MIB Viewer

LUM-CLIENT-MIB

316 objects
The generic client interface MIB. - General - Generic client interfaces
Imported Objects
LUM-REGlumClientMIB lumModules
LUM-TCBerLevelMTOSI BoardOrInterfaceAdminStatus BoardOrInterfaceOperStatus CommandString EnableDisable FaultStatus InterfaceType LambdaFrequency LaneFrequency MgmtNameString ObjectProperty OnOff OpticalLayerMappingType PhysicalLayerMappingType PortNumber SignalDirection SignalFormat SignalStatusWithNA SlotNumber SubrackNumber TrxMedia TrxRxState TrxTxState
SNMPv2-CONFMODULE-COMPLIANCE NOTIFICATION-GROUP OBJECT-GROUP
SNMPv2-SMIGauge32 Integer32 MODULE-IDENTITY NOTIFICATION-TYPE OBJECT-TYPE Unsigned32
SNMPv2-TCDateAndTime DisplayString
OIDNameAccessStatusDescription
1.3.6.1.4.1.8708.1.1.27IdentitylumClientMIBModuleThe generic client interface MIB. - General - Generic client interfaces
1.3.6.1.4.1.8708.2.27.1NodelumClientConfs
1.3.6.1.4.1.8708.2.27.1.1NodelumClientGroups
1.3.6.1.4.1.8708.2.27.1.1.1GroupclientGeneralGroupV1deprecatedThe generic client interface MIB general objects v1.
1.3.6.1.4.1.8708.2.27.1.1.2GroupclientNotificationGroupV1currentThe generic client interface notifications.
1.3.6.1.4.1.8708.2.27.1.1.3GroupclientIfGroupV1deprecatedThe interface objects V1 (3.0).
1.3.6.1.4.1.8708.2.27.1.1.4GroupclientIfGroupV2deprecatedThe interface objects V2 (3.1).
1.3.6.1.4.1.8708.2.27.1.1.5GroupclientGeneralGroupV2currentThe generic client interface MIB general objects V2 (3.1).
1.3.6.1.4.1.8708.2.27.1.1.6GroupclientIfGroupV3deprecatedThe interface objects V3 (3.2).
1.3.6.1.4.1.8708.2.27.1.1.7GroupclientIfGroupV4deprecatedThe interface objects V4 (4.0).
1.3.6.1.4.1.8708.2.27.1.1.8GroupclientIfGroupV5deprecatedThe interface objects V5 (4.1).
1.3.6.1.4.1.8708.2.27.1.1.9GroupclientIfGroupV6deprecatedThe interface objects V6 (5.0).
1.3.6.1.4.1.8708.2.27.1.1.10GroupclientIfGroupV7deprecatedThe interface objects V7 (7.0).
1.3.6.1.4.1.8708.2.27.1.1.11GroupclientIfGroupV8deprecatedThe interface objects V8 (8.0).
1.3.6.1.4.1.8708.2.27.1.1.12GroupclientVc4GroupdeprecatedThe vc4 objects (10.0).
1.3.6.1.4.1.8708.2.27.1.1.13GroupclientGeneralGroupV3currentThe generic client interface MIB general objects V2 (10.0).
1.3.6.1.4.1.8708.2.27.1.1.14GroupclientIfGroupV9deprecatedThe interface objects V9 (11.0).
1.3.6.1.4.1.8708.2.27.1.1.15GroupclientIfGroupV10deprecatedThe interface objects V10 (12.0).
1.3.6.1.4.1.8708.2.27.1.1.16GroupclientIfGroupV11deprecatedThe interface objects V11 (13.0).
1.3.6.1.4.1.8708.2.27.1.1.17GroupclientIfGroupV12deprecatedThe interface objects V11 (15.0).
1.3.6.1.4.1.8708.2.27.1.1.18GroupclientIfGroupV13deprecatedThe interface objects V13 (16.0).
1.3.6.1.4.1.8708.2.27.1.1.19GroupclientVc4GroupV2currentThe vc4 objects V2 (16.0).
1.3.6.1.4.1.8708.2.27.1.1.20GroupclientIfGroupV14deprecatedThe interface objects V14 (16.1).
1.3.6.1.4.1.8708.2.27.1.1.21GroupclientIfGroupV15deprecatedThe interface objects V15 (17.0).
1.3.6.1.4.1.8708.2.27.1.1.22GroupclientIfGroupV16deprecatedThe interface objects V16 (19.0).
1.3.6.1.4.1.8708.2.27.1.1.23GroupclientIfGroupV17deprecatedThe interface objects V17 (20.0).
1.3.6.1.4.1.8708.2.27.1.1.24GroupclientLanesGroupdeprecatedThe lane objects (20.0).
1.3.6.1.4.1.8708.2.27.1.1.25GroupclientIfGroupV18deprecatedThe interface objects V18 (20.0).
1.3.6.1.4.1.8708.2.27.1.1.26GroupclientIfGroupV19deprecatedThe interface objects V19 (21.0).
1.3.6.1.4.1.8708.2.27.1.1.27GroupclientIfGroupV20deprecatedThe interface objects V20 (23.0).
1.3.6.1.4.1.8708.2.27.1.1.28GroupclientLanesGroupV2deprecatedThe lane objects V2 (23.0).
1.3.6.1.4.1.8708.2.27.1.1.29GroupclientIfGroupV21deprecatedThe interface objects V20 (23.1).
1.3.6.1.4.1.8708.2.27.1.1.30GroupclientIfGroupV22deprecatedThe interface objects V22 (26.1).
1.3.6.1.4.1.8708.2.27.1.1.31GroupclientLanesGroupV3deprecatedThe lane objects V3 (26.1).
1.3.6.1.4.1.8708.2.27.1.1.32GroupclientLanesGroupV4deprecatedThe lane objects V4 (26.1).
1.3.6.1.4.1.8708.2.27.1.1.33GroupclientMpoLanesGroupV1currentThe mpo lane objects (release 27.0).
1.3.6.1.4.1.8708.2.27.1.1.34GroupclientLanesGroupV5currentThe lane objects V5 (28.1).
1.3.6.1.4.1.8708.2.27.1.1.35GroupclientIfGroupV23deprecatedThe interface objects V23 (28.0).
1.3.6.1.4.1.8708.2.27.1.1.36GroupclientIfGroupV24deprecatedThe interface objects V24 (29.0).
1.3.6.1.4.1.8708.2.27.1.1.37GroupclientIfGroupV25deprecatedThe interface objects V25 (30.0).
1.3.6.1.4.1.8708.2.27.1.1.38GroupclientIfGroupV26deprecatedThe interface objects V26 (30.1).
1.3.6.1.4.1.8708.2.27.1.1.39GroupclientIfGroupV27currentThe interface objects V27 (31.1).
1.3.6.1.4.1.8708.2.27.1.2NodelumClientCompl
1.3.6.1.4.1.8708.2.27.1.2.1CompliancelumClientBasicComplV1deprecatedBasic implementation requirements for the client MIB V1 (3.0).
1.3.6.1.4.1.8708.2.27.1.2.2CompliancelumClientBasicComplV2deprecatedBasic implementation requirements for the client MIB V2 (3.1).
1.3.6.1.4.1.8708.2.27.1.2.3CompliancelumClientBasicComplV3deprecatedBasic implementation requirements for the client MIB V3 (3.2).
1.3.6.1.4.1.8708.2.27.1.2.4CompliancelumClientBasicComplV4deprecatedBasic implementation requirements for the client MIB V4 (4.0).
1.3.6.1.4.1.8708.2.27.1.2.5CompliancelumClientBasicComplV5deprecatedBasic implementation requirements for the client MIB V5 (4.1).
1.3.6.1.4.1.8708.2.27.1.2.6CompliancelumClientBasicComplV6deprecatedBasic implementation requirements for the client MIB V6 (5.0).
1.3.6.1.4.1.8708.2.27.1.2.7CompliancelumClientBasicComplV7deprecatedBasic implementation requirements for the client MIB V7 (7.0).
1.3.6.1.4.1.8708.2.27.1.2.8CompliancelumClientBasicComplV8deprecatedBasic implementation requirements for the client MIB V8 (8.0).
1.3.6.1.4.1.8708.2.27.1.2.9CompliancelumClientBasicComplV9deprecatedBasic implementation requirements for the client MIB v9 (10.0).
1.3.6.1.4.1.8708.2.27.1.2.10CompliancelumClientBasicComplV10deprecatedBasic implementation requirements for the client MIB v10 (11.0).
1.3.6.1.4.1.8708.2.27.1.2.11CompliancelumClientBasicComplV11deprecatedBasic implementation requirements for the client MIB v11 (12.0).
1.3.6.1.4.1.8708.2.27.1.2.12CompliancelumClientBasicComplV12deprecatedBasic implementation requirements for the client MIB v12 (13.0).
1.3.6.1.4.1.8708.2.27.1.2.13CompliancelumClientBasicComplV13deprecatedBasic implementation requirements for the client MIB v13 (15.0).
1.3.6.1.4.1.8708.2.27.1.2.14CompliancelumClientBasicComplV14deprecatedBasic implementation requirements for the client MIB v14 (16.0).
1.3.6.1.4.1.8708.2.27.1.2.15CompliancelumClientBasicComplV15deprecatedBasic implementation requirements for the client MIB v15 (16.1). 16.1 was never released
1.3.6.1.4.1.8708.2.27.1.2.16CompliancelumClientBasicComplV16deprecatedBasic implementation requirements for the client MIB v16 (17.0).
1.3.6.1.4.1.8708.2.27.1.2.17CompliancelumClientBasicComplV17deprecatedBasic implementation requirements for the client MIB v17 (19.0).
1.3.6.1.4.1.8708.2.27.1.2.18CompliancelumClientBasicComplV18deprecatedBasic implementation requirements for the client MIB v18 (20.0).
1.3.6.1.4.1.8708.2.27.1.2.19CompliancelumClientBasicComplV19deprecatedBasic implementation requirements for the client MIB v18 (20.0).
1.3.6.1.4.1.8708.2.27.1.2.20CompliancelumClientBasicComplV20deprecatedBasic implementation requirements for the client MIB v20 (21.0).
1.3.6.1.4.1.8708.2.27.1.2.21CompliancelumClientBasicComplV21deprecatedBasic implementation requirements for the client MIB v21 (23.0).
1.3.6.1.4.1.8708.2.27.1.2.22CompliancelumClientBasicComplV22deprecatedBasic implementation requirements for the client MIB v22 (23.1).
1.3.6.1.4.1.8708.2.27.1.2.23CompliancelumClientBasicComplV23deprecatedBasic implementation requirements for the client MIB v23 (26.1).
1.3.6.1.4.1.8708.2.27.1.2.24CompliancelumClientBasicComplV24deprecatedBasic implementation requirements for the client MIB v24 (27).
1.3.6.1.4.1.8708.2.27.1.2.25CompliancelumClientBasicComplV25deprecatedBasic implementation requirements for the client MIB v25 (28.1).
1.3.6.1.4.1.8708.2.27.1.2.26CompliancelumClientBasicComplV26deprecatedBasic implementation requirements for the client MIB v26 (28.0).
1.3.6.1.4.1.8708.2.27.1.2.27CompliancelumClientBasicComplV27deprecatedBasic implementation requirements for the client MIB v27 (29.0).
1.3.6.1.4.1.8708.2.27.1.2.28CompliancelumClientBasicComplV28deprecatedBasic implementation requirements for the client MIB v28 (30.0).
1.3.6.1.4.1.8708.2.27.1.2.29CompliancelumClientBasicComplV29deprecatedBasic implementation requirements for the client MIB v29 (30.1).
1.3.6.1.4.1.8708.2.27.1.2.30CompliancelumClientBasicComplV30currentBasic implementation requirements for the client MIB v30 (31.1).
1.3.6.1.4.1.8708.2.27.1.3NodelumClientMinimalGroups
1.3.6.1.4.1.8708.2.27.1.3.1GroupclientIfMinimalGroupV1deprecatedThe minimal interface objects.
1.3.6.1.4.1.8708.2.27.1.3.2GroupclientIfMinimalGroupV2currentThe minimal interface objects.
1.3.6.1.4.1.8708.2.27.1.4NodelumClientMinimalCompl
1.3.6.1.4.1.8708.2.27.1.4.1CompliancelumClientMinimalComplV1deprecatedMinimal implementation requirements for the client MIB v1.
1.3.6.1.4.1.8708.2.27.1.4.2CompliancelumClientMinimalComplV2currentMinimal implementation requirements for the client MIB v2.
1.3.6.1.4.1.8708.2.27.2NodelumClientMIBObjects
1.3.6.1.4.1.8708.2.27.2.1NodeclientGeneral
1.3.6.1.4.1.8708.2.27.2.1.1ScalarclientGeneralLastChangeTimeread-onlycurrentThe time when the configuration of the MIB was last changed.
1.3.6.1.4.1.8708.2.27.2.1.2ScalarclientGeneralStateLastChangeTimeread-onlycurrentThe time when the state of the MIB was last changed.
1.3.6.1.4.1.8708.2.27.2.1.3ScalarclientGeneralClientIfTableSizeread-onlycurrentSize of table
1.3.6.1.4.1.8708.2.27.2.1.4ScalarclientGeneralVc4TableSizeread-onlycurrentSize of table
1.3.6.1.4.1.8708.2.27.2.1.5ScalarclientGeneralLanesTableSizeread-onlycurrentSize of table
1.3.6.1.4.1.8708.2.27.2.1.6ScalarclientGeneralMpoLanesTableSizeread-onlycurrentSize of table
1.3.6.1.4.1.8708.2.27.2.2NodeclientIfList
1.3.6.1.4.1.8708.2.27.2.2.1TableclientIfTablenot-accessiblecurrentThe interface list.
1.3.6.1.4.1.8708.2.27.2.2.1.1RowclientIfEntrynot-accessiblecurrentAn entry in the interface list.
1.3.6.1.4.1.8708.2.27.2.2.1.1.1ColumnclientIfIndexread-createcurrentAn arbitrary index assigned to each entry.
1.3.6.1.4.1.8708.2.27.2.2.1.1.2ColumnclientIfNameread-createcurrentThe management name of the interface, for example 'client:1:2:1', where the first number indicates sub-rack, the second slot number and the third is the port n…
1.3.6.1.4.1.8708.2.27.2.2.1.1.3ColumnclientIfDescrread-writecurrentUser configurable label. This attribute can be written via SNMP.
1.3.6.1.4.1.8708.2.27.2.2.1.1.4ColumnclientIfSubrackread-createcurrentThe number of the subrack where the interface is located.
1.3.6.1.4.1.8708.2.27.2.2.1.1.5ColumnclientIfSlotread-createcurrentThe number of the slot where the interface is located.
1.3.6.1.4.1.8708.2.27.2.2.1.1.6ColumnclientIfTxPortread-createcurrentThe number of the port where the TX-side of the interface is located.
1.3.6.1.4.1.8708.2.27.2.2.1.1.7ColumnclientIfRxPortread-createcurrentThe number of the port where the RX-side of the interface is located.
1.3.6.1.4.1.8708.2.27.2.2.1.1.8ColumnclientIfInvPhysIndexOrZeroread-createcurrentThe row in the invPhysTable for this interface. Set to 0 if not known.
1.3.6.1.4.1.8708.2.27.2.2.1.1.9ColumnclientIfEntityIdread-createcurrentIndex in entity table.
1.3.6.1.4.1.8708.2.27.2.2.1.1.10ColumnclientIfAdminStatusread-writecurrentThe administrative state for the interface. down - The interface is de-activated. service - The interface is activated but alarms are suppressed. Intended for …
1.3.6.1.4.1.8708.2.27.2.2.1.1.11ColumnclientIfOperStatusread-onlycurrentThe operational state for the interface. notPresent - The physical resources are not available. down - The interface is de-activated or there are faults preven…
1.3.6.1.4.1.8708.2.27.2.2.1.1.12ColumnclientIfLaserStatusread-onlycurrentThe operational state of the laser. off - The laser is turned off. on - The laser is turned on.
1.3.6.1.4.1.8708.2.27.2.2.1.1.13ColumnclientIfTxSignalStatusread-onlycurrentThe operational state for outgoing (TX) signal of the interface. down - A fault that would lead to a protection switch has occurred. degraded - The signal qual…
1.3.6.1.4.1.8708.2.27.2.2.1.1.14ColumnclientIfForwardAlsread-writecurrentForward Automatic Laser Shut-down. Decides if laser shutdown of the client should occur when a defect on the line or remote client is detected. disabled - The …
1.3.6.1.4.1.8708.2.27.2.2.1.1.15ColumnclientIfSuppressRemoteAlarmsread-writecurrentSuppress AIS in the alarm list. The fault status on the port object can, however, be seen. disabled - alarms are not suppressed. enabled - alarms are suppresse…
1.3.6.1.4.1.8708.2.27.2.2.1.1.16ColumnclientIfFarEndLoopbackread-writecurrentLoop the client TX signal back to the client RX. This is also called Terminal loopback. disabled - the signal is not looped enabled - the signal is looped.
1.3.6.1.4.1.8708.2.27.2.2.1.1.17ColumnclientIfFormatread-createcurrentThe expected signal format. The default value is board dependent. For information about the default value for this particular board, please refer to the user m…
1.3.6.1.4.1.8708.2.27.2.2.1.1.18ColumnclientIfGfpModeread-createcurrentGeneric framing procedure mode
1.3.6.1.4.1.8708.2.27.2.2.1.1.19ColumnclientIfBandWidthread-createcurrentBand-width in VC-3 or VC-4. The parameter is interpreted as VC-3 or VC-4 depending on the traffic combination: - VC-3 is used in framedGbEx10 - VC-4 is used in…
1.3.6.1.4.1.8708.2.27.2.2.1.1.20ColumnclientIfRateLimitread-writecurrentRate limit of link in 1,000,000 bits (Mb) per second. Zero (0) is a special value meaning that the rate-limiting procedure is disabled. The legal range is: 10.…
1.3.6.1.4.1.8708.2.27.2.2.1.1.21ColumnclientIfAutoNegotiationModeread-writecurrentThe wanted auto negotiation mode. off - auto negotiation process is disabled on - auto negotiation process is enabled
1.3.6.1.4.1.8708.2.27.2.2.1.1.22ColumnclientIfAutoNegotiationStatusread-onlycurrentThe result of the auto negotiation procedure incomplete - the result is still pending half - half duplex full - full duplex
1.3.6.1.4.1.8708.2.27.2.2.1.1.23ColumnclientIfDuplexCapabilityread-onlycurrentThe duplex capability of the HW. half - supports half duplex full - supports full duplex
1.3.6.1.4.1.8708.2.27.2.2.1.1.24ColumnclientIfFlowControlModeread-writecurrentThe mode for handling flow control between the local device and link partner. The PAUSE settings has the following meaning when auto-negotiation is enabled. Se…
1.3.6.1.4.1.8708.2.27.2.2.1.1.25ColumnclientIfInterPacketGapread-writecurrentTime between the frames in nano seconds. Legal values are 64, 72, 80, ... 200, 320, 328, 336, ... 456
1.3.6.1.4.1.8708.2.27.2.2.1.1.26ColumnclientIfFrameSizeread-writecurrentThe maximum size of the transmitted and received frames (in bytes).
1.3.6.1.4.1.8708.2.27.2.2.1.1.27ColumnclientIfTrxClassread-onlycurrentString that describes the transceiver class.
1.3.6.1.4.1.8708.2.27.2.2.1.1.28ColumnclientIfLaserBiasread-onlycurrentMeasures laser bias current value in tenths of mA (0.1 mA).
1.3.6.1.4.1.8708.2.27.2.2.1.1.29ColumnclientIfPowerLevelread-onlycurrentThe received power level in units of 0.1 dBm.
1.3.6.1.4.1.8708.2.27.2.2.1.1.30ColumnclientIfReceiverSensitivityread-onlycurrentThe lowest power that the receiver is guaranteed to handle, in units of 0.1 dBm.
1.3.6.1.4.1.8708.2.27.2.2.1.1.31ColumnclientIfPowerLevelLowRelativeThresholdread-writecurrentThe lower threshold for received power level in units of 0.1 dB, relative to the receiver sensitivity.
1.3.6.1.4.1.8708.2.27.2.2.1.1.32ColumnclientIfLossOfSignalread-onlycurrentLoss of signal. Applicable for all signal formats. A(ctivation): Active loss of signal HW indication. D(e-activation): Inactive loss of signal HW indication.
1.3.6.1.4.1.8708.2.27.2.2.1.1.33ColumnclientIfLossOfFrameread-onlycurrentLoss of frame. All forms of sync loss.
1.3.6.1.4.1.8708.2.27.2.2.1.1.34ColumnclientIfBitrateMismatchread-onlycurrentBitrate mismatch (Other). Applicable for other signal formats. D: The interface is unable to lock to the inserted signal. D: The interface is able to lock to t…
1.3.6.1.4.1.8708.2.27.2.2.1.1.35ColumnclientIfAuAlarmIndicationSignalW2Cread-onlycurrentAlarm indication signal (AIS) on the trunk-side. Applicable for SDH/Sonet signal formats. A: An 'all ones' SDH signal is detected. D: SDH signal recovered.
1.3.6.1.4.1.8708.2.27.2.2.1.1.36ColumnclientIfTransmitterFailedread-onlycurrentThe transceiver HW has detected a failure in the transmitter part. A: The transmitter has failed D: The transmitter is OK again
1.3.6.1.4.1.8708.2.27.2.2.1.1.37ColumnclientIfTrxCodeMismatchread-onlycurrentThe inserted transceiver does not have a legal manufacturer code. A: A transceiver with illegal code is inserted. D: The transceiver with illegal code is remov…
1.3.6.1.4.1.8708.2.27.2.2.1.1.38ColumnclientIfTrxBitrateUnavailableread-onlycurrentThe inserted transceiver does not support the requested bit rate. A: A transceiver with other supported bit rate than the requested bit rate is inserted. D: Th…
1.3.6.1.4.1.8708.2.27.2.2.1.1.39ColumnclientIfTrxMissingread-onlycurrentAn expected transceiver is missing. A: An expected transceiver is missing. D: The missing transceiver is inserted.
1.3.6.1.4.1.8708.2.27.2.2.1.1.40ColumnclientIfReceivedPowerHighread-onlycurrentReceived power level is too high. Applicable for all signal formats. A: The received power level exceeds the the built-in overload threshold. D: The received p…
1.3.6.1.4.1.8708.2.27.2.2.1.1.41ColumnclientIfReceivedPowerLowread-onlycurrentReceived power level low threshold exceeded. Applicable for all signal formats. A: The received power level is below the associated threshold. D: The received …
1.3.6.1.4.1.8708.2.27.2.2.1.1.42ColumnclientIfLinkDownread-onlycurrentA: Failure to negotiate a connection with the other party. D: A connection is negotiated.
1.3.6.1.4.1.8708.2.27.2.2.1.1.43ColumnclientIfConfigurationCommandread-onlycurrentCommand to change the signal format, and, if applicable, also the mode (framed, transparent).
1.3.6.1.4.1.8708.2.27.2.2.1.1.44ColumnclientIfGbeUtilizationread-onlycurrentShows the current bandwidth utilization measured at the physical (802.3 PHY) layer. The value represents a snapshot of the utilization during the latest second…
1.3.6.1.4.1.8708.2.27.2.2.1.1.45ColumnclientIfLossOfSyncread-onlycurrentLoss of sync. All forms of sync loss. A: GbE 'frame' can not be located. D: GbE 'frame' is located.
1.3.6.1.4.1.8708.2.27.2.2.1.1.46ColumnclientIfConfigureTrxModeCommandread-onlycurrentCommand to change the TRX mode (client or line) and/or TRX media (optical or electrical).
1.3.6.1.4.1.8708.2.27.2.2.1.1.47ColumnclientIfTrxModeread-createcurrentShows if the port is configured as: - normal CLIENT interface connected to a non XTM Series client equipment, with non-colored, or colored TRXes. - a LINE inte…
1.3.6.1.4.1.8708.2.27.2.2.1.1.48ColumnclientIfExpectedTxFrequencyread-writecurrentThe expected frequency given in hundreds of GHz (0.01 GHz).
1.3.6.1.4.1.8708.2.27.2.2.1.1.49ColumnclientIfTxFrequencyread-onlycurrentThe transmitted frequency given in hundreds of GHz (0.01 GHz).
1.3.6.1.4.1.8708.2.27.2.2.1.1.50ColumnclientIfUnexpectedTxFrequencyread-onlycurrentThe actual frequency does not match the pre-configured frequency. A pre-configured frequency of '0' matches all actual frequencies. A: The configured frequency…
1.3.6.1.4.1.8708.2.27.2.2.1.1.51ColumnclientIfIllegalFrequencyread-onlycurrentThe frequency supported by the transceiver is not recognized by the system. A: Invalid or unknown frequency information is detected in the (pluggable) transcei…
1.3.6.1.4.1.8708.2.27.2.2.1.1.52ColumnclientIfLaserForcedOnread-writecurrentWhen enabled, the laser is on regardless of whether there is a trunc signal present or not. disabled - the laser is only on when there is a trunc signal. enabl…
1.3.6.1.4.1.8708.2.27.2.2.1.1.53ColumnclientIfTrxMediaread-createcurrentDefines the media and capability of the TRX.
1.3.6.1.4.1.8708.2.27.2.2.1.1.54ColumnclientIfTrxMediaMismatchread-onlycurrentThe TRX media does not match the expected one. A: Invalid or mismatching trx media is detected. D: The (pluggable) transceiver or board is replaced, or the con…
1.3.6.1.4.1.8708.2.27.2.2.1.1.55ColumnclientIfTruncAutoNegotiationModeread-writecurrentDecides whether auto negotiation shall be performed over the trunc connection. This is applicable when the terminating node at the other side of the trunc is c…
1.3.6.1.4.1.8708.2.27.2.2.1.1.56ColumnclientIfObjectPropertyread-onlycurrentProperty mask.
1.3.6.1.4.1.8708.2.27.2.2.1.1.57ColumnclientIfTxPowerLevelread-onlycurrentThe transmitted power level in units of 0.1 dBm.
1.3.6.1.4.1.8708.2.27.2.2.1.1.58ColumnclientIfLaserTempActualread-onlycurrentThe actual laser temperature in units of 0.1 degrees centigrade.
1.3.6.1.4.1.8708.2.27.2.2.1.1.59ColumnclientIfTraceIntrusionModeread-writecurrentIndicates whether the trace identifier should be inserted into the transmitted signal or to be transparent. disabled - The trace identifier is taken from the r…
1.3.6.1.4.1.8708.2.27.2.2.1.1.60ColumnclientIfTraceTransmittedread-writecurrentThe trace identifier to be transmitted from this interface. The identifier length is by default 0 to 15. For mxp8iiSonet board the length i 0 to 62. Set to emp…
1.3.6.1.4.1.8708.2.27.2.2.1.1.61ColumnclientIfTraceReceivedread-onlycurrentThe received trace identifier for this interface.
1.3.6.1.4.1.8708.2.27.2.2.1.1.62ColumnclientIfTraceExpectedread-writecurrentTrace identifier used for matching against the received trace identifier. The identifier length is by default 0 to 15. For mxp8iiSonet board the length is 0 to…
1.3.6.1.4.1.8708.2.27.2.2.1.1.63ColumnclientIfTraceAlarmModeread-writecurrentControls if the trace identifier mismatch alarm should be raised. disabled - The alarm is disabled. enabled - The alarm is raised if expected trace identifier …
1.3.6.1.4.1.8708.2.27.2.2.1.1.64ColumnclientIfTraceMismatchread-onlycurrentIndicates if the expected trace identifier differs from the received trace identifier. A: The received trace identifier differs from the expected trace identif…
1.3.6.1.4.1.8708.2.27.2.2.1.1.65ColumnclientIfNearEndLoopbackread-writecurrentLoop the client RX signal back to the client TX. This is also called Facility loopback disabled - the signal is not looped enabled - the signal is looped.
1.3.6.1.4.1.8708.2.27.2.2.1.1.66ColumnclientIfRxSignalStatusread-onlycurrentThe operational state for incoming (RX) signal of the interface. down - A major fault has occurred degraded - The signal quality is impaired. up - The signal i…
1.3.6.1.4.1.8708.2.27.2.2.1.1.67ColumnclientIfMsAlarmIndicationSignalC2Wread-onlycurrentMS Alarm indication signal (MS-AIS) on the client side. Applicable for SDH/Sonet signal formats. A: An 'all ones' pattern is detected. D: The signal is recover…
1.3.6.1.4.1.8708.2.27.2.2.1.1.68ColumnclientIfMsAlarmIndicationSignalW2Cread-onlycurrentMS Alarm indication signal (MS-AIS) on the trunc side. Applicable for SDH/Sonet/IWDM signal formats. A: An 'all ones' pattern is detected. D: The signal is rec…
1.3.6.1.4.1.8708.2.27.2.2.1.1.69ColumnclientIfRemoteDefectIndicationread-onlycurrentRemote defect indication. Applicable for SDH/Sonet signal formats. A: RDI indication (in SDH/Sonet frame) active. D: RDI indication inactive.
1.3.6.1.4.1.8708.2.27.2.2.1.1.70ColumnclientIfJ1TxTrailTraceread-writecurrentThe J1 trail trace identifier(s) to be transmitted for the VC4s/VC3s related to this interface, in the line signal (STM16/OC48). This parameter can be used in …
1.3.6.1.4.1.8708.2.27.2.2.1.1.71ColumnclientIfJ1TxTrailTraceInsertionModeread-writecurrentControls how the J1 trail trace insertion should work, i.e. how the j1TxTrailTrace parameter shall be inserted in the line signal. Important: there is only one…
1.3.6.1.4.1.8708.2.27.2.2.1.1.72ColumnclientIfTrxFailedread-onlycurrentA transceiver hardware failure is detected. A: The transceiver fails. D: The transceiver is replaced.
1.3.6.1.4.1.8708.2.27.2.2.1.1.73ColumnclientIfDisabledread-onlycurrentThe interface is disabled. A: Interface disabled. D: Interface enabled.
1.3.6.1.4.1.8708.2.27.2.2.1.1.74ColumnclientIfLoopbackread-onlycurrentThe interface is set in loopback mode. A: Loopback enabled. D: Loopback disabled.
1.3.6.1.4.1.8708.2.27.2.2.1.1.75ColumnclientIfVcGroupFailedW2Cread-onlycurrentThe received line signal contains a VC mapped to this interface, that is faulty, e.g. unequipped. Please note that this fault is in the LINE SIGNAL, but is pre…
1.3.6.1.4.1.8708.2.27.2.2.1.1.76ColumnclientIfReadJ1read-onlycurrentRead the received J1 for the VC4/VC3 in the STM16 frame associated to this interface. Synopsis: readJ1
1.3.6.1.4.1.8708.2.27.2.2.1.1.77ColumnclientIfClientSignalFailedread-onlycurrentThe received line signal contains a VC mapped to this interface, that is faulty, e.g. unequipped. Please note that this fault is in the LINE SIGNAL, but is pre…
1.3.6.1.4.1.8708.2.27.2.2.1.1.78ColumnclientIfAuLossOfPointerread-onlycurrentLoss of pointer.
1.3.6.1.4.1.8708.2.27.2.2.1.1.79ColumnclientIfGfpLossOfFrameread-onlycurrentGFP Loss of frame.
1.3.6.1.4.1.8708.2.27.2.2.1.1.80ColumnclientIfHighSpeedread-createcurrentThe expected signal bit rate in units of 1,000,000 bits (Mb) per second. If this object reports a value of 'n' then the speed of the interface is somewhere in …
1.3.6.1.4.1.8708.2.27.2.2.1.1.81ColumnclientIfActualFormatread-onlycurrentThe actual signal format.
1.3.6.1.4.1.8708.2.27.2.2.1.1.82ColumnclientIfRdiIntrusionModeread-onlycurrentIndicates whether RDI information should be inserted in the transmitted signal. disabled - No RDI information is inserted in the transmitted signal. enabled - …
1.3.6.1.4.1.8708.2.27.2.2.1.1.83ColumnclientIfMuxQuadVc4read-createcurrentStates which quadrant of the payload that the interface is connected to in rx direction. (outgoing line)
1.3.6.1.4.1.8708.2.27.2.2.1.1.84ColumnclientIfDemuxQuadVc4read-createcurrentStates whitch quadrant of the payload that the interface is connected to in tx direction. (outgoing client)
1.3.6.1.4.1.8708.2.27.2.2.1.1.85ColumnclientIfCcConnectionModeread-createcurrentcontrols if DemuxPayloadQuad is same as MuxPayloadQuad (same => connected, not same => disconnected)
1.3.6.1.4.1.8708.2.27.2.2.1.1.86ColumnclientIfCcConfigurationCommandread-onlycurrentCommand to change the crossconnect, If no arguments are given, the user will be prompted.
1.3.6.1.4.1.8708.2.27.2.2.1.1.87ColumnclientIfIllegalSignalFormatread-onlycurrentIllegalSignalFormat. A(ctivation): Actual Format does NOT match expected Format. D(e-activation): Actual Format does match expected Format.
1.3.6.1.4.1.8708.2.27.2.2.1.1.88ColumnclientIfSynchProtPortIdread-onlycurrentThe Id for this port in the synch prot group, to identify the port. (A or B)
1.3.6.1.4.1.8708.2.27.2.2.1.1.89ColumnclientIfSynchProtGroupMemberPortread-onlycurrentThe port number for the TX side of the port that is in this synch protection group.
1.3.6.1.4.1.8708.2.27.2.2.1.1.90ColumnclientIfSynchProtGroupStatusread-onlycurrentNote: This object is deprecated. The operational state for the protection group. bothDown - both sides down bothUp - both sides up ADownBUp - left side down, r…
1.3.6.1.4.1.8708.2.27.2.2.1.1.91ColumnclientIfSynchProtActivePortread-onlycurrentThe operational state for the protection group. none - no side is active. A - the A port is active. B - the B port is active.
1.3.6.1.4.1.8708.2.27.2.2.1.1.92ColumnclientIfSynchProtPortStatusread-onlycurrentThe operational synch protection state for this port in the synch protection group. down - this port is out of service. up - this port is active.
1.3.6.1.4.1.8708.2.27.2.2.1.1.93ColumnclientIfSynchProtToggleActivePortread-onlycurrentCommand to toggle which port is active in the synch prot group
1.3.6.1.4.1.8708.2.27.2.2.1.1.94ColumnclientIfNearEndLoopbackTimeoutread-createcurrentTimeout for near end loopback (a.k.a. facility loopback) to make sure connection to node is not lost if ppp link is broken. The unit is hours. 0.1 means 6 minu…
1.3.6.1.4.1.8708.2.27.2.2.1.1.95ColumnclientIfNearEndLoopbackEnabledread-onlycurrentNear end loopback (a.k.a. facility loopback) is enabled.
1.3.6.1.4.1.8708.2.27.2.2.1.1.96ColumnclientIfChangeNearEndLoopbackCommandread-onlycurrentCommand to change near end loopback (a.k.a. facility loopback) and loopbacktimeout
1.3.6.1.4.1.8708.2.27.2.2.1.1.97ColumnclientIfFarEndLoopbackEnabledread-onlycurrentFar end loopback (a.k.a. terminal loopback) is enabled.
1.3.6.1.4.1.8708.2.27.2.2.1.1.98ColumnclientIfFarEndLoopbackTimeoutread-createcurrentTimeout for far end loopback (a.k.a. terminal loopback) to make sure connection to node is not lost if ppp link is broken. The unit is hours. 0.1 means 6 minut…
1.3.6.1.4.1.8708.2.27.2.2.1.1.99ColumnclientIfChangeFarEndLoopbackCommandread-onlycurrentCommand to change far end loopback (a.k.a. terminal loopback) and loopbacktimeout
1.3.6.1.4.1.8708.2.27.2.2.1.1.100ColumnclientIfFormatNotSupportedByHwread-onlycurrentThe HW revision does not support the selected signal format.
1.3.6.1.4.1.8708.2.27.2.2.1.1.101ColumnclientIfLaserModeread-writecurrentThe administrative state of the TX-side laser. This is only used when signal format is ddgbeLine. on - The laser is turned on. als - Automatic Laser Shutdown/T…
1.3.6.1.4.1.8708.2.27.2.2.1.1.102ColumnclientIfAlarmIndicationSignalLineC2Wread-onlycurrentAlarm indication signal Line (AIS-L) on the client side. Applicable for Sonet signal formats. A: An 'all ones' Sonet signal is detected. D: Sonet signal recove…
1.3.6.1.4.1.8708.2.27.2.2.1.1.103ColumnclientIfFarEndClientFailureread-onlycurrentFailure on far end client.
1.3.6.1.4.1.8708.2.27.2.2.1.1.104ColumnclientIfOHTransparencyread-writecurrentThe 'OH Transparency' setting shall be set to 'off' for standard SDH/SONET mode. Does not work when client wrapper is enabled. When set to 'on', the following …
1.3.6.1.4.1.8708.2.27.2.2.1.1.105ColumnclientIfConnectedLineread-onlycurrentThe line ports that this client port is connected to.
1.3.6.1.4.1.8708.2.27.2.2.1.1.106ColumnclientIfForwardingErrorCorrectionModeread-writecurrentThe administrative state of the forwarding error correction function. disabled - FEC is disabled. enabled - FEC is activated. auto - autonegotiation is used to…
1.3.6.1.4.1.8708.2.27.2.2.1.1.107ColumnclientIfNoFrequencySetread-onlycurrentThe tunable laser frequency has not been set. A: Tunable laser frequency is not set. D: Tunable laser frequency is set.
1.3.6.1.4.1.8708.2.27.2.2.1.1.108ColumnclientIfJitterAttenuatorBWread-writecurrentDetermines the wander/jitter transfer bandwidth of the wander/jitter attenuator. With Option 1, the bandwidth is within 1 - 10 Hz, and with Option 2, the bandw…
1.3.6.1.4.1.8708.2.27.2.2.1.1.109ColumnclientIfConnectionStatusread-onlycurrentShows the name of the wdm port and possible subchannel/vc4 that it is connected to or Unconnected if not connected.
1.3.6.1.4.1.8708.2.27.2.2.1.1.110ColumnclientIfLoopFilterUnlockedread-onlycurrentThe loopfilter is unlocked. This is applicable for synchronous formats. A: Loopfilter is unlocked D: Loopfilter is locked
1.3.6.1.4.1.8708.2.27.2.2.1.1.111ColumnclientIfCableLengthread-writecurrentThe 'Cable length' is applicable for SONET mode (T1). The settings are for short haul (intra-building) T1 networks and will adjust the power of the transmitted…
1.3.6.1.4.1.8708.2.27.2.2.1.1.112ColumnclientIfConnectedForeignIndexread-writecurrentShows the index of the connected interface. Or 0 if unconnected.
1.3.6.1.4.1.8708.2.27.2.2.1.1.113ColumnclientIfDisconnectread-onlycurrentDisconnect existing crossConnections
1.3.6.1.4.1.8708.2.27.2.2.1.1.114ColumnclientIfOHTransparencyBitMaskread-createcurrentThe OH transparency bitmask. Bits: K1K2 = 0x01 E1E2 = 0x02 F1 = 0x04 D1-D3 = 0x08 D4-D12 = 0x10 B1 = 0x20 B2 = 0x40 E1 = 0x80 E2 = 0x100 J0 = 0x200
1.3.6.1.4.1.8708.2.27.2.2.1.1.115ColumnclientIfOHTransparencyStringread-onlycurrentOH transparency bytes tells if J0, rest of RSOH/Section OH and/or MSOH/Line OH are transparent or not. When RSOH/Section OH is set to transparent the bytes E1,…
1.3.6.1.4.1.8708.2.27.2.2.1.1.116ColumnclientIfOHTransparencySetread-onlycurrentSet which bytes that should be OH transparent
1.3.6.1.4.1.8708.2.27.2.2.1.1.117ColumnclientIfAuAlarmIndicationSignalC2Wread-onlycurrentAlarm indication signal (AIS) on the client-side. Applicable for SDH/Sonet signal formats. A: An 'all ones' SDH signal is detected. D: SDH signal recovered.
1.3.6.1.4.1.8708.2.27.2.2.1.1.118ColumnclientIfAuLossOfPointerC2Wread-onlycurrentLoss of pointer detected on the client-side. Applicable for SDH/Sonet signal formats. A: A loss of pointer is detected. D: SDH signal recovered.
1.3.6.1.4.1.8708.2.27.2.2.1.1.119ColumnclientIfAuLossOfPointerW2Cread-onlycurrentLoss of pointer detected on the line-side. Applicable for SDH/Sonet signal formats. A: A loss of pointer is detected. D: SDH signal recovered.
1.3.6.1.4.1.8708.2.27.2.2.1.1.120ColumnclientIfEthStandbyIndicatorread-onlycurrentShows if this port is in standby state. Used with hub protection.
1.3.6.1.4.1.8708.2.27.2.2.1.1.121ColumnclientIfAuAlarmIndicationSignalW2CSonetread-onlycurrentAlarm indication signal (AIS-P) on the line-side. A: An 'all ones' Sonet signal is detected. D: Sonet signal recovered.
1.3.6.1.4.1.8708.2.27.2.2.1.1.122ColumnclientIfAuAlarmIndicationSignalC2WSonetread-onlycurrentAlarm indication signal (AIS-P) on the client-side. A: An 'all ones' Sonet signal is detected. D: Sonet signal recovered.
1.3.6.1.4.1.8708.2.27.2.2.1.1.123ColumnclientIfAuLossOfPointerC2WSonetread-onlycurrentLoss of pointer detected on the client-side. A: A loss of pointer is detected. D: Sonet signal recovered.
1.3.6.1.4.1.8708.2.27.2.2.1.1.124ColumnclientIfAuLossOfPointerW2CSonetread-onlycurrentLoss of pointer detected on the line-side. A: A loss of pointer is detected. D: Sonet signal recovered.
1.3.6.1.4.1.8708.2.27.2.2.1.1.125ColumnclientIfTransceiverNoLoopbackread-onlycurrentThe inserted transceiver does not support the given loopback command.
1.3.6.1.4.1.8708.2.27.2.2.1.1.126ColumnclientIfFecFailureread-onlycurrentToo many errors to get valid FEC statistics. It is not possible to run control loops based on FEC statistics. A: Too many errors to get valid FEC statistics. D…
1.3.6.1.4.1.8708.2.27.2.2.1.1.127ColumnclientIfLaneAlignmentErrorread-onlycurrentIndicates whether multi-lane BASE-R PCS (Physical Coding Sublayer) has locked and aligned all received lanes. A: PCS receive lanes not locked and aligned. D: P…
1.3.6.1.4.1.8708.2.27.2.2.1.1.128ColumnclientIfFecCorrectedZerosread-onlycurrentThe number of corrected zeros.
1.3.6.1.4.1.8708.2.27.2.2.1.1.129ColumnclientIfFecCorrectedOnesread-onlycurrentThe number of corrected ones.
1.3.6.1.4.1.8708.2.27.2.2.1.1.130ColumnclientIfSignalDegradedread-onlycurrentToo many error corrected. If more errors are corrected it might effect the client signal in a negative way.
1.3.6.1.4.1.8708.2.27.2.2.1.1.131ColumnclientIfFecTyperead-writecurrentSet FEC scheme. disabled gFec according to ITU.T G.975 superFecI4 according to ITU-T G.975.1 superFecI7 according to ITU-T G.975.1 sdFec
1.3.6.1.4.1.8708.2.27.2.2.1.1.132ColumnclientIfSignalDegradeThresholdread-writecurrentThe alarm Signal Degraded shall be signalled when BER reaches a limit. The value will be affecting all ports. Predefined BER levels rxBerLevel1 = 1E-12 rxBerLe…
1.3.6.1.4.1.8708.2.27.2.2.1.1.133ColumnclientIfExpectedOpticalLayerMappingread-writecurrentThe expected optical layer mapping.
1.3.6.1.4.1.8708.2.27.2.2.1.1.134ColumnclientIfActualOpticalLayerMappingread-onlycurrentThe actual optical layer mapping.
1.3.6.1.4.1.8708.2.27.2.2.1.1.135ColumnclientIfConfigurationMismatchread-onlycurrentThe inserted transceiver does not support the configuration of the optical layer mapping. A: A transceiver with other supported optical layer mapping than the …
1.3.6.1.4.1.8708.2.27.2.2.1.1.136ColumnclientIfChromaticDispersionread-onlycurrentReceived chromatic dispersion that describe the spreading of a light pulse as it travels down a fiber when light pulses launched close together.
1.3.6.1.4.1.8708.2.27.2.2.1.1.137ColumnclientIfDifferentialGroupDelayread-onlycurrentThe arrival time difference between two polarization states at the output of the media (fiber).
1.3.6.1.4.1.8708.2.27.2.2.1.1.138ColumnclientIfTxStateread-onlycurrentThe operational state of the transiver for outgoing (TX) signal. - Init started - Init ready - Data path locked - Laser ready off - Laser ready - Laser bias re…
1.3.6.1.4.1.8708.2.27.2.2.1.1.139ColumnclientIfRxStateread-onlycurrentThe operational state of the transiver for outgoing (RX) signal. - Init started - Init ready - Frequency ready - Input signal received - A/D Converter ready - …
1.3.6.1.4.1.8708.2.27.2.2.1.1.140ColumnclientIfIdxread-createcurrentInternal object reference
1.3.6.1.4.1.8708.2.27.2.2.1.1.141ColumnclientIfIfNoread-createcurrentThe physical interface number of the actual multi-connector port.
1.3.6.1.4.1.8708.2.27.2.2.1.1.142ColumnclientIfIdxIfread-createcurrentInternal object reference of the actual multi-connector port.
1.3.6.1.4.1.8708.2.27.2.2.1.1.143ColumnclientIfUpPortIdread-onlycurrentInternal port reference for traffic unit.
1.3.6.1.4.1.8708.2.27.2.2.1.1.144ColumnclientIfNoOfLanesread-createcurrentNumber of lanes on port
1.3.6.1.4.1.8708.2.27.2.2.1.1.145ColumnclientIfFecCorrectedBitsread-onlycurrentFEC counter. Number of corrected bits
1.3.6.1.4.1.8708.2.27.2.2.1.1.146ColumnclientIfOSNRMarginread-onlycurrentOptical signal-to-noise ratio margin (dB/0.1nm), based on calculation from rate of corrected bits.
1.3.6.1.4.1.8708.2.27.2.2.1.1.147ColumnclientIfExpectedPhysicalLayerMappingread-writecurrentThe expected physical layer mapping.
1.3.6.1.4.1.8708.2.27.2.2.1.1.148ColumnclientIfSignalDirectionread-onlycurrentIndicates the direction of the signal. rx - Inbound direction tx - Outbound direction biDir - Bidirectional txRx - Both Tx and Rx
1.3.6.1.4.1.8708.2.27.2.2.1.1.149ColumnclientIfAidread-onlycurrentThe access identifier (AID) of the interface. The format is according to GR-833.
1.3.6.1.4.1.8708.2.27.2.2.1.1.150ColumnclientIfPhysicalLocationread-onlycurrentThe physical location of the if. The format is according to GR-833.
1.3.6.1.4.1.8708.2.27.2.2.1.1.151ColumnclientIfTrxCommunicationFailureread-onlycurrentThe board is unable to communicate with the transceiver. alarm: Protocol errors detected on the transceiver control link. ok: No communication errors detected …
1.3.6.1.4.1.8708.2.27.2.2.1.1.152ColumnclientIfTribPortIdread-onlycurrentTributary port id.
1.3.6.1.4.1.8708.2.27.2.2.1.1.153ColumnclientIfIfTyperead-writecurrentType of interface (Individual or bundled).
1.3.6.1.4.1.8708.2.27.2.2.1.1.154ColumnclientIfConfigurationCommandSNMPread-onlycurrentCommand to change the signal format, and, if applicable, also the mode (framed, transparent) via SNMP.
1.3.6.1.4.1.8708.2.27.2.2.1.1.155ColumnclientIfTrxPowerOutOfRangeread-onlycurrentThe power classification of the transceiver exceeds the design limit of the board. alarm: A transceiver with a power classification that exceeds the design lim…
1.3.6.1.4.1.8708.2.27.2.3NodeclientVc4List
1.3.6.1.4.1.8708.2.27.2.3.1TableclientVc4Tablenot-accessiblecurrentThe interface list.
1.3.6.1.4.1.8708.2.27.2.3.1.1RowclientVc4Entrynot-accessiblecurrentAn entry in the interface list.
1.3.6.1.4.1.8708.2.27.2.3.1.1.1ColumnclientVc4Indexread-onlycurrentAn arbitrary index assigned to each if entry.
1.3.6.1.4.1.8708.2.27.2.3.1.1.2ColumnclientVc4Nameread-onlycurrentThe management name of the vc4, e.g. vc4:1:2:1-2:8 where the first number indicates sub-rack, the second slot number and the third/forth are the port numbers. …
1.3.6.1.4.1.8708.2.27.2.3.1.1.3ColumnclientVc4Descrread-writecurrentUser configurable label.
1.3.6.1.4.1.8708.2.27.2.3.1.1.4ColumnclientVc4Subrackread-onlycurrentThe number of the subrack where the vc4 is located.
1.3.6.1.4.1.8708.2.27.2.3.1.1.5ColumnclientVc4Slotread-onlycurrentThe number of the slot where the vc4 is located.
1.3.6.1.4.1.8708.2.27.2.3.1.1.6ColumnclientVc4TxPortread-onlycurrentThe number of the port where the TX-side of the vc4 is located.
1.3.6.1.4.1.8708.2.27.2.3.1.1.7ColumnclientVc4RxPortread-onlycurrentThe number of the port where the RX-side of the vc4 is located.
1.3.6.1.4.1.8708.2.27.2.3.1.1.8ColumnclientVc4Vc4read-onlycurrentThe id of the vc4/STS3/STS1 within the STM16/OC192 frame.
1.3.6.1.4.1.8708.2.27.2.3.1.1.9ColumnclientVc4ObjectPropertyread-onlycurrentProperty mask.
1.3.6.1.4.1.8708.2.27.2.3.1.1.10ColumnclientVc4AuAlarmIndicationSignalread-onlycurrentAlarm indication signal (AIS). Applicable for SDH/Sonet signal formats. A: An 'all ones' SDH/Sonet signal is detected. D: SDH/Sonet signal recovered.
1.3.6.1.4.1.8708.2.27.2.3.1.1.11ColumnclientVc4AuLossOfPointerread-onlycurrentLoss of pointer detected. Applicable for SDH/Sonet signal formats. A: A loss of pointer is detected. D: SDH/Sonet signal recovered.
1.3.6.1.4.1.8708.2.27.2.3.1.1.12ColumnclientVc4RxSignalStatusread-onlycurrentThe operational state for incoming (RX) signal of the interface. down - A fault that would lead to a protection switch has occurred. degraded - The signal qual…
1.3.6.1.4.1.8708.2.27.2.3.1.1.13ColumnclientVc4ConcatenationStatusread-onlycurrentDescribes if and how the VC4s are concatenated. on - Concatenation is used. off - No concatenation is used. can be vc3 (STS-1), vc4 (STS-3, STM1/OC3), vc4x4c (…
1.3.6.1.4.1.8708.2.27.2.3.1.1.14ColumnclientVc4PayloadStatusread-onlycurrentDescribes if the VC4/STS3 contains payload. equipped - VC4/STS3 contains payload. unequipped - No payload in VC4/STS3.
1.3.6.1.4.1.8708.2.27.2.3.1.1.15ColumnclientVc4ConnectionStatusread-onlycurrentShows the name of the client port and possible subchannel/vc4 that it is connected to or Unconnected if not connected.
1.3.6.1.4.1.8708.2.27.2.4NodelumentisClientNotifications
1.3.6.1.4.1.8708.2.27.2.4.0NodeclientNotifyPrefix
1.3.6.1.4.1.8708.2.27.2.4.0.1NotificationclientIfTxSignalStatusDowncurrentSent when the signal status attribute of an interface changes.
1.3.6.1.4.1.8708.2.27.2.4.0.2NotificationclientIfTxSignalStatusUpcurrentSent when the signal status attribute of an interface changes.
1.3.6.1.4.1.8708.2.27.2.4.0.3NotificationclientIfTxSignalStatusDegradedcurrentSent when the signal status attribute of an interface changes.
1.3.6.1.4.1.8708.2.27.2.5NodeclientLanesList
1.3.6.1.4.1.8708.2.27.2.5.1TableclientLanesTablenot-accessiblecurrentThe interface list.
1.3.6.1.4.1.8708.2.27.2.5.1.1RowclientLanesEntrynot-accessiblecurrentAn entry in the interface list.
1.3.6.1.4.1.8708.2.27.2.5.1.1.1ColumnclientLanesIndexread-createcurrentAn arbitrary index assigned to each if entry.
1.3.6.1.4.1.8708.2.27.2.5.1.1.2ColumnclientLanesNameread-createcurrentThe management name of the Lanes, e.g. Lane:1:2:1:4 where the first number indicates sub-rack, the second slot number and the third is the interface number. Th…
1.3.6.1.4.1.8708.2.27.2.5.1.1.3ColumnclientLanesSubrackread-createcurrentThe number of the subrack where the lane is located.
1.3.6.1.4.1.8708.2.27.2.5.1.1.4ColumnclientLanesSlotread-createcurrentThe number of the slot where the lane is located.
1.3.6.1.4.1.8708.2.27.2.5.1.1.5ColumnclientLanesTxPortread-createcurrentThe number of the port where the TX-side of the lane is located.
1.3.6.1.4.1.8708.2.27.2.5.1.1.6ColumnclientLanesRxPortread-createcurrentThe number of the port where the RX-side of the lane is located.
1.3.6.1.4.1.8708.2.27.2.5.1.1.7ColumnclientLanesLaneIdread-createcurrentThe id of the lane within the Client frame.
1.3.6.1.4.1.8708.2.27.2.5.1.1.8ColumnclientLanesRxPowerLevelread-onlycurrentThe received power level in units of 0.1 dBm.
1.3.6.1.4.1.8708.2.27.2.5.1.1.9ColumnclientLanesWaveLengthread-onlycurrentThe wavelength/frequency associated with the lane. ch871 means the frequency 187.1 THz. w1310 means the wavelength 1310 nm. undefined if no wavelength is appli…
1.3.6.1.4.1.8708.2.27.2.5.1.1.10ColumnclientLanesBEread-onlycurrentThe counter associated with the number of Bit Interleave Parity errors in a particular lane.
1.3.6.1.4.1.8708.2.27.2.5.1.1.11ColumnclientLanesResetBEread-writecurrentCommand to reset the BIP-8 error counter value.
1.3.6.1.4.1.8708.2.27.2.5.1.1.12ColumnclientLanesLossOfSignalread-onlycurrentLoss of signal. Applicable for all signal formats. A(ctivation): Active loss of signal HW indication. D(e-activation): Inactive loss of signal HW indication.
1.3.6.1.4.1.8708.2.27.2.5.1.1.13ColumnclientLanesObjectPropertyread-onlycurrentProperty mask.
1.3.6.1.4.1.8708.2.27.2.5.1.1.14ColumnclientLanesLossOfSyncread-onlycurrentLoss of sync. All forms of sync loss. A(ctivation): GbE 'frame' can not be located. D(e-activation): GbE 'frame' is located.
1.3.6.1.4.1.8708.2.27.2.5.1.1.15ColumnclientLanesLocalLinkFaultread-onlycurrentLocal link fault. IEEE 802.3ah A(ctivation): Active local link fault indication. D(e-activation): Inactive local link fault indication.
1.3.6.1.4.1.8708.2.27.2.5.1.1.16ColumnclientLanesRemoteLinkFaultread-onlycurrentRemote link fault. IEEE 802.3ah A(ctivation): Active remote link fault indication. D(e-activation): Inactive remote link fault indication.
1.3.6.1.4.1.8708.2.27.2.5.1.1.17ColumnclientLanesHighBitErrorRateread-onlycurrentHigh bit error rate (Hi-Ber). IEEE 802.3ah A(ctivation): Active high bit error rate. D(e-activation): Inactive high bit error rate.
1.3.6.1.4.1.8708.2.27.2.5.1.1.18ColumnclientLanesReceiverSensitivityread-onlycurrentThe lowest power that the receiver is guaranteed to handle, in units of 0.1 dBm.
1.3.6.1.4.1.8708.2.27.2.5.1.1.19ColumnclientLanesReceivedPowerLowread-onlycurrentReceived power level low threshold exceeded. Relative to the threshold in the port interface table. Applicable for all signal formats. alarm: The received powe…
1.3.6.1.4.1.8708.2.27.2.5.1.1.20ColumnclientLanesIfNoread-createcurrentThe physical interface number.
1.3.6.1.4.1.8708.2.27.2.5.1.1.21ColumnclientLanesIdxread-createcurrentInternal object reference
1.3.6.1.4.1.8708.2.27.2.5.1.1.22ColumnclientLanesClientIfIdxread-createcurrentInternal object reference of the clientIf
1.3.6.1.4.1.8708.2.27.2.5.1.1.23ColumnclientLanesAdminStatusread-writecurrentThe administrative state for the interface. down - The interface is de-activated. service - The interface is activated but alarms are suppressed. Intended for …
1.3.6.1.4.1.8708.2.27.2.5.1.1.24ColumnclientLanesOperStatusread-onlycurrentThe operational state for the interface. notPresent - The physical resources are not available. down - The interface is de-activated or there are faults preven…
1.3.6.1.4.1.8708.2.27.2.5.1.1.25ColumnclientLanesUpPortIdread-onlycurrentInternal port reference for traffic unit.
1.3.6.1.4.1.8708.2.27.2.6NodeclientMpoLanesList
1.3.6.1.4.1.8708.2.27.2.6.1TableclientMpoLanesTablenot-accessiblecurrentThe interface list.
1.3.6.1.4.1.8708.2.27.2.6.1.1RowclientMpoLanesEntrynot-accessiblecurrentAn entry in the interface list.
1.3.6.1.4.1.8708.2.27.2.6.1.1.1ColumnclientMpoLanesIndexread-createcurrentAn arbitrary index assigned to each if entry.
1.3.6.1.4.1.8708.2.27.2.6.1.1.2ColumnclientMpoLanesNameread-createcurrentThe management name of the Lanes, e.g. Lane:1:2:1:4 where the first number indicates sub-rack, the second slot number and the third is the interface number. Th…
1.3.6.1.4.1.8708.2.27.2.6.1.1.3ColumnclientMpoLanesSubrackread-createcurrentThe number of the subrack where the lane is located.
1.3.6.1.4.1.8708.2.27.2.6.1.1.4ColumnclientMpoLanesSlotread-createcurrentThe number of the slot where the lane is located.
1.3.6.1.4.1.8708.2.27.2.6.1.1.5ColumnclientMpoLanesIfNoread-createcurrentThe physical interface number.
1.3.6.1.4.1.8708.2.27.2.6.1.1.6ColumnclientMpoLanesLaneIdread-createcurrentThe identity of the lane within the Client frame.
1.3.6.1.4.1.8708.2.27.2.6.1.1.7ColumnclientMpoLanesAdminStatusread-writecurrentThe administrative state for the interface. down - The interface is de-activated. service - The interface is activated but alarms are suppressed. Intended for …
1.3.6.1.4.1.8708.2.27.2.6.1.1.8ColumnclientMpoLanesOperStatusread-onlycurrentThe operational state for the interface. notPresent - The physical resources are not available. down - The interface is de-activated or there are faults preven…
1.3.6.1.4.1.8708.2.27.2.6.1.1.9ColumnclientMpoLanesLaserStatusread-onlycurrentThe operational state of the laser. off - The laser is turned off. on - The laser is turned on.
1.3.6.1.4.1.8708.2.27.2.6.1.1.10ColumnclientMpoLanesRxSensitivityread-onlycurrentThe lowest power that the receiver is guaranteed to handle, in units of 0.1 dBm.
1.3.6.1.4.1.8708.2.27.2.6.1.1.11ColumnclientMpoLanesRxPowerLevelread-onlycurrentThe received power level in units of 0.1 dBm.
1.3.6.1.4.1.8708.2.27.2.6.1.1.12ColumnclientMpoLanesPowerLevelLowRelativeThresholdread-writecurrentThe lower threshold for received power level in units of 0.1 dB, relative to the receiver sensitivity.
1.3.6.1.4.1.8708.2.27.2.6.1.1.13ColumnclientMpoLanesWaveLengthread-onlycurrentThe wavelength/frequency associated with the lane. ch871 means the frequency 187.1 THz. w1310 means the wavelength 1310 nm. undefined if no wavelength is appli…
1.3.6.1.4.1.8708.2.27.2.6.1.1.14ColumnclientMpoLanesObjectPropertyread-onlycurrentProperty mask.
1.3.6.1.4.1.8708.2.27.2.6.1.1.15ColumnclientMpoLanesForwardAlsread-writecurrentForward Automatic Laser Shut-down. Decides if laser shutdown of the client should occur when a defect on the line or remote client is detected. disabled - The …
1.3.6.1.4.1.8708.2.27.2.6.1.1.16ColumnclientMpoLanesLossOfSignalread-onlycurrentLoss of signal. Applicable for all signal formats. A(ctivation): Active loss of signal HW indication. D(e-activation): Inactive loss of signal HW indication.
1.3.6.1.4.1.8708.2.27.2.6.1.1.17ColumnclientMpoLanesRxPowerLowread-onlycurrentReceived power level low threshold exceeded. Relative to the threshold in the port interface table. Applicable for all signal formats. alarm: The received powe…