ACC-FR
69 objects
No module-level DESCRIPTION found.
Imported Objects
| ACC-MIB | accBRG DisplayString IfIndex RowStatus SmdsAddress |
| ACC-SYSTEM | accTrapLogSeqNum |
| RFC1155-SMI | Counter IpAddress OBJECT-TYPE TimeTicks |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.5.1.1.20 | NodeaccFr | |||
| 1.3.6.1.4.1.5.1.1.20.1 | TableaccFrAtTable | not-accessible | mandatory | Internet address translation table for Frame Relay interfaces. Entries are added/deleted via management action. |
| 1.3.6.1.4.1.5.1.1.20.1.1 | RowaccFrAtEntry | not-accessible | mandatory | Internet address translation entry for Frame Relay interfaces. |
| 1.3.6.1.4.1.5.1.1.20.1.1.1 | ColumnaccFrAtIfIndex | read-write | mandatory | Interface number (ifIndex) for which this translation entry is valid. Object required in entry-adding SET PDU. |
| 1.3.6.1.4.1.5.1.1.20.1.1.2 | ColumnaccFrIpAddress | read-write | mandatory | IP Address Object required in entry-adding SET PDU. |
| 1.3.6.1.4.1.5.1.1.20.1.1.3 | ColumnaccFrDLCI | read-write | mandatory | Frame Relay DLCI to use for the specified host Object required in entry-adding SET PDU. |
| 1.3.6.1.4.1.5.1.1.20.1.1.4 | ColumnaccFrStatus | read-write | mandatory | Status of this entry Object required in entry-adding SET PDU. |
| 1.3.6.1.4.1.5.1.1.20.2 | TableaccFrStatTable | not-accessible | mandatory | Per-line statistics for Frame Relay interfaces |
| 1.3.6.1.4.1.5.1.1.20.2.1 | RowaccFrStatEntry | not-accessible | mandatory | Frame Relay statistics |
| 1.3.6.1.4.1.5.1.1.20.2.1.1 | ColumnaccFrIndex | read-only | mandatory | Physical Port number of this Frame Relay interface. |
| 1.3.6.1.4.1.5.1.1.20.2.1.2 | ColumnaccFrStatRcvDrops | read-only | mandatory | Number of received frames that were discarded due to lack of resources. |
| 1.3.6.1.4.1.5.1.1.20.2.1.3 | ColumnaccFrStatShorts | read-only | mandatory | Number of received frames that were discarded because they were too short (DLCI and/or protocol field missing). |
| 1.3.6.1.4.1.5.1.1.20.2.1.4 | ColumnaccFrStatIllDlcis | read-only | mandatory | Number of received frames that were discarded because the DLCI was badly formed. |
| 1.3.6.1.4.1.5.1.1.20.2.1.5 | ColumnaccFrStatUnkDlcis | read-only | mandatory | Number of received frames that were discarded because the DLCI did not match any configured value. |
| 1.3.6.1.4.1.5.1.1.20.2.1.6 | ColumnaccFrStatUnkProtos | read-only | mandatory | Number of received frames that were discarded because the protocol field did not match any protocol configured for the specified DLCI. |
| 1.3.6.1.4.1.5.1.1.20.2.1.7 | ColumnaccFrStatRsrvDlcis | read-only | mandatory | Number of received frames whose DLCI had the reserved bit set. (The frame was not discarded; the frame was processed as though the reserved bit were clear). |
| 1.3.6.1.4.1.5.1.1.20.2.1.8 | ColumnaccFrStatXmtDrops | read-only | mandatory | Number of frames that could not be transmitted due to lack of resources. |
| 1.3.6.1.4.1.5.1.1.20.2.1.9 | ColumnaccFrStatErrTime | read-only | mandatory | System uptime when the last Frame Relay error was detected. |
| 1.3.6.1.4.1.5.1.1.20.2.1.10 | ColumnaccFrStatErrType | read-only | mandatory | Type of last detected Frame Relay error. |
| 1.3.6.1.4.1.5.1.1.20.2.1.11 | ColumnaccFrStatErrDlci | read-only | mandatory | Value of DLCI field from last detected Frame Relay error (00 00 if no DLCI was associated with the last error). |
| 1.3.6.1.4.1.5.1.1.20.2.1.12 | ColumnaccFrStatErrProto | read-only | mandatory | Value of protocol field from last detected Frame Relay error (0 if no protocol field was associated with the last error). |
| 1.3.6.1.4.1.5.1.1.20.2.1.13 | ColumnaccFrLinkState | read-only | mandatory | State of this Frame Relay link |
| 1.3.6.1.4.1.5.1.1.20.2.1.14 | ColumnaccFrStatUnks | read-only | mandatory | Unused object |
| 1.3.6.1.4.1.5.1.1.20.2.1.15 | ColumnaccFrStatRcvLongs | read-only | mandatory | Number of received dlcmi frames longer than expected. |
| 1.3.6.1.4.1.5.1.1.20.2.1.16 | ColumnaccFrStatIlgDlcis | read-only | mandatory | Unused object |
| 1.3.6.1.4.1.5.1.1.20.2.1.17 | ColumnaccFrStatProtoErrs | read-only | mandatory | Number of received frames with a protocol violation. |
| 1.3.6.1.4.1.5.1.1.20.2.1.18 | ColumnaccFrStatUnkIes | read-only | mandatory | Number of dlcmi frames received with an unknown Information element. |
| 1.3.6.1.4.1.5.1.1.20.2.1.19 | ColumnaccFrStatSeqErrs | read-only | mandatory | Number of dlcmi frames received with a sequence error. |
| 1.3.6.1.4.1.5.1.1.20.2.1.20 | ColumnaccFrStatUnkRpts | read-only | mandatory | Unused object |
| 1.3.6.1.4.1.5.1.1.20.3 | TableaccFrParmTable | not-accessible | mandatory | Frame Relay parameter table |
| 1.3.6.1.4.1.5.1.1.20.3.1 | RowaccFrParmEntry | not-accessible | mandatory | Frame Relay parameter entry |
| 1.3.6.1.4.1.5.1.1.20.3.1.1 | ColumnaccFrParmIndex | read-only | mandatory | Interface number |
| 1.3.6.1.4.1.5.1.1.20.3.1.2 | ColumnaccFrParmAddrFmt | read-write | mandatory | Addressing format used. Q.921 per spec. Ignores length parameter draft-Q922 per March, 1990 draft of Q.922 q922 per October, 1990 Q.922 specification |
| 1.3.6.1.4.1.5.1.1.20.3.1.3 | ColumnaccFrParmAddrLen | read-write | mandatory | Length of address on serial line |
| 1.3.6.1.4.1.5.1.1.20.3.1.4 | ColumnaccFrParmEncap | read-write | mandatory | Type of encapsulation used on serial line |
| 1.3.6.1.4.1.5.1.1.20.3.1.5 | ColumnaccFrDlcmiState | read-write | mandatory | This variable states which Data Link Connection Management scheme is active (and by implication, what DLCI it uses) on the Frame Relay interface. |
| 1.3.6.1.4.1.5.1.1.20.3.1.6 | ColumnaccFrDlcmiPollInt | read-write | mandatory | the number of seconds between successive status enquiry messages. |
| 1.3.6.1.4.1.5.1.1.20.3.1.7 | ColumnaccFrDlcmiFullStatEnq | read-write | mandatory | Number of status enquiry intervals that pass before issuance of a full status enquiry message. |
| 1.3.6.1.4.1.5.1.1.20.3.1.8 | ColumnaccFrDlcmiErrThres | read-write | mandatory | Maximum number of unanswered Status Enquiries the equipmemt shall accept before declaring the interface down. |
| 1.3.6.1.4.1.5.1.1.20.3.1.9 | ColumnaccFrDlcmiMonEvents | read-write | mandatory | Maximum number of responses to FULL STATUS or LINK INTEGRITY VERIFICATION messages missed before the device will mark the interface down. |
| 1.3.6.1.4.1.5.1.1.20.3.1.10 | ColumnaccFrDlcmiType | read-write | mandatory | Link Maintenance is assymmetrical, so one end must be user, the other network. Normally the bridge/router is user. |
| 1.3.6.1.4.1.5.1.1.20.3.1.11 | ColumnaccFrDlcmiIdleTimer | read-write | mandatory | Number of minutes without receiving any non-dlcmi frames before declaring the link idle. Setting the timer to 0 will disable it. |
| 1.3.6.1.4.1.5.1.1.20.4 | TableaccFrCktTable | not-accessible | mandatory | Frame Relay circuit table |
| 1.3.6.1.4.1.5.1.1.20.4.1 | RowaccFrCktEntry | not-accessible | mandatory | Frame Relay circuit table entry |
| 1.3.6.1.4.1.5.1.1.20.4.1.1 | ColumnaccFrCktIfIndex | read-only | mandatory | Interface on which this circuit exists |
| 1.3.6.1.4.1.5.1.1.20.4.1.2 | ColumnaccFrCktDlci | read-only | mandatory | Data Link Connection Identifier for this circuit. |
| 1.3.6.1.4.1.5.1.1.20.4.1.3 | ColumnaccFrCktState | read-only | mandatory | Indicates whether the particular circuit is operational. |
| 1.3.6.1.4.1.5.1.1.20.4.1.4 | ColumnaccFrCktFECNrcvds | read-only | mandatory | Number of frames received from the network in- dicating forward congestion since the circuit was created. |
| 1.3.6.1.4.1.5.1.1.20.4.1.5 | ColumnaccFrCktBECNrcvds | read-only | mandatory | Number of frames received from the network in- dicating backward congestion since the circuit was created. |
| 1.3.6.1.4.1.5.1.1.20.4.1.6 | ColumnaccFrCktFrameXmts | read-only | mandatory | Number of frames sent from this circuit since it was created. |
| 1.3.6.1.4.1.5.1.1.20.4.1.7 | ColumnaccFrCktOctetXmts | read-only | mandatory | Number of octets sent from this circuit since it was created. |
| 1.3.6.1.4.1.5.1.1.20.4.1.8 | ColumnaccFrCktFrameRcvs | read-only | mandatory | Number of frames received by this circuit since it was created. |
| 1.3.6.1.4.1.5.1.1.20.4.1.9 | ColumnaccFrCktOctetRcvs | read-only | mandatory | Number of octets received by this circuit since it was created. |
| 1.3.6.1.4.1.5.1.1.20.4.1.10 | ColumnaccFrCktCreateTime | read-only | mandatory | The value of sysUpTime when the circuit was created. |
| 1.3.6.1.4.1.5.1.1.20.4.1.11 | ColumnaccFrCktChangeTime | read-only | mandatory | The value of sysUpTime when last there was a change in the circuit state. |
| 1.3.6.1.4.1.5.1.1.20.4.1.12 | ColumnaccFfrCktLoop | read-write | mandatory | Indicates the loopback state of the virtual circuit. The object is normally 'normal', indicating that the circuit is in its normal operational state. If set to… |
| 1.3.6.1.4.1.5.1.1.20.5 | TableaccFfrSwitchParameterTable | not-accessible | mandatory | Frame Relay Switch Parameter table |
| 1.3.6.1.4.1.5.1.1.20.5.1 | RowaccFfrSwitchParameterEntry | not-accessible | mandatory | An entry in Frame Relay Switch Parameter table |
| 1.3.6.1.4.1.5.1.1.20.5.1.1 | ColumnaccFfrSwitchIfindex1 | read-write | mandatory | The first interface index in the entry |
| 1.3.6.1.4.1.5.1.1.20.5.1.2 | ColumnaccFfrSwitchDlci1 | read-write | mandatory | The first Frame Relay DLCI in the entry |
| 1.3.6.1.4.1.5.1.1.20.5.1.3 | ColumnaccFfrSwitchIfindex2 | read-write | mandatory | The second interface index in the entry |
| 1.3.6.1.4.1.5.1.1.20.5.1.4 | ColumnaccFfrSwitchDlci2 | read-write | mandatory | The second Frame Relay DLCI in the entry |
| 1.3.6.1.4.1.5.1.1.20.5.1.5 | ColumnaccFfrSwitchStatus | read-write | mandatory | The Status tells whether the traffic will be switched as per the entry. This object also is usedin the delete command |
| 1.3.6.1.4.1.5.1.1.20.6 | TableaccVFRTable | not-accessible | mandatory | Table describing binding between a Virtual port and a Frame Relay DLCI and a physical port. Entries are added/deleted via management Action. |
| 1.3.6.1.4.1.5.1.1.20.6.1 | RowaccVFRTableEntry | not-accessible | mandatory | An entry in the Virtual Frame Relay DLCI Table. |
| 1.3.6.1.4.1.5.1.1.20.6.1.1 | ColumnaccVFRVirtualPort | read-write | mandatory | The virtual port to be associated with a Physical Port and DLCI. |
| 1.3.6.1.4.1.5.1.1.20.6.1.2 | ColumnaccVFRPhysicalPort | read-write | mandatory | The Physical Port to be associated with a virtual port and dlci. |
| 1.3.6.1.4.1.5.1.1.20.6.1.3 | ColumnaccVFRDlci | read-write | mandatory | The DLCI to be associated with a virtual and physical port. |
| 1.3.6.1.4.1.5.1.1.20.6.1.4 | ColumnaccVFRStatus | read-write | mandatory | The status field indicates if an add or delete is intended. Invalid = delete; Valid = add. |