MIB Viewer
 MIB Viewer Desktop New

CM-dot11plus-MIB

241 objects
This MIB defines additional 802.11 management objects not defined in the IEEE 802.11 MIB
Imported Objects
IF-MIBifIndex
INET-ADDRESS-MIB-- RFC 2863 InetAddressType InetAddress InetPortNumber
SNMPv2-SMICounter64 enterprises Integer32 IpAddress MODULE-IDENTITY OBJECT-TYPE Unsigned32
SNMPv2-TCDisplayString MacAddress PhysAddress RowStatus StorageType TruthValue
OIDNameAccessStatusDescription
1.3.6.1.4.1.1166Nodegi
1.3.6.1.4.1.1166.1Nodegiproducts
1.3.6.1.4.1.1166.1.19Nodecm
1.3.6.1.4.1.1166.1.19.51Identitycmdot11plusThis MIB defines additional 802.11 management objects not defined in the IEEE 802.11 MIB
1.3.6.1.4.1.1166.1.19.51.1Nodecmdot11plusObjects
1.3.6.1.4.1.1166.1.19.51.1.1Nodecmdot11plusMgmt
1.3.6.1.4.1.1166.1.19.51.1.1.1Nodecmdot11plusMgmtObjects
1.3.6.1.4.1.1166.1.19.51.1.1.1.1Scalarcmdot11plusWepModeread-writedeprecatedThe WEP encryption mode of 802.11 interface. This object is not writable and its return value should be ignored if cmdot11plusSecurityMode is not set to wep(2)…
1.3.6.1.4.1.1166.1.19.51.1.1.1.2Tablecmdot11plusWep128DefaultKeysTablenot-accessibledeprecatedTable containing 128-bit WEP parameters. This table shall contain the four WEP default secret 128-bit key values corresponding to the four possible values. The…
1.3.6.1.4.1.1166.1.19.51.1.1.1.2.1Rowcmdot11plusWep128DefaultKeysEntrynot-accessibledeprecatedWEP key table entry. Each entry contains a 128-bit WEP key This MIB object is only valid for products supporting a single SSID
1.3.6.1.4.1.1166.1.19.51.1.1.1.2.1.1Columncmdot11plusWep128Indexnot-accessibledeprecatedIdentifies instances of the columnar objects in the ACL table This MIB object is only valid for products supporting a single SSID
1.3.6.1.4.1.1166.1.19.51.1.1.1.2.1.2Columncmdot11plusWep128DefaultKeyValueread-createdeprecatedA 128-bit WEP default secret key value. This MIB object is only valid for products supporting a single SSID
1.3.6.1.4.1.1166.1.19.51.1.1.1.3Scalarcmdot11plusAclEnableread-writedeprecatedThis object controls whether MAC address ACL checking is enabled in the access point. When 'true', AP allows only those stations listed in cmdot11plusAclTable …
1.3.6.1.4.1.1166.1.19.51.1.1.1.4Tablecmdot11plusAclTablenot-accessibledeprecatedMAC ACL table contains a list of MAC addresses for stations that are allowed to associate with the access point. This MIB object is only valid for products sup…
1.3.6.1.4.1.1166.1.19.51.1.1.1.4.1Rowcmdot11plusAclEntrynot-accessibledeprecatedMAC ACL table entry. Primary column of the entry is the MAC address. This MIB object is only valid for products supporting a single SSID
1.3.6.1.4.1.1166.1.19.51.1.1.1.4.1.1Columncmdot11plusAclIndexnot-accessibledeprecatedIdentifies instances of the columnar objects in the ACL table This MIB object is only valid for products supporting a single SSID
1.3.6.1.4.1.1166.1.19.51.1.1.1.4.1.2Columncmdot11plusAclAddressread-createdeprecatedA MAC address of a station that is allowed to associate with the access point. This MIB object is only valid for products supporting a single SSID
1.3.6.1.4.1.1166.1.19.51.1.1.1.4.1.3Columncmdot11plusAclRowStatusread-createdeprecatedThe RowStatus interlock for creation and deletion. This MIB object is only valid for products supporting a single SSID
1.3.6.1.4.1.1166.1.19.51.1.1.1.5Scalarcmdot11plusSsidBroadcastEnableread-writedeprecatedWhen 'true', AP does broadcast SSID in beacon packets. When 'false', AP does not broadcast SSID in beacon packets. This MIB object is only valid for products s…
1.3.6.1.4.1.1166.1.19.51.1.1.1.6Scalarcmdot11plusBasicRatesread-writedeprecatedSet of data rates that all stations in a BSS must be capable of receiving. This MIB object is only valid for products supporting a single SSID
1.3.6.1.4.1.1166.1.19.51.1.1.1.7Scalarcmdot11plusShortPreambleEnableread-writedeprecatedWhen 'true', AP tranamits packets using a short preamble. When 'false', AP transmits packets with the standard long preamble. This MIB object is only valid for…
1.3.6.1.4.1.1166.1.19.51.1.1.1.8Scalarcmdot11plusCountersResetread-writedeprecatedSetting this object to true(1) resets the counters in dot11CountersTable. Reading this object always returns false(2). This MIB object is only valid for produc…
1.3.6.1.4.1.1166.1.19.51.1.1.1.9Scalarcmdot11plusPhyOperatingModeread-writedeprecatedThis is the supported wireless operating mode of the SBG. Select the default 11b/11g standard(1) option for most cases as this is the most flexible mode. It al…
1.3.6.1.4.1.1166.1.19.51.1.1.1.10Scalarcmdot11plusTxOutputPowerread-writedeprecatedThis object controls the ouput power of the 802.11 transmitter. The number is a percentage of the maximum power possible based on 802.11 technology and other b…
1.3.6.1.4.1.1166.1.19.51.1.1.1.11Scalarcmdot11plusWepPassPhraseread-writedeprecatedControls and reflects the WEP pass phrase. This MIB object is only valid for products supporting a single SSID
1.3.6.1.4.1.1166.1.19.51.1.1.1.12Scalarcmdot11plusGenerateWepKeysread-writedeprecatedApplies the WEP PassPhrase by generating new keys from the string set in cmdot11plusWepPassPhrase. The keys are generated using the algorithm described in 802.…
1.3.6.1.4.1.1166.1.19.51.1.1.1.13Scalarcmdot11plusSecurityModeread-writedeprecatedSets the network authentication and/or security method. WEP requires cmdot11plusWepMode to be set to either 64bit or 128bit encryption and valid keys be entere…
1.3.6.1.4.1.1166.1.19.51.1.1.2Nodecmdot11plusWpaObjects
1.3.6.1.4.1.1166.1.19.51.1.1.2.1Scalarcmdot11plusWpaAuthModeread-writedeprecatedSets the network authentication method to be used with WPA. Local(1) requires a valid WPA Pre-Shared Key to be set. This mode is sometimes called WPA-PSK. Remo…
1.3.6.1.4.1.1166.1.19.51.1.1.2.2Scalarcmdot11plusWpaGroupRekeyIntervalread-writedeprecatedSets the WPA Group Rekey Interval in seconds. Set to zero to disable periodic rekeying. This MIB object is only valid for products supporting a single SSID
1.3.6.1.4.1.1166.1.19.51.1.1.2.3Scalarcmdot11plusWpaEncryptionModeread-writedeprecatedTKIP (Temporal Key Integrity Protocol) provides data encryption enhancements including a per-packet key mixing function, a MIC, an IV(initialization vector) an…
1.3.6.1.4.1.1166.1.19.51.1.1.2.4Scalarcmdot11plusLocalPreSharedKeyread-writedeprecatedSets the WPA Pre-Shared Key (PSK). This value MUST a 8 to 63 character ASCII string. This MIB object is only valid for products supporting a single SSID
1.3.6.1.4.1.1166.1.19.51.1.1.2.5Scalarcmdot11plusRemoteRadiusIpTyperead-writedeprecatedThe address type assigned for the Radius IP address This MIB object is only valid for products supporting a single SSID
1.3.6.1.4.1.1166.1.19.51.1.1.2.6Scalarcmdot11plusRemoteRadiusIpread-writedeprecatedSets RADIUS server address. The type of address is determined by cmdot11plusRemoteRadiusIpType. If it is ipv4 then this should be set to the 4 octets represent…
1.3.6.1.4.1.1166.1.19.51.1.1.2.7Scalarcmdot11plusRemoteRadiusPortread-writedeprecatedSets the UDP port used to communicate with the RADIUS server. This MIB object is only valid for products supporting a single SSID
1.3.6.1.4.1.1166.1.19.51.1.1.2.8Scalarcmdot11plusRemoteRadiusKeyread-writedeprecatedSets or displays the RADIUS key. This MIB object is only valid for products supporting a single SSID
1.3.6.1.4.1.1166.1.19.51.1.2Nodecmdot11plusBaseObjects
1.3.6.1.4.1.1166.1.19.51.1.2.1Scalarcmdot11plusSetToFactoryread-writedeprecatedSetting this object to true(1) causes the dot11 plus default options to be returned back to factory defaults. Reading this object always returns false(2). The …
1.3.6.1.4.1.1166.1.19.51.1.2.2Scalarcmdot11plusInterfaceEnableread-writedeprecatedSetting this object to true(1) causes 802.11 interface to be enabled. Setting this object to false(2) causes 802.11 interface to be disabled. A change to this …
1.3.6.1.4.1.1166.1.19.51.1.2.3Scalarcmdot11plusApplySettingsread-writedeprecatedWhen set to true(1), all settings for 802.11 from this MIB and from the ieee802dot11 MIB will be applied to the hardware for on-the-fly reconfiguration. Always…
1.3.6.1.4.1.1166.1.19.51.1.5Nodecmdot11plusMgmtv2
1.3.6.1.4.1.1166.1.19.51.1.5.1Nodecmdot11MgmtBase
1.3.6.1.4.1.1166.1.19.51.1.5.1.1Scalarcmdot11OperModeread-writedeprecatedSetting this object to enable(1) enables the Wireless interface. Setting this object to disable(2) disables the Wireless interface.
1.3.6.1.4.1.1166.1.19.51.1.5.1.2Scalarcmdot11CurrentChannelread-onlydeprecatedReading this object displays the current channel number the access point is operating in. It displays 0 if the Wireless interface is disabled.
1.3.6.1.4.1.1166.1.19.51.1.5.1.3Scalarcmdot11ChannelSettingread-writedeprecatedThis object sets the current channel number (802.11g) or control channel (802.11n). If set to (0), the AP will be put in auto-channel mode where it automatical…
1.3.6.1.4.1.1166.1.19.51.1.5.1.10Scalarcmdot1154gNetModeread-writedeprecatedControls and reflects the behavior of the device with regards to which 802.11 mode is used. If set to mode54gLRS(5), the device will interoperate with the wide…
1.3.6.1.4.1.1166.1.19.51.1.5.1.16Scalarcmdot11NModeread-writedeprecatedUsed to enable/disable 802.11n operation. 'Auto' is used to enable 802.11n operation; the Access Point will detect which stations are out there and operate in …
1.3.6.1.4.1.1166.1.19.51.1.5.1.17Scalarcmdot11NPhyRateread-writedeprecatedUsed to specify the 802.11n PHY transmission rate. 'Auto' is used to allow the Access Point to dynamically adapt to the environment and transmit using the fast…
1.3.6.1.4.1.1166.1.19.51.1.5.1.18Scalarcmdot11NBandread-writedeprecatedSelects the wireless frequency band (2.4 GHz or 5 GHz) the Access Point will operate in. Note: This MIB object is only valid for products supporting 802.11n.
1.3.6.1.4.1.1166.1.19.51.1.5.1.19Scalarcmdot11NBandWidthread-writedeprecatedSpecifies the channel width (20 MHz or 20/40 MHz) to be used by the Access Point. When 20/40MHz is selected 802.11n clients experience improved throughput usin…
1.3.6.1.4.1.1166.1.19.51.1.5.1.20Scalarcmdot11NSideBandread-writedeprecatedWhen bonded channels (40 MHz) are used this object specifies if the control (primary) channel is in the lower or upper 20 MHz band of the bonded 40 MHz channel…
1.3.6.1.4.1.1166.1.19.51.1.5.1.21Scalarcmdot11NProtectionread-writedeprecatedDetermines if protection will be turned on or off for 802.11n mode. When set to auto, the Access Point will enable protection to allow 802.11n clients to co-ex…
1.3.6.1.4.1.1166.1.19.51.1.5.1.100Scalarcmdot11MulticastRateread-writedeprecatedControls the physical layer transmission rate used for Multicast traffic on the Wireless interface. The defined rates are the theoretical physical link rate. A…
1.3.6.1.4.1.1166.1.19.51.1.5.2Nodecmdot11MgmtInterfaceTables
1.3.6.1.4.1.1166.1.19.51.1.5.2.1Tablecmdot11BaseTablenot-accessiblecurrentA table of settings used to configure the primary wi-fi interfaces belonging to multiple wi-fi instances.
1.3.6.1.4.1.1166.1.19.51.1.5.2.1.1Rowcmdot11BaseEntrynot-accessiblecurrentAn entry describing the configuration of a primary wi-fi interface. An entry exists in this table for each entry in the ifTable with an ifType value of ieee802…
1.3.6.1.4.1.1166.1.19.51.1.5.2.1.1.1Columncmdot11WifiOperModeread-writecurrentSetting this object to enable(1) enables the Wireless interface. Setting this object to disable(2) disables the Wireless interface.
1.3.6.1.4.1.1166.1.19.51.1.5.2.1.1.2Columncmdot11WifiCurrentChannelread-onlycurrentReflects the current channel number (802.11g) or control channel (802.11n) for this interface. For 802.11g cards, available channels are 1-14. For 802.11n card…
1.3.6.1.4.1.1166.1.19.51.1.5.2.1.1.3Columncmdot11WifiBeaconIntervalread-writecurrentControls and reflects the beacon interval for this interface.
1.3.6.1.4.1.1166.1.19.51.1.5.2.1.1.4Columncmdot11WifiDTIMIntervalread-writecurrentControls and reflects the DTIM interval for this interface.
1.3.6.1.4.1.1166.1.19.51.1.5.2.1.1.5Columncmdot11WifiFragThreshread-writecurrentControls and reflects the fragmentation threshold for this interface.
1.3.6.1.4.1.1166.1.19.51.1.5.2.1.1.6Columncmdot11WifiRTSThreshread-writecurrentControls and reflects the RTS threshold for this interface.
1.3.6.1.4.1.1166.1.19.51.1.5.2.1.1.7Columncmdot11WifiShortRetryLimitread-writecurrentControls and reflects the short retry limit for this interface.
1.3.6.1.4.1.1166.1.19.51.1.5.2.1.1.8Columncmdot11WifiLongRetryLimitread-writecurrentControls and reflects the long retry limit for this interface.
1.3.6.1.4.1.1166.1.19.51.1.5.2.1.1.9Columncmdot11WifiMulticastRateread-writecurrentControls the physical layer transmission rate used for Multicast traffic on the Wireless interface. The defined rates are the theoretical physical link rate. A…
1.3.6.1.4.1.1166.1.19.51.1.5.2.1.1.10Columncmdot11WifiOutputPowerread-writecurrentSets the output power relative to the hardware's maximum capability.
1.3.6.1.4.1.1166.1.19.51.1.5.2.1.1.11Columncmdot11WifiResetToDefaultsread-writecurrentSetting this object to true(1) causes all the wireless settings including primary and Guest Network settings for a particular wi-fi instance to be reset to fac…
1.3.6.1.4.1.1166.1.19.51.1.5.2.1.1.12Columncmdot11WifiChannelSettingread-writecurrentControls and reflects the current channel number (802.11g) or control channel (802.11n) for this interface. If set to (0), the AP will be put in auto-channel m…
1.3.6.1.4.1.1166.1.19.51.1.5.2.1.1.13Columncmdot11WifiApsScanread-writecurrentIf set to true(1), the Wi-Fi Radio will be configured to scan for APs. Scan results with a list of neighboring APs will be updated in cmdot11ApsScanResultsTabl…
1.3.6.1.4.1.1166.1.19.51.1.5.2.1.1.14Columncmdot11WifiObssCoexModeread-writecurrentControls and reflects the state of the Wi-Fi Radio's OBSS Coexistence on the selected Card. If set to true(1), the AP will turn on the OBSS Coexistence for tha…
1.3.6.1.4.1.1166.1.19.51.1.5.2.1.1.15Columncmdot11WifiAcsdScanTimerread-writecurrentControls and reflects the ACS Scan Timer for this interface.
1.3.6.1.4.1.1166.1.19.51.1.5.2.1.1.16Columncmdot11WifiWMFEnableread-writecurrentControls and reflects the state of Wifi Radio's Wireless Multicast Forwarding (WMF). Set to true(1) to enable the WMF feature. Set to false(2) to disable the W…
1.3.6.1.4.1.1166.1.19.51.1.5.2.1.1.17Columncmdot11WifiBSEnableread-writecurrentControls and reflects the state of Wifi Radio's Band steering capability. Set to true(1) to enable the Band steering feature. Set to false(2) to disable the Ba…
1.3.6.1.4.1.1166.1.19.51.1.5.2.1.1.18Columncmdot11WifiATFEnableread-writecurrentControls and reflects the state of Wifi Radio's Air Time Fairness capability. Set to true(1) to enable the ATF feature. Set to false(2) to disable the ATF feat…
1.3.6.1.4.1.1166.1.19.51.1.5.2.1.1.19Columncmdot11WifiTrafficSchedulerEnableread-writecurrentControls and reflects the state of Wifi Radio's Traffic Scheduling capability. Set to true(1)to enable the Traffic Scheduler feature. Set to false(2) to disabl…
1.3.6.1.4.1.1166.1.19.51.1.5.2.1.1.20Columncmdot11WifiEbosEnableread-writecurrentControls and reflects the state of Wifi Radio's Exhausted Buffer Order Scheduling capability. Set to true(1) to enable the EBOS feature. Set to false(2) to dis…
1.3.6.1.4.1.1166.1.19.51.1.5.2.2Tablecmdot11gTablenot-accessiblecurrentA table of settings used to configure all wi-fi interfaces which are capable of supporting the ieee 802.11g standard.
1.3.6.1.4.1.1166.1.19.51.1.5.2.2.1Rowcmdot11gEntrynot-accessiblecurrentAn entry describing the configuration of 802.11g specific parameters for a primary wifi interface. An entry exists in this table for each entry in the ifTable …
1.3.6.1.4.1.1166.1.19.51.1.5.2.2.1.1Columncmdot11Wifi54gNetModeread-writecurrentControls and reflects the behavior of the interface with regards to which flavor of 802.11g is used. If set to mode54g11bOnly(0), only 802.11b clients will be …
1.3.6.1.4.1.1166.1.19.51.1.5.2.2.1.2Columncmdot11Wifi54gProtectionEnableread-writecurrentControls and reflects the state of 54g protection. If set to true(1), the AP will use RTS/CTS to improve 802.11g performance in mixed 802.11g/802.11b networks.…
1.3.6.1.4.1.1166.1.19.51.1.5.2.2.1.3Columncmdot11Wifi54gBasicRateSetread-writecurrentDetermines which rates are advertised as BASIC rates in the beacon. If set to default, the driver defaults for the selected 54gMode will be used. If set to all…
1.3.6.1.4.1.1166.1.19.51.1.5.2.3Tablecmdot11nTablenot-accessiblecurrentA table of settings used to configure all wi-fi interfaces which are capable of supporting the ieee 802.11n standard.
1.3.6.1.4.1.1166.1.19.51.1.5.2.3.1Rowcmdot11nEntrynot-accessiblecurrentAn entry describing the configuration of 802.11n specific parameters for a primary wifi interface. An entry exists in this table for each entry in the ifTable …
1.3.6.1.4.1.1166.1.19.51.1.5.2.3.1.1Columncmdot11WifiNModeread-writecurrentUsed to enable/disable 802.11n operation. 'Auto' is used to enable 802.11n operation; the Access Point will detect which stations are out there and operate in …
1.3.6.1.4.1.1166.1.19.51.1.5.2.3.1.2Columncmdot11WifiNPhyRateread-writecurrentUsed to specify the 802.11n PHY transmission rate. 'Auto' is used to allow the Access Point to dynamically adapt to the environment and transmit using the fast…
1.3.6.1.4.1.1166.1.19.51.1.5.2.3.1.3Columncmdot11WifiNBandread-writecurrentSelects the wireless frequency band (2.4 GHz or 5 GHz) the Access Point will operate in. Note: This MIB object is only valid for products supporting 802.11n.
1.3.6.1.4.1.1166.1.19.51.1.5.2.3.1.4Columncmdot11WifiNBandWidthread-writecurrentSpecifies the channel width (20 MHz or 20/40 MHz) to be used by the Access Point. When 20/40MHz is selected 802.11n clients experience improved throughput usin…
1.3.6.1.4.1.1166.1.19.51.1.5.2.3.1.5Columncmdot11WifiNSideBandread-writecurrentWhen bonded channels (40 MHz) are used this object specifies if the control (primary) channel is in the lower or upper 20 MHz band of the bonded 40 MHz channel…
1.3.6.1.4.1.1166.1.19.51.1.5.2.3.1.6Columncmdot11WifiNProtectionread-writecurrentDetermines if protection will be turned on or off for 802.11n mode. When set to auto, the Access Point will enable protection to allow 802.11n clients to co-ex…
1.3.6.1.4.1.1166.1.19.51.1.5.2.4Tablecmdot11ApsScanResultsTablenot-accessiblecurrentA table list of neighboring APs found after cmdot11WifiApsScan in cmdot11BaseTable is set to true. The table can list up to 32 APs.
1.3.6.1.4.1.1166.1.19.51.1.5.2.4.1Rowcmdot11ApsScanResultsEntrynot-accessiblecurrentAn entry describing neighboring AP information. First element cmdot11ValidEntry determines if the current entry is valid or not. The information includes SSID,…
1.3.6.1.4.1.1166.1.19.51.1.5.2.4.1.1Columncmdot11ValidEntryread-onlycurrentDetermines if the current entry is valid or not.
1.3.6.1.4.1.1166.1.19.51.1.5.2.4.1.2Columncmdot11NetworkNameread-onlycurrentNeighboring AP name or SSID.
1.3.6.1.4.1.1166.1.19.51.1.5.2.4.1.3Columncmdot11SecurityModeread-onlycurrentNeighboring AP security mode.
1.3.6.1.4.1.1166.1.19.51.1.5.2.4.1.4Columncmdot11PhyModeread-onlycurrentNeighboring AP PHY mode.
1.3.6.1.4.1.1166.1.19.51.1.5.2.4.1.5Columncmdot11Rssiread-onlycurrentNeighboring AP receive signal strength.
1.3.6.1.4.1.1166.1.19.51.1.5.2.4.1.6Columncmdot11Channelread-onlycurrentNeighboring AP operating channel.
1.3.6.1.4.1.1166.1.19.51.1.5.2.4.1.7Columncmdot11MacAddressread-onlycurrentNeighboring AP MAC address.
1.3.6.1.4.1.1166.1.19.51.1.5.2.5Tablecmdot1180211acInterfaceTablenot-accessiblecurrentA table of settings used to configure all wi-fi interfaces which are capable of supporting the ieee 802.11ac standard.
1.3.6.1.4.1.1166.1.19.51.1.5.2.5.1Rowcmdot1180211acInterfaceEntrynot-accessiblecurrentAn entry describing the configuration of 802.11ac specific parameters for a primary wifi interface. An entry exists in this table for each entry in the ifTable…
1.3.6.1.4.1.1166.1.19.51.1.5.2.5.1.1Columncmdot11ACBandWidthread-writecurrentDetermines which Bandwidth that we will be operating in: 20MHz, 40MHz or 80MHz. Note: This is for N or AC cards only.
1.3.6.1.4.1.1166.1.19.51.1.5.2.5.1.2Columncmdot11ACChannelSpecread-writecurrentControls and reflects the current channel specification for this interface. If set to (0), the AP will be put in auto-channel mode where it automatically scans…
1.3.6.1.4.1.1166.1.19.51.1.5.2.5.1.3Columncmdot11ACTxbfBFRCapread-writecurrentControls and reflects the BFR Capability on the selected Card. Set to true(1) to enable the BFR Capability for that card. Set to false(2) to disable the BFR Ca…
1.3.6.1.4.1.1166.1.19.51.1.5.2.5.1.4Columncmdot11ACTxbfBFECapread-writecurrentControls and reflects the BFE Capability on the selected Card. Set to true(1) to enable the BFE Capability for that card. Set to false(2) to disable the BFE Ca…
1.3.6.1.4.1.1166.1.19.51.1.5.4Nodecmdot11MgmtMbss
1.3.6.1.4.1.1166.1.19.51.1.5.4.1Nodecmdot11MbssBase
1.3.6.1.4.1.1166.1.19.51.1.5.4.1.14Tablecmdot11BssTablenot-accessiblecurrentA table of entries in an MBSS system.
1.3.6.1.4.1.1166.1.19.51.1.5.4.1.14.1Rowcmdot11BssEntrynot-accessiblecurrentAn entry describing the characteristics of an individual BSS. An entry exists in this table for each entry of type ieee80211 (71) in the ifTable.
1.3.6.1.4.1.1166.1.19.51.1.5.4.1.14.1.1Columncmdot11BssIdread-onlycurrentThe physical address associated with this service set.
1.3.6.1.4.1.1166.1.19.51.1.5.4.1.14.1.2Columncmdot11BssEnableread-writecurrentEnables or disables this service set.
1.3.6.1.4.1.1166.1.19.51.1.5.4.1.14.1.3Columncmdot11BssSsidread-writecurrentControls and reflects the service set identifier for this BSS.
1.3.6.1.4.1.1166.1.19.51.1.5.4.1.14.1.4Columncmdot11BssNetworkBridgeread-writeobsoleteIf set to lan(1), this service set will be authorized as a member of the local area network. If set to guest(2), this service set will have access to the wide …
1.3.6.1.4.1.1166.1.19.51.1.5.4.1.14.1.5Columncmdot11BssSecurityModeread-writecurrentSecurity mode may be chosen from Disable, WEP, WPA-PSK, WPA2-PSK, WPA-Enterprise, WPA2-Enterprise, RADIUS-WEP, WPA-PSK_WPA2-PSK or WPA-Enterprise_WPA2-Enterpri…
1.3.6.1.4.1.1166.1.19.51.1.5.4.1.14.1.6Columncmdot11BssClosedNetworkread-writecurrentControls whether the device will operate in closed network mode. If set to true(1), then the network mode is closed and the SSID will not be broadcast in beaco…
1.3.6.1.4.1.1166.1.19.51.1.5.4.1.14.1.7Columncmdot11BssAccessModeread-writecurrentControls what stations will be given access to the device. If set to allowAny(1), then any station will be allowed to connect. If set to restrictToList(2), the…
1.3.6.1.4.1.1166.1.19.51.1.5.4.1.14.1.8Columncmdot11BssMaxAssociationsLimitread-writecurrentConfigure the maximum number of stations that can associate with the device.
1.3.6.1.4.1.1166.1.19.51.1.5.4.1.14.1.9Columncmdot11BssOpmodeCapRequiredread-writecurrentConfigure operational capability requirement for a STA to associate to the BSS.
1.3.6.1.4.1.1166.1.19.51.1.5.4.2Nodecmdot11MbssSecurity
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.1Tablecmdot11BssWepTablenot-accessiblecurrentA table used to configure settings related to the WEP security modes.
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.1.1Rowcmdot11BssWepEntrynot-accessiblecurrentAn entry defining the WEP characteristics of an individual service set. A row exists in this table for each row in the cmdot11BssTable for which cmdot11BssSecu…
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.1.1.1Columncmdot11BssWepDefaultKeyread-writecurrentControls and reflects the default key which will be used when 64 or 128 bit encryption is enabled. Indicates the entry from the cmdot11BssWep64BitKeyTable if c…
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.1.1.2Columncmdot11BssWepEncryptionModeread-writecurrentSelects the WEP encryption method used by this service set. If set to wep64(1), then 64 bit WEP encryption will be used with the keys from the cmdot11BssWep64B…
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.1.1.3Columncmdot11BssWepPassPhraseread-writecurrentThe passphrase used for WEP security.
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.1.1.4Columncmdot11BssWepSharedKeyAuthenticationread-writecurrentThis object controls the use of Shared Key authentication in WEP protocol. If this object is set to optional(1), Shared Key authentication is optional. If set …
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.2Tablecmdot11BssWep64BitKeyTablenot-accessiblecurrentA table of 40 bit key values used when operating in WEP 64 mode.
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.2.1Rowcmdot11BssWep64BitKeyEntrynot-accessiblecurrentA key to be used by the row in the cmdot11BssTable identified by the value of ifIndex in the row index.
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.2.1.1Columncmdot11BssWep64BitKeyIndexnot-accessiblecurrentIdentifies an instance of a key among those used by the service set identified by the value of ifIndex in the row index.
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.2.1.2Columncmdot11BssWep64BitKeyValueread-createcurrentA 40 bit key to be used when the corresponding instance of cmdot11BssSecurityMode is set to wep(1) and the corresponding instance of cmdot11BssWepEncryptionMod…
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.2.1.3Columncmdot11BssWep64BitKeyStatusread-createcurrentThe status of this conceptual row. To create a row in this table, a manager must set this object to either createAndGo(4) or createAndWait(5). Until instances …
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.3Tablecmdot11BssWep128BitKeyTablenot-accessiblecurrentA table of 104 bit key values used when operating in WEP 128 mode.
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.3.1Rowcmdot11BssWep128BitKeyEntrynot-accessiblecurrentA key to be used by the row in the cmdot11BssTable identified by the value of ifIndex in the row index.
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.3.1.1Columncmdot11BssWep128BitKeyIndexnot-accessiblecurrentIdentifies an instance of a key among those used by the service set identified by the value of ifIndex in the row index.
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.3.1.2Columncmdot11BssWep128BitKeyValueread-createcurrentA 104 bit key to be used when the corresponding instance of cmdot11BssSecurityMode is set to wep(1) and the corresponding instance of cmdot11BssWepEncryptionMo…
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.3.1.3Columncmdot11BssWep128BitKeyStatusread-createcurrentThe status of this conceptual row. To create a row in this table, a manager must set this object to either createAndGo(4) or createAndWait(5). Until instances …
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.4Tablecmdot11BssWpaTablenot-accessiblecurrentA table used to configure settings related to the WPA security modes.
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.4.1Rowcmdot11BssWpaEntrynot-accessiblecurrentAn entry defining the WPA characteristics of an individual service set. A row exists in this table for each row in the cmdot11BssTable for which cmdot11BssSecu…
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.4.1.1Columncmdot11BssWpaAlgorithmread-writecurrentControls and reflects the WPA encryption mode used by the service set. The WPA algorithm for WPA-PSK and WPA-Enterprise security mode is either tkip(1) or aes(…
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.4.1.2Columncmdot11BssWpaPreSharedKeyread-writecurrentSets the WPA Pre-Shared Key (PSK) used by this service set. This value MUST be either a 64 byte hexadecimal number, OR an 8 to 63 character ASCII string.
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.4.1.3Columncmdot11BssWpaGroupRekeyIntervalread-writecurrentSets the WPA Group Rekey Interval for this service set. If set to zero, periodic rekeying is disabled for this service set.
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.5Tablecmdot11BssRadiusTablenot-accessiblecurrentA table used to configure settings related to the RADIUS security modes, including WPA-Enterprise, WPA2-Enterprise and RADIUS-WEP.
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.5.1Rowcmdot11BssRadiusEntrynot-accessiblecurrentAn entry defining the RADIUS characteristics of an individual service set. A row exists in this table for each row in the cmdot11BssTable for which cmdot11BssS…
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.5.1.1Columncmdot11BssRadiusAddressTyperead-writecurrentThe type of internet address used for cmdot11BssRadiusAddress.
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.5.1.2Columncmdot11BssRadiusAddressread-writecurrentThe internet address of the RADIUS server for this service set.
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.5.1.3Columncmdot11BssRadiusPortread-writecurrentThe UDP port used to communicate with the RADIUS server for this service set.
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.5.1.4Columncmdot11BssRadiusKeyread-writecurrentThe RADIUS key.
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.5.1.5Columncmdot11BssRadiusReAuthIntervalread-writecurrentThe network re-authentication interval. If set to zero, no re-authentication will be performed.
1.3.6.1.4.1.1166.1.19.51.1.5.4.2.100Scalarcmdot11BssWpaPasscoderead-onlycurrentThe WPA Passcode used to generate the WPA factory default setting.
1.3.6.1.4.1.1166.1.19.51.1.5.4.3Nodecmdot11MbssAccess
1.3.6.1.4.1.1166.1.19.51.1.5.4.3.1Tablecmdot11BssAccessTablenot-accessiblecurrentA table of MAC addresses which defines the MAC address based access restrictions for the system.
1.3.6.1.4.1.1166.1.19.51.1.5.4.3.1.1Rowcmdot11BssAccessEntrynot-accessiblecurrentA row in the table which specifies a single MAC address for a given service set.
1.3.6.1.4.1.1166.1.19.51.1.5.4.3.1.1.1Columncmdot11BssAccessIndexnot-accessiblecurrentIndicates the instance of this table row.
1.3.6.1.4.1.1166.1.19.51.1.5.4.3.1.1.2Columncmdot11BssAccessStationread-createcurrentA MAC address of a station which will be allowed to connect to the service set if cmdot11BssAccessMode is set to restrictToList(2), or forbidden if cmdot11BssA…
1.3.6.1.4.1.1166.1.19.51.1.5.4.3.1.1.3Columncmdot11BssAccessStatusread-createcurrentThe status of this conceptual row. To create a row in this table, a manager must set this object to either createAndGo(4) or createAndWait(5). Until instances …
1.3.6.1.4.1.1166.1.19.51.1.5.100Scalarcmdot11ApplySettingsread-writecurrentIf set to true(1), the wi-fi driver will be restarted using the current configuration from non-volatile storage. This object may be used to invoke an immediate…
1.3.6.1.4.1.1166.1.19.51.1.5.101Scalarcmdot11ResetToDefaultsread-writecurrentSetting this object to true(1) causes all the wireless settings including Primary and Guest Network settings for all the wi-fi instances to be reset to factory…
1.3.6.1.4.1.1166.1.19.51.1.6Nodecmdot11plusWps
1.3.6.1.4.1.1166.1.19.51.1.6.1Scalarcmdot11WpsEnableread-writecurrentSetting this object to true(1) enables the Wireless WPS feature. Setting this object to false(2) disables the Wireless WPS feature.
1.3.6.1.4.1.1166.1.19.51.1.6.2Scalarcmdot11WpsMethodread-writecurrentWPS method may be choosen from either Push Button Configuration(1) or Personal Information Number(2). if set to wpsPBC(1), user has to push a button, either an…
1.3.6.1.4.1.1166.1.19.51.1.6.3Scalarcmdot11WpsPinNumberread-writecurrentInput a wireless client's PIN number to let it be able to register with the WPS AP.
1.3.6.1.4.1.1166.1.19.51.1.6.4Scalarcmdot11WpsAddClientread-writecurrentSetting this object to true(1) starts the Wireless WPS procedure. Reading this object always returns false(2).
1.3.6.1.4.1.1166.1.19.51.1.7Nodecmdot11plusDiag
1.3.6.1.4.1.1166.1.19.51.1.7.1Scalarcmdot11WlRevInforead-onlycurrentThis MIB object provides revision information of the wireless card installed on the modem. The string includes the vendor id, version identification of the har…
1.3.6.1.4.1.1166.1.19.51.1.8Tablecmdot11plusConnectedClientsTablenot-accessiblecurrentThis table contains a list of Wi-Fi connected clients, and associated connection information.
1.3.6.1.4.1.1166.1.19.51.1.8.1Rowcmdot11plusConnectedClientsEntrynot-accessiblecurrentAn entry in the table containing connection information about a connected Wi-Fi client
1.3.6.1.4.1.1166.1.19.51.1.8.1.1Columncmdot11plusClientIndexnot-accessiblecurrentTable Index
1.3.6.1.4.1.1166.1.19.51.1.8.1.2Columncmdot11plusClientIpAddrread-onlycurrentThe IP Address assigned to the Wi-Fi client.
1.3.6.1.4.1.1166.1.19.51.1.8.1.3Columncmdot11plusClientIDread-onlycurrentThe Wi-Fi client's hardware address.
1.3.6.1.4.1.1166.1.19.51.1.8.1.4Columncmdot11plusClientHostNameread-onlycurrentThe Host Name of the Wi-Fi client, derived from DHCP option 12.
1.3.6.1.4.1.1166.1.19.51.1.8.1.5Columncmdot11plusClientAgeread-onlycurrentElapsed time in seconds since the last IP packet was received from or sent to the Wi-Fi client.
1.3.6.1.4.1.1166.1.19.51.1.8.1.6Columncmdot11plusClientModeread-onlycurrentThe connection mode of the Wi-Fi client.
1.3.6.1.4.1.1166.1.19.51.1.8.1.7Columncmdot11plusClientRssiread-onlycurrentThe Wi-Fi client's Received Signal Strength in dBm.
1.3.6.1.4.1.1166.1.19.51.1.8.1.8Columncmdot11plusClientSpeedread-onlycurrentThe Wi-Fi client's connected link speed.
1.3.6.1.4.1.1166.1.19.51.1.8.1.9Columncmdot11plusClientConnectedSSIDread-onlycurrentThe SSID (Service Set Identifier) to which the Wi-Fi client is connected.
1.3.6.1.4.1.1166.1.19.51.2Nodecmdot11plusConformance
1.3.6.1.4.1.1166.1.19.51.2.1Nodecmdot11plusCompliances
1.3.6.1.4.1.1166.1.19.51.2.1.1Compliancecmdot11plusCompliancedeprecatedThe compliance statement for access points that implement the cmdot11plus MIB This MIB object is only valid for products supporting a single SSID
1.3.6.1.4.1.1166.1.19.51.2.2Nodecmdot11plusGroups
1.3.6.1.4.1.1166.1.19.51.2.2.1Groupcmdot11plusBaseGroupdeprecatedA collection of the basic objects providing for configuration of additional 802.11 management objects not defined by the IEEE 802.11 MIB. This MIB object is on…
1.3.6.1.4.1.1166.1.19.51.2.2.2Groupcmdot11BplusGroupdeprecatedA collection of objects providing for configuration of additional 802.11 management objects for 802.11b operation. This MIB object is only valid for products s…
1.3.6.1.4.1.1166.1.19.51.2.2.3Groupcmdot11GplusGroupdeprecatedA collection of objects providing for configuration of additional 802.11 management objects for 802.11g operation. This MIB object is only valid for products s…
1.3.6.1.4.1.1166.1.19.51.2.2.4Groupcmdot11plusWpaGroupdeprecatedA collection of objects providing for configuration of additional 802.11 management objects for WPA operation. This MIB object is only valid for products suppo…
1.3.6.1.4.1.1166.1.19.51.3Nodecmdot11wifiHotspotMib
1.3.6.1.4.1.1166.1.19.51.3.1Nodecmdot11wifiHotspotBase
1.3.6.1.4.1.1166.1.19.51.3.1.1Scalarcmdot11wifiHotspotEnabledread-writecurrentEnables or disable Wifi Hotspot support in the device.
1.3.6.1.4.1.1166.1.19.51.3.1.2Tablecmdot11wifiHotspotTablenot-accessiblecurrentA table used to configure settings related to Wi-fi Hotspot.
1.3.6.1.4.1.1166.1.19.51.3.1.2.1Rowcmdot11wifiHotspotIfEntrynot-accessiblecurrentAn entry defining the Wi-fi hotspot characteristics of an individual Wi-Fi network interface.
1.3.6.1.4.1.1166.1.19.51.3.1.2.1.1Columncmdot11wifiHotspotInstancenot-accessiblecurrentThe key for a unique instance of this object.
1.3.6.1.4.1.1166.1.19.51.3.1.2.1.2Columncmdot11wifiHotspotIfread-createcurrentWi-fi network interface.
1.3.6.1.4.1.1166.1.19.51.3.1.2.1.3Columncmdot11wifiHotspotModeread-createcurrentWi-fi Hotsot mode: enableBridge - Wi-Fi traffic will be bridged enableCmdot11l2ogre - Wi-Fi traffic will be sent over GRE tunnel. GRE Tunnel should be configur…
1.3.6.1.4.1.1166.1.19.51.3.1.2.1.4Columncmdot11wifiHotspotCpeIdleTimeoutread-createcurrentCPE inactivity/idle timeout in seconds which will trigger disconnect. Value of 0 will disable inactivity tracking.
1.3.6.1.4.1.1166.1.19.51.3.1.2.1.5Columncmdot11wifiHotspotCpeSessionTimeoutread-createcurrentCPE maximum session duration timeout in seconds. Value of 0 will disable tracking session duration.
1.3.6.1.4.1.1166.1.19.51.3.1.2.1.6Columncmdot11wifiHotspotRadiusAccAddressTyperead-createcurrentThe type of internet address used for cmdot11wifiHotspotRadiusAccAddress.
1.3.6.1.4.1.1166.1.19.51.3.1.2.1.7Columncmdot11wifiHotspotRadiusAccAddressread-createcurrentThe internet address of the RADIUS Accounting server for this service set.
1.3.6.1.4.1.1166.1.19.51.3.1.2.1.8Columncmdot11wifiHotspotRadiusAccPortread-createcurrentThe UDP port used to communicate with the RADIUS Accounting server. Default value set to 1813.
1.3.6.1.4.1.1166.1.19.51.3.1.2.1.9Columncmdot11wifiHotspotRadiusAccKeyread-createcurrentThe RADIUS Accounting server shared security key.
1.3.6.1.4.1.1166.1.19.51.3.1.2.1.10Columncmdot11wifiHotspotPacketFilterMaskread-createcurrentBit mask for limiting traffic to certain packet types. Possible value: 11111111 11111111 11111111 11111111: Allow All traffic xxxxxxxx xxxxxxxx xxxxxxxx xxxxxx…
1.3.6.1.4.1.1166.1.19.51.3.1.2.1.11Columncmdot11wifiHotspotInsertDhcpOptionsMaskread-createcurrentBit mask for inserting DHCP options in DHCP Discover/Request packet from connected wifi client device. Possible value: 0x1: Insert DHCP relay agent option 82. …
1.3.6.1.4.1.1166.1.19.51.3.1.2.1.12Columncmdot11wifiHotspotRowStatusread-createcurrentThe RowStatus interlock for the creation and deletion can be modified at any time while the row is active(1).
1.3.6.1.4.1.1166.1.19.51.3.1.3Scalarcmdot11wifiHotspotAutRateLimitread-writecurrentAuthentication rate limit in messages per second. If client exceeds this limit, authentication from the client is ignored for cmdot11wifiHotspotAutDenialTimeou…
1.3.6.1.4.1.1166.1.19.51.3.1.4Scalarcmdot11wifiHotspotAutDenialTimeoutread-writecurrentTimeout in seconds during which authentication from a client is ignored once authentication message rate exceeds cmdot11wifiHotspotAutRateLimit.
1.3.6.1.4.1.1166.1.19.51.3.1.5Scalarcmdot11wifiHotspotRadiusOrigIfread-writecurrentOriginating interface of radius authentication and accounting traffic.
1.3.6.1.4.1.1166.1.19.51.3.1.6Scalarcmdot11wifiHotspotIgnoreMaxCpeSettingread-writecurrentThis setting is applicable for wifi hotspot bridged mode. When set to true(1), clients connected through the hotspot wifi will not be counted when enforcing th…
1.3.6.1.4.1.1166.1.19.51.3.1.7Scalarcmdot11wifiHotspotDisablePMKCachingread-writecurrentEnables or disable WPA2 PMK Caching.
1.3.6.1.4.1.1166.1.19.51.3.1.8Scalarcmdot11wifiHotspotConnectionSpeedMinread-writecurrentMinimum connection speed in kbps required by client to maintain connectivity.
1.3.6.1.4.1.1166.1.19.51.3.1.9Scalarcmdot11wifiHotspotConnectionSpeedTimeoutread-writecurrentTimeout in seconds during which client is allowed to maintain connectivity once connection speed is below cmdot11wifiHotspotConnectionSpeedMin. When timeout ex…
1.3.6.1.4.1.1166.1.19.51.4Nodecmdot11l2ogreMib
1.3.6.1.4.1.1166.1.19.51.4.1Nodecmdot11l2ogreBase
1.3.6.1.4.1.1166.1.19.51.4.1.1Scalarcmdot11l2ogreEnabledread-writecurrentEnables or disable GRE Tunnel support in the device.
1.3.6.1.4.1.1166.1.19.51.4.1.2Scalarcmdot11l2ogrePriRemoteAddressTyperead-writecurrentThe IP address type (ipv4, ipv6 or dns) of primary remote endpoint of the GRE tunnel.
1.3.6.1.4.1.1166.1.19.51.4.1.3Scalarcmdot11l2ogrePriRemoteAddressread-writecurrentIP address or FQDN of primary remote endpoint of the GRE tunnel.
1.3.6.1.4.1.1166.1.19.51.4.1.4Scalarcmdot11l2ogreSecRemoteAddressTyperead-writecurrentThe IP address type (ipv4, ipv6 or dns) of secondary remote endpoint of the GRE tunnel.
1.3.6.1.4.1.1166.1.19.51.4.1.5Scalarcmdot11l2ogreSecRemoteAddressread-writecurrentIP address or FQDN of secondary remote endpoint of the GRE tunnel.
1.3.6.1.4.1.1166.1.19.51.4.1.6Scalarcmdot11l2ogreDSCPread-writecurrentThe method is used to set the high 6 bits of TOS in the IPv4 header or traffic class in IPv6 header.
1.3.6.1.4.1.1166.1.19.51.4.1.7Scalarcmdot11l2ogreKeepAliveModeread-writecurrentKeepalive modes for failover mechanism. ping - Use ICMP pings within tunnel as a keepalive messages.
1.3.6.1.4.1.1166.1.19.51.4.1.8Scalarcmdot11l2ogreKeepAliveCountread-writecurrentNumber of keep-alive messages sent at regular interval.
1.3.6.1.4.1.1166.1.19.51.4.1.9Scalarcmdot11l2ogreKeepAliveIntervalread-writecurrentInterval in seconds between keep-alive messages.
1.3.6.1.4.1.1166.1.19.51.4.1.10Scalarcmdot11l2ogreKeepAliveFailureThresholdread-writecurrentNumber of keep-alive failures that will cause fail-over.
1.3.6.1.4.1.1166.1.19.51.4.1.11Tablecmdot11l2ogreStatsTablenot-accessiblecurrentThis table provides statistical information of GRE tunnel.
1.3.6.1.4.1.1166.1.19.51.4.1.11.1Rowcmdot11l2ogreStatsEntrynot-accessiblecurrentThis table provides statistical information of GRE tunnel.
1.3.6.1.4.1.1166.1.19.51.4.1.11.1.1Columncmdot11l2ogreStatsIndexnot-accessiblecurrentTable index
1.3.6.1.4.1.1166.1.19.51.4.1.11.1.2Columncmdot11l2ogreStatsBytesSentread-onlycurrentNumber bytes sent.
1.3.6.1.4.1.1166.1.19.51.4.1.11.1.3Columncmdot11l2ogreStatsBytesReceivedread-onlycurrentNumber bytes received.
1.3.6.1.4.1.1166.1.19.51.4.1.11.1.4Columncmdot11l2ogreStatsPacketsSentread-onlycurrentNumber packets sent.
1.3.6.1.4.1.1166.1.19.51.4.1.11.1.5Columncmdot11l2ogreStatsPacketsReceivedread-onlycurrentNumber packets received.
1.3.6.1.4.1.1166.1.19.51.4.1.11.1.6Columncmdot11l2ogreStatsDiscardPacketsReceivedread-onlycurrentNumber packets received that were discarded. Because source network interface is down.
1.3.6.1.4.1.1166.1.19.51.4.1.11.1.7Columncmdot11l2ogreStatsErrorPacketsReceivedread-onlycurrentNumber packets received that were in error. Because tunnel packets are not correct type. Eg. Received IP packet instead of L2 packets.
1.3.6.1.4.1.1166.1.19.51.4.1.11.1.8Columncmdot11l2ogreStatsKeepAliveSentread-onlycurrentNumber keepalive packets sent.
1.3.6.1.4.1.1166.1.19.51.4.1.11.1.9Columncmdot11l2ogreStatsKeepAliveReceivedread-onlycurrentNumber keepalive packets received.
1.3.6.1.4.1.1166.1.19.51.4.1.11.1.10Columncmdot11l2ogreStatsRowStatusread-createcurrentThe RowStatus interlock for the creation and deletion can be modified at any time while the row is active(1).
1.3.6.1.4.1.1166.1.19.51.4.1.12Tablecmdot11l2ogreSourceIfTablenot-accessiblecurrentThis table contains information specific to network source interface whose traffic is mapped into GRE tunnel.
1.3.6.1.4.1.1166.1.19.51.4.1.12.1Rowcmdot11l2ogreSourceIfEntrynot-accessiblecurrentList of individual source interface entries mapped into GRE tunnel.
1.3.6.1.4.1.1166.1.19.51.4.1.12.1.1Columncmdot11l2ogreSourceIfInstancenot-accessiblecurrentThe key for a unique instance of this object.
1.3.6.1.4.1.1166.1.19.51.4.1.12.1.2Columncmdot11l2ogreSourceIfread-createcurrentSource interface whose traffic will be pass through GRE tunnel.
1.3.6.1.4.1.1166.1.19.51.4.1.12.1.3Columncmdot11l2ogreSourceIfEnabledread-createcurrentEnables or disable mapping traffic from network interface into GRE tunnel.
1.3.6.1.4.1.1166.1.19.51.4.1.12.1.4Columncmdot11l2ogreSourceIfVlanTagread-createcurrentAdd VLAN tag consists of 16bit of Tag Protocol Identifier (TPID) and 16 bit of Tag Control Identifier (TCI). Value of 0 will disable adding VLAN tag. Tag Proto…
1.3.6.1.4.1.1166.1.19.51.4.1.12.1.5Columncmdot11l2ogreSourceIfMplsHeaderread-createcurrentMPLS Header. Value of 0 will disable adding MPLS Header.
1.3.6.1.4.1.1166.1.19.51.4.1.12.1.6Columncmdot11l2ogreSourceIfRowStatusread-createcurrentThe RowStatus interlock for the creation and deletion of a table entry.
1.3.6.1.4.1.1166.1.19.51.4.1.13Scalarcmdot11l2ogreOrigIfread-writecurrentOriginating Interface of GRE tunnel.
1.3.6.1.4.1.1166.1.19.51.4.1.14Scalarcmdot11l2ogreConcentratorServiceNameread-writecurrentFQDN of GRE tunnel concentrator/gw service. If this is set then, DNS Query of type SRV will be used for discovering FQDN of primary and secondary remote endpoi…
1.3.6.1.4.1.1166.1.19.51.4.1.15Scalarcmdot11l2ogreDnsResolverRetryTimerMinread-writecurrentMinimum timeout interval in seconds before retrying DNS query.
1.3.6.1.4.1.1166.1.19.51.4.1.16Scalarcmdot11l2ogreDnsResolverRetryTimerMaxread-writecurrentMaximum timeout interval in seconds before retrying DNS query.