RAD-HDLC-MIB
170 objects
No module-level DESCRIPTION found.
Imported Objects
| IF-MIB | InterfaceIndex |
| RAD-MIB | diverseIfWanGen fileName |
| SNMPv2-SMI | Gauge32 Integer32 IpAddress NOTIFICATION-TYPE OBJECT-TYPE |
| SNMPv2-TC | DisplayString RowStatus |
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.164.3.1.6.5 | NodehdlcMibObjects | |||
| 1.3.6.1.4.1.164.3.1.6.5.1 | TablehdlcTable | not-accessible | current | The HDLC configuration table. |
| 1.3.6.1.4.1.164.3.1.6.5.1.1 | RowhdlcEntry | not-accessible | current | Defines the contents of each line in the RAD HDLC Table. |
| 1.3.6.1.4.1.164.3.1.6.5.1.1.1 | ColumnhdlcProtocol | read-write | current | The HDLC protocol type V35 - HDLC encapsulated over V35 X21 - HDLC encapsulated over X21 RS530 - HDLC encapsulated over RS530 |
| 1.3.6.1.4.1.164.3.1.6.5.1.1.2 | ColumnhdlcRateResolution | read-write | current | The baud rate of the internal clock. |
| 1.3.6.1.4.1.164.3.1.6.5.1.1.3 | ColumnhdlcTxClockSource | read-write | current | The baud rate of the internal clock. |
| 1.3.6.1.4.1.164.3.1.6.5.1.1.4 | ColumnhdlcTerminalMode | read-write | current | . |
| 1.3.6.1.4.1.164.3.1.6.5.1.1.5 | ColumnhdlcLoopbackState | read-write | current | internal - All data coming from the network port is looped back external - All data comming from the line is looped back. |
| 1.3.6.1.4.1.164.3.1.6.5.1.1.6 | ColumnhdlcTxClockPolarity | read-write | current | normal - The transmitted data is sampled at the middle of bit time inverse - The transmitted data is sampled at the end of the bit time (high data rate/long ca… |
| 1.3.6.1.4.1.164.3.1.6.5.1.1.7 | ColumnhdlcFlowControl | read-write | current | Enable/Disable the CTS/RTS flow control signals. |
| 1.3.6.1.4.1.164.3.1.6.5.1.1.8 | ColumnhdlcLineRate | read-write | current | The rate values for HDLC are n*56/64Kbps, where 1<=n<=32, 64, 128 and the following values: 1544, 3088, 6176. The rate values for HSSI is nMbps, where 1<=n<=52. |
| 1.3.6.1.4.1.164.3.1.6.5.1.1.9 | ColumnhdlcRxClockMode | read-write | current | . |
| 1.3.6.1.4.1.164.3.1.6.5.1.1.10 | ColumnhdlcLOF | read-only | current | Total number of seconds the port is in Loss Of Frame state. |
| 1.3.6.1.4.1.164.3.1.6.5.1.1.11 | ColumnhdlcRxClockPolarity | read-write | current | normal - The received data is sampled at the middle of bit time inverse - The received data is sampled at the end of the bit time (high data rate/long cable). |
| 1.3.6.1.4.1.164.3.1.6.5.2 | NodehdlcPerformance | |||
| 1.3.6.1.4.1.164.3.1.6.5.2.1 | TablehdlcCurrentTable | not-accessible | current | The HDLC Current table. |
| 1.3.6.1.4.1.164.3.1.6.5.2.1.1 | RowhdlcCurrentEntry | not-accessible | current | An entry in the HDLC Current table. |
| 1.3.6.1.4.1.164.3.1.6.5.2.1.1.1 | ColumnhdlcCurrentIfIndex | read-only | current | The index of the HDLC interface. It may be ifIndex. |
| 1.3.6.1.4.1.164.3.1.6.5.2.1.1.2 | ColumnhdlcCurrentStatus | read-only | current | The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was… |
| 1.3.6.1.4.1.164.3.1.6.5.2.1.1.3 | ColumnhdlcCurrentLOF | read-only | current | The counter associated with the number of seconds the port is in Loss Of Frame state, encountered by the HDLC interface in the current 15 minute interval. |
| 1.3.6.1.4.1.164.3.1.6.5.2.1.1.4 | ColumnhdlcCurrentInFrames | read-only | current | The counter associated with the number of received frames, encountered by the HDLC interface in the current 15 minute interval. |
| 1.3.6.1.4.1.164.3.1.6.5.2.1.1.5 | ColumnhdlcCurrentInErrors | read-only | current | The counter associated with the number of Errored received frames, encountered by the HDLC interface in the current 15 minute interval. |
| 1.3.6.1.4.1.164.3.1.6.5.2.1.1.6 | ColumnhdlcCurrentOutFrames | read-only | current | The counter associated with the number of transmitted frames, encountered by the HDLC interface in the current 15 minute interval. |
| 1.3.6.1.4.1.164.3.1.6.5.2.1.1.7 | ColumnhdlcCurrentAbortedFrames | read-only | current | The counter associated with the number of frames, in which at least seven consecutive '1'-s (Abort sequence) were encountered by the HDLC interface in the curr… |
| 1.3.6.1.4.1.164.3.1.6.5.2.1.1.8 | ColumnhdlcCurrentLengthError | read-only | current | The counter associated with the number of received frames with length error, encountered by the HDLC interface in the current 15 minute interval. |
| 1.3.6.1.4.1.164.3.1.6.5.2.2 | TablehdlcIntervalTable | not-accessible | current | The HDLC Interval table. |
| 1.3.6.1.4.1.164.3.1.6.5.2.2.1 | RowhdlcIntervalEntry | not-accessible | current | An entry in the HDLC Interval table. |
| 1.3.6.1.4.1.164.3.1.6.5.2.2.1.1 | ColumnhdlcIntervalIfIndex | read-only | current | The index of the HDLC interface. It may be ifIndex. |
| 1.3.6.1.4.1.164.3.1.6.5.2.2.1.2 | ColumnhdlcIntervalNumber | read-only | current | A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that … |
| 1.3.6.1.4.1.164.3.1.6.5.2.2.1.3 | ColumnhdlcIntervalStatus | read-only | current | The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was… |
| 1.3.6.1.4.1.164.3.1.6.5.2.2.1.4 | ColumnhdlcIntervalLOF | read-only | current | The counter associated with the number of seconds the port is in Loss Of Frame state, encountered by an HDLC interface in one of the previous 96, individual 15… |
| 1.3.6.1.4.1.164.3.1.6.5.2.2.1.5 | ColumnhdlcIntervalInFrames | read-only | current | The counter associated with the number of received frames, encountered by the HDLC interface in one of the previous 96, individual 15 minute, intervals. |
| 1.3.6.1.4.1.164.3.1.6.5.2.2.1.6 | ColumnhdlcIntervalInErrors | read-only | current | The counter associated with the number of Errored received frames, encountered by the HDLC interface in one of the previous 96, individual 15 minute, intervals. |
| 1.3.6.1.4.1.164.3.1.6.5.2.2.1.7 | ColumnhdlcIntervalOutFrames | read-only | current | The counter associated with the number of transmitted frames, encountered by the HDLC interface in one of the previous 96, individual 15 minute, intervals. |
| 1.3.6.1.4.1.164.3.1.6.5.2.2.1.8 | ColumnhdlcIntervalAbortedFrames | read-only | current | The counter associated with the number of frames, in which at least seven consecutive '1'-s (Abort sequence) were encountered by the HDLC interface in one of t… |
| 1.3.6.1.4.1.164.3.1.6.5.2.2.1.9 | ColumnhdlcIntervalLengthError | read-only | current | The counter associated with the number of received frames with length error, encountered by the HDLC interface in one of the previous 96, individual 15 minute,… |
| 1.3.6.1.4.1.164.6.1.11.0.1 | NotificationrtrFACSViolation | current | The trap is sent for every violation of a FACS filter. | |
| 1.3.6.1.4.1.164.6.1.11.0.2 | NotificationrtrSwDwnLoadTrap | current | The trap is sent after the tftp download of the software and before the decompression and reset operations. | |
| 1.3.6.1.4.1.164.11.1 | NodertrInterfaces | |||
| 1.3.6.1.4.1.164.11.1.1 | TablertrConfigIfTable | not-accessible | current | Table of configured interfaces. |
| 1.3.6.1.4.1.164.11.1.1.1 | RowrtrConfigIfEntry | not-accessible | current | Each entry defines a configured interface. |
| 1.3.6.1.4.1.164.11.1.1.1.1 | ColumnrtrConfigIfIndex | read-only | current | This variable uniquely identifies the interface. It is used as a cross reference in other system tables |
| 1.3.6.1.4.1.164.11.1.1.1.2 | ColumnrtrConfigIfType | read-create | current | This variable identifies the type of the specific entry in the rtrDynamicIfConfigTable. This field is writable only at creation time (i.e., when value of statu… |
| 1.3.6.1.4.1.164.11.1.1.1.3 | ColumnrtrConfigIfName | read-create | current | This variable provides a logical name to a specific entry in rtrConfigIfTable. It is also used in identifying the Driver interfaces. |
| 1.3.6.1.4.1.164.11.1.1.1.4 | ColumnrtrConfigIfStatus | read-create | current | The status of the ConfigEntry. The choices are those defined in SNMPv2-TC. Only: active, createAndWait, and destroy will be used. active - The conceptual row i… |
| 1.3.6.1.4.1.164.11.1.2 | TablertrIfCfgTable | not-accessible | current | Router Interface Configuration Table. |
| 1.3.6.1.4.1.164.11.1.2.1 | RowrtrIfCfgEntry | not-accessible | current | An entry in the Router Interface Configuration Table. |
| 1.3.6.1.4.1.164.11.1.2.1.1 | ColumnrtrIfCfgIndex | read-create | current | This object indicates the Router Interface Index. (In some cases it will be equal to the Router Interface ifIndex). |
| 1.3.6.1.4.1.164.11.1.2.1.2 | ColumnrtrIfCfgIpAddress | read-create | current | IP Address of the Router Interface. |
| 1.3.6.1.4.1.164.11.1.2.1.3 | ColumnrtrIfCfgRowStatus | read-create | current | This object enables the user to create/delete entries of this table. |
| 1.3.6.1.4.1.164.11.1.2.1.4 | ColumnrtrIfCfgIpMask | read-create | current | IP Mask Address Router Interface. |
| 1.3.6.1.4.1.164.11.1.2.1.5 | ColumnrtrIfCfgIfIndex | read-create | current | ifIndex of the device interface connected to this Router Interface. |
| 1.3.6.1.4.1.164.11.1.2.1.6 | ColumnrtrIfCfgType | read-create | current | The Router Interface Type. atm - ATM router interface lis - Logical IP Subnet router interface. ethernet - Ethernet router interface. |
| 1.3.6.1.4.1.164.11.1.2.1.7 | ColumnrtrIfCfgVlanId | read-create | current | The VLAN ID assigned to Tagged frames transmitted from this Router Interface. The value inserted should be a defined VLAN. |
| 1.3.6.1.4.1.164.11.1.2.1.8 | ColumnrtrIfCfgMtu | read-create | current | The size of the largest packet which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagram… |
| 1.3.6.1.4.1.164.11.2 | NodeipSpec | |||
| 1.3.6.1.4.1.164.11.2.1 | TablertrIpAddrTable | not-accessible | current | This table is parralel to MIB II IpAddrTable, and is used to add/delete entries to/from that table. In addition it contains private objects. |
| 1.3.6.1.4.1.164.11.2.1.1 | RowrtrIpAddrEntry | not-accessible | current | The addressing information for one of this entity's IP addresses. |
| 1.3.6.1.4.1.164.11.2.1.1.1 | ColumnrtrIpAdEntAddr | read-only | current | The IP address to which this entry's addressing information pertains. |
| 1.3.6.1.4.1.164.11.2.1.1.2 | ColumnrtrIpAdEntIfIndex | read-create | current | The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the … |
| 1.3.6.1.4.1.164.11.2.1.1.3 | ColumnrtrIpAdEntNetMask | read-create | current | The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits … |
| 1.3.6.1.4.1.164.11.2.1.1.4 | ColumnrtrIpAdEntForwardIpBroadcast | read-create | current | This variable controls forwarding of IP (sub)net-directed broadcasts destined for an attached sub(net). |
| 1.3.6.1.4.1.164.11.2.1.1.5 | ColumnrtrIpAdEntBackupAddr | read-create | current | |
| 1.3.6.1.4.1.164.11.2.1.1.6 | ColumnrtrIpAdEntStatus | read-create | current | The Status variable is used to create and destroy a Ip Addresses. |
| 1.3.6.1.4.1.164.11.2.2 | NodeicmpSpec | |||
| 1.3.6.1.4.1.164.11.2.2.1 | ScalarrtrIcmpGenErrMsgEnable | read-write | current | This variable controlls the ability to generate ICMP error messages |
| 1.3.6.1.4.1.164.11.2.2.2 | TablertrIcmpRdTable | not-accessible | current | This table contains ICMP Router Discovery parameters configurated per IP interface. |
| 1.3.6.1.4.1.164.11.2.2.2.1 | RowrtrIcmpRdEntry | not-accessible | current | The ICMP parameters configurated for IP interface. |
| 1.3.6.1.4.1.164.11.2.2.2.1.1 | ColumnrtrIcmpRdIpAddr | read-only | current | The IP address to which this entry's information pertains. |
| 1.3.6.1.4.1.164.11.2.2.2.1.2 | ColumnrtrIcmpRdIpAdvertAddr | read-write | current | The IP destination address to be used for multicast Router Advertisements sent from the interface. The only permissible values are the all-systems multicast ad… |
| 1.3.6.1.4.1.164.11.2.2.2.1.3 | ColumnrtrIcmpRdMaxAdvertInterval | read-write | current | The maximum time allowed between sending multicast Router Advertisements from the interface, in seconds. Must be no less than 4 seconds and no greater than 180… |
| 1.3.6.1.4.1.164.11.2.2.2.1.4 | ColumnrtrIcmpRdMinAdvertInterval | read-write | current | The minimum time allowed between sending unsolicited multicast Router Advertisements from the interface, in seconds. Must be no less than 3 seconds and no grea… |
| 1.3.6.1.4.1.164.11.2.2.2.1.5 | ColumnrtrIcmpRdAdvertLifetime | read-write | current | The maximum length of time that the advertised addresses are to be considered as valid. Must be no less than rtrIcmpRdMaxAdvertInterval and no greater than 900… |
| 1.3.6.1.4.1.164.11.2.2.2.1.6 | ColumnrtrIcmpRdAdvertise | read-write | current | A flag indicating whether or not the address is to be advertised. |
| 1.3.6.1.4.1.164.11.2.2.2.1.7 | ColumnrtrIcmpRdPreferenceLevel | read-write | current | The preferability of the address as a default router address, relative to other router addresses on the same subnet. |
| 1.3.6.1.4.1.164.11.2.2.2.1.8 | ColumnrtrIcmpRdEntStatus | read-write | current | Setting of any value to this object set values of all fields to the default values. |
| 1.3.6.1.4.1.164.11.2.3 | Noderip2Spec | |||
| 1.3.6.1.4.1.164.11.2.3.1 | TablertrRip2IfConfTable | not-accessible | current | This table is an extension of rip2IfConfTable (RFC 1724 ,RIP 2). It means that every time somebody creates/destroys a row in the rip2IfConfTable, the same row … |
| 1.3.6.1.4.1.164.11.2.3.1.1 | RowrtrRip2IfConfEntry | not-accessible | current | An entry in table rtrRip2IfConfTable. |
| 1.3.6.1.4.1.164.11.2.3.1.1.1 | ColumnrtrRip2IfConfAddress | read-only | current | The IP Address of this system on the indicated subnet. For unnumbered interfaces, the value 0.0.0.N, where the least significant 24 bits (N) is the ifIndex for… |
| 1.3.6.1.4.1.164.11.2.3.1.1.2 | ColumnrtrRip2IfConfVirtualDis | read-write | deprecated | This variable defines the virtual number of hops assigned to the interface specified by rtrIfIpAddrIndex. This enables fine-tuning of the RIP routing algorithm. |
| 1.3.6.1.4.1.164.11.2.3.1.1.3 | ColumnrtrRip2IfConfAutoSend | read-write | deprecated | When set to enable only the default route is sent through the interface. When set to disable, regular RIPs are sent. |
| 1.3.6.1.4.1.164.11.2.3.1.1.4 | ColumnrtrRip2IfConfRipEnable | read-write | current | This object shows whether RIP Protocol is enabled on the current interface. |
| 1.3.6.1.4.1.164.11.2.4 | NodearpSpec | |||
| 1.3.6.1.4.1.164.11.2.4.1 | ScalarrtrArpDeleteTable | read-write | current | Setting this object to any not-null value has the effect of deleting all entries of the ARP table. |
| 1.3.6.1.4.1.164.11.2.4.2 | ScalarrtrArpInactiveTimeOut | read-write | current | This variable defines the maximum time period (in second) that can pass between ARP requests concerning an entry in the ARP table. After this time period, the … |
| 1.3.6.1.4.1.164.11.2.4.3 | ScalarrtrArpProxy | read-write | current | When ARP Proxy is enabled, the router can respond to ARP requests for nodes located on a different sub-net, provided they are it its network table. The router … |
| 1.3.6.1.4.1.164.11.2.5 | NodertrNat | |||
| 1.3.6.1.4.1.164.11.2.5.1 | TablertrNatIfConfTable | not-accessible | current | A list of interfaces which require separate NAT configuration. |
| 1.3.6.1.4.1.164.11.2.5.1.1 | RowrtrNatIfConfEntry | not-accessible | current | A single routing domain in a single subnet. |
| 1.3.6.1.4.1.164.11.2.5.1.1.1 | ColumnrtrNatIfVirtualAddress | read-only | current | The IP Address of the virtual subnet to be translated by the 'NAT box' attached to this interface. |
| 1.3.6.1.4.1.164.11.2.5.1.1.2 | ColumnrtrNatIfVirtualMask | read-only | current | The subnet Mask of the virtual subnet. |
| 1.3.6.1.4.1.164.11.2.5.1.1.3 | ColumnrtrNatIfConfStatus | read-create | current | Writing 'destroy' has the effect of deleting this interface. |
| 1.3.6.1.4.1.164.11.2.5.1.1.4 | ColumnrtrNatIfRealAddress | read-create | current | The IP Address of the real subnet which is used by 'NAT box' for translation. |
| 1.3.6.1.4.1.164.11.2.5.1.1.5 | ColumnrtrNatIfRealMask | read-create | current | The subnet Mask of the real subnet. |
| 1.3.6.1.4.1.164.11.2.5.1.1.6 | ColumnrtrNatIfType | read-create | current | NAT type. static - Translate a specific virtual IP network to a specific real IP network. TCP, UDP and ICMP sessions originated both in real and virtual networ… |
| 1.3.6.1.4.1.164.11.2.5.2 | TablertrPatTable | not-accessible | current | Port Address Translation (PAT - single IP NAT) configuration Table. |
| 1.3.6.1.4.1.164.11.2.5.2.1 | RowrtrPatEntry | not-accessible | current | Each entry describe unique mapping between real IP address, range of ports and protocol, to local (virtual) IP address. Ports are used in the TCP (rfc793) to n… |
| 1.3.6.1.4.1.164.11.2.5.2.1.1 | ColumnrtrPatIdx | read-only | current | Running index for PAT table. |
| 1.3.6.1.4.1.164.11.2.5.2.1.2 | ColumnrtrPatRealAddress | read-create | current | The real IP Address used for translation |
| 1.3.6.1.4.1.164.11.2.5.2.1.3 | ColumnrtrPatVirtualAddress | read-create | current | The virtual IP Address used for translation |
| 1.3.6.1.4.1.164.11.2.5.2.1.4 | ColumnrtrPatLowestPort | read-create | current | Lowest Port number for this PAT entry |
| 1.3.6.1.4.1.164.11.2.5.2.1.5 | ColumnrtrPatHighestPort | read-create | current | Highest Port number for this PAT entry |
| 1.3.6.1.4.1.164.11.2.5.2.1.6 | ColumnrtrPatProtocol | read-create | current | Protocol selected. This Protocol and port range (lowest port - highest port) define the application (FTP, Telnet, SMTP etc.). Protocol enumaration numbers corr… |
| 1.3.6.1.4.1.164.11.2.5.2.1.7 | ColumnrtrPatStatus | read-create | current | This object enables creating and deleting entries of the table. |
| 1.3.6.1.4.1.164.11.5 | NodertrFACS | |||
| 1.3.6.1.4.1.164.11.5.1 | ScalarrtrFACSDefaultAction | read-write | current | Used to define the default action for the device, when no FACS statements applicable to a given frame are defined. |
| 1.3.6.1.4.1.164.11.5.2 | TablertrFACSActTable | not-accessible | current | The table of FACS action. |
| 1.3.6.1.4.1.164.11.5.2.1 | RowrtrFACSActEntry | not-accessible | current | Each rtrFACSActEntry consist of the following parameters |
| 1.3.6.1.4.1.164.11.5.2.1.1 | ColumnrtrFACSActType | read-only | current | This parameter indicates on which FACS Table the FACS action will preform. |
| 1.3.6.1.4.1.164.11.5.2.1.2 | ColumnrtrFACSActIfIndex | read-only | current | The interface to which this FACS entry is applicable. |
| 1.3.6.1.4.1.164.11.5.2.1.3 | ColumnrtrFACSAction | read-write | current | The management station that sends a SET request for one of these actions with indexes rtrFACSType and rtrFACSIfIndex defines the type and the interface Id for … |
| 1.3.6.1.4.1.164.11.5.2.1.4 | ColumnrtrFACSActiveDB | read-write | current | This parameter will point on which Facs DataBase the SNMP agent read. The Active dataBase is Read Only. The user may change FACS statements in the temporary Da… |
| 1.3.6.1.4.1.164.11.5.3 | TablertrFACSTable | not-accessible | current | The table of FACS statment. |
| 1.3.6.1.4.1.164.11.5.3.1 | RowrtrFACSEntry | not-accessible | current | Each FACS statment consists of the following parameters |
| 1.3.6.1.4.1.164.11.5.3.1.1 | ColumnrtrFACSIfIndex | read-only | current | The interface to which this FACS entry is applicable. For applications this variables is always 0. |
| 1.3.6.1.4.1.164.11.5.3.1.2 | ColumnrtrFACSProtocolType | read-only | current | This parameter define the protocol the Security Access Control is applicable. |
| 1.3.6.1.4.1.164.11.5.3.1.3 | ColumnrtrFACSType | read-only | current | The Mode of in which this FACS statement operates. For applications this variable is always rx(2). |
| 1.3.6.1.4.1.164.11.5.3.1.4 | ColumnrtrFACSIndex | read-only | current | Index to the FACS Table. |
| 1.3.6.1.4.1.164.11.5.3.1.5 | ColumnrtrFACSSrcAdd | read-write | current | The size of the octet string will be according to the protocol type defined in rtrFACSProtocolType. |
| 1.3.6.1.4.1.164.11.5.3.1.6 | ColumnrtrFACSSrcAddMask | read-write | current | Source-address mask . |
| 1.3.6.1.4.1.164.11.5.3.1.7 | ColumnrtrFACSDesAdd | read-write | current | Destination-address The size of the octet string will be according to the protocol type define in rtrFACSProtocolType . |
| 1.3.6.1.4.1.164.11.5.3.1.8 | ColumnrtrFACSDesAddMask | read-write | current | Destination-address mask . |
| 1.3.6.1.4.1.164.11.5.3.1.9 | ColumnrtrFACSOperation | read-write | current | ... . |
| 1.3.6.1.4.1.164.11.5.3.1.10 | ColumnrtrFACSNetFiltering | read-write | current | ... . |
| 1.3.6.1.4.1.164.11.5.3.1.11 | ColumnrtrFACSSocketNum | read-write | current | Port/socket number for different applications 0 is default meaning not applicable. none(1), ftp(21), telnet(23), smtp(25), tftp(69), snmp(161), snmpTrap(162), … |
| 1.3.6.1.4.1.164.11.5.3.1.12 | ColumnrtrFACSMask1Id | read-write | current | Index into RND mask table FACS/COD Type) . |
| 1.3.6.1.4.1.164.11.5.3.1.13 | ColumnrtrFACSMask2Id | read-write | current | Index into RND mask table FACS/COD according to the value of rtrFACSType . |
| 1.3.6.1.4.1.164.11.5.3.1.14 | ColumnrtrFACSStatus | read-write | current | The status of a table entry. |
| 1.3.6.1.4.1.164.11.5.4 | ScalarrtrFACSFrameData | read-only | current | Data from the frame that violated a FACS Filter. |
| 1.3.6.1.4.1.164.11.7.1 | TablertrBridgePortConfigTable | not-accessible | current | Table of the bridge ports |
| 1.3.6.1.4.1.164.11.7.1.1 | RowrtrBridgePortConfigEntry | not-accessible | current | Each entry defines a bridge port |
| 1.3.6.1.4.1.164.11.7.1.1.1 | ColumnrtrBridgePortCIndex | read-only | current | This is the index of the bridge port. It is the same as 'dot1dBasePort' of the Bridge MIB. |
| 1.3.6.1.4.1.164.11.7.1.1.2 | ColumnrtrBridgePortCIf | read-create | current | The config ifIndex the bridge port is sitting on. |
| 1.3.6.1.4.1.164.11.7.1.1.3 | ColumnrtrBridgePortCStatus | read-create | current | The status of the RtrBridgePortConfigEntry. Creating and destroying the bridge port is done by this variable. |
| 1.3.6.1.4.1.164.11.9 | NoderadRouterConfig | |||
| 1.3.6.1.4.1.164.11.9.1 | TablertrConfigTable | not-accessible | current | The Router's Configuration table. |
| 1.3.6.1.4.1.164.11.9.1.1 | RowrtrConfigEntry | not-accessible | current | An entry in the Router's Configuration table. |
| 1.3.6.1.4.1.164.11.9.1.1.1 | ColumnrtrConfigIndex | read-only | current | This object indicates the Router's Index. |
| 1.3.6.1.4.1.164.11.9.1.1.2 | ColumnrtrConfigDefaultGateway | read-write | current | Router Default Gateway. |
| 1.3.6.1.4.1.164.11.9.1.1.3 | ColumnrtrConfigArpAgingTime | read-write | current | ARP Aging Time. |
| 1.3.6.1.4.1.164.11.9.1.1.5 | ColumnrtrConfigClassifierTosMask | read-write | current | This object indicates the Classifier's TOS Mask, as follows: 0x1C for DTR 0x1E for Cisco 0xE0 for Precedence 0xFC for Diffserv Else for Manual . |
| 1.3.6.1.4.1.164.11.9.1.1.6 | ColumnrtrConfigRIPMode | read-write | current | This object determines the Router Information Protocol to measure the shortest path between 2 positions on the network. |
| 1.3.6.1.4.1.164.11.9.3 | TablertrFwdTable | not-accessible | current | The Router's Forwarding Table. |
| 1.3.6.1.4.1.164.11.9.3.1 | RowrtrFwdEntry | not-accessible | current | An entry in the Router's Forwarding table. |
| 1.3.6.1.4.1.164.11.9.3.1.1 | ColumnrtrFwdIdx | read-only | current | This object indicates the Router Index. |
| 1.3.6.1.4.1.164.11.9.3.1.2 | ColumnrtrFwdIpAddress | read-only | current | This object indicates the Destination IP Address. |
| 1.3.6.1.4.1.164.11.9.3.1.3 | ColumnrtrFwdIpMask | read-only | current | This object indicates the Mask IP address. |
| 1.3.6.1.4.1.164.11.9.3.1.4 | ColumnrtrFwdRuleIdx | read-only | current | This object indicates the Rule's Number. |
| 1.3.6.1.4.1.164.11.9.3.1.5 | ColumnrtrFwdRowStatus | read-create | current | This object enables the user to create/delete entries in this table. Entry of Type rtrFwdType = staticRouting(3) are created by the user. Only this type of ent… |
| 1.3.6.1.4.1.164.11.9.3.1.6 | ColumnrtrFwdNextHop | read-create | current | This object indicates the IP Address of the Next Hop. |
| 1.3.6.1.4.1.164.11.9.3.1.7 | ColumnrtrFwdIfIndex | read-only | current | This object indicates the Interface Index. |
| 1.3.6.1.4.1.164.11.9.3.1.8 | ColumnrtrFwdType | read-create | current | The type of route. Note that local(3) refers to a route for which the next hop is the final destination; remote(4) refers to a route for which the next hop is … |
| 1.3.6.1.4.1.164.11.9.3.1.9 | ColumnrtrFwdProto | read-only | current | The routing mechanism via which this route was learned. Inclusion of values for gateway routing protocols is not intended to imply that hosts should support th… |
| 1.3.6.1.4.1.164.11.9.3.1.10 | ColumnrtrFwdEthQueue | read-create | current | This object indicates the ETH Queue number. |
| 1.3.6.1.4.1.164.11.9.3.1.11 | ColumnrtrFwdMetric1 | read-create | current | The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's rtrFwdProto value. If t… |
| 1.3.6.1.4.1.164.12.6 | NoderadAtmSignalingMonitor | |||
| 1.3.6.1.4.1.164.12.6.1 | ScalarsmSVCOperState | read-only | current | The SVC monitoring operational state. |
| 1.3.6.1.4.1.164.12.6.2 | ScalarsmSVCAdminStatus | read-write | current | The SVC monitoring status. |
| 1.3.6.1.4.1.164.12.6.3 | ScalarsmILMIMode | read-write | current | The ILMI operational Mode. |
| 1.3.6.1.4.1.164.12.6.4 | ScalarsmILMIStatus | read-only | current | ILMI protocol status (VCC 0,16). |
| 1.3.6.1.4.1.164.12.6.5 | ScalarsmUNIVersion | read-write | current | The UNI version that is used by both sides. |
| 1.3.6.1.4.1.164.12.6.6 | ScalarsmPolicing | read-write | current | The type of the police action performed on the cells transmitted from the user side to the network side. |
| 1.3.6.1.4.1.164.12.6.7 | ScalarsmSAALStatus | read-only | current | Signaling data link (VCC 0,5) status. |
| 1.3.6.1.4.1.164.12.6.8 | ScalarsmOpenedSesssions | read-only | current | The number of SVC sessions currently opened. |
| 1.3.6.1.4.1.164.12.6.9 | ScalarsmUserRejectedSessions | read-only | current | The number of sessions that the user side rejected to open. |
| 1.3.6.1.4.1.164.12.6.10 | ScalarsmNetworkRejectedSessions | read-only | current | The number of sessions that the Network side rejected. |
| 1.3.6.1.4.1.164.12.6.11 | ScalarsmHostRejectedSessions | read-only | current | The number of sessions that the device rejected to open. |
| 1.3.6.1.4.1.164.12.6.12 | ScalarsmVclILMISessionVpi | read-write | current | ILMI Keep alive session VPI channel. Default: 0. (VCI=16, fixed). |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| RtrIfConfigTYPE | INTEGER |