ACC-DS1
28 objects
No module-level DESCRIPTION found.
Imported Objects
| ACC-MIB | accBRG DisplayString IfIndex RowStatus SmdsAddress |
| ACC-SYSTEM | accTrapLogSeqNum |
| RFC1155-SMI | OBJECT-TYPE |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.5.1.1.42 | TableaccDs1ExtTable | not-accessible | mandatory | The DS1 extension table. |
| 1.3.6.1.4.1.5.1.1.42.1 | RowaccDs1ExtEntry | not-accessible | mandatory | An entry in the DS1 extension table. |
| 1.3.6.1.4.1.5.1.1.42.1.1 | ColumnaccDs1ExtLineIndex | read-only | mandatory | This object is the identifier of a DS1 Interface on a managed device. It has the same value as dsx1LineIndex. |
| 1.3.6.1.4.1.5.1.1.42.1.2 | ColumnaccDs1ExtLineLength | read-write | mandatory | The approximate line length. When equipped with a DSX1 line interface module, this object selects the transmit equalization. When equipped with a CSU interface… |
| 1.3.6.1.4.1.5.1.1.42.1.3 | ColumnaccDS1ExtNfasGroup | read-write | mandatory | The ifIndex of another DS1 interface whose common signaling channel (e.g., ISDN D channel) carries signaling information for this DS1 interface. |
| 1.3.6.1.4.1.5.1.1.42.1.4 | ColumnaccDs1ExtInterfaceId | read-write | mandatory | The internal interface on which signalling is received. 0 indicates the D-channel. |
| 1.3.6.1.4.1.5.1.1.42.1.5 | ColumnaccDs1ExtE1Type | read-write | mandatory | The type of E1 equipment to which the device is connected. Only used to work around Nordic type switch anomolies. |
| 1.3.6.1.4.1.5.1.1.42.1.6 | ColumnaccDs1ExtXcvr | read-write | mandatory | The type of transceiver installed. |
| 1.3.6.1.4.1.5.1.1.42.1.7 | ColumnaccDs1ExtPrecedence | read-write | mandatory | When the interface is provisioned as a PRI interface with D-channel backup, this object determines whether the D channel on this interface is the primary or se… |
| 1.3.6.1.4.1.5.1.1.42.1.8 | ColumnaccDs1ExtSignalGroup | read-write | mandatory | The index of the Signal group assigned to this interface. The value of the trunk group index is limited to the maximum number of PRI interfaces that can be ins… |
| 1.3.6.1.4.1.5.1.1.42.1.9 | ColumnaccDs1ExtNumberGroup | read-write | mandatory | The index of the called number group assigned to this interface. Number groups are defined in the Called Number Table. A number group value of 0 indicates that… |
| 1.3.6.1.4.1.5.1.1.42.1.10 | ColumnaccDs1ExtIntegAccess | read-write | mandatory | Indicates whether this interface has enabled integrated access. If enabled, the signal group is used as the signaling channel for this interface. |
| 1.3.6.1.4.1.5.1.1.42.1.11 | ColumnaccDs1ExtSignalMode | read-write | mandatory | Signaling mode for this DS1 interface |
| 1.3.6.1.4.1.5.1.1.42.1.12 | ColumnaccDs1ExtCICBase | read-write | mandatory | CIC base to use for circuits on this DS1 interface. |
| 1.3.6.1.4.1.5.1.1.42.1.13 | ColumnaccDs1ExtMessageLevel | read-write | mandatory | Maintenance message level for this DS1 interface. |
| 1.3.6.1.4.1.5.1.1.42.1.14 | ColumnaccDs1ExtServiceState | read-only | mandatory | Describes DS1 service state. Certain attributes need to be in a specific state to be changed. |
| 1.3.6.1.4.1.5.1.1.43 | TableaccDs1CircuitTable | not-accessible | mandatory | The DS1 circuit configuration table. |
| 1.3.6.1.4.1.5.1.1.43.1 | RowaccDs1CircuitEntry | not-accessible | mandatory | An entry in the DS1 circuit configuration table. |
| 1.3.6.1.4.1.5.1.1.43.1.1 | ColumnaccDs1CircuitIndex | read-only | mandatory | This object is the identifier of a circuit on a managed DS1 interface. It should have the same value as ifIndex. |
| 1.3.6.1.4.1.5.1.1.43.1.2 | ColumnaccDs1CircuitAdi | read-write | mandatory | Enables or disables alternate digit inversion for a circuit on a managed DS1 interface. This object applies only to E1 interfaces. |
| 1.3.6.1.4.1.5.1.1.43.1.3 | ColumnaccDs1CircuitBandwidth | read-write | mandatory | The bandwidth of the circuit in kilobits per second. |
| 1.3.6.1.4.1.5.1.1.43.1.4 | ColumnaccDs1CircuitBusyout | read-write | mandatory | The busyout status of a circuit. If the status is set to busy, the circuit is taken out of service and is unable to carry user data. |
| 1.3.6.1.4.1.5.1.1.43.1.5 | ColumnaccDs1CircuitInversion | read-write | mandatory | Enables or disables circuit inversion for a circuit on a managed DS1 interface. This object applies only to T1 interfaces. |
| 1.3.6.1.4.1.5.1.1.43.1.6 | ColumnaccDs1CircuitName | read-write | mandatory | This object is used to associate a name with a particular DS1 circuit. |
| 1.3.6.1.4.1.5.1.1.43.1.7 | ColumnaccDs1CircuitConfigStatus | read-write | mandatory | This object gives the configuration status for a circuit entry, and may have the following values: UNCONFIG The circuit has not been configured or has been del… |
| 1.3.6.1.4.1.5.1.1.43.1.8 | ColumnaccDs1CircuitLoopback | read-write | mandatory | This object represents the loopback status of the DS1 circuit. Any active loopback can be removed by setting the loopback status to none. |
| 1.3.6.1.4.1.5.1.1.43.1.9 | ColumnaccDs1CircuitRbs | read-write | mandatory | Enables or disables robbed bit signaling for a circuit on a managed DS1 interface. This object applies only to T1 interfaces. |
| 1.3.6.1.4.1.5.1.1.43.1.10 | ColumnaccDs1CircuitSuperrateMask | read-write | mandatory | Specifies the time-slots used by a superrate circuit. Each bit which is set corresponds to a time-slot which is allocated to the superrate circuit. 2**n-1 corr… |