLen | read-only | current | This MIB is defined for the Firmware file length on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1.16 | ColumnzxAnSwCardFirmware1BuildTime | read-only | current | This MIB defines version build time.for example: yyyy-mm-dd HH:MM:SS.(2001-01-01 02:22:33). |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1.17 | ColumnzxAnSwCardFirmware2FileName | read-only | current | This MIB is defined for the Firmware file name on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1.18 | ColumnzxAnSwCardFirmware2FileType | read-only | current | This MIB is defined for the Firmware file type on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1.19 | ColumnzxAnSwCardFirmware2Version | read-only | current | This MIB is defined for the Firmware tag on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1.20 | ColumnzxAnSwCardFirmware2FileLen | read-only | current | This MIB is defined for the Firmware file length on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1.21 | ColumnzxAnSwCardFirmware2BuildTime | read-only | current | This MIB defines version build time.for example: yyyy-mm-dd HH:MM:SS.(2001-01-01 02:22:33). |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1.22 | ColumnzxAnSwCardFirmware3FileName | read-only | current | This MIB is defined for the Firmware file name on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1.23 | ColumnzxAnSwCardFirmware3FileType | read-only | current | This MIB is defined for the Firmware file type on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1.24 | ColumnzxAnSwCardFirmware3Version | read-only | current | This MIB is defined for the Firmware tag on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1.25 | ColumnzxAnSwCardFirmware3FileLen | read-only | current | This MIB is defined for the Firmware file length on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.2.1.26 | ColumnzxAnSwCardFirmware3BuildTime | read-only | current | This MIB defines version build time.for example: yyyy-mm-dd HH:MM:SS.(2001-01-01 02:22:33). |
| 1.3.6.1.4.1.3902.1015.2.1.2.3 | TablezxAnSubcardVersionTable | not-accessible | current | This table includes the sub card version information. |
| 1.3.6.1.4.1.3902.1015.2.1.2.3.1 | RowzxAnSubcardVersionEntry | not-accessible | current | An entry in zxAnSubcardVersionTable. |
| 1.3.6.1.4.1.3902.1015.2.1.2.3.1.1 | ColumnzxAnSwSubcardHardwareVersion | read-only | current | This MIB is defined for the hard driver on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.3.1.2 | ColumnzxAnSwSubcardFileName | read-only | current | This MIB is defined for the version file name on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.3.1.3 | ColumnzxAnSwSubcardFileType | read-only | current | This MIB is defined for the version file type on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.3.1.4 | ColumnzxAnSwSubcardVersion | read-only | current | This MIB is defined for the version tag on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.3.1.5 | ColumnzxAnSwSubcardFileLen | read-only | current | This MIB is defined for the version file length on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.3.1.6 | ColumnzxAnSwSubcardBuildTime | read-only | current | This MIB defines version build time.for example: yyyy-mm-dd HH:MM:SS.(2001-01-01 02:22:33). |
| 1.3.6.1.4.1.3902.1015.2.1.2.3.1.7 | ColumnzxAnSwSubcardBootwareFileName | read-only | current | This MIB is defined for the Bootrom file name on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.3.1.8 | ColumnzxAnSwSubcardBootwareFileType | read-only | current | This MIB is defined for the Bootrom file type on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.3.1.9 | ColumnzxAnSwSubcardBootwareVersion | read-only | current | This MIB is defined for the Bootrom tag on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.3.1.10 | ColumnzxAnSwSubcardBootwareFileLen | read-only | current | This MIB is defined for the Bootrom file length on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.3.1.11 | ColumnzxAnSwSubcardBootwareBuildTime | read-only | current | This MIB defines version build time.for example: yyyy-mm-dd HH:MM:SS.(2001-01-01 02:22:33). |
| 1.3.6.1.4.1.3902.1015.2.1.2.3.1.12 | ColumnzxAnSwSubcardFirmwareFileName | read-only | current | This MIB is defined for the Firmware file name on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.3.1.13 | ColumnzxAnSwSubcardFirmwareFileType | read-only | current | This MIB is defined for the Firmware file type on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.3.1.14 | ColumnzxAnSwSubcardFirmwareVersion | read-only | current | This MIB is defined for the Firmware tag on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.3.1.15 | ColumnzxAnSwSubcardFirmwareFileLen | read-only | current | This MIB is defined for the Firmware file length on the card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.3.1.16 | ColumnzxAnSwSubcardFirmwareBuildTime | read-only | current | This MIB defines version build time.for example: yyyy-mm-dd HH:MM:SS.(2001-01-01 02:22:33). |
| 1.3.6.1.4.1.3902.1015.2.1.2.4 | TablezxAnVersionSavedTable | not-accessible | current | This table includes the saved version information in version area MP. |
| 1.3.6.1.4.1.3902.1015.2.1.2.4.1 | RowzxAnVersionSavedEntry | not-accessible | current | An entry in zxAnVersionSavedTable. |
| 1.3.6.1.4.1.3902.1015.2.1.2.4.1.1 | ColumnzxAnSwImageFileName | not-accessible | current | |
| 1.3.6.1.4.1.3902.1015.2.1.2.4.1.2 | ColumnzxAnSwImageFileType | read-only | current | This MIB is defined for the version file type on the saved area. |
| 1.3.6.1.4.1.3902.1015.2.1.2.4.1.3 | ColumnzxAnSwImageVersion | read-only | current | This MIB is defined for the version tag on the saved area. |
| 1.3.6.1.4.1.3902.1015.2.1.2.4.1.4 | ColumnzxAnSwImageFileLen | read-only | current | This MIB is defined for the version file length on the saved area. |
| 1.3.6.1.4.1.3902.1015.2.1.2.4.1.5 | ColumnzxAnSwImageBuildTime | read-only | current | This MIB defines version build time.for example: yyyy-mm-dd HH:MM:SS.(2001-01-01 02:22:33). |
| 1.3.6.1.4.1.3902.1015.2.1.2.4.1.6 | ColumnzxAnSwImageActiveStatus | read-write | current | This MIB is defined to admin saved MP version on the saved area. verSwap(1): swap the master and slave version of control card. inactive(2): inactive MP versio… |
| 1.3.6.1.4.1.3902.1015.2.1.2.4.1.7 | ColumnzxAnSwImageSyncToSecondary | read-write | current | Synchronize verion from master card to slave card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.4.1.8 | ColumnzxAnSwImageSyncToSecondaryStatus | read-only | current | Status of version synchronization from master card to slave card. |
| 1.3.6.1.4.1.3902.1015.2.1.2.4.1.9 | ColumnzxAnSavedTableType | read-only | current | This MIB is defined for savedTable type,1 indicate version and 2 indicate batch. |
| 1.3.6.1.4.1.3902.1015.2.1.2.4.1.10 | ColumnzxAnSavedFileDesc | not-accessible | current | This MIB is defined for the patch describe on the saved area. |
| 1.3.6.1.4.1.3902.1015.2.1.2.4.1.11 | ColumnzxAnSavedPatchParentVersion | read-only | current | This MIB is defined for the system version tag of the patch. |
| 1.3.6.1.4.1.3902.1015.2.1.2.4.1.12 | ColumnzxAnSavedPatchActiveTime | read-only | current | This MIB defines patch Active time.for example: yyyy-mm-dd HH:MM:SS.(2001-01-01 02:22:33). |
| 1.3.6.1.4.1.3902.1015.2.1.2.4.1.13 | ColumnzxAnSavedPatchActiveStatus | read-only | current | This MIB is defined for the patch active status. actived(1): actived but no save configuration. inactive(2) : inactive. autorun(3) : actived and save configura… |
| 1.3.6.1.4.1.3902.1015.2.1.2.4.1.14 | ColumnzxAnSavedPatchAdminStatus | read-write | current | This MIB is defined to admin saved MP patch on the saved area. active(1): active the master and slave patch of control card. deactivate(2) : deactivate the sav… |
| 1.3.6.1.4.1.3902.1015.2.1.2.4.1.15 | ColumnzxAnSavedAdminFailedReason | read-only | current | This MIB is defined for the operate failed reason. |
| 1.3.6.1.4.1.3902.1015.2.1.2.4.1.16 | ColumnzxAnSavedVersionDownloadTime | read-only | current | This MIB defines software file download time. for example: yyyy-mm-dd HH:MM:SS.(2001-01-01 02:22:33). |
| 1.3.6.1.4.1.3902.1015.2.1.2.5 | TablezxAnVersionUpdatingStatusTable | not-accessible | current | This table includes the version updating status information. |
| 1.3.6.1.4.1.3902.1015.2.1.2.5.1 | RowzxAnVersionUpdatingStatusEntry | not-accessible | current | An entry in zxAnVersionSavedTable. |
| 1.3.6.1.4.1.3902.1015.2.1.2.5.1.1 | ColumnzxAnSwManualUpdateSoftwareType | not-accessible | current | This MIB is defined for the version catalog when updating version. for example: BT:bootrom, FM:firmware, MVR:mainversion |
| 1.3.6.1.4.1.3902.1015.2.1.2.5.1.2 | ColumnzxAnSwManualUpdateStatus | read-only | current | This MIB is defined for the version status when updating version. negotiating(1):negotiating not starting downloading(2):updating from MP abort(3):update faile… |
| 1.3.6.1.4.1.3902.1015.2.1.2.5.1.3 | ColumnzxAnSwManualFailedReason | read-only | current | This MIB is defined for the reason when updating version failed. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6 | NodezxAnCpeSoftwareMgmt | |||
| 1.3.6.1.4.1.3902.1015.2.1.2.6.1 | TablezxAnCpeSwUpdateTaskTable | not-accessible | current | This table is the CPE software update table. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.1.1 | RowzxAnCpeSwUpdateTaskEntry | not-accessible | current | It is entry in the zxAnCpeSwUpdateTaskTable. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.1.1.1 | ColumnzxAnCpeSwUpdateTaskId | not-accessible | current | Name(unique) of CPEs software updating task and also for identifiying an entry in the table. e.g. 'F622-Version-Update'. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.1.1.2 | ColumnzxAnCpeSwUpdateTaskCreateTime | read-create | current | Create date of updating task. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.1.1.3 | ColumnzxAnCpeSwUpdateTaskDesc | read-create | current | Description of software updating task. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.1.1.4 | ColumnzxAnCpeSwUpdateTaskStatus | read-create | current | Status of software updaing task. 0xFFFF indicates status of 'NA'. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.1.1.5 | ColumnzxAnCpeSwUpdateTaskCpeCategory | read-create | current | Cpe category of software updating task. For example 'GPON ONT', 'EPON ONU', 'ADSL2+ Modem', 'VDSL2 Modem', Cpe category should be recognized by NE. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.1.1.6 | ColumnzxAnCpeSwUpdateTaskAdminStatus | read-create | current | Admin status of software updating task. Auto update policy will be disabled when aborting the task. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.1.1.7 | ColumnzxAnCpeSwUpdateTaskGranularity | read-create | current | Granularity of updating task. Only 'ne', 'olt', 'onuOrPort' granularities are supported by GPON NEs. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.1.1.8 | ColumnzxAnCpeSwUpdateTaskObjList | read-create | current | Update Object list of updating task and it has no meaning when 'zxAnCpeSwUpdateTaskObjectType' is setted as 'ne' granularity. If 'zxAnCpeSwUpdateTaskObjectType… |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.1.1.9 | ColumnzxAnCpeSwUpdateTaskCpeModel | read-create | current | Cpe model of updating task, e.g. 'F622'. One and only one cpe model can be set here. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.1.1.10 | ColumnzxAnCpeSwUpdateTaskCpeVersions | read-create | current | Cpe versions of updating task. More than one version can be set by this attribute, and comma should be used as separator between two versions, e.g. 'v1.2,v3.4,… |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.1.1.11 | ColumnzxAnCpeSwUpdateTaskVerFileName | read-create | current | Version file name of updating task. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.1.1.12 | ColumnzxAnCpeSwUpdateTaskVerFileLoc | read-create | current | Cpe version file location of updating task. If location is from ftp server, Ftp server ipaddress user password are setted by 'zxAnFtpVerServerIpAddress' 'zxAnF… |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.1.1.13 | ColumnzxAnCpeSwUpdateTaskFtpDir | read-create | current | Ftp direction when version file location is from ftp server. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.1.1.14 | ColumnzxAnCpeSwUpdateTaskExpiration | read-create | current | Expiration date of updating task. Both updating command and auto updating policy will be disabled automatically when datetime running over this date. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.1.1.15 | ColumnzxAnCpeSwUpdateTaskAutoDelete | read-create | current | If this attribute is true, task will be deleted by NE automatically when finishing updating. 'zxAnCpeSwUpdateTaskAutoUpdate' and this attribute can not set to … |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.1.1.16 | ColumnzxAnCpeSwUpdateTaskAutoUpdate | read-create | current | If this attribute is true, Software of cpe will be auto updated when its status is from down to up. 'zxAnCpeSwUpdateTaskAutoDelete' and this attribure cat not … |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.1.1.25 | ColumnzxAnCpeSwUpdateTaskRowStatus | read-create | current | This attribute is used to 'create','delete' task. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.2 | TablezxAnCpeSwUpdateTaskStatTable | not-accessible | current | This table indicates the interface to query statistics of software updating task. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.2.1 | RowzxAnCpeSwUpdateTaskStatEntry | not-accessible | current | It is entry in the zxAnCpeSwUpdateTaskStatEntry. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.2.1.1 | ColumnzxAnCpeSwUpateTotals | read-only | current | Total count of cpe in the task. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.2.1.2 | ColumnzxAnCpeSwUpdateSucceeds | read-only | current | Count of successfully updated cpe and those updated by auto update policy are included in this count. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.2.1.3 | ColumnzxAnCpeSwUpdatings | read-only | current | Count of updating cpe. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.2.1.4 | ColumnzxAnCpeSwUpdateFails | read-only | current | Count of failed updated cpe and those updated failed by auto update policy are included in this count. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.2.1.5 | ColumnzxAnCpeSwAutoUpdateSucceeds | read-only | current | Count of successfully updated cpe by auto update policy. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.3 | TablezxAnCpeSwUpdateTaskFailedTable | not-accessible | current | This table is for querying failed CPEs of software updating task. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.3.1 | RowzxAnCpeSwUpdateTaskFailedEntry | not-accessible | current | It is entry in the zxAnCpeSwUpdateFailedTable. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.3.1.1 | ColumnzxAnCpeSwRackNo | not-accessible | current | This object indicates the rack number. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.3.1.2 | ColumnzxAnCpeSwShelfNo | not-accessible | current | This object indicates the shelf number. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.3.1.3 | ColumnzxAnCpeSwSlotNo | not-accessible | current | This object indicates the slot number. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.3.1.4 | ColumnzxAnCpeSwPortNo | not-accessible | current | This object indicates the physical port number. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.3.1.5 | ColumnzxAnCpeSwOnuNo | not-accessible | current | When zxAnCpeSwCircuitType are 'onu' or 'gemportOrLlid' or 'servicePort' this object indicates 'onu ID'. When zxAnCpeSwCircuitType are 'physicalPort' or 'bridge… |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.3.1.6 | ColumnzxAnCpeSwCircuitType | not-accessible | current | This object indicates the type of port. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.3.1.7 | ColumnzxAnCpeSwUpdateTaskFailCpeName | read-only | current | Name of the failed updated cpe. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.3.1.8 | ColumnzxAnCpeSwUpdateTaskFailReason | read-only | current | Failed reason of software updating. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.4 | TablezxAnCpeSwStatusTable | not-accessible | current | This table is cpe software status table, software updating status is included in it. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.4.1 | RowzxAnCpeSwStatusEntry | not-accessible | current | It is entry in the zxAnCpeSwStatusTable. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.4.1.1 | ColumnzxAnCpeSwCpeName | read-only | current | The name of cpe. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.4.1.2 | ColumnzxAnCpeSwUpdateStatus | read-only | current | Status of cpe software update. 0xFFFF indicates status of 'NA'. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.4.1.3 | ColumnzxAnCpeSwUpdateFailReason | read-only | current | The failed reason cpe software update. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.4.1.4 | ColumnzxAnCpeSwUpdateProgress | read-only | current | Progress of cpe software update. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.4.1.5 | ColumnzxAnCpeSwCurrVer | read-only | current | The version No. of the software current used. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.4.1.6 | ColumnzxAnCpeSwCurrVerBuildTime | read-only | current | The build time of the software current used. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.4.1.7 | ColumnzxAnCpeSwUpdatingVer | read-only | current | The version No. of the software updating. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.4.1.8 | ColumnzxAnCpeSwUpdatingVerBuildTime | read-only | current | The build time of the software updating. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.4.1.9 | ColumnzxAnCpeSwVendorId | read-only | current | The vendor id of cpe. |
| 1.3.6.1.4.1.3902.1015.2.1.2.6.4.1.10 | ColumnzxAnCpeSwProductId | read-only | current | The product id of cpe. |
| 1.3.6.1.4.1.3902.1015.2.1.2.7 | NodezxAnVerAutoUpdateMgmt | |||
| 1.3.6.1.4.1.3902.1015.2.1.2.7.1 | ScalarzxAnVerAutoUpdateBootUpdateEn | read-write | current | Enable or disable the boot update function. |
| 1.3.6.1.4.1.3902.1015.2.1.2.7.2 | ScalarzxAnVerAutoUpdateVerBackupEn | read-write | current | Enable or disable the version backup function. |
| 1.3.6.1.4.1.3902.1015.2.1.2.7.3 | ScalarzxAnVerAutoUpdateVersionPath | read-write | current | The path defines the relative directory below the FTP user directory, where the version file saved in the FTP Server. |
| 1.3.6.1.4.1.3902.1015.2.1.2.7.4 | ScalarzxAnVerAutoUpdateBackupPath | read-write | current | The path defines the relative directory below the FTP user directory, where the backup file saved in the FTP Server. |
| 1.3.6.1.4.1.3902.1015.2.1.2.7.5 | ScalarzxAnVerAutoUpdateLogPath | read-write | current | The path defines the relative directory below the FTP user directory, where the log file saved in the FTP Server. |
| 1.3.6.1.4.1.3902.1015.2.1.2.7.6 | ScalarzxAnVerAutoUpdateAction | read-write | current | The auto update action. 1 means to start the auto update progress. |
| 1.3.6.1.4.1.3902.1015.2.1.2.7.7 | ScalarzxAnVerAutoUpdateStatus | read-only | current | This variable represents the auto update status. |
| 1.3.6.1.4.1.3902.1015.2.1.2.7.8 | ScalarzxAnVerAutoUpdateFailedReason | read-only | current | This variable represents the failed reason. |
| 1.3.6.1.4.1.3902.1015.2.1.3 | NodezxAnEnvMonitor | |||
| 1.3.6.1.4.1.3902.1015.2.1.3.1 | ScalarzxAnEnvMgmtCapabilities | read-only | current | The enviroment management capabilities of this equipment. The bit value 1 means the function represented by this bit is supported by this equipment. NOTE: No r… |
| 1.3.6.1.4.1.3902.1015.2.1.3.2 | ScalarzxAnEnvTemperature | read-only | current | The temperature of the enviroment. |
| 1.3.6.1.4.1.3902.1015.2.1.3.3 | ScalarzxAnEnvTemperatureAlarmThreshold | read-write | current | The temperature alarm threshold of the enviroment. |
| 1.3.6.1.4.1.3902.1015.2.1.3.4 | ScalarzxAnEnvMonitorInterfaceUsage | read-write | current | The equipment type connected to the enviroment monitor interface. NOTE: No recomanded to display it in NMS. |
| 1.3.6.1.4.1.3902.1015.2.1.3.5 | ScalarzxAnMPTemperature | read-only | current | The temperature of the MP. Unit is C |
| 1.3.6.1.4.1.3902.1015.2.1.3.6 | ScalarzxAnMPTemperatureAlarmThreshold | read-write | current | The temperature alarm threshold of the MP. Unit is C |
| 1.3.6.1.4.1.3902.1015.2.1.3.7 | ScalarzxAnEpmConnectPort | read-write | current | The port no which epm connect |
| 1.3.6.1.4.1.3902.1015.2.1.3.8 | ScalarzxAnEnvBackplaneInterfaceUsage | read-write | current | The equipment type connected to the Backplane Interface. fan(1): the fan connect to the Backplane Interface; noUse(3): not used; noSupport(255):not support. |
| 1.3.6.1.4.1.3902.1015.2.1.3.9 | NodezxAnEnvPowerSupplyMgmt | |||
| 1.3.6.1.4.1.3902.1015.2.1.3.9.1 | ScalarzxAnPowerSupplyCount | read-only | current | The number of entries in the zxAnPowerSupplyTable. |
| 1.3.6.1.4.1.3902.1015.2.1.3.9.2 | TablezxAnPowerSupplyTable | not-accessible | current | The power supply table. |
| 1.3.6.1.4.1.3902.1015.2.1.3.9.2.1 | RowzxAnPowerSupplyEntry | not-accessible | current | An entry in the power supply table. |
| 1.3.6.1.4.1.3902.1015.2.1.3.9.2.1.1 | ColumnzxAnPowerSupplyInVoltageStatus | read-only | current | The volt staus of the power supply. |
| 1.3.6.1.4.1.3902.1015.2.1.3.9.2.1.2 | ColumnzxAnPowerSupplyOperState | read-only | current | The operational state of the power supply module. |
| 1.3.6.1.4.1.3902.1015.2.1.3.9.2.1.3 | ColumnzxAnPowerSupplyInVoltage | read-only | current | The actual input volts of the power supply module. |
| 1.3.6.1.4.1.3902.1015.2.1.3.9.2.1.4 | ColumnzxAnPowerInVoltageUpperThresh | read-write | current | The upper threshold of input volts.The alarm should be generated when zxAnPowerSupplyInVolts exceeds this threshold. If it is 0, no alarm reported to manager. |
| 1.3.6.1.4.1.3902.1015.2.1.3.9.2.1.5 | ColumnzxAnPowerInVoltageLowerThresh | read-write | current | The lower threshold of input volts.The alarm should be generated when zxAnPowerSupplyInVolts is lower than this threshold. If it is 0, no alarm reported to man… |
| 1.3.6.1.4.1.3902.1015.2.1.3.9.2.1.6 | ColumnzxAnPowerSupplyInCurrent | read-only | current | The actual current of the power supply module. |
| 1.3.6.1.4.1.3902.1015.2.1.3.9.2.1.7 | ColumnzxAnPowerInCurrentThresh | read-write | current | The upper threshold of input current.The alarm should be generated when zxAnPowerSupplyInCurrent exceeds this threshold. If it is 0, no alarm reported to manag… |
| 1.3.6.1.4.1.3902.1015.2.1.3.9.2.1.8 | ColumnzxAnPowerSupplyInPower | read-only | current | The actual power of the power supply module. |
| 1.3.6.1.4.1.3902.1015.2.1.3.10 | NodezxAnEnvFanMgmt | |||
| 1.3.6.1.4.1.3902.1015.2.1.3.10.1 | ScalarzxAnEnvFanAlarmBeepEnable | read-write | current | The control status of the fan alarm beep. |
| 1.3.6.1.4.1.3902.1015.2.1.3.10.2 | ScalarzxAnEnvFanAutoSwitchByCardInst | read-write | current | Enable/disable fan auto switch with card installation. If it is enabled,the fan under the card should be swiched to running status when the card is installed.O… |
| 1.3.6.1.4.1.3902.1015.2.1.3.10.3 | ScalarzxAnEnvFanTrayHardwareVersion | read-only | current | The hardware version of the fan tray |
| 1.3.6.1.4.1.3902.1015.2.1.3.10.4 | ScalarzxAnEnvFanTraySoftwareVersion | read-only | current | The software version of the fan tray |
| 1.3.6.1.4.1.3902.1015.2.1.3.10.5 | ScalarzxAnEnvFanInvSn | read-write | current | The serial number of fan board.It used by inventory management. |
| 1.3.6.1.4.1.3902.1015.2.1.3.10.10 | NodezxAnEnvFanSpeedCtrlMgmt | |||
| 1.3.6.1.4.1.3902.1015.2.1.3.10.10.1 | ScalarzxAnEnvFanSpeedCtrlMode | read-write | current | The speed control mode of the fan. |
| 1.3.6.1.4.1.3902.1015.2.1.3.10.10.2 | ScalarzxAnEnvFanLowSpeed | read-write | current | The speed value of the fan's low speed level. The values for ZXDSL9800,9210 are 1500,2400,2700,3000,3400,3700, 4000,4400. NOTE: No recomanded to display it in … |
| 1.3.6.1.4.1.3902.1015.2.1.3.10.10.3 | ScalarzxAnEnvFanStandardSpeed | read-write | current | The speed value of the fan's standard speed level. The values for ZXDSL9800,9210 are 1500,2400,2700,3000,3400,3700, 4000,4400. NOTE: No recomanded to display i… |
| 1.3.6.1.4.1.3902.1015.2.1.3.10.10.4 | ScalarzxAnEnvFanHighSpeed | read-write | current | The speed value of the fan's high speed level. The values for ZXDSL9800,9210 are 1500,2400,2700,3000,3400,3700, 4000,4400. NOTE: No recomanded to display it in… |
| 1.3.6.1.4.1.3902.1015.2.1.3.10.10.5 | ScalarzxAnEnvFanSuperSpeed | read-write | current | The speed value of the fan's super speed level. The values for ZXDSL9800,9210 are 1500,2400,2700,3000,3400,3700, 4000,4400. NOTE: No recomanded to display it i… |
| 1.3.6.1.4.1.3902.1015.2.1.3.10.10.6 | ScalarzxAnEnvFanLowSpeedShiftTem | read-write | current | The temperature to activate the fan tray to shift to the low speed level. NOTE: No recomanded to display it in NMS. |
| 1.3.6.1.4.1.3902.1015.2.1.3.10.10.7 | ScalarzxAnEnvFanStdSpeedShiftTem | read-write | current | The temperature to activate the fan tray to shift to the standard speed level. NOTE: No recomanded to display it in NMS. |
| 1.3.6.1.4.1.3902.1015.2.1.3.10.10.8 | ScalarzxAnEnvFanHighSpeedShiftTem | read-write | current | The temperature to activate the fan tray to shift to the high speed level. NOTE: No recomanded to display it in NMS. |
| 1.3.6.1.4.1.3902.1015.2.1.3.10.10.9 | ScalarzxAnEnvFanSuperSpeedShiftTem | read-write | current | The temperature to activate the fan tray to shift to the super speed level. NOTE: No recomanded to display it in NMS. |
| 1.3.6.1.4.1.3902.1015.2.1.3.10.10.10 | TablezxAnEnvFanTable | not-accessible | current | This table includes speed information and operational status of the fan. |
| 1.3.6.1.4.1.3902.1015.2.1.3.10.10.10.1 | RowzxAnEnvFanEntry | not-accessible | current | The entry of zxAnEnvFanTable. |
| 1.3.6.1.4.1.3902.1015.2.1.3.10.10.10.1.1 | ColumnzxAnEnvFanIndex | not-accessible | current | The index of this fan. |
| 1.3.6.1.4.1.3902.1015.2.1.3.10.10.10.1.2 | ColumnzxAnEnvFanConfSpeedLevel | read-create | current | The configured speed level of the fan. NOTE: No recomanded to display it in NMS. |
| 1.3.6.1.4.1.3902.1015.2.1.3.10.10.10.1.3 | ColumnzxAnEnvFanActualSpeedLevel | read-only | current | The actual speed level of the fan. |
| 1.3.6.1.4.1.3902.1015.2.1.3.10.10.10.1.4 | ColumnzxAnEnvFanAdminStatus | read-create | current | The administrative status of the fan. NOTE: No recomanded to configure it in NMS. |
| 1.3.6.1.4.1.3902.1015.2.1.3.10.10.10.1.5 | ColumnzxAnEnvFanOperStatus | read-only | current | The operational status of the fan. |
| 1.3.6.1.4.1.3902.1015.2.1.3.10.10.10.1.6 | ColumnzxAnEnvFanOnlineStatus | read-only | current | The actual online status of the fan. |
| 1.3.6.1.4.1.3902.1015.2.1.3.10.10.10.1.7 | ColumnzxAnEnvFanActualSpeed | read-only | current | The actual speed of the fan. NOTE: If not supported, NMS should use the speed value of zxAnEnvFanActualSpeedLevel |
| 1.3.6.1.4.1.3902.1015.2.1.3.10.10.11 | ScalarzxAnEnvFanLowSpeedPercentage | read-write | current | The percentage of speed of the low speed level. |
| 1.3.6.1.4.1.3902.1015.2.1.3.10.10.12 | ScalarzxAnEnvFanStandardSpeedPercent | read-write | current | The percentage of speed of the standard speed level. |
| 1.3.6.1.4.1.3902.1015.2.1.3.10.10.13 | ScalarzxAnEnvFanHighSpeedPercentage | read-write | current | The percentage of speed of the high speed level. |
| 1.3.6.1.4.1.3902.1015.2.1.3.10.10.14 | ScalarzxAnEnvFanSuperSpeedPercentage | read-write | current | The percentage of speed of the super speed level. |
| 1.3.6.1.4.1.3902.1015.2.1.3.11 | NodezxAnEnvDustCapMgmt | |||
| 1.3.6.1.4.1.3902.1015.2.1.3.11.1 | ScalarzxAnEnvDustCapOperStatus | read-write | current | The operational status of the dust cap. |
| 1.3.6.1.4.1.3902.1015.2.1.3.12 | ScalarzxAnEnvMonitorIfTrapEnable | read-write | current | For F820, enable or disable the EPM link up/down trap. |
| 1.3.6.1.4.1.3902.1015.2.1.3.13 | NodezxAnEnvCardMgmt | |||
| 1.3.6.1.4.1.3902.1015.2.1.3.13.5 | TablezxAnEnvCardTemperatureTable | not-accessible | current | This table includes card temperature information. |
| 1.3.6.1.4.1.3902.1015.2.1.3.13.5.1 | RowzxAnEnvCardTemperatureEntry | not-accessible | current | The entry of zxAnEnvCardTemperatureTable. |
| 1.3.6.1.4.1.3902.1015.2.1.3.13.5.1.1 | ColumnzxAnEnvCardTemperature | read-only | current | The temperature of the card enviroment. |
| 1.3.6.1.4.1.3902.1015.2.1.3.14 | NodezxAnEnvOverheatProtectionMgmt | |||
| 1.3.6.1.4.1.3902.1015.2.1.3.14.1 | NodezxAnEnvOverheatProtectionObjects | |||
| 1.3.6.1.4.1.3902.1015.2.1.3.14.1.1 | ScalarzxAnEnvOverheatProtectionEnable | read-write | current | Enables or disables the overheat protection function. |
| 1.3.6.1.4.1.3902.1015.2.1.3.14.1.2 | ScalarzxAnEnvOverheatTmpThreshold | read-write | current | The threshold of the temperature. MSAG5208:Broadband service of all cards will be stopped when the temperature is above zxAnEnvOverheatTmpThreshold. C300:Card … |
| 1.3.6.1.4.1.3902.1015.2.1.3.14.1.3 | ScalarzxAnEnvOverheatDurThreshold | read-write | current | The threshold of the duration. Narrowband service of all cards will be stopped when the temperature is above zxAnEnvOverheatTmpThreshold and the high temperatu… |
| 1.3.6.1.4.1.3902.1015.2.1.3.14.1.25 | ScalarzxAnEnvOverheatAutoRecoveryType | read-write | current | Automatic recovery condition, below zxAnEnvAutoRecoveryTmpThreshold or after zxAnEnvOverheatAutoRecoveryTime. C300 only supports byTime, MSAG5200V3 only suppor… |
| 1.3.6.1.4.1.3902.1015.2.1.3.14.1.30 | ScalarzxAnEnvOverheatAutoRecoveryEn | read-write | current | Enables or disables the automatic recovery service function. Not used for C300. |
| 1.3.6.1.4.1.3902.1015.2.1.3.14.1.31 | ScalarzxAnEnvAutoRecoveryTmpThreshold | read-write | current | The threshold of the temperature. Broadband and narrowband service of all cards will be restarted when the temperature is below it. Only valid when zxAnEnvOver… |
| 1.3.6.1.4.1.3902.1015.2.1.3.14.1.40 | ScalarzxAnEnvOverheatAutoRecoveryTime | read-write | current | Card will be supplied with power zxAnEnvOverheatAutoRecoveryTime later. Only used for C300. |
| 1.3.6.1.4.1.3902.1015.2.1.3.14.1.50 | ScalarzxAnEnvOverheatProtectionStatus | read-only | current | The status of the protection. Not used for C300. |
| 1.3.6.1.4.1.3902.1015.2.1.3.15 | NodezxAnEnvBatteryObjects | |||
| 1.3.6.1.4.1.3902.1015.2.1.3.15.1 | NodezxAnEnvBatteryGlobalObjects | |||
| 1.3.6.1.4.1.3902.1015.2.1.3.15.1.1 | ScalarzxAnEnvBatteryEnergySavingEnable | read-write | current | Enables or disables the battery energy saving. |
| 1.3.6.1.4.1.3902.1015.2.1.3.16 | NodezxAnEnvDeviceObjects | |||
| 1.3.6.1.4.1.3902.1015.2.1.3.16.2 | TablezxAnEnvDeviceTable | not-accessible | current | The table of environment device. |
| 1.3.6.1.4.1.3902.1015.2.1.3.16.2.1 | RowzxAnEnvDeviceEntry | not-accessible | current | The entry of this table. |
| 1.3.6.1.4.1.3902.1015.2.1.3.16.2.1.1 | ColumnzxAnEnvDeviceId | not-accessible | current | The id of this environment device. Value 1-50 is default value which can not be modified or deleted. If add a new device, the id will be starting from 51. |
| 1.3.6.1.4.1.3902.1015.2.1.3.16.2.1.2 | ColumnzxAnEnvDeviceName | read-create | current | The name of the environment device. |
| 1.3.6.1.4.1.3902.1015.2.1.3.16.2.1.50 | ColumnzxAnEnvDeviceRowStatus | read-create | current | The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a man… |
| 1.3.6.1.4.1.3902.1015.2.1.3.16.3 | TablezxAnEnvDevMonSwitchTable | not-accessible | current | The table of the switch which monitor environment device. |
| 1.3.6.1.4.1.3902.1015.2.1.3.16.3.1 | RowzxAnEnvDevMonSwitchEntry | not-accessible | current | The entry of the table. |
| 1.3.6.1.4.1.3902.1015.2.1.3.16.3.1.1 | ColumnzxAnEnvDevMonSwitchId | not-accessible | current | The id of the switch. |
| 1.3.6.1.4.1.3902.1015.2.1.3.16.3.1.2 | ColumnzxAnEnvDevMonSwitchDeviceId | read-write | current | The id of the device which monitored by the switch. Value 0 means this switch does not monitor any device. |
| 1.3.6.1.4.1.3902.1015.2.1.3.16.3.1.3 | ColumnzxAnEnvDevMonSwitchTrapEnable | read-write | current | Enables and disables the environment device abnormal trap. |
| 1.3.6.1.4.1.3902.1015.2.1.3.16.3.1.4 | ColumnzxAnEnvDevMonSwitchNormalStatus | read-write | current | The normal status of the environment device. |
| 1.3.6.1.4.1.3902.1015.2.1.3.16.3.1.5 | ColumnzxAnEnvDevMonSwitchCurrStatus | read-only | current | The current status of the environment device. |
| 1.3.6.1.4.1.3902.1015.2.1.4 | NodezxAnPatchMgmt | |||
| 1.3.6.1.4.1.3902.1015.2.1.4.1 | TablezxAnPatchTable | not-accessible | current | A table entry containing patch information. |
| 1.3.6.1.4.1.3902.1015.2.1.4.1.1 | RowzxAnPatchEntry | not-accessible | current | patch information entry |
| 1.3.6.1.4.1.3902.1015.2.1.4.1.1.1 | ColumnzxAnPatchName | not-accessible | current | the file name of the patch |
| 1.3.6.1.4.1.3902.1015.2.1.4.1.1.2 | ColumnzxAnPatchSystemVersion | read-only | current | the system version of the patch |
| 1.3.6.1.4.1.3902.1015.2.1.4.1.1.3 | ColumnzxAnPatchVersionNo | read-only | current | the version no of the patch |
| 1.3.6.1.4.1.3902.1015.2.1.4.1.1.4 | ColumnzxAnPatchSize | read-only | current | the version length of the patch |
| 1.3.6.1.4.1.3902.1015.2.1.4.1.1.5 | ColumnzxAnPatchStatus | read-only | current | the status of the patch, such as activated, deactivated and autorun |
| 1.3.6.1.4.1.3902.1015.2.1.4.1.1.6 | ColumnzxAnPatchCreateTime | read-only | current | the patch create time |
| 1.3.6.1.4.1.3902.1015.2.1.4.1.1.7 | ColumnzxAnPatchActiveTime | read-only | current | the patch active time |
| 1.3.6.1.4.1.3902.1015.2.1.4.1.1.8 | ColumnzxAnPatchRunningTime | read-only | current | the running time of the patch |
| 1.3.6.1.4.1.3902.1015.2.1.4.1.1.9 | ColumnzxAnPatchDesc | read-only | current | the patch description |
| 1.3.6.1.4.1.3902.1015.2.1.4.1.1.10 | ColumnzxAnPatchAdminStatus | read-write | current | config the status of patch |
| 1.3.6.1.4.1.3902.1015.2.1.5 | NodezxAnEquipStat | |||
| 1.3.6.1.4.1.3902.1015.2.1.5.1 | TablezxAnCardStatTable | not-accessible | current | The card statistic table. |
| 1.3.6.1.4.1.3902.1015.2.1.5.1.1 | RowzxAnCardStatEntry | not-accessible | current | An entry in the card statistic table . |
| 1.3.6.1.4.1.3902.1015.2.1.5.1.1.1 | ColumnzxAnCardInOctets | read-only | current | The total number of octets received of current card. |
| 1.3.6.1.4.1.3902.1015.2.1.5.1.1.2 | ColumnzxAnCardInUcastPkts | read-only | current | The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. |
| 1.3.6.1.4.1.3902.1015.2.1.5.1.1.3 | ColumnzxAnCardInMulticastPkts | read-only | current | The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer prot… |
| 1.3.6.1.4.1.3902.1015.2.1.5.1.1.4 | ColumnzxAnCardInBroadcastPkts | read-only | current | The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. This object is a 64-… |
| 1.3.6.1.4.1.3902.1015.2.1.5.1.1.5 | ColumnzxAnCardOutOctets | read-only | current | The total number of octets transmitted out of current card. |
| 1.3.6.1.4.1.3902.1015.2.1.5.1.1.6 | ColumnzxAnCardOutUcastPkts | read-only | current | The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-… |
| 1.3.6.1.4.1.3902.1015.2.1.5.1.1.7 | ColumnzxAnCardOutMulticastPkts | read-only | current | The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including … |
| 1.3.6.1.4.1.3902.1015.2.1.5.1.1.8 | ColumnzxAnCardOutBroadcastPkts | read-only | current | The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including … |
| 1.3.6.1.4.1.3902.1015.2.1.5.1.1.9 | ColumnzxAnCardInErrors | read-only | current | The total number of errored packets received on the card, including framing characters. Discontinuities in the value of this counter can occur at re-initializa… |
| 1.3.6.1.4.1.3902.1015.2.1.5.1.1.10 | ColumnzxAnCardOutErrors | read-only | current | The total number of errored packets transmitted out of the card, including framing characters. Discontinuities in the value of this counter can occur at re-ini… |
| 1.3.6.1.4.1.3902.1015.2.1.5.1.1.11 | ColumnzxAnCardInDiscardPkts | read-only | current | The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer pr… |
| 1.3.6.1.4.1.3902.1015.2.1.5.1.1.12 | ColumnzxAnCardOutDiscardPkts | read-only | current | The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reaso… |
| 1.3.6.1.4.1.3902.1015.2.1.5.1.1.13 | ColumnzxAnCardInDiscardPktRatio | read-only | current | An estimate of the card's discarded packets ratio received. The value equals (received discarded packets / number of total received packets) * 100%. |
| 1.3.6.1.4.1.3902.1015.2.1.5.1.1.14 | ColumnzxAnCardOutDiscardPktRatio | read-only | current | An estimate of the card's discarded packets ratio being transmitted. The value equals (number of transmitted discarded packets / number of total transmitted pa… |
| 1.3.6.1.4.1.3902.1015.2.1.5.1.1.15 | ColumnzxAnCardDot3InPauseFrames | read-only | current | A count of MAC Control frames received on current card with an opcode indicating the PAUSE operation. |
| 1.3.6.1.4.1.3902.1015.2.1.5.1.1.16 | ColumnzxAnCardDot3OutPauseFrames | read-only | current | A count of MAC Control frames transmitted on current card with an opcode indicating the PAUSE operation. |
| 1.3.6.1.4.1.3902.1015.2.1.6 | NodezxAnEquipSysMgmt | |||
| 1.3.6.1.4.1.3902.1015.2.1.6.1 | ScalarzxAnEquipSysLastSwapRequest | read-only | current | Last swap request,such as force,plug-out or others. |
| 1.3.6.1.4.1.3902.1015.2.1.6.10 | ScalarzxAnEquipSysAutoSwapEnable | read-write | current | Enable and disable auto swap function. |
| 1.3.6.1.4.1.3902.1015.2.1.6.11 | ScalarzxAnEquipSysAutoSwapStartTime | read-write | current | The start time of day to auto swap. For example:HH:MM:SS(02:22:33). This variable is valid if zxAnEquipSysAutoSwapEnable is set to enable(1). |
| 1.3.6.1.4.1.3902.1015.2.1.6.12 | ScalarzxAnEquipSysAutoSwapInterval | read-write | current | The interval of auto swap. This variable is valid if zxAnEquipSysAutoSwapEnable is set to enable(1). |
| 1.3.6.1.4.1.3902.1015.2.1.6.13 | ScalarzxAnEquipSysAutoSwapRemainDays | read-only | current | The remaining days of the next auto swap. This variable is valid if zxAnEquipSysAutoSwapEnable is set to enable(1). |
| 1.3.6.1.4.1.3902.1015.2.1.6.14 | ScalarzxAnEquipShelfAutoSwapInterval | read-write | current | The interval of automatic swap between shelves. This variable is valid if zxAnEquipSysAutoSwapEnable is set to enable(1). |
| 1.3.6.1.4.1.3902.1015.2.1.7 | NodezxAnEnvExMonitor | |||
| 1.3.6.1.4.1.3902.1015.2.1.7.1 | NodezxAnEnvExMgmt | |||
| 1.3.6.1.4.1.3902.1015.2.1.7.1.1 | TablezxAnEnvExMgmtTable | not-accessible | current | The environment management table, with rack and shelf information. |
| 1.3.6.1.4.1.3902.1015.2.1.7.1.1.1 | RowzxAnEnvExMgmtEntry | not-accessible | current | An entry in the zxAnEnvExMgmtTable. |
| 1.3.6.1.4.1.3902.1015.2.1.7.1.1.1.1 | ColumnzxAnEnvExTemperature | read-only | current | The temperature of the enviroment. Unit is C |
| 1.3.6.1.4.1.3902.1015.2.1.7.1.1.1.2 | ColumnzxAnEnvExTempAlarmThreshold | read-write | current | The temperature alarm threshold of the enviroment. Unit is C |
| 1.3.6.1.4.1.3902.1015.2.1.7.1.1.1.3 | ColumnzxAnEnvExMonitorIfUsage | read-write | current | The equipment type connected to the enviroment monitor interface. |
| 1.3.6.1.4.1.3902.1015.2.1.7.1.2 | NodezxAnEnvExTempCtrlMgmt | |||
| 1.3.6.1.4.1.3902.1015.2.1.7.1.2.2 | TablezxAnEnvExTempCtrlTable | not-accessible | current | The table of temperature control objects. |
| 1.3.6.1.4.1.3902.1015.2.1.7.1.2.2.1 | RowzxAnEnvExTempCtrlEntry | not-accessible | current | The entry of zxAnEnvExTempCtrlTable. |
| 1.3.6.1.4.1.3902.1015.2.1.7.1.2.2.1.1 | ColumnzxAnEnvExTempCtrlEnable | read-write | current | Enable/disable the function of temperature control. |
| 1.3.6.1.4.1.3902.1015.2.1.7.1.2.2.1.2 | ColumnzxAnEnvExTempCtrlLowThresh | read-write | current | The low temperature threshold of temperature control. When zxAnEnvExTemperature reaches the value and lower than zxAnEnvExTempCtrlMediumThresh, and zxAnEnvExTe… |
| 1.3.6.1.4.1.3902.1015.2.1.7.1.2.2.1.3 | ColumnzxAnEnvExTempCtrlMediumThresh | read-write | current | The medium tempertaure threshold of temperature control. When zxAnEnvExTemperature reaches zxAnEnvExTempCtrlMediumThresh and lower than zxAnEnvExTempCtrlHighTh… |
| 1.3.6.1.4.1.3902.1015.2.1.7.1.2.2.1.4 | ColumnzxAnEnvExTempCtrlHighThresh | read-write | current | The high tempertaure threshold of temperature control. When zxAnEnvExTemperature above the threshold, and zxAnEnvExTempCtrlEnable is enabled, system will reboo… |
| 1.3.6.1.4.1.3902.1015.2.1.7.2 | NodezxAnFanTrayExMgmt | |||
| 1.3.6.1.4.1.3902.1015.2.1.7.2.1 | TablezxAnFanTrayExMgmtTable | not-accessible | current | The Fan Control table, with rack and shelf information. |
| 1.3.6.1.4.1.3902.1015.2.1.7.2.1.1 | RowzxAnFanTrayExMgmtEntry | not-accessible | current | An entry in the zxAnFanTrayExMgmtTable. |
| 1.3.6.1.4.1.3902.1015.2.1.7.2.1.1.1 | ColumnzxAnFanExAlarmBeepEnable | read-write | current | The control status of the fan alarm beep. |
| 1.3.6.1.4.1.3902.1015.2.1.7.2.1.1.2 | ColumnzxAnFanExAutoSwitchByCardInstall | read-write | current | Enable/disable fan auto switch with card installation. If it is enabled,the fan under the card should be swiched to running status when the card is installed.O… |
| 1.3.6.1.4.1.3902.1015.2.1.7.2.1.1.3 | ColumnzxAnFanExHardwareVersion | read-only | current | The hardware version of the fan tray |
| 1.3.6.1.4.1.3902.1015.2.1.7.2.1.1.4 | ColumnzxAnFanExSoftwareVersion | read-only | current | The software version of the fan tray |
| 1.3.6.1.4.1.3902.1015.2.1.7.2.1.1.5 | ColumnzxAnFanExSpeedCtrlMode | read-write | current | The speed control mode of the fan. |
| 1.3.6.1.4.1.3902.1015.2.1.7.2.1.1.6 | ColumnzxAnFanExLowSpeed | read-write | current | The speed value of the fan's low speed level. The values for ZXDSL9800,9210 are 1500,2400,2700,3000,3400,3700, 4000,4400. NOTE: No recomanded to display it in … |
| 1.3.6.1.4.1.3902.1015.2.1.7.2.1.1.7 | ColumnzxAnFanExStandardSpeed | read-write | current | The speed value of the fan's standard speed level. The values for ZXDSL9800,9210 are 1500,2400,2700,3000,3400,3700, 4000,4400. NOTE: No recomanded to display i… |
| 1.3.6.1.4.1.3902.1015.2.1.7.2.1.1.8 | ColumnzxAnFanExHighSpeed | read-write | current | The speed value of the fan's high speed level. The values for ZXDSL9800,9210 are 1500,2400,2700,3000,3400,3700, 4000,4400. NOTE: No recomanded to display it in… |
| 1.3.6.1.4.1.3902.1015.2.1.7.2.1.1.9 | ColumnzxAnFanExSuperSpeed | read-write | current | The speed value of the fan's super speed level. The values for ZXDSL9800,9210 are 1500,2400,2700,3000,3400,3700, 4000,4400. NOTE: No recomanded to display it i… |
| 1.3.6.1.4.1.3902.1015.2.1.7.2.1.1.10 | ColumnzxAnFanExLowSpeedShiftTemp | read-write | current | The temperature to activate the fan tray to shift to the low speed level. NOTE: No recomanded to display it in NMS. |
| 1.3.6.1.4.1.3902.1015.2.1.7.2.1.1.11 | ColumnzxAnFanExStandardSpeedShiftTemp | read-write | current | The temperature to activate the fan tray to shift to the standard speed level. NOTE: No recomanded to display it in NMS. |
| 1.3.6.1.4.1.3902.1015.2.1.7.2.1.1.12 | ColumnzxAnFanExHighSpeedShiftTemp | read-write | current | The temperature to activate the fan tray to shift to the high speed level. NOTE: No recomanded to display it in NMS. |
| 1.3.6.1.4.1.3902.1015.2.1.7.2.1.1.13 | ColumnzxAnFanExSuperSpeedShiftTemp | read-write | current | The temperature to activate the fan tray to shift to the super speed level. NOTE: No recomanded to display it in NMS. |
| 1.3.6.1.4.1.3902.1015.2.1.7.2.1.1.14 | ColumnzxAnFanExLowSpeedPercentage | read-write | current | The percentage of speed of the low speed level. |
| 1.3.6.1.4.1.3902.1015.2.1.7.2.1.1.15 | ColumnzxAnFanExStandardSpeedPercentage | read-write | current | The percentage of speed of the standard speed level. |
| 1.3.6.1.4.1.3902.1015.2.1.7.2.1.1.16 | ColumnzxAnFanExHighSpeedPercentage | read-write | current | The percentage of speed of the high speed level. |
| 1.3.6.1.4.1.3902.1015.2.1.7.2.1.1.17 | ColumnzxAnFanExSuperSpeedPercentage | read-write | current | The percentage of speed of the super speed level. |
| 1.3.6.1.4.1.3902.1015.2.1.7.2.1.1.18 | ColumnzxAnFanExInvSn | read-write | current | The serial number of fan board.It used by inventory management. |
| 1.3.6.1.4.1.3902.1015.2.1.7.3 | NodezxAnFanExMgmt | |||
| 1.3.6.1.4.1.3902.1015.2.1.7.3.1 | TablezxAnFanExMgmtTable | not-accessible | current | This table includes speed information and operational status of the fan. |
| 1.3.6.1.4.1.3902.1015.2.1.7.3.1.1 | RowzxAnFanExMgmtEntry | not-accessible | current | The entry of zxAnFanExMgmtTable. |
| 1.3.6.1.4.1.3902.1015.2.1.7.3.1.1.1 | ColumnzxAnFanExIndex | not-accessible | current | The index of this fan. |
| 1.3.6.1.4.1.3902.1015.2.1.7.3.1.1.2 | ColumnzxAnFanExConfSpeedLevel | read-create | current | The configured speed level of the fan. NOTE: No recomanded to display it in NMS. |
| 1.3.6.1.4.1.3902.1015.2.1.7.3.1.1.3 | ColumnzxAnFanExActualSpeedLevel | read-only | current | The actual speed level of the fan. |
| 1.3.6.1.4.1.3902.1015.2.1.7.3.1.1.4 | ColumnzxAnFanExAdminStatus | read-create | current | The administrative status of the fan. NOTE: No recomanded to configure it in NMS. |
| 1.3.6.1.4.1.3902.1015.2.1.7.3.1.1.5 | ColumnzxAnFanExOperStatus | read-only | current | The operational status of the fan. |
| 1.3.6.1.4.1.3902.1015.2.1.7.3.1.1.6 | ColumnzxAnFanExOnlineStatus | read-only | current | The actual online status of the fan. |
| 1.3.6.1.4.1.3902.1015.2.1.7.3.1.1.7 | ColumnzxAnFanExActualSpeed | read-only | current | The actual speed of the fan. NOTE: If not supported, NMS should use the speed value of zxAnFanExActualSpeedLevel |
| 1.3.6.1.4.1.3902.1015.2.1.8 | NodezxAnEquipMonitorObjects | |||
| 1.3.6.1.4.1.3902.1015.2.1.8.2 | TablezxAnCardWatchdogTable | not-accessible | current | Watchdog function table. |
| 1.3.6.1.4.1.3902.1015.2.1.8.2.1 | RowzxAnCardWatchdogEntry | not-accessible | current | Watchdog function entry. |
| 1.3.6.1.4.1.3902.1015.2.1.8.2.1.1 | ColumnzxAnCardHardwareWatchdogEnable | read-write | current | Enables or disables the card reset when cpu is hanged. |
| 1.3.6.1.4.1.3902.1015.2.1.8.2.1.2 | ColumnzxAnCardTaskSuspendCardResetMode | read-write | current | Card reset mode when task suspended. notReset(1) allTask(2) criticalTask(3) |
| 1.3.6.1.4.1.3902.1015.2.1.8.2.1.3 | ColumnzxAnCardSoftwareWatchdogEnable | read-write | current | Enables or disables the card reset when the task duration exceed zxAnCardTaskDurationThreshold and the task CPU usage exceed zxAnCardTaskCpuUsageThreshold. Whe… |
| 1.3.6.1.4.1.3902.1015.2.1.8.2.1.4 | ColumnzxAnCardTaskDurationThreshold | read-write | current | Task duration threshold. |
| 1.3.6.1.4.1.3902.1015.2.1.8.2.1.5 | ColumnzxAnCardTaskCpuUsageThreshold | read-write | current | Task CPU usage threshold. |
| 1.3.6.1.4.1.3902.1015.2.2 | NodezxAnEquipTrapObjects | |||
| 1.3.6.1.4.1.3902.1015.2.2.1 | NodezxAnEquipSysTrapGroup | |||
| 1.3.6.1.4.1.3902.1015.2.2.1.2 | NotificationzxAnEquipCtrlCardSwapped | current | A zxAnEquipCtrlCardSwapped trap indicates that the main control card has swapped to slave card. | |
| 1.3.6.1.4.1.3902.1015.2.2.1.3 | NotificationzxAnEquipBackupSynchFailed | current | A zxAnEquipBackupSynchFailed trap indicates that the data synchronization between main control card and standby card has failed. | |
| 1.3.6.1.4.1.3902.1015.2.2.1.6 | NotificationzxAnEquipCtrlCardSwapCleared | current | A zxAnEquipCtrlCardSwapCleared trap indicates that the main control card swapped trap has cleared. | |
| 1.3.6.1.4.1.3902.1015.2.2.2 | NodezxAnEquipCardTrapGroup | |||
| 1.3.6.1.4.1.3902.1015.2.2.2.1 | NotificationzxAnEquipCardUp | current | It indicates that the agent has detected that the card has been online and come into inService status. | |
| 1.3.6.1.4.1.3902.1015.2.2.2.2 | NotificationzxAnEquipCardDown | current | It indicates that the agent has detected that the card has been offline or not work well again when it is running. NOTES: zxAnCardInvSn is not used here.It can… | |
| 1.3.6.1.4.1.3902.1015.2.2.2.3 | NotificationzxAnEquipCardDetectFailed | current | It indicates that the agent has detected that the card scanning of a card has process error. | |
| 1.3.6.1.4.1.3902.1015.2.2.2.4 | NotificationzxAnEquipCardDetectSuccess | current | It indicates that the agent has detected that the card scanning error has process cleared. | |
| 1.3.6.1.4.1.3902.1015.2.2.2.6 | NotificationzxAnEquipCardCpuLoadAlarm | current | It indicates that the agent has detected that the zxAnEquipCardCPULoad object of one card has exceeded the configured threshhold value of zxAnCardCpuLoadThresh… | |
| 1.3.6.1.4.1.3902.1015.2.2.2.7 | NotificationzxAnEquipCardCpuLoadAlarmCleard | current | It indicates that the agent has detected that the zxAnEquipCardCPULoad object of one card has less than the configured threshhold value of zxAnCardCpuLoadThres… | |
| 1.3.6.1.4.1.3902.1015.2.2.2.8 | NotificationzxAnEquipCardMemoryOverLoad | current | It indicates that the agent has detected that the zxAnEquipCardMemUsage object of one card has exceeded the configured threshhold value of zxAnCardMemUsageThre… | |
| 1.3.6.1.4.1.3902.1015.2.2.2.9 | NotificationzxAnEquipCardMemoryAlarmCleard | current | It indicates that the agent has detected that the zxAnEquipCardMemUsage object of one card has less than the configured threshhold value of zxAnCardMemUsageThr… | |
| 1.3.6.1.4.1.3902.1015.2.2.2.10 | NotificationzxAnEquipCardUpdateVersionFailed | current | It indicates that the Card has failed to update version. | |
| 1.3.6.1.4.1.3902.1015.2.2.2.11 | NotificationzxAnEquipCardUpdateVerSuccess | current | It indicates that the Card has been success to update version. NOTE: The variable zxAnSwManualFailedReason is only used by agent and it will not be used by man… | |
| 1.3.6.1.4.1.3902.1015.2.2.2.12 | NotificationzxAnEquipCardSvcCommFailed | current | It indicates that the agent has detected that the service communication of a card has occurred. NOTE: It is supported by MSAG5200 ONLY now. 2008-1-8 | |
| 1.3.6.1.4.1.3902.1015.2.2.2.13 | NotificationzxAnEquipCardSvcCommSuccess | current | It indicates that the agent has detected that the service communication error of a card has cleared. NOTE: It is supported by MSAG5200 ONLY now. 2008-1-8 | |
| 1.3.6.1.4.1.3902.1015.2.2.2.14 | NotificationzxAnEquipCardCpldInvalid | current | It indicates that the CPLD is invalid due to update failure. | |
| 1.3.6.1.4.1.3902.1015.2.2.2.15 | NotificationzxAnEquipCardSwNotRunning | current | A zxAnEquipCardSwNotRunning trap is sent when the agent has detected that the card has plugged in and configured, but software is not running and zxAnCardOperS… | |
| 1.3.6.1.4.1.3902.1015.2.2.2.16 | NotificationzxAnEquipCardSwNotRunningRestore | current | A zxAnEquipCardSwNotRunningRestore trap is sent when the agent has detected that the card is inservice. | |
| 1.3.6.1.4.1.3902.1015.2.2.2.17 | NotificationzxAnEquipCardOffline | current | A zxAnEquipCardOffline trap is sent when the agent has detected that the configured card has plugged out. | |
| 1.3.6.1.4.1.3902.1015.2.2.2.18 | NotificationzxAnEquipCardOnline | current | A zxAnEquipCardOnline trap is sent when the agent has detected that the configured card has plugged in. | |
| 1.3.6.1.4.1.3902.1015.2.2.2.19 | NotificationzxAnEquipCardTypeMismatch | current | A zxAnEquipCardTypeMismatch trap is sent when the agent has detected that the card has plugged in ,but zxAnCardConfMainType is not same as zxAnCardActType. | |
| 1.3.6.1.4.1.3902.1015.2.2.2.20 | NotificationzxAnEquipCardTypeMismatchRestore | current | A zxAnEquipCardTypeMismatchRestore trap is sent when the agent has detected that the card has plugged in and zxAnCardConfMainType is same as zxAnCardActType. | |
| 1.3.6.1.4.1.3902.1015.2.2.2.21 | NotificationzxAnEquipCardNotConfigured | current | A zxAnEquipCardNotConfigured trap is sent when the agent has detected that the card has plugged in but not configured. | |
| 1.3.6.1.4.1.3902.1015.2.2.2.22 | NotificationzxAnEquipCardConfigured | current | A zxAnEquipCardConfigured trap is sent when the agent has detected that the card has plugged in and configured. | |
| 1.3.6.1.4.1.3902.1015.2.2.2.23 | NotificationzxAnEquipCardNotSupportedAlm | current | A zxAnEquipCardNotSupportedAlm trap is sent when the agent has detected that the card plugged in is not supported. | |
| 1.3.6.1.4.1.3902.1015.2.2.2.24 | NotificationzxAnEquipCardNotSupportedClr | current | A zxAnEquipCardNotSupportedClr trap is sent when the agent has detected that the card which not supported is pulled out. | |
| 1.3.6.1.4.1.3902.1015.2.2.2.30 | NotificationzxAnEquipSubCardUp | current | It indicates that the agent has detected that the subcard has been online and come into inService status. | |
| 1.3.6.1.4.1.3902.1015.2.2.2.31 | NotificationzxAnEquipSubCardDown | current | It indicates that the agent has detected that the subcard has been offline or not work well when it is running. | |
| 1.3.6.1.4.1.3902.1015.2.2.2.32 | NotificationzxAnEquipSubcardCpldInvalid | current | It indicates that the CPLD is invalid due to update failure. | |
| 1.3.6.1.4.1.3902.1015.2.2.2.33 | NotificationzxAnPowerSupplyCardHardwareFault | current | It indicates that the agent has detected that the power supply card hardware fault happened. | |
| 1.3.6.1.4.1.3902.1015.2.2.3 | NodezxAnEquipEnvTrapGroup | |||
| 1.3.6.1.4.1.3902.1015.2.2.3.1 | NotificationzxAnEnvTempExceededTrap | current | The temperature inside the chassis has exceeded normal operating temperature zxAnEnvTemperatureAlarmThreshold. The zxAnEnvTemperature object identifies the cur… | |
| 1.3.6.1.4.1.3902.1015.2.2.3.2 | NotificationzxAnEnvTempNormalTrap | current | The temperature inside the chassis has returned to normal operating temperature zxAnEnvTemperatureAlarmThreshold. The zxAnEnvTemperature object identifies the … | |
| 1.3.6.1.4.1.3902.1015.2.2.3.3 | NotificationzxAnEnvMonitorInterfaceLinkDown | current | It indicates that the agent has detected that the link at the enviroment monitoring inerface has been down. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.4 | NotificationzxAnEnvMonitorInterfaceLinkUp | current | It indicates that the agent has detected that the link at the enviroment monitoring inerface has been up. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.5 | NotificationzxAnEnvFanLinkDown | current | It indicates that the agent has detected that fan is offline. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.6 | NotificationzxAnEnvFanLinkUp | current | It indicates that the agent has detected that fan is online. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.7 | NotificationzxAnEnvTemperatureSensorFault | current | It indicates that the temperature sensor is in fault. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.8 | NotificationzxAnEnvFanFault | current | It indicates that the fan is in fault. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.9 | NotificationzxAnEnvFanFaultCleard | current | It indicates that the fan's fault is cleared. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.10 | NotificationzxAnEnvDustCapDown | current | It indicates that the dust cap is up. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.11 | NotificationzxAnEnvDustCapUp | current | It indicates that the dust cap is down. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.12 | NotificationzxAnEnvPowerSupplyDwon | current | It indicates that the power supply module is down. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.13 | NotificationzxAnEnvPowerSupplyUp | current | It indicates that the power supply module is up. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.14 | NotificationzxAnEnvMPTempExceededTrap | current | The temperature inside the MP has exceeded normal operating temperature zxAnMPTemperatureAlarmThreshold. The zxAnEnvTemperature object identifies the current s… | |
| 1.3.6.1.4.1.3902.1015.2.2.3.15 | NotificationzxAnEnvMPTempNormalTrap | current | The temperature inside the MP has returned to normal operating temperature zxAnMPTemperatureAlarmThreshold. The zxAnEnvTemperature object identifies the curren… | |
| 1.3.6.1.4.1.3902.1015.2.2.3.16 | NotificationzxAnEnvFanInterfaceLinkDown | current | It indicates that the agent has detected that the link at the fan card inerface has been down. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.17 | NotificationzxAnEnvFanInterfaceLinkUp | current | It indicates that the agent has detected that the link at the fan card inerface has been up. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.18 | NotificationzxAnEnvPowerOverVoltage | current | It indicates that the input voltage of power supply is over-voltage. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.19 | NotificationzxAnEnvPowerOverVoltageCleard | current | It indicates that the over-voltage fault is cleared. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.20 | NotificationzxAnEnvPowerUnderVoltage | current | It indicates that the input voltage of power supply is under-voltage. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.21 | NotificationzxAnEnvPowerUnderVoltageCleard | current | It indicates that the under-voltage fault is cleared. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.22 | NotificationzxAnEnvPowerOff | current | It indicates that the power supply is off. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.23 | NotificationzxAnEnvPowerUp | current | It indicates that the power supply off fault is cleared. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.24 | NotificationzxAnEnvCardOverTemperature | current | The card temperature inside the chassis has exceeded normal operating temperature zxAnMPTemperatureAlarmThreshold. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.25 | NotificationzxAnEnvCardOverTemperatureCleard | current | It indicates that card over-temperature fault is cleared. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.26 | NotificationzxAnEnvLowerFanBoardLinkDown | current | The Lower Fan Board Link Down. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.27 | NotificationzxAnEnvLowerFanBoardLinkUp | current | It indicates that the Lower Fan Board link up. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.28 | NotificationzxAnEnvAcMainsPowerOff | current | AC mains power off. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.29 | NotificationzxAnEnvAcMainsPowerOn | current | AC mains power on. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.30 | NotificationzxAnEnvGponCardsShutdown | current | A zxAnEnvGponCardsShutdown trap is sent when the agent has detected that the MP temperature is above threshold. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.31 | NotificationzxAnEnvGponCardsStartup | current | A zxAnEnvGponCardsStartup trap is sent when the agent has detected that the MP temperature is below threshold. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.32 | NotificationzxAnEnvCardHighTempShutdownAlm | current | A zxAnEnvCardHighTempShutdownAlm trap is sent when the agent has detected that the card temperature is above threshold. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.33 | NotificationzxAnEnvCardHighTempShutdownClr | current | A zxAnEnvCardHighTempShutdownClr trap is sent when the card is been powered on. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.34 | NotificationzxAnEnvBroadbandOverheatHaltAlm | current | A zxAnEnvBroadbandOverheatHaltAlm trap is sent when the agent has detected that the NE temperature is above zxAnEnvOverheatTmpThreshold. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.35 | NotificationzxAnEnvBroadbandOverheatHaltClr | current | A zxAnEnvBroadbandOverheatHaltClr trap is sent when the NE temperature is normal. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.36 | NotificationzxAnBatteryEnergySavingBbHaltAlm | current | A zxAnBatteryEnergySavingBbHaltAlm trap is sent when the power supply is battery which energy saving has been enabled. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.37 | NotificationzxAnBatteryEnergySavingBbHaltClr | current | A zxAnBatteryEnergySavingBbHaltClr trap is sent when the power supply is AC mains or the battery energy saving has been disabled. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.38 | NotificationzxAnEnvDeviceAbnormalAlm | current | A zxAnEnvDeviceAbnormalAlm trap is sent when the current status of environment device is inconsistent with normal status. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.39 | NotificationzxAnEnvDeviceAbnormalClr | current | A zxAnEnvDeviceAbnormalClr trap is sent when current status of environment device is consistent with normal status. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.40 | NotificationzxAnEnvNoBatteryAlm | current | A zxAnEnvNoBatteryAlm trap is sent when no battery found by the agent. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.41 | NotificationzxAnEnvNoBatteryClr | current | A zxAnEnvNoBatteryClr trap is sent when the battery has been found by the agent. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.42 | NotificationzxAnEnvBatteryUnderVoltageAlm | current | A zxAnEnvBatteryUnderVoltageAlm trap is sent when the battery voltage is under-voltage. | |
| 1.3.6.1.4.1.3902.1015.2.2.3.43 | NotificationzxAnEnvBatteryUnderVoltageClr | current | A zxAnEnvBatteryUnderVoltageClr trap is sent when the battery voltage becomes normal. | |
| 1.3.6.1.4.1.3902.1015.2.2.4 | NodezxAnEquipEnvExTrapGroup | |||
| 1.3.6.1.4.1.3902.1015.2.2.4.1 | NotificationzxAnEnvExTempExceededTrap | current | The temperature inside the chassis has exceeded normal operating temperature zxAnEnvExTempAlarmThreshold. The zxAnEnvExTemperature object identifies the curren… | |
| 1.3.6.1.4.1.3902.1015.2.2.4.2 | NotificationzxAnEnvExTempNormalTrap | current | The temperature inside the chassis has returned to normal operating temperature zxAnEnvExTempAlarmThreshold. The zxAnEnvExTemperature object identifies the cur… | |
| 1.3.6.1.4.1.3902.1015.2.2.4.3 | NotificationzxAnEnvExFanInterfaceLinkDown | current | It indicates that the agent has detected that the link at the fan card inerface has been down. | |
| 1.3.6.1.4.1.3902.1015.2.2.4.4 | NotificationzxAnEnvExFanInterfaceLinkUp | current | It indicates that the agent has detected that the link at the fan card inerface has been up. | |
| 1.3.6.1.4.1.3902.1015.2.2.4.5 | NotificationzxAnEnvExFanFault | current | It indicates that the fan is in fault. | |
| 1.3.6.1.4.1.3902.1015.2.2.4.6 | NotificationzxAnEnvExFanFaultCleard | current | It indicates that the fan's fault is cleared. | |
| 1.3.6.1.4.1.3902.1015.2.3 | NodezxAnEquipGlobalObjects | |||
| 1.3.6.1.4.1.3902.1015.2.3.1 | ScalarzxAnEquipCapabilities | read-only | current | The equipment management capabilities of this equipment. The bit value 1 means the function represented by this bit is supported by this equipment. bit 1: valu… |