RC-IPV6-MIB
373 objects
Enterprise MIB for the Accelar product family.
Imported Objects
| OID | Name | Access | Status | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2272.1.8.26 | NodercIpRsmlt | |||
| 1.3.6.1.4.1.2272.1.8.26.5 | TablercIpv6RsmltOperTable | not-accessible | current | Route Smlt Table |
| 1.3.6.1.4.1.2272.1.8.26.5.1 | RowrcIpv6RsmltOperEntry | not-accessible | current | A local IPv6 RSMLT entry |
| 1.3.6.1.4.1.2272.1.8.26.5.1.1 | ColumnrcIpv6RsmltOperIfIndex | not-accessible | current | Route Smlt Oper IfIndex. |
| 1.3.6.1.4.1.2272.1.8.26.5.1.2 | ColumnrcIpv6RsmltOperIpv6Addr | not-accessible | current | IPv6 Interface with RSMLT on. |
| 1.3.6.1.4.1.2272.1.8.26.5.1.3 | ColumnrcIpv6RsmltOperIpv6PrefixLength | not-accessible | current | IPv6 Prefix Length. |
| 1.3.6.1.4.1.2272.1.8.26.5.1.4 | ColumnrcIpv6RsmltOperAdminStatus | read-write | current | is a enable/disable flag. |
| 1.3.6.1.4.1.2272.1.8.26.5.1.5 | ColumnrcIpv6RsmltOperHoldDownTimer | read-write | current | Timer value, the range of value is from 0 to 3600. |
| 1.3.6.1.4.1.2272.1.8.26.5.1.6 | ColumnrcIpv6RsmltOperHoldDownTimeRemaining | read-only | current | The time value that indicate how much time remaining of HoldDownTimer. |
| 1.3.6.1.4.1.2272.1.8.26.5.1.7 | ColumnrcIpv6RsmltOperHoldUpTimer | read-write | current | The range of value 0 to 3600 or 9999. 9999 means infinity. |
| 1.3.6.1.4.1.2272.1.8.26.5.1.8 | ColumnrcIpv6RsmltOperHoldUpTimeRemaining | read-only | current | The time value that indicate how much time remaining of HoldUpTimer. |
| 1.3.6.1.4.1.2272.1.8.26.5.1.9 | ColumnrcIpv6RsmltOperOperStatus | read-only | current | The operation status of Rsmlt, up or down. |
| 1.3.6.1.4.1.2272.1.8.26.5.1.10 | ColumnrcIpv6RsmltOperSmltId | read-only | current | The id range for SMLT is 1-32. |
| 1.3.6.1.4.1.2272.1.8.26.5.1.11 | ColumnrcIpv6RsmltOperSltId | read-only | current | The id range for SLT is 1-512. |
| 1.3.6.1.4.1.2272.1.8.26.5.1.12 | ColumnrcIpv6RsmltOperVlanId | read-only | current | Vlan id. |
| 1.3.6.1.4.1.2272.1.8.26.5.1.13 | ColumnrcIpv6RsmltOperMacAddr | read-only | current | Mac Address. |
| 1.3.6.1.4.1.2272.1.8.26.5.1.14 | ColumnrcIpv6RsmltOperVrfId | read-only | current | Indicates the Virtual Router to which the RSMLT Oper instance belongs. |
| 1.3.6.1.4.1.2272.1.8.26.5.1.15 | ColumnrcIpv6RsmltOperVrfName | read-only | current | Name of the Virtual Router to which the RSMLT Oper instance belongs. |
| 1.3.6.1.4.1.2272.1.8.26.6 | TablercIpv6RsmltPeerTable | not-accessible | current | Route Smlt Peer Table |
| 1.3.6.1.4.1.2272.1.8.26.6.1 | RowrcIpv6RsmltPeerEntry | not-accessible | current | An entry of Ip As Path Access List Table. |
| 1.3.6.1.4.1.2272.1.8.26.6.1.1 | ColumnrcIpv6RsmltPeerIfIndex | not-accessible | current | Route Smlt Oper IfIndex. |
| 1.3.6.1.4.1.2272.1.8.26.6.1.2 | ColumnrcIpv6RsmltPeerIpv6Addr | not-accessible | current | IP Interface with RSMLT on. |
| 1.3.6.1.4.1.2272.1.8.26.6.1.3 | ColumnrcIpv6RsmltPeerIpv6PrefixLength | not-accessible | current | IPv6 Prefix Length |
| 1.3.6.1.4.1.2272.1.8.26.6.1.4 | ColumnrcIpv6RsmltPeerAdminStatus | read-only | current | is a enable/disable flag. |
| 1.3.6.1.4.1.2272.1.8.26.6.1.5 | ColumnrcIpv6RsmltPeerHoldDownTimer | read-only | current | Timer value, the range of value is from 0 to 3600. |
| 1.3.6.1.4.1.2272.1.8.26.6.1.6 | ColumnrcIpv6RsmltPeerHoldDownTimeRemaining | read-only | current | The time value that indicate how much time remaining of HoldDownTimer. |
| 1.3.6.1.4.1.2272.1.8.26.6.1.7 | ColumnrcIpv6RsmltPeerHoldUpTimer | read-only | current | The range of value 0 to 3600 or 9999. 9999 means infinity. |
| 1.3.6.1.4.1.2272.1.8.26.6.1.8 | ColumnrcIpv6RsmltPeerHoldUpTimeRemaining | read-only | current | The time value that indicate how much time remaining of HoldUpTimer. |
| 1.3.6.1.4.1.2272.1.8.26.6.1.9 | ColumnrcIpv6RsmltPeerOperStatus | read-only | current | The operation status of Rsmlt, up or down. |
| 1.3.6.1.4.1.2272.1.8.26.6.1.10 | ColumnrcIpv6RsmltPeerSmltId | read-only | current | The id range for SMLT is 1-32. |
| 1.3.6.1.4.1.2272.1.8.26.6.1.11 | ColumnrcIpv6RsmltPeerSltId | read-only | current | The id range for SLT is 1-512. |
| 1.3.6.1.4.1.2272.1.8.26.6.1.12 | ColumnrcIpv6RsmltPeerVlanId | read-only | current | Vlan id. |
| 1.3.6.1.4.1.2272.1.8.26.6.1.13 | ColumnrcIpv6RsmltPeerMacAddr | read-only | current | Mac Address. |
| 1.3.6.1.4.1.2272.1.8.26.6.1.14 | ColumnrcIpv6RsmltPeerVrfId | read-only | current | Indicates the Virtual Router to which the RSMLT Peer instance belongs. |
| 1.3.6.1.4.1.2272.1.8.26.6.1.15 | ColumnrcIpv6RsmltPeerVrfName | read-only | current | Name of the Virtual Router to which the RSMLT Peer instance belongs. |
| 1.3.6.1.4.1.2272.1.8.26.7 | TablercIpv6RsmltEdgePeerTable | not-accessible | current | RSMLT Edge Support Peer Info table. This table consists of the RSMLT Peers for which the switch will act as a PeerForwarder. |
| 1.3.6.1.4.1.2272.1.8.26.7.1 | RowrcIpv6RsmltEdgePeerEntry | not-accessible | current | RSMLT Edge Support Peer Info Entry |
| 1.3.6.1.4.1.2272.1.8.26.7.1.1 | ColumnrcIpv6RsmltEdgePeerVlanId | not-accessible | current | A value that uniquely identifies the Virtual LAN associated with this entry. |
| 1.3.6.1.4.1.2272.1.8.26.7.1.2 | ColumnrcIpv6RsmltEdgePeerIpv6Address | not-accessible | current | IP address of the Peer RSMLT Interface. |
| 1.3.6.1.4.1.2272.1.8.26.7.1.3 | ColumnrcIpv6RsmltEdgePeerIpv6PrefixLength | not-accessible | current | If set then this prefix can be used for address autoconfig, passed opaquely to Infinity |
| 1.3.6.1.4.1.2272.1.8.26.7.1.4 | ColumnrcIpv6RsmltEdgePeerMacAddress | read-only | current | The MAC address of the Peer RSMLT interface. |
| 1.3.6.1.4.1.2272.1.8.26.7.1.5 | ColumnrcIpv6RsmltEdgePeerVrfId | read-only | current | Indicates the Virtual Router to which the RSMLT Edge Peer instance belongs. |
| 1.3.6.1.4.1.2272.1.8.26.7.1.6 | ColumnrcIpv6RsmltEdgePeerVrfName | read-only | current | Name of the Virtual Router to which the RSMLT Edge Peer instance belongs. |
| 1.3.6.1.4.1.2272.1.8.26.7.1.7 | ColumnrcIpv6RsmltEdgePeerIsRaPrefix | read-only | current | True if this is a Router Advertisement prefix, False if this is a global address. |
| 1.3.6.1.4.1.2272.1.8.26.7.1.8 | ColumnrcIpv6RsmltEdgePeerConfType | read-only | current | Type of configured address, passed opaquely to Infinity |
| 1.3.6.1.4.1.2272.1.8.26.7.1.9 | ColumnrcIpv6RsmltEdgePeerNoAdvertise | read-only | current | True if advertisement of this prefix is disabled, passed opaquely to Infinity |
| 1.3.6.1.4.1.2272.1.8.26.7.1.10 | ColumnrcIpv6RsmltEdgePeerOspf6Advertise | read-only | current | True if OSPFv3 advertisement of this prefix is enabled, passed opaquely to Infinity |
| 1.3.6.1.4.1.2272.1.8.26.7.1.11 | ColumnrcIpv6RsmltEdgePeerPrefCandidate | read-only | current | True if address is considered for preferred selection, passed opaquely to Infinity |
| 1.3.6.1.4.1.2272.1.8.26.7.1.12 | ColumnrcIpv6RsmltEdgePeerPfxValidLife | read-only | current | Valid lifetime in seconds, passed opaquely to Infinity |
| 1.3.6.1.4.1.2272.1.8.26.7.1.13 | ColumnrcIpv6RsmltEdgePeerPfxPrefLife | read-only | current | Preferred lifetime in seconds, passed opaquely to Infinity |
| 1.3.6.1.4.1.2272.1.8.26.7.1.14 | ColumnrcIpv6RsmltEdgePeerPfxOnLinkFlag | read-only | current | If set then this prefix can be used for onlink determination, passed opaquely to Infinity |
| 1.3.6.1.4.1.2272.1.8.26.7.1.15 | ColumnrcIpv6RsmltEdgePeerPfxAutoFlag | read-only | current | If set then this prefix can be used for address autoconfig, passed opaquely to Infinity |
| 1.3.6.1.4.1.2272.1.62.1 | IdentityrcIpv6Mib | of | Enterprise MIB for the Accelar product family. | |
| 1.3.6.1.4.1.2272.1.62.1.0 | NodercIpv6Notifications | |||
| 1.3.6.1.4.1.2272.1.62.1.1 | NodercIpv6Objects | |||
| 1.3.6.1.4.1.2272.1.62.1.1.1 | NodercIpv6Scalars | |||
| 1.3.6.1.4.1.2272.1.62.1.1.1.1 | ScalarrcIpv6IcmpErrorInterval | read-write | current | The rate limit interval (in milliseconds) at which ICMP error messages can be sent out. A value of zero means no rate limit. |
| 1.3.6.1.4.1.2272.1.62.1.1.1.2 | ScalarrcIpv6MulticastAdminStatus | read-write | current | This indicates the global admin status for multicast. |
| 1.3.6.1.4.1.2272.1.62.1.1.1.3 | ScalarrcIpv6IcmpNetUnreach | read-write | current | Used to set the icmp net unreach feature enable/disable. |
| 1.3.6.1.4.1.2272.1.62.1.1.1.4 | ScalarrcIpv6IcmpRedirectMsg | read-write | current | used to set the icmp redirect feature enable/disable. |
| 1.3.6.1.4.1.2272.1.62.1.1.1.5 | ScalarrcIpv6IcmpErrorQuota | read-write | current | The number of ICMP error messages that can be sent out during ICMP error interval. A value of zero means not be send any. |
| 1.3.6.1.4.1.2272.1.62.1.1.1.6 | ScalarrcIpv6GlobalAdminEnabled | read-write | current | Indicates whether IPv6 has been administratively enabled. |
| 1.3.6.1.4.1.2272.1.62.1.1.1.7 | ScalarrcIpv6GlobalOperEnabled | read-write | current | Indicates whether IPv6 is currently enabled. |
| 1.3.6.1.4.1.2272.1.62.1.1.1.8 | ScalarrcIpv6PrefixListTableSize | read-only | current | Size of Ipv6 Prefix List Table |
| 1.3.6.1.4.1.2272.1.62.1.1.1.9 | ScalarrcIpv6ClearDhcpCounters | read-write | current | Setting this object will clear IPv6 DHCP counters. |
| 1.3.6.1.4.1.2272.1.62.1.1.1.10 | ScalarrcIpv6RouteStaticClear | read-write | current | Clear all IPv6 static routes. |
| 1.3.6.1.4.1.2272.1.62.1.1.1.11 | ScalarrcIpv6RouteStaticGlobalAdminEnabled | read-write | current | Used to globally enable/disable all IPv6 static routes. |
| 1.3.6.1.4.1.2272.1.62.1.1.1.12 | ScalarrcIpv6IcmpAnycastEchoReply | read-write | current | Used to enable/disable icmp echo reply msg for anycast addresses. |
| 1.3.6.1.4.1.2272.1.62.1.1.1.13 | ScalarrcIpv6IcmpMulticastEchoReply | read-write | current | Used to enable/disable icmp echo reply msg for multicast addresses. |
| 1.3.6.1.4.1.2272.1.62.1.1.1.14 | ScalarrcIpv6Autoconfig | read-write | current | Used to enable / disable IPv6 autoconfiguration from router advertisements |
| 1.3.6.1.4.1.2272.1.62.1.1.1.15 | ScalarrcIpv6IcmpAddrUnreach | read-write | current | Used to enable / disable address unreachable message |
| 1.3.6.1.4.1.2272.1.62.1.1.1.16 | ScalarrcIpv6IcmpPortUnreach | read-write | current | Used to enable / disable port unreachable message |
| 1.3.6.1.4.1.2272.1.62.1.1.1.17 | ScalarrcIpv6SlowPathToCpu | read-write | current | Used to enable / disable slow-path-to-cpu |
| 1.3.6.1.4.1.2272.1.62.1.1.1.18 | ScalarrcIpv6ClearGlobalIcmpStats | read-write | current | Setting this object will clear global IPv6 ICMP statistics |
| 1.3.6.1.4.1.2272.1.62.1.1.1.19 | ScalarrcIpv6EcmpEnable | read-write | current | Used to globally enable/disable equal-cost multi-path feature. |
| 1.3.6.1.4.1.2272.1.62.1.1.1.20 | ScalarrcIpv6EcmpMaxPath | read-write | current | Used to globally set the maximum number of paths that can be equal cost. |
| 1.3.6.1.4.1.2272.1.62.1.1.1.21 | ScalarrcIpv6RoutePrefTableSize | read-only | current | table size of the rcIpv6RoutePrefTable |
| 1.3.6.1.4.1.2272.1.62.1.1.1.22 | ScalarrcIpv6AlternativeRouteEnable | read-write | current | Used to globally enable/disable alterative-route |
| 1.3.6.1.4.1.2272.1.62.1.1.1.23 | ScalarrcIpv6SourceRouteEnable | read-write | current | Used to globally enable/disable ipv6 source routing feature. |
| 1.3.6.1.4.1.2272.1.62.1.1.1.24 | ScalarrcIpv6IcmpMulticastRequestEnable | read-write | current | Used to globally enable/disable ipv6 icmp echo multicast request feature. |
| 1.3.6.1.4.1.2272.1.62.1.1.1.25 | NodercIpv6IsisGenInFilter | |||
| 1.3.6.1.4.1.2272.1.62.1.1.1.25.1 | ScalarrcIpv6IsisInFilterNickNameTableSize | read-only | current | Ipv6 Isis In Filter Nick Name table size |
| 1.3.6.1.4.1.2272.1.62.1.1.1.25.2 | ScalarrcIpv6IsisInFilterIsidTableSize | read-only | current | Ipv6 Isis In Filter Isid table size |
| 1.3.6.1.4.1.2272.1.62.1.1.1.25.3 | ScalarrcIpv6IsisInFilterNickNameIsidTableSize | read-only | current | Ipv6 Isis In Filter Nick Name Isid table size |
| 1.3.6.1.4.1.2272.1.62.1.1.1.25.4 | ScalarrcIpv6IsisInFilterIsidListTableSize | read-only | current | Ipv6 Isis In Filter Isid List table size |
| 1.3.6.1.4.1.2272.1.62.1.1.1.25.5 | ScalarrcIpv6IsisInFilterNickNameIsidListTableSize | read-only | current | Ipv6 Isis In Filter Nick Name Isid List table size |
| 1.3.6.1.4.1.2272.1.62.1.1.1.25.6 | ScalarrcIpv6IsisInFilterApply | read-write | current | Used to Apply the Ipv6 Isis Accept filters. When the value is set to apply, all the elements in the in the various Ipv6 Isis In Filter Tables will be applied a… |
| 1.3.6.1.4.1.2272.1.62.1.1.1.26 | NodercIpv6IsisInFilterDefault | |||
| 1.3.6.1.4.1.2272.1.62.1.1.1.26.1 | ScalarrcIpv6IsisInFilterPolicyName | read-write | current | Route Map name |
| 1.3.6.1.4.1.2272.1.62.1.1.2 | TablercIpv6InterfaceTable | not-accessible | current | This table contains list of IPv6 interfaces and per-interface IPv6-specific information. |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1 | RowrcIpv6InterfaceEntry | not-accessible | current | An entry of ipv6 interface In Table containing per-interface information. |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.1 | ColumnrcIpv6InterfaceIfIndex | not-accessible | current | An unique value to identify a physical interface or a logical interface (VLAN). For the brouter port it is the ifindex of the port and in the case of the vlan … |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.2 | ColumnrcIpv6InterfaceIdentifier | read-create | current | IPv6 address interface identifiers. This is a binary string of up to 8 octets in network byte-order. |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.3 | ColumnrcIpv6InterfaceIdentifierLength | read-create | current | The length of the Interface Identifier in bits. |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.4 | ColumnrcIpv6InterfaceDescr | read-create | current | A textual string containing information about the interface. This string may be set by network management system. |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.5 | ColumnrcIpv6InterfaceVlanId | read-create | current | A value that uniquely identifies the Virtual LAN associated with this entry. This value corresponds to the lower 12 bits in the IEEE 802.1Q VLAN Tag. |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.6 | ColumnrcIpv6InterfaceType | read-create | current | The interface type. Only ethernet and loopback values are configurable. |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.7 | ColumnrcIpv6InterfaceReasmMaxSize | read-create | current | MTU for this IPv6 interface, this value should be same for all the ip addresses defined on this interface. |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.8 | ColumnrcIpv6InterfacePhysAddress | read-only | current | The media-dependent `physical' address, for the ethernet media it is the MAC address |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.9 | ColumnrcIpv6InterfaceAdminStatus | read-create | current | The indication of whether IPv6 is enabled (up) or disabled (down) on this interface. This object does not affect the state of the interface itself, only its co… |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.10 | ColumnrcIpv6InterfaceOperStatus | read-only | current | Operating status of the interface. |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.11 | ColumnrcIpv6InterfaceReachableTime | read-create | current | The time (in milliseconds) a neighbor is considered reachable after receiving a reachability confirmation. REFERENCE RFC2461, Section 6.3.2 |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.12 | ColumnrcIpv6InterfaceRetransmitTime | read-create | deprecated | The time (in milliseconds) between retransmissions of Neighbor Solicitation messages to a neighbor when resolving the address or when probing the reachability … |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.13 | ColumnrcIpv6InterfaceMulticastAdminStatus | read-create | current | This indicates the admin status for multicast for this interface. |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.14 | ColumnrcIpv6InterfaceRowStatus | read-create | current | Row status for create/delete. |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.15 | ColumnrcIpv6InterfaceDhcpEnabled | read-create | current | Enable or disable DHCP on the specified interface. |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.16 | ColumnrcIpv6InterfaceMacOffset | read-create | current | Used to request a particular MAC for an IPv6 VLAN. Analogous to rcIpAdEntMacOffset in rcIpAddrTable. The system has 512 mac addresses of which 0-507 are reserv… |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.17 | ColumnrcIpv6InterfaceRetransmitTimer | read-create | current | The time (in milliseconds) between retransmissions of Neighbor Solicitation messages to a neighbor when resolving the address or when probing the reachability … |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.18 | ColumnrcIpv6InterfaceCurHopLimit | read-create | current | The default value to be placed in the current hop limit field in router advertisements sent from this interface. The value should be set to the current diamete… |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.20 | ColumnrcIpv6InterfaceClearIcmpStats | read-create | current | Clear ICMP statistics for an interface |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.21 | ColumnrcIpv6InterfaceClearGeneralStats | read-create | current | Clear general statistics for an interface |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.22 | ColumnrcIpv6InterfaceClearNeighborCache | read-create | current | Clear Neighbor Cache for an interface |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.23 | ColumnrcIpv6InterfaceClearDestinationCache | read-create | current | Clear Destination Cache for an interface |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.24 | ColumnrcIpv6InterfaceReversePathCheckEnable | read-create | current | Used to indicate whether this interface should perform Reverse Path Check |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.25 | ColumnrcIpv6InterfaceReversePathCheckMode | read-create | current | Reverse Path Checking mode. |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.26 | ColumnrcIpv6InterfaceForwardingEnabled | read-create | current | Used to indicate whether this interface should perform forwarding |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.27 | ColumnrcIpv6InterfaceRsmltEnable | read-create | current | Used to indicate whether this interface has rsmlt enabled or not |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.28 | ColumnrcIpv6InterfaceBfdEnable | read-create | current | Used to indicate whether this interface has BFD enabled or not |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.29 | ColumnrcIpv6InterfaceProcessRedirect | read-create | current | Used to indicate whether this interface has ProcessRedirect enabled or not |
| 1.3.6.1.4.1.2272.1.62.1.1.2.1.30 | ColumnrcIpv6InterfaceIpsecEnable | read-create | current | Used to indicate whether this interface has IPSec enabled or disabled |
| 1.3.6.1.4.1.2272.1.62.1.1.3 | TablercIpv6AddressTable | not-accessible | current | This table contains addressing information relevant to the entity's interfaces. This table does not contain multicast address information. Tables for such info… |
| 1.3.6.1.4.1.2272.1.62.1.1.3.1 | RowrcIpv6AddressEntry | not-accessible | current | An address mapping for a particular interface. Note that when an address is added to an interface the resulted prefix is added to that interface. |
| 1.3.6.1.4.1.2272.1.62.1.1.3.1.1 | ColumnrcIpv6AddressIfIndex | not-accessible | current | The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the … |
| 1.3.6.1.4.1.2272.1.62.1.1.3.1.2 | ColumnrcIpv6AddressAddr | not-accessible | current | The IPv6 address to which this entry's addressing information pertains. This is one of the ipv6 addresses that this interface(identified by the rcIpv6AddressIf… |
| 1.3.6.1.4.1.2272.1.62.1.1.3.1.3 | ColumnrcIpv6AddressType | read-create | current | The type of address. It is either unicast or anycast IPv6 addresses (RFC3513). |
| 1.3.6.1.4.1.2272.1.62.1.1.3.1.4 | ColumnrcIpv6AddressPrefixLength | read-create | current | Prefix Length value for this address. Cannot be changed after the creation. This field MUST be provided in order to create an entry in this table. |
| 1.3.6.1.4.1.2272.1.62.1.1.3.1.5 | ColumnrcIpv6AddressPrefix | read-only | current | A pointer to the row in the prefix table to which this address belongs. May be { 0 0 } if there is no such row. |
| 1.3.6.1.4.1.2272.1.62.1.1.3.1.6 | ColumnrcIpv6AddressOrigin | read-only | current | The origin of the address. The origin of the address, one of: other(1),manual(2), dhcp(4),linklayer(5), random(6) |
| 1.3.6.1.4.1.2272.1.62.1.1.3.1.7 | ColumnrcIpv6AddressStatus | read-only | current | The status of the address, describing if the address can be used for communication. It will One of: preferred(1), deprecated(2),invalid(3),inaccessible(4),unkn… |
| 1.3.6.1.4.1.2272.1.62.1.1.3.1.8 | ColumnrcIpv6AddressCreated | read-only | current | The value of sysUpTime at the time this entry was created. If this entry was created prior to the last re- initialization of the local network management subsy… |
| 1.3.6.1.4.1.2272.1.62.1.1.3.1.9 | ColumnrcIpv6AddressLastChanged | read-only | current | The value of sysUpTime at the time this entry was last updated. If this entry was updated prior to the last re- initialization of the local network management … |
| 1.3.6.1.4.1.2272.1.62.1.1.3.1.10 | ColumnrcIpv6AddressRowStatus | read-create | current | The status of this conceptual row. The RowStatus TC requires that this DESCRIPTION clause states under which circumstances other objects in this row can be mod… |
| 1.3.6.1.4.1.2272.1.62.1.1.3.1.11 | ColumnrcIpv6AddressValidLifetime | read-only | current | Valid lifetime in seconds, indicates how long this address is valid. A result of 4294967295 means infinite |
| 1.3.6.1.4.1.2272.1.62.1.1.3.1.12 | ColumnrcIpv6AddressPrefLifetime | read-only | current | Preferred lifetime in seconds, indicates how long this address is in use and not deprecated. A result of 4294967295 means infinite |
| 1.3.6.1.4.1.2272.1.62.1.1.3.1.13 | ColumnrcIpv6AddressIfType | read-only | current | The address entry IfType indicates the type of the interface. In the case of circuit-less-IP there is no association with any ports. In other words, it can be … |
| 1.3.6.1.4.1.2272.1.62.1.1.3.1.14 | ColumnrcIpv6AddressName | read-create | current | The administratively assignmed name for this address. |
| 1.3.6.1.4.1.2272.1.62.1.1.4 | TablercIpv6PrefixTable | not-accessible | current | This table allows the user to determine the source of an IP address or set of IP addresses and allows other tables to share the information via pointer rather … |
| 1.3.6.1.4.1.2272.1.62.1.1.4.1 | RowrcIpv6PrefixEntry | not-accessible | current | An entry of ipv6 prefix In the Table. |
| 1.3.6.1.4.1.2272.1.62.1.1.4.1.1 | ColumnrcIpv6PrefixIfIndex | not-accessible | current | An unique value to identify an ipv6 interface. For the brouter port it is the ifindex of the port and in the case of the vlan it is the ifindex of the vlan. |
| 1.3.6.1.4.1.2272.1.62.1.1.4.1.2 | ColumnrcIpv6PrefixAddr | not-accessible | current | Prefix to create an ipv6 address in ipv6 interface table. |
| 1.3.6.1.4.1.2272.1.62.1.1.4.1.3 | ColumnrcIpv6PrefixLength | not-accessible | current | Mask to create an ipv6 prefix entry either will be advertised or suppressed |
| 1.3.6.1.4.1.2272.1.62.1.1.4.1.4 | ColumnrcIpv6PrefixVlanId | read-only | current | A value that uniquely identifies the Virtual LAN associated with this entry. This value corresponds to the lower 12 bits in the IEEE 802.1Q VLAN Tag. |
| 1.3.6.1.4.1.2272.1.62.1.1.4.1.5 | ColumnrcIpv6PrefixUseDefaultVal | read-create | current | Select one of the value to set/use it's value to default value. This is a bitmask field, setting all the bits means that all the options will be reverted to de… |
| 1.3.6.1.4.1.2272.1.62.1.1.4.1.6 | ColumnrcIpv6PrefixValidLife | read-create | current | Valid lifetime in seconds, indicates how long this prefix advertised in the nbr advertisement is valid. |
| 1.3.6.1.4.1.2272.1.62.1.1.4.1.7 | ColumnrcIpv6PrefixPreferredLife | read-create | current | Preferred lifetime in seconds, indicates how long this prefix advertised in advertisemt for this prefix. |
| 1.3.6.1.4.1.2272.1.62.1.1.4.1.8 | ColumnrcIpv6PrefixAtValidLife | read-create | current | Is the date and time, upon reaching this value the prefix will be expired, if configured this option will be included in the neighbor advertisement for this pr… |
| 1.3.6.1.4.1.2272.1.62.1.1.4.1.9 | ColumnrcIpv6PrefixAtPreferredLife | read-create | current | Is the date and time, upon reaching this value the prefix will be expired, if configured this option will be included in the neighbor advertisement for this pr… |
| 1.3.6.1.4.1.2272.1.62.1.1.4.1.10 | ColumnrcIpv6PrefixInfinite | read-create | current | if set the prefix's valid lifetime will not exprie. |
| 1.3.6.1.4.1.2272.1.62.1.1.4.1.11 | ColumnrcIpv6PrefixOnLinkFlag | read-create | current | if set then this prefix can be used for onlink determination. This value be placed in the L-bit field in the prefix information option. It is a 1 bit flag. |
| 1.3.6.1.4.1.2272.1.62.1.1.4.1.12 | ColumnrcIpv6PrefixAutoFlag | read-create | current | if set then this prefix can be used for autonomous address config. This value be placed in the auto-flag field in the prefix information option. It is a 1 bit … |
| 1.3.6.1.4.1.2272.1.62.1.1.4.1.13 | ColumnrcIpv6PrefixAddressEui | read-create | current | Use an EUI-64 interface ID in the low-order 64bits of the address when not specified in the address field. If enabled use EUI, otherwise use EUI-64 and complem… |
| 1.3.6.1.4.1.2272.1.62.1.1.4.1.14 | ColumnrcIpv6PrefixNoAdvertise | read-create | current | if set then this prefix can not be included in the neighbor advertisement. |
| 1.3.6.1.4.1.2272.1.62.1.1.4.1.15 | ColumnrcIpv6PrefixRowStatus | read-create | current | Row status for create/delete. |
| 1.3.6.1.4.1.2272.1.62.1.1.4.1.16 | ColumnrcIpv6PrefixValidLifetime | read-create | current | Valid lifetime in seconds, indicates how long this prefix advertised in the nbr advertisement is valid. Value of 4294967295 represents infinity. |
| 1.3.6.1.4.1.2272.1.62.1.1.4.1.17 | ColumnrcIpv6PrefixPreferredLifetime | read-create | current | Preferred lifetime in seconds, indicates how long this prefix advertised in advertisemt for this prefix. Value of 4294967295 represents infinity. |
| 1.3.6.1.4.1.2272.1.62.1.1.5 | TablercIpv6RouterAdvertTable | not-accessible | current | The table containing information used to construct router advertisements. |
| 1.3.6.1.4.1.2272.1.62.1.1.5.1 | RowrcIpv6RouterAdvertEntry | not-accessible | current | An entry containing information used to construct router advertisements. |
| 1.3.6.1.4.1.2272.1.62.1.1.5.1.1 | ColumnrcIpv6RouterAdvertIfIndex | not-accessible | current | An unique value to identify an ipv6 interface. For the brouter port it is the ifindex of the port and in the case of the vlan it is the ifindex of the vlan. |
| 1.3.6.1.4.1.2272.1.62.1.1.5.1.2 | ColumnrcIpv6RouterAdvertSendAdverts | read-write | current | A flag indicating whether or not the router sends periodic router advertisements and responds to router solicitations on this interface. REFERENCE RFC2461 Sect… |
| 1.3.6.1.4.1.2272.1.62.1.1.5.1.3 | ColumnrcIpv6RouterAdvertUseDefaultVal | read-write | current | Select one of the value to set/use it's value to default value, or set all the bits to indicate all the options will be set to their default value. |
| 1.3.6.1.4.1.2272.1.62.1.1.5.1.4 | ColumnrcIpv6RouterAdvertMaxInterval | read-write | current | Configure the max interval (in seconds) at which the transmission of route advertisments can occur on this interface. This must be no less than 4 seconds and n… |
| 1.3.6.1.4.1.2272.1.62.1.1.5.1.5 | ColumnrcIpv6RouterAdvertMinInterval | read-write | current | Configure the min interval (in seconds) at which the transmission of route advertisments can occur on this interface. This must be no less than 3 seconds and n… |
| 1.3.6.1.4.1.2272.1.62.1.1.5.1.6 | ColumnrcIpv6RouterAdvertReachableTime | read-write | current | The value (in milliseconds) to be placed in the router advertisement message sent by the router. The value zero means unspecified (by this router). Used to con… |
| 1.3.6.1.4.1.2272.1.62.1.1.5.1.7 | ColumnrcIpv6RouterAdvertRetransmitTimer | read-only | deprecated | The value (in milliseconds) to be placed in the retransmit timer field in router advertisement message sent from this interface. The value zero means unspecifi… |
| 1.3.6.1.4.1.2272.1.62.1.1.5.1.8 | ColumnrcIpv6RouterAdvertDefaultLifeTime | read-write | current | The value to be placed in the router lifetime field of router advertisements sent from this interface. This value MUST be either 0 or between rcIpv6RouterAdver… |
| 1.3.6.1.4.1.2272.1.62.1.1.5.1.9 | ColumnrcIpv6RouterAdvertCurHopLimit | read-write | current | The default value to be placed in the current hop limit field in router advertisements sent from this interface. The value should be set to the current diamete… |
| 1.3.6.1.4.1.2272.1.62.1.1.5.1.10 | ColumnrcIpv6RouterAdvertManagedFlag | read-write | current | if true then the M-bit(Managed address configureation) in the router adverisement will be set. REFERENCE RFC2461 Section 6.2.1 |
| 1.3.6.1.4.1.2272.1.62.1.1.5.1.11 | ColumnrcIpv6RouterAdvertOtherConfigFlag | read-write | current | if true then the O-bit (Other stateful Configuration) in the router adverisement will be set. REFERENCE RFC2461 Section 6.2.1 |
| 1.3.6.1.4.1.2272.1.62.1.1.5.1.12 | ColumnrcIpv6RouterAdvertDadNsNum | read-write | current | The number of neighbor solicitation messages for DAD (Duplicate address detection). A value 0 is used to disable DAD process on this interface. A value 1 is us… |
| 1.3.6.1.4.1.2272.1.62.1.1.5.1.13 | ColumnrcIpv6RouterAdvertLinkMTU | read-only | current | The value to be placed in MTU options sent by the router on this interface. A value of zero indicates that no MTU options are sent. REFERENCE RFC2461 Section 6… |
| 1.3.6.1.4.1.2272.1.62.1.1.5.1.14 | ColumnrcIpv6RouterAdvertRetransmitTime | read-write | current | The value (in milliseconds) to be placed in the retransmit timer field in router advertisement message sent from this interface. The value zero means unspecifi… |
| 1.3.6.1.4.1.2272.1.62.1.1.6 | TablercIpv6StaticRouteTable | not-accessible | current | This table contains list of routes that are created by the user to destination networks. |
| 1.3.6.1.4.1.2272.1.62.1.1.6.1 | RowrcIpv6StaticRouteEntry | not-accessible | current | An entry in the static route table for IPv6 can be created for a destination with a specific prefix length; multiple entries to the same destination are create… |
| 1.3.6.1.4.1.2272.1.62.1.1.6.1.1 | ColumnrcIpv6StaticRouteDest | not-accessible | current | The destination IPv6 address of this route. The values for the index objects rcIpv6StaticRouteDest and rcIpv6StaticRoutePrefixLength must be consistent. When t… |
| 1.3.6.1.4.1.2272.1.62.1.1.6.1.2 | ColumnrcIpv6StaticRoutePrefixLength | not-accessible | current | Indicates the number of leading one bits which form the mask to be logical-ANDed with the destination address before being compared to the value in the rcIpv6S… |
| 1.3.6.1.4.1.2272.1.62.1.1.6.1.3 | ColumnrcIpv6StaticRouteNextHop | not-accessible | current | Next hop IPv6 address for this destination. On remote routes, the address of the next system en route. For non-remote routes, a zero length string. |
| 1.3.6.1.4.1.2272.1.62.1.1.6.1.4 | ColumnrcIpv6StaticRouteIfIndex | not-accessible | current | The ifIndex value which identifies the local interface through which the next hop of this route should be reached. A value of 0 is valid and represents the sce… |
| 1.3.6.1.4.1.2272.1.62.1.1.6.1.5 | ColumnrcIpv6StaticRouteDistance | read-create | current | cost/distance to reach the destination for this node. |
| 1.3.6.1.4.1.2272.1.62.1.1.6.1.6 | ColumnrcIpv6StaticRouteStatus | read-only | current | Used to indicate the current status of entry in routing table. 1. notReachable means the route is unreachable via the specified next hop. 2. tryToResolve means… |
| 1.3.6.1.4.1.2272.1.62.1.1.6.1.7 | ColumnrcIpv6StaticRoutePreference | read-create | current | Used to indicate the route preference of this entry. If there are more than one route that can be used to forward IP traffic, the route that has a highest pref… |
| 1.3.6.1.4.1.2272.1.62.1.1.6.1.8 | ColumnrcIpv6StaticRouteEnable | read-create | current | Used to enable/disable this entry. |
| 1.3.6.1.4.1.2272.1.62.1.1.6.1.9 | ColumnrcIpv6StaticRouteRowStatus | read-create | current | Row status for create/delete. |
| 1.3.6.1.4.1.2272.1.62.1.1.6.1.10 | ColumnrcIpv6StaticRouteName | read-create | current | An administratively-assigned name for this static route |
| 1.3.6.1.4.1.2272.1.62.1.1.7 | TablercIpv6NetToPhysicalTable | not-accessible | current | The IP Address Translation table used for mapping from IP addresses to physical addresses. The Address Translation tables contain the IP address to 'physical' … |
| 1.3.6.1.4.1.2272.1.62.1.1.7.1 | RowrcIpv6NetToPhysicalEntry | not-accessible | current | Each entry contains one IP address to `physical' address equivalence. |
| 1.3.6.1.4.1.2272.1.62.1.1.7.1.1 | ColumnrcIpv6NetToPhysicalIfIndex | not-accessible | current | The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the … |
| 1.3.6.1.4.1.2272.1.62.1.1.7.1.2 | ColumnrcIpv6NetToPhysicalNetAddress | not-accessible | current | The IP Address corresponding to the media-dependent `physical' address. The address type of this object is specified in rcIpv6NetToPhysicalAddressType. Impleme… |
| 1.3.6.1.4.1.2272.1.62.1.1.7.1.3 | ColumnrcIpv6NetToPhysicalPhysAddress | read-create | current | The media-dependent `physical' address. As the entries in this table are typically not persistent when this object is written the entity SHOULD NOT save the ch… |
| 1.3.6.1.4.1.2272.1.62.1.1.7.1.4 | ColumnrcIpv6NetToPhysicalInterface | read-create | current | The field represents either a physical port id or the MLT port id. This entry is associated either with a port or with a MLT in a VLAN/Brouter port. If the val… |
| 1.3.6.1.4.1.2272.1.62.1.1.7.1.5 | ColumnrcIpv6NetToPhysicalLastUpdated | read-only | current | The value of sysUpTime at the time this entry was last updated. If this entry was updated prior to the last re- initialization of the local network management … |
| 1.3.6.1.4.1.2272.1.62.1.1.7.1.6 | ColumnrcIpv6NetToPhysicalType | read-create | current | The type of mapping. The 'dynamic(2)' type indicates that the IP address to physical addresses mapping has been dynamically resolved using e.g. IPv4 ARP or the… |
| 1.3.6.1.4.1.2272.1.62.1.1.7.1.8 | ColumnrcIpv6NetToPhysicalState | read-only | current | The Neighbor Unreachability Detection [4] state for the interface when the address mapping in this entry is used. If Neighbor Unreachability Detection is not i… |
| 1.3.6.1.4.1.2272.1.62.1.1.7.1.9 | ColumnrcIpv6NetToPhysicalRowStatus | read-create | current | The status of this conceptual row. The RowStatus TC requires that this DESCRIPTION clause states under which circumstances other objects in this row can be mod… |
| 1.3.6.1.4.1.2272.1.62.1.1.7.1.10 | ColumnrcIpv6NetToPhysicalBMac | read-only | current | If the rcIpv6NetToPhysicalEntry is learned from a SPBM network, instead of using port to track where the rcIpv6NetToPhysicalNetAddress come from, the backbone … |
| 1.3.6.1.4.1.2272.1.62.1.1.7.1.11 | ColumnrcIpv6NetToPhysicalCvid | read-only | current | Used to identify customer vid of the switched uni port of this entry is associated with. 4095 is not used. 4096 is reserved for untagged case. |
| 1.3.6.1.4.1.2272.1.62.1.1.8 | TablercIpv6PrefixListTable | not-accessible | current | IPv6 Prefix List table |
| 1.3.6.1.4.1.2272.1.62.1.1.8.1 | RowrcIpv6PrefixListEntry | not-accessible | current | An entry of Ipv6 Prefix List Table. |
| 1.3.6.1.4.1.2272.1.62.1.1.8.1.1 | ColumnrcIpv6PrefixListId | not-accessible | current | Id of an IPv6 Prefix List |
| 1.3.6.1.4.1.2272.1.62.1.1.8.1.2 | ColumnrcIpv6PrefixListPrefix | not-accessible | current | Is a member of a specific ipv6 prefix list. Adding the prefix to the given ipv6 prefix list |
| 1.3.6.1.4.1.2272.1.62.1.1.8.1.3 | ColumnrcIpv6PrefixListPrefixMaskLen | not-accessible | current | Mask length of the ipv6 prefix added to the prefix list |
| 1.3.6.1.4.1.2272.1.62.1.1.8.1.4 | ColumnrcIpv6PrefixListMaskLenFrom | read-create | current | Lower bound of mask length of the ipv6 prefix added to the prefix list |
| 1.3.6.1.4.1.2272.1.62.1.1.8.1.5 | ColumnrcIpv6PrefixListMaskLenUpto | read-create | current | Higher bound of mask length of the ipv6 prefix added to the prefix list |
| 1.3.6.1.4.1.2272.1.62.1.1.8.1.6 | ColumnrcIpv6PrefixListName | read-create | current | Name of the Ipv6 prefix list |
| 1.3.6.1.4.1.2272.1.62.1.1.8.1.7 | ColumnrcIpv6PrefixListRowStatus | read-create | current | Used to create/delete entries in the ipv6 prefix list table |
| 1.3.6.1.4.1.2272.1.62.1.1.9 | TablercIpv6ConfDhcpRelayTable | not-accessible | current | DHCP Relay for Ipv6 configuration table |
| 1.3.6.1.4.1.2272.1.62.1.1.9.1 | RowrcIpv6ConfDhcpRelayEntry | not-accessible | current | Used to configure DHCP on a particular L3 interface. An entry is created automatically when the variable rcIpv6InterfaceDhcpEnabled is set to TRUE. Once create… |
| 1.3.6.1.4.1.2272.1.62.1.1.9.1.1 | ColumnrcIpv6ConfDhcpIfIndex | not-accessible | current | Interface number. The number can represent either a physical or logical(VLAN) interface. |
| 1.3.6.1.4.1.2272.1.62.1.1.9.1.2 | ColumnrcIpv6ConfDhcpMaxHop | read-create | current | Used to indicate the maximum number of hops a DHCP packet can take from the source device to the destination device (i.e., DHCP client to DHCP server). |
| 1.3.6.1.4.1.2272.1.62.1.1.9.1.3 | ColumnrcIpv6ConfDhcpRemoteIdEnabled | read-create | current | Used to indicate if remote-id option is enabled. |
| 1.3.6.1.4.1.2272.1.62.1.1.9.1.4 | ColumnrcIpv6ConfDhcpNumRequests | read-only | current | The total number of DHCP requests seen on this interface. |
| 1.3.6.1.4.1.2272.1.62.1.1.9.1.5 | ColumnrcIpv6ConfDhcpNumReplies | read-only | current | The total number of DHCP replies seen on this interface. |
| 1.3.6.1.4.1.2272.1.62.1.1.9.1.6 | ColumnrcIpv6ConfDhcpRowStatus | read-create | current | An entry is created automatically when the variable rcIpv6InterfaceDhcpEnabled is set to TRUE. Once created this entry will only be deleted if the rcIpv6ConfDh… |
| 1.3.6.1.4.1.2272.1.62.1.1.10 | TablercIpv6DhcpForwardTable | not-accessible | current | DHCP Relay forwarding table. |
| 1.3.6.1.4.1.2272.1.62.1.1.10.1 | RowrcIpv6DhcpForwardEntry | not-accessible | current | An entry used represents a DHCP Relayed message forwarding directive. |
| 1.3.6.1.4.1.2272.1.62.1.1.10.1.1 | ColumnrcIpv6DhcpForwardAgentAddr | not-accessible | current | The IP address configured on an interface (i.e., a locally configured IP address). |
| 1.3.6.1.4.1.2272.1.62.1.1.10.1.2 | ColumnrcIpv6DhcpForwardServerAddr | not-accessible | current | The IP address of the DHCP server. If this IP address corresponds to a local interface address, the DHCP packet is multicast out the interface the IP address i… |
| 1.3.6.1.4.1.2272.1.62.1.1.10.1.3 | ColumnrcIpv6DhcpForwardEnabled | read-create | current | Used to indicate whether the entry should be used. |
| 1.3.6.1.4.1.2272.1.62.1.1.10.1.4 | ColumnrcIpv6DhcpForwardRowStatus | read-create | current | Row status of this entry. |
| 1.3.6.1.4.1.2272.1.62.1.1.11 | TablercIpv6RadiusServTable | not-accessible | current | The RADIUS table (0 to 10 entries). This table lists the information of the RADIUS server. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1 | RowrcIpv6RadiusServEntry | not-accessible | current | A RADIUS server table entry. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.1 | ColumnrcIpv6RadiusServAddress | not-accessible | current | Server IP address of the RADIUS authentication server referred to in this table entry. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.2 | ColumnrcIpv6RadiusServUsedBy | not-accessible | current | cli(1): for cli login, igap(2): for igap,snmp(3): for snmp login, eap(4) for EAP PAE Authenticator, web(5) for EDM. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.3 | ColumnrcIpv6RadiusServPriority | read-create | current | Server priority, used to control which server to choose first to send authentication. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.4 | ColumnrcIpv6RadiusServTimeOut | read-create | current | The time interval in seconds before the client retransmit the packet. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.5 | ColumnrcIpv6RadiusServEnable | read-create | current | Enable or disable this server. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.6 | ColumnrcIpv6RadiusServMaxRetries | read-create | current | Maximum number of retransmissions. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.7 | ColumnrcIpv6RadiusServUdpPort | read-create | current | The UDP port the client is using to send requests to this server. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.8 | ColumnrcIpv6RadiusServSecretKey | read-create | current | The identifier of the RADIUS authentication client. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.9 | ColumnrcIpv6RadiusServAccessRequests | read-only | current | The number of RADIUS access-response packets sent to this server. This does not include retransmissions. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.10 | ColumnrcIpv6RadiusServAccessAccepts | read-only | current | The number of RADIUS access-accept packets (valid or invalid) received from this server. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.11 | ColumnrcIpv6RadiusServAccessRejects | read-only | current | The number of RADIUS access-reject packets (valid or invalid) received from this server. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.12 | ColumnrcIpv6RadiusServBadResponses | read-only | current | The number of RADIUS invalid access-response packets received from this server. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.13 | ColumnrcIpv6RadiusServPendingRequests | read-only | current | The number of RADIUS access-request packets destined for this server that have not yet timed out or received a response. This variable is incremented when an a… |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.14 | ColumnrcIpv6RadiusServClientRetries | read-only | current | The number of authentication retransmission to this server. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.15 | ColumnrcIpv6RadiusServAcctEnable | read-create | current | Enable or disable Radius Accounting on this server. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.16 | ColumnrcIpv6RadiusServAcctUdpPort | read-create | current | The UDP port the client used to send accounting requests to this server. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.17 | ColumnrcIpv6RadiusServAcctOnRequests | read-only | current | The number of RADIUS accounting-on packets sent to this server. This does not include retransmissions. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.18 | ColumnrcIpv6RadiusServAcctOffRequests | read-only | current | The number of RADIUS accounting-off packets sent to this server. This does not include retransmissions. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.19 | ColumnrcIpv6RadiusServAcctStartRequests | read-only | current | The number of RADIUS accounting-start packets sent to this server. This does not include retransmissions. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.20 | ColumnrcIpv6RadiusServAcctStopRequests | read-only | current | The number of RADIUS accounting-stop packets sent to this server. This does not include retransmissions. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.21 | ColumnrcIpv6RadiusServAcctInterimRequests | read-only | current | The number of RADIUS accounting-interim packets sent to this server. This does not include retransmissions. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.22 | ColumnrcIpv6RadiusServAcctBadResponses | read-only | current | The number of Invalid responses received from this server. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.23 | ColumnrcIpv6RadiusServAcctPendingRequests | read-only | current | The number of RADIUS accounting packets that are waiting be sent to this server. This variable is incremented whenever any accounting-request is sent to this s… |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.24 | ColumnrcIpv6RadiusServAcctClientRetries | read-only | current | The number of RADIUS accounting packets retransmitted to this server. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.25 | ColumnrcIpv6RadiusServNasIpAddress | read-only | current | RADIUS Client NAS Identifier for this server. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.26 | ColumnrcIpv6RadiusServRoundTripTime | read-only | current | Time different between the instance when a RADIUS request is sent and the corresponding response is received. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.27 | ColumnrcIpv6RadiusServAccessChallanges | read-only | current | The number of RADIUS access-challanges packets sent to this server. This does not include retransmission. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.28 | ColumnrcIpv6RadiusServSourceIpAddr | read-create | current | source IP address RADIUS packets. |
| 1.3.6.1.4.1.2272.1.62.1.1.11.1.29 | ColumnrcIpv6RadiusServRowStatus | read-create | current | Used to create/delete entries. |
| 1.3.6.1.4.1.2272.1.62.1.1.12 | TablercIpv6MgmtPortStaticRouteTable | not-accessible | current | This table contains list of routes that are created by the user to destination networks on the management port. |
| 1.3.6.1.4.1.2272.1.62.1.1.12.1 | RowrcIpv6MgmtPortStaticRouteEntry | not-accessible | current | An entry in the static route table for IPv6 can be created for a destination with a specific prefix length; multiple entries to the same destination are create… |
| 1.3.6.1.4.1.2272.1.62.1.1.12.1.1 | ColumnrcIpv6MgmtPortStaticRouteIfIndex | not-accessible | current | The ifIndex value which identifies the local interface through which the next hop of this route should be reached. A value of 0 is valid and represents the sce… |
| 1.3.6.1.4.1.2272.1.62.1.1.12.1.2 | ColumnrcIpv6MgmtPortStaticRouteDest | not-accessible | current | The destination IPv6 address of this route. The values for the index objects rcIpv6StaticRouteDest and rcIpv6StaticRoutePrefixLength must be consistent. When t… |
| 1.3.6.1.4.1.2272.1.62.1.1.12.1.3 | ColumnrcIpv6MgmtPortStaticRoutePrefixLength | not-accessible | current | Indicates the number of leading one bits which form the mask to be logical-ANDed with the destination address before being compared to the value in the rcIpv6M… |
| 1.3.6.1.4.1.2272.1.62.1.1.12.1.4 | ColumnrcIpv6MgmtPortStaticRouteNextHop | not-accessible | current | Next hop IPv6 address for this destination. On remote routes, the address of the next system en route. For non-remote routes, a zero length string. |
| 1.3.6.1.4.1.2272.1.62.1.1.12.1.5 | ColumnrcIpv6MgmtPortStaticRouteDistance | read-create | current | cost/distance to reach the destination for this node. |
| 1.3.6.1.4.1.2272.1.62.1.1.12.1.6 | ColumnrcIpv6MgmtPortStaticRouteStatus | read-only | current | (1)notReachable means the route is not reachable and no neighbor request entry is built to resolved the next-hop. It happens when there is no route or neighbor… |
| 1.3.6.1.4.1.2272.1.62.1.1.12.1.7 | ColumnrcIpv6MgmtPortStaticRoutePreference | read-create | current | Used to indicate the route preference of this entry. If there are more than one route that can be used to forward IP traffic, the route that has a highest pref… |
| 1.3.6.1.4.1.2272.1.62.1.1.12.1.8 | ColumnrcIpv6MgmtPortStaticRouteEnable | read-create | current | Used to enable/disable this entry. |
| 1.3.6.1.4.1.2272.1.62.1.1.12.1.9 | ColumnrcIpv6MgmtPortStaticRouteRowStatus | read-create | current | Row status for create/delete. |
| 1.3.6.1.4.1.2272.1.62.1.1.13 | TablercIpv6DestinationCacheTable | not-accessible | current | Ipv6 Destination Cache table |
| 1.3.6.1.4.1.2272.1.62.1.1.13.1 | RowrcIpv6DestinationCacheEntry | not-accessible | current | Used to display Destination Cache |
| 1.3.6.1.4.1.2272.1.62.1.1.13.1.1 | ColumnrcIpv6DCacheDestAddr | not-accessible | current | IPv6 Destination Address from the Destination Cache. |
| 1.3.6.1.4.1.2272.1.62.1.1.13.1.2 | ColumnrcIpv6DCacheIfIndex | not-accessible | current | The last 16 bits of this object's value are interpreted as InterfaceIndex (it can represent either a physical, or a VLAN, or a tunnel interface); the first 16 … |
| 1.3.6.1.4.1.2272.1.62.1.1.13.1.3 | ColumnrcIpv6DCacheNextHop | read-only | current | Ipv6 Next Hop for a Destination Cache entry. |
| 1.3.6.1.4.1.2272.1.62.1.1.13.1.4 | ColumnrcIpv6DCacheIfType | read-only | current | Interface type; it can be a real (i.e. VLAN, brouter, tunnel) or a virtual circuit (i.e. VRRP, RSMLT). |
| 1.3.6.1.4.1.2272.1.62.1.1.13.1.5 | ColumnrcIpv6DCacheIfData | read-only | current | Used to display additional information about virtual circuits (i.e. if it is a VRRP or RSMLT circuit, the vrId if it is a VRRP circuit); no information is disp… |
| 1.3.6.1.4.1.2272.1.62.1.1.13.1.6 | ColumnrcIpv6DCachePmtu | read-only | current | Path MTU for the entry. |
| 1.3.6.1.4.1.2272.1.62.1.1.13.1.7 | ColumnrcIpv6DCachePmtuAge | read-only | current | Indicates how much time (in seconds) has passed since the PMTU was updated the last time. |
| 1.3.6.1.4.1.2272.1.62.1.1.14 | TablercIpv6InterfaceBfdTable | not-accessible | current | BFD configuration table |
| 1.3.6.1.4.1.2272.1.62.1.1.14.1 | RowrcIpv6InterfaceBfdEntry | not-accessible | current | Used to configure BFD on a particular interface. An entry is created automatically when the variable rcIpv6InterfaceBfdEnable is set to TRUE and deleted when r… |
| 1.3.6.1.4.1.2272.1.62.1.1.14.1.1 | ColumnrcIpv6InterfaceBfdIfIndex | not-accessible | current | Interface number. The number can represent either a physical or logical(VLAN) interface. |
| 1.3.6.1.4.1.2272.1.62.1.1.14.1.2 | ColumnrcIpv6InterfaceBfdMinRxInterval | read-write | current | the min rx interval in milliseconds |
| 1.3.6.1.4.1.2272.1.62.1.1.14.1.3 | ColumnrcIpv6InterfaceBfdTxInterval | read-write | current | the desired tx interval in milliseconds |
| 1.3.6.1.4.1.2272.1.62.1.1.14.1.4 | ColumnrcIpv6InterfaceBfdMultiplier | read-write | current | the multiplier BFD wait before rx timeout |
| 1.3.6.1.4.1.2272.1.62.1.1.14.1.6 | ColumnrcIpv6InterfaceBfdHoldOffInterval | read-write | current | This object specifies the hold off timer interval, in seconds. 0 means that hold off timer is disabled. |
| 1.3.6.1.4.1.2272.1.62.1.1.14.1.7 | ColumnrcIpv6InterfaceBfdStaticFlag | read-write | current | This object specifies the static-flag for bfd. When disabled, the static route will go down, when bfd is disabled. |
| 1.3.6.1.4.1.2272.1.62.1.1.14.1.8 | ColumnrcIpv6InterfaceBfdVrfId | read-write | current | Indicates the Virtual Router to which the IPv6 BFD instance belongs. |
| 1.3.6.1.4.1.2272.1.62.1.1.14.1.9 | ColumnrcIpv6InterfaceBfdVrfName | read-only | current | The Name of the Virtual Router to which the IPv6 BFD instance belongs. |
| 1.3.6.1.4.1.2272.1.62.1.1.15 | TablercIpv6RouteTable | not-accessible | current | This entity's IPV6 Routing table. |
| 1.3.6.1.4.1.2272.1.62.1.1.15.1 | RowrcIpv6RouteEntry | not-accessible | current | A route to a particular destination. |
| 1.3.6.1.4.1.2272.1.62.1.1.15.1.1 | ColumnrcIpv6RouteDest | not-accessible | current | The destination IPv6 address of this route. This object may not take a Multicast address value. |
| 1.3.6.1.4.1.2272.1.62.1.1.15.1.2 | ColumnrcIpv6RoutePfxLength | not-accessible | current | Indicates the prefix length of the destination address. |
| 1.3.6.1.4.1.2272.1.62.1.1.15.1.3 | ColumnrcIpv6RouteIndex | not-accessible | current | The value which uniquely identifies the route among the routes to the same network layer destination. The way this value is chosen is implementation specific b… |
| 1.3.6.1.4.1.2272.1.62.1.1.15.1.4 | ColumnrcIpv6RouteNextHopId | read-only | current | Identifier of the next-hop, hostname or mac adress. |
| 1.3.6.1.4.1.2272.1.62.1.1.16 | TablercIpv6DefaultRoutersTable | not-accessible | current | IPv6 Default Routers Table. |
| 1.3.6.1.4.1.2272.1.62.1.1.16.1 | RowrcIpv6DefaultRoutersEntry | not-accessible | current | The entry for the IPv6 Default Routers Table. |
| 1.3.6.1.4.1.2272.1.62.1.1.16.1.1 | ColumnrcIpv6DefaultRoutersAddress | not-accessible | current | Learned Router Address for an IPv6 Default Routers Entry. |
| 1.3.6.1.4.1.2272.1.62.1.1.16.1.2 | ColumnrcIpv6DefaultRoutersIfIndex | not-accessible | current | Interface number for an IPv6 Default Routers Entry. |
| 1.3.6.1.4.1.2272.1.62.1.1.16.1.3 | ColumnrcIpv6DefaultRoutersLifetime | read-only | current | Remaining Router Lifetime for an IPv6 Default Routers Entry. |
| 1.3.6.1.4.1.2272.1.62.1.1.16.1.4 | ColumnrcIpv6DefaultRoutersActive | read-only | current | See if a default router is active for an IPv6 Default Routers Entry. |
| 1.3.6.1.4.1.2272.1.62.1.1.17 | TablercIpv6MLDHostCacheTable | not-accessible | current | IPv6 MLD Host Cache Table. |
| 1.3.6.1.4.1.2272.1.62.1.1.17.1 | RowrcIpv6MLDHostCacheEntry | not-accessible | current | The entry for the IPv6 MLD Host Cache Table. |
| 1.3.6.1.4.1.2272.1.62.1.1.17.1.1 | ColumnrcIpv6MLDHostCacheIfIndex | not-accessible | current | Interface number for an IPv6 MLD Host Cache Entry. |
| 1.3.6.1.4.1.2272.1.62.1.1.17.1.2 | ColumnrcIpv6MLDHostCacheGrpAddress | not-accessible | current | Group Address for an IPv6 MLD Host Cache Entry. |
| 1.3.6.1.4.1.2272.1.62.1.1.17.1.3 | ColumnrcIpv6MLDHostCacheGrpLocallyRegistered | read-only | current | Group Locally Registered for an IPv6 MLD Host Cache Entry. |
| 1.3.6.1.4.1.2272.1.62.1.1.17.1.4 | ColumnrcIpv6MLDHostCacheGrpLastReporter | read-only | current | Group Last Reporter Address for an IPv6 MLD Host Cache Entry. |
| 1.3.6.1.4.1.2272.1.62.1.1.17.1.5 | ColumnrcIpv6MLDHostCacheGrpUpTime | read-only | current | Group Uptime for an IPv6 MLD Host Cache Entry. |
| 1.3.6.1.4.1.2272.1.62.1.1.17.1.6 | ColumnrcIpv6MLDHostCacheGrpExpiryTime | read-only | current | Group Expiry Time for an IPv6 MLD Host Cache Entry. |
| 1.3.6.1.4.1.2272.1.62.1.1.17.1.7 | ColumnrcIpv6MLDHostCacheGrpFilterMode | read-only | current | Group Filter Mode for an IPv6 MLD Host Cache Entry. |
| 1.3.6.1.4.1.2272.1.62.1.1.18 | TablercTunnelXInetConfigTable | not-accessible | current | A table that containing information on configured tunnels. |
| 1.3.6.1.4.1.2272.1.62.1.1.18.1 | RowrcTunnelXInetConfigEntry | not-accessible | current | An entry containing additional tunnel information. This object augments tunnelInetConfigEntry. |
| 1.3.6.1.4.1.2272.1.62.1.1.18.1.1 | ColumnrcTunnelXInetConfigStatus | read-create | current | Indicates the tunnel status |
| 1.3.6.1.4.1.2272.1.62.1.1.18.1.2 | ColumnrcTunnelXInetConfigMode | read-create | current | Indicates the tunnel mode |
| 1.3.6.1.4.1.2272.1.62.1.1.19 | TablercIpv6RouteExtensionTable | not-accessible | current | This entity's IPV6 Routing table. |
| 1.3.6.1.4.1.2272.1.62.1.1.19.1 | RowrcIpv6RouteExtensionEntry | not-accessible | current | A route to a particular destination. |
| 1.3.6.1.4.1.2272.1.62.1.1.19.1.1 | ColumnrcIpv6RouteExtensionNextHopId | read-only | current | Identifier of the next-hop, hostname or mac adress. |
| 1.3.6.1.4.1.2272.1.62.1.1.19.1.2 | ColumnrcIpv6RouteExtensionProtocol | read-only | current | The routing mechanism via which this route was learned. |
| 1.3.6.1.4.1.2272.1.62.1.1.19.1.3 | ColumnrcIpv6RouteExtensionPathType | read-only | current | Indicates IPv6 route path type: best, alternative, ECMP. |
| 1.3.6.1.4.1.2272.1.62.1.1.19.1.4 | ColumnrcIpv6RouteExtensionSrcVrfId | read-only | current | srcVrfId of the next-hop address. If the route is an ISIS route, advertised under an ISID that i snot locally configured, on any VRF, srcVrfId will be 1023 |
| 1.3.6.1.4.1.2272.1.62.1.1.19.1.5 | ColumnrcIpv6RouteExtensionLayer3VirtualInterface | read-only | current | Identifier of the Layer 3 Virtual Interface - SPB I-SID. 0 denotes GlobalRouter and 1 denotes not applicable to route |
| 1.3.6.1.4.1.2272.1.62.1.1.20 | TablercIpv6RoutePrefTable | not-accessible | current | IPv6 Route Pref table. This table and rcIpNewRoutePrefTable is designed to obsolete the rcIpRoutePrefTable |
| 1.3.6.1.4.1.2272.1.62.1.1.20.1 | RowrcIpv6RoutePrefEntry | not-accessible | current | An entry of Ipv6 Route Pref Table. |
| 1.3.6.1.4.1.2272.1.62.1.1.20.1.1 | ColumnrcIpv6RoutePrefDefaultValue | not-accessible | current | Shows the default preference value for the given protocol. |
| 1.3.6.1.4.1.2272.1.62.1.1.20.1.2 | ColumnrcIpv6RoutePrefProtocol | read-only | current | Protocol name |
| 1.3.6.1.4.1.2272.1.62.1.1.20.1.3 | ColumnrcIpv6RoutePrefConfiguredValue | read-write | current | This value is configurable by the user |
| 1.3.6.1.4.1.2272.1.62.1.1.21 | TablercIpv6FhsSnoopTable | not-accessible | current | This table contains the entries which are snooped by different methods. |
| 1.3.6.1.4.1.2272.1.62.1.1.21.1 | RowrcIpv6FhsSnoopEntry | not-accessible | current | An entry containing a learned DHCPv6 binding. |
| 1.3.6.1.4.1.2272.1.62.1.1.21.1.1 | ColumnrcIpv6FhsSnoopVlanId | not-accessible | current | The VLAN to which the snooped entry belongs. |
| 1.3.6.1.4.1.2272.1.62.1.1.21.1.2 | ColumnrcIpv6FhsSnoopIpv6Address | not-accessible | current | The IPv6 address assigned to this IPv6 host. |
| 1.3.6.1.4.1.2272.1.62.1.1.21.1.3 | ColumnrcIpv6FhsSnoopMacAddress | read-create | current | The MAC address of the snooped entry. |
| 1.3.6.1.4.1.2272.1.62.1.1.21.1.4 | ColumnrcIpv6FhsSnoopInterfaceIndex | read-create | current | The interface on which the entry is learnt. |
| 1.3.6.1.4.1.2272.1.62.1.1.21.1.5 | ColumnrcIpv6FhsSnoopEntryType | read-only | current | Indicates the type of entry - static (1) or dynamic (2). |
| 1.3.6.1.4.1.2272.1.62.1.1.21.1.6 | ColumnrcIpv6FhsSnoopEntrySource | read-only | current | Indicates the method entry was learnt from - static (1) or dhcp (2). |
| 1.3.6.1.4.1.2272.1.62.1.1.21.1.7 | ColumnrcIpv6FhsSnoopValidTime | read-create | current | The valid time for the snooped entry. |
| 1.3.6.1.4.1.2272.1.62.1.1.21.1.8 | ColumnrcIpv6FhsSnoopTimeToExpiry | read-only | current | The time to expiry of the snooped entry. |
| 1.3.6.1.4.1.2272.1.62.1.1.21.1.9 | ColumnrcIpv6FhsSnoopRowStatus | read-create | current | Row status to create/delete snooped entries. |
| 1.3.6.1.4.1.2272.1.62.1.1.22 | NodercIpv6FhsSnoopNotificationObjects | |||
| 1.3.6.1.4.1.2272.1.62.1.1.22.1 | ScalarrcIpv6FhsSnoopNotificationEntryType | accessible-for-notify | current | This value indicates type of binding entry. static (1) entries are created by administrator manually whereas dynamic (2) entries are learnt through snooping. |
| 1.3.6.1.4.1.2272.1.62.1.1.22.2 | ScalarrcIpv6FhsSnoopNotificationEntryCount | accessible-for-notify | current | This value indicates current number of binding entries of type rcIpv6FhsSnoopingNotificationEntryType |
| 1.3.6.1.4.1.2272.1.62.1.1.23 | NodercIpv6IsisInFilterObjects | |||
| 1.3.6.1.4.1.2272.1.62.1.1.23.1 | TablercIpv6IsisInFilterNickNameTable | not-accessible | current | IPv6 Isis In Filter Nick Name table |
| 1.3.6.1.4.1.2272.1.62.1.1.23.1.1 | RowrcIpv6IsisInFilterNickNameEntry | not-accessible | current | An entry of Ipv6 Isis In Filter Nick Name Table. |
| 1.3.6.1.4.1.2272.1.62.1.1.23.1.1.1 | ColumnrcIpv6IsisInFilterNickNameAdvertisingRtr | not-accessible | current | NickName used to filter by |
| 1.3.6.1.4.1.2272.1.62.1.1.23.1.1.2 | ColumnrcIpv6IsisInFilterNickNameEnable | read-create | current | Enables or disables the Nick Name entry. The value must be enabled to filter. |
| 1.3.6.1.4.1.2272.1.62.1.1.23.1.1.3 | ColumnrcIpv6IsisInFilterNickNamePolicyName | read-create | current | Route Map name used |
| 1.3.6.1.4.1.2272.1.62.1.1.23.1.1.4 | ColumnrcIpv6IsisInFilterNickNameRowStatus | read-create | current | Ipv6 Isis In Filter Nick Name Table Row Status |
| 1.3.6.1.4.1.2272.1.62.1.1.23.2 | TablercIpv6IsisInFilterIsidTable | not-accessible | current | IPv6 Isis In Filter Isid Isid table |
| 1.3.6.1.4.1.2272.1.62.1.1.23.2.1 | RowrcIpv6IsisInFilterIsidEntry | not-accessible | current | An entry of Ipv6 Isis In Filter Table. |
| 1.3.6.1.4.1.2272.1.62.1.1.23.2.1.1 | ColumnrcIpv6IsisInFilterIsid | not-accessible | current | Isid value used to filter by |
| 1.3.6.1.4.1.2272.1.62.1.1.23.2.1.2 | ColumnrcIpv6IsisInFilterIsidEnable | read-create | current | Enables or disables the Isid entry. The value must be enabled to filter. |
| 1.3.6.1.4.1.2272.1.62.1.1.23.2.1.3 | ColumnrcIpv6IsisInFilterIsidPolicyName | read-create | current | Route Map name used |
| 1.3.6.1.4.1.2272.1.62.1.1.23.2.1.4 | ColumnrcIpv6IsisInFilterIsidRowStatus | read-create | current | IPv6 Isis In Filter Isid Table Row Status |
| 1.3.6.1.4.1.2272.1.62.1.1.23.3 | TablercIpv6IsisInFilterNickNameIsidTable | not-accessible | current | IPv6 Isis In Filter Nick Name Isid table |
| 1.3.6.1.4.1.2272.1.62.1.1.23.3.1 | RowrcIpv6IsisInFilterNickNameIsidEntry | not-accessible | current | An entry of IPv6 Isis In Filter Nick Name Isid Table. |
| 1.3.6.1.4.1.2272.1.62.1.1.23.3.1.1 | ColumnrcIpv6IsisInFilterNickNameIsidAdvertisingRtr | not-accessible | current | Nick Name used to filter by |
| 1.3.6.1.4.1.2272.1.62.1.1.23.3.1.2 | ColumnrcIpv6IsisInFilterNickNameIsid | not-accessible | current | Isid used to filter by |
| 1.3.6.1.4.1.2272.1.62.1.1.23.3.1.3 | ColumnrcIpv6IsisInFilterNickNameIsidEnable | read-create | current | |
| 1.3.6.1.4.1.2272.1.62.1.1.23.3.1.4 | ColumnrcIpv6IsisInFilterNickNameIsidPolicyName | read-create | current | Route Map name used |
| 1.3.6.1.4.1.2272.1.62.1.1.23.3.1.5 | ColumnrcIpv6IsisInFilterNickNameIsidRowStatus | read-create | current | IPv6 Isis In Filter Nick Name Isid Table Row Status |
| 1.3.6.1.4.1.2272.1.62.1.1.23.4 | TablercIpv6IsisInFilterIsidListTable | not-accessible | current | IPv6 Isis In Filter Isid List table |
| 1.3.6.1.4.1.2272.1.62.1.1.23.4.1 | RowrcIpv6IsisInFilterIsidListEntry | not-accessible | current | An entry of IPv6 Isis In Filter Table. |
| 1.3.6.1.4.1.2272.1.62.1.1.23.4.1.1 | ColumnrcIpv6IsisInFilterIsidListName | not-accessible | current | Name of Isid List |
| 1.3.6.1.4.1.2272.1.62.1.1.23.4.1.2 | ColumnrcIpv6IsisInFilterIsidListEnable | read-create | current | Enables or disables the Isid List entry. The value must be enabled to filter. |
| 1.3.6.1.4.1.2272.1.62.1.1.23.4.1.3 | ColumnrcIpv6IsisInFilterIsidListPolicyName | read-create | current | Route Map name |
| 1.3.6.1.4.1.2272.1.62.1.1.23.4.1.4 | ColumnrcIpv6IsisInFilterIsidListRowStatus | read-create | current | IPv6 Isis In Filter Isid List Table Row Status |
| 1.3.6.1.4.1.2272.1.62.1.1.23.5 | TablercIpv6IsisInFilterNickNameIsidListTable | not-accessible | current | IPv6 Isis In Filter Nick Name Isid List table |
| 1.3.6.1.4.1.2272.1.62.1.1.23.5.1 | RowrcIpv6IsisInFilterNickNameIsidListEntry | not-accessible | current | An entry of IPv6 Isis In Filter Nick Name Isid ListTable |
| 1.3.6.1.4.1.2272.1.62.1.1.23.5.1.1 | ColumnrcIpv6IsisInFilterNickNameIsidListAdvertisingRtr | not-accessible | current | Nick Name used to filter by |
| 1.3.6.1.4.1.2272.1.62.1.1.23.5.1.2 | ColumnrcIpv6IsisInFilterNickNameIsidListName | not-accessible | current | Name of Isid List used to filter |
| 1.3.6.1.4.1.2272.1.62.1.1.23.5.1.3 | ColumnrcIpv6IsisInFilterNickNameIsidListEnable | read-create | current | Enables or disables the Nick Name Isid List entry. The value must be enabled to filter. |
| 1.3.6.1.4.1.2272.1.62.1.1.23.5.1.4 | ColumnrcIpv6IsisInFilterNickNameIsidListPolicyName | read-create | current | Route Map name |
| 1.3.6.1.4.1.2272.1.62.1.1.23.5.1.5 | ColumnrcIpv6IsisInFilterNickNameIsidListRowStatus | read-create | current | IPv6 Isis In Filter Nick Name Isid List Table Row Status |
| 1.3.6.1.4.1.2272.1.62.1.1.24 | TablercIpv6StaticRouteBfdTable | not-accessible | current | This table is used to hold next hop addresses on which BFD is enabled. |
| 1.3.6.1.4.1.2272.1.62.1.1.24.1 | RowrcIpv6StaticRouteBfdEntry | not-accessible | current | An IPv6 address of the next hop of the BFD session. |
| 1.3.6.1.4.1.2272.1.62.1.1.24.1.1 | ColumnrcIpv6StaticRouteBfdIfIndex | not-accessible | current | The IfIndex value which identifies the local interface through which the next hop of this route should be reached. |
| 1.3.6.1.4.1.2272.1.62.1.1.24.1.2 | ColumnrcIpv6StaticRouteBfdNextHop | not-accessible | current | The IPv6 address of the next hop of the BFD session. |
| 1.3.6.1.4.1.2272.1.62.1.1.24.1.3 | ColumnrcIpv6StaticRouteBfdRowStatus | read-create | current | Used to create/delete entries |
| 1.3.6.1.4.1.2272.1.62.1.1.24.1.4 | ColumnrcIpv6StaticRouteBfdVrfId | read-create | current | Indicates the Virtual Router to which the IPv6 static route BFD instance belongs. |
| 1.3.6.1.4.1.2272.1.62.1.1.24.1.5 | ColumnrcIpv6StaticRouteBfdVrfName | read-only | current | The Name of the Virtual Router to which the IPv6 static route BFD instance belongs. |
Type Definitions
| Name | Syntax | Status | Description |
|---|---|---|---|
| IpAddressOriginTC | INTEGER { other(1), manual(2), dhcp(4), linklayer(5), random(6) } | current | The origin of the address. manual(2) indicates that the address was manually configured to a specified address, e.g. by user configuration. dhcp(4) indicates an address that was assigned to this system by a DHCP server.… |
| IpAddressStatusTC | INTEGER { preferred(1), deprecated(2), invalid(3), inaccessible(4), unknown(5), tentative(6), duplicate(7) } | current | The status of an address. Most of the states correspond to states from the IPv6 Stateless Address Autoconfiguration protocol [5]. The preferred(1) state indicates that this is a valid address that can appear as the dest… |
| Ipv6NextHdr | INTEGER { hop-by-hop(0), icmpv4(1), igmpv4(2), ipInIp(4), tcp(6), egp(8), udp(17), ipv6(41), routing(43), frag(44), rsvp(46), ipsecESP(50), ipsecAh(51), icmpv6(58), noNxtHdr(59), destOptions(60), undefined(255) } | current | The ipv6 next header to look for. |