ZTE-AN-LDP-MIB
49 objects
This MIB contains managed object definitions for LDP operation.
Imported Objects
| INET-ADDRESS-MIB | InetAddress InetAddressType |
| SNMPv2-SMI | Counter64 experimental Integer32 IpAddress MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE TimeTicks Unsigned32 |
| SNMPv2-TC | DisplayString RowStatus |
| ZTE-AN-L3-IF-MIB | zxAnL3IfIndex |
| ZTE-AN-TC-MIB | zxAn |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.3902.1015.55 | IdentityzxAnLdpMib | This MIB contains managed object definitions for LDP operation. | ||
| 1.3.6.1.4.1.3902.1015.55.1 | NodezxAnLdpGlobalObjects | |||
| 1.3.6.1.4.1.3902.1015.55.1.1 | ScalarzxAnLdpMplsEnable | read-write | current | Enable MPLS service. |
| 1.3.6.1.4.1.3902.1015.55.1.2 | ScalarzxAnLdpMplsMinLabel | read-write | current | Minimum value in dynamic label range of MPLS. For OLT C300, the label value range from 16 to 1044478. |
| 1.3.6.1.4.1.3902.1015.55.1.3 | ScalarzxAnLdpMplsMaxLabel | read-write | current | Maximum value in dynamic label range of MPLS. For OLT C300, the label value range from 16 to 1044478, and the default maximum value is 1044478. |
| 1.3.6.1.4.1.3902.1015.55.1.4 | ScalarzxAnLdpMplsLdpRouterId | read-write | current | A zxAnL3IfIndex is used as the LDP router ID. It is recommended to use loopback interface as LDP router ID. L3 VLAN interface also can be configed. IP address … |
| 1.3.6.1.4.1.3902.1015.55.1.5 | ScalarzxAnLdpMplsLdpRouterIdForce | read-write | current | zxAnLdpMplsLdpRouterId is valid immediately. When force is set whether the router ID designated takes effect depends on the current status of the designated in… |
| 1.3.6.1.4.1.3902.1015.55.1.6 | ScalarzxAnLdpMplsExplicitNullEnable | read-write | current | MPLS explicit null label enable switch. |
| 1.3.6.1.4.1.3902.1015.55.1.7 | ScalarzxAnLdpMplsMinInUseLabel | read-only | current | Minimum value in dynamic label range of MPLS in use. For OLT C300, the label value ranges from 16 to 1044478. |
| 1.3.6.1.4.1.3902.1015.55.1.8 | ScalarzxAnLdpMplsMaxInUseLabel | read-only | current | Maximum value in dynamic label range of MPLS in use. For OLT C300, the label value ranges from 16 to 1044478. |
| 1.3.6.1.4.1.3902.1015.55.1.9 | ScalarzxAnLdpMplsSessInitBackoffTime | read-write | current | The initial time which LDP entity should wait and try again after LDP failed to establish a session. |
| 1.3.6.1.4.1.3902.1015.55.1.10 | ScalarzxAnLdpMplsSessMaxBackoffTime | read-write | current | The maximum time which LDP entity could use to rebuild session after LDP failed to establish a session. The waiting time starts from the initial back off time,… |
| 1.3.6.1.4.1.3902.1015.55.1.11 | ScalarzxAnLdpMplsSessKeepAliveTime | read-write | current | The timer which is the proposed keep alive hold timer for LDP session. |
| 1.3.6.1.4.1.3902.1015.55.1.12 | ScalarzxAnLdpMplsGrEnable | read-write | current | LDP GR(Graceful Restart) function enable switch. It indicates whether LDP GR function should be enabled. |
| 1.3.6.1.4.1.3902.1015.55.1.13 | ScalarzxAnLdpMplsGrRecoveryTime | read-write | current | The maximum time which is the proposed GR recovery timer for this LDP entity. After LDP session rebuilt, GR Helper assists GR Restarter to update label forward… |
| 1.3.6.1.4.1.3902.1015.55.1.14 | ScalarzxAnLdpMplsGrNeighKeepAliveTime | read-write | current | The maximum time which is the proposed keep alive neighbor when a LDP entity found the peer is down. |
| 1.3.6.1.4.1.3902.1015.55.1.15 | ScalarzxAnLdpMplsVpnGrEnable | read-write | current | MPLS Layer 2 VPN GR function enable switch. |
| 1.3.6.1.4.1.3902.1015.55.1.16 | ScalarzxAnLdpMplsHelloHoldTime | read-write | current | The timer which is the proposed Hello hold timer for this LDP entity. A value of 65535 means infinite. |
| 1.3.6.1.4.1.3902.1015.55.1.17 | ScalarzxAnLdpMplsHelloSendInterval | read-write | current | The time interval to send Hello message for this LDP entity. The time must be smaller than the hello hold time. |
| 1.3.6.1.4.1.3902.1015.55.1.18 | ScalarzxAnLdpMplsTgtHelloHoldTime | read-write | current | The timer which is the proposed targeted Hello hold timer for this LDP entity. A value of 65535 means infinite. |
| 1.3.6.1.4.1.3902.1015.55.1.19 | ScalarzxAnLdpMplsTgtHelloSendInterval | read-write | current | The time interval to send targeted Hello message for this LDP entity. The time must be smaller than the targeted hello hold time. |
| 1.3.6.1.4.1.3902.1015.55.1.20 | ScalarzxAnLdpMplsKeepSessWithHelloMsg | read-write | current | LDP session keeping alive with hello messages enable switch. If the switch is enabling, the LDP session reset keep alive timer when receiving a hello message. |
| 1.3.6.1.4.1.3902.1015.55.1.21 | ScalarzxAnLdpMplsGrHelperEnable | read-write | current | Graceful restart helper enable switch. |
| 1.3.6.1.4.1.3902.1015.55.1.22 | ScalarzxAnLdpMplsLabelControlMode | read-write | current | To specify control mode of LSP. |
| 1.3.6.1.4.1.3902.1015.55.1.23 | ScalarzxAnLdpMplsLabelRetentionMode | read-write | current | To specify retention mode of LSP. |
| 1.3.6.1.4.1.3902.1015.55.1.24 | ScalarzxAnLdpMplsPktWithLabelEnable | read-write | current | To specify label encapsulation mode when LSR sending protocol packets. |
| 1.3.6.1.4.1.3902.1015.55.2 | NodezxAnLdpObjects | |||
| 1.3.6.1.4.1.3902.1015.55.2.3 | TablezxAnLdpTargetSessionTable | not-accessible | current | This table contains information about the MPLS target session. |
| 1.3.6.1.4.1.3902.1015.55.2.3.1 | RowzxAnLdpTargetSessionEntry | not-accessible | current | An entry in this table represents an LDP target session. |
| 1.3.6.1.4.1.3902.1015.55.2.3.1.1 | ColumnzxAnLdpTargetIpAddrType | not-accessible | current | The type of the zxAnLdpTargetIpAddr, as defined in the InetAddress MIB. |
| 1.3.6.1.4.1.3902.1015.55.2.3.1.2 | ColumnzxAnLdpTargetIpAddr | not-accessible | current | Peer address of target LDP session. |
| 1.3.6.1.4.1.3902.1015.55.2.3.1.3 | ColumnzxAnLdpTargetDistributionMode | read-create | current | The label distribution mode. |
| 1.3.6.1.4.1.3902.1015.55.2.3.1.20 | ColumnzxAnLdpTargetSessionRowStatus | read-create | current | Row Status of the table. |
| 1.3.6.1.4.1.3902.1015.55.2.4 | TablezxAnLdpSessionTable | not-accessible | current | LDP session table. This table contains information about LDP session. |
| 1.3.6.1.4.1.3902.1015.55.2.4.1 | RowzxAnLdpSessionEntry | not-accessible | current | Entry contains LDP information. |
| 1.3.6.1.4.1.3902.1015.55.2.4.1.1 | ColumnzxAnLdpPeerIpAddrType | not-accessible | current | The type of the zxAnLdpPeerIpAddr, as defined in the InetAddress MIB. |
| 1.3.6.1.4.1.3902.1015.55.2.4.1.2 | ColumnzxAnLdpPeerIpAddr | not-accessible | current | The IP address of peer. |
| 1.3.6.1.4.1.3902.1015.55.2.4.1.3 | ColumnzxAnLdpMd5Pwd | read-create | current | Password used for communication between LSRs. |
| 1.3.6.1.4.1.3902.1015.55.2.4.1.4 | ColumnzxAnLdpMd5PwdConfStatus | read-only | current | The status indicates whether the MD5 is registered. |
| 1.3.6.1.4.1.3902.1015.55.2.4.1.5 | ColumnzxAnLdpMd5PwdEncrypt | read-create | current | The status indicates whether the MD5 password is encrypted. When the password is encrypted, the password cannot be read. |
| 1.3.6.1.4.1.3902.1015.55.2.4.1.6 | ColumnzxAnLdpSessionReset | read-write | current | Used to reset the LDP session. |
| 1.3.6.1.4.1.3902.1015.55.2.4.1.20 | ColumnzxAnLdpSessionRowStatus | read-create | current | Row Status of the table. |
| 1.3.6.1.4.1.3902.1015.55.2.5 | TablezxAnLdpL3IfEntityTable | not-accessible | current | This table contains information about the MPLS Label Distribution Protocol Entities which exist on this L3 VLAN interface. |
| 1.3.6.1.4.1.3902.1015.55.2.5.1 | RowzxAnLdpL3IfEntityEntry | not-accessible | current | Entry contains information of the LDP Entity. |
| 1.3.6.1.4.1.3902.1015.55.2.5.1.1 | ColumnzxAnLdpL3IfTransAddrMode | read-create | current | Change the transport address configuration of LDP. |
| 1.3.6.1.4.1.3902.1015.55.2.5.1.2 | ColumnzxAnLdpL3IfTransAddrType | read-create | current | The type of the zxAnLdpTransAddr, as defined in the InetAddress MIB. |
| 1.3.6.1.4.1.3902.1015.55.2.5.1.3 | ColumnzxAnLdpL3IfTransAddr | read-create | current | Address of transport. |
| 1.3.6.1.4.1.3902.1015.55.2.5.1.4 | ColumnzxAnLdpL3IfDistributionMode | read-create | current | The label distribution mode. |
| 1.3.6.1.4.1.3902.1015.55.2.5.1.20 | ColumnzxAnLdpL3IfEntityRowStatus | read-create | current | Row Status of the Table. |