MIB Viewer

LUM-IFSDH-MIB

52 objects
The MIB module for management of sdh parameters on port objects. This module describes the regenerator and multiplexing sections in ITU G.707 Recommendation. References are referring to G.707 (12/2003), G.783 (03/206) The tables contained in this MIB are: (1) The General group contains some general attributes as time stamps and tables sizes. (2) The regenerator (rs) group contains information and configuration for the regenerator section overhead. (3) The multiplexing (ms) group contains information and configuration for the multiplexing overhead.
Imported Objects
LUM-REGlumIfSdhMIB lumModules
LUM-TCDisplayStringWithNA EnabledDisabledWithNA FaultStatusWithNA MgmtNameString SignalStatusWithNA Unsigned32WithNA
SNMPv2-CONFMODULE-COMPLIANCE OBJECT-GROUP
SNMPv2-SMIMODULE-IDENTITY OBJECT-TYPE Unsigned32
SNMPv2-TCDateAndTime
OIDNameAccessStatusDescription
1.3.6.1.4.1.8708.1.1.52IdentitylumIfSdhMIBModuleThe MIB module for management of sdh parameters on port objects. This module describes the regenerator and multiplexing sections in ITU G.707 Recommendation. R…
1.3.6.1.4.1.8708.2.52.1NodelumIfSdhConfs
1.3.6.1.4.1.8708.2.52.1.1NodelumIfSdhGroups
1.3.6.1.4.1.8708.2.52.1.1.1GroupifSdhGeneralGroupV1currentThe general objects.
1.3.6.1.4.1.8708.2.52.1.1.2GroupifSdhRsGroupV1deprecatedThe ifSdh RS objects (R20.0).
1.3.6.1.4.1.8708.2.52.1.1.3GroupifSdhMsGroupV1deprecatedThe ifSdh MS objects (R20.0).
1.3.6.1.4.1.8708.2.52.1.1.4GroupifSdhMsGroupV2currentThe ifSdh MS objects (R24.0).
1.3.6.1.4.1.8708.2.52.1.1.5GroupifSdhRsGroupV2currentThe ifSdh RS objects (R24.0).
1.3.6.1.4.1.8708.2.52.1.2NodelumIfSdhCompl
1.3.6.1.4.1.8708.2.52.1.2.1CompliancelumIfSdhComplV1deprecatedBasic implementation requirements for the ifSdh MIB. (R20.0)
1.3.6.1.4.1.8708.2.52.1.2.2CompliancelumIfSdhComplV2deprecatedBasic implementation requirements for the ifSdh MIB. (R24.0)
1.3.6.1.4.1.8708.2.52.1.2.3CompliancelumIfSdhComplV3currentBasic implementation requirements for the ifSdh MIB. (R24.0)
1.3.6.1.4.1.8708.2.52.2NodelumIfSdhMIBObjects
1.3.6.1.4.1.8708.2.52.2.1NodeifSdhGeneral
1.3.6.1.4.1.8708.2.52.2.1.1ScalarifSdhGeneralConfigLastChangeTimeread-onlycurrentThe time when the configuration of the MIB was last changed.
1.3.6.1.4.1.8708.2.52.2.1.2ScalarifSdhGeneralStateLastChangeTimeread-onlycurrentThe time when the state and/or configuration of the MIB was last changed.
1.3.6.1.4.1.8708.2.52.2.1.3ScalarifSdhGeneralIfSdhRsTableSizeread-onlycurrentSize of rs table.
1.3.6.1.4.1.8708.2.52.2.1.4ScalarifSdhGeneralIfSdhRsConfigLastChangeTimeread-onlycurrentThe time when the configuration of the table was last changed.
1.3.6.1.4.1.8708.2.52.2.1.5ScalarifSdhGeneralIfSdhRsStateLastChangeTimeread-onlycurrentThe time when the state of the table was last changed.
1.3.6.1.4.1.8708.2.52.2.1.6ScalarifSdhGeneralIfSdhMsTableSizeread-onlycurrentSize of ms table
1.3.6.1.4.1.8708.2.52.2.1.7ScalarifSdhGeneralIfSdhMsConfigLastChangeTimeread-onlycurrentThe time when the configuration of the table was last changed.
1.3.6.1.4.1.8708.2.52.2.1.8ScalarifSdhGeneralIfSdhMsStateLastChangeTimeread-onlycurrentThe time when the state and/or configuration of the table was last changed.
1.3.6.1.4.1.8708.2.52.2.2NodeifSdhRsList
1.3.6.1.4.1.8708.2.52.2.2.1TableifSdhRsTablenot-accessiblecurrentThe regenerator (rs) group contains information and configuration for the regenerator section (rs).
1.3.6.1.4.1.8708.2.52.2.2.1.1RowifSdhRsEntrynot-accessiblecurrentAn entry in the ifSdh rs list.
1.3.6.1.4.1.8708.2.52.2.2.1.1.1ColumnifSdhRsIndexread-onlycurrentAn index assigned to each entry.
1.3.6.1.4.1.8708.2.52.2.2.1.1.2ColumnifSdhRsNameread-onlycurrentThe management name of the optical transmission section, for example 'rs:1:2:1-2', where the first number indicates subrack, the second slot number and the thi…
1.3.6.1.4.1.8708.2.52.2.2.1.1.3ColumnifSdhRsConnIfBasicIfIndexread-onlycurrentAn index that describes to which index in ifBasicIf table this object is related.
1.3.6.1.4.1.8708.2.52.2.2.1.1.4ColumnifSdhRsOhTransparencyBitmaskread-onlycurrentThe OH transparency bitmask. Bits: B1 = 0x01 E1 = 0x02 F1 = 0x04 D1-D3 = 0x08 J0 = 0x10
1.3.6.1.4.1.8708.2.52.2.2.1.1.5ColumnifSdhRsTraceTransmittedread-onlycurrentThe trace to be transmitted from this interface. Default value: <IP address>:<subrack>:<slot>:<port> Note that only the last part of the address is used. The t…
1.3.6.1.4.1.8708.2.52.2.2.1.1.6ColumnifSdhRsTraceReceivedread-onlycurrentThe received trace for this interface. The trace _notApplicable_ is used to tell SNMP clients that attribute is not used in current configuration. The trace _n…
1.3.6.1.4.1.8708.2.52.2.2.1.1.7ColumnifSdhRsTraceExpectedread-onlycurrentTrace used for matching against the received trace. The trace _notApplicable_ is used to tell SNMP clients that attribute is not used in current configuration.
1.3.6.1.4.1.8708.2.52.2.2.1.1.8ColumnifSdhRsTraceAlarmModeread-onlycurrentControls if the trace identifier mismatch alarm should be raised if received trace and expected trace differs. disabled - The alarm is disabled. enabled - The …
1.3.6.1.4.1.8708.2.52.2.2.1.1.9ColumnifSdhRsTxSignalStatusread-onlycurrentThe state for outgoing (TX) signal of the interface. down - A major fault has occurred. degraded - The signal quality is impaired. up - The signal is OK.
1.3.6.1.4.1.8708.2.52.2.2.1.1.10ColumnifSdhRsRxSignalStatusread-onlycurrentThe state for incoming (RX) signal of the interface. down - A major fault has occurred. degraded - The signal quality is impaired. up - The signal is OK.
1.3.6.1.4.1.8708.2.52.2.2.1.1.11ColumnifSdhRsTraceMismatchread-onlycurrentTrace identifier mismatch (TIM). Indicates if the expected trace identifier differs from the received trace identifier. Reference: J0: G.707/9.2.2.2, TIM: G.80…
1.3.6.1.4.1.8708.2.52.2.2.1.1.12ColumnifSdhRsLossOfFrameread-onlycurrentRx RS-Loss of frame (LOF). Reference: G.707/9.2.2.1, G.783/2.5.1, G.783/9.3.1.2 alarm: An RSOH frame cannot be located. ok: An RSOH frame can be located.
1.3.6.1.4.1.8708.2.52.2.2.1.1.13ColumnifSdhRsTxLossOfFrameread-onlycurrentTx RS-Loss of frame (LOF). Reference: G.707/9.2.2.1, G.783/2.5.1, G.783/9.3.1.2 alarm: An RSOH frame cannot be located. ok: An RSOH frame can be located.
1.3.6.1.4.1.8708.2.52.2.3NodeifSdhMsList
1.3.6.1.4.1.8708.2.52.2.3.1TableifSdhMsTablenot-accessiblecurrentThe multiplexing (ms) group contains information and configuration for the multiplexing section (ms).
1.3.6.1.4.1.8708.2.52.2.3.1.1RowifSdhMsEntrynot-accessiblecurrentAn entry in the ifSdh ms list.
1.3.6.1.4.1.8708.2.52.2.3.1.1.1ColumnifSdhMsIndexread-onlycurrentAn index assigned to each entry.
1.3.6.1.4.1.8708.2.52.2.3.1.1.2ColumnifSdhMsNameread-onlycurrentThe management name of the optical transmission section, for example 'ms:1:2:1-2', where the first number indicates subrack, the second slot number and the thi…
1.3.6.1.4.1.8708.2.52.2.3.1.1.3ColumnifSdhMsConnIfBasicIfIndexread-onlycurrentAn index that describes to which index in ifBasicIf table this object is related.
1.3.6.1.4.1.8708.2.52.2.3.1.1.4ColumnifSdhMsOhTransparencyBitmaskread-onlycurrentThe OH transparency bitmask. Bits: B2 = 0x01 E2 = 0x02 D4-D12 = 0x04 K1-K2 = 0x08
1.3.6.1.4.1.8708.2.52.2.3.1.1.5ColumnifSdhMsTxSignalStatusread-onlycurrentThe state for outgoing (TX) signal of the interface. down - A major fault has occurred. degraded - The signal quality is impaired. up - The signal is OK.
1.3.6.1.4.1.8708.2.52.2.3.1.1.6ColumnifSdhMsRxSignalStatusread-onlycurrentThe state for incoming (RX) signal of the interface. down - A major fault has occurred. degraded - The signal quality is impaired. up - The signal is OK.
1.3.6.1.4.1.8708.2.52.2.3.1.1.7ColumnifSdhMsRxAlarmIndicationSignalread-onlycurrentRx MS-Alarm indication signal (AIS). Reference: G.806/6.2.6.2, G.806/6.3.1, G.806/Appendix III alarm: An MS AIS signal is detected. ok: The MS AIS is cleared.
1.3.6.1.4.1.8708.2.52.2.3.1.1.8ColumnifSdhMsRemoteDefectIndicationread-onlycurrentRx MS-Remote defect indication (RDI). Reference: G1: G.707/9.3.1.4, G.806/6.2.6.3, G.806/6.3.2 alarm: RDI indication (in frame) active. ok: RDI indication inac…
1.3.6.1.4.1.8708.2.52.2.3.1.1.9ColumnifSdhMsTxAlarmIndicationSignalread-onlycurrentTx MS-Alarm indication signal (AIS). Reference: G.806/6.2.6.2, G.806/6.3.1, G.806/Appendix III alarm: An MS AIS signal is detected. ok: The MS AIS is cleared.
1.3.6.1.4.1.8708.2.52.2.4NodeifSdhAuList
1.3.6.1.4.1.8708.2.52.2.5NodeifSdhVcList