LUM-IFIWDM-MIB
69 objects
The MIB module the new iWDM mib. iWDM is a proprietary line format of Infinera. Similar to SDH it has two layers of overhead: iWDM regenerator section OH (iWDM-rs) and iWDM multiplex section OH (iWDM-ms). The management plane aspects of those two layers are specified in this MIB. The tables contained in this MIB are: (1) The General group contains some general attributes as time stamps and tables sizes. (2) The iWDM regenerator (iWDM-rs) group contains information and configuration for the regenerator section overhead. (3) The iWDM multiplexing (iWDM-ms) group contains information and configuration for the multiplexing overhead.
Imported Objects
| LUM-REG | lumIfIwdmMIB lumModules |
| LUM-TC | DisplayStringWithNA EnabledDisabledWithNA FaultStatusWithNA MgmtNameString SignalFormat SignalStatusWithNA Unsigned32WithNA |
| SNMPv2-CONF | MODULE-COMPLIANCE OBJECT-GROUP |
| SNMPv2-SMI | MODULE-IDENTITY OBJECT-TYPE Unsigned32 |
| SNMPv2-TC | DateAndTime |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.8708.1.1.63 | IdentitylumIfIwdmMIBModule | The MIB module the new iWDM mib. iWDM is a proprietary line format of Infinera. Similar to SDH it has two layers of overhead: iWDM regenerator section OH (iWDM… | ||
| 1.3.6.1.4.1.8708.2.63.1 | NodelumIfIwdmConfs | |||
| 1.3.6.1.4.1.8708.2.63.1.1 | NodelumIfIwdmGroups | |||
| 1.3.6.1.4.1.8708.2.63.1.1.1 | GroupifIwdmGeneralGroupV1 | deprecated | The general objects. | |
| 1.3.6.1.4.1.8708.2.63.1.1.2 | GroupifIwdmGeneralGroupV2 | current | The general objects. | |
| 1.3.6.1.4.1.8708.2.63.1.1.3 | GroupifIwdmRsGroupV1 | deprecated | The ifIwdm RS objects (R26.0). | |
| 1.3.6.1.4.1.8708.2.63.1.1.4 | GroupifIwdmMsGroupV1 | deprecated | The ifIwdm MS objects (R26.0). | |
| 1.3.6.1.4.1.8708.2.63.1.1.5 | GroupifIwdmRsGroupV2 | deprecated | The ifIwdm RS objects (R27.0). | |
| 1.3.6.1.4.1.8708.2.63.1.1.6 | GroupifIwdmMsGroupV2 | deprecated | The ifIwdm MS objects (R27.0). | |
| 1.3.6.1.4.1.8708.2.63.1.1.7 | GroupifIwdmRsGroupV3 | current | The ifIwdm RS objects (R27.1). | |
| 1.3.6.1.4.1.8708.2.63.1.1.8 | GroupifIwdmMsGroupV3 | current | The ifIwdm MS objects (R27.1). | |
| 1.3.6.1.4.1.8708.2.63.1.1.9 | GroupifIwdmPathGroupV1 | current | The path objects. | |
| 1.3.6.1.4.1.8708.2.63.1.2 | NodelumIfIwdmCompl | |||
| 1.3.6.1.4.1.8708.2.63.1.2.1 | CompliancelumIfIwdmComplV1 | deprecated | Basic implementation requirements for the ifIwdm MIB. (R26.0) | |
| 1.3.6.1.4.1.8708.2.63.1.2.2 | CompliancelumIfIwdmComplV2 | deprecated | Basic implementation requirements for the ifIwdm MIB. (R27.0) | |
| 1.3.6.1.4.1.8708.2.63.1.2.3 | CompliancelumIfIwdmComplV3 | current | Basic implementation requirements for the ifIwdm MIB. (R27.1) | |
| 1.3.6.1.4.1.8708.2.63.2 | NodelumIfIwdmMIBObjects | |||
| 1.3.6.1.4.1.8708.2.63.2.1 | NodeifIwdmGeneral | |||
| 1.3.6.1.4.1.8708.2.63.2.1.1 | ScalarifIwdmGeneralConfigLastChangeTime | read-only | current | The time when the configuration of the MIB was last changed. |
| 1.3.6.1.4.1.8708.2.63.2.1.2 | ScalarifIwdmGeneralStateLastChangeTime | read-only | current | The time when the state and/or configuration of the MIB was last changed. |
| 1.3.6.1.4.1.8708.2.63.2.1.3 | ScalarifIwdmGeneralIfIwdmRsTableSize | read-only | current | Size of rs table. |
| 1.3.6.1.4.1.8708.2.63.2.1.4 | ScalarifIwdmGeneralIfIwdmRsConfigLastChangeTime | read-only | current | The time when the configuration of the table was last changed. |
| 1.3.6.1.4.1.8708.2.63.2.1.5 | ScalarifIwdmGeneralIfIwdmRsStateLastChangeTime | read-only | current | The time when the state and/or configuration of the table was last changed. |
| 1.3.6.1.4.1.8708.2.63.2.1.6 | ScalarifIwdmGeneralIfIwdmMsTableSize | read-only | current | Size of ms table |
| 1.3.6.1.4.1.8708.2.63.2.1.7 | ScalarifIwdmGeneralIfIwdmMsConfigLastChangeTime | read-only | current | The time when the configuration of the table was last changed. |
| 1.3.6.1.4.1.8708.2.63.2.1.8 | ScalarifIwdmGeneralIfIwdmMsStateLastChangeTime | read-only | current | The time when the state and/or configuration of the table was last changed. |
| 1.3.6.1.4.1.8708.2.63.2.1.9 | ScalarifIwdmGeneralIfIwdmPathTableSize | read-only | current | Size of path table. |
| 1.3.6.1.4.1.8708.2.63.2.1.10 | ScalarifIwdmGeneralIfIwdmPathConfigLastChangeTime | read-only | current | The time when the configuration of the table was last changed. |
| 1.3.6.1.4.1.8708.2.63.2.1.11 | ScalarifIwdmGeneralIfIwdmPathStateLastChangeTime | read-only | current | The time when the state and/or configuration of the table was last changed. |
| 1.3.6.1.4.1.8708.2.63.2.2 | NodeifIwdmRsList | |||
| 1.3.6.1.4.1.8708.2.63.2.2.1 | TableifIwdmRsTable | not-accessible | current | The regenerator (iWDM-rs) group contains information and configuration for the iWDM regenerator section (iWDM-rs). |
| 1.3.6.1.4.1.8708.2.63.2.2.1.1 | RowifIwdmRsEntry | not-accessible | current | An entry in the ifIwdm rs list. |
| 1.3.6.1.4.1.8708.2.63.2.2.1.1.1 | ColumnifIwdmRsIndex | read-only | current | An index assigned to each entry. |
| 1.3.6.1.4.1.8708.2.63.2.2.1.1.2 | ColumnifIwdmRsName | read-only | current | The management name of the iWDM Rs, for example 'rs:1:2:1-2', where the first number indicates subrack, the second slot number and the third/fourth are the phy… |
| 1.3.6.1.4.1.8708.2.63.2.2.1.1.3 | ColumnifIwdmRsTraceTransmitted | read-write | current | The operator specific trace identifier to be transmitted from this interface. The trace identifier length is by default 0 to 63. For tpmrHL16G board only the l… |
| 1.3.6.1.4.1.8708.2.63.2.2.1.1.4 | ColumnifIwdmRsTraceReceived | read-only | current | The received operator specific trace identifier for this interface. The trace _notApplicable_ is used to tell SNMP clients that this attribute is not used in c… |
| 1.3.6.1.4.1.8708.2.63.2.2.1.1.5 | ColumnifIwdmRsTraceExpected | read-write | current | Trace identifier used for matching against the received trace identifier. The trace identifier length is by default 0 to 63. For tpmrHL16G board only the lengt… |
| 1.3.6.1.4.1.8708.2.63.2.2.1.1.6 | ColumnifIwdmRsTraceAlarmMode | read-only | current | Controls if the trace identifier mismatch alarm should be raised. disabled - The alarm is disabled. enabled - The alarm is raised if expected trace identifier … |
| 1.3.6.1.4.1.8708.2.63.2.2.1.1.7 | ColumnifIwdmRsTraceTraceMismatch | read-only | current | Trace identifier mismatch. Indicates if the expected trace identifier differs from the received trace identifier. Alarm: The received trace identifier differs … |
| 1.3.6.1.4.1.8708.2.63.2.2.1.1.8 | ColumnifIwdmRsUpId | read-only | current | Identity in the UP for the iwdmRs entry in the traffic unit |
| 1.3.6.1.4.1.8708.2.63.2.2.1.1.9 | ColumnifIwdmRsLossOfFrame | read-only | current | Loss of frame (LOF). Alarm: An iWDM frame cannot be located. OK: An iWDM frame can be located. |
| 1.3.6.1.4.1.8708.2.63.2.2.1.1.10 | ColumnifIwdmRsConnIfBasicIfIndex | read-only | current | An index describing to which index in ifBasicIf table this object is related to. |
| 1.3.6.1.4.1.8708.2.63.2.2.1.1.11 | ColumnifIwdmRsTxSignalStatus | read-only | current | The state for outgoing (Tx) signal of the interface. down - A major fault has occurred. degraded - The signal quality is impaired. up - The signal is OK. |
| 1.3.6.1.4.1.8708.2.63.2.2.1.1.12 | ColumnifIwdmRsRxSignalStatus | read-only | current | The state for incoming (Rx) signal of the interface. down - A major fault has occurred. degraded - The signal quality is impaired. up - The signal is OK. |
| 1.3.6.1.4.1.8708.2.63.2.2.1.1.13 | ColumnifIwdmRsRate | read-only | current | Rate |
| 1.3.6.1.4.1.8708.2.63.2.3 | NodeifIwdmMsList | |||
| 1.3.6.1.4.1.8708.2.63.2.3.1 | TableifIwdmMsTable | not-accessible | current | The multiplexing (iWDM-ms) group contains information and configuration for the iWDM multiplexing section (iWDM-ms). |
| 1.3.6.1.4.1.8708.2.63.2.3.1.1 | RowifIwdmMsEntry | not-accessible | current | An entry in the ifIwdm ms list. |
| 1.3.6.1.4.1.8708.2.63.2.3.1.1.1 | ColumnifIwdmMsIndex | read-only | current | An index assigned to each entry. |
| 1.3.6.1.4.1.8708.2.63.2.3.1.1.2 | ColumnifIwdmMsName | read-only | current | The management name of the iWDM Ms, for example 'ms:1:2:1-2', where the first number indicates subrack, the second slot number and the third/fourth are the phy… |
| 1.3.6.1.4.1.8708.2.63.2.3.1.1.3 | ColumnifIwdmMsAlarmIndicationSignal | read-only | current | Alarm indication signal (AIS). Alarm: An 'all ones' pattern is detected. OK: The signal recovered. |
| 1.3.6.1.4.1.8708.2.63.2.3.1.1.4 | ColumnifIwdmMsBackwardDefectIndication | read-only | current | Backward defect indication (BDI). Indicates if backward defect indication (BDI) alarm exists or not. Alarm: Backward defect indication (in wrapper) active. OK:… |
| 1.3.6.1.4.1.8708.2.63.2.3.1.1.5 | ColumnifIwdmMsUpId | read-only | current | Identity in the UP for the iwdmMs entry in the traffic unit |
| 1.3.6.1.4.1.8708.2.63.2.3.1.1.6 | ColumnifIwdmMsConnIfBasicIfIndex | read-only | current | An index describing to which index in ifBasicIf table this object is related to. |
| 1.3.6.1.4.1.8708.2.63.2.3.1.1.7 | ColumnifIwdmMsTxSignalStatus | read-only | current | The state for outgoing (Tx) signal of the interface. down - A major fault has occurred. degraded - The signal quality is impaired. up - The signal is OK. |
| 1.3.6.1.4.1.8708.2.63.2.3.1.1.8 | ColumnifIwdmMsRxSignalStatus | read-only | current | The state for incoming (Rx) signal of the interface. down - A major fault has occurred. degraded - The signal quality is impaired. up - The signal is OK. |
| 1.3.6.1.4.1.8708.2.63.2.3.1.1.9 | ColumnifIwdmMsRate | read-only | current | Rate |
| 1.3.6.1.4.1.8708.2.63.2.4 | NodeifIwdmPathList | |||
| 1.3.6.1.4.1.8708.2.63.2.4.1 | TableifIwdmPathTable | not-accessible | current | The path (iWDM-path) group contains information and configuration for the iWDM path section (iWDM-path). |
| 1.3.6.1.4.1.8708.2.63.2.4.1.1 | RowifIwdmPathEntry | not-accessible | current | An entry in the ifIwdm path list. |
| 1.3.6.1.4.1.8708.2.63.2.4.1.1.1 | ColumnifIwdmPathIndex | read-only | current | An index assigned to each entry. |
| 1.3.6.1.4.1.8708.2.63.2.4.1.1.2 | ColumnifIwdmPathName | read-only | current | The management name of the iWDM path, for example 'path:1:2:1-2', where the first number indicates subrack, the second slot number and the third/fourth are the… |
| 1.3.6.1.4.1.8708.2.63.2.4.1.1.3 | ColumnifIwdmPathBackwardDefectIndication | read-only | current | Backward defect indication (BDI). Indicates if backward defect indication (BDI) alarm exists or not. Alarm: Backward defect indication (in wrapper) active. OK:… |
| 1.3.6.1.4.1.8708.2.63.2.4.1.1.4 | ColumnifIwdmPathClientSignalFailure | read-only | current | Client signal failure. |
| 1.3.6.1.4.1.8708.2.63.2.4.1.1.5 | ColumnifIwdmPathUId | read-only | current | Unique identity for the iwdmPath entry in the traffic unit |
| 1.3.6.1.4.1.8708.2.63.2.4.1.1.6 | ColumnifIwdmPathConnIfBasicIfIndex | read-only | current | An index describing to which index in ifBasicIf table this object is related to. |
| 1.3.6.1.4.1.8708.2.63.2.4.1.1.7 | ColumnifIwdmPathTxSignalStatus | read-only | current | The state for outgoing (Tx) signal of the interface. down - A major fault has occurred. degraded - The signal quality is impaired. up - The signal is OK. |
| 1.3.6.1.4.1.8708.2.63.2.4.1.1.8 | ColumnifIwdmPathRxSignalStatus | read-only | current | The state for incoming (Rx) signal of the interface. down - A major fault has occurred. degraded - The signal quality is impaired. up - The signal is OK. |
| 1.3.6.1.4.1.8708.2.63.2.4.1.1.9 | ColumnifIwdmPathRate | read-only | current | Rate |